AD AD9511BCPZ-REEL 1.2 ghz clock distribution ic, pll core, dividers, delay adjust, five output Datasheet

1.2 GHz Clock Distribution IC, PLL Core,
Dividers, Delay Adjust, Five Outputs
AD9511
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VS
Low jitter, low phase noise clock distribution
Clocking high speed ADCs, DACs, DDSs, DDCs, DUCs, MxFEs
High performance wireless transceivers
High performance instrumentation
Broadband infrastructure
GENERAL DESCRIPTION
The AD9511 provides a multi-output clock distribution
function along with an on-chip PLL core. The design
emphasizes low jitter and phase noise to maximize data
converter performance. Other applications with demanding
phase noise and jitter requirements also benefit from this part.
The PLL section consists of a programmable reference divider
(R); a low noise phase frequency detector (PFD); a precision
charge pump (CP); and a programmable feedback divider (N).
By connecting an external VCXO or VCO to the CLK2/CLK2B
pins, frequencies up to 1.6 GHz may be synchronized to the
input reference.
There are five independent clock outputs. Three outputs are
LVPECL (1.2 GHz), and two are selectable as either LVDS
(800 MHz) or CMOS (250 MHz) levels.
CPRSET VCP
DISTRIBUTION
REF
REFIN
R DIVIDER
REFINB
N DIVIDER
FUNCTION
AD9511
PHASE
FREQUENCY
DETECTOR
SYNCB,
RESETB
PDB
PLL
REF
CHARGE
PUMP
PLL
SETTINGS
CLK1
CP
STATUS
CLK2
CLK1B
CLK2B
PROGRAMMABLE
DIVIDERS AND
PHASE ADJUST
LVPECL
OUT0
/1, /2, /3... /31, /32
OUT0B
LVPECL
OUT1
/1, /2, /3... /31, /32
OUT1B
LVPECL
OUT2
/1, /2, /3... /31, /32
OUT2B
SCLK
SDIO
APPLICATIONS
RSET
GND
SDO
LVDS/CMOS
SERIAL
CONTROL
PORT
OUT3
/1, /2, /3... /31, /32
OUT3B
CSB
LVDS/CMOS
/1, /2, /3... /31, /32
ΔT
OUT4
OUT4B
DELAY
ADJUST
Figure 1.
Each output has a programmable divider that may be bypassed
or set to divide by any integer up to 32. The phase of one clock
output relative to another clock output may be varied by means
of a divider phase select function that serves as a coarse timing
adjustment. One of the LVDS/CMOS outputs features a
programmable delay element with full-scale ranges up to 10 ns
of delay. This fine tuning delay block has 5-bit resolution, giving
32 possible delays from which to choose for each full-scale
setting.
The AD9511 is ideally suited for data converter clocking
applications where maximum converter performance is
achieved by encode signals with subpicosecond jitter.
The AD9511 is available in a 48-lead LFCSP and can be
operated from a single 3.3 V supply. An external VCO, which
requires an extended voltage range, can be accommodated by
connecting the charge pump supply (VCP) to 5.5 V. The
temperature range is −40°C to +85°C.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
05286-001
Low phase noise phase-locked loop core
Reference input frequencies to 250 MHz
Programmable dual-modulus prescaler
Programmable charge pump (CP) current
Separate CP supply (VCPS) extends tuning range
Two 1.6 GHz, differential clock inputs
5 programmable dividers, 1 to 32, all integers
Phase select for output-to-output coarse delay adjust
3 independent 1.2 GHz LVPECL outputs
Additive output jitter 225 fs rms
2 independent 800 MHz/250 MHz LVDS/CMOS clock outputs
Additive output jitter 275 fs rms
Fine delay adjust on 1 LVDS/CMOS output
Serial control port
Space-saving 48-lead LFCSP
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2005 Analog Devices, Inc. All rights reserved.
AD9511
TABLE OF CONTENTS
Specifications..................................................................................... 4
A and B Counters................................................................... 30
PLL Characteristics ...................................................................... 4
Determining Values for P, A, B, and R ................................ 30
Clock Inputs .................................................................................. 5
Phase Frequency Detector (PFD) and Charge Pump ....... 31
Clock Outputs ............................................................................... 6
Antibacklash Pulse................................................................. 31
Timing Characteristics ................................................................ 7
STATUS Pin ............................................................................ 31
Clock Output Phase Noise .......................................................... 9
PLL Digital Lock Detect........................................................ 31
Clock Output Additive Time Jitter........................................... 12
PLL Analog Lock Detect ....................................................... 32
PLL and Distribution Phase Noise and Spurious................... 14
Loss of Reference.................................................................... 32
Serial Control Port ..................................................................... 15
FUNCTION Pin ......................................................................... 32
FUNCTION Pin ......................................................................... 15
RESETB: 58h<6:5> = 00b (Default)..................................... 32
STATUS Pin ................................................................................ 16
SYNCB: 58h<6:5> = 01b ....................................................... 32
Power............................................................................................ 16
PDB: 58h<6:5> = 11b ............................................................ 33
Timing Diagrams............................................................................ 17
Distribution Section................................................................... 33
Absolute Maximum Ratings.......................................................... 18
CLK1 and CLK2 Clock Inputs.................................................. 33
Thermal Characteristics ............................................................ 18
Dividers........................................................................................ 33
ESD Caution................................................................................ 18
Setting the Divide Ratio ........................................................ 33
Pin Configuration and Function Descriptions........................... 19
Setting the Duty Cycle........................................................... 33
Terminology .................................................................................... 21
Divider Phase Offset.............................................................. 37
Typical Performance Characteristics ........................................... 22
Delay Block ................................................................................. 38
Typical Modes of Operation.......................................................... 26
Calculating the Delay ............................................................ 38
PLL with External VCXO/VCO Followed by Clock
Distribution................................................................................. 26
Outputs ........................................................................................ 38
Power-Down Modes .................................................................. 39
Clock Distribution Only............................................................ 26
Chip Power-Down or Sleep Mode—PDB........................... 39
PLL with External VCO and Band-Pass Filter Followed by
Clock Distribution...................................................................... 27
PLL Power-Down................................................................... 39
Functional Description .................................................................. 29
Distribution Power-Down .................................................... 39
Overall.......................................................................................... 29
Individual Clock Output Power-Down............................... 39
PLL Section ................................................................................. 29
Individual Circuit Block Power-Down................................ 39
PLL Reference Input—REFIN .............................................. 29
Reset Modes ................................................................................ 40
VCO/VCXO Clock Input—CLK2........................................ 29
Power-On Reset—Start-Up Conditions when VS
is Applied................................................................................. 40
PLL Reference Divider—R .................................................... 29
VCO/VCXO Feedback Divider—N (P, A, B) ..................... 29
Rev. A | Page 2 of 60
Asynchronous Reset via the FUNCTION Pin ................... 40
Soft Reset via the Serial Port................................................. 40
AD9511
Single-Chip Synchronization.....................................................40
Summary Table............................................................................45
SYNCB—Hardware SYNC ....................................................40
Register Map Description ..........................................................47
Soft SYNC—Register 58h<2> ...............................................40
Power Supply ...................................................................................54
Multichip Synchronization ........................................................40
Power Management ....................................................................54
Serial Control Port ..........................................................................41
Applications .....................................................................................55
Serial Control Port Pin Descriptions........................................41
Using the AD9511 Outputs for ADC Clock Applications ....55
General Operation of Serial Control Port ...............................41
CMOS Clock Distribution.........................................................55
Framing a Communication Cycle with CSB .......................41
LVPECL Clock Distribution......................................................56
Communication Cycle—Instruction Plus Data..................41
LVDS Clock Distribution...........................................................56
Write .........................................................................................41
Power and Grounding Considerations and Power Supply
Rejection.......................................................................................56
Read ..........................................................................................42
The Instruction Word (16 Bits).................................................42
MSB/LSB First Transfers ............................................................42
Outline Dimensions........................................................................57
Ordering Guide ...........................................................................57
Register Map and Description.......................................................45
REVISION HISTORY
6/05—Rev. 0 to Rev. A
Changes to Features ..........................................................................1
Changes to General Description .....................................................1
Changes to Table 1 and Table 2 .......................................................5
Changes to Table 4 ............................................................................7
Changes to Table 5 ............................................................................9
Changes to Table 6 ..........................................................................14
Changes to Table 8 and Table 9 .....................................................15
Changes to Table 11 ........................................................................16
Changes to Table 13 ........................................................................20
Changes to Figure 19 to Figure 23 ................................................24
Changes to Figure 30 and Figure 31 .............................................26
Changes to Figure 32 ......................................................................27
Changes to Figure 33 ......................................................................28
Changes to VCO/VCXO Clock Input—CLK2 Section ..............29
Changes to PLL Reference Divider—P Section...........................29
Changes to A and B Counters Section .........................................30
Changes to PLL Digital Lock Detect Section ..............................31
Changes to PLL Analog Lock Detect Section..............................32
Changes to Loss of Reference Section ..........................................32
Changes to FUNCTION Pin Section ...........................................32
Changes to RESETB: 58h<6:5> = 00b (Default) Section ...........32
Changes to SYNCB: 58h<6:5> = 01b Section..............................32
Changes to CLK1 and CLK2 Clock Inputs Section....................33
Changes to Divider Phase Offset Section ....................................37
Changes to Individual Clock Output Power-Down Section .....39
Changes to Individual Circuit Block Power-Down Section......39
Changes to Soft Reset via the Serial Port Section .......................40
Changes to Multichip Synchronization Section..........................40
Changes to Serial Control Port Section .......................................41
Changes to Serial Control Port Pin Descriptions Section .........41
Changes to General Operation of Serial
Control Port Section .......................................................................41
Added Framing a Communication Cycle with CSB Section ....41
Added Communication Cycle—Instruction Plus
Data Section.....................................................................................41
Changes to Write Section...............................................................41
Changes to Read Section................................................................42
Changes to Instruction Word (16 Bits) Section ..........................42
Changes to Table 20 ........................................................................42
Changes to MSB/LSB First Transfers Section..............................42
Added Figure 52; Renumbered Sequentially...............................44
Changes to Table 23 ........................................................................45
Changes to Table 24 ........................................................................47
Changes to Power Supply...............................................................54
4/05—Revision 0: Initial Version
Rev. A | Page 3 of 60
AD9511
SPECIFICATIONS
Typical (typ) is given for VS = 3.3 V ± 5%; VS ≤ VCPS ≤ 5.5 V, TA = 25°C, RSET = 4.12 kΩ, CPRSET = 5.1 kΩ, unless otherwise noted.
Minimum (min) and maximum (max) values are given over full VS and TA (−40°C to +85°C) variation.
PLL CHARACTERISTICS
Table 1.
Parameter
REFERENCE INPUTS (REFIN)
Input Frequency
Input Sensitivity
Self-Bias Voltage, REFIN
Self-Bias Voltage, REFINB
Input Resistance, REFIN
Input Resistance, REFINB
Input Capacitance
PHASE/FREQUENCY DETECTOR (PFD)
PFD Input Frequency
PFD Input Frequency
PFD Input Frequency
Antibacklash Pulse Width
Antibacklash Pulse Width
Antibacklash Pulse Width
CHARGE PUMP (CP)
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
CPRSET Range
ICP Three-State Leakage
Sink-and-Source Current Matching
ICP vs. VCP
ICP vs. Temperature
RF CHARACTERISTICS (CLK2) 2
Input Frequency
Input Sensitivity
Input Common-Mode Voltage, VCM
Input Common-Mode Range, VCMR
Input Sensitivity, Single-Ended
Input Resistance
Input Capacitance
CLK2 VS. REFIN DELAY
PRESCALER (PART OF N DIVIDER)
Prescaler Input Frequency
P = 2 DM (2/3)
P = 4 DM (4/5)
P = 8 DM (8/9)
P = 16 DM (16/17)
P = 32 DM (32/33)
CLK2 Input Frequency for PLL
Min
Typ
0
1.45
1.40
4.0
4.5
150
1.60
1.50
4.9
5.4
2
Max
Unit
250
MHz
mV p-p
V
V
kΩ
kΩ
pF
1.75
1.60
5.8
6.3
100
100
45
1.5
1.3
1.3
2.9
6.0
MHz
MHz
MHz
ns
ns
ns
4.8
0.60
2.5
2.7/10
1
2
1.5
2
mA
mA
%
kΩ
nA
%
%
%
150
1.6
1.6
GHz
1.7
1.8
mV p-p
V
V
mV p-p
150
4.0
4.8
2
500
5.6
600
1000
1600
1600
1600
300
kΩ
pF
ps
MHz
MHz
MHz
MHz
MHz
MHz
Rev. A | Page 4 of 60
Test Conditions/Comments
Self-bias voltage of REFIN 1 .
Self-bias voltage of REFINB1.
Self-biased1.
Self-biased1.
Antibacklash pulse width 0Dh<1:0> = 00b.
Antibacklash pulse width 0Dh<1:0> = 01b.
Antibacklash pulse width 0Dh<1:0> = 10b.
0Dh<1:0> = 00b. (This is the default setting.)
0Dh<1:0> = 01b.
0Dh<1:0> = 10b.
Programmable.
With CPRSET = 5.1 kΩ.
VCP = VCPS/2.
0.5 < VCP < VCPS − 0.5 V.
0.5 < VCP < VCPS − 0.5 V.
VCP = VCPS/2 V.
Frequencies > 1200 MHz (LVPECL) or
800 MHz (LVDS) require a minimum
divide-by-2 (see the Distribution Section).
Self-biased; enables ac coupling.
With 200 mV p-p signal applied.
CLK2 ac-coupled; CLK2B capacitively
bypassed to RF ground.
Self-biased.
Difference at PFD.
See the VCO/VCXO Feedback Divider—N (P, A, B)
section.
A, B counter input frequency.
AD9511
Parameter
NOISE CHARACTERISTICS
In-Band Noise of the Charge Pump/
Phase Frequency Detector (In-Band
Means Within the LBW of the PLL)
Min
Typ
Max
Unit
Test Conditions/Comments
The synthesizer phase noise floor is
estimated by measuring the in-band
phase noise at the output of the VCO and
subtracting 20logN (where N is the
N divider value).
@ 50 kHz PFD Frequency
@ 2 MHz PFD Frequency
@ 10 MHz PFD Frequency
@ 50 MHz PFD Frequency
PLL Figure of Merit
−172
−156
−149
−142
−218 +
10 × log (fPFD)
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
3.5
7.5
3.5
ns
ns
ns
7
15
11
ns
ns
ns
PLL DIGITAL LOCK DETECT WINDOW 4
Required to Lock
(Coincidence of Edges)
Low Range (ABP 1.3 ns, 2.9 ns Only)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
To Unlock After Lock (Hysteresis)4
Low Range (ABP 1.3 ns, 2.9 ns Only)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
Approximation of the PFD/CP phase noise
floor (in the flat region) inside the PLL loop
bandwidth. When running closed loop this
phase noise is gained up by 20 × log(N) 3 .
Signal available at STATUS pin
when selected by 08h<5:2>.
Selected by Register ODh.
<5> = 1b.
<5> = 0b.
<5> = 0b.
Selected by Register 0Dh.
<5> = 1b.
<5> = 0b.
<5> = 0b.
1
REFIN and REFINB self-bias points are offset slightly to avoid chatter on an open input condition.
CLK2 is electrically identical to CLK1; the distribution only input can be used as differential or single-ended input (see the Clock Inputs section).
3
Example: −218 + 10 × log(fPFD) + 20 × log(N) should give the values for the in-band noise at the VCO output.
4
For reliable operation of the digital lock detect, the period of the PFD frequency must be greater than the unlock-after-lock time.
2
CLOCK INPUTS
Table 2.
Parameter
CLOCK INPUTS (CLK1, CLK2) 1
Input Frequency
Input Sensitivity
Min
Typ
0
Unit
1.6
GHz
mV p-p
150 2
Input Level
Input Common-Mode Voltage, VCM
Input Common-Mode Range, VCMR
Input Sensitivity, Single-Ended
Input Resistance
Input Capacitance
Max
1.5
1.3
4.0
1.6
150
4.8
2
23
V p-p
1.7
1.8
V
V
mV p-p
kΩ
pF
5.6
1
Test Conditions/Comments
Jitter performance can be improved with higher slew
rates (greater swing).
Larger swings turn on the protection diodes and can
degrade jitter performance.
Self-biased; enables ac coupling.
With 200 mV p-p signal applied; dc-coupled.
CLK2 ac-coupled; CLK2B ac bypassed to RF ground.
Self-biased.
CLK1 and CLK2 are electrically identical; each can be used as either differential or single-ended input.
With a 50 Ω termination, this is −12.5 dBm.
3
With a 50 Ω termination, this is +10 dBm.
2
Rev. A | Page 5 of 60
AD9511
CLOCK OUTPUTS
Table 3.
