APR3021/2/3 MicroPower Microprocessor Reset Circuit Features • • • • • • • • General Description 1.2V to 5.5V Input Voltage Range The APR3021/2/3 are designed to monitor voltage Low Quiescent Current : less Than 1.5 µA supplies in µP and digital systems. The quiescent High accuracy detection threshold : ±1.5% current is extremely low, typically 1.5 µA, making it Fixed trimmed reset thresholds for 1.5V, 1.75V, ideal for portable battery operated equipment. The 2.32V, 2.63V, 2.93V, 3.08V, 3.9V, 4.38V. APR3021/2/3 operate by monitoring the system Reset Timeout Period 250ms power supply voltage. When the input voltage drops Available output configurations below a fixed threshold, the device asserts a reset - Open-drain output - CMOS active high output - CMOS active low output signal for a fixed time period after Vcc rises above the fixed threshold. The APR3021/2/3 series is available with three output stage versions : APR3021 SOT-23 , SOT-23-5 and SOT-89 packages push-pull active low output, APR3022 push-pull ac- No external components tive high output and APR3023 open drain active low Applications output. They are also designed to reject fast line transient glitches on Vcc. The APR3021/2/3 are come in • • • • a miniature SOT-23, SOT-23-5, SOT-89 packages. Computers Cell Phones Pin Configuration Portable Electronics µP Power Supply Monitoring NC GND 3 5 1 (3 0 2 1 /3 ) R e s e t (3 0 2 2 ) R e s e t 2 1 (3021/3) Reset (3022) Reset 4 2 3 (3021/3) Reset GND V CC (3022) Reset V CC SOT-23 (Top View) 1 NC 2 3 GND V CC SOT-23-5 (Top View) SOT-89 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 1 www.anpec.com.tw APR3021/2/3 Ordering and Marking Information P a cka g e C o d e A : S O T -23 B : S O T -23-5 D : S O T -89 T e m p . R a nge I : -4 0 to 85 ° C H andling C ode T R : T ape & R eel V o ltage C o de : 15 : 1.5V ~ 43 : 4 .38 V Lea d F re e C ode L : L e a d F re e D evice B la n k : O rigin a l D e vice A P R 3 02 1/2 /3 Lea d F re e C ode H andling C ode T e m p . R a nge P a cka g e C o d e V o ltage C o de A P R 3 021/2/3 A /B : 21 /2/3 X X A P R 3 021/2/3 -15 D : D ate C ode V o ltage C o de A :1.5V B :1.75V C :2.32V D :2.63V E :2.93V F :3.0 8V G :3.9V H :4.3 8V A P R 3 021/2/3 XX XX X 15 XX XX X - D ate C ode ; 15 - 1.5V Absolute Maximum Ratings Symbol VCC Parameter VCC to GND Value Unit -0.3 to 6 V VRESET RESET to GND (Push-Pull Output) RESET to GND (Open Drain Output) -0.3 to VCC +0.3 -0.3 to 6 V IMAX Maximum Continuous Input Current 20 mA RESET/RESET Current 20 mA Rate of Rise of VCC 100 V/µs -40 to 150 °C 260 357 357 180 Internally Limited °C IRESET dVcc/dt TJ Junction Temperature Range TL Lead Temperature (Soldering, 10 second) RTH,JA Thermal Resistance – Junction to Ambient PD SOT-23 SOT-23-5 SOT-89 Power Dissipation °C/W W Pin Descrpition No. 1 2 3 PIN Name RESET (APR3021/3) RESET (APR3022) VCC GND Description RESET output remains low while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold RESET output remains high while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold. Supply Voltage (+1.2V to +6V) Ground connection Note: The pin sequence here might not be correct for all different package types, and please refer pin configuration in page1 for correct pin assignment. Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 2 www.anpec.com.tw APR3021/2/3 Block Diagram Vc c Reset Generator + Timer RESET Oscillator VREF APR3021 GND Vc c Reset Generator + Timer RESET Oscillator VREF APR3022 GND RESET Vc c Reset Generator + Timer Oscillator VREF GND Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 APR3023 3 www.anpec.com.tw APR3021/2/3 Part Number Description Part Number APR3021 APR3022 APR3023 Part Description Reset Output Push Pull Active Low with Delay Reset Output Push Pull Active High with Delay Reset Output Open Drain Active Low with Delay Electrical Characteristics VIN = 5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C, VCC = 5V for 4.38V versions, VCC = 3.3V for 3.08/2.93V versions, VCC = 3.0V for 2.63V. versions and VCC = 2.5V