REJ09B0303-0300 The revision list can be viewed directly by clicking the title page. The revision list summarizes the locations of revisions and additions. Details should always be checked by referring to the relevant text. 8 H8/3577 Group, H8/3567 Group Hardware Manual Renesas 8-Bit Single-Chip Microcomputer H8 Family/H8/300 Series H8/3577 H8/3574 H8/3567 H8/3564 H8/3567U H8/3564U Rev. 3.00 Revision Date: Mar 17, 2006 HD6433577 HD6473577 HD6433574 HD6433567 HD6473567 HD6433564 HD6433567U HD6473567U HD6433564U Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any thirdparty's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. Rev. 3.00 Mar 17, 2006 page ii of xxiv General Precautions on Handling of Product 1. Treatment of NC Pins Note: Do not connect anything to the NC pins. The NC (not connected) pins are either not connected to any of the internal circuitry or are used as test pins or to reduce noise. If something is connected to the NC pins, the operation of the LSI is not guaranteed. 2. Treatment of Unused Input Pins Note: Fix all unused input pins to high or low level. Generally, the input pins of CMOS products are high-impedance input pins. If unused pins are in their open states, intermediate levels are induced by noise in the vicinity, a passthrough current flows internally, and a malfunction may occur. 3. Processing before Initialization Note: When power is first supplied, the product’s state is undefined. The states of internal circuits are undefined until full power is supplied throughout the chip and a low level is input on the reset pin. During the period where the states are undefined, the register settings and the output state of each pin are also undefined. Design your system so that it does not malfunction because of processing while it is in this undefined state. For those products which have a reset function, reset the LSI immediately after the power supply has been turned on. 4. Prohibition of Access to Undefined or Reserved Addresses Note: Access to undefined or reserved addresses is prohibited. The undefined or reserved addresses may be used to expand functions, or test registers may have been be allocated to these addresses. Do not access these registers; the system’s operation is not guaranteed if they are accessed. Rev. 3.00 Mar 17, 2006 page iii of xxiv Configuration of This Manual This manual comprises the following items: 1. General Precautions on Handling of Product 2. Configuration of This Manual 3. Preface 4. Main Revisions for This Edition The list of revisions is a summary of points that have been revised or added to earlier versions. This does not include all of the revised contents. For details, see the actual locations in this manual. 5. Contents 6. Overview 7. Description of Functional Modules • CPU and System-Control Modules • On-Chip Peripheral Modules The configuration of the functional description of each module differs according to the module. However, the generic style includes the following items: i) Feature ii) Input/Output Pin iii) Register Description iv) Operation v) Usage Note When designing an application system that includes this LSI, take notes into account. Each section includes notes in relation to the descriptions given, and usage notes are given, as required, as the final part of each section. 8. List of Registers 9. Electrical Characteristics 10. Appendix Rev. 3.00 Mar 17, 2006 page iv of xxiv Preface The H8/3577 Group and H8/3567 Group comprise single-chip microcomputers built around the H8/300 CPU and equipped with on-chip supporting functions required for system configuration. Versions are available with PROM (ZTAT™) or mask ROM as on-chip ROM. On-chip supporting functions include a16-bit free-running timer (FRT), 8-bit timer (TMR), watchdog timer (WDT), two PWM timers (PWM and PWMX), a serial communication interface 2 (SCI), I C bus interface (IIC), A/D converter (ADC), and I/O ports. The H8/3577 Group comprises 64-pin models with the above supporting functions on-chip. The H8/3567 Group comprises the 42-pin H8/3567 and H8/3564 with fewer PWM, ADC, and I/O port channels, and the 64-pin H8/3567U and H8/3564U with on-chip universal serial bus (USB) hubs and function. Use of the H8/3577 Group or H8/3567 Group enables compact, high-performance systems to be implemented easily. The comprehensive timer functions and their interconnectability (timer connection facility) make these groups ideal for applications such as PC monitor systems. This manual describes the hardware of the H8/3577 Group and H8/3567 Group. Refer to the H8/300 Series Programming Manual for a detailed description of the instruction set. Note: ZTAT (Zero Turn-Around Time) is a trademark of Renesas Technology Corp. Rev. 3.00 Mar 17, 2006 page v of xxiv On-Chip Supporting Modules Group H8/3577 Group H8/3567 Group Product names H8/3577, H8/3574 H8/3567, H8/3564, H8/3567U, H8/3564U Universal serial bus (USB) — —/Available (H8/3567U, H8/3564U) 8-bit PWM timer (PWM) ×16 ×8 14-bit PWM timer (PWMX) ×2 ×2 16-bit free-running timer (FRT) ×1 ×1 8-bit timer (TMR) ×4 ×4 Timer connection Available Available Watchdog timer (WDT) ×1 ×1 Serial communication interface (SCI) ×1 ×1 I C bus interface (IIC) ×2 ×2 A/D converter ×8 ×4 2 Rev. 3.00 Mar 17, 2006 page vi of xxiv Main Revisions in This Edition Item Page Revision (See Manual for Details) All — • Notification of change in company name amended (Before) Hitachi, Ltd. → (After) Renesas Technology Corp. • Product naming convention amended (Before) H8/3577 Series → (After) H8/3577 Group (Before) H8/3567 Series → (After) H8/3567 Group 5.2.1 System Control Register (SYSCR) 84 Bit table amended Bit ... ... 7.3.5 Operation when 155 OUT Token Is Received (Endpoints 0 and 2) 4 ... INTM0 ... Initial value 0 Read/Write R Figure amended Clear EP2TS bit to 0 in TSFR Figure 7.3 (2) Operation when OUT Token Is Received (EP2-OUT: Initial FIFO Full) (cont) 7.3.9 USB Module Startup Sequence 164 Description amended 8. After DPLL operation stabilization time, HSRST bit is cleared to 0 by firmware Initial Operation Procedures: Figure 7.5 USB Hub Initial Operation Procedure 165 Figure 7.6 USB Function Initial Operation Procedure 166 Figure amended Clear FONLY bit to 0 in USBCR Figure amended (Wait for USB operating clock oscillation stabilization time (10 ms)) Clear FPLLRST bit to 0 in USBCR Rev. 3.00 Mar 17, 2006 page vii of xxiv Item Page Revision (See Manual for Details) 7.3.9 USB Module Startup Sequence 167 Figure amended Figure 7.6 USB Function Initial Operation Procedure (cont) Set EPIVLD bit to 1 in USBCSR0 Figure 7.9 USB Function Standalone Mode Upstream Disconnection/ Reconnection 172 12.2.8 Timer Connection Register S (TCONRS) 296 2 16.3.1 I C Bus Data Format Figure amended Set EPIVLD bit to 1 in USBCSR0 Table amended Bit 7 TMRX/Y Accessible Registers H'FFF0 H'FFF1 H'FFF2 H'FFF3 H'FFF4 0 TCRX (Initial value) (TMRX) TCSRX (TMRX) TICRR (TMRX) TICRF (TMRX) TCNTX TCORC TCORAX TCORBX (TMRX) (TMRX) (TMRX) (TMRX) 1 TCSRY (TMRY) TCORAY TCORBY TCNTY TISR (TMRY) (TMRY) (TMRY) (TMRY) TCRY (TMRY) 447 Newly added 579 Table amended Table 16.4 2 Description of I C Bus Data Format Symbols B.1 Addresses Register Address Name B.3 Functions H'FFE2 ADDRBH H'FFE3 ADDRBL H'FFE4 ADDRCH H'FFE5 ADDRCL H'FFE6 ADDRDH H'FFE7 ADDRDL 587 Bit table added 606 Bit table added UTESTR0, UTESTR1 UTESTR2 Rev. 3.00 Mar 17, 2006 page viii of xxiv ... Module Name Bus Width A/D 8 H'FFF5 H'FFF6 H'FFF7 Item Page Revision (See Manual for Details) Appendix G Package Dimensions 703 Figure replaced Figure G.2 FP-64A Package Dimensions 704 Figure replaced Figure G.3 DP-42S Package Dimensions 705 Figure replaced Figure G.4 FP-44A Package Dimensions 706 Figure replaced Figure G.1 DP-64S Package Dimensions Rev. 3.00 Mar 17, 2006 page ix of xxiv Rev. 3.00 Mar 17, 2006 page x of xxiv Contents Section 1 Overview ............................................................................................................. 1.1 1.2 1.3 1 Overview........................................................................................................................... 1 Internal Block Diagrams ................................................................................................... 6 Pin Arrangement and Functions........................................................................................ 8 1.3.1 Pin Arrangement .................................................................................................. 8 1.3.2 List of Pin Functions............................................................................................ 14 1.3.3 Pin Functions ....................................................................................................... 22 Section 2 CPU ...................................................................................................................... 29 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Overview........................................................................................................................... 2.1.1 Features................................................................................................................ 2.1.2 Address Space...................................................................................................... 2.1.3 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 2.2.1 General Registers ................................................................................................. 2.2.2 Control Registers ................................................................................................. 2.2.3 Initial Register Values.......................................................................................... Data Formats..................................................................................................................... 2.3.1 Data Formats in General Registers ...................................................................... 2.3.2 Memory Data Formats ......................................................................................... Addressing Modes ............................................................................................................ 2.4.1 Addressing Modes ............................................................................................... 2.4.2 Effective Address Calculation ............................................................................. Instruction Set ................................................................................................................... 2.5.1 Data Transfer Instructions.................................................................................... 2.5.2 Arithmetic Operations.......................................................................................... 2.5.3 Logic Operations.................................................................................................. 2.5.4 Shift Operations ................................................................................................... 2.5.5 Bit Manipulations................................................................................................. 2.5.6 Branching Instructions ......................................................................................... 2.5.7 System Control Instructions................................................................................. 2.5.8 Block Data Transfer Instruction........................................................................... Basic Operational Timing ................................................................................................. 2.6.1 Access to On-Chip Memory (RAM, ROM)......................................................... 2.6.2 Access to On-Chip Peripheral Modules............................................................... CPU States ........................................................................................................................ 2.7.1 Overview.............................................................................................................. 2.7.2 Reset State............................................................................................................ 29 29 30 30 31 31 31 33 33 34 35 36 36 38 42 44 46 47 47 49 53 55 57 58 58 59 60 60 61 Rev. 3.00 Mar 17, 2006 page xi of xxiv 2.8 2.7.3 Program Execution State...................................................................................... 2.7.4 Program Halt State............................................................................................... 2.7.5 Exception-Handling State .................................................................................... Application Notes ............................................................................................................. 2.8.1 Notes on Bit Manipulation................................................................................... 2.8.2 Notes on Use of the EEPMOV Instruction (Cannot Be Used in the H8/3577 Group and H8/3567 Group) ............................ 61 61 61 62 62 64 Section 3 MCU Operating Modes .................................................................................. 65 3.1 3.2 3.3 Overview........................................................................................................................... 3.1.1 Operating Mode Selection ................................................................................... 3.1.2 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 3.2.1 Mode Control Register (MDCR) ......................................................................... 3.2.2 System Control Register (SYSCR) ...................................................................... 3.2.3 Serial Timer Control Register (STCR) ................................................................ Address Map ..................................................................................................................... 65 65 65 66 66 67 68 69 Section 4 Exception Handling ......................................................................................... 73 4.1 4.2 4.3 4.4 4.5 Overview........................................................................................................................... 4.1.1 Exception Handling Types and Priority............................................................... 4.1.2 Exception Handling Operation............................................................................. 4.1.3 Exception Sources and Vector Table ................................................................... Reset.................................................................................................................................. 4.2.1 Overview.............................................................................................................. 4.2.2 Reset Sequence .................................................................................................... 4.2.3 Interrupts after Reset............................................................................................ Interrupts ........................................................................................................................... Stack Status after Exception Handling.............................................................................. Note on Stack Handling .................................................................................................... 73 73 73 74 75 75 75 76 77 78 79 Section 5 Interrupt Controller .......................................................................................... 81 5.1 5.2 Overview........................................................................................................................... 5.1.1 Features................................................................................................................ 5.1.2 Block Diagram ..................................................................................................... 5.1.3 Pin Configuration................................................................................................. 5.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 5.2.1 System Control Register (SYSCR) ...................................................................... 5.2.2 IRQ Enable Register (IER) .................................................................................. 5.2.3 IRQ Sense Control Registers H and L (ISCRH, ISCRL)..................................... Rev. 3.00 Mar 17, 2006 page xii of xxiv 81 81 82 83 83 84 84 85 86 5.3 5.4 5.5 5.2.4 IRQ Status Register (ISR).................................................................................... Interrupt Sources............................................................................................................... 5.3.1 External Interrupts ............................................................................................... 5.3.2 Internal Interrupts................................................................................................. 5.3.3 Interrupt Exception Vector Table ........................................................................ Interrupt Operation............................................................................................................ 5.4.1 Interrupt Operation .............................................................................................. 5.4.2 Interrupt Control Mode 0 ..................................................................................... 5.4.3 Interrupt Exception Handling Sequence .............................................................. 5.4.4 Interrupt Response Times .................................................................................... Usage Notes ...................................................................................................................... 5.5.1 Contention between Interrupt Generation and Disabling..................................... 5.5.2 Instructions that Disable Interrupts ...................................................................... 5.5.3 Interrupts during Execution of EEPMOV Instruction.......................................... 87 88 88 89 89 92 92 94 96 97 98 98 99 99 Section 6 Bus Controller ................................................................................................... 101 6.1 6.2 Overview........................................................................................................................... Register Descriptions ........................................................................................................ 6.2.1 Bus Control Register (BCR) ................................................................................ 6.2.2 Wait State Control Register (WSCR) .................................................................. 101 101 101 102 Section 7 Universal Serial Bus Interface (USB)......................................................... 103 7.1 7.2 Overview........................................................................................................................... 