Parameter
LVPECL CLOCK OUTPUTS
OUT0, OUT1, OUT2; Differential
Output Frequency
Output High Voltage (VOH)
Output Low Voltage (VOL)
Output Differential Voltage (VOD)
LVDS CLOCK OUTPUTS
OUT3, OUT4; Differential
Output Frequency
Differential Output Voltage (VOD)
Delta VOD
Output Offset Voltage (VOS)
Delta VOS
Short-Circuit Current (ISA, ISB)
CMOS CLOCK OUTPUTS
OUT3, OUT4
Output Frequency
Output Voltage High (VOH)
Output Voltage Low (VOL)
Min
Typ
Max
Unit
VS − 1.22
VS − 2.10
660
VS − 0.98
VS − 1.80
810
1200
VS − 0.93
VS − 1.67
965
MHz
V
V
mV
250
360
1.125
1.23
14
800
450
25
1.375
25
24
250
VS-0.1
0.1
Rev. A | Page 6 of 60
MHz
mV
mV
V
mV
mA
MHz
V
V
Test Conditions/Comments
Termination = 50 Ω to VS − 2 V
Output level 3Dh (3Eh) (3Fh)<3:2> = 10b
See Figure 21
Termination = 100 Ω differential; default
Output level 40h (41h)<2:1> = 01b
3.5 mA termination current
See Figure 22
Output shorted to GND
Single-ended measurements;
B outputs: inverted, termination open
With 5 pF load each output; see Figure 23
@ 1 mA load
@ 1 mA load
AD9511
TIMING CHARACTERISTICS
Table 4.
Parameter
LVPECL
Output Rise Time, tRP
Output Fall Time, tFP
PROPAGATION DELAY, tPECL, CLK-TO-LVPECL OUT 1
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, LVPECL OUTPUTS
OUT1 to OUT0 on Same Part, tSKP 2
OUT1 to OUT2 on Same Part, tSKP2
OUT0 to OUT2 on Same Part, tSKP2
All LVPECL OUT Across Multiple Parts, tSKP_AB 3
Same LVPECL OUT Across Multiple Parts, tSKP_AB3
LVDS
Output Rise Time, tRL
Output Fall Time, tFL
PROPAGATION DELAY, tLVDS, CLK-TO-LVDS OUT1
OUT3 to OUT4
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, LVDS OUTPUTS
OUT3 to OUT4 on Same Part, tSKV2
All LVDS OUTs Across Multiple Parts, tSKV_AB3
Same LVDS OUT Across Multiple Parts, tSKV_AB3
CMOS
Output Rise Time, tRC
Output Fall Time, tFC
PROPAGATION DELAY, tCMOS, CLK-TO-CMOS OUT1
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, CMOS OUTPUTS
OUT3 to OUT4 on Same Part, tSKC2
All CMOS OUT Across Multiple Parts, tSKC_AB3
Same CMOS OUT Across Multiple Parts, tSKC_AB3
LVPECL-TO-LVDS OUT
Output Skew, tSKP_V
LVPECL-TO-CMOS OUT
Output Skew, tSKP_C
LVDS-TO-CMOS OUT
Output Skew, tSKV_C
Min
Typ
Max
Unit
130
130
180
180
ps
ps
335
375
490
545
0.5
635
695
ps
ps
ps/°C
70
15
45
100
45
65
140
80
90
275
130
ps
ps
Ps
ps
ps
200
210
350
350
ps
ps
1.33
1.38
0.9
1.59
1.64
ns
ns
ps/°C
+270
450
325
ps
ps
ps
681
646
865
992
ps
ps
1.02
1.07
1.39
1.44
1
1.71
1.76
ns
ns
ps/°C
−140
+145
+300
650
500
ps
ps
0.99
1.04
Test Conditions/Comments
Termination = 50 Ω to VS − 2 V
Output level 3Dh (3Eh) (3Fh)<3:2> = 10b
20% to 80%, measured differentially
80% to 20%, measured differentially
Termination = 100 Ω differential
Output level 40h (41h) <2:1> = 01b
3.5 mA termination current
20% to 80%, measured differentially
80% to 20%, measured differentially
Delay off on OUT4
Delay off on OUT4
−85
B outputs are inverted; termination = open
20% to 80%; CLOAD = 3 pF
80% to 20%; CLOAD = 3 pF
Delay off on OUT4
Delay off on OUT4
0.74
0.92
1.14
ns
0.88
1.14
1.43
ns
158
353
506
ps
Rev. A | Page 7 of 60
Everything the same; different logic type
LVPECL to LVDS on same part
Everything the same; different logic type
LVPECL to CMOS on same part
Everything the same; different logic type
LVDS to CMOS on same part
AD9511
Parameter
DELAY ADJUST
Shortest Delay Range 4
Zero Scale
Full Scale
Linearity, DNL
Linearity, INL
Longest Delay Range4
Zero Scale
Full Scale
Linearity, DNL
Linearity, INL
Delay Variation with Temperature
Long Delay Range, 10 ns 5
Zero Scale
Full Scale
Short Delay Range, 1 ns5
Zero Scale
Full Scale
Min
Typ
Max
Unit
0.05
0.72
0.36
1.12
0.5
0.8
0.68
1.51
ns
ns
LSB
LSB
0.20
9.0
0.57
10.2
0.3
0.6
0.95
11.6
ns
ns
LSB
LSB
0.35
−0.14
ps/°C
ps/°C
0.51
0.67
ps/°C
ps/°C
1
Test Conditions/Comments
OUT4; LVDS and CMOS
35h <5:1> 11111b
36h <5:1> 00000b
36h <5:1> 11111b
35h <5:1> 00000b
36h <5:1> 00000b
36h <5:1> 11111b
The measurements are for CLK1. For CLK2, add approximately 25 ps.
This is the difference between any two similar delay paths within a single device operating at the same voltage and temperature.
3
This is the difference between any two similar delay paths across multiple devices operating at the same voltage and temperature.
4
Incremental delay; does not include propagation delay.
5
All delays between zero scale and full scale can be estimated by linear interpolation.
2
Rev. A | Page 8 of 60
AD9511
CLOCK OUTPUT PHASE NOISE
Table 5.
Parameter
CLK1-TO-LVPECL ADDITIVE PHASE NOISE
CLK1 = 622.08 MHz, OUT = 622.08 MHz
Divide Ratio = 1
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
CLK1 = 622.08 MHz, OUT = 155.52 MHz
Divide Ratio = 4
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
CLK1 = 622.08 MHz, OUT = 38.88 MHz
Divide Ratio = 16
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
CLK1 = 491.52 MHz, OUT = 61.44 MHz
Divide Ratio = 8
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
CLK1 = 491.52 MHz, OUT = 245.76 MHz
Divide Ratio = 2
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
CLK1 = 245.76 MHz, OUT = 61.44 MHz
Divide Ratio = 4
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
Min
Typ
Max
Unit
−125
−132
−140
−148
−153
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−128
−140
−148
−155
−161
−161
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−135
−145
−158
−165
−165
−166
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−131
−142
−153
−160
−165
−165
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−125
−132
−140
−151
−157
−158
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−138
−144
−154
−163
−164
−165
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. A | Page 9 of 60
Test Conditions/Comments
Distribution Section only; does not
include PLL or external VCO/VCXO
Input slew rate > 1 V/ns
AD9511
Parameter
CLK1-TO-LVDS ADDITIVE PHASE NOISE
CLK1 = 622.08 MHz, OUT= 622.08 MHz
Divide Ratio = 1
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 622.08 MHz, OUT = 155.52 MHz
Divide Ratio = 4
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 491.52 MHz, OUT = 245.76 MHz
Divide Ratio = 2
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 491.52 MHz, OUT = 122.88 MHz
Divide Ratio = 4
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 245.76 MHz, OUT = 245.76 MHz
Divide Ratio = 1
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 245.76 MHz, OUT = 122.88 MHz
Divide Ratio = 2
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
Min
Typ
Max
Unit
−100
−110
−118
−129
−135
−140
−148
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−112
−122
−132
−142
−148
−152
−155
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−108
−118
−128
−138
−145
−148
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−118
−129
−136
−147
−153
−156
−158
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−108
−118
−128
−138
−145
−148
−155
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−118
−127
−137
−147
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. A | Page 10 of 60
Test Conditions/Comments
Distribution Section only; does not
include PLL or external VCO/VCXO
AD9511
Parameter
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1-TO-CMOS ADDITIVE PHASE NOISE
CLK1 = 245.76 MHz, OUT = 245.76 MHz
Divide Ratio = 1
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
> 10 MHz Offset
CLK1 = 245.76 MHz, OUT = 61.44 MHz
Divide Ratio = 4
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 78.6432 MHz, OUT = 78.6432 MHz
Divide Ratio = 1
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
>10 MHz Offset
CLK1 = 78.6432 MHz, OUT = 39.3216 MHz
Divide Ratio = 2
@ 10 Hz Offset
@ 100 Hz Offset
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
>1 MHz Offset
Min
Typ
−154
−156
−158
Max
Unit
dBc/Hz
dBc/Hz
dBc/Hz
Test Conditions/Comments
Distribution Section only; does not
include PLL or external VCO/VCXO
−110
−121
−130
−140
−145
−149
−156
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−122
−132
−143
−152
−158
−160
−162
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−122
−132
−140
−150
−155
−158
−160
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−128
−136
−146
−155
−161
−162
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. A | Page 11 of 60
AD9511
CLOCK OUTPUT ADDITIVE TIME JITTER
Table 6.
Parameter
LVPECL OUTPUT ADDITIVE TIME JITTER
CLK1 = 622.08 MHz
Any LVPECL (OUT0 to OUT2) = 622.08 MHz
Divide Ratio = 1
CLK1 = 622.08 MHz
Any LVPECL (OUT0 to OUT2) = 155.52 MHz
Divide Ratio = 4
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT2) = 100 MHz
Divide Ratio = 4
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT2) = 100 MHz
Divide Ratio = 4
Other LVPECL = 100 MHz
Both LVDS (OUT3, OUT4) = 100 MHz
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT2) = 100 MHz
Divide Ratio = 4
Other LVPECL = 50 MHz
Both LVDS (OUT3, OUT4) = 50 MHz
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT2) = 100 MHz
Divide Ratio = 4
Other LVPECL = 50 MHz
Both CMOS (OUT3, OUT4) = 50 MHz (B Outputs Off)
CLK1 = 400 MHz
Min
Typ
Max
40
fs rms
Test Conditions/Comments
Distribution Section only; does not
include PLL or external VCO/VCXO
BW = 12 kHz − 20 MHz (OC-12)
55
fs rms
BW = 12 kHz − 20 MHz (OC-3)
215
fs rms
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
215
fs rms
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
222
225
225
Unit
fs rms
fs rms
fs rms
Any LVPECL (OUT0 to OUT2) = 100 MHz
Divide Ratio = 4
Other LVPECL = 50 MHz
Both CMOS (OUT3, OUT4) = 50 MHz (B Outputs On)
LVDS OUTPUT ADDITIVE TIME JITTER
CLK1 = 400 MHz
264
fs rms
LVDS (OUT3) = 100 MHz
Divide Ratio = 4
CLK1 = 400 MHz
319
fs rms
LVDS (OUT4) = 100 MHz
Divide Ratio = 4
Rev. A | Page 12 of 60
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Distribution Section only; does not
include PLL or external VCO/VCXO
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
AD9511
Parameter
CLK1 = 400 MHz
LVDS (OUT3) = 100 MHz
Divide Ratio = 4
LVDS (OUT4) = 50 MHz
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT4) = 100 MHz
Divide Ratio = 4
LVDS (OUT3) = 50 MHz
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT3) = 100 MHz
Divide Ratio = 4
CMOS (OUT4) = 50 MHz (B Outputs Off)
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT4) = 100 MHz
Divide Ratio = 4
CMOS (OUT3) = 50 MHz (B Outputs Off)
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT3) = 100 MHz
Divide Ratio = 4
CMOS (OUT4) = 50 MHz (B Outputs On)
All LVPECL = 50 MHz
CLK1 = 400 MHz
Min
Typ
395
Max
395
367
367
548
548
Unit
fs rms
fs rms
fs rms
fs rms
fs rms
fs rms
LVDS (OUT4) = 100 MHz
Divide Ratio = 4
CMOS (OUT3) = 50 MHz (B Outputs On)
All LVPECL = 50 MHz
CMOS OUTPUT ADDITIVE TIME JITTER
CLK1 = 400 MHz
275
fs rms
Both CMOS (OUT3, OUT4) = 100 MHz (B Output On)
Divide Ratio = 4
CLK1 = 400 MHz
400
fs rms
CMOS (OUT3) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
LVDS (OUT4) = 50 MHz
CLK1 = 400 MHz
374
CMOS (OUT3) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
CMOS (OUT4) = 50 MHz (B Output Off)
fs rms
Test Conditions/Comments
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Distribution Section only;
does not include PLL or external VCO/VCXO
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Rev. A | Page 13 of 60
AD9511
Parameter
CLK1 = 400 MHz
Min
CMOS (OUT3) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
CMOS (OUT4) = 50 MHz (B Output On)
DELAY BLOCK ADDITIVE TIME JITTER 1
100 MHz Output
Delay FS = 1 ns (1600 μA, 1C) Fine Adj. 00000
Delay FS = 1 ns (1600 μA, 1C) Fine Adj. 11111
Delay FS = 2 ns (800 μA, 1C) Fine Adj. 00000
Delay FS = 2 ns (800 μA, 1C) Fine Adj. 11111
Delay FS = 3 ns (800 μA, 4C) Fine Adj. 00000
Delay FS = 3 ns (800 μA, 4C) Fine Adj. 11111
Delay FS = 4 ns (400 μA, 4C) Fine Adj. 00000
Delay FS = 4 ns (400 μA, 4C) Fine Adj. 11111
Delay FS = 5 ns (200 μA, 1C) Fine Adj. 00000
Delay FS = 5 ns (200 μA, 1C) Fine Adj. 11111
Delay FS = 11 ns (200 μA, 4C) Fine Adj. 00000
Delay FS = 11 ns (200 μA, 4C) Fine Adj. 00100
1
Typ
555
Max
Unit
fs rms
Test Conditions/Comments
Calculated from SNR of ADC method;
FC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Incremental additive jitter
0.61
0.73
0.71
1.2
0.86
1.8
1.2
2.1
1.3
2.7
2.0
2.8
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
This value is incremental. That is, it is in addition to the jitter of the LVDS or CMOS output without the delay. To estimate the total jitter, the LVDS or CMOS output jitter
should be added to this value using the root sum of the squares (RSS) method.
PLL AND DISTRIBUTION PHASE NOISE AND SPURIOUS
Table 7.
Parameter
PHASE NOISE AND SPURIOUS
Min
Typ
Max
Unit
VCXO = 245.76 MHz,
FPFD = 1.2288 MHz; R = 25, N = 200
245.76 MHz Output
Phase Noise @100 kHz Offset
Spurious
<−145
<−97
dBc/Hz
dBc
61.44 MHz Output
Phase Noise @100 kHz Offset
Spurious
<−155
<−97
dBc/Hz
dBc
Rev. A | Page 14 of 60
Test Conditions/Comments
Depends on VCO/VCXO selection. Measured at LVPECL
clock outputs; ABP = 6 ns; ICP = 5 mA; Ref = 30.72 MHz.
VCXO is Toyocom TCO-2112 245.76.
Divide by 1.
Dominated by VCXO phase noise.
First and second harmonics of FPFD.
Below measurement floor.
Divide by 4.
Dominated by VCXO phase noise.
First and second harmonics of FPFD.
Below measurement floor.
AD9511
SERIAL CONTROL PORT
Table 8.
Parameter
CSB, SCLK (INPUTS)
Min
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO (WHEN INPUT)
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO, SDO (OUTPUTS)
Output Logic 1 Voltage
Output Logic 0 Voltage
TIMING
Clock Rate (SCLK, 1/tSCLK)
Pulse Width High, tPWH
Pulse Width Low, tPWL
SDIO to SCLK Setup, tDS
SCLK to SDIO Hold, tDH
SCLK to Valid SDIO and SDO, tDV
CSB to SCLK Setup and Hold, tS, tH
CSB Minimum Pulse Width High, tPWH
2.0
Typ
Max
0.8
110
1
2
2.0
0.8
10
10
2
2.7
0.4
25
16
16
2
1
6
2
3
Unit
Test Conditions/Comments
CSB and SCLK have 30 kΩ
internal pull-down resistors
V
V
μA
μA
pF
V
V
nA
nA
pF
V
V
MHz
ns
ns
ns
ns
ns
ns
ns
FUNCTION PIN
Table 9.
Parameter
INPUT CHARACTERISTICS
Min
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Capacitance
RESET TIMING
Pulse Width Low
SYNC TIMING
Pulse Width Low
2.0
Typ
Max
0.8
110
1
2
Unit
Test Conditions/Comments
The FUNCTION pin has a 30 kΩ internal pull-down resistor.
This pin should normally be held high. Do not leave NC.
V
V
μA
μA
pF
50
ns
1.5
High speed clock cycles
Rev. A | Page 15 of 60
High speed clock is CLK1 or CLK2, whichever is
used for distribution.
AD9511
STATUS PIN
Table 10.