for 2.32V versions, VCC = 2.0V for 1.75V versions , VCC = 1.8V for 1.5V versions. Symbol Parameter VCC ICC Supply Voltage Supply Current VTH Reset Threshold VHYST TRTP VOL VOH TD ILE Test Conditions VCC=1.5V~6V T A=-40 to 85°C T A=25°C T A=-40 to 85°C Hysteresis Range Reset Timeout Period Reset Output Low Reset Output High VCC to Reset Delay Reset Output Leakage ISINK=1.2mA ISOURCE=0.6mA VCC=VTH to (VTH-100mV) APR3021/2/3 Min. Typ. Max. 1.2 6 1.5 4 3 5 ±1.5% ±2% 20 150 250 350 0.5 0.8*VCC 25 0.5 Unit V µA mV ms V µS µA Application Circuit VCC VCC VCC 100k APR3023 RESET GND Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 VCC VCC RESET µ P INPUT APR3021 RESET APR3022 (RESET) GND GND 4 VCC RESET µP INPUT GND www.anpec.com.tw APR3021/2/3 Timing Chart Reset Threshold Reset Threshold Vcc (APR3022) RESET Reset Timeout Period 250ms Vcc to Reset Delay 25us (APR3021/3) RESET Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 5 www.anpec.com.tw APR3021/2/3 Typical Characteristics Maximum Transient Duration vs. Reset Threshold Overdrive VTH - VCC Supply Current vs. Supply Voltage Maximum Transient Duration (us) 2 Supply Current (uA) 1.6 1.2 0.8 0.4 0 0 1 2 3 4 5 120 100 generate a reset signal 80 60 40 20 never generate a reset signal 0 6 10 Supply Voltage (V) 1000 Reset Threshold Overdrive VTH - VCC (mV) Output Source Current vs. Reset High Output Voltage Output Sink Current vs. Reset Low Output Voltage 70 50 Vcc=5V 50 Vcc=4V 40 30 Vcc=2.9V 45 60 Output Sink Current (mA) Output Source Current (mA) 100 Vcc=3V 20 10 0 40 35 Vcc=2.5V 30 25 Vcc=2V 20 15 Vcc=1.5 10 5 0 0 1 2 3 4 5 6 0 2 3 4 5 6 Reset Low Output Voltage (V) Reset High Output Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 1 6 www.anpec.com.tw APR3021/2/3 Typical Characteristics Reset Propagation Delay vs. Temperature 60 1.008 Reset Propagation Delay (us) Normalized Reset Threshold (%) Normalized Reset Threshold vs. Temperature 1.006 1.004 1.002 1 0.998 0.996 0.994 50 40 VOD=100mV 30 20 10 0 -40 -20 0 20 40 60 80 100 120 -40 -20 0 Temperature (°C) 40 60 80 100 120 Temperature (°C) Reset Timeout Period vs. Temperature Supply Current vs. Temperature 600 3.5 500 3 Supply Current (uA) Reset Timeout Period (ms) 20 400 300 200 100 2.5 Vcc=5V 2 1.5 Vcc=3V 1 0.5 0 0 -40 -20 0 20 40 60 80 100 120 -40 Temperature (°C) Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 -20 0 20 40 60 80 100 120 Temperature (°C) 7 www.anpec.com.tw APR3021/2/3 Typical Characteristics Power Down Power Up Vcc(2V/div) Vcc(2V/div) RESET(2V/div) RESET(2V/div) Time (50ms/div) Time (200ms/div) Vcc to RESET Delay Vcc(0.5V/div) Vcc=V TH to (VTH-100mV) RESET(2V/div) Time (10us/div) Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 8 www.anpec.com.tw APR3021/2/3 Application Information VCC Transient Rejection V CC The APR3021/2/3 have the function to reject the tranV CC sient glitches from the power line. The Maximum Transient Duration vs. Reset Threshold Overdrive shows RESET at Typical Characteristics.The transient voltage with the duration under the curve will not generate a reset signal, e.g. a transient of 100mV below the reset threshold voltage have the duration more than 35us, it will generate a reset signal. Connect a 0.1uF bypass capacitor to the VCC pin can improve the transient immunity. 100K GND Figure 1. Ensuring RESET Valid to VCC = 0 V Reset Output +3.3V The APR3021/2/3 have 3 output stage versions: APR3001 is an active low push-pull output, when the VCC drops below the reset threshold, the RESET output generates a low signal. APR3022 is an active high push-pull output, when the VCC drops below the reset threshold, the RESET output generates a high signal (see Timing Chart). APR3023 is an active low open drain output, the RESET output must be connected a pull-up resistor to a supply voltage that is lower than 6V, it suits to use in multiple voltage systems (see Figure 2). The APR3021 RESET output is valid until the VCC=1.2V, below 1.2V the IC is shutdown, and the output becomes a floating state. If it is a trouble, a resistor should be connected from reset output to ground to keep the reset output low (see Figure 1). For The APR3022, a pull-up resistor to VCC is required to keep the valid reset output for VCC below 1.2V. Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 +5.0V V CC V CC APR3023 RESET GND 100k RESET 5V INPUT System GND Figure 2. APR3023 Open Drain Output with Multiple Supplies 9 www.anpec.com.tw APR3021/2/3 Packaging Information SOT-23 D B 3 E H 2 1 e A L A1 D im A A1 B C D E e H L C M illim e t e rs M in . 1 .0 0 0 .0 0 0 .3 5 0 .1 0 2 .7 0 1 .4 0 In c h e s M ax. 1 .3 0 0 .1 0 0 .5 1 0 .2 5 3 .1 0 1 .8 0 M in . 0 .0 3 9 0 .0 0 0 0 .0 1 4 0 .0 0 4 0 .1 0 6 0 .0 5 5 3 .0 0 0 .0 9 4 0 .0 1 5 1 .9 0 /2 .1 B S C 2 .4 0 0 .3 7 Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 M ax. 0 .0 5 1 0 .0 0 4 0 .0 2 0 0 .0 1 0 0 .1 2 2 0 .0 7 1 0 .0 7 5 /0 .0 8 3 B S C 10 0 .11 8 www.anpec.com.tw APR3021/2/3 Packaging Information SOT-23-5 e1 5 4 E1 1 E 3 2 e b D A2 A a A1 Dim A A1 A2 b D E E1 e e1 L L1 L2 N α L2 L M illimeters M in . 0.95 0.05 0.90 0.30 2.8 2.6 1.5 Inches M ax. 1.45 0.15 1.30 0.50 3.00 3.00 1.70 M in. 0.037 0.002 0.035 0.011 0.110 0.102 0.059 0.55 0.014 0.7 0.020 0.20 BSC 0.5 Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 0.022 0.008 BSC 5 0° M ax. 0.057 0.006 0.051 0.019 0.118 0.118 0.067 0.037BSC 0.074BSC 0.95BSC 1.90BSC 0.35 L1 0.028 5 10° 11 0° 10° www.anpec.com.tw APR3021/2/3 Packaging Information SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62) D D1 a E H 1 2 3 L C B1 B e e1 A a D im A B B1 C D D1 e e1 E H L α M illim eters M in. 1.40 0.40 0.35 0.35 4.40 1.35 Inches M ax. 1.60 0.56 0.48 0.44 4.60 1.83 M in. 0.055 0.016 0.014 0.014 0.173 0.053 1.50 B SC 3.00 B SC 2.29 3.75 0.80 Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 M ax. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 B SC 2.60 4.25 1.20 10° 12 0.090 0.148 0.031 0.102 0.167 0.047 10° www.anpec.com.tw APR3021/2/3 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone T L to T P Temperature Ram p-up TL tL Tsm ax Tsm in Ram p-down ts Preheat 25 t 25 °C to Peak Tim e Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Average ramp-up rate 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C - Temperature Mix (Tsmax) 150°C - Time (min to max)(ts) 60-120 seconds Tsmax to TL - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C - Time (tL) 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6 minutes max. Time 25°C to Peak Temperature Pb-Free Assembly Large Body Small Body 3°C/second max. 150°C 200°C 60-180 seconds 3°C/second max 217°C 60-150 seconds 245 +0/-5°C 250 +0/-5°C 10-30 seconds 20-40 seconds 6°C/second max. 8 minutes max. Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 13 www.anpec.com.tw APR3021/2/3 Reliability test program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ao D1 Ko T2 J C A B T1 Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 14 www.anpec.com.tw APR3021/2/3 Carrier Tape & Reel Dimensions A p p lic a tio n S O T -2 3 A p p lic a tio n S O T -2 3 -5 A p p lic a tio n S O T -8 9 A B C J T1 T2 P E 1 .4 W 8 .0 + 0 .3 - 0 .3 178±1 6 0 ± 1 .0 1 2 .0 2 .5 ± 0 .1 5 9 .0 ± 0 .5 F D D1 Po P1 4 .0 1 .7 5 Ao Bo Ko t 3 .5 ± 0 .0 5 1 .5 + 0 .1 φ 0 .1 M IN 4 .0 A B C J 2 .0 ± 0 .0 5 3 .1 3 .0 1 .3 0 .2 ± 0 .0 3 T1 T2 W P 178 ±1 7 2 ± 1 .0 1 3 .0 + 0 .2 2 .5 ± 0 .1 5 E 8 .4 ± 2 1 .5 ± 0 .3 8 .0 ± 0 .3 4 ± 0 .1 1 .7 5 ± 0 .1 F D D1 Po P1 Ao Bo Ko t 3 .5 ± 0 .0 5 1 .5 ± 0 .1 1 .5 ± 0 .1 4 .0 ± 0 .1 2 .0 ± 0 .1 3 .1 5 ± 0 .1 3 .2 ± 0 .1 1 .4 ± 0 .1 0 .2 ± 0 .0 3 3 W 1 2 + 0 .3 1 2 - 0 .1 P E 8 ± 0 .1 1 .7 5 ± 0 .1 A B C J T1 T2 178 ±1 70 ± 2 1 3 .5 ± 0 .1 5 3 ± 0 .1 5 14 ± 2 1 .3 ± 0 .3 F D D1 Po P1 Ao Bo Ko t 5 .5 ± 0 .0 5 1 .5 ± 0 .1 1 .5 ± 0 .1 4 .0 ± 0 .1 2 .0 ± 0 .1 4 .8 ± 0 .1 4 .5 ± 0 .1 1 .8 0 ± 0 .1 0 .3 ± 0 .0 1 3 (mm) Cover Tape Dimensions Application SOT- 23 SOT- 23-5 SOT- 89 Carrier Width 8 8 12 Cover Tape Width 5.3 5.3 9.3 Devices Per Reel 3000 3000 1000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.2 - Oct., 2003 15 www.anpec.com.tw