7.1.1 Features................................................................................................................ 7.1.2 Block Diagram ..................................................................................................... 7.1.3 Pin Configuration................................................................................................. 7.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 7.2.1 USB Data FIFO.................................................................................................... 7.2.2 Endpoint Size Register 1 (EPSZR1) .................................................................... 7.2.3 Endpoint Data Registers 0I, 0O, 1, 2 (EPDR0I, EPDR0O, EPDR1, EPDR2) ..... 7.2.4 FIFO Valid Size Registers 0I, 0O, 1, 2 (FVSR0I, FVSR0O, FVSR1, FVSR2)... 7.2.5 Endpoint Direction Register (EPDIR) ................................................................. 7.2.6 Packet Transmit Enable Register (PTTER) ......................................................... 7.2.7 USB Interrupt Enable Register (USBIER)........................................................... 7.2.8 USB Interrupt Flag Register (USBIFR) ............................................................... 7.2.9 Transfer Success Flag Register (TSFR) ............................................................... 7.2.10 Transfer Fail Flag Register (TFFR) ..................................................................... 7.2.11 USB Control/Status Register 0 (USBCSR0)........................................................ 7.2.12 Endpoint Stall Register (EPSTLR) ...................................................................... 7.2.13 Endpoint Reset Register (EPRSTR)..................................................................... 103 103 104 105 105 107 107 108 109 110 111 112 113 115 118 121 124 128 129 Rev. 3.00 Mar 17, 2006 page xiii of xxiv 7.3 7.2.14 Device Resume Register (DEVRSMR) ............................................................... 7.2.15 Interrupt Source Select Register 0 (INTSELR0).................................................. 7.2.16 Interrupt Source Select Register 1 (INTSELR1).................................................. 7.2.17 Hub Overcurrent Control Register (HOCCR)...................................................... 7.2.18 USB Control Register (USBCR).......................................................................... 7.2.19 USB PLL Control Register (UPLLCR) ............................................................... 7.2.20 USB Port Control Register (UPRTCR)................................................................ 7.2.21 USB Test Registers 2, 1, 0 (UTESTR2, UTESTR1, UTESTR0)......................... 7.2.22 Module Stop Control Register (MSTPCR) .......................................................... 7.2.23 Serial Timer Control Register (STCR) ................................................................ Operation .......................................................................................................................... 7.3.1 USB Compound Device Configuration ............................................................... 7.3.2 Functions of USB Hub Block .............................................................................. 7.3.3 Functions of USB Function ................................................................................. 7.3.4 Operation when SETUP Token Is Received (Endpoint 0)................................... 7.3.5 Operation when OUT Token Is Received (Endpoints 0 and 2) ........................... 7.3.6 Operation when IN Token Is Received (Endpoints 0, 1, and 2) .......................... 7.3.7 Suspend/Resume Operations................................................................................ 7.3.8 USB Module Reset and Operation-Halted States ................................................ 7.3.9 USB Module Startup Sequence............................................................................ 7.3.10 USB Module Slave CPU Interrupts ..................................................................... 131 131 133 133 135 139 141 142 143 143 145 145 145 146 148 153 155 159 159 162 175 Section 8 I/O Ports .............................................................................................................. 177 8.1 8.2 8.3 8.4 8.5 Overview........................................................................................................................... Port 1................................................................................................................................. 8.2.1 Overview.............................................................................................................. 8.2.2 Register Configuration......................................................................................... 8.2.3 Pin Functions ....................................................................................................... 8.2.4 MOS Input Pull-Up Function............................................................................... Port 2 [H8/3577 Group Only] ........................................................................................... 8.3.1 Overview.............................................................................................................. 8.3.2 Register Configuration......................................................................................... 8.3.3 Pin Functions ....................................................................................................... 8.3.4 MOS Input Pull-Up Function............................................................................... Port 3 [H8/3577 Group Only] ........................................................................................... 8.4.1 Overview.............................................................................................................. 8.4.2 Register Configuration......................................................................................... 8.4.3 Pin Functions ....................................................................................................... 8.4.4 MOS Input Pull-Up Function............................................................................... Port 4................................................................................................................................. 8.5.1 Overview.............................................................................................................. Rev. 3.00 Mar 17, 2006 page xiv of xxiv 177 180 180 181 182 185 186 186 187 189 191 192 192 192 194 194 195 195 8.5.2 Register Configuration......................................................................................... 8.5.3 Pin Functions ....................................................................................................... 8.6 Port 5................................................................................................................................. 8.6.1 Overview.............................................................................................................. 8.6.2 Register Configuration......................................................................................... 8.6.3 Pin Functions ....................................................................................................... 8.7 Port 6................................................................................................................................. 8.7.1 Overview.............................................................................................................. 8.7.2 Register Configuration......................................................................................... 8.7.3 Pin Functions ....................................................................................................... 8.8 Port 7................................................................................................................................. 8.8.1 Overview.............................................................................................................. 8.8.2 Register Configuration......................................................................................... 8.8.3 Pin Functions ....................................................................................................... 8.9 Port C [H8/3567 Group Version with On-Chip USB Only] ............................................. 8.9.1 Overview.............................................................................................................. 8.9.2 Register Configuration......................................................................................... 8.9.3 Pin Functions ....................................................................................................... 8.10 Port D [H8/3567 Group Version with On-Chip USB Only] ............................................. 8.10.1 Overview.............................................................................................................. 8.10.2 Register Configuration......................................................................................... 8.10.3 Pin Functions ....................................................................................................... 195 197 199 199 199 201 202 202 202 203 206 206 206 207 208 208 208 210 211 211 211 213 Section 9 8-Bit PWM Timers........................................................................................... 215 9.1 9.2 9.3 Overview........................................................................................................................... 9.1.1 Features................................................................................................................ 9.1.2 Block Diagram ..................................................................................................... 9.1.3 Pin Configuration................................................................................................. 9.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 9.2.1 PWM Register Select (PWSL)............................................................................. 9.2.2 PWM Data Registers (PWDR0 to PWDR15) ...................................................... 9.2.3 PWM Data Polarity Registers A and B (PWDPRA and PWDPRB).................... 9.2.4 PWM Output Enable Registers A and B (PWOERA and PWOERB) ................. 9.2.5 Peripheral Clock Select Register (PCSR) ............................................................ 9.2.6 Port 1 Data Direction Register (P1DDR)............................................................. 9.2.7 Port 2 Data Direction Register (P2DDR)............................................................. 9.2.8 Port 1 Data Register (P1DR)................................................................................ 9.2.9 Port 2 Data Register (P2DR)................................................................................ 9.2.10 Module Stop Control Register (MSTPCR) .......................................................... Operation .......................................................................................................................... 215 215 216 217 217 218 218 220 220 221 222 222 223 223 223 224 225 Rev. 3.00 Mar 17, 2006 page xv of xxiv 9.3.1 Correspondence between PWM Data Register Contents and Output Waveform.......................................................................................... 225 Section 10 14-Bit PWM Timer ........................................................................................ 227 10.1 Overview........................................................................................................................... 10.1.1 Features................................................................................................................ 10.1.2 Block Diagram ..................................................................................................... 10.1.3 Pin Configuration................................................................................................. 10.1.4 Register Configuration......................................................................................... 10.2 Register Descriptions ........................................................................................................ 10.2.1 PWM D/A Counter (DACNT) ............................................................................. 10.2.2 D/A Data Registers A and B (DADRA and DADRB)......................................... 10.2.3 PWM D/A Control Register (DACR) .................................................................. 10.2.4 Module Stop Control Register (MSTPCR) .......................................................... 10.3 Bus Master Interface ......................................................................................................... 10.4 Operation .......................................................................................................................... 227 227 228 229 229 230 230 231 232 234 235 238 Section 11 16-Bit Free-Running Timer......................................................................... 243 11.1 Overview........................................................................................................................... 11.1.1 Features................................................................................................................ 11.1.2 Block Diagram ..................................................................................................... 11.1.3 Input and Output Pins .......................................................................................... 11.1.4 Register Configuration......................................................................................... 11.2 Register Descriptions ........................................................................................................ 11.2.1 Free-Running Counter (FRC) .............................................................................. 11.2.2 Output Compare Registers A and B (OCRA, OCRB) ......................................... 11.2.3 Input Capture Registers A to D (ICRA to ICRD) ................................................ 11.2.4 Output Compare Registers AR and AF (OCRAR, OCRAF) ............................... 11.2.5 Output Compare Register DM (OCRDM) ........................................................... 11.2.6 Timer Interrupt Enable Register (TIER) .............................................................. 11.2.7 Timer Control/Status Register (TCSR) ................................................................ 11.2.8 Timer Control Register (TCR) ............................................................................. 11.2.9 Timer Output Compare Control Register (TOCR) .............................................. 11.2.10 Module Stop Control Register (MSTPCR) .......................................................... 11.3 Operation .......................................................................................................................... 11.3.1 FRC Increment Timing ........................................................................................ 11.3.2 Output Compare Output Timing .......................................................................... 11.3.3 FRC Clear Timing................................................................................................ 11.3.4 Input Capture Input Timing ................................................................................. 11.3.5 Timing of Input Capture Flag (ICFA to ICFD) Setting ....................................... 11.3.6 Setting of Output Compare Flags A and B (OCFA, OCFB)................................ Rev. 3.00 Mar 17, 2006 page xvi of xxiv 243 243 244 245 246 247 247 247 248 249 250 250 252 255 257 260 260 260 262 263 263 266 267 11.3.7 Setting of FRC Overflow Flag (OVF) ................................................................. 11.3.8 Automatic Addition of OCRA and OCRAR/OCRAF ......................................... 11.3.9 ICRD and OCRDM Mask Signal Generation ...................................................... 11.4 Interrupts ........................................................................................................................... 11.5 Sample Application........................................................................................................... 11.6 Usage Notes ...................................................................................................................... 268 268 269 270 271 272 Section 12 8-Bit Timers ..................................................................................................... 12.1 Overview........................................................................................................................... 12.1.1 Features................................................................................................................ 12.1.2 Block Diagram ..................................................................................................... 12.1.3 Pin Configuration................................................................................................. 12.1.4 Register Configuration......................................................................................... 12.2 Register Descriptions ........................................................................................................ 12.2.1 Timer Counter (TCNT)........................................................................................ 12.2.2 Time Constant Register A (TCORA)................................................................... 12.2.3 Time Constant Register B (TCORB) ................................................................... 12.2.4 Timer Control Register (TCR) ............................................................................. 12.2.5 Timer Control/Status Register (TCSR) ................................................................ 12.2.6 Serial Timer Control Register (STCR) ................................................................ 12.2.7 System Control Register (SYSCR) ...................................................................... 12.2.8 Timer Connection Register S (TCONRS)............................................................ 12.2.9 Input Capture Register (TICR) [TMRX Additional Function] ............................ 12.2.10 Time Constant Register C (TCORC) [TMRX Additional Function]................... 12.2.11 Input Capture Registers R and F (TICRR, TICRF) [TMRX Additional Functions]............................................................................. 12.2.12 Timer Input Select Register (TISR) [TMRY Additional Function]..................... 12.2.13 Module Stop Control Register (MSTPCR) .......................................................... 