Parameter
OUTPUT CHARACTERISTICS
Min
Output Voltage High (VOH)
Output Voltage Low (VOL)
MAXIMUM TOGGLE RATE
2.7
ANALOG LOCK DETECT
Capacitance
Typ
Max
Unit
0.4
100
V
V
MHz
3
pF
Test Conditions/Comments
When selected as a digital output (CMOS); there are other modes
in which the STATUS pin is not CMOS digital output. See Figure 37.
Applies when PLL mux is set to any divider or counter output,
or PFD up/down pulse. Also applies in analog lock detect mode.
Usually debug mode only. Beware that spurs may couple
to output when this pin is toggling.
On-chip capacitance; used to calculate RC time
constant for analog lock detect readback. Use a pull-up resistor.
POWER
Table 11.
Parameter
POWER-UP DEFAULT MODE POWER DISSIPATION
Min
Typ
550
POWER DISSIPATION
Max
600
Unit
mW
800
mW
850
mW
Full Sleep Power-Down
35
60
mW
Power-Down (PDB)
60
80
mW
POWER DELTA
CLK1, CLK2 Power-Down
Divider, DIV 2 − 32 to Bypass
LVPECL Output Power-Down (PD2, PD3)
10
23
50
15
27
65
25
33
75
mW
mW
mW
LVDS Output Power-Down
CMOS Output Power-Down (Static)
CMOS Output Power-Down (Dynamic)
80
56
115
92
70
150
110
85
190
mW
mW
mW
CMOS Output Power-Down (Dynamic)
125
165
210
mW
Delay Block Bypass
20
24
60
mW
PLL Section Power-Down
5
15
40
mW
Rev. A | Page 16 of 60
Test Conditions/Comments
Power-up default state; does not include power
dissipated in output load resistors. No clock.
All outputs on. Three LVPECL outputs @ 800 MHz,
two CMOS out @ 62 MHz (5 pF load). Does not include
power dissipated in external resistors.
All outputs on. Three LVPECL outputs @ 800 MHz,
two CMOS out @ 125 MHz (5 pF load). Does not include
power dissipated in external resistors.
Maximum sleep is entered by setting 0Ah<1:0> = 01b
and 58h<4> = 1b. This powers off the PLL BG and the
distribution BG references. Does not include power
dissipated in terminations.
Set FUNCTION pin for PDB operation by setting
58h<6:5> = 11b. Pull PDB low. Does not include
power dissipated in terminations.
For each divider.
For each output. Does not include dissipation
in termination (PD2 only).
For each output.
For each output. Static (no clock).
For each CMOS output, single-ended. Clocking at
62 MHz with 5 pF load.
For each CMOS output, single-ended. Clocking at
125 MHz with 5 pF load.
Vs. delay block operation at 1 ns fs with maximum
delay; output clocking at 25 MHz.
AD9511
TIMING DIAGRAMS
tCLK1
CLK1
DIFFERENTIAL
tPECL
80%
LVDS
tLVDS
tCMOS
tRL
tFL
05286-065
05286-002
20%
Figure 4. LVDS Timing, Differential
Figure 2. CLK1/CLK1B to Clock Output Timing, DIV = 1 Mode
SINGLE-ENDED
DIFFERENTIAL
80%
80%
CMOS
3pF LOAD
LVPECL
tFP
05286-064
tRP
tRC
tFC
Figure 5. CMOS Timing, Single-Ended, 3 pF Load
Figure 3. LVPECL Timing, Differential
Rev. A | Page 17 of 60
05286-066
20%
20%
AD9511
ABSOLUTE MAXIMUM RATINGS
Table 12.
Parameter or Pin
VS
VCP
VCP
REFIN, REFINB
RSET
CPRSET
CLK1, CLK1B, CLK2, CLK2B
CLK1
CLK2
SCLK, SDIO, SDO, CSB
OUT0, OUT1, OUT2, OUT3,
OUT4
FUNCTION
STATUS
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
With
Respect
to
GND
GND
VS
GND
GND
GND
GND
CLK1B
CLK2B
GND
GND
Min
−0.3
−0.3
−0.3
−0.3
−0.3
−0.3
−0.3
−1.2
−1.2
−0.3
−0.3
Max
+3.6
+5.8
+5.8
VS + 0.3
VS + 0.3
VS + 0.3
VS + 0.3
+1.2
+1.2
VS + 0.3
VS + 0.3
Unit
V
V
V
V
V
V
V
V
V
V
V
GND
GND
−0.3
−0.3
VS + 0.3
VS + 0.3
150
+150
300
V
V
°C
°C
°C
−65
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum ratings for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
Thermal Resistance 1
48-Lead LFCSP
θJA = 28.5°C/W
1
Thermal impedance measurements were taken on a 4-layer board in still air,
in accordance with EIA/JESD51-7.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 18 of 60
AD9511
48
47
46
45
44
43
42
41
40
39
38
37
VS
CPRSET
GND
RSET
VS
GND
OUT0
OUT0B
VS
VS
GND
GND
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
AD9511
TOP VIEW
(Not to Scale)
36
35
34
33
32
31
30
29
28
27
26
25
VS
OUT3
OUT3B
VS
VS
OUT4
OUT4B
VS
VS
OUT1
OUT1B
VS
05286-003
STATUS
SCLK
SDIO
SDO
CSB
VS
GND
OUT2B
OUT2
VS
VS
GND
13
14
15
16
17
18
19
20
21
22
23
24
REFIN 1
REFINB 2
VS 3
VCP 4
CP 5
VS 6
CLK2 7
CLK2B 8
VS 9
CLK1 10
CLK1B 11
FUNCTION 12
Figure 6. 48-Lead LFCSP Pin Configuration
Note that the exposed paddle on this package is an electrical connection as well as a thermal enhancement. For the device to
function properly, the paddle must be attached to ground, GND.
Rev. A | Page 19 of 60
AD9511
Table 13. Pin Function Descriptions
Pin No.
1
2
3, 6, 9, 18, 22,
23, 25, 28, 29,
32, 33, 36, 39,
40, 44, 48
4
Mnemonic
REFIN
REFINB
VS
Description
PLL Reference Input.
Complementary PLL Reference Input.
Power Supply (3.3 V).
VCP
5
7
CP
CLK2
8
10
11
12
CLK2B
CLK1
CLK1B
FUNCTION
13
14
15
16
17
19, 24, 37,
38, 43, 46
20
21
26
27
30
31
34
35
41
42
45
47
STATUS
SCLK
SDIO
SDO
CSB
GND
Charge Pump Power Supply. It should be greater than or equal to VS.
VCP can be set as high as 5.5 V for VCOs, requiring extended tuning range.
Charge Pump Output.
Clock Input. Used to connect external VCO/VCXO to feedback divider, N. CLK2 also drives the
distribution section of the chip and may be used as a generic clock input when PLL is not used.
Complementary Clock Input. Used in conjunction with CLK2.
Clock Input. Drives distribution section of the chip.
Complementary Clock Input. Used in conjunction with CLK1.
Multipurpose Input. May be programmed as a reset (RESETB), sync (SYNCB), or power-down (PDB) pin.
This pin is internally pulled down by a 30 kΩ resistor. If this pin is left NC, the part is in reset by default.
To avoid this, connect this pin to VS with a 1 kΩ resistor.
Output Used to Monitor PLL Status and Sync Status.
Serial Data Clock.
Serial Data I/O.
Serial Data Output.
Serial Port Chip Select.
Ground.
OUT2B
OUT2
OUT1B
OUT1
OUT4B
OUT4
OUT3B
OUT3
OUT0B
OUT0
RSET
CPRSET
Complementary LVPECL Output.
LVPECL Output.
Complementary LVPECL Output.
LVPECL Output.
Complementary LVDS/Inverted CMOS Output. OUT4 includes a delay block.
LVDS/CMOS Output. OUT4 includes a delay block.
Complementary LVDS/Inverted CMOS Output.
LVDS/CMOS Output.
Complementary LVPECL Output.
LVPECL Output.
Current Set Resistor to Ground. Nominal value = 4.12 kΩ.
Charge Pump Current Set Resistor to Ground. Nominal value = 5.1 kΩ.
Note that the exposed paddle on this package is an electrical connection as well as a thermal enhancement. For the device to
function properly, the paddle must be attached to ground, GND.
Rev. A | Page 20 of 60
AD9511
TERMINOLOGY
Phase Jitter and Phase Noise
An ideal sine wave can be thought of as having a continuous
and even progression of phase with time from 0 degrees to
360 degrees for each cycle. Actual signals, however, display a
certain amount of variation from ideal phase progression over
time. This phenomenon is called phase jitter. Although many
causes can contribute to phase jitter, one major cause is random
noise, which is characterized statistically as being Gaussian
(normal) in distribution.
This phase jitter leads to a spreading out of the energy of the
sine wave in the frequency domain, producing a continuous
power spectrum. This power spectrum is usually reported as a
series of values whose units are dBc/Hz at a given offset in
frequency from the sine wave (carrier). The value is a ratio
(expressed in dB) of the power contained within a 1 Hz
bandwidth with respect to the power at the carrier frequency.
For each measurement, the offset from the carrier frequency is
also given.
It is meaningful to integrate the total power contained within
some interval of offset frequencies (for example, 10 kHz to
10 MHz). This is called the integrated phase noise over that
frequency offset interval and can be readily related to the time
jitter due to the phase noise within that offset frequency
interval.
Phase noise has a detrimental effect on the performance of
ADCs, DACs, and RF mixers. It lowers the achievable dynamic
range of the converters and mixers, although they are affected
in somewhat different ways.
Time Jitter
Phase noise is a frequency domain phenomenon. In the time
domain, the same effect is exhibited as time jitter. When
observing a sine wave, the time of successive zero crossings is
seen to vary. In a square wave, the time jitter is seen as a
displacement of the edges from their ideal (regular) times of
occurrence. In both cases, the variations in timing from the
ideal are the time jitter. Since these variations are random in
nature, the time jitter is specified in units of seconds root mean
square (rms) or 1 sigma of the Gaussian distribution.
Time jitter that occurs on a sampling clock for a DAC or an
ADC decreases the SNR and dynamic range of the converter.
A sampling clock with the lowest possible jitter provides the
highest performance from a given converter.
Additive Phase Noise
It is the amount of phase noise that is attributable to the device
or subsystem being measured. The phase noise of any external
oscillators or clock sources has been subtracted. This makes it
possible to predict the degree to which the device impacts the
total system phase noise when used in conjunction with the
various oscillators and clock sources, each of which contribute
their own phase noise to the total. In many cases, the phase
noise of one element dominates the system phase noise.
Additive Time Jitter
It is the amount of time jitter that is attributable to the device
or subsystem being measured. The time jitter of any external
oscillators or clock sources has been subtracted. This makes it
possible to predict the degree to which the device will impact
the total system time jitter when used in conjunction with the
various oscillators and clock sources, each of which contribute
their own time jitter to the total. In many cases, the time jitter of
the external oscillators and clock sources dominates the system
time jitter.
Rev. A | Page 21 of 60
AD9511
TYPICAL PERFORMANCE CHARACTERISTICS
0.6
0.7
DEFAULT – 3 LVPECL + 2 LVDS (DIV ON)
POWER (W)
0.6
POWER (W)
0.5
3 LVPECL + 2 LVDS (DIV BYPASSED)
0.4
3 LVPECL + 2 CMOS (DIV ON)
0.5
0.3
0
400
OUTPUT FREQUENCY (MHz)
800
Figure 7. Power vs. Frequency—LVPECL, LVDS (PLL Off)
05286-081
2 LVDS (DIV ON)
05286-080
3 LVPECL (DIV ON)
0.4
0
20
100
120
Figure 10. Power vs. Frequency—LVPECL, CMOS (PLL Off)
CLK1 (EVAL BOARD)
3GHz
40
60
80
OUTPUT FREQUENCY (MHz)
REFIN (EVAL BOARD)
5MHz
5GHz
05286-062
05286-043
3GHz
Figure 8. CLK1 Smith Chart (Evaluation Board)
Figure 11. REFIN Smith Chart (Evaluation Board)
CLK2 (EVAL BOARD)
5MHz
05286-044
3GHz
Figure 9. CLK2 Smith Chart (Evaluation Board)
Rev. A | Page 22 of 60
10
0
0
–10
–10
–20
–20
–30
–30
–40
–40
–50
–50
–60
–60
–70
–70
05286-058
10
–80
–90
CENTER 245.75MHz
30kHz/
–80
–90
CENTER 61.44MHz
SPAN 300kHz
30kHz/
SPAN 300kHz
Figure 15. Phase Noise, LVPECL, DIV 4, FVCXO = 245.76 MHz,
FOUT = 61.44 MHz, FPFD = 1.2288 MHz, R = 25, N = 200
Figure 12. Phase Noise, LVPECL, DIV 1, FVCXO = 245.76 MHz,
FOUT = 245.76 MHz, FPFD = 1.2288 MHz, R = 25, N = 200
–20
–30
–40
–50
–60
–70
05286-063
–80
–90
100
250kHz/
–145
–150
–155
–160
–165
–170
0.1
SPAN 2.5MHz
Figure 13. PLL Reference Spurs: VCO 1.5 GHz, FPFD = 1 MHz
4.5
4.5
4.0
4.0
CURRENT FROM CP PIN (mA)
5.0
3.5
PUMP UP
3.0
2.5
2.0
1.5
05286-041
1.0
0.5
0
0
0.5
1.0
1.5
2.0
VOLTAGE ON CP PIN (V)
2.5
100
Figure 16. Phase Noise (Referred to CP Output) vs. PFD Frequency
5.0
PUMP DOWN
1
10
PFD FREQUENCY (MHz)
3.0
3.5
PUMP DOWN
2.5
2.0
1.5
1.0
0.5
0
0
Figure 14. Charge Pump Output Characteristics @ VCPS = 3.3 V
PUMP UP
3.0
05286-042
CENTER 1.5GHz
–140
05286-057
–10
PFD NOISE REFERRED TO PFD INPUT (dBc/Hz)
–135
0
CURRENT FROM CP PIN (mA)
05286-059
AD9511
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOLTAGE ON CP PIN (V)
4.0
4.5
Figure 17. Charge Pump Output Characteristics @ VCPS = 5.0 V
Rev. A | Page 23 of 60
5.0
AD9511
DIFFERENTIAL SWING (V p-p)
1.8
1.7
1.6
1.5
1.4
VERT 500mV/DIV
05286-056
05286-053
1.3
1.2
100
HORIZ 500ps/DIV
600
1100
1600
OUTPUT FREQUENCY (MHz)
Figure 18. LVPECL Differential Output @ 800 MHz
Figure 21. LVPECL Differential Output Swing vs. Frequency
VERT 100mV/DIV
700
650
600
550
500
100
HORIZ 500ps/DIV
05286-050
05286-054
DIFFERENTIAL SWING (mV p-p)
750
300
500
700
900
OUTPUT FREQUENCY (MHz)
Figure 19. LVDS Differential Output @ 800 MHz
Figure 22. LVDS Differential Output Swing vs. Frequency
3.5
2pF
3.0
OUTPUT (VPK)
2.5
10pF
2.0
1.5
1.0
VERT 500mV/DIV
05286-047
05286-055
20pF
0.5
0
HORIZ 1ns/DIV
0
100
200
300
400
500
600
OUTPUT FREQUENCY (MHz)
Figure 20. CMOS Single-Ended Output @ 250 MHz with 10 pF Load
Figure 23. CMOS Single-Ended Output Swing vs. Frequency and Load
Rev. A | Page 24 of 60
–110
–120
–120
–130
–130
–140
–140
–150
–150
–160
–160
1k
10k
100k
OFFSET (Hz)
1M
–170
10
10M
–80
–90
–90
–100
–100
–110
–110
L(f) (dBc/Hz)
–80
–120
–130
–150
–150
–160
1k
10k
100k
OFFSET (Hz)
1M
–170
10
10M
–110
–120
–120
L(f) (dBc/Hz)
–110
–130
–140
–160
–160
1M
10k
100k
OFFSET (Hz)
1M
10M
–140
–150
10k
100k
OFFSET (Hz)
1k
–130
–150
05286-045
L(f) (dBc/Hz)
–100
1k
100
Figure 28. Additive Phase Noise—LVDS DIV2, 122.88 MHz
–100
100
10M
–160
Figure 25. Additive Phase Noise—LVDS DIV1, 245.76 MHz
–170
10
1M
–130
–140
100
10k
100k
OFFSET (Hz)
–120
–140
–170
10
1k
Figure 27. Additive Phase Noise—LVPECL DIV1, 622.08 MHz
05286-048
L(f) (dBc/Hz)
Figure 24. Additive Phase Noise—LVPECL DIV1, 245.76 MHz
Distribution Section Only
100
05286-049
100
10M
–170
10
Figure 26. Additive Phase Noise—CMOS DIV1, 245.76 MHz
05286-046
–170
10
05286-052
L(f) (dBc/Hz)
–110
05286-051
L(f) (dBc/Hz)
AD9511
100
1k
10k
100k
OFFSET (Hz)
1M
Figure 29. Additive Phase Noise—CMOS DIV4, 61.44 MHz
Rev. A | Page 25 of 60
10M
AD9511
TYPICAL MODES OF OPERATION
CLOCK DISTRIBUTION ONLY
PLL WITH EXTERNAL VCXO/VCO FOLLOWED BY
CLOCK DISTRIBUTION
This is the most common operational mode for the AD9511.
An external oscillator (shown as VCO/VCXO) is phase locked
to a reference input frequency applied to REFIN. The loop filter
is usually a passive design. A VCO or a VCXO can be used. The
CLK2 input is connected internally to the feedback divider, N.
The CLK2 input provides the feedback path for the PLL. If the
VCO/VCXO frequency exceeds maximum frequency of the
output(s) being used, an appropriate divide ratio must be set in
the corresponding divider(s) in the Distribution Section. Some
power can be saved by shutting off unused functions, as well as
by powering down any unused clock channels (see the Register
Map and Description section).
It is possible to use only the distribution section whenever the
PLL section is not needed. Some power can be saved by
shutting the PLL block off, as well as by powering down any
unused clock channels (see the Register Map Description
section).
In distribution mode, both the CLK1 and CLK2 inputs are
available for distribution to outputs via a low jitter multiplexer
(mux).
VREF
AD9511
REFIN
R
PFD
N
FUNCTION
PLL
REF
CLOCK
INPUT 1
REFIN
R
PFD
N
FUNCTION
CHARGE
PUMP
STATUS
CLK1
CLK2
DIVIDE
STATUS
CLK1
LVPECL
CLK2
VCXO,
VCO
DIVIDE
LVPECL
LVPECL
DIVIDE
DIVIDE
LVPECL
LVDS/CMOS
SERIAL
PORT
DIVIDE
LVDS/CMOS
DIVIDE
DIVIDE
LVDS/CMOS
ΔT
CLOCK
OUTPUTS
DIVIDE
Figure 31. Clock Distribution Mode
LVDS/CMOS
DIVIDE
ΔT
CLOCK
OUTPUTS
DIVIDE
LVPECL
SERIAL
PORT
CLOCK
INPUT 2
LVPECL
LOOP
FILTER
05286-010
REFERENCE
INPUT
AD9511
CHARGE
PUMP
Figure 30. PLL and Clock Distribution Mode
Rev. A | Page 26 of 60
05286-011
VREF
PLL
REF
AD9511
PLL WITH EXTERNAL VCO AND BAND-PASS
FILTER FOLLOWED BY CLOCK DISTRIBUTION
An external band-pass filter may be used to try to improve the
phase noise and spurious characteristics of the PLL output. This
option is most appropriate to optimize cost by choosing a less
expensive VCO combined with a moderately priced filter. Note
that the BPF is shown outside of the VCO-to-N divider path,
with the BP filter outputs routed to CLK1. Some power can be
saved by shutting off unused functions, as well as by powering
down any unused clock channels (see the Register Map and
Description section).
VREF
PLL
REF
R
PFD
N
FUNCTION
CHARGE
PUMP
LOOP
FILTER
STATUS
CLK1
CLK2
VCO
LVPECL
BPF
DIVIDE
LVPECL
DIVIDE
LVPECL
DIVIDE
LVDS/CMOS
SERIAL
PORT
CLOCK
OUTPUTS
DIVIDE
LVDS/CMOS
DIVIDE
ΔT
05286-012
REFERENCE
INPUT
AD9511
REFIN
Figure 32. AD9511 with VCO and BPF Filter
Rev. A | Page 27 of 60
AD9511
VS
RSET
GND
DISTRIBUTION
REF
REFIN
R DIVIDER
REFINB
N DIVIDER
FUNCTION
1.6GHz
AD9511
PHASE
FREQUENCY
DETECTOR
SYNCB,
RESETB
PDB
PLL
REF
CHARGE
PUMP
PLL
SETTINGS
CLK1
CP
STATUS
CLK2
CLK1B
1.6GHz
CLK2B
PROGRAMMABLE
DIVIDERS AND
PHASE ADJUST
LVPECL
OUT0
/1, /2, /3... /31, /32
OUT0B
LVPECL
OUT1
/1, /2, /3... /31, /32
OUT1B
1.2GHz
LVPECL
LVPECL
OUT2
/1, /2, /3... /31, /32
OUT2B
SCLK
SDIO
SDO
LVDS/CMOS
SERIAL
CONTROL
PORT
OUT3
/1, /2, /3... /31, /32
OUT3B
CSB
LVDS/CMOS
/1, /2, /3... /31, /32
ΔT
DELAY
ADJUST
Figure 33. Functional Block Diagram Showing Maximum Frequencies
Rev. A | Page 28 of 60
OUT4
OUT4B
800MHz
LVDS
250MHz
CMOS
05286-004
250MHz
CPRSET VCP
AD9511
FUNCTIONAL DESCRIPTION
Figure 33 shows a block diagram of the AD9511. The chip
combines a programmable PLL core with a configurable clock
distribution system. A complete PLL requires the addition of a
suitable external VCO (or VCXO) and loop filter. This PLL can
lock to a reference input signal and produce an output that is
related to the input frequency by the ratio defined by the
programmable R and N dividers. The PLL cleans up some jitter
from the external reference signal, depending on the loop
bandwidth and the phase noise performance of the VCO
(VCXO).
The output from the VCO (VCXO) can be applied to the clock
distribution section of the chip, where it can be divided by any
integer value from 1 to 32. The duty cycle and relative phase of
the outputs can be selected. There are three LVPECL outputs
(OUT0, OUT1, and OUT2) and two outputs that can be either
LVDS or CMOS level outputs (OUT3 or OUT4). OUT4 can
also make use of a variable delay block.
Alternatively, the clock distribution section can be driven
directly by an external clock signal, and the PLL can be powered
off. Whenever the clock distribution section is used alone, there
is no clock clean-up. The jitter of the input clock signal is
passed along directly to the distribution section and may
dominate at the clock outputs.
capacitor to a quiet ground. Figure 34 shows the equivalent
circuit of REFIN.
VS
10kΩ
12kΩ
REFIN
150Ω
REFINB
10kΩ
10kΩ
150Ω
05286-033
OVERALL
Figure 34. REFIN Equivalent Circuit
VCO/VCXO Clock Input—CLK2
The CLK2 differential input is used to connect an external VCO
or VCXO to the PLL. Only the CLK2 input port has a
connection to the PLL N divider. This input can receive up to
1.6 GHz. These inputs are internally self-biased and must be accoupled via capacitors.
Alternatively, CLK2 may be used as an input to the distribution
section. This is accomplished by setting Register 45h<0> = 0b.
The default condition is for CLK1 to feed the distribution section.
CLOCK INPUT
STAGE
VS
CLK
PLL SECTION
CLKB
The AD9511 consists of a PLL section and a distribution
section. If desired, the PLL section can be used separately from
the distribution section.
2.5kΩ
5kΩ
5kΩ
05286-016
The AD9511 has a complete PLL core on-chip, requiring only
an external loop filter and VCO/VCXO. This PLL is based on
the ADF4106, a PLL noted for its superb low phase noise
performance. The operation of the AD9511 PLL is nearly
identical to that of the ADF4106, offering an advantage to those
with experience with the ADF series of PLLs. Differences
include the addition of differential inputs at REFIN and CLK2,
and a different control register architecture. Also, the prescaler
has been changed to allow N as low as 1. The AD9511 PLL
implements the digital lock detect feature somewhat differently
than the ADF4106 does, offering improved functionality at
higher PFD rates. See the Register Map Description section.
2.5kΩ
Figure 35. CLK1, CLK2 Equivalent Input Circuit
PLL Reference Divider—R
The REFIN/REFINB inputs are routed to reference divider, R,
which is a 14-bit counter. R may be programmed to any value
from 1 to 16383 (a value of 0 results in a divide by 1) via its
control register (OBh<5:0>, OCh<7:0>). The output of the R
divider goes to one of the phase/frequency detector inputs. The
maximum allowable frequency into the phase, frequency
detector (PFD) must not be exceeded. This means that the
REFIN frequency divided by R must be less than the maximum
allowable PFD frequency. See Figure 34.
PLL Reference Input—REFIN
VCO/VCXO Feedback Divider—N (P, A, B)
The REFIN/REFINB pins can be driven by either a differential
or a single-ended signal. These pins are internally self-biased so
that they can be ac-coupled via capacitors. It is possible to dccouple to these inputs. If REFIN is driven single-ended, the
unused side (REFINB) should be decoupled via a suitable
The N divider is a combination of a prescaler, P, (3 bits) and two
counters, A (6 bits) and B (13 bits). Although the AD9511’s PLL
is similar to the ADF4106, the AD9511 has a redesigned
prescaler that allows lower values of N. The prescaler has both a
dual modulus (DM) and a fixed divide (FD) mode. The
AD9511 prescaler modes are shown in Table 14.
Rev. A | Page 29 of 60
AD9511
Table 14. PLL Prescaler Modes
Mode
(FD = Fixed Divide
DM = Dual Modulus)
FD
FD
P = 2 DM
P = 4 DM
P = 8 DM
P = 16 DM
P = 32 DM
FD
A and B Counters
Value in 0Ah<4:2>
000
001
010
011
100
101
110
111
Divide By
1
2
P/P + 1 = 2/3
P/P + 1 = 4/5
P/P + 1 = 8/9
P/P + 1 = 16/17
P/P + 1 = 32/33
3
When using the prescaler in FD mode, the A counter is not
used, and the B counter may need to be bypassed. The DM
prescaler modes set some upper limits on the frequency, which
can be applied to CLK2. See Table 15.
Note that the A counter is not used when the prescaler is in
FD mode.
Note also that the A/B counters have their own reset bit,
which is primarily intended for testing. The A and B counters
can also be reset using the R, A, and B counters’ shared reset bit
(09h<0>).
Determining Values for P, A, B, and R
When operating the AD9511 in a dual-modulus mode, the
input reference frequency, FREF, is related to the VCO output
frequency, FVCO.
Table 15. Frequency Limits of Each Prescaler Mode
Mode (DM = Dual Modulus)
P = 2 DM (2/3)
P = 4 DM (4/5)
P = 8 DM (8/9)
P = 16 DM
P = 32 DM
The AD9511 B counter has a bypass mode (B = 1), which is not
available on the ADF4106. The B counter bypass mode is valid
only when using the prescaler in FD mode. The B counter is
bypassed by writing 1 to the B counter bypass bit (0Ah<6> =
1b). The valid range of the B counter is 3 to 8191. The default
after a reset is 0, which is invalid.
CLK2
<600 MHz
<1000 MHz
<1600 MHz
<1600 MHz
<1600 MHz
FVCO = (FREF/R) × (PB + A) = FREF × N/R
When operating the prescaler in fixed divide mode, the A
counter is not used and the equation simplifies to
FVCO = (FREF/R) × (PB) = FREF × N/R
By using combinations of dual modulus and fixed divide
modes, the AD9511 can achieve values of N all the way down to
N = 1. Table 16 shows how a 10 MHz reference input may be
locked to any integer multiple of N. Note that the same value of
N may be derived in different ways, as illustrated by N = 12.
Table 16. P, A, B, R—Smallest Values for N
FREF
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
R
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
4
4
A
X
X
X
X
X
X
0
1
2
1
X
0
1
X
0
0
1
B
1
1
3
4
5
3
3
3
3
4
5
5
5
6
6
3
3
N
1
2
3
4
5
6
6
7
8
9
10
10
11
12
12
12
13
FVCO
10
20
30
40
50
60
60
70
80
90
100
100
110
120
120
120
130
Mode
FD
FD
FD
FD
FD
FD
DM
DM
DM
DM
FD
DM
DM
FD
DM
DM
DM
Rev. A | Page 30 of 60
Notes
P = 1, B = 1 (Bypassed)
P = 2, B = 1 (Bypassed)
P = 1, B = 3
P = 1, B = 4
P = 1, B = 5
P = 2, B = 3
P/P + 1 = 2/3, A = 0, B = 3
P/P + 1 = 2/3, A = 1, B = 3
P/P + 1 = 2/3, A = 2, B = 3
P/P + 1 = 2/3, A = 1, B = 4
P = 2, B = 5
P/P + 1 = 2/3, A = 0, B = 5
P/P + 1 = 2/3, A = 1, B = 5
P = 2, B = 6
P/P + 1 = 2/3, A = 0, B = 6
P/P + 1 = 4/5, A = 0, B = 3
P/P + 1 = 4/5, A = 1, B = 3
AD9511
Phase Frequency Detector (PFD) and Charge Pump
Antibacklash Pulse
The PFD takes inputs from the R counter and the N counter
(N = BP + A) and produces an output proportional to the phase
and frequency difference between them. Figure 36 is a
simplified schematic. The PFD includes a programmable delay
element that controls the width of the antibacklash pulse. This
pulse ensures that there is no dead zone in the PFD transfer
function and minimizes phase noise and reference spurs. Two
bits in Register 0Dh <1:0> control the width of the pulse.
The PLL features a programmable antibacklash pulse width that
is set by the value in Register 0Dh<1:0>. The default
antibacklash pulse width is 1.3 ns (0Dh<1:0> = 00b) and
normally should not need to be changed. The antibacklash
pulse eliminates the dead zone around the phase-locked
condition and thereby reduces the potential for certain spurs
that could be impressed on the VCO signal.
STATUS Pin
VP
The output multiplexer on the AD9511 allows access to various
signals and internal points on the chip at the STATUS pin.
Figure 37 shows a block diagram of the STATUS pin section.
The function of the STATUS pin is controlled by Register
08h<5:2>.
CHARGE
PUMP
UP
CLR1
PROGRAMMABLE
DELAY
PLL Digital Lock Detect
CP
U3
The STATUS pin can display two types of PLL lock detect:
digital (DLD) and analog (ALD). Whenever digital lock detect
is desired, the STATUS pin provides a CMOS level signal, which
can be active high or active low.
ANTIBACKLASH
PULSE WIDTH
HI
CLR2 DOWN
D2 Q2
U2
The digital lock detect has one of two time windows, as selected
by Register 0Dh<5>. The default (ODh<5> = 0b) requires the
signal edges on the inputs to the PFD to be coincident within
9.5 ns to set the DLD true, which then must separate by at least
15 ns to give DLD = false.
GND
05286-014
N DIVIDER
Figure 36. PFD Simplified Schematic and Timing (In Lock)
The other setting (ODh<5> = 1b) makes these coincidence
times 3.5 ns for DLD = true and 7 ns for DLD = false.
The DLD may be disabled by writing 1 to Register 0Dh<6>.
If the signal at REFIN goes away while DLD is true, the DLD
will not necessarily indicate loss-of-lock. See the Loss of
Reference section for more information.
OFF (LOW) (DEFAULT)
DIGITAL LOCK DETECT (ACTIVE HIGH)
N DIVIDER OUTPUT
DIGITAL LOCK DETECT (ACTIVE LOW)
R DIVIDER OUTPUT
ANALOG LOCK DETECT (N-CHANNEL OPEN DRAIN)
A COUNTER OUTPUT
PRESCALER OUTPUT (NCLK)
PFD UP PULSE
PFD DOWN PULSE
LOSS OF REFERENCE (ACTIVE HIGH)
TRI-STATE
ANALOG LOCK DETECT (P-CHANNEL OPEN DRAIN)
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE HIGH)
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE LOW)
LOSS OF REFERENCE (ACTIVE LOW)
SYNC
DETECT
SYNC DETECT ENABLE
58h <0>
PLL MUX CONTROL
08h <5:2>
Figure 37. STATUS Pin Circuit CLK1 Clock Input
Rev. A | Page 31 of 60
VS
STATUS
PIN
GND
05286-015
R DIVIDER
D1 Q1
U1
CONTROL FOR ANALOG
LOCK DETECT MODE
HI
AD9511
An analog lock detect (ALD) signal may be selected. When
ALD is selected, the signal at the STATUS pin is either an opendrain P-channel (08h<5:2> = 1100b) or an open-drain Nchannel (08h<5:2> = 0101b).
The analog lock detect signal is true (relative to the selected
mode) with brief false pulses. These false pulses get shorter as
the inputs to the PFD are nearer to coincidence and longer as
they are further from coincidence.
To extract a usable analog lock detect signal, an external RC
network is required to provide an analog filter with the
appropriate RC constant to allow for the discrimination of a
lock condition by an external voltage comparator. A 1 kΩ
resistor in parallel with a small capacitance usually fulfills this
requirement. However, some experimentation may be required
to get the desired operation.
The analog lock detect function may introduce some spurious
energy into the clock outputs. It is prudent to limit the use of
the ALD when the best possible jitter/phase noise performance
is required on the clock outputs.
Loss of Reference
The AD9511 PLL can warn of a loss-of-reference signal at
REFIN. The loss-of-reference monitor internally sets a flag
called LREF. Externally, this signal can be observed in several
ways on the STATUS pin, depending on the PLL MUX control
settings in Register 08h<5:2>. The LREF alone can be observed
as an active high signal by setting 08h<5:2> = <1010b> or as an
active low signal by setting 08h<5:2> = <1111b>.
The loss-of-reference circuit is clocked by the signal from the
VCO, which means that there must be a VCO signal present to
detect a loss of reference.