12.3 Operation .......................................................................................................................... 12.3.1 TCNT Incrementation Timing ............................................................................. 12.3.2 Compare-Match Timing....................................................................................... 12.3.3 TCNT External Reset Timing .............................................................................. 12.3.4 Timing of Overflow Flag (OVF) Setting ............................................................. 12.3.5 Operation with Cascaded Connection.................................................................. 12.4 Interrupt Sources............................................................................................................... 12.5 8-Bit Timer Application Example..................................................................................... 12.6 Usage Notes ...................................................................................................................... 12.6.1 Contention between TCNT Write and Clear........................................................ 12.6.2 Contention between TCNT Write and Increment ................................................ 12.6.3 Contention between TCOR Write and Compare-Match ...................................... 12.6.4 Contention between Compare-Matches A and B................................................. 279 279 279 280 281 282 283 283 284 285 286 290 294 295 295 296 296 297 297 298 299 299 300 302 302 303 304 305 306 306 307 308 309 Rev. 3.00 Mar 17, 2006 page xvii of xxiv 12.6.5 Switching of Internal Clocks and TCNT Operation............................................. 309 Section 13 Timer Connection........................................................................................... 13.1 Overview........................................................................................................................... 13.1.1 Features................................................................................................................ 13.1.2 Block Diagram ..................................................................................................... 13.1.3 Input and Output Pins .......................................................................................... 13.1.4 Register Configuration......................................................................................... 13.2 Register Descriptions ........................................................................................................ 13.2.1 Timer Connection Register I (TCONRI) ............................................................. 13.2.2 Timer Connection Register O (TCONRO) .......................................................... 13.2.3 Timer Connection Register S (TCONRS)............................................................ 13.2.4 Edge Sense Register (SEDGR) ............................................................................ 13.2.5 Module Stop Control Register (MSTPCR) .......................................................... 13.3 Operation .......................................................................................................................... 13.3.1 PWM Decoding (PDC Signal Generation) .......................................................... 13.3.2 Clamp Waveform Generation (CL1/CL2/CL3 Signal Generation) ........................ 13.3.3 Measurement of 8-Bit Timer Divided Waveform Period .................................... 13.3.4 IHI Signal and 2fH Modification ......................................................................... 13.3.5 IVI Signal Fall Modification and IHI Synchronization ....................................... 13.3.6 Internal Synchronization Signal Generation (IHG/IVG/CL4 Signal Generation) 13.3.7 HSYNCO Output ................................................................................................. 13.3.8 VSYNCO Output ................................................................................................. 13.3.9 CBLANK Output ................................................................................................. 313 313 313 314 315 316 316 316 318 320 323 325 327 327 328 330 332 334 336 339 340 341 Section 14 Watchdog Timer (WDT) .............................................................................. 343 14.1 Overview........................................................................................................................... 14.1.1 Features................................................................................................................ 14.1.2 Block Diagram ..................................................................................................... 14.1.3 Register Configuration......................................................................................... 14.2 Register Descriptions ........................................................................................................ 14.2.1 Timer Counter (TCNT)........................................................................................ 14.2.2 Timer Control/Status Register (TCSR0) .............................................................. 14.2.3 System Control Register (SYSCR) ...................................................................... 14.2.4 Notes on Register Access..................................................................................... 14.3 Operation .......................................................................................................................... 14.3.1 Watchdog Timer Operation ................................................................................. 14.3.2 Interval Timer Operation ..................................................................................... 14.3.3 Timing of Setting of Overflow Flag (OVF) ......................................................... 14.4 Interrupts ........................................................................................................................... 14.5 Usage Notes ...................................................................................................................... Rev. 3.00 Mar 17, 2006 page xviii of xxiv 343 343 344 345 345 345 346 348 349 349 349 350 351 352 352 14.5.1 Contention between Timer Counter (TCNT) Write and Increment ..................... 352 14.5.2 Changing Value of CKS2 to CKS0...................................................................... 353 14.5.3 Switching between Watchdog Timer Mode and Interval Timer Mode................ 353 Section 15 Serial Communication Interface (SCI) .................................................... 355 15.1 Overview........................................................................................................................... 15.1.1 Features................................................................................................................ 15.1.2 Block Diagram ..................................................................................................... 15.1.3 Pin Configuration................................................................................................. 15.1.4 Register Configuration......................................................................................... 15.2 Register Descriptions ........................................................................................................ 15.2.1 Receive Shift Register (RSR) .............................................................................. 15.2.2 Receive Data Register (RDR) .............................................................................. 15.2.3 Transmit Shift Register (TSR) ............................................................................. 15.2.4 Transmit Data Register (TDR)............................................................................. 15.2.5 Serial Mode Register (SMR)................................................................................ 15.2.6 Serial Control Register (SCR).............................................................................. 15.2.7 Serial Status Register (SSR) ................................................................................ 15.2.8 Bit Rate Register (BRR) ...................................................................................... 15.2.9 Serial Interface Mode Register (SCMR).............................................................. 15.2.10 Module Stop Control Register (MSTPCR) .......................................................... 15.3 Operation .......................................................................................................................... 15.3.1 Overview.............................................................................................................. 15.3.2 Operation in Asynchronous Mode ....................................................................... 15.3.3 Multiprocessor Communication Function............................................................ 15.3.4 Operation in Synchronous Mode ......................................................................... 15.4 SCI Interrupts.................................................................................................................... 15.5 Usage Notes ...................................................................................................................... 355 355 357 358 358 359 359 359 360 360 360 363 367 371 380 381 382 382 384 395 403 412 413 Section 16 I2C Bus Interface (IIC) .................................................................................. 417 16.1 Overview........................................................................................................................... 16.1.1 Features................................................................................................................ 16.1.2 Block Diagram ..................................................................................................... 16.1.3 Input/Output Pins ................................................................................................. 16.1.4 Register Configuration......................................................................................... 16.2 Register Descriptions ........................................................................................................ 2 16.2.1 I C Bus Data Register (ICDR) ............................................................................. 16.2.2 Slave Address Register (SAR) ............................................................................. 16.2.3 Second Slave Address Register (SARX) ............................................................. 2 16.2.4 I C Bus Mode Register (ICMR) ........................................................................... 2 16.2.5 I C Bus Control Register (ICCR) ......................................................................... 417 417 418 420 421 422 422 425 427 428 430 Rev. 3.00 Mar 17, 2006 page xix of xxiv 2 16.2.6 I C Bus Status Register (ICSR)............................................................................ 16.2.7 Serial Timer Control Register (STCR) ................................................................ 16.2.8 DDC Switch Register (DDCSWR) ...................................................................... 16.2.9 Module Stop Control Register (MSTPCR) .......................................................... 16.3 Operation .......................................................................................................................... 2 16.3.1 I C Bus Data Format ............................................................................................ 16.3.2 Master Transmit Operation .................................................................................. 16.3.3 Master Receive Operation.................................................................................... 16.3.4 Slave Receive Operation...................................................................................... 16.3.5 Slave Transmit Operation .................................................................................... 16.3.6 IRIC Setting Timing and SCL Control ................................................................ 2 16.3.7 Automatic Switching from Formatless Mode to I C Bus Format ........................ 16.3.8 Noise Canceler ..................................................................................................... 16.3.9 Sample Flowcharts............................................................................................... 16.3.10 Initialization of Internal State .............................................................................. 16.4 Usage Notes ...................................................................................................................... 436 441 442 445 446 446 448 450 452 455 457 458 459 459 463 465 Section 17 A/D Converter ................................................................................................. 471 17.1 Overview........................................................................................................................... 17.1.1 Features................................................................................................................ 17.1.2 Block Diagram ..................................................................................................... 17.1.3 Pin Configuration................................................................................................. 17.1.4 Register Configuration......................................................................................... 17.2 Register Descriptions ........................................................................................................ 17.2.1 A/D Data Registers A to D (ADDRA to ADDRD).............................................. 17.2.2 A/D Control/Status Register (ADCSR) ............................................................... 17.2.3 A/D Control Register (ADCR) ............................................................................ 17.2.4 Module Stop Control Register (MSTPCR) .......................................................... 17.3 Interface to Bus Master ..................................................................................................... 17.4 Operation .......................................................................................................................... 17.4.1 Single Mode (SCAN = 0) .................................................................................... 17.4.2 Scan Mode (SCAN = 1)....................................................................................... 17.4.3 Input Sampling and A/D Conversion Time ......................................................... 17.4.4 External Trigger Input Timing............................................................................. 17.5 Interrupts ........................................................................................................................... 17.6 Usage Notes ...................................................................................................................... 471 471 472 473 474 474 474 475 478 479 480 481 481 483 485 486 486 487 Section 18 RAM .................................................................................................................. 493 18.1 Overview........................................................................................................................... 493 18.1.1 Block Diagram ..................................................................................................... 493 18.1.2 Register Configuration......................................................................................... 494 Rev. 3.00 Mar 17, 2006 page xx of xxiv 18.2 System Control Register (SYSCR) ................................................................................... 494 18.3 Operation .......................................................................................................................... 494 Section 19 ROM .................................................................................................................. 495 19.1 Overview........................................................................................................................... 495 19.2 Operation .......................................................................................................................... 495 19.3 Writer Mode (H8/3577, H8/3567, H8/3567U).................................................................. 496 19.3.1 Writer Mode Setup............................................................................................... 496 19.3.2 Socket Adapter Pin Assignments and Memory Map ........................................... 497 19.4 PROM Programming ........................................................................................................ 502 19.4.1 Programming and Verification............................................................................. 502 19.4.2 Notes on Programming ........................................................................................ 507 19.4.3 Reliability of Programmed Data .......................................................................... 508 Section 20 Clock Pulse Generator .................................................................................. 20.1 Overview........................................................................................................................... 20.1.1 Block Diagram ..................................................................................................... 20.1.2 Register Configuration......................................................................................... 20.2 Register Descriptions ........................................................................................................ 20.2.1 Standby Control Register (SBYCR) .................................................................... 20.3 Oscillator........................................................................................................................... 20.3.1 Connecting a Crystal Resonator........................................................................... 20.3.2 External Clock Input ............................................................................................ 20.4 Duty Adjustment Circuit................................................................................................... 20.5 Medium-Speed Clock Divider .......................................................................................... 20.6 Bus Master Clock Selection Circuit .................................................................................. 20.7 Universal Clock Pulse Generator [H8/3567 Group Version with On-Chip USB] ........... 