The digital lock detect (DLD) block of the AD9511 requires a
PLL reference signal to be present for the digital lock detect
output to be valid. It is possible to have a digital lock detect
indication (DLD = true) that remains true even after a loss-ofreference signal. For this reason, the digital lock detect signal
alone cannot be relied upon if the reference has been lost. There
is a way to combine the DLD and the LREF into a single signal
at the STATUS pin. Set 08h<5:2> = <1101b> to get a signal that
is the logical OR of the loss-of-lock (inverse of DLD) and the
loss-of-reference (LREF) active high. If an active low version of
this same signal is desired, set 08h<5:2> = <1110b>.
The reference monitor is enabled only after the DLD signal has
been high for the number of PFD cycles set by the value in
07h<6:5>. This delay is measured in PFD cycles. The delay
ranges from 3 PFD cycles (default) to 24 PFD cycles. When the
reference goes away, LREF goes true and the charge pump goes
into tri-state.
User intervention is required to take the part out of this state.
First, 07h<2> = 0b must be written in order to disable the lossof-reference circuit, taking the charge pump out of tri-state and
causing LREF to go false. A second write of 07h<2> = 1b is
required to re-enable the loss-of-reference circuit.
PLL LOOP LOCKS
DLD GOES TRUE
LREF IS FALSE
WRITE 07h<2> = 0
LREF SET FALSE
CHARGE PUMP COMES
OUT OF TRI-STATE
WRITE 07h<2> = 1
LOR ENABLED
n PFD CYCLES WITH
DLD TRUE
(n SET BY 07h<6:5>)
CHARGE PUMP
GOES INTO TRI-STATE.
LREF SET TRUE.
MISSING
REFERENCE
DETECTED
CHECK FOR PRESENCE
OF REFERENCE.
LREF STAYS FALSE IF
REFERENCE IS DETECTED.
05286-034
PLL Analog Lock Detect
Figure 38. Loss of Reference Sequence of Events
FUNCTION PIN
The FUNCTION pin (12) has three functions that are selected
by the value in Register 58h<6:5>. This pin is internally pulled
down by a 30 kΩ resistor. If this pin is left NC, the part is in
reset by default. To avoid this, connect this pin to VS with a
1 kΩ resistor.
RESETB: 58h<6:5> = 00b (Default)
In its default mode, the FUNCTION pin acts as RESETB, which
generates an asynchronous reset or hard reset when pulled low.
The resulting reset writes the default values into the serial
control port buffer registers as well as loading them into the
chip control registers. When the RESETB signal goes high
again, a synchronous sync is issued (see the SYNCB: 58h<6:5>
= 01b section) and the AD9511 resumes operation according to
the default values of the registers.
SYNCB: 58h<6:5> = 01b
The FUNCTION pin may be used to cause a synchronization or
alignment of phase among the various clock outputs. The
synchronization applies only to clock outputs that:
•
are not powered down
•
the divider is not masked (no sync = 0b)
•
are not bypassed (bypass = 0b)
SYNCB is level and rising edge sensitive. When SYNCB is low,
the set of affected outputs are held in a predetermined state,
defined by each divider’s start high bit. On a rising edge, the
dividers begin after a predefined number of fast clock cycles
(fast clock is the selected clock input, CLK1 or CLK2) as
determined by the values in the divider’s phase offset bits.
The SYNCB application of the FUNCTION pin is always active,
regardless of whether the pin is also assigned to perform reset
Rev. A | Page 32 of 60
AD9511
Each divider can be configured for divide ratio, phase, and duty
cycle. The phase and duty cycle values that can be selected
depend on the divide ratio that is chosen.
or power-down. When the SYNCB function is selected, the
FUNCTION pin does not act as either RESETB or PDB.
PDB: 58h<6:5> = 11b
The FUNCTION pin may also be programmed to work as an
asynchronous full power-down, PDB. Even in this full powerdown mode, there is still some residual VS current because
some on-chip references continue to operate. In PDB mode, the
FUNCTION pin is active low. The chip remains in a powerdown state until PDB is returned to logic high. The chip returns
to the settings programmed prior to the power-down.
See the Chip Power-Down or Sleep Mode—PDB section for
more details on what occurs during a PDB initiated powerdown.
Setting the Divide Ratio
The divide ratio is determined by the values written via the SCP
to the registers that control each individual output, OUT0 to
OUT4. These are the even numbered registers beginning at 4Ah
and going through 52h. Each of these registers is divided into
bits that control the number of clock cycles the divider output
stays high (high_cycles <3:0>) and the number of clock cycles
the divider output stays low (low_cycles <7:4>). Each value is 4
bits and has the range of 0 to 15.
The divide ratio is set by
DISTRIBUTION SECTION
Divide Ratio = (high_cycles + 1) + (low_cycles + 1)
As previously mentioned, the AD9511 is partitioned into two
operational sections: PLL and distribution. The PLL Section
was discussed previously. If desired, the distribution section can
be used separately from the PLL section.
CLK1 AND CLK2 CLOCK INPUTS
Either CLK1 or CLK2 may be selected as the input to the
distribution section. The CLK1 input can be connected to drive
the distribution section only. CLK1 is selected as the source for
the distribution section by setting Register 45h<0> = 1. This is
the power-up default state.
CLK1 and CLK2 work for inputs up to 1600 MHz. The jitter
performance is improved by a higher input slew rate. The input
level should be between approximately 150 mV p-p to no more
than 2 V p-p. Anything greater may result in turning on the
protection diodes on the input pins, which could degrade the
jitter performance.
See Figure 35 for the CLK1 and CLK2 equivalent input circuit.
These inputs are fully differential and self-biased. The signal
should be ac-coupled using capacitors. If a single-ended input
must be used, this can be accommodated by ac coupling to one
side of the differential input only. The other side of the input
should be bypassed to a quiet ac ground by a capacitor.
The unselected clock input (CLK1 or CLK2) should be powered
down to eliminate any possibility of unwanted crosstalk
between the selected clock input and the unselected clock input.
DIVIDERS
Each of the five clock outputs of the AD9511 has its own
divider. The divider can be bypassed to get an output at the
same frequency as the input (1×). When a divider is bypassed, it
is powered down to save power.
All integer divide ratios from 1 to 32 may be selected. A divide
ratio of 1 is selected by bypassing the divider.
Example 1:
Set the Divide Ratio = 2
high_cycles = 0
low_cycles = 0
Divide Ratio = (0 + 1) + (0 + 1) = 2
Example 2:
Set Divide Ratio = 8
high_cycles = 3
low_cycles = 3
Divide Ratio = (3 + 1) + (3 + 1) = 8
Note that a Divide Ratio of 8 may also be obtained by setting:
high_cycles = 2
low_cycles = 4
Divide Ratio = (2 + 1) + (4 + 1) = 8
Although the second set of settings produce the same divide
ratio, the resulting duty cycle is not the same.
Setting the Duty Cycle
The duty cycle and the divide ratio are related. Different divide
ratios have different duty cycle options. For example, if Divide
Ratio = 2, the only duty cycle possible is 50%. If the Divide
Ratio = 4, the duty cycle may be 25%, 50%, or 75%.
The duty cycle is set by
Duty Cycle = (high_cycles + 1)/[(high_cycles + 1) + (low_cycles + 1)]
See Table 17 for the values of the available duty cycles for each
divide ratio.
Rev. A | Page 33 of 60
AD9511
Table 17. Duty Cycle and Divide Ratio
Divide Ratio
2
3
3
4
4
4
5
5
5
5
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
8
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
11
11
11
11
11
Duty Cycle (%)
50
67
33
50
75
25
60
40
80
20
50
67
33
83
17
57
43
71
29
86
14
50
63
38
75
25
88
13
56
44
67
33
78
22
89
11
50
60
40
70
30
80
20
90
10
55
45
64
36
73
4Ah to 52h
LO<7:4>
HI<3:0>
0
0
1
1
0
2
1
2
0
3
2
1
3
0
4
2
3
1
4
0
5
3
2
4
1
5
0
6
3
4
2
5
1
6
0
7
4
3
5
2
6
1
7
0
8
4
5
3
6
2
0
1
0
1
2
0
2
1
3
0
2
3
1
4
0
3
2
4
1
5
0
3
4
2
5
1
6
0
4
3
5
2
6
1
7
0
4
5
3
6
2
7
1
8
0
5
4
6
3
7
Divide Ratio
11
11
11
11
11
12
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
13
13
14
14
14
14
14
14
14
14
14
14
14
14
14
15
15
15
15
15
15
15
15
15
Rev. A | Page 34 of 60
Duty Cycle (%)
27
82
18
91
9
50
58
42
67
33
75
25
83
17
92
8
54
46
62
38
69
31
77
23
85
15
92
8
50
57
43
64
36
71
29
79
21
86
14
93
7
53
47
60
40
67
33
73
27
80
4Ah to 52h
LO<7:4>
HI<3:0>
7
1
8
0
9
5
4
6
3
7
2
8
1
9
0
A
5
6
4
7
3
8
2
9
1
A
0
B
6
5
7
4
8
3
9
2
A
1
B
0
C
6
7
5
8
4
9
3
A
2
2
8
1
9
0
5
6
4
7
3
8
2
9
1
A
0
6
5
7
4
8
3
9
2
A
1
B
0
6
7
5
8
4
9
3
A
2
B
1
C
0
7
6
8
5
9
4
A
3
B
AD9511
Divide Ratio
15
15
15
15
15
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
Duty Cycle (%)
20
87
13
93
7
50
56
44
63
38
69
31
75
25
81
19
88
13
94
6
53
47
59
41
65
35
71
29
76
24
82
18
88
12
94
6
50
56
44
61
39
67
33
72
28
78
22
83
17
89
11
4Ah to 52h
LO<7:4>
HI<3:0>
B
1
C
0
D
7
6
8
5
9
4
A
3
B
2
C
1
D
0
E
7
8
6
9
5
A
4
B
3
C
2
D
1
E
0
F
8
7
9
6
A
5
B
4
C
3
D
2
E
1
F
2
C
1
D
0
7
8
6
9
5
A
4
B
3
C
2
D
1
E
0
8
7
9
6
A
5
B
4
C
3
D
2
E
1
F
0
8
9
7
A
6
B
5
C
4
D
3
E
2
F
1
Divide Ratio
19
19
19
19
19
19
19
19
19
19
19
19
19
19
20
20
20
20
20
20
20
20
20
20
20
20
20
21
21
21
21
21
21
21
21
21
21
21
21
22
22
22
22
22
22
22
22
22
22
22
23
Rev. A | Page 35 of 60
Duty Cycle (%)
53
47
58
42
63
37
68
32
74
26
79
21
84
16
50
55
45
60
40
65
35
70
30
75
25
80
20
52
48
57
43
62
38
67
33
71
29
76
24
50
55
45
59
41
64
36
68
32
73
27
52
4Ah to 52h
LO<7:4>
HI<3:0>
8
9
7
A
6
B
5
C
4
D
3
E
2
F
9
8
A
7
B
6
C
5
D
4
E
3
F
9
A
8
B
7
C
6
D
5
E
4
F
A
9
B
8
C
7
D
6
E
5
F
A
9
8
A
7
B
6
C
5
D
4
E
3
F
2
9
A
8
B
7
C
6
D
5
E
4
F
3
A
9
B
8
C
7
D
6
E
5
F
4
A
B
9
C
8
D
7
E
6
F
5
B
AD9511
Divide Ratio
23
23
23
23
23
23
23
23
23
24
24
24
24
24
24
24
24
24
25
25
25
25
25
25
25
25
26
26
Duty Cycle (%)
48
57
43
61
39
65
35
70
30
50
54
46
58
42
63
38
67
33
52
48
56
44
60
40
64
36
50
54
4Ah to 52h
LO<7:4>
HI<3:0>
B
9
C
8
D
7
E
6
F
B
A
C
9
D
8
E
7
F
B
C
A
D
9
E
8
F
C
B
A
C
9
D
8
E
7
F
6
B
C
A
D
9
E
8
F
7
C
B
D
A
E
9
F
8
C
D
Divide Ratio
26
26
26
26
26
27
27
27
27
27
27
28
28
28
28
28
29
29
29
29
30
30
30
31
31
32
Rev. A | Page 36 of 60
Duty Cycle (%)
46
58
42
62
38
52
48
56
44
59
41
50
54
46
57
43
52
48
55
45
50
53
47
52
48
50
4Ah to 52h
LO<7:4>
HI<3:0>
D
A
E
9
F
C
D
B
E
A
F
D
C
E
B
F
D
E
C
F
E
D
F
E
F
F
B
E
A
F
9
D
C
E
B
F
A
D
E
C
F
B
E
D
F
C
E
F
D
F
E
F
AD9511
In general, by combining the 4-bit phase offset and the Start
H/L bit, there are 32 possible phase offset states (see Table 18).
Divider Phase Offset
The phase of each output may be selected, depending on the
divide ratio chosen. This is selected by writing the appropriate
values to the registers, which set the phase and start high/low
bit for each output. These are the odd numbered registers from
4Bh to 53h. Each divider has a 4-bit phase offset <3:0> and a
start high or low bit <4>.
Table 18. Phase Offset—Start H/L Bit
Following a sync pulse, the phase offset word determines how
many fast clock (CLK1 or CLK2) cycles to wait before initiating
a clock output edge. The Start H/L bit determines if the divider
output starts low or high. By giving each divider a different
phase offset, output-to-output delays can be set in increments of
the fast clock period, tCLK.
Figure 39 shows three dividers, each set for DIV = 4, 50% duty
cycle. By incrementing the phase offset from 0 to 2, each output
is offset from the initial edge by a multiple of tCLK.
0
1
2
3
4
5
6
7
8
9
10
11 12
13
14
15
CLOCK INPUT
CLK
tCLK
DIVIDER OTUPUTS
DIV = 4, DUTY = 50%
START = 0,
PHASE = 0
START = 0,
PHASE = 1
START = 0,
PHASE = 2
05286-091
tCLK
2 × tCLK
Figure 39. Phase Offset—All Dividers Set for DIV = 4, Phase Set from 0 to 2
For example:
CLK1 = 491.52 MHz
tCLK1 = 1/491.52 = 2.0345 ns
For DIV = 4
Phase Offset 0 = 0 ns
Phase Offset
(Fast Clock
Rising Edges)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
4Bh to 53h
Phase Offset <3:0>
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Start H/L <4>
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
The resolution of the phase offset is set by the fast clock period
(tCLK) at CLK1 or CLK2. As a result, every divide ratio does not
have 32 unique phase offsets available. For any divide ratio, the
number of unique phase offsets is numerically equal to the
divide ratio (see Table 18):
Phase Offset 1 = 2.0345 ns
Phase Offset 2 = 4.069 ns
The three outputs may also be described as:
OUT1 = 0°
DIV = 4
OUT2 = 90°
Unique Phase Offsets Are Phase = 0, 1, 2, 3
OUT3 = 180°
DIV= 7
Setting the phase offset to Phase = 4 results in the same relative
phase as the first channel, Phase = 0° or 360°.
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6
Rev. A | Page 37 of 60
AD9511
DIV = 18
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,
11, 12, 13, 14, 15, 16, 17
Phase offsets may be related to degrees by calculating the phase
step for a particular divide ratio:
Phase Step = 360°/(Divide Ratio) = 360°/DIV
This path adds some jitter greater than that specified for the
nondelay outputs. This means that the delay function should be
used primarily for clocking digital chips, such as FPGA, ASIC,
DUC, and DDC, rather than for data converters. The jitter is
higher for long full scales (~10 ns). This is because the delay
block uses a ramp and trip points to create the variable delay. A
longer ramp means more noise may be introduced.
Calculating the Delay
Using some of the same examples,
The following values and equations are used to calculate the
delay of the delay block.
DIV = 4
Phase Step = 360°/4 = 90°
Value of Ramp Current Control Bits (Register 35h or Register 39h
<2:0>) = Iramp_bits
Unique Phase Offsets in Degrees Are Phase = 0°, 90°,
180°, 270°
IRAMP (μA) = 200 × (Iramp_bits + 1)
No. of Caps = No. of 0s + 1 in Ramp Control Capacitor
(Register 35h or Register 39h <5:3>), that is, 101 = 1 + 1 = 2; 110
= 2; 100 = 2 + 1 = 3; 001 = 2 + 1 = 3; 111 = 0 + 1 = 1)
DIV = 7
Phase Step = 360°/7 = 51.43°
Delay_Range (ns) = 200 × [(No. of Caps + 3)/(IRAMP)] × 1.3286
Unique Phase Offsets in Degrees Are Phase = 0°, 51.43°,
102.86°, 154.29°, 205.71°, 257.15°, 308.57°
⎛ No.of Caps − 1 ⎞
⎟×6
Offset (ns ) = 0.34 + (1600 − I RAMP )× 10 −4 + ⎜⎜
⎟
I RAMP
⎝
⎠
DELAY BLOCK
OUT4 (LVDS/CMOS) includes an analog delay element that
can be programmed (Register 34h to Register 36h) to give
variable time delays (ΔT) in the clock signal passing through
that output.