20.7.1 Block Diagram ..................................................................................................... 20.7.2 Registers............................................................................................................... 509 509 509 509 510 510 511 511 513 516 516 516 516 516 517 Section 21 Power-Down State ......................................................................................... 521 21.1 Overview........................................................................................................................... 21.1.1 Register Configuration......................................................................................... 21.2 Register Descriptions ........................................................................................................ 21.2.1 Standby Control Register (SBYCR) .................................................................... 21.2.2 Module Stop Control Register (MSTPCR) .......................................................... 21.3 Medium-Speed Mode........................................................................................................ 21.4 Sleep Mode ....................................................................................................................... 21.4.1 Sleep Mode .......................................................................................................... 21.4.2 Clearing Sleep Mode............................................................................................ 21.5 Module Stop Mode ........................................................................................................... 521 524 524 524 526 526 528 528 528 528 Rev. 3.00 Mar 17, 2006 page xxi of xxiv 21.5.1 Module Stop Mode .............................................................................................. 21.5.2 Usage Note........................................................................................................... 21.6 Software Standby Mode.................................................................................................... 21.6.1 Software Standby Mode....................................................................................... 21.6.2 Clearing Software Standby Mode ........................................................................ 21.6.3 Setting Oscillation Settling Time after Clearing Software Standby Mode .......... 21.6.4 Software Standby Mode Application Example.................................................... 21.6.5 Usage Note........................................................................................................... 21.7 Hardware Standby Mode .................................................................................................. 21.7.1 Hardware Standby Mode ..................................................................................... 21.7.2 Hardware Standby Mode Timing......................................................................... 528 529 530 530 530 531 531 532 533 533 534 Section 22 Electrical Characteristics.............................................................................. 535 22.1 Absolute Maximum Ratings ............................................................................................. 22.2 DC Characteristics ............................................................................................................ 22.3 AC Characteristics ............................................................................................................ 22.3.1 Clock Timing ....................................................................................................... 22.3.2 Control Signal Timing ......................................................................................... 22.3.3 Timing of On-Chip Supporting Modules............................................................. 22.4 A/D Conversion Characteristics........................................................................................ 22.5 USB Function Pin Characteristics..................................................................................... 22.6 Usage Notes ...................................................................................................................... 535 536 540 541 543 545 552 553 556 Appendix A CPU Instruction Set .................................................................................... 559 A.1 A.2 A.3 Instruction Set List ............................................................................................................ 559 Operation Code Map......................................................................................................... 567 Number of States Required for Execution ........................................................................ 569 Appendix B Internal I/O Registers ................................................................................. 575 B.1 B.2 B.3 Addresses .......................................................................................................................... 575 Register Selection Conditions ........................................................................................... 580 Functions........................................................................................................................... 586 Appendix C I/O Port Block Diagrams........................................................................... 673 C.1 C.2 C.3 C.4 C.5 C.6 C.7 Port 1 Block Diagrams...................................................................................................... Port 2 Block Diagrams...................................................................................................... Port 3 Block Diagram ....................................................................................................... Port 4 Block Diagrams...................................................................................................... Port 5 Block Diagrams...................................................................................................... Port 6 Block Diagrams...................................................................................................... Port 7 Block Diagram ....................................................................................................... Rev. 3.00 Mar 17, 2006 page xxii of xxiv 673 678 682 683 688 691 696 C.8 C.9 Port 8 Block Diagrams...................................................................................................... 697 Port D Block Diagram....................................................................................................... 699 Appendix D Pin States ....................................................................................................... 700 D.1 Port States in Each Mode .................................................................................................. 700 Appendix E Timing of Transition to and Recovery from Hardware Standby Mode................................................................. 701 E.1 E.2 Timing of Transition to Hardware Standby Mode ............................................................ 701 Timing of Recovery from Hardware Standby Mode......................................................... 701 Appendix F Product Code Lineup .................................................................................. 702 Appendix G Package Dimensions .................................................................................. 703 Rev. 3.00 Mar 17, 2006 page xxiii of xxiv Rev. 3.00 Mar 17, 2006 page xxiv of xxiv Section 1 Overview Section 1 Overview 1.1 Overview The H8/3577 Group and H8/3567 Group comprise single-chip microcomputers (MCUs) built around the H8/300 CPU and equipped with on-chip supporting functions required for system configuration. On-chip supporting functions required for system configuration include ROM and RAM, a 16-bit free-running timer (FRT), 8-bit timer (TMR), watchdog timer (WDT), two PWM timers (PWM 2 and PWMX), serial communication interface (SCI), I C bus interface (IIC), A/D converter (ADC), and I/O ports. The H8/3577 Group comprises 64-pin MCUs, and the H8/3567 Group 42-pin MCUs, but the H8/3567 Group also includes a 64-pin variation with on-chip universal serial bus (USB) hubs and function. The on-chip ROM is either PROM (ZTAT) or mask ROM, with a capacity of 56 or 32 kbytes. There is only one operating mode: single-chip mode. The features of the H8/3577 Group and H8/3567 Group are shown in table 1.1. Rev. 3.00 Mar 17, 2006 page 1 of 706 REJ09B0303-0300 Section 1 Overview Table 1.1 Features Item Specifications CPU • General-register architecture Sixteen 8-bit general registers (also usable as eight 16-bit registers) • High-speed operation suitable for realtime control Maximum operating frequency: 20 MHz/5 V (HD6433564-10: 10 MHz/5 V) High-speed arithmetic operations 8/16-bit register-register add/subtract: 0.1 µs (20-MHz operation) 8 × 8-bit register-register multiply: 0.7 µs (20-MHz operation) 16 ÷ 8-bit register-register divide: 0.7 µs (20-MHz operation) • Instruction set suitable for high-speed operation 2-byte or 4-byte instruction length Register-register basic operations Memory-register data transfer by MOV instruction • Instructions with special features Multiply instructions (8 bits × 8 bits) Divide instructions (16 bits ÷ 8 bits) Bit-accumulator instructions Bit position specifiable by means of register indirect specification 16-bit free-running timer (FRT), 1 channel 8-bit timer (TMR), 2 channels (TMR0, TMR1) • One 16-bit free-running counter (usable for external event counting) • Two output compare outputs • Four input capture inputs (with buffer operation capability) Each channel has: • One 8-bit up-counter (usable for external event counting) • Two timer constant registers • The two channels can be connected Rev. 3.00 Mar 17, 2006 page 2 of 706 REJ09B0303-0300 Section 1 Overview Item Specifications Timer connection and 8-bit timer (TMR), 2 channels (TMRX, TMRY) Input/output and FRT, TMR1, TMRX, TMRY can be interconnected • Measurement of input signal or frequency-divided waveform pulse width and cycle (FRT, TMR1) • Output of waveform obtained by modification of input signal edge (FRT, TMR1) • Determination of input signal duty cycle (TMRX) • Output of waveform synchronized with input signal (FRT, TMRX, TMRY) • Automatic generation of cyclical waveform (FRT, TMRY) Watchdog timer (WDT), 1 channel • Watchdog timer or interval timer function selectable 8-bit PWM timer (PWM) • Maximum of 16 (H8/3577 Group) or 8 (H8/3567 Group) outputs • Pulse duty cycle settable from 0 to 100% • Resolution: 1/256 • 1.25 MHz maximum carrier frequency (20-MHz operation) • Maximum of 2 outputs • Resolution: 1/16384 • 312.5 kHz maximum carrier frequency (20-MHz operation) Serial communication interface (SCI), 1 channel (SCI0) • Asynchronous mode or synchronous mode selectable • Multiprocessor communication function A/D converter • Resolution: 10 bits • Input: 8 channels (H8/3577 Group) 14-bit PWM timer (PWMX) 4 channels (H8/3567 Group) I/O ports • High-speed conversion : 6.7 µs minimum conversion time (20-MHz operation) • Single or scan mode selectable • Sample-and-hold function • A/D conversion can be activated by external trigger or timer trigger • Input/output pins: 43 (H8/3577 Group, H8/3567 Group models with onchip USB) or 27 (H8/3567 Group) • Input-only pins: 8 (H8/3577 Group) or 4 (H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 3 of 706 REJ09B0303-0300 Section 1 Overview Item Specifications Memory • PROM or mask ROM • High-speed static RAM Product Code ROM RAM H8/3577, H8/3567, H8/3567U 56 kbytes 2 kbytes H8/3574, H8/3564, H8/3564U 32 kbytes 2 kbytes • Four external interrupt pins (NMI, IRQ0 to IRQ2) • 26 internal interrupt sources (H8/3567U Group: 30 sources) • Medium-speed mode • Sleep mode • Module stop mode • Software standby mode • Hardware standby mode Clock pulse generator • Built-in duty correction circuit Packages • 64-pin plastic DIP (DP-64S) • 64-pin plastic QFP (FP-64A) • 42-pin plastic DIP (DP-42S) • 44-pin plastic QFP (FP-44A) • Conforms to Philips I C bus interface standard • Single master mode/slave mode • Arbitration lost condition can be identified • Supports two slave addresses Interrupt controller Power-down state 2 I C bus interface (IIC), 2 channels Universal serial • bus interface (USB) [H8/3567U, • H8/3564U] 2 Comprises five downstream hubs and one function (four sets of downstream pins) Three-endpoint monitor device class function EP0: For USB control EP1, EP2: For monitor control • Supports 12 Mbps high-speed transfer mode • Built-in 12 MHz clock pulse generator and 4X multiplication circuit • Built-in bus driver/receiver (requires 3.3 V analog power supply) Rev. 3.00 Mar 17, 2006 page 4 of 706 REJ09B0303-0300 Section 1 Overview Item Specifications Product lineup Product Code Group H8/3577 Mask ROM Version HD6433577 HD6433574 H8/3567 HD6433567 ZTAT Version HD6473577 — HD6473567 ROM/RAM (Bytes) Packages 56 k/2 k DP-64S, FP-64A 32 k/2 k 56 k/2 k DP-42S, FP-44A HD6433564-20 — 32 k/2 k HD6433564-10 — 32 k/2 k DP-42S 56 k/2 k DP-64S, FP-64A HD6433567U HD6433564U HD6473567U — 32 k/2 k Rev. 3.00 Mar 17, 2006 page 5 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 6 of 706 REJ09B0303-0300 Port 6 10-bit A/D converter IIC × 2 channels SCI × 1 channel 14-bit PWM Internal address bus 8-bit timer × 4 channels Timer connection (TMR0, TMR1, TMRX, TMRY) 16-bit FRT Port 1 AN7/ P77 AN6/ P76 AN5/ P75 AN4/ P74 AN3/ P73 AN2/ P72 AN1/ P71 AN0/ P70 Port 4 8-bit PWM WDT0 Internal data bus RAM ROM Port 2 HSYNCO/TMO1/ TMOX/P67 CSYNCI/TMRI1/ FTOB/P66 HSYNCI/TMCI1/ FTID/P65 CLAMPO/TMO0/ FTIC/P64 VFBACKI/TMRI0/ FTIB/P63 VSYNCI/ TMIY/FTIA/ P62 VSYNCO/FTOA/P61 HFBACKI/TMCI0/TMIX/ FTCI/P60 Clock pulse generator Interrupt controller Port 3 SDA0/ P47 φ/ P46 P45 P44 P43 IRQ0/ P42 IRQ1/ P41 ADTRG/ IRQ2/ P40 H8/300 CPU AVCC AVSS P52/ SCK0/ SCL0 P51/ RXD0 P50/ TXD0 P17/ PW7 P16/ PW6 P15/ PW5 P14/ PW4 P13/ PW3 P12/ PW2 P11/ PW1/ PWX1 P10/ PW0/ PWX0 P27/ PW15/ CBLANK P26/ PW14 P25/ PW13 P24/ PW12/ SCL1 P23/ PW11/ SDA1 P22/ PW10 P21/ PW9 P20/ PW8 P37 P36 P35 P34 P33 P32 P31 P30 1.2 MD1 MD0 EXTAL XTAL STBY RES NMI VCL, VCC VSS Section 1 Overview Internal Block Diagrams Figures 1.1 and 1.2 show internal block diagrams of the H8/3577 Group and H8/3567 Group. Port 5 Peripheral address bus Peripheral data bus Bus controller Port 7 Figure 1.1 Internal Block Diagram of H8/3577 Group Port 4 Port 6 10-bit A/D converter IIC × 2 channels Port 1 AN3/P73 AN2/P72 AN1/P71 AN0/P70 SCI × 1 channel 14-bit PWM Internal address bus 8-bit timer × 4 channels Timer connection (TMR0, TMR1, TMRX, TMRY) 16-bit FRT 8-bit PWM WDT0 Bus controller USB Port C RAM H8/300 CPU Internal data bus ROM Interrupt controller Clock pulse generator HSYNCO/TMO1/ TMOX/P67 CSYNCI/TMRI1/FTOB/P66 HSYNCI/TMCI1/FTID/P65 CLAMPO/TMO0/FTIC/P64 VFBACKI/TMRI0/FTIB/P63 VSYNCI/TMIY/FTIA/P62 VSYNCO/FTOA/P61 HFBACKI/TMCI0/TMIX/FTCI/P60 TEST EXTAL XTAL STBY RES NMI VCL, VCC VSS When on-chip USB is provided Port D SDA0/P47 φ/P46 P45 P44 P43 IRQ0/P42 IRQ1/P41 ADTRG/IRQ2/P40 DrVCC DrVSS EXTAL12 XTAL12 When on-chip USB is provided AVCC AVSS P52/SCK0/SCL0 P51/RXD0 P50/TXD0 P17/PW7/SCL1 P16/PW6/SDA1 P15/PW5/CBLANK P14/PW4 P13/PW3 P12/PW2 P11/PW1/PWX1 P10/PW0/PWX0 PC7/OCP5 PC6/OCP4 PC5/OCP3 PC4/OCP2 PC3/ENP5 PC2/ENP4 PC1/ENP3 PC0/ENP2 USD– USD+ PD7/DS5D– PD6/DS5D+ PD5/DS4D– PD4/DS4D+ PD3/DS3D– PD2/DS3D+ PD1/DS2D– PD0/DS2D+ Section 1 Overview Port 5 Peripheral address bus Peripheral data bus Port 7 Figure 1.2 Internal Block Diagram of H8/3567 Group Rev. 3.00 Mar 17, 2006 page 7 of 706 REJ09B0303-0300 Section 1 Overview 1.3 Pin Arrangement and Functions 1.3.1 Pin Arrangement The pin arrangements of the H8/3577 Group are shown in figures 1.3 and 1.4, and those of the H8/3567 Group in figures 1.5 to 1.8. ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 P43 P44 P45 φ/P46 SDA0/P47 TxD0/P50 RxD0/P51 SCL0/SCK0/P52 RES NMI VCC/VCL STBY VSS XTAL EXTAL MD1 MD0 AVSS AN0/P70 AN1/P71 AN2/P72 AN3/P73 AN4/P74 AN5/P75 AN6/P76 AN7/P77 AVCC HFBACKI/TMIX/TMCI0/FTCI/P60 VSYNCO/FTOA/P61 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P37 P36 P35 P34 P33 P32 P31 P30 P10/PW0/PWX0 P11/PW1/PWX1 P12/PW2 P13/PW3 P14/PW4 P15/PW5 P16/PW6 P17/PW7 VSS P20/PW8 P21/PW9 P22/PW10 P23/PW11/SDA1 P24/PW12/SCL1 P25/PW13 P26/PW14 P27/PW15/CBLANK VCC P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO P63/FTIB/TMRI0/VFBACKI P62/FTIA/TMIY/VSYNCI Figure 1.3 H8/3577 Group Pin Arrangement (DP-64S: Top View) Rev. 3.00 Mar 17, 2006 page 8 of 706 REJ09B0303-0300 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P10/PW0/PWX0 P11/PW1/PWX1 P12/PW2 P13/PW3 P14/PW4 P15/PW5 P16/PW6 P17/PW7 VSS P20/PW8 P21/PW9 P22/PW10 P23/PW11/SDA1 P24/PW12/SCL1 P25/PW13 P26/PW14 Section 1 Overview 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 P27/PW15/CBLANK VCC P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO P63/FTIB/TMRI0/VFBACKI P62/FTIA/TMIY/VSYNCI P61/FTOA/VSYNCO P60/FTCI/TMCI0/TMIX/HFBACKI AVCC P77/AN7 P76/AN6 P75/AN5 P74/AN4 P73/AN3 TxD0/P50 RxD0/P51 SCL0/SCK0/P52 RES NMI VCC/VCL STBY VSS XTAL EXTAL MD1 MD0 AVSS AN0/P70 AN1/P71 AN2/P72 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P30 P31 P32 P33 P34 P35 P36 P37 ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 P43 P44 P45 φ/P46 SDA0/P47 Figure 1.4 H8/3577 Group Pin Arrangement (FP-64A: Top View) Rev. 3.00 Mar 17, 2006 page 9 of 706 REJ09B0303-0300 Section 1 Overview ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 φ/P46 SDA0/P47 SCL0/SCK0/P52 RES NMI VCC VCC/VCL STBY XTAL EXTAL TEST VSS/AVSS AN0/P70 AN1/P71 AN2/P72 AN3/P73 AVCC HFBACKI/TMIX/TMCI0/FTCI/P60 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 P45 P44 P43 P51/RxD0 P50/TxD0 P10/PW0/PWX0 P11/PW1/PWX1 P12/PW2 P13/PW3 P14/PW4 VSS P15/PW5/CBLANK P16/PW6/SDA1 P17/PW7/SCL1 P61/FTOA/VSYNCO P62/FTIA/TMIY/VSYNCI P63/FTIB/TMRI0/VFBACKI P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO Figure 1.5 H8/3567 Group Pin Arrangement (No USB; DP-42S: Top View) Rev. 3.00 Mar 17, 2006 page 10 of 706 REJ09B0303-0300 33 32 31 30 29 28 27 26 25 24 23 P10/PW0/PWX0 P11/PW1/PWX1 P12/PW2 P13/PW3 P14/PW4 VSS P15/PW5/CBLANK P16/PW6/SDA1 P17/PW7/SCL1 P61/FTOA/VSYNCO P62/FTIA/TMIY/VSYNCI Section 1 Overview 34 35 36 37 38 39 40 41 42 43 44 22 21 20 19 18 17 16 15 14 13 12 P63/FTIB/TMRI0/VFBACKI P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO NC P60/FTCI/TMCI0/TMIX/HFBACKI AVCC P73/AN3 P72/AN2 P71/AN1 SCL0/SCK0/P52 RES NMI VCC VCC/VCL STBY XTAL EXTAL TEST VSS/AVSS AN0/P70 1 2 3 4 5 6 7 8 9 10 11 TxD0/P50 RxD0/P51 P43 P44 P45 NC ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 φ/P46 SDA0/P47 Figure 1.6 H8/3567 Group Pin Arrangement (No USB; FP-44A: Top View) Rev. 3.00 Mar 17, 2006 page 11 of 706 REJ09B0303-0300 Section 1 Overview ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 φ/P46 SDA0/P47 SCL0/SCK0/P52 RES NMI VCC VCL/VCC STBY XTAL EXTAL TEST VSS/AVSS AN0/P70 AN1/P71 AN2/P72 AN3/P73 AVCC DrVCC USD+ USD− PD0/DS2D+ PD1/DS2D− PD2/DS3D+ PD3/DS3D− PD4/DS4D+ PD5/DS4D− PD6/DS5D+ PD7/DS5D− DrVSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P45 P44 P43 P51/RxD0 P50/TxD0 P10/PW0/PWX0 P11/PW1/PWX1 P12/PW2 P13/PW3 P14/PW4 VSS P15/PW5/CBLANK P16/PW6/SDA1 P17/PW7/SCL1 P61/FTOA/VSYNCO P62/FTIA/TMIY/VSYNCI P63/FTIB/TMRI0/VFBACKI P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO P60/FTCI/TMCI0/TMIX/HFBACKI EXTAL12 XTAL12 PC7/OCP5 PC6/OCP4 PC5/OCP3 PC4/OCP2 PC3/ENP5 PC2/ENP4 PC1/ENP3 PC0/ENP2 Figure 1.7 H8/3567 Group Pin Arrangement (USB On-Chip; DP-64S: Top View) Rev. 3.00 Mar 17, 2006 page 12 of 706 REJ09B0303-0300 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P13/PW3 P14/PW4 VSS P15/PW5/CBLANK P16/PW6/SDA1 P17/PW7/SCL1 P61/FTOA/VSYNCO P62/FTIA/TMIY/VSYNCI P63/FTIB/TMRI0/VFBACKI P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO P60/FTCI/TMCI0/TMIX/HFBACKI EXTAL12 XTAL12 Section 1 Overview 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 PC7/OCP5 PC6/OCP4 PC5/OCP3 PC4/OCP2 PC3/ENP5 PC2/ENP4 PC1/ENP3 PC0/ENP2 DrVSS DS5D−/PD7 DS5D+/PD6 DS4D−/PD5 DS4D+/PD4 DS3D−/PD3 DS3D+/PD2 DS2D−/PD1 VCC VCL/VCC STBY XTAL EXTAL TEST VSS/AVSS AN0/P70 AN1/P71 AN2/P72 AN3/P73 AVCC DrVCC USD+ USD− PD0/DS2D+ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PW2/P12 PWX1/PW1/P11 PWX0/PW0/P10 TxD0/P50 RxD0/P51 P43 P44 P45 ADTRG/IRQ2/P40 IRQ1/P41 IRQ0/P42 φ/P46 SDA0/P47 SCL0/SCK0/P52 RES NMI Figure 1.8 H8/3567 Group Pin Arrangement (USB On-Chip; FP-64A: Top View) Rev. 3.00 Mar 17, 2006 page 13 of 706 REJ09B0303-0300 Section 1 Overview 1.3.2 List of Pin Functions H8/3577 Group pin functions are listed in table 1.2, and H8/3567 Group pin functions in tables 1.3 and 1.4. Table 1.2 List of H8/3577 Group Pin Functions Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 1 57 P40/IRQ2/ADTRG EA16 2 58 P41/IRQ1 EA15 3 59 P42/IRQ0 PGM 4 60 P43 NC 5 61 P44 NC 6 62 P45 NC 7 63 P46/φ NC 8 64 P47/SDA0 NC 9 1 P50/TxD0 NC 10 2 P51/RxD0 NC 11 3 P52/SCK0/SCL0 NC 12 4 RES VPP 13 5 NMI EA9 14 6 VCL, VCC (ZTAT) VCC 15 7 STBY VSS 16 8 VSS VSS 17 9 XTAL NC 18 10 EXTAL NC 19 11 MD1 VSS 20 12 MD0 VSS 21 13 AVSS VSS 22 14 P70/AN0 NC 23 15 P71/AN1 NC 24 16 P72/AN2 NC 25 17 P73/AN3 NC Rev. 3.00 Mar 17, 2006 page 14 of 706 REJ09B0303-0300 Section 1 Overview Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 26 18 P74/AN4 NC 27 19 P75/AN5 NC 28 20 P76/AN6 NC 29 21 P77/AN7 NC 30 22 AVCC VCC 31 23 P60/FTCI/TMCI0/HFBACKI/TMIX NC 32 24 P61/FTOA/VSYNCO NC 33 25 P62/FTIA/VSYNCI/TMIY NC 34 26 P63/FTIB/TMRI0/VFBACKI VCC 35 27 P64/FTIC/TMO0/CLAMPO VCC 36 28 P65/FTID/TMCI1/HSYNCI NC 37 29 P66/FTOB/TMRI1/CSYNCI NC 38 30 P67/TMO1/TMOX/HSYNCO NC 39 31 VCC VCC 40 32 P27/PW15/CBLANK CE 41 33 P26/PW14 EA14 42 34 P25/PW13 EA13 43 35 P24/PW12/SCL1 EA12 44 36 P23/PW11/SDA1 EA11 45 37 P22/PW10 EA10 46 38 P21/PW9 OE 47 39 P20/PW8 EA8 48 40 VSS VSS 49 41 P17/PW7 EA7 50 42 P16/PW6 EA6 51 43 P15/PW5 EA5 52 44 P14/PW4 EA4 53 45 P13/PW3 EA3 54 46 P12/PW2 EA2 55 47 P11/PW1/PWX1 EA1 Rev. 3.00 Mar 17, 2006 page 15 of 706 REJ09B0303-0300 Section 1 Overview Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 56 48 P10/PW0/PWX0 EA0 57 49 P30 EO0 58 50 P31 EO1 59 51 P32 EO2 60 52 P33 EO3 61 53 P34 EO4 62 54 P35 EO5 63 55 P36 EO6 64 56 P37 EO7 Rev. 3.00 Mar 17, 2006 page 16 of 706 REJ09B0303-0300 Section 1 Overview Table 1.3 List of H8/3567 Group Pin Functions (No USB) Pin No. Pin Name DP-42S FP-44A Single-Chip Mode PROM Writer Mode 1 40 P40/IRQ2/ADTRG EA16 2 41 P41/IRQ1 CE 3 42 P42/IRQ0 PGM 4 43 P46/φ EA11 5 44 P47/SDA0 VCC 6 1 P52/SCK0/SCL0 VCC 7 2 RES VPP 8 3 NMI EA9 9 4 VCC VCC 10 5 VCL, VCC (ZTAT) VCC 11 6 STBY VSS 12 7 XTAL NC 13 8 EXTAL NC 14 9 TEST VSS 15 10 AVSS/VSS VSS 16 11 P70/AN0 EA12 17 12 P71/AN1 EA13 18 13 P72/AN2 EA14 19 14 P73/AN3 EA15 20 15 AVCC VCC 21 16 P60/FTCI/TMCI0/HFBACKI/TMIX EO0 — 17 NC NC 22 18 P64/FTIC/TMO0/CLAMPO EO4 23 19 P65/FTID/TMCI1/HSYNCI EO5 24 20 P66/FTOB/TMRI1/CSYNCI EO6 25 21 P67/TMO1/TMOX/HSYNCO EO7 26 22 P63/FTIB/TMRI0/VFBACKI EO3 27 23 P62/FTIA/VSYNCI/TMIY EO2 28 24 P61/FTOA/VSYNCO EO1 Rev. 3.00 Mar 17, 2006 page 17 of 706 REJ09B0303-0300 Section 1 Overview Pin No. Pin Name DP-42S FP-44A Single-Chip Mode PROM Writer Mode 29 25 P17/PW7/SCL1 EA7 30 26 P16/PW6/SDA1 EA6 31 27 P15/PW5/CBLANK EA5 32 28 VSS VSS 33 29 P14/PW4 EA4 34 30 P13/PW3 EA3 35 31 P12/PW2 EA2 36 32 P11/PW1/PWX1 EA1 37 33 P10/PW0/PWX0 EA0 38 34 P50/TxD0 NC 39 35 P51/RxD0 NC 40 36 P43 EA8 41 37 P44 OE 42 38 P45 EA10 — 39 NC NC Rev. 3.00 Mar 17, 2006 page 18 of 706 REJ09B0303-0300 Section 1 Overview Table 1.4 List of H8/3567 Group Pin Functions (USB On-Chip) Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 1 57 P40/IRQ2/ADTRG EA16 2 58 P41/IRQ1 CE 3 59 P42/IRQ0 PGM 4 60 P46/φ EA11 5 61 P47/SDA0 VCC 6 62 P52/SCK0/SCL0 VCC 7 63 RES VPP 8 64 NMI EA9 9 1 VCC VCC 10 2 VCL, VCC (ZTAT) VCC 11 3 STBY VSS 12 4 XTAL NC 13 5 EXTAL NC 14 6 TEST VSS 15 7 AVSS/VSS VSS 16 8 P70/AN0 EA12 17 9 P71/AN1 EA13 18 10 P72/AN2 EA14 19 11 P73/AN3 EA15 20 12 AVCC VCC 21 13 DrVCC VCC 22 14 USD+ NC 23 15 USD– NC 24 16 PD0/DS2D+ NC 25 17 PD1/DS2D– NC 26 18 PD2/DS3D+ NC 27 19 PD3/DS3D– NC 28 20 PD4/DS4D+ NC 29 21 PD5/DS4D– NC Rev. 3.00 Mar 17, 2006 page 19 of 706 REJ09B0303-0300 Section 1 Overview Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 30 22 PD6/DS5D+ NC 31 23 PD7/DS5D– NC 32 24 DrVSS VSS 33 25 PC0/ENP2 NC 34 26 PC1/ENP3 NC 35 27 PC2/ENP4 NC 36 28 PC3/ENP5 NC 37 29 PC4/OCP2 NC 38 30 PC5/OCP3 NC 39 31 PC6/OCP4 NC 40 32 PC7/OCP5 NC 41 33 XTAL12 NC 42 34 EXTAL12 NC 43 35 P60/FTCI/TMCI0/HFBACKI/TMIX EO0 44 36 P64/FTIC/TMO0/CLAMPO EO4 45 37 P65/FTID/TMCI1/HSYNCI EO5 46 38 P66/FTOB/TMRI1/CSYNCI EO6 47 39 P67/TMO1/TMOX/HSYNCO EO7 48 40 P63/FTIB/TMRI0/VFBACKI EO3 49 41 P62/FTIA/VSYNCI/TMIY EO2 50 42 P61/FTOA/VSYNCO EO1 51 43 P17/PW7/SCL1 EA7 52 44 P16/PW6/SDA1 EA6 53 45 P15/PW5/CBLANK EA5 54 46 VSS VSS 55 47 P14/PW4 EA4 56 48 P13/PW3 EA3 57 49 P12/PW2 EA2 58 50 P11/PW1/PWX1 EA1 59 51 P10/PW0/PWX0 EA0 Rev. 3.00 Mar 17, 2006 page 20 of 706 REJ09B0303-0300 Section 1 Overview Pin No. Pin Name DP-64S FP-64A Single-Chip Mode PROM Writer Mode 60 52 P50/TxD0 NC 61 53 P51/RxD0 NC 62 54 P43 EA8 63 55 P44 OE 64 56 P45 EA10 Rev. 3.00 Mar 17, 2006 page 21 of 706 REJ09B0303-0300 Section 1 Overview 1.3.3 Pin Functions Table 1.5 summarizes the functions of the H8/3577 Group and H8/3567 Group pins. Table 1.5 Pin Functions Pin No. H8/3567 Group (No USB) H8/3577 Group H8/3567 Group (USB On-Chip) Type Symbol DP64S FP64A DP42S FP44A DP64S FP64A I/O Name and Function Power VCC 39 31 9 4 9 1 Input Power: For connection to the power supply (5 V). VCL/VCC 14 6 10 5 10 2 Input Internal step-up power: For connection to an external capacitor. In the ZTAT version, connect this pin to the power supply (5 V). Clock Operating mode control System control VSS 16, 48 8, 40 32 28 15, 54 7, 46 Input Ground: For connection to the power supply (0 V). Connect all VSS pins to the system power supply (0 V). XTAL 17 9 12 7 12 4 Input For connection of a crystal resonator or external clock input. EXTAL 18 10 13 8 13 5 Input For connection examples, see section 20, Clock Pulse Generator. φ 7 63 4 43 4 60 Output System clock: Supplies the system clock to external devices. — — — — Input Mode pins: These pins set the operating mode. Connect all three pins—MD1, MD0, and TEST—to the power supply (5 V). MD1 19 11 MD0 20 12 TEST — — 14 9 14 6 RES 12 4 7 2 7 63 Input Reset input: When this pin is driven low, the chip goes to the reset state. STBY 15 7 11 6 11 3 Input Standby: When this pin is driven low, a transition is made to hardware standby mode. Rev. 3.00 Mar 17, 2006 page 22 of 706 REJ09B0303-0300 Section 1 Overview Pin No. H8/3567 Group (No USB) H8/3577 Group H8/3567 Group (USB On-Chip) Type Symbol DP64S FP64A DP42S FP44A DP64S FP64A I/O Name and Function Interrupts NMI 13 5 8 3 8 64 Input Nonmaskable interrupt: Requests a nonmaskable interrupt. IRQ0 to IRQ2 3 to 1 59 to 57 3 to 1 42 to 40 3 to 1 59 to Input 57 Interrupt request 0 to 2: These pins request a maskable interrupt. 31 23 21 16 43 35 Input FRT counter clock input: Pin that inputs an external clock signal to the freerunning counter (FRC). FTOA 32 24 28 24 50 42 Output FRT output compare A output: The output compare A output pin. FTOB 37 29 24 20 46 38 Output FRT output compare B output: The output compare B output pin. FTIA 33 25 27 23 49 41 Input FRT input capture A input: The input capture A input pin. FTIB 34 26 26 22 48 40 Input FRT input capture B input: The input capture B input pin. FTIC 35 27 22 18 44 36 Input FRT input capture C input: The input capture C input pin. FTID 36 28 23 19 45 37 Input FRT input capture D input: The input capture D input pin. TMO0 35 27 22 18 44 36 Output TMO1 38 30 25 21 47 39 Compare-match output: Compare-match output pins for TMR0, TMR1, and TMRX. TMOX 38 30 25 21 47 39 Input Counter external clock input: Pins that input an external clock to the TMR0 and TMR1 counters. Input Counter external reset input: TMR0 and TMR1 counter reset input pins. 16-bit free- FTCI running timer (FRT) 8-bit timer (TMR0, TMR1, TMRX, TMRY) TMCI0 31 23 21 16 43 35 TMCI1 36 28 23 19 45 37 TMRI0 34 26 26 22 48 40 TMRI1 37 29 24 20 46 38 Rev. 3.00 Mar 17, 2006 page 23 of 706 REJ09B0303-0300 Section 1 Overview Pin No. H8/3567 Group (No USB) H8/3577 Group H8/3567 Group (USB On-Chip) Type Symbol DP64S FP64A DP42S FP44A DP64S FP64A I/O Name and Function 8-bit timer (TMR0, TMR1, TMRX, TMRY) TMIX 31 23 21 16 43 35 Input TMIY 33 25 27 23 49 41 Counter external clock input/reset input: Pins with a dual function of TMRX and TMRY counter clock input and reset input. Serial communication interface (SCI0) TxD0 9 1 38 34 60 52 Output Transmit data: Data output pins. RxD0 10 2 39 35 61 53 Input Receive data: Data input pins. SCK0 11 3 6 1 6 62 Input/ output Serial clock: Clock input/output pins. The SCK0 output type is NMOS push-pull. A/D converter AN7 to AN4 29 to 21 to 26 18 — — — — Input Analog 7 to 0: Analog input pins. AN3 to AN0 25 to 17 to 22 14 19 to 14 to 16 11 19 to 11 to Input 16 8 ADTRG 1 57 1 40 1 57 Input A/D conversion external trigger input: Pin for input of an external trigger to start A/D conversion. AVCC 30 22 20 15 20 12 Input Analog power: The A/D converter reference power supply pin. When the A/D converter is not used, connect this pin to the system power supply (+5 V). AVSS 21 13 15 Rev. 3.00 Mar 17, 2006 page 24 of 706 REJ09B0303-0300 10 15 7 Input Analog ground: The A/D converter ground pin. Connect this pin to the system power supply (0 V). Section 1 Overview Pin No. H8/3567 Group (No USB) H8/3577 Group Type Symbol DP64S PWM timer (PWM) PW15 to PW8 PW7 to PW0 14-bit PWM timer (PWMX) Timer connection 2 I C bus interface (IIC) FP64A H8/3567 Group (USB On-Chip) DP42S FP44A DP64S FP64A I/O Name and Function 40 to 32 to 47 39 — — — — Output PWM timer output: PWM timer pulse output pins. 49 to 41 to 56 48 29 to 25 to 31 27 51 to 43 to 53 45 33 to 29 to 37 33 55 to 47 to 59 51 Output PWMX timer output: PWM D/A pulse output pins. Input Timer connection input: Timer connection synchronization signal input pins. Output Timer connection output: Timer connection synchronization signal output pins. Input/ Output I2C clock input/output (channels 0 and 1): I2C clock input/output pins. PWX0 56 48 37 33 59 51 PWX1 55 47 36 32 58 50 VSYNCI 33 25 27 23 49 41 HSYNCI 36 28 23 19 45 37 CSYNCI 37 29 24 20 46 38 VFBACKI 34 26 26 22 48 40 HFBACKI 31 23 21 16 43 35 VSYNCO 32 24 28 24 50 42 HSYNCO 38 30 25 21 47 39 CLAMPO 35 27 22 18 44 36 CBLANK 40 32 31 27 53 45 SCL0 11 3 6 1 6 62 SCL1 43 35 29 25 51 43 These pins have a bus drive function. The SCL0 output type is NMOS open-drain. SDA0 8 64 5 44 5 61 SDA1 44 36 30 26 52 44 Input/ Output I2C data input/output (channels 0 and 1): I2C data input/output pins. These pins have a bus drive function. The SDA0 output type is NMOS open-drain. Rev. 3.00 Mar 17, 2006 page 25 of 706 REJ09B0303-0300 Section 1 Overview Pin No. H8/3577 Group H8/3567 Group (No USB) H8/3567 Group (USB On-Chip) Type Symbol DP64S FP64A DP42S FP44A DP64S FP64A Universal serial bus (USB) USD+ — — — — 22 14 23 15 USD– DS2D+ 24 16 DS2D– — — — — 25 17 DS3D+ 26 18 DS3D– 27 19 DS4D+ 28 20 DS4D– 29 21 DS5D+ 30 22 DS5D– 31 23 I/O Name and Function Input/ Output Upstream data input/output: USB upstream data input/ output pins. Input/ Output Upstream data input/output 2 to 5: USB hub downstream data input/output pins. ENP2 to ENP5 — — — — 33 to 25 to Output 36 28 Power supply control IC power output enable signal output: Output pins to USB port power supply control IC enable input OCP2 to OCP5 — — — — 37 to 29 to Input 40 32 Overcurrent detection signal input: Input pins for overcurrent detection signal from USB port power supply control IC XTAL12 — — — — 41 33 Input EXTAL12 — — — — 42 34 Input USB clock input: For connection of a 12 MHz crystal resonator or external clock input. Quadrupled to 48 MHz inside the chip. DrVCC — — — — 21 13 Input Bus driver power: For connection of the bus driver/receiver power supply (3.3 V). DrVSS — — — — 32 24 Input Bus driver ground: For connection of the bus driver/receiver power supply (0 V). Rev. 3.00 Mar 17, 2006 page 26 of 706 REJ09B0303-0300 Section 1 Overview Pin No. H8/3567 Group (No USB) H8/3577 Group Type Symbol DP64S FP64A I/O ports P17 to P10 49 to 41 to 56 48 DP42S FP44A H8/3567 Group (USB On-Chip) DP64S FP64A I/O 29 to 25 to 31 27 51 to 43 to Input/ 53 45 Output 33 to 29 to 37 33 55 to 47 to 59 51 Name and Function Port 1: Eight input/output pins. The direction of each pin can be selected in the port 1 data direction register (P1DDR). P27 to P20 40 to 32 to 47 39 — — — — Input/ Output Port 2: Eight input/output pins. The direction of each pin can be selected in the port 2 data direction register (P2DDR). P37 to P30 64 to 56 to 57 49 — — — — Input/ Output Port 3: Eight input/output pins. The direction of each pin can be selected in the port 3 data direction register (P3DDR). P47 to P40 8 to 1 5, 4 44, 43 5, 4 61, 60 Input/ 56 to Output Port 4: Eight input/output pins. The direction of each pin (except P46) can be selected in the port 4 data direction register (P4DDR). P47 is an NMOS push-pull output. P52 to P50 P67 to P60 64 to 57 11 to 3 to 9 1 38 to 30 to 31 23 38 to 42 to 36 40 42 to 3 to 40 1 64 to 54 62 59 to 3 to 57 1 6 1 6 62 39 35 61 53 38 34 60 52 Input/ Output Port 5: Three input/output pins. The direction of each pin can be selected in the port 5 data direction register (P5DDR). P52 is an NMOS push-pull output. 25 to 21 to 22 18 47 to 39 to Input/ 44 36 Output 26 to 22 to 28 24 48 to 40 to 50 42 Port 6: Eight input/output pins. The direction of each pin can be selected in the port 6 data direction register (P6DDR). 21 16 43 35 — — — P77 to P74 29 to 21 to 26 18 — P73 to P70 25 to 17 to 22 14 19 to 14 to 16 11 19 to 11 to 16 8 Input Port 7: Eight (H8/3577 Group) or four (H8/3567 Group) input pins. Rev. 3.00 Mar 17, 2006 page 27 of 706 REJ09B0303-0300 Section 1 Overview Pin No. H8/3577 Group H8/3567 Group (No USB) H8/3567 Group (USB On-Chip) DP64S FP64A DP42S FP44A DP64S PC7 to PC0 — — — — 40 to 32 to Input/ 33 25 Output Port C: Eight input/output pins. The direction of each pin can be selected in the port C data direction register (PCDDR). PD7 to PD0 — — — — 31 to 23 to Input/ 24 16 Output Port D: Eight input/output pins. The direction of each pin can be selected in the port D data direction register (PDDDR). These pins are driven by DrVCC (3.3 V). Type Symbol I/O ports Rev. 3.00 Mar 17, 2006 page 28 of 706 REJ09B0303-0300 FP64A I/O Name and Function Section 2 CPU Section 2 CPU 2.1 Overview The H8/300 CPU has sixteen 8-bit general registers, which can also be paired as eight 16-bit registers. Its concise instruction set is designed for high-speed operation. 2.1.1 Features Features of the H8/300 CPU are listed below. • General-register architecture Sixteen 8-bit general registers, also usable as eight 16-bit general registers • Instruction set with 55 basic instructions, including: Multiply and divide instructions Powerful bit-manipulation instructions • Eight addressing modes Register direct (Rn) Register indirect (@Rn) Register indirect with displacement (@(d:16, Rn)) Register indirect with post-increment or pre-decrement (@Rn+/@–Rn) Absolute address (@aa:8/@aa:16) Immediate (#xx:8/#xx:16) Program-counter relative (@(d:8, PC)) Memory indirect (@@aa:8) • 64-kbyte address space • High-speed operation All frequently used instructions are executed in two to four states High-speed arithmetic and logic operations 8- or 16-bit register-register add or subtract: 0.1 µs (operating at φ = 20 MHz) 8 × 8-bit multiply: 0.7 µs (operating at φ = 20 MHz) 16 ÷ 8-bit divide: 0.7 µs (operating at φ = 20 MHz) • Low-power operation modes SLEEP instruction for transfer to low-power operation Rev. 3.00 Mar 17, 2006 page 29 of 706 REJ09B0303-0300 Section 2 CPU 2.1.2 Address Space The H8/300 CPU supports an address space of up to 64 kbytes for storing program code and data. See section 3.3, Address Map, for details of the memory map. 2.1.3 Register Configuration Figure 2.1 shows the register structure of the H8/300 CPU. There are two groups of registers: the general registers and control registers. General registers (Rn) 7 0 7 0 R0H R0L R1H R1L R2H R2L R3H R3L R4H R4L R5H R5L R6H R6L R7H (SP) R7L Control registers (CR) 15 0 PC CCR 7 6 5 4 3 2 1 0 I UHUNZ VC Carry flag Overflow flag Zero flag Negative flag Legend: SP: Stack pointer PC: Program counter CCR: Condition code register Figure 2.1 CPU Registers Rev. 3.00 Mar 17, 2006 page 30 of 706 REJ09B0303-0300 Half-carry flag Interrupt mask bit User bit User bit Section 2 CPU 2.2 Register Descriptions 2.2.1 General Registers All the general registers can be used as both data registers and address registers. When used as data registers, they can be accessed as 16-bit registers (R0 to R7), or the high bytes (R0H to R7H) and low bytes (R0L to R7L) can be accessed separately as 8-bit registers. When used as address registers, the general registers are accessed as 16-bit registers (R0 to R7). R7 also functions as the stack pointer (SP), used implicitly by hardware in exception processing and subroutine calls. When it functions as the stack pointer, as indicated in figure 2.2, SP (R7) points to the top of the stack. Lower address side [H'0000] Unused area SP (R7) Stack area Upper address side [H'FFFF] Figure 2.2 Stack Pointer 2.2.2 Control Registers The CPU control registers include a 16-bit program counter (PC) and an 8-bit condition code register (CCR). Program Counter (PC) This 16-bit register indicates the address of the next instruction the CPU will execute. All instructions are fetched 16 bits (1 word) at a time, so the least significant bit of the PC is ignored (always regarded as 0). Rev. 3.00 Mar 17, 2006 page 31 of 706 REJ09B0303-0300 Section 2 CPU Condition Code Register (CCR) This 8-bit register contains internal status information, including the interrupt mask bit (I) and half-carry (H), negative (N), zero (Z), overflow (V), and carry (C) flags. These bits can be read and written by software (using the LDC, STC, ANDC, ORC, and XORC instructions). The N, Z, V, and C flags are used as branching conditions for conditional branching (Bcc) instructions. Bit 7—Interrupt Mask Bit (I): When this bit is set to 1, interrupts are masked. This bit is set to 1 automatically at the start of exception handling. The interrupt mask bit may be read and written by software. For further details, see section 5, Interrupt Controller. Bit 6—User Bit (U): Can be used freely by the user. Bit 5—Half-Carry Flag (H): When the ADD.B, ADDX.B, SUB.B, SUBX.B, CMP.B, or NEG.B instruction is executed, this flag is set to 1 if there is a carry or borrow at bit 3, and is cleared to 0 otherwise. The H flag is used implicitly by the DAA and DAS instructions. When the ADD.W, SUB.W, or CMP.W instruction is executed, the H flag is set to 1 if there is a carry or borrow at bit 11, and is cleared to 0 otherwise. Bit 4—User Bit (U): Can be used freely by the user. Bit 3—Negative Flag (N): Indicates the most significant bit (sign bit) of the result of an instruction. Bit 2—Zero Flag (Z): Set to 1 to indicate a zero result, and cleared to 0 to indicate a non-zero result. Bit 1—Overflow Flag (V): Set to 1 when an arithmetic overflow occurs, and cleared to 0 at other times. Bit 0—Carry Flag (C): Set to 1 when a carry occurs, and cleared to 0 otherwise. Used by: • Add instructions, to indicate a carry • Subtract instructions, to indicate a borrow • Shift/rotate carry The carry flag is also used as a bit accumulator by bit manipulation instructions. Some instructions leave some or all of the flag bits unchanged. Rev. 3.00 Mar 17, 2006 page 32 of 706 REJ09B0303-0300 Section 2 CPU Refer to the H8/300 Series Programming Manual for the action of each instruction on the flag bits. 2.2.3 Initial Register Values In reset exception handling, the program counter (PC) is initialized by a vector address (H'0000) load, and the I bit in the CCR is set to 1. The other CCR bits and the general registers are not initialized. In particular, the stack pointer (R7) is not initialized. The stack pointer should be initialized by software, by the first instruction executed after a reset. 