Delay_Full_Scale (ns) = Delay_Range + Offset
Fine_Adj = Value of Delay Fine Adjust (Register 36h or
Register 3Ah <5:1>), that is, 11111 = 31
CLOCK INPUT
Delay (ns) = Offset + Delay_Range × Fine_adj × (1/31)
OUT4 ONLY
OUTPUTS
CMOS
OUTPUT
DRIVER
FINE DELAY ADJUST
(32 STEPS)
FULL-SCALE: 1ns TO 10ns
Figure 40. Analog Delay (OUT4)
The amount of delay that can be used is determined by the
frequency of the clock being delayed. The amount of delay can
approach one-half cycle of the clock period. For example, for a
10 MHz clock, the delay can extend to the full 10 ns maximum
of which the delay element is capable. However, for a 100 MHz
clock (with 50% duty cycle), the maximum delay is less than
5 ns (or half of the period).
The AD9511 offers three different output level choices:
LVPECL, LVDS, and CMOS. OUT0 to OUT2 are LVPECL only.
OUT3 and OUT4 can be selected as either LVDS or CMOS.
Each output can be enabled or turned off as needed to save
power.
The simplified equivalent circuit of the LVPECL outputs is
shown in Figure 41.
3.3V
OUT
OUT4 allows a full-scale delay in the range 1 ns to 10 ns. The
full-scale delay is selected by choosing a combination of ramp
current and the number of capacitors by writing the appropriate
values into Register 35h. There are 32 fine delay settings for
each full scale, set by Register 36h.
OUTB
GND
05286-037
ΔT
LVDS
05286-092
MUX
÷N
∅SELECT
Figure 41. LVPECL Output Simplified Equivalent Circuit
Rev. A | Page 38 of 60
AD9511
Table 19. Register 0Ah: PLL Power-Down
3.5mA
<1>
0
0
1
1
OUT
OUTB
In synchronous power-down mode, the PLL power-down is
gated by the charge pump to prevent unwanted frequency
jumps. The device goes into power-down on the occurrence of
the next charge pump event after the registers are updated.
Figure 42. LVDS Output Simplified Equivalent Circuit
POWER-DOWN MODES
Chip Power-Down or Sleep Mode—PDB
The PDB chip power-down turns off most of the functions and
currents in the AD9511. When the PDB mode is enabled, a chip
power-down is activated by taking the FUNCTION pin to a
logic low level. The chip remains in this power-down state until
PDB is brought back to logic high. When woken up, the
AD9511 returns to the settings programmed into its registers
prior to the power-down, unless the registers are changed by
new programming while the PDB mode is active.
The PDB power-down mode shuts down the currents on the
chip, except the bias current necessary to maintain the LVPECL
outputs in a safe shutdown mode. This is needed to protect the
LVPECL output circuitry from damage that could be caused by
certain termination and load configurations when tri-stated.
Because this is not a complete power-down, it can be called
sleep mode.
When the AD9511 is in a PDB power-down or sleep mode, the
chip is in the following state:
•
The PLL is off (asynchronous power-down).
•
All clocks and sync circuits are off.
•
All dividers are off.
•
All LVDS/CMOS outputs are off.
•
All LVPECL outputs are in safe off mode.
•
The serial control port is active, and the chip responds to
commands.
If the AD9511 clock outputs must be synchronized to each
other, a SYNC (see the Single-Chip Synchronization section) is
required upon exiting power-down mode.
PLL Power-Down
Mode
Normal Operation
Asynchronous Power-Down
Normal Operation
Synchronous Power-Down
In asynchronous power-down mode, the device powers down as
soon as the registers are updated.
05286-038
3.5mA
<0>
0
1
0
1
Distribution Power-Down
The distribution section can be powered down by writing to
Register 58h<3> = 1. This turns off the bias to the distribution
section. If the LVPECL power-down mode is normal operation
<00>, it is possible for a low impedance load on that LVPECL
output to draw significant current during this power-down. If
the LVPECL power-down mode is set to <11>, the LVPECL
output is not protected from reverse bias, and can be damaged
under certain termination conditions.
When combined with the PLL power-down, this mode results in
the lowest possible power-down current for the AD9511.
Individual Clock Output Power-Down
Any of the five clock distribution outputs can be powered down
individually by writing to the appropriate registers via the SCP.
The register map details the individual power-down settings for
each output. The LVDS/CMOS outputs may be powered down,
regardless of their output load configuration.
The LVPECL outputs have multiple power-down modes (see
Register 3Dh, Register 3Eh, and Register 3Fh in Table 24).
These give some flexibility in dealing with various output
termination conditions. When the mode is set to <10b>, the
LVPECL output is protected from reverse bias to 2 VBE + 1 V. If
the mode is set to <11b>, the LVPECL output is not protected
from reverse bias and can be damaged under certain
termination conditions. This setting also affects the operation
when the distribution block is powered down with Register
58h<3> = 1b (see the Distribution Power-Down section).
Individual Circuit Block Power-Down
Many of the AD9511 circuit blocks (CLK1, CLK2, and REFIN,
and so on) can be powered down individually. This gives
flexibility in configuring the part for power savings whenever
certain chip functions are not needed.
The PLL section of the AD9511 can be selectively powered
down. There are three PLL power-down modes, set by the
values in Register 0Ah<1:0>, as shown in Table 19.
Rev. A | Page 39 of 60
AD9511
The AD9511 has several ways to force the chip into a reset
condition.
Power-On Reset—Start-Up Conditions when VS is
Applied
A power-on reset (POR) is issued when the VS power supply is
turned on. This initializes the chip to the power-on conditions
that are determined by the default register settings. These are
indicated in the default value column of Table 23.
Asynchronous Reset via the FUNCTION Pin
As mentioned in the FUNCTION Pin section, a hard reset,
RESETB: 58h<6:5> = 00b (Default), restores the chip to the
default settings.
Soft Reset via the Serial Port
The serial control port allows a soft reset by writing to
Register 00h<5> = 1b. When this bit is set, the chip executes a
soft reset. This restores the default values to the internal
registers, except for Register 00h itself.
This bit is not self-clearing. The bit must be written to
00h<5> = 0b for the operation of the part to continue.
SINGLE-CHIP SYNCHRONIZATION
SYNCB—Hardware SYNC
The AD9511 clocks can be synchronized to each other at any
time. The outputs of the clocks are forced into a known state
with respect to each other and then allowed to continue
clocking from that state in synchronicity. Before a
synchronization is done, the FUNCTION Pin must be set as the
SYNCB: 58h<6:5> = 01b input (58h<6:5> = 01b).
Synchronization is done by forcing the FUNCTION pin low,
creating a SYNCB signal and then releasing it.
See the SYNCB: 58h<6:5> = 01b section for a more detailed
description of what happens when the SYNCB: 58h<6:5> = 01b
signal is issued.
Synchronization of two or more AD9511s requires a fast clock
and a slow clock. The fast clock can be up to 1 GHz and may be
the clock driving the master AD9511 CLK1 input or one of the
outputs of the master. The fast clock acts as the input to the
distribution section of the slave AD9511 and is connected to its
CLK1 input. The PLL may be used on the master, but the slave
PLL is not used.
The slow clock is the clock that is synchronized across the two
chips. This clock must be no faster than one-fourth of the fast
clock, and no greater than 250 MHz. The slow clock is taken
from one of the outputs of the master AD9511 and acts as the
REFIN (or CLK2) input to the slave AD9511. One of the
outputs of the slave must provide this same frequency back to
the CLK2 (or REFIN) input of the slave.
Multichip synchronization is enabled by writing to Register
58h<0> = 1b on the slave AD9511. When this bit is set, the
STATUS pin becomes the output for the SYNC signal. A low
signal indicates an in-sync condition, and a high indicates an
out-of-sync condition.
Register 58h<1> selects the number of fast clock cycles that are
the maximum separation of the slow clock edges that are
considered synchronized. When 58h<1> = 0b (default), the
slow clock edges must be coincident within 1 to 1.5 high speed
clock cycles. If the coincidence of the slow clock edges is closer
than this amount, the SYNC flag stays low. If the coincidence of
the slow clock edges is greater than this amount, the SYNC flag
is set high. When Register 58h<1> = 1b, the amount of
coincidence required is 0.5 fast clock cycles to 1 fast clock
cycles.
Whenever the SYNC flag is set (high), indicating an out-of-sync
condition, a SYNCB signal applied simultaneously at the
FUNCTION pins of both AD9511s brings the slow clocks into
synchronization.
AD9511
MASTER
FAST CLOCK
<1GHz
OUTN
SLOW CLOCK
<250MHz
OUTM
Soft SYNC—Register 58h<2>
A soft SYNC may be issued by means of a bit in the Register
58h<2>. This soft SYNC works the same as the SYNCB, except
that the polarity is reversed. A 1 written to this bit forces the
clock outputs into a known state with respect to each other.
When a 0 is subsequently written to this bit, the clock outputs
continue clocking from that state in synchronicity.
FUNCTION
(SYNCB)
FSYNC
SYNCB
MULTICHIP SYNCHRONIZATION
The AD9511 provides a means of synchronizing two or more
AD9511s. This is not an active synchronization; it requires user
monitoring and action. The arrangement of two AD9511s to be
synchronized is shown in Figure 43.
CLK2
REFIN
AD9511
SLAVE
FAST CLOCK
CLK1 <1GHz
SLOW
CLOCK
<250MHz
SYNC
DETECT
FUNCTION
(SYNCB)
Figure 43. Multichip Synchronization
Rev. A | Page 40 of 60
FSYNC
OUTY
STATUS
(SYNC)
05286-093
RESET MODES
AD9511
SERIAL CONTROL PORT
The AD9511 serial control port is a flexible, synchronous, serial
communications port that allows an easy interface with many
industry-standard microcontrollers and microprocessors. The
AD9511 serial control port is compatible with most
synchronous transfer formats, including both the Motorola SPI®
and Intel® SSR protocols. The serial control port allows
read/write access to all registers that configure the AD9511.
Single or multiple byte transfers are supported, as well as MSB
first or LSB first transfer formats. The AD9511 serial control
port can be configured for a single bidirectional I/O pin (SDIO
only) or for two unidirectional I/O pins (SDIO/SDO).
not brought high at the end of each write or read cycle (on a
byte boundary), the last byte is not loaded into the register
buffer.
SCLK (serial clock) is the serial shift clock. This pin is an input.
SCLK is used to synchronize serial control port reads and
writes. Write data bits are registered on the rising edge of this
clock, and read data bits are registered on the falling edge. This
pin is internally pulled down by a 30 kΩ resistor to ground.
CSB stall high is supported in modes where three or fewer bytes
of data (plus instruction data) are transferred (W1:W0 must be
set to 00, 01, or 10, see Table 20). In these modes, CSB can
temporarily return high on any byte boundary, allowing time
for the system controller to process the next byte. CSB can go
high on byte boundaries only and can go high during either
part (instruction or data) of the transfer. During this period, the
serial control port state machine enters a wait state until all data
has been sent. If the system controller decides to abort the
transfer before all of the data is sent, the state machine must be
reset by either completing the remaining transfer or by
returning the CSB low for at least one complete SCLK cycle (but
less than eight SCLK cycles). Raising the CSB on a nonbyte
boundary terminates the serial transfer and flushes the buffer.
SDIO (serial data input/output) is a dual-purpose pin and acts
as either an input only or as both an input/output. The AD9511
defaults to two unidirectional pins for I/O, with SDIO used as
an input and SDO as an output. Alternatively, SDIO can be used
as a bidirectional I/O pin by writing to the SDO enable register
at 00h<7> = 1b.
In the streaming mode (W1:W0 = 11b), any number of data
bytes can be transferred in a continuous stream. The register
address is automatically incremented or decremented (see the
MSB/LSB First Transfers section). CSB must be raised at the
end of the last byte to be transferred, thereby ending the
stream mode.
SDO (serial data out) is used only in the unidirectional I/O
mode (00h<7> = 0b, default) as a separate output pin for
reading back data. The AD9511 defaults to this I/O mode.
Bidirectional I/O mode (using SDIO as both input and output)
may be enabled by writing to the SDO enable register at
00h<7> = 1b.
Communication Cycle—Instruction Plus Data
SERIAL CONTROL PORT PIN DESCRIPTIONS
CSB (chip select bar) is an active low control that gates the read
and write cycles. When CSB is high, SDO and SDIO are in a
high impedance state. This pin is internally pulled down by a
30 kΩ resistor to ground. It should not be left NC or tied low.
See the Framing a Communication Cycle with CSB section on
the use of the CSB in a communication cycle.
SDIO (PIN 15)
SDO (PIN 16)
CSB (PIN 17)
AD9511
SERIAL
CONTROL
PORT
05286-094
SCLK (PIN 14)
Figure 44. Serial Control Port
GENERAL OPERATION OF SERIAL CONTROL PORT
Framing a Communication Cycle with CSB
Each communication cycle (a write or a read operation) is gated
by the CSB line. CSB must be brought low to initiate a
communication cycle. CSB must be brought high at the
completion of a communication cycle (see Figure 52). If CSB is
There are two parts to a communication cycle with the AD9511.
The first writes a 16-bit instruction word into the AD9511,
coincident with the first 16 SCLK rising edges. The instruction
word provides the AD9511 serial control port with information
regarding the data transfer, which is the second part of the
communication cycle. The instruction word defines whether
the upcoming data transfer is a read or a write, the number of
bytes in the data transferred, and the starting register address
for the first byte of the data transfer.
Write
If the instruction word is for a write operation (I15 = 0b), the
second part is the transfer of data into the serial control port
buffer of the AD9511. The length of the transfer (1, 2, 3 bytes or
streaming mode) is indicated by two bits (W1:W0) in the
instruction byte. CSB can be raised after each sequence of eight
bits to stall the bus (except after the last byte, where it ends the
cycle). When the bus is stalled, the serial transfer resumes when
CSB is lowered. Stalling on nonbyte boundaries resets the serial
control port.
Since data is written into a serial control port buffer area, not
directly into the AD9511’s actual control registers, an additional
operation is needed to transfer the serial control port buffer
contents to the actual control registers of the AD9511, thereby
causing them to take effect. This update command consists of
Rev. A | Page 41 of 60
AD9511
writing to Register 5Ah<0> = 1b. This update bit is self-clearing
(it is not required to write 0 to it to clear it). Since any number
of bytes of data can be changed before issuing an update
command, the update simultaneously enables all register
changes since any previous update.
Phase offsets or divider synchronization is not effective until a
SYNC is issued (see the Single-Chip Synchronization section).
Read
If the instruction word is for a read operation (I15 = 1b), the
next N × 8 SCLK cycles clock out the data from the address
specified in the instruction word, where N is 1 to 4 as
determined by W1:W0. The readback data is valid on the falling
edge of SCLK.
The default mode of the AD9511 serial control port is
unidirectional mode; therefore, the requested data appears on
the SDO pin. It is possible to set the AD9511 to bidirectional
mode by writing the SDO enable register at 00h<7> = 1b. In
bidirectional mode, the readback data appears on the SDIO pin.
SDO
CSB
SERIAL
CONTROL
PORT
UPDATE
REGISTERS
5Ah <0>
AD9511
CORE
05286-095
SDIO
CONTROL REGISTERS
SCLK
REGISTER BUFFERS
A readback request reads the data that is in the serial control
port buffer area, not the active data in the AD9511’s actual
control registers.
Figure 45. Relationship Between Serial Control Port Register Buffers and
Control Registers of the AD9511
The AD9511 uses Address 00h to Address 5Ah. Although the
AD9511 serial control port allows both 8-bit and 16-bit
instructions, the 8-bit instruction mode provides access to five
address bits (A4 to A0) only, which restricts its use to the
address space 00h to 01F. The AD9511 defaults to 16-bit
instruction mode on power-up. The 8-bit instruction mode
(although defined for this serial control port) is not useful for
the AD9511; therefore, it is not discussed further in this data
sheet.
THE INSTRUCTION WORD (16 BITS)
The MSB of the instruction word is R/W, which indicates
whether the instruction is a read or a write. The next two bits,
W1:W0, indicate the length of the transfer in bytes. The final 13
bits are the addresses (A12:A0) at which to begin the read or
write operation.
For a write, the instruction word is followed by the number of
bytes of data indicated by Bits W1:W0, which is interpreted
according to Table 20.
Table 20. Byte Transfer Count
W1
W0
Bytes to Transfer
0
0
1
1
0
1
0
1
1
2
3
4
A12:A0: These 13 bits select the address within the register map
that is written to or read from during the data transfer portion
of the communications cycle. The AD9511 does not use all of
the 13-bit address space. Only Bits A6:A0 are needed to cover
the range of the 5Ah registers used by the AD9511. Bits A12:A7
must always be 0b. For multibyte transfers, this address is the
starting byte address. In MSB first mode, subsequent bytes
increment the address.
MSB/LSB FIRST TRANSFERS
The AD9511 instruction word and byte data may be MSB first
or LSB first. The default for the AD9511 is MSB first. The LSB
first mode may be set by writing 1b to Register 00h<6>. This
takes effect immediately (since it only affects the operation of
the serial control port) and does not require that an update be
executed. Immediately after the LSB first bit is set, all serial
control port operations are changed to LSB first order.