2.3 Data Formats The H8/300 CPU can process 1-bit data, 4-bit (BCD) data, 8-bit (byte) data, and 16-bit (word) data. 1-bit data is handled by bit manipulation instructions, and is accessed by being specified as bit n (n = 0, 1, 2, ... 7) in the operand data (byte). Byte data is handled by all arithmetic and logic instructions except ADDS and SUBS. Word data is handled by the MOV.W, ADD.W, SUB.W, CMP.W, ADDS, SUBS, MULXU (8 bits × 8 bits), and DIVXU (16 bits ÷ 8 bits) instructions. With the DAA and DAS decimal adjustment instructions, byte data is handled as two 4-bit BCD data units. Rev. 3.00 Mar 17, 2006 page 33 of 706 REJ09B0303-0300 Section 2 CPU 2.3.1 Data Formats in General Registers Data of all the sizes above can be stored in general registers as shown in figure 2.3. Data Type Register No. Data Format 7 1-bit data RnH 7 0 6 5 4 3 2 1 0 don’t care 7 1-bit data RnL Byte data RnH Byte data RnL Word data Rn 4-bit BCD data RnH don’t care 7 7 0 MSB LSB don’t care 0 6 5 3 2 1 0 don’t care 7 0 MSB LSB 15 0 MSB LSB 7 4 3 Upper digit 0 Lower digit don’t care 7 4-bit BCD data 4 RnL don’t care 4 Upper digit Legend: RnH: Upper byte of general register RnL: Lower byte of general register MSB: Most significant bit LSB: Least significant bit Figure 2.3 General Register Data Formats Rev. 3.00 Mar 17, 2006 page 34 of 706 REJ09B0303-0300 0 3 Lower digit Section 2 CPU 2.3.2 Memory Data Formats Figure 2.4 indicates the data formats in memory. For access by the H8/300L CPU, word data stored in memory must always begin at an even address. When word data beginning at an odd address is accessed, the least significant bit is regarded as 0, and the word data beginning at the preceding address is accessed. The same applies to instruction codes. Data Type Address Data Format 7 1-bit data Address n 7 Byte data Address n MSB Even address MSB Word data Odd address Byte data (CCR) on stack Word data on stack 0 6 5 4 3 2 1 0 LSB Upper 8 bits Lower 8 bits LSB Even address MSB CCR LSB Odd address MSB CCR* LSB Even address MSB Odd address LSB Legend: CCR: Condition code register Note: * Ignored on return Figure 2.4 Memory Data Formats When the stack is accessed using R7 as an address register, word access should always be performed. The CCR is stored as word data with the same value in the upper 8 bits and the lower 8 bits. On return, the lower 8 bits are ignored. Rev. 3.00 Mar 17, 2006 page 35 of 706 REJ09B0303-0300 Section 2 CPU 2.4 Addressing Modes 2.4.1 Addressing Modes The H8/300 CPU supports the eight addressing modes listed in table 2.1. Each instruction uses a subset of these addressing modes. Table 2.1 Addressing Modes No. Address Modes Symbol 1 Register direct Rn 2 Register indirect @Rn 3 Register indirect with displacement @(d:16, Rn) 4 Register indirect with post-increment Register indirect with pre-decrement @Rn+ @–Rn 5 Absolute address @aa:8 or @aa:16 6 Immediate #xx:8 or #xx:16 7 Program-counter relative @(d:8, PC) 8 Memory indirect @@aa:8 1. Register Direct—Rn: The register field of the instruction specifies an 8- or 16-bit general register containing the operand. Only the MOV.W, ADD.W, SUB.W, CMP.W, ADDS, SUBS, MULXU (8 bits × 8 bits), and DIVXU (16 bits ÷ 8 bits) instructions have 16-bit operands. 2. Register Indirect—@Rn: The register field of the instruction specifies a 16-bit general register containing the address of the operand in memory. 3. Register Indirect with Displacement—@(d:16, Rn): The instruction has a second word (bytes 3 and 4) containing a displacement which is added to the contents of the specified general register to obtain the operand address in memory. This mode is used only in MOV instructions. For the MOV.W instruction, the resulting address must be even. Rev. 3.00 Mar 17, 2006 page 36 of 706 REJ09B0303-0300 Section 2 CPU 4. Register Indirect with Post-Increment or Pre-Decrement—@Rn+ or @–Rn: • Register indirect with post-increment—@Rn+ The @Rn+ mode is used with MOV instructions that load registers from memory. The register field of the instruction specifies a 16-bit general register containing the address of the operand. After the operand is accessed, the register is incremented by 1 for MOV.B or 2 for MOV.W, and the result of the addition is stored in the register. For MOV.W, the original contents of the 16-bit general register must be even. • Register indirect with pre-decrement—@–Rn The @–Rn mode is used with MOV instructions that store register contents to memory. The register field of the instruction specifies a 16-bit general register which is decremented by 1 or 2 to obtain the address of the operand in memory. The register retains the decremented value. The size of the decrement is 1 for MOV.B or 2 for MOV.W. For MOV.W, the original contents of the register must be even. 5. Absolute Address—@aa:8 or @aa:16: The instruction specifies the absolute address of the operand in memory. The absolute address may be 8 bits long (@aa:8) or 16 bits long (@aa:16). The MOV.B and bit manipulation instructions can use 8-bit absolute addresses. The MOV.B, MOV.W, JMP, and JSR instructions can use 16-bit absolute addresses. For an 8-bit absolute address, the upper 8 bits are assumed to be 1 (H'FF). The address range is H'FF00 to H'FFFF (65280 to 65535). 6. Immediate—#xx:8 or #xx:16: The second byte (#xx:8) or the third and fourth bytes (#xx:16) of the instruction code are used directly as the operand. Only MOV.W instructions can be used with #xx:16. The ADDS and SUBS instructions implicitly contain the value 1 or 2 as immediate data. Some bit manipulation instructions contain 3-bit immediate data in the second or fourth byte of the instruction, specifying a bit number. 7. Program-Counter Relative—@(d:8, PC): This mode is used in the Bcc and BSR instructions. An 8-bit displacement in byte 2 of the instruction code is sign-extended to 16 bits and added to the program counter contents to generate a branch destination address, and the PC contents to be added are the start address of the next instruction, so that the possible branching range is –126 to +128 bytes (–63 to +64 words) from the branch instruction. The displacement should be an even number. Rev. 3.00 Mar 17, 2006 page 37 of 706 REJ09B0303-0300 Section 2 CPU 8. Memory Indirect—@@aa:8: This mode can be used by the JMP and JSR instructions. The second byte of the instruction code specifies an 8-bit absolute address. This specifies an operand in memory, and a branch is performed with the contents of this operand as the branch address. The upper 8 bits of the absolute address are assumed to be 0 (H'00), so the address range is from H'0000 to H'00FF (0 to 255). Note that with the H8/300 Series, the lower end of the address area is also used as a vector area. See section 4, Exception Handling, for details on the vector area. If an odd address is specified as a branch destination or as the operand address of a MOV.W instruction, the least significant bit is regarded as 0, causing word access to be performed at the address preceding the specified address. See 2.3.2, Memory Data Formats, for further information. 2.4.2 Effective Address Calculation Table 2.2 shows how effective addresses are calculated in each of the addressing modes. Arithmetic and logic instructions use register direct addressing (1). The ADD.B, ADDX, SUBX, CMP.B, AND, OR, and XOR instructions can also use immediate addressing (6). Data transfer instructions can use all addressing modes except program-counter relative (7) and memory indirect (8). Bit manipulation instructions use register direct (1), register indirect (2), or 8-bit absolute addressing (5) to specify a byte operand, and 3-bit immediate addressing (6) to specify a bit position in that byte. The BSET, BCLR, BNOT, and BTST instructions can also use register direct addressing (1) to specify the bit position. Rev. 3.00 Mar 17, 2006 page 38 of 706 REJ09B0303-0300 Section 2 CPU Table 2.2 No. 1 Effective Address Calculation Addressing Mode and Instruction Format Effective Address Calculation Method Effective Address (EA) 3 Register direct, Rn 0 rm 15 87 op 2 43 rm rn 3 76 43 15 0 15 0 15 0 15 0 15 0 0 rm Register indirect with displacement, @(d:16, Rn) 15 rn Operand is contents of registers indicated by rm/rn Contents (16 bits) of register indicated by rm op 0 0 Register indirect, @Rn 15 3 76 op 43 15 0 Contents (16 bits) of register indicated by rm 0 rm disp disp 4 Register indirect with post-increment, @Rn+ 15 76 op 43 15 0 Contents (16 bits) of register indicated by rm 0 rm 1 or 2 Register indirect with pre-decrement, @–Rn 15 76 op 43 rm 15 0 Contents (16 bits) of register indicated by rm 0 Incremented or decremented by 1 if operand is byte size, 1 or 2 and by 2 if word size Rev. 3.00 Mar 17, 2006 page 39 of 706 REJ09B0303-0300 Section 2 CPU No. 5 Addressing Mode and Instruction Format Effective Address Calculation Method Effective Address (EA) Absolute address @aa:8 15 87 op 15 87 0 H'FF 0 abs @aa:16 15 15 0 0 op abs 6 Immediate #xx:8 15 Operand is 1- or 2-byte immediate data 87 op 0 IMM #xx:16 15 0 op IMM 7 Program-counter relative @(d:8, PC) 87 15 op 15 0 disp Rev. 3.00 Mar 17, 2006 page 40 of 706 REJ09B0303-0300 0 PC contents 15 Sign extension disp 0 Section 2 CPU No. Addressing Mode and Instruction Format 8 Memory indirect, @@aa:8 15 87 op Effective Address Calculation Method Effective Address (EA) 0 abs 15 87 H'00 0 abs 15 0 Memory contents (16 bits) Legend: rm, rn: Register field op: Operation field disp: Displacement IMM: Immediate data abs: Absolute address Rev. 3.00 Mar 17, 2006 page 41 of 706 REJ09B0303-0300 Section 2 CPU 2.5 Instruction Set The H8/300 Series can use a total of 55 instructions, which are grouped by function in table 2.3. Table 2.3 Instruction Set Function Instructions Number Data transfer MOV, PUSH* , POP* Arithmetic operations ADD, SUB, ADDX, SUBX, INC, DEC, ADDS, SUBS, DAA, DAS, MULXU, DIVXU, CMP, NEG 14 Logic operations AND, OR, XOR, NOT 4 Shift SHAL, SHAR, SHLL, SHLR, ROTL, ROTR, ROTXL, ROTXR 8 Bit manipulation 14 Branch BSET, BCLR, BNOT, BTST, BAND, BIAND, BOR, BIOR, BXOR, BIXOR, BLD, BILD, BST, BIST 2 Bcc* , JMP, BSR, JSR, RTS System control RTE, SLEEP, LDC, STC, ANDC, ORC, XORC, NOP 8 Block data transfer (Cannot be used in the H8/3577 Group and H8/3567 Group) EEPMOV 1 1 1 1 5 Total: 55 Notes: 1. PUSH Rn is equivalent to MOV.W Rn, @–SP. POP Rn is equivalent to MOV.W @SP+, Rn. The same applies to machine language. 2. Bcc is a conditional branch instruction. Rev. 3.00 Mar 17, 2006 page 42 of 706 REJ09B0303-0300 Section 2 CPU Tables 2.4 to 2.11 show the function of each instruction. The notation used is defined next. Notation Rd General register (destination) Rs General register (source) Rn General register (EAd), <Ead> Destination operand (EAs), <Eas> Source operand CCR Condition code register N N (negative) flag of CCR Z Z (zero) flag of CCR V V (overflow) flag of CCR C C (carry) flag of CCR PC Program counter SP Stack pointer #IMM Immediate data disp Displacement + Addition – Subtraction × Multiplication ÷ Division ∧ AND logical ∨ OR logical ⊕ Exclusive OR logical → Move ~ Logical negation (logical complement) :3 3-bit length :8 8-bit length :16 16-bit length ( ), < > Contents of operand indicated by effective address Rev. 3.00 Mar 17, 2006 page 43 of 706 REJ09B0303-0300 Section 2 CPU 2.5.1 Data Transfer Instructions Table 2.4 describes the data transfer instructions. Figure 2.5 shows their object code formats. Table 2.4 Data Transfer Instructions Instruction Size* Function MOV B/W (EAs) → Rd, Rs → (EAd) Moves data between two general registers or between a general register and memory, or moves immediate data to a general register. The Rn, @Rn, @(d:16, Rn), @aa:16, #xx:16, @–Rn, and @Rn+ addressing modes are available for word data. The @aa:8 addressing mode is available for byte data only. The @–R7 and @R7+ modes require a word-size specification. POP W @SP+ → Rn Pops a general register from the stack. Equivalent to MOV.W @SP+, Rn. PUSH W Rn → @–SP Pushes general register onto the stack. Equivalent to MOV.W Rn, @–SP. Notes: * Size: Operand size B: Byte W: Word Rev. 3.00 Mar 17, 2006 page 44 of 706 REJ09B0303-0300 Section 2 CPU 15 8 7 0 op rm 15 8 rn 0 rm 8 Rm→Rn 7 op 15 MOV rn @Rm←→Rn 7 0 op rm rn @(d:16, Rm)←→Rn disp 15 8 7 0 op rm 15 8 op 7 0 rn 15 @Rm+→Rn, or Rn →@–Rm rn abs 8 @aa:8←→Rn 7 0 op rn @aa:16←→Rn abs 15 8 op 7 0 rn 15 IMM 8 #xx:8→Rn 7 0 op rn #xx:16→Rn IMM 15 8 op 7 0 1 1 1 rn PUSH, POP @SP+ → Rn, or Rn → @–SP Legend: op: Operation field rm, rn: Register field disp: Displacement abs: Absolute address IMM: Immediate data Figure 2.5 Data Transfer Instruction Codes Rev. 3.00 Mar 17, 2006 page 45 of 706 REJ09B0303-0300 Section 2 CPU 2.5.2 Arithmetic Operations Table 2.5 describes the arithmetic instructions. Table 2.5 Arithmetic Instructions Instruction Size* Function ADD B/W Rd ± Rs → Rd, Rd + #IMM → Rd SUB ADDX Performs addition or subtraction on data in two general registers, or addition on immediate data and data in a general register. Immediate data cannot be subtracted from data in a general register. Word data can be added or subtracted only when both words are in general registers. B SUBX INC Performs addition or subtraction with carry on data in two general registers, or addition or subtraction with carry on immediate data and data in a general register. B DEC ADDS Rd ± 1 → Rd, Rd ± 2 → Rd Adds or subtracts 1 or 2 to or from a general register B DAS MULXU Rd ± 1 → Rd Increments or decrements a general register W SUBS DAA Rd ± Rs ± C → Rd, Rd ± #IMM ± C → Rd Rd decimal adjust → Rd Decimal-adjusts (adjusts to packed BCD) an addition or subtraction result in a general register by referring to the CCR B Rd × Rs → Rd Performs 8-bit × 8-bit unsigned multiplication on data in two general registers, providing a 16-bit result DIVXU B Rd ÷ Rs → Rd Performs 16-bit ÷ 8-bit unsigned division on data in two general registers, providing an 8-bit quotient and 8-bit remainder CMP B/W Rd – Rs, Rd – #IMM Compares data in a general register with data in another general register or with immediate data, and indicates the result in the CCR. Word data can be compared only between two general registers. NEG B 0 – Rd → Rd Obtains the two’s complement (arithmetic complement) of data in a general register Notes: * Size: Operand size B: Byte W: Word Rev. 3.00 Mar 17, 2006 page 46 of 706 REJ09B0303-0300 Section 2 CPU 2.5.3 Logic Operations Table 2.6 describes the four instructions that perform logic operations. Table 2.6 Logic Operation Instructions Instruction Size* Function AND B Rd ∧ Rs → Rd, Rd ∧ #IMM → Rd Performs a logical AND operation on a general register and another general register or immediate data OR B Rd ∨ Rs → Rd, Rd ∨ #IMM → Rd Performs a logical OR operation on a general register and another general register or immediate data XOR B Rd ⊕ Rs → Rd, Rd ⊕ #IMM → Rd Performs a logical exclusive OR operation on a general register and another general register or immediate data NOT B ~ Rd → Rd Obtains the one’s complement (logical complement) of general register contents Notes: * 2.5.4 Size: Operand size B: Byte Shift Operations Table 2.7 describes the eight shift instructions. Table 2.7 Shift Instructions Instruction Size* Function SHAL B Rd shift → Rd SHAR SHLL Performs an arithmetic shift operation on general register contents B SHLR ROTL Performs a logical shift operation on general register contents B ROTR ROTXL ROTXR Notes: * Rd shift → Rd Rd rotate → Rd Rotates general register contents B Rd rotate → Rd Rotates general register contents through the C (carry) bit Size: Operand size B: Byte Rev. 3.00 Mar 17, 2006 page 47 of 706 REJ09B0303-0300 Section 2 CPU Figure 2.6 shows the instruction code format of arithmetic, logic, and shift instructions. 15 8 7 op 0 rm 15 8 7 0 op 15 7 op 0 rm 8 op 0 0 rm 8 rn 7 rn 15 ADD, ADDX, SUBX, CMP (#XX:8) 7 op 15 MULXU, DIVXU IMM 8 op rn 7 rn 15 ADDS, SUBS, INC, DEC, DAA, DAS, NEG, NOT rn 8 15 ADD, SUB, CMP, ADDX, SUBX (Rm) rn AND, OR, XOR (Rm) 0 IMM 8 AND, OR, XOR (#xx:8) 7 op 0 rn SHAL, SHAR, SHLL, SHLR, ROTL, ROTR, ROTXL, ROTXR Legend: op: Operation field rm, rn: Register field IMM: Immediate data Figure 2.6 Arithmetic, Logic, and Shift Instruction Codes Rev. 3.00 Mar 17, 2006 page 48 of 706 REJ09B0303-0300 Section 2 CPU 2.5.5 Bit Manipulations Table 2.8 describes the bit-manipulation instructions. Figure 2.7 shows their object code formats. Table 2.8 Bit-Manipulation Instructions Instruction Size* Function BSET B 1 → (<bit-No.> of <EAd>) Sets a specified bit in a general register or memory to 1. The bit number is specified by 3-bit immediate data or the lower three bits of a general register. BCLR B 0 → (<bit-No.> of <EAd>) Clears a specified bit in a general register or memory to 0. The bit number is specified by 3-bit immediate data or the lower three bits of a general register. BNOT B ~ (<bit-No.> of <EAd>) → (<bit-No.> of <EAd>) Inverts a specified bit in a general register or memory. The bit number is specified by 3-bit immediate data or the lower three bits of a general register. BTST B ~ (<bit-No.> of <EAd>) → Z Tests a specified bit in a general register or memory and sets or clears the Z flag accordingly. The bit number is specified by 3-bit immediate data or the lower three bits of a general register. BAND B C ∧ (<bit-No.> of <EAd>) → C ANDs the C flag with a specified bit in a general register or memory, and stores the result in the C flag. BIAND B C ∧ [~ (<bit-No.> of <EAd>)] → C ANDs the C flag with the inverse of a specified bit in a general register or memory, and stores the result in the C flag. The bit number is specified by 3-bit immediate data. BOR B C ∨ (<bit-No.> of <EAd>) → C ORs the C flag with a specified bit in a general register or memory, and stores the result in the C flag. BIOR B C ∨ [~ (<bit-No.> of <EAd>)] → C ORs the C flag with the inverse of a specified bit in a general register or memory, and stores the result in the C flag. The bit number is specified by 3-bit immediate data. Notes: * Size: Operand size B: Byte Rev. 3.00 Mar 17, 2006 page 49 of 706 REJ09B0303-0300 Section 2 CPU Instruction Size* Function BXOR B C ⊕ (<bit-No.> of <EAd>) → C XORs the C flag with a specified bit in a general register or memory, and stores the result in the C flag. BIXOR B C ⊕ [~(<bit-No.> of <EAd>)] → C XORs the C flag with the inverse of a specified bit in a general register or memory, and stores the result in the C flag. The bit number is specified by 3-bit immediate data. BLD B (<bit-No.> of <EAd>) → C Copies a specified bit in a general register or memory to the C flag. BILD B ~ (<bit-No.> of <EAd>) → C Copies the inverse of a specified bit in a general register or memory to the C flag. The bit number is specified by 3-bit immediate data. BST B C → (<bit-No.> of <EAd>) BIST B ~ C → (<bit-No.> of <EAd>) Copies the C flag to a specified bit in a general register or memory. Copies the inverse of the C flag to a specified bit in a general register or memory. The bit number is specified by 3-bit immediate data. Notes: * Size: Operand size B: Byte Certain precautions are required in bit manipulation. See 2.8.1, Notes on Bit Manipulation, for details. Rev. 3.00 Mar 17, 2006 page 50 of 706 REJ09B0303-0300 Section 2 CPU BSET, BCLR, BNOT, BTST 15 8 7 op 0 IMM 15 8 7 op 0 rm 15 8 Operand: register direct (Rn) Bit No.: immediate (#xx:3) rn Operand: register direct (Rn) Bit No.: register direct (Rm) rn 7 0 rn 0 0 0 0 Operand: register indirect (@Rn) IMM 0 0 0 0 Bit No.: op rn 0 0 0 0 Operand: register indirect (@Rn) op rm 0 0 0 0 Bit No.: op op 15 8 15 8 7 0 7 abs IMM 15 8 0 Operand: absolute (@aa:8) 0 0 7 0 Bit No.: immediate (#xx:3) 0 op abs op register direct (Rm) 0 op op immediate (#xx:3) rm 0 Operand: absolute (@aa:8) 0 0 0 Bit No.: register direct (Rm) BAND, BOR, BXOR, BLD, BST 15 8 7 op 0 IMM 15 8 7 op op 15 8 Operand: register direct (Rn) Bit No.: immediate (#xx:3) rn 0 rn 0 0 0 0 Operand: register indirect (@Rn) IMM 0 0 0 0 Bit No.: 7 0 op abs op immediate (#xx:3) IMM 0 Operand: absolute (@aa:8) 0 0 0 Bit No.: immediate (#xx:3) Legend: op: Operation field rm, rn: Register field abs: Absolute address IMM: Immediate data Figure 2.7 Bit Manipulation Instruction Codes Rev. 3.00 Mar 17, 2006 page 51 of 706 REJ09B0303-0300 Section 2 CPU BIAND, BIOR, BIXOR, BILD, BIST 15 8 7 op 0 IMM 15 8 7 op op 15 8 Operand: register direct (Rn) Bit No.: immediate (#xx:3) rn 0 rn 0 0 0 0 Operand: register indirect (@Rn) IMM 0 0 0 0 Bit No.: 7 0 op abs op immediate (#xx:3) IMM 0 Operand: absolute (@aa:8) 0 0 0 Bit No.: immediate (#xx:3) Legend: op: Operation field rm, rn: Register field abs: Absolute address IMM: Immediate data Figure 2.7 Bit Manipulation Instruction Codes (cont) Rev. 3.00 Mar 17, 2006 page 52 of 706 REJ09B0303-0300 Section 2 CPU 2.5.6 Branching Instructions Table 2.9 describes the branching instructions. Figure 2.8 shows their object code formats. Table 2.9 Branching Instructions Instruction Size Function Bcc — Branches to the designated address if condition cc is true. The branching conditions are given below. Mnemonic Description Condition BRA (BT) Always (true) Always BRN (BF) Never (false) Never BHI High C∨Z=0 BLS Low or same C∨Z=1 BCC (BHS) Carry clear (high or same) C=0 BCS (BLO) Carry set (low) C=1 BNE Not equal Z=0 BEQ Equal Z=1 BVC Overflow clear V=0 BVS Overflow set V=1 BPL Plus N=0 BMI Minus N=1 BGE Greater or equal N⊕V=0 BLT Less than N⊕V=1 BGT Greater than Z ∨ (N ⊕ V) = 0 BLE Less or equal Z ∨ (N ⊕ V) = 1 JMP — Branches unconditionally to a specified address BSR — Branches to a subroutine at a specified address JSR — Branches to a subroutine at a specified address RTS — Returns from a subroutine Rev. 3.00 Mar 17, 2006 page 53 of 706 REJ09B0303-0300 Section 2 CPU 15 8 op 7 0 cc 15 disp 8 7 op 0 rm 15 Bcc 8 0 0 0 7 0 JMP (@Rm) 0 op JMP (@aa:16) abs 15 8 7 0 op abs 15 8 JMP (@@aa:8) 7 0 op disp 15 8 7 op 0 rm 15 BSR 8 0 0 0 7 0 JSR (@Rm) 0 op JSR (@aa:16) abs 15 8 7 op 0 abs 15 8 7 op Legend: op: Operation field cc: Condition field rm: Register field disp: Displacement abs: Absolute address Figure 2.8 Branching Instruction Codes Rev. 3.00 Mar 17, 2006 page 54 of 706 REJ09B0303-0300 JSR (@@aa:8) 0 RTS Section 2 CPU 2.5.7 System Control Instructions Table 2.10 describes the system control instructions. Figure 2.9 shows their object code formats. Table 2.10 System Control Instructions Instruction Size* Function RTE — Returns from an exception-handling routine SLEEP — Causes a transition from active mode to a power-down mode. See section 21, Power-Down State, for details. LDC B Rs → CCR, #IMM → CCR Moves immediate data or general register contents to the condition code register STC B CCR → Rd ANDC B CCR ∧ #IMM → CCR Copies the condition code register to a specified general register Logically ANDs the condition code register with immediate data ORC B CCR ∨ #IMM → CCR Logically ORs the condition code register with immediate data XORC B CCR ⊕ #IMM → CCR Logically exclusive-ORs the condition code register with immediate data NOP — PC + 2 → PC Only increments the program counter Notes: * Size: Operand size B: Byte Rev. 3.00 Mar 17, 2006 page 55 of 706 REJ09B0303-0300 Section 2 CPU 15 8 7 0 op 15 8 RTE, SLEEP, NOP 7 0 op 15 rn 8 7 op LDC, STC (Rn) 0 IMM Legend: op: Operation field rn: Register field IMM: Immediate data Figure 2.9 System Control Instruction Codes Rev. 3.00 Mar 17, 2006 page 56 of 706 REJ09B0303-0300 ANDC, ORC, XORC, LDC (#xx:8) Section 2 CPU 2.5.8 Block Data Transfer Instruction Table 2.11 describes the block data transfer instruction. Figure 2.10 shows its object code format. Table 2.11 Block Data Transfer Instruction Instruction Size Function EEPMOV (Cannot be used in the H8/3577 Group and H8/3567 Group) — If R4L ≠ 0 then repeat @R5+ → @R6+ R4L – 1 → R4L until R4L = 0 else next; Block transfer instruction. Transfers the number of data bytes specified by R4L from locations starting at the address indicated by R5 to locations starting at the address indicated by R6. After the transfer, the next instruction is executed. Certain precautions are required in using the EEPMOV instruction. See 2.8.2, Notes on Use of the EEPMOV Instruction, for details. 15 8 7 0 op op Legend: op: Operation field Figure 2.10 Block Data Transfer Instruction Code Rev. 3.00 Mar 17, 2006 page 57 of 706 REJ09B0303-0300 Section 2 CPU 2.6 Basic Operational Timing CPU operation is synchronized by a system clock (φ). The period from a rising edge of φ to the next rising edge is called one state. A bus cycle consists of two states or three states. The cycle differs depending on whether access is to on-chip memory or to on-chip peripheral modules. 2.6.1 Access to On-Chip Memory (RAM, ROM) Access to on-chip memory takes place in two states. The data bus width is 16 bits, allowing access in byte or word size. Figure 2.11 shows the on-chip memory access cycle. Bus cycle T1 state T2 state φ or φSUB Internal address bus Address Internal read signal Internal data bus (read access) Read data Internal write signal Internal data bus (write access) Write data Figure 2.11 On-Chip Memory Access Cycle Rev. 3.00 Mar 17, 2006 page 58 of 706 REJ09B0303-0300 Section 2 CPU 2.6.2 Access to On-Chip Peripheral Modules On-chip peripheral modules are accessed in three states. The data bus width is either 8 or 16 bits, so access in both byte and word size is supported. There are two categories of on-chip peripheral modules: 8-bit and 16-bit. To access word data from an 8-bit module, two instructions must be used. The upper byte is accessed first, followed by the lower byte. Accessing word data from a 16-bit module requires only one instruction. There are two types of registers: byte and word. The word register refers to registers were, as with a 16-bit counter, attempting to access the two bytes separately will cause problems. For word registers containing 8-bit modules, a circuit with a temporary register is available to allow normal access to the upper byte first, followed by the lower byte. Note that word registers containing only 16-bit modules do not have such a circuit. Therefore, only word access may be used with such registers. Figure 2.12 shows the access timing for on-chip peripheral modules. Bus cycle T1 state T2 state T3 state φ Internal address bus Address Internal read signal Internal data bus (read access) Read data Internal write signal Internal data bus (write access) Write data Figure 2.12 On-Chip Peripheral Module Access Cycle Rev. 3.00 Mar 17, 2006 page 59 of 706 REJ09B0303-0300 Section 2 CPU 2.7 CPU States 2.7.1 Overview There are four CPU states: the reset state, program execution state, program halt state, and exception-handling state. The program execution state includes active (high-speed or mediumspeed) mode. In the program halt state there are a sleep (high-speed or medium-speed) mode and standby mode. These states are shown in figure 2.13. Figure 2.14 shows the state transitions. CPU state Reset state The CPU is initialized Program execution state Active (high speed) mode The CPU executes successive program instructions at high speed, synchronized by the system clock Active (medium speed) mode The CPU executes successive program instructions at reduced speed, synchronized by the system clock Program halt state A state in which some or all of the chip functions are stopped to conserve power Sleep (high-speed) mode Low-power modes Sleep (medium-speed) mode Standby mode Exceptionhandling state A transient state in which the CPU changes the processing flow due to a reset or an interrupt Note: See section 21, Power-Down Modes, for details on the modes and their transitions. Figure 2.13 CPU Operation States Rev. 3.00 Mar 17, 2006 page 60 of 706 REJ09B0303-0300 Section 2 CPU Reset cleared Reset state Exception-handling state Reset occurs Reset occurs Reset occurs Interrupt source Program halt state Exception- Exceptionhandling handling request complete Program execution state SLEEP instruction executed Figure 2.14 State Transitions 2.7.2 Reset State The CPU is initialized in the reset state. 2.7.3 Program Execution State In the program execution state the CPU executes program instructions in sequence. There are two active modes (high-speed and medium-speed) when the CPU is in the program execution state. 2.7.4 Program Halt State In the program halt state there are three modes: two sleep modes (high speed and medium speed) and standby mode. See section 21, Power-Down Modes for details on these modes. 2.7.5 Exception-Handling State The exception-handling state is a transient state occurring when exception handling is started by a reset or interrupt and the CPU changes its normal processing flow. In exception handling caused by an interrupt, SP (R7) is referenced and the PC and CCR values are saved on the stack. For details on interrupt handling, see section 4, Exception Handling. Rev. 3.00 Mar 17, 2006 page 61 of 706 REJ09B0303-0300 Section 2 CPU 2.8 Application Notes 2.8.1 Notes on Bit Manipulation The BSET, BCLR, BNOT, BST, and BIST instructions read one byte of data, modify the data, then write the data byte again. Special care is required when using these instructions in cases where two registers are assigned to the same address, in the case of registers that include writeonly bits, and when the instruction accesses an I/O port. Order of Operation Operation 1 Read Read byte data at the designated address 2 Modify Modify a designated bit in the read data 3 Write Write the altered byte data to the designated address As in the examples above, P17 and P16 are input pins, with a low-level signal input at P17 and a high-level signal at P16. The remaining pins, P15 to P10, are output pins that output low-level signals. In this example, the BCLR instruction is used to change pin P10 to an input port. [A: Prior to executing BCLR] P17 P16 P15 P14 P13 P12 P11 P10 Input/output Input Input Output Output Output Output Output Output Pin state Low level High level Low level Low level Low level Low level Low level Low level DDR 0 0 1 1 1 1 1 1 DR 1 0 0 0 0 0 0 0 [B: BCLR instruction executed] BCLR #0 , P1DDR The BCLR instruction is executed designating DDR. Rev. 3.00 Mar 17, 2006 page 62 of 706 REJ09B0303-0300 Section 2 CPU [C: After executing BCLR] P17 P16 P15 P14 P13 P12 P11 P10 Input/output Output Output Output Output Output Output Output Input Pin state Low level High level Low level Low level Low level Low level Low level Low level DDR 1 1 1 1 1 1 1 0 DR 1 0 0 0 0 0 0 0 [D: Explanation of how BCLR operates] When the BCLR instruction is executed, first the CPU reads P1DDR. Since P1DDR is a writeonly register, the CPU reads an undefined value. In this example, the DDR value is H'FF, but the data read by the CPU is undefined; it is taken to be H'FF. Next, the CPU clears bit 0 in the read data to 0, changing the data to H'FE. Finally, this value (H'FE) is written to DDR and BCLR instruction execution ends. As a result of this operation, bit 0 in DDR becomes 0, making P10 an input port. However, bits 7 and 6 in DDR change to 1, so that P17 and P16 change from input pins to output pins. Rev. 3.00 Mar 17, 2006 page 63 of 706 REJ09B0303-0300 Section 2 CPU 2.8.2 Notes on Use of the EEPMOV Instruction (Cannot Be Used in the H8/3577 Group and H8/3567 Group) • The EEPMOV instruction is a block data transfer instruction. It moves the number of bytes specified by R4L from the address specified by R5 to the address specified by R6. R5 → ← R6 R5 + R4L → ← R6 + R4L • When setting R4L and R6, make sure that the final destination address (R6 + R4L) does not exceed H'FFFF. The value in R6 must not change from H'FFFF to H'0000 during execution of the instruction. R5 → R5 + R4L → ← R6 H'FFFF Not allowed Rev. 3.00 Mar 17, 2006 page 64 of 706 REJ09B0303-0300 ← R6 + R4L Section 3 MCU Operating Modes Section 3 MCU Operating Modes 3.1 Overview 3.1.1 Operating Mode Selection The H8/3577 Group and H8/3567 Group operate in the single-chip mode. The operating mode is specified by the setting of the mode pins (MD1 to MD0 or TEST). Table 3.1 lists the MCU operating modes. Table 3.1 MCU Operating Mode Selection • H8/3577 Group MCU Operating Mode MD1 MD0 Description Mode 0 0 0 — Mode 1 0 1 — Mode 2 1 0 — Mode 3 1 1 Single-chip mode • H8/3567 Group MCU Operating Mode TEST Description Mode 0 0 — Mode 3 1 Single-chip mode The H8/3577 Group and H8/3567 Group support the use of mode 3 only. Therefore, the mode pins must be set for mode 3 as indicated above. 3.1.2 Register Configuration The H8/3577 Group and H8/3567 Group have a mode control register (MDCR) that indicates the inputs at the mode pins (MD1 and MD0 or TEST), a system control register (SYSCR) that controls the operation of the MCU, and a serial timer control register (STCR) that controls the operation of the supporting modules. Table 3.2 summarizes these registers. Rev. 3.00 Mar 17, 2006 page 65 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes Table 3.2 MCU Registers Name Abbreviation R/W Initial Value Address* Mode control register MDCR R H'03 H'FFC5 System control register SYSCR R/W H'09 H'FFC4 Serial timer control register STCR R/W H'00 H'FFC3 Note: Lower 16 bits of the address. * 3.2 Register Descriptions 3.2.1 Mode Control Register (MDCR) Bit 7 6 5 4 3 2 1 0 — — — — — Initial value EXPE 0* 0 0 0 0 0 MDS1 1* MDS0 1* Read/Write R — — — — — R R Note: * Determined by pins MD1 and MD0 or TEST pin. MDCR is an 8-bit read-only register that indicates the operating mode setting and the current operating mode of the MCU. Bit 7—Expanded Mode Enable (EXPE): This bit should not be set to 1. Bits 6 to 2—Reserved: These bits cannot be modified and are always read as 0. Bits 1 and 0—Mode Select 1 and 0 (MDS1, MDS0): These bits indicate the input levels at pins MD1, MD0, and TEST (the current operating mode). Bits MDS1 and MDS0 correspond to MD1 and MD0 (H8/3577 Group). Alternately, bits MDS1 and MDS0 both correspond to the TEST pin (H8/3567 Group). MDS1 and MDS0 are read-only bits—they cannot be written to. The mode pin (MD1, MD0, and TEST) input levels are latched into these bits when MDCR is read. Rev. 3.00 Mar 17, 2006 page 66 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes 3.2.2 System Control Register (SYSCR) Bit 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W SYSCR is a readable/writable register that performs selection of system pin functions, reset source monitoring, interrupt control mode selection, NMI detected edge selection, supporting module register access control, and RAM address space control. Only bits 7, 6, 3, 1, and 0 are described here. For a detailed description of these bits, refer also to the description of the relevant modules (watchdog timer, RAM, etc.). For information on bits 5, 4, and 2, see section 5.2.1, System Control Register (SYSCR). SYSCR is initialized to H'09 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bit 7—Chip Select 2 Enable (CS2E): This bit should not be set to 1. Bit 6—IOS Enable (IOSE): This bit should not be set to 1. Bit 3—External Reset (XRST): Indicates the reset source. When the watchdog timer is used, a reset can be generated by watchdog timer overflow as well as by external reset input. XRST is a read-only bit. It is set to 1 by an external reset and cleared to 0 by watchdog timer overflow. Bit 3 XRST Description 0 A reset is generated by watchdog timer overflow 1 A reset is generated by an external reset (Initial value) Bit 1—Host Interface Enable (HIE): Enables or disables CPU access to on-chip supporting function registers. This bit controls CPU access to the 8-bit timer (channel X and Y) data registers and control registers (TCRX/TCRY, TCSRX/TCSRY, TICRR/TCORAY, TICRF/TCORBY, TCNTX/TCNTY, TCORC/TISR, TCORAX, and TCORBX), and the timer connection control registers (TCONRI, TCONRO, TCONRS, and SEDGR). Rev. 3.00 Mar 17, 2006 page 67 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes Bit 1 HIE Description 0 In areas H'FFF0 to H'FFF7 and H'FFFC to H'FFFF, CPU access to 8-bit timer (channels X and Y) data registers and control registers, and timer connection control registers, is permitted (Initial value) 1 In areas H'FFF0 to H'FFF7 and H'FFFC to H'FFFF, CPU access to 8-bit timer (channels X and Y) data registers and control registers, and timer connection control registers, is not permitted Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is initialized when the reset state is released. It is not initialized in software standby mode. Bit 0 RAME Description 0 On-chip RAM is disabled 1 On-chip RAM is enabled 3.2.3 (Initial value) Serial Timer Control Register (STCR) Bit 7 6 5 4 3 2 1 0 — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W STCR is an 8-bit readable/writable register that controls register access, the IIC operating mode, selects the TCNT input clock and controls USB. For details of functions other than register access control, see the descriptions of the relevant modules. If a module controlled by STCR is not used, do not write 1 to the corresponding bit. STCR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—Reserved: Do not write 1 to this bit. 2 2 Bits 6 and 5—I C Control (IICX1, IICX0): These bits control the operation of the I C bus 2 interface. For details, see section 16, I C Bus Interface. 