When MSB first mode is active, the instruction and data bytes
must be written from MSB to LSB. Multibyte data transfers in
MSB first format start with an instruction byte that includes the
register address of the most significant data byte. Subsequent
data bytes must follow in order from high address to low
address. In MSB first mode, the serial control port internal
address generator decrements for each data byte of the
multibyte transfer cycle.
When LSB_First = 1b (LSB first), the instruction and data bytes
must be written from LSB to MSB. Multibyte data transfers in
LSB first format start with an instruction byte that includes the
register address of the least significant data byte followed by
multiple data bytes. The serial control port internal byte address
generator increments for each byte of the multibyte transfer
cycle.
The AD9511 serial control port register address decrements
from the register address just written toward 0000h for
multibyte I/O operations if the MSB first mode is active
(default). If the LSB first mode is active, the serial control port
register address increments from the address just written
toward 1FFFh for multibyte I/O operations.
Unused addresses are not skipped during multibyte I/O
operations; therefore, it is important to avoid multibyte I/O
operations that would include these addresses.
Rev. A | Page 42 of 60
AD9511
Table 21. Serial Control Port, 16-Bit Instruction Word, MSB First
MSB
I15
I14
I13
I12
I11
I10
I9
I8
I7
I6
I5
I4
I3
I2
I1
LSB
I0
R/W
W1
W0
A12 = 0
A11 = 0
A10 = 0
A9 = 0
A8 = 0
A7 = 0
A6
A5
A4
A3
A2
A1
A0
CSB
SCLK DON'T CARE
R/W W1 W0 A12 A11 A10 A9
A8
A7
A6 A5
A4 A3 A2
A1 A0
16-BIT INSTRUCTION HEADER
D7 D6 D5
D4 D3
D2 D1
D0
D7
REGISTER (N) DATA
D6 D5
D4 D3 D2
D1 D0
DON'T CARE
REGISTER (N – 1) DATA
05286-019
SDIO DON'T CARE
DON'T CARE
Figure 46. Serial Control Port Write—MSB First, 16-Bit Instruction, 2 Bytes of Data
CSB
SCLK
DON'T CARE
DON'T CARE
R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
SDO DON'T CARE
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
16-BIT INSTRUCTION HEADER
REGISTER (N) DATA
REGISTER (N – 1) DATA
REGISTER (N – 2) DATA
REGISTER (N – 3) DATA
DON'T
CARE
05286-020
SDIO
Figure 47. Serial Control Port Read—MSB First, 16-Bit Instruction, 4 Bytes od Data
tDS
tHI
tS
tDH
DON'T CARE
SDIO
DON'T CARE
DON'T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
D4
D3
D2
D1
D0
DON'T CARE
05286-021
SCLK
tH
tCLK
tLO
CSB
Figure 48. Serial Control Port Write—MSB First, 16-Bit Instruction, Timing Measurements
CSB
SCLK
DATA BIT N
05286-022
tDV
SDIO
SDO
DATA BIT N– 1
Figure 49. Timing Diagram for Serial Control Port Register Read
CSB
SCLK DON'T CARE
A0 A1 A2 A3
A4
A5 A6 A7
A8
A9 A10 A11 A12 W0 W1 R/W D0 D1 D2 D3 D4
16-BIT INSTRUCTION HEADER
D5 D6
REGISTER (N) DATA
D7
D0
D1 D2
D6
REGISTER (N + 1) DATA
Figure 50. Serial Control Port Write—LSB First, 16-Bit Instruction, 2 Bytes Data
Rev. A | Page 43 of 60
D3 D4 D5
D7
DON'T CARE
05286-023
SDIO DON'T CARE
DON'T CARE
AD9511
tS
tH
CSB
tCLK
tHI
tLO
tDS
SCLK
SDIO
BI N
05286-040
tDH
BI N + 1
Figure 51. Serial Control Port Timing—Write
Table 22. Serial Control Port Timing
Parameter
tDS
tDH
tCLK
tS
tH
tHI
tLO
Description
Setup time between data and rising edge of SCLK
Hold time between data and rising edge of SCLK
Period of the clock
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
CSB TOGGLE INDICATES
CYCLE COMPLETE
tPWH
CSB
16 INSTRUCTION BITS + 8 DATA BITS
16 INSTRUCTION BITS + 8 DATA BITS
SCLK
COMMUNICATION CYCLE 1
COMMUNICATION CYCLE 2
TIMING DIAGRAM FOR TWO SUCCESSIVE COMMUNICATION CYCLES. NOTE THAT CSB MUST
BE TOGGLED HIGH AND THEN LOW AT THE COMPLETION OF A COMMUNICATION CYCLE.
Figure 52. Use of CSB to Define Communications Cycles
Rev. A | Page 44 of 60
05286-067
SDIO
AD9511
REGISTER MAP AND DESCRIPTION
SUMMARY TABLE
Table 23. AD9511 Register Map
Addr
(Hex)
00
Parameter
Serial
Control Port
Configuration
Bit 7 (MSB)
SDO Inactive
(Bidirectional
Mode)
Bit 6
LSB
First
Bit 5
Soft
Reset
Bit 4
Long
Instruction
Bit 3
Bit 2
Bit 1
Not Used
Bit 0
(LSB)
Def.
Value
(Hex)
10
Not Used
01,
02,
03
PLL
04
A Counter
05
B Counter
06
B Counter
07
PLL 1
08
PLL 2
09
PLL 3
0A
PLL 4
0B
0C
0D
R Divider
R Divider
PLL 5
OE33
Not Used
6-Bit A Counter <5:0>
Not Used
00
13-Bit B Counter Bits 12:8 (MSB) <4:0>
00
13-Bit B Counter Bits 7:0 (LSB) <7:0>
00
Not Used
Not Used
Not
LOR Lock_Del
LOR
Used
<6:5>
Enable
CP Mode <1:0>
Not
PFD
PLL Mux Select <5:2>
Used
Polarity
Signal on STATUS pin
CP Current <6:4>
Not
Not
Reset R
Reset N Reset All
Used
Used Counter Counter Counters
Prescaler P <4:2>
Power-Down <1:0>
Not
B
Not
Used
Bypass
Used
Not Used
14-Bit R Divider Bits 13:8 (MSB) <5:0>
14-Bit R Divider Bits 13:8 (MSB) <7:0>
Not Used
Not
Digital
Digital
Antibacklash
Used
Lock
Lock
Pulse Width <1:0>
Det
Det
Enable Window
Not Used
34
Delay Bypass 4
Not Used
35
Delay
Full-Scale 4
Not Used
36
Delay Fine
Adjust 4
Not Used
Ramp Capacitor <5:3>
5-Bit Fine Delay <5:1>
Not Used
Rev. A | Page 45 of 60
Bypass
Ramp Current <2:0>
Not
Used
PLL Starts
in PowerDown
N Divider
(A)
N Divider
(B)
N Divider
(B)
00
00
00
01
00
00
00
FINE DELAY
ADJUST
37,
38,
39,
3A,
3B,
3C
Notes
01
00
00
N Divider
(P)
R Divider
R Divider
Fine
Delays
Bypassed
Bypass
Delay
Max.
Delay
Full-Scale
Min. Delay
Value
AD9511
Addr
(Hex)
3D
Parameter
OUTPUTS
LVPECL OUT0
Bit 7 (MSB)
Bit 6
Bit 5
3E
LVPECL OUT1
Not Used
3F
LVPECL OUT2
Not Used
40
LVDS_CMOS
OUT 3
Not Used
41
LVDS_CMOS
OUT 4
Not Used
Not Used
45
Not Used
CLKs in
PD
4A
4B
DIVIDERS
Divider 0
Divider 0
Bypass
4C
4D
Divider 1
Divider 1
Bypass
4E
4F
Divider 2
Divider 2
Bypass
50
51
Divider 3
Divider 3
Bypass
52
53
Divider 4
Divider 4
Bypass
Low Cycles <7:4>
Force
No
Sync
Low Cycles <7:4>
Force
No
Sync
Low Cycles <7:4>
Force
No
Sync
Low Cycles <7:4>
Force
No
Sync
Low Cycles <7:4>
Force
No
Sync
Bit 1
Power-Down <1:0>
Output Level
<3:2>
Power-Down <1:0>
Output Level
<3:2>
Power-Down <1:0>
Output Level
<3:2>
Logic
Output Level
Output
Select
<2:1>
Power
REFIN PD
CLK
to
PLL
PD
Output Level
<2:1>
CLK2
PD
CLK1
PD
Output
Power
Select
CLK IN
Notes
08
ON
08
ON
08
ON
02
LVDS, ON
02
LVDS, ON
01
Input
Receivers
All Clocks
ON, Select
CLK1
Start H/L
High Cycles <3:0>
Phase Offset <3:0>
00
00
Divide by 2
Phase = 0
Start H/L
High Cycles <3:0>
Phase Offset <3:0>
11
00
Divide by 4
Phase = 0
Start H/L
High Cycles <3:0>
Phase Offset <3:0>
33
00
Divide by 8
Phase = 0
Start H/L
High Cycles <3:0>
Phase Offset <3:0>
00
00
Divide by 2
Phase = 0
Start H/L
High Cycles <3:0>
Phase Offset <3:0>
11
00
Divide by 4
Phase = 0
Sync
Enable
00
FUNCTION
Pin =
RESETB
Update
Registers
00
SelfClearing
Bit
Not Used
54,
55,
56,
57
59
5A
Bit 2
Def.
Value
(Hex)
Not Used
46,
47,
48, 49
58
Bit 3
CMOS
Inverted
Driver On
CMOS
Logic
Inverted
Select
Driver On
Not Used
42,
43,
44
CLK1 AND
CLK2
Clocks Select,
Power-Down
(PD) Options
Bit 4
Bit 0
(LSB)
FUNCTION
FUNCTION
Pin and Sync
Update
Registers
Not
Used
Set FUNCTION Pin
PD Sync
PD All
Ref
Not Used
Not Used
END
Rev. A | Page 46 of 60
Sync
Reg
Sync
Select
AD9511
REGISTER MAP DESCRIPTION
Table 24 lists the AD9511 control registers by hexadecimal address. A specific bit or range of bits within a register is indicated by angle
brackets. For example, <3> refers to Bit 3, while <5:2> refers to the range of bits from Bit 5 through Bit 2. Table 24 describes the
functionality of the control registers on a bit-by-bit basis. For a more concise (but less descriptive) table, see Table 23.
Table 24. AD9511 Register Descriptions
Reg.
Addr.
(Hex)
00
Bit(s) Name
Serial Control Port
Configuration
<3:0>
Description
Any changes to this register takes effect immediately. Register 5Ah<0> Update Registers does not
have to be written.
Not Used.
00
<4>
Long Instruction
00
<5>
Soft Reset
00
<6>
LSB First
00
<7>
SDO Inactive
(Bidirectional
Mode)
Not Used
When this bit is set (1), the instruction phase is 16 bits. When clear (0), the instruction phase is 8 bits.
The default, and only, mode for this part is long instruction (Default = 1b).
When this bit is set (1), the chip executes a soft reset, restoring default values to the internal
registers, except for this register, 00h. This bit is not self-clearing. A clear (0) has to be written
to it to clear it.
When this bit is set (1), the input and output data is oriented as LSB first. Additionally, register
addressing increments. If this bit is clear (0), data is oriented as MSB first and register addressing
decrements. (Default = 0b, MSB first).
When set (1), the SDO pin is tri-state and all read data goes to the SDIO pin. When clear (0), the
SDO is active (unidirectional mode). (Default = 0b).
01
02
03
<7:0>
<7:0>
<7:0>
Not Used.
Not Used.
Not Used.
PLL Settings
04
04
05
05
06
07
07
07
07
<5:0>
<7:6>
<4:0>
<7:5>
<7:0>
<1:0>
<2>
<4:3>
<6:5>
A Counter
07
08
<7>
<1:0> Charge Pump
Mode
B Counter MSBs
B Counter LSBs
LOR Enable
LOR Initial Lock
Detect Delay
6-Bit A Counter <5:0>.
Not Used.
13-Bit B Counter (MSB) <12:8>.
Not Used.
13-Bit B Counter (LSB) <7:0>.
Not Used.
1 = Enables the Loss-of-Reference (LOR) Function; (Default = 0b).
Not Used.
LOR Initial Lock Detect Delay. Once a lock detect is indicated, this is the number of phase frequency
detector (PFD) cycles that occur prior to turning on the LOR monitor.
<6>
<5>
LOR Initial Lock Detect Delay
0
0
3 PFD Cycles (Default)
0
1
6 PFD Cycles
1
0
12 PFD Cycles
1
1
24 PFD Cycles
Not Used
<1>
0
0
1
1
<0>
0
1
0
1
Rev. A | Page 47 of 60
Charge Pump Mode
Tri-Stated (Default)
Pump-Up
Pump-Down
Normal Operation
AD9511
Reg.
Addr.
(Hex)
08
Bit(s) Name
<5:2> PLL Mux Control
Description
<5>
0
0
0
0
0
0
0
0
1
1
1
1
1
1
<4>
0
0
0
0
1
1
1
1
0
0
0
0
1
1
<3>
0
0
1
1
0
0
1
1
0
0
1
1
0
0
<2>
0
1
0
1
0
1
0
1
0
1
0
1
0
1
MUXOUT—Signal on STATUS Pin
Off (Signal Goes Low) (Default)
Digital Lock Detect (Active High)
N Divider Output
Digital Lock Detect (Active Low)
R Divider Output
Analog Lock Detect (N Channel, Open-Drain)
A Counter Output
Prescaler Output (NCLK)
PFD Up Pulse
PFD Down Pulse
Loss-of-Reference (Active High)
Tri-State
Analog Lock Detect (P Channel, Open-Drain)
Loss-of-Reference or Loss-of-Lock (Inverse of DLD)
(Active High)
1
1
1
0
Loss-of-Reference or Loss-of-Lock (Inverse of DLD)
(Active Low)
1
1
1
1
Loss-of-Reference (Active Low)
MUXOUT is the PLL portion of the STATUS output MUX.
0 = Negative (Default), 1 = Positive.
08
<6>
Phase-Frequency
Detector (PFD)
Polarity
08
09
09
09
09
09
<7>
<0>
<1>
<2>
<3>
<6:4>
Not Used.
Reset All Counters 0 = Normal (Default), 1 = Reset R, A, and B Counters.
N-Counter Reset 0 = Normal (Default), 1 = Reset A and B Counters.
R-Counter Reset 0 = Normal (Default), 1 = Reset R Counter.
Not Used.
Charge Pump (CP)
Current Setting
<6>
<5>
<4>
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Default = 000b.
These currents assume: CPRSET = 5.1 kΩ.
Actual current can be calculated by: CP_lsb = 3.06/CPRSET.
Not Used.
09
<7>
Rev. A | Page 48 of 60
ICP (mA)
0.60
1.2
1.8
2.4
3.0
3.6
4.2
4.8
AD9511
Reg.
Addr.
(Hex)
0A
0A
Bit(s) Name
<1:0> PLL Power-Down
<0>
0
1
0
1
Mode
Normal Operation
Asynchronous Power-Down
Normal Operation
Synchronous Power-Down
<4:2> Prescaler Value
(P/P+1)
0A
0A
<5>
<6>
0A
0B
<7>
<5:0>
0C
<7:0>
0D
<1:0>
0D
0D
<4:2>
<5>
0D
<6>
0D
<7>
0E-33
Description
01 = Asynchronous Power-Down (Default).
<1>
0
0
1
1
<4>
<3>
<2> Mode Prescaler Mode
0
0
0
FD
Divide by 1
0
0
1
FD
Divide by 2
0
1
0
DM
2/3
0
1
1
DM
4/5
1
0
0
DM
8/9
1
0
1
DM
16/17
1
1
0
DM
32/33
1
1
1
FD
Divide by 3
DM = Dual Modulus, FD = Fixed Divide.
Not Used.
B Counter Bypass Only valid when operating the prescaler in fixed divide (FD) mode. When this bit is set, the
B counter is divided by 1. This allows the prescaler setting to determine the divide for the
N divider.
Not Used.
14-Bit Reference R Divider (MSB) <13:8>.
Counter, MSBs
14-Bit Reference R Divider (MSB) <7:0>.
Counter, R LSBs
Antibacklash
Pulse-Width
<1>
<0>
Antibacklash Pulse Width (ns)
0
0
1.3 (Default)
0
1
2.9
1
0
6.0
1
1
1.3
Not Used.
Digital Lock
Detect Window
<5>
Digital Lock Detect Window (ns) Digital Lock Detect Loss-of-Lock Threshold (ns)
0 (Default)
9.5
15
1
3.5
7
Digital Lock
If the time difference of the rising edges at the inputs to the PFD are less than the lock detect
Detect Window
window time, the digital lock detect flag is set. The flag remains set until the time difference is
greater than the loss-of-lock threshold.
Lock Detect
0 = Normal Lock Detect Operation (Default).
Disable
1 = Disable Lock Detect.
Not Used.
Unused
Not Used.
Rev. A | Page 49 of 60
AD9511
Reg.
Addr.
(Hex)
34
34
35
35
35
36
36
Bit(s) Name
Fine Delay Adjust
<0> Delay Control
OUT4
<7:1>
<2:0> Ramp Current
OUT4
Description
Delay Block Control Bit.
Bypasses Delay Block and Powers It Down (Default = 1b).
Not Used.
The slowest ramp (200 μs) sets the longest full scale of approximately 10 ns.
<2>
<1>
<0>
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
<5:3> Ramp Capacitor
Selects the Number of Capacitors in Ramp Generation Circuit.
OUT4
More Capacitors => Slower Ramp.
<5>
<4>
<3>
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
<7:6>
Not Used.
<0>
Not Used.
<5:1> Delay Fine Adjust Sets Delay Within Full Scale of the Ramp; There Are 32 Steps.
OUT4
00000b => Zero Delay (Default).
11111b => Maximum Delay.
36
<7:6>
37 (38) (39) <7:0>
(3A) (3B)
(3C)
3D (3E) (3F) <1:0> Power-Down
LVPECL
OUT0
(OUT1)
(OUT2)
Ramp Current (μs)
200
400
600
800
1000
1200
1400
1600
Number of Capacitors
4 (Default)
3
3
2
3
2
2
1
Not Used.
Not Used.
Mode
ON
PD1
PD2
<1>
0
0
1
<0>
0
1
0
Description
Normal Operation
Test Only—Do Not Use
Safe Power-Down
Partial Power-Down; Use If
Output Has Load Resistors
Output
ON
OFF
OFF
PD3
1
1
Total Power-Down
Use Only If Output Has No
Load Resistors
OFF
Rev. A | Page 50 of 60
AD9511
Reg.
Addr.
(Hex)
Bit(s) Name
3D (3E) (3F) <3:2> Output Level
LVPECL
OUT0
(OUT1)
(OUT2)
3D (3E) (3F) <7:4>
40 (41)
<0> Power-Down
LVDS/CMOS
OUT3
(OUT4)
40 (41)
<2:1> Output Current
Level
LVDS
OUT3
(OUT4)
40 (41)
<3>
40 (41)
<4>
LVDS/CMOS
Select
OUT3
(OUT4)
Inverted CMOS
Driver
OUT3
(OUT4)
40 (41)
<7:5>
42 (43) (44) <7:0>
45
45
45
45
45
45
45
46 (47)
(48) (49)
<0>
Description
Output Single-Ended Voltage Levels for LVPECL Outputs.
<3>
<2>
0
0
0
1
1
0
1
1
Not Used
Power-Down Bit for Both Output and LVDS Driver.
0 = LVDS/CMOS on (Default).
1 = LVDS/CMOS Power-Down.
Output Voltage (mV)
490
330
805 (Default)
650
<2>
<1>
Current (mA)
Termination (Ω)
0
0
1.75
100
0
1
3.5 (Default)
100
1
0
5.25
50
1
1
7
50
0 = LVDS (Default).
1 = CMOS.
Affects Output Only when in CMOS Mode.
0 = Disable Inverted CMOS Driver (Default).
1 = Enable Inverted CMOS Driver.
Not Used.
Not Used.
Clock Select
0: CLK2 Drives Distribution Section.
1: CLK1 Drives Distribution Section (Default).
<1> CLK1 Power-Down 1 = CLK1 Input Is Powered Down (Default = 0b).
<2> CLK2 Power-Down 1 = CLK2 Input Is Powered Down (Default = 0b).
<3> Prescaler Clock
1 = Shut Down Clock Signal to PLL Prescaler (Default = 0b).
Power-Down
<4> REFIN Power1 = Power-Down REFIN (Default = 0b).
Down
<5> All Clock Inputs
1 = Power-Down CLK1 and CLK2 Inputs and Associated Bias and Internal Clock Tree;
Power-Down
(Default = 0b).
<7:6>
Not Used.
<7:0>
Not Used.
Rev. A | Page 51 of 60
AD9511
Reg.
Addr.
(Hex)
4A
(4C)
(4E)
(50)
(52)
4A
(4C)
(4E)
(50)
(52)
4B
(4D)
(4F)
(51)
(53)
4B
(4D)
(4F)
(51)
(53)
Bit(s) Name
<3:0> Divider High
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
<7:4> Divider Low
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
<3:0> Phase Offset
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
<4> Start
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
<5> Force
4B
(4D)
(4F)
(51)
(53)
<6>
4B
(4D)
(4F)
(51)
(53)
<7>
4B
(4D)
(4F)
(51)
(53)
54 (55)
(56) (57)
58
<0>
58
<1>
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
Nosync
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
Bypass Divider
OUT0
(OUT1)
(OUT2)
(OUT3)
(OUT4)
<7:0>
Description
Number of Clock Cycles Divider Output Stays High.
Number of Clock Cycles Divider Output Stays Low.
Phase Offset (Default = 0000b).
Selects Start High or Start Low.
(Default = 0b).
Forces Individual Outputs to the State Specified in Start (Above).
This Function Requires That Nosync (Below) Also Be Set (Default = 0b).
Ignore Chip-Level Sync Signal (Default = 0b).
Bypass and Power-Down Divider Logic; Route Clock Directly to Output (Default = 0b).
Not Used.
SYNC Detect
Enable
SYNC Select
1 = Enable SYNC Detect (Default = 0b).
1 = Raise Flag if Slow Clocks Are Out-of-Sync by 0.5 to 1 High Speed Clock Cycles.
0 (Default) = Raise Flag if Slow Clocks Are Out-of-Sync by 1 to 1.5 High Speed Clock Cycles.
Rev. A | Page 52 of 60
AD9511
Reg.
Addr.
(Hex)
58
Bit(s) Name
<2> Soft SYNC
58
<3>
58
58
Dist Ref PowerDown
<4> SYNC PowerDown
<6:5> FUNCTION Pin
Select
58
59
5A
<7>
<7:0>
<0> Update Registers
5A
END
<7:1>
Description
Soft SYNC bit works the same as the FUNCTION pin when in SYNCB mode, except that this bit’s
polarity is reversed. That is, a high level forces selected outputs into a known state, and a high > low
transition triggers a sync (Default = 0b).
1 = Power-Down the References for the Distribution Section (Default = 0b).
1 = Power-Down the SYNC (Default = 0b).
<6>
<5>
Function
0
0
RESETB (Default)
0
1
SYNCB
1
0
Test Only; Do Not Use
1
1
PDB
Not Used
Not Used
1 written to this bit updates all registers and transfers all serial control port register buffer contents
to the control registers on the next rising SCLK edge. This is a self-clearing bit. 0 does not have to be
written to clear it.
Not Used.
Rev. A | Page 53 of 60
AD9511
POWER SUPPLY
The AD9511 requires a 3.3 V ± 5% power supply for VS.
The tables in the Specifications section give the performance
expected from the AD9511 with the power supply voltage
within this range. The absolute maximum range of −0.3 V to
+3.6 V, with respect to GND, must never be exceeded on
the VS pin.
Good engineering practice should be followed in the layout of
power supply traces and ground plane of the PCB. The power
supply should be bypassed on the PCB with adequate
capacitance (>10 μF). The AD9511 should be bypassed with
adequate capacitors (0.1 μF) at all power pins, as close as
possible to the part. The layout of the AD9511 evaluation board
(AD9511/PCB or AD9511-VCO/PCB) is a good example.
The AD9511 is a complex part that is programmed for its
desired operating configuration by on-chip registers. These
registers are not maintained over a shutdown of external power.
This means that the registers can lose their programmed values
if VS is lost long enough for the internal voltages to collapse.
Careful bypassing should protect the part from memory loss
under normal conditions. Nonetheless, it is important that the
VS power supply not become intermittent, or the AD9511 risks
losing its programming.
The internal bias currents of the AD9511 are set by the RSET and
CPRSET resistors. These resistors should be as close as possible to
the values given as conditions in the Specifications section
(RSET = 4.12 kΩ and CPRSET = 5.1 kΩ). These values are standard
1% resistor values and should be readily obtainable. The bias
currents set by these resistors determine the logic levels and
operating conditions of the internal blocks of the AD9511. The
performance figures given in the Specifications section assume
that these resistor values are used.
POWER MANAGEMENT
The power usage of the AD9511 can be managed to use only the
power required for the functions that are being used. Unused
features and circuitry can be powered down to save power. The
following circuit blocks can be powered down, or are powered
down when not selected (see the Register Map and Description
section):
•
The PLL section can be powered down if not needed.
•
Any of the dividers are powered down when bypassed—
equivalent to divide-by-one.
•
The adjustable delay block on OUT4 is powered down
when not selected.
•
Any output may be powered down. However, LVPECL
outputs have both a safe and an off condition. When the
LVPECL output is terminated, only the safe shutdown
should be used to protect the LVPECL output devices. This
still consumes some power.
•
The entire distribution section can be powered down when
not needed.
Powering down a functional block does not cause the
programming information for that block (in the registers) to be
lost. This means that blocks can be powered on and off without
otherwise having to reprogram the AD9511. However,
synchronization is lost. A SYNC must be issued to
resynchronize (see the Single-Chip Synchronization section).
The VCP pin is the supply pin for the charge pump (CP). The
voltage at this pin (VCP) may be from VS up to 5.5 V, as required
to match the tuning voltage range of a specific VCO/VCXO.
This voltage must never exceed the absolute maximum of 6 V.
VCP should also never be allowed to be less than −0.3 V below
VS or GND, whichever is lower.
The exposed metal paddle on the AD9511 package is an
electrical connection, as well as a thermal enhancement. For
the device to function properly, the paddle must be properly
attached to ground (GND). The PCB acts as a heat sink for the
AD9511; therefore, this GND connection should provide a
good thermal path to a larger dissipation area, such as a ground
plane on the PCB. See the layout of the AD9511 evaluation
board (AD9511/PCB or AD9511-VCO/PCB) for a good
example.
Rev. A | Page 54 of 60
AD9511
APPLICATIONS
USING THE AD9511 OUTPUTS FOR ADC CLOCK
APPLICATIONS
level, termination) should be considered when selecting the best
clocking/converter solution.
Any high speed analog-to-digital converter (ADC) is extremely
sensitive to the quality of the sampling clock provided by the
user. An ADC can be thought of as a sampling mixer; any noise,
distortion, or timing jitter on the clock is combined with the
desired signal at the A/D output. Clock integrity requirements
scale with the analog input frequency and resolution, with
higher analog input frequency applications at ≥14-bit resolution
being the most stringent. The theoretical SNR of an ADC is
limited by the ADC resolution and the jitter on the sampling
clock. Considering an ideal ADC of infinite resolution where
the step size and quantization error can be ignored, the available
SNR can be expressed approximately by
CMOS CLOCK DISTRIBUTION
⎡ 1 ⎤
SNR = 20 × log ⎢
⎥
⎣⎢ 2πft j ⎦⎥
where f is the highest analog frequency being digitized, and tj is
the rms jitter on the sampling clock. Figure 53 shows the
required sampling clock jitter as a function of the analog
frequency and effective number of bits (ENOB).
SNR = 20log10
Whenever single-ended CMOS clocking is used, some of the
following general guidelines should be followed.
Point-to-point nets should be designed such that a driver has
one receiver only on the net, if possible. This allows for simple
termination schemes and minimizes ringing due to possible
mismatched impedances on the net. Series termination at the
source is generally required to provide transmission line
matching and/or to reduce current transients at the driver. The
value of the resistor is dependent on the board design and
timing requirements (typically 10 Ω to 100 Ω is used). CMOS
outputs are limited in terms of the capacitive load or trace
length that they can drive. Typically, trace lengths less than
3 inches are recommended to preserve signal rise/fall times and
preserve signal integrity.
1
2πftj
18
CMOS
tj = 0.1ps
50pF
tj = 1ps
14
12
tj = 10ps
GND
ENOB
80
Figure 54. Series Termination of CMOS Output
10
tj = 100ps
40
8
6
tj = 1ns
4
20
1
3
10
30
100
FULL-SCALE SINE WAVE ANALOG INPUT FREQUENCY (MHz)
Figure 53. ENOB and SNR vs. Analog Input Frequency
See Application Notes AN-756 and AN-501 on the ADI website
at www.analog.com.
Termination at the far end of the PCB trace is a second option.
The CMOS outputs of the AD9511 do not supply enough
current to provide a full voltage swing with a low impedance
resistive, far-end termination, as shown in Figure 55. The farend termination network should match the PCB trace
impedance and provide the desired switching point. The
reduced signal swing can still meet receiver input requirements
in some applications. This may be useful when driving long
trace lengths on less critical nets.
Many high performance ADCs feature differential clock inputs
to simplify the task of providing the required low jitter clock on
a noisy PCB. (Distributing a single-ended clock on a noisy PCB
can result in coupled noise on the sample clock. Differential
distribution has inherent common-mode rejection, which can
provide superior clock performance in a noisy environment.)
The AD9511 features both LVPECL and LVDS outputs that
provide differential clock outputs, which enable clock solutions
that maximize converter SNR performance. The input
requirements of the ADC (differential or single-ended, logic
Rev. A | Page 55 of 60
VPULLUP = 3.3V
10Ω
50Ω
100Ω
CMOS
OUT3, OUT4
SELECTED AS CMOS
100Ω
Figure 55. CMOS Output with Far-End Termination
3pF
05286-097
60
05286-024
SNR (dB)
MICROSTRIP
16
100
60.4Ω
1.0 INCH
10Ω
05286-096
tj = 50fs
120
The AD9511 provides two clock outputs (OUT3 and OUT4),
which are selectable as either CMOS or LVDS levels. When
selected as CMOS, these outputs provide for driving devices
requiring CMOS level logic at their clock inputs.
AD9511
Because of the limitations of single-ended CMOS clocking,
consider using differential outputs when driving high speed
signals over long traces. The AD9511 offers both LVPECL and
LVDS outputs, which are better suited for driving long traces
where the inherent noise immunity of differential signaling
provides superior performance for clocking converters.
LVPECL CLOCK DISTRIBUTION
The low voltage, positive emitter-coupled, logic (LVPECL)
outputs of the AD9511 provide the lowest jitter clock signals
available from the AD9511. The LVPECL outputs (because they
are open emitter) require a dc termination to bias the output
transistors. A simplified equivalent circuit in Figure 41 shows
the LVPECL output stage.
LVDS CLOCK DISTRIBUTION
Low voltage differential signaling (LVDS) is a second
differential output option for the AD9511. LVDS uses a current
mode output stage with several user-selectable current levels.
The normal value (default) for this current is 3.5 mA, which
yields 350 mV output swing across a 100 Ω resistor. The LVDS
outputs meet or exceed all ANSI/TIA/EIA—644 specifications.
A recommended termination circuit for the LVDS outputs is
shown in Figure 58.
3.3V
LVDS
3.3V
100Ω
100Ω
DIFFERENTIAL (COUPLED)
Figure 58. LVDS Output Termination
3.3V
3.3V
50Ω
LVPECL
127Ω
127Ω
SINGLE-ENDED
(NOT COUPLED)
3.3V
See Application Note AN-586 on the ADI website at
www.analog.com for more information on LVDS.
LVPECL
POWER AND GROUNDING CONSIDERATIONS AND
POWER SUPPLY REJECTION
50Ω
83Ω
83Ω
05286-030
VT = VCC – 1.3V
Figure 56. LVPECL Far-End Termination
3.3V
3.3V
Many applications seek high speed and performance under less
than ideal operating conditions. In these application circuits,
the implementation and construction of the PCB is as
important as the circuit design. Proper RF techniques must be
used for device selection, placement, and routing, as well as for
power supply bypassing and grounding to ensure optimum
performance.
0.1nF
200Ω
0.1nF
DIFFERENTIAL
(COUPLED)
100Ω
LVPECL
200Ω
05286-031
LVPECL
LVDS
05286-032
In most applications, a standard LVPECL far-end termination is
recommended, as shown in Figure 56. The resistor network is
designed to match the transmission line impedance (50 Ω) and
the desired switching threshold (1.3 V).
Figure 57. LVPECL with Parallel Transmission Line
Rev. A | Page 56 of 60
AD9511
OUTLINE DIMENSIONS
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
36
PIN 1
INDICATOR
TOP
VIEW
12° MAX
PIN 1
INDICATOR
48
1
EXPOSED
PAD
6.75
BSC SQ
5.25
5.10 SQ
4.95
(BOTTOM VIEW)
0.50
0.40
0.30
1.00
0.85
0.80
0.30
0.23
0.18
25
24
12
13
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 59. 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
7 mm × 7 mm Body, Very Thin Quad
(CP-48-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9511BCPZ 1
AD9511BCPZ-REEL71
AD9511/PCB
AD9511-VCO/PCB
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
48-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
48-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
Evaluation Board without VCO, VCXO, or Loop Filter
Evaluation Board with 245.76 MHz VCXO, Loop Filter
Z = Pb-free part.
Rev. A | Page 57 of 60
Package Option
CP-48-1
CP-48-1
AD9511
NOTES
Rev. A | Page 58 of 60
AD9511
NOTES
Rev. A | Page 59 of 60
AD9511
NOTES
©2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05286–0–6/05(A)
Rev. A | Page 60 of 60