2 2 Bit 4—I C Master Enable (IICE): Controls CPU access to the I C bus interface data registers and control registers (ICCR, ICSR, ICDR/SARX, and ICMR/SAR), the PWMX data registers and Rev. 3.00 Mar 17, 2006 page 68 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes control registers (DADRAH/DACR, DADRAL, DADRBH/DACNTH, and DADRBL/DACNTL), and the SCI control registers (SMR, BRR, and SCMR). Bit 4 IICE Description 0 Addresses H'FFD8 and H'FFD9, and H'FFDE and H'FFDF, are used for SCI0 control register access (Initial value) 1 Addresses H'FF88 and H'FF89, and H'FF8E and H'FF8F, are used for IIC1 data register and control register access Addresses H'FFA0 and H'FFA1, and H'FFA6 and H'FFA7, are used for PWMX data register and control register access Addresses H'FFD8 and H'FFD9, and H'FFDE and H'FFDF, are used for IIC0 data register and control register access Bit 3—Reserved: Do not write 1 to this bit. Bit 2—USB enable (USBE): This bit controls CPU access to the USB data register and control register. Bit 2 USBE Description 0 Prohibition of the above register access 1 Permission of the above register access (Initial value) Bits 1 and 0—Internal Clock Source Select 1 and 0 (ICKS1, ICKS0): These bits, together with bits CKS2 to CKS0 in TCR, select the clock to be input to TCNT. For details, see section 12, 8-Bit Timers. 3.3 Address Map Address maps are shown in figure 3.1 and figure 3.2. The on-chip ROM capacity is 56 kbytes (H8/3577, H8/3567, H8/3567U) or 32 kbytes (H8/3574, H8/3564, H8/3564U). Do not try access to reserved areas and the addresses where no memory and no I/O register exists. Rev. 3.00 Mar 17, 2006 page 69 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes H'0000 On-chip ROM H'DFFF H'E080 Reserved area H'E880 On-chip RAM H'EFFF H'F000 Reserved area H'F7FF H'F800 H'FE4F H'FE50 H'FEFF H'FF00 H'FF7F H'FF80 H'FFFF Internal I/O register 3 (H8/3567U only) Internal I/O register 2 On-chip RAM (128 bytes) Internal I/O register 1 Figure 3.1 H8/3577, H8/3567, and H8/3567U Address Map Rev. 3.00 Mar 17, 2006 page 70 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes H'0000 On-chip ROM H'7FFF Reserved area H'DFFF H'E080 Reserved area H'E880 H'EFFF H'F000 On-chip RAM Reserved area H'F7FF H'F800 Internal I/O register 3 (H8/3564U only) H'FE4F H'FE50 H'FEFF H'FF00 H'FF7F H'FF80 H'FFFF Internal I/O register 2 On-chip RAM (128 bytes) Internal I/O register 1 Figure 3.2 H8/3574, H8/3564, and H8/3564U Address Map Rev. 3.00 Mar 17, 2006 page 71 of 706 REJ09B0303-0300 Section 3 MCU Operating Modes Rev. 3.00 Mar 17, 2006 page 72 of 706 REJ09B0303-0300 Section 4 Exception Handling Section 4 Exception Handling 4.1 Overview 4.1.1 Exception Handling Types and Priority As table 4.1 indicates, exception handling may be caused by a reset, or interrupt. Exception handling is prioritized as shown in table 4.1. If two or more exceptions occur simultaneously, they are accepted and processed in order of priority. Table 4.1 Exception Types and Priority Priority Exception Type Start of Exception Handling High Reset Starts immediately after a low-to-high transition at the RES pin, or when the watchdog timer overflows. Interrupt Starts when execution of the current instruction or exception handling ends, if an interrupt request has been issued.* Low Note: 4.1.2 * Interrupt detection is not performed on completion of ANDC, ORC, XORC, or LDC instruction execution, or on completion of reset exception handling. Exception Handling Operation Exceptions originate from various sources. Trap instructions and interrupts are handled as follows: 1. The program counter (PC) and condition-code register (CCR) are pushed onto the stack. 2. The interrupt mask bits are updated. 3. A vector address corresponding to the exception source is generated, and program execution starts from that address. For a reset exception, steps 2 and 3 above are carried out. Rev. 3.00 Mar 17, 2006 page 73 of 706 REJ09B0303-0300 Section 4 Exception Handling 4.1.3 Exception Sources and Vector Table The exception sources are classified as shown in figure 4.1. Different vector addresses are assigned to different exception sources. Table 4.2 lists the exception sources and their vector addresses. Reset Exception sources External interrupts: NMI, IRQ2 to IRQ0 Interrupts Internal interrupts: interrupt sources in on-chip supporting modules Figure 4.1 Exception Sources Table 4.2 Exception Vector Table Exception Source Vector Number Vector Address* Reset 0 H'0000 to H'0001 Reserved for system use 1 H'0002 to H'0003 2 H'0004 to H'0005 3 H'0006 to H'0007 NMI 4 H'0008 to H'0009 IRQ0 5 H'000A to H'000B IRQ1 6 H'000C to H'000D External interrupt IRQ2 Reserved Internal interrupt* Note: * 7 H'000E to H'000F 8 H'0010 to H'0011 9 H'0012 to H'0013 10 H'0014 to H'0015 11 H'0016 to H'0017 12 H'0018 to H'0019 13 53 H'001A to H'001B H'006A to H'006B For details on internal interrupt vectors, see section 5.3.3, Interrupt Exception Vector Table. Rev. 3.00 Mar 17, 2006 page 74 of 706 REJ09B0303-0300 Section 4 Exception Handling 4.2 Reset 4.2.1 Overview A reset has the highest exception priority. When the RES pin goes low, all processing halts and the MCU enters the reset state. A reset initializes the internal state of the CPU and the registers of on-chip supporting modules. Reset exception handling begins when the RES pin changes from low to high. MCUs can also be reset by overflow of the watchdog timer. For details, see section 14, Watchdog Timer. 4.2.2 Reset Sequence The MCU enters the reset state when the RES pin goes low. To ensure that the chip is reset, hold the RES pin low for at least 20 ms when powering on. To reset the chip during operation, hold the RES pin low for at least 20 states. For pin states in a reset, see Appendix D.1, Port States in Each Processing State. When the RES pin goes high after being held low for the necessary time, the chip starts reset exception handling as follows: 1. The internal state of the CPU and the registers of the on-chip supporting modules are initialized, and the I bit is set to 1 in CCR. 2. The reset exception vector address is read and transferred to the PC, and program execution starts from the address indicated by the PC. Figure 4.2 shows an example of the reset sequence. Rev. 3.00 Mar 17, 2006 page 75 of 706 REJ09B0303-0300 Section 4 Exception Handling Vector Internal Fetch of first program fetch processing instruction φ RES Internal address bus (1) (3) Internal read signal Internal write signal High Internal data bus (1) (2) (3) (4) (2) (4) Reset exception vector address ((1) = H'0000) Start address (contents of reset exception vector address) Start address ((3) = (2)) First program instruction Figure 4.2 Reset Sequence 4.2.3 Interrupts after Reset If an interrupt is accepted after a reset but before the stack pointer (SP) is initialized, the PC and CCR will not be saved correctly, leading to a program crash. To prevent this, all interrupt requests, including NMI, are disabled immediately after a reset. Since the first instruction of a program is always executed immediately after the reset state ends, make sure that this instruction initializes the stack pointer (example: MOV.W #xx:16, SP). Rev. 3.00 Mar 17, 2006 page 76 of 706 REJ09B0303-0300 Section 4 Exception Handling 4.3 Interrupts Interrupt exception handling can be requested by four external sources (NMI and IRQ2 to IRQ0), and internal sources in the on-chip supporting modules. Figure 4.3 shows the interrupt sources and the number of interrupts of each type. The on-chip supporting modules that can request interrupts include the watchdog timer (WDT), 16-bit free-running timer (FRT), 8-bit timer (TMR), serial communication interface (SCI), A/D 2 converter (ADC), I C bus interface (IIC). Each interrupt source has a separate vector address. NMI is the highest-priority interrupt. Interrupts are controlled by the interrupt controller. For details on interrupts, see section 5, Interrupt Controller. External interrupts Interrupts Internal interrupts NMI (1) IRQ2 to IRQ0 (3) WDT* (1) FRT (7) TMR (10) SCI (4) ADC (1) IIC (3) USB (4) Notes: Numbers in parentheses are the numbers of interrupt sources. * When the watchdog timer is used as an interval timer, it generates an interrupt request at each counter overflow. Figure 4.3 Interrupt Sources and Number of Interrupts Rev. 3.00 Mar 17, 2006 page 77 of 706 REJ09B0303-0300 Section 4 Exception Handling 4.4 Stack Status after Exception Handling Figure 4.4 shows the stack after completion of interrupt exception handling. SP CCR CCR* PC (16 bits) Interrupt control mode 0 Note: * Ignored on return. Figure 4.4 Stack Status after Exception Handling Rev. 3.00 Mar 17, 2006 page 78 of 706 REJ09B0303-0300 Section 4 Exception Handling 4.5 Note on Stack Handling In word access, the least significant bit of the address is always assumed to be 0. The stack is always accessed by word access. Care should be taken to keep an even value in the stack pointer (general register R7). Use the PUSH and POP (or MOV.W Rn, @–SP and MOV.W @SP+, Rn) instructions to push and pop registers on the stack. Setting the stack pointer to an odd value can cause programs to crash. Figure 4.5 shows an example of damage caused when the stack pointer contains an odd address. PCH SP PCL SP R1L H'FECC PCL H'FECD H'FECF SP BSR instruction H'FECF set in SP PCH: PCL: R1L: SP: MOV.B R1L, @–R7 PC is improperly stored beyond top of stack PCH is lost Upper byte of program counter Lower byte of program counter General register Stack pointer Figure 4.5 Example of Damage Caused by Setting an Odd Address in R7 Rev. 3.00 Mar 17, 2006 page 79 of 706 REJ09B0303-0300 Section 4 Exception Handling Rev. 3.00 Mar 17, 2006 page 80 of 706 REJ09B0303-0300 Section 5 Interrupt Controller Section 5 Interrupt Controller 5.1 Overview 5.1.1 Features The MCUs control interrupts by means of an interrupt controller. The interrupt controller has the following features: • Independent vector addresses All interrupt sources are assigned independent vector addresses, making it unnecessary for the source to be identified in the interrupt handling routine. • Four external interrupt pins NMI is the highest-priority interrupt, and is accepted at all times. A rising or falling edge at the NMI pin can be selected for the NMI interrupt. Falling edge, rising edge, or both edge detection, or level sensing, at pins IRQ2 to IRQ0 can be selected for interrupts IRQ2 to IRQ0. Rev. 3.00 Mar 17, 2006 page 81 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.1.2 Block Diagram A block diagram of the interrupt controller is shown in figure 5.1. CPU SYSCR NMIEG NMI input NMI input unit IRQ input IRQ input unit ISR ISCR IER Interrupt request Vector number Priority determination I Internal interrupt requests WOVI to IICI1 USB-related interrupts Interrupt controller Legend: ISCR: IER: ISR: SYSCR: IRQ sense control register IRQ enable register IRQ status register System control register Figure 5.1 Block Diagram of Interrupt Controller Rev. 3.00 Mar 17, 2006 page 82 of 706 REJ09B0303-0300 CCR Section 5 Interrupt Controller 5.1.3 Pin Configuration Table 5.1 summarizes the pins of the interrupt controller. Table 5.1 Interrupt Controller Pins Name Symbol I/O Function Nonmaskable interrupt NMI Input Nonmaskable external interrupt; rising or falling edge can be selected External interrupt requests 2 to 0 IRQ2 to IRQ0 Input Maskable external interrupts; rising, falling, or both edges, or level sensing, can be selected 5.1.4 Register Configuration Table 5.2 summarizes the registers of the interrupt controller. Table 5.2 Interrupt Controller Registers Name Abbreviation R/W Initial Value Address System control register SYSCR R/W H'09 H'FFC4 IRQ sense control register H ISCRH R/W H'00 H'FEEC IRQ sense control register L ISCRL R/W H'00 H'FEED IRQ enable register IER R/W H'F8 H'FFC2 IRQ status register ISR R/(W)* H'00 H'FEEB Note: * Only 0 can be written, for flag clearing. Rev. 3.00 Mar 17, 2006 page 83 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.2 Register Descriptions 5.2.1 System Control Register (SYSCR) Bit 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W SYSCR is an 8-bit readable/writable register, bit 2 of which selects the detected edge for NMI. Only bits 5, 4, and 2 are described here; for details on the other bits, see section 3.2.2, System Control Register (SYSCR). SYSCR is initialized to H'09 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 5 and 4—Interrupt Control Mode 1 and 0 (INTM1, INTM0): The INTM1 and 0 bits must not be set to 1. Bit 5 Bit 4 INTM1 INTM0 Interrupt Control Mode Description 0 0 0 Interrupts are controlled by I bit 1 1 Cannot be used in H8/3577 Group and H8/3567 Group 0 2 Cannot be used in H8/3577 Group and H8/3567 Group 1 3 Cannot be used in H8/3577 Group and H8/3567 Group 1 (Initial value) Bit 2—NMI Edge Select (NMIEG): Selects the input edge for the NMI pin. Bit 2 NMIEG Description 0 Interrupt request generated at falling edge of NMI input 1 Interrupt request generated at rising edge of NMI input Rev. 3.00 Mar 17, 2006 page 84 of 706 REJ09B0303-0300 (Initial value) Section 5 Interrupt Controller 5.2.2 IRQ Enable Register (IER) Bit 7 6 5 4 3 2 1 0 — — — — — IRQ2E IRQ1E IRQ0E Initial value 1 1 1 1 1 0 0 0 Read/Write R R R R R R/W R/W R/W IER is a register that controls enabling and disabling of interrupt requests IRQ2 to IRQ0. IER is initialized to H'F8 by a reset and in hardware standby mode. Bits 7 to 3—Reserved: These bits cannot be modified and are always read as 1. Bits 2 to 0—IRQ2 to IRQ0 Enable (IRQ2E to IRQ0E): These bits select whether IRQ2 to IRQ0 are enabled or disabled. Bit n IRQnE Description 0 IRQn interrupt disabled 1 IRQn interrupt enabled (Initial value) Note: n = 2 to 0 Rev. 3.00 Mar 17, 2006 page 85 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.2.3 IRQ Sense Control Registers H and L (ISCRH, ISCRL) • ISCRH Bit 15 14 13 12 11 10 9 8 — — — — — — — — Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 5 4 3 2 1 0 • ISCRL Bit 7 6 — — Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W IRQ2SCB IRQ2SCA IRQ1SCB IRQ1SCA IRQ0SCB IRQ0SCA ISCRH and ISCRL are 8-bit readable/writable registers that select rising edge, falling edge, or both edge detection, or level sensing, for the input at pins IRQ2 to IRQ0. Each of the ISCR registers is initialized to H'00 by a reset and in hardware standby mode. ISCRH Bits 7 to 0, ISCRL Bits 7 and 6—Reserved: Do not write 1 to this bit. ISCRL Bits 5 to 0—IRQ2 Sense Control A and B (IRQ2SCA, IRQ2SCB) to IRQ0 Sense Control A and B (IRQ0SCA, IRQ0SCB) ISCRL Bits 5 to 0 IRQ2SCB to IRQ0SCB IRQ2SCA to IRQ0SCA 0 0 Interrupt request generated at IRQ2 to IRQ0 input low level (Initial value) 1 Interrupt request generated at falling edge of IRQ2 to IRQ0 input 0 Interrupt request generated at rising edge of IRQ2 to IRQ0 input 1 Interrupt request generated at both falling and rising edges of IRQ2 to IRQ0 input 1 Description Rev. 3.00 Mar 17, 2006 page 86 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.2.4 IRQ Status Register (ISR) Bit Initial value Read/Write Note: 7 6 5 4 3 2 1 0 — — — — — IRQ2F IRQ1F IRQ0F 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R R R R Only 0 can be written, to clear the flag. * ISR is an 8-bit readable/writable register that indicates the status of IRQ2 to IRQ0 interrupt requests. ISR is initialized to H'00 by a reset and in hardware standby mode. Bits 7 to 3—Reserved Bits 2 to 0—IRQ2 to IRQ0 Flags (IRQ2F to IRQ0F): These bits indicate the status of IRQ2 to IRQ0 interrupt requests. Bit n IRQnF 0 1 Description [Clearing conditions] (Initial value) • Cleared by reading IRQnF when set to 1, then writing 0 in IRQnF • When interrupt exception handling is executed when low-level detection is set (IRQnSCB = IRQnSCA = 0) and IRQn input is high • When IRQn interrupt exception handling is executed when falling, rising, or bothedge detection is set (IRQnSCB = 1 or IRQnSCA = 1) [Setting conditions] • When IRQn input goes low when low-level detection is set (IRQnSCB = IRQnSCA = 0) • When a falling edge occurs in IRQn input when falling edge detection is set (IRQnSCB = 0, IRQnSCA = 1) • When a rising edge occurs in IRQn input when rising edge detection is set (IRQnSCB = 1, IRQnSCA = 0) • When a falling or rising edge occurs in IRQn input when both-edge detection is set (IRQnSCB = IRQnSCA = 1) Note: n = 2 to 0 Rev. 3.00 Mar 17, 2006 page 87 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.3 Interrupt Sources Interrupt sources comprise external interrupts (NMI and IRQ2 to IRQ0) and internal interrupts. 5.3.1 External Interrupts There are four external interrupt sources: NMI, and IRQ2 to IRQ0. NMI, and IRQ2 to IRQ0 can be used to restore the H8/3577 Group and H8/3567 Group chip from software standby mode. NMI Interrupt: NMI is the highest-priority interrupt, and is always accepted by the CPU regardless of the interrupt control mode and the status of the CPU interrupt mask bits. The NMIEG bit in SYSCR can be used to select whether an interrupt is requested at a rising edge or a falling edge on the NMI pin. The vector number for NMI interrupt exception handling is 4. IRQ2 to IRQ0 Interrupts: Interrupts IRQ2 to IRQ0 are requested by an input signal at pins IRQ2 to IRQ0. Interrupts IRQ2 to IRQ0 have the following features: • Using ISCR, it is possible to select whether an interrupt is generated by a low level, falling edge, rising edge, or both edges, at pins IRQ2 to IRQ0. • Enabling or disabling of interrupt requests IRQ2 to IRQ0 can be selected with IER. • The status of interrupt requests IRQ2 to IRQ0 is indicated in ISR. ISR flags can be cleared to 0 by software. A block diagram of interrupts IRQ2 to IRQ0 is shown in figure 5.2. IRQnE IRQnSCA, IRQnSCB IRQnF Edge/level detection circuit S Q R IRQn input Clear signal Note: n: 2 to 0 Figure 5.2 Block Diagram of Interrupts IRQ2 to IRQ0 Rev. 3.00 Mar 17, 2006 page 88 of 706 REJ09B0303-0300 IRQn interrupt request Section 5 Interrupt Controller Figure 5.3 shows the timing of IRQnF setting. φ IRQn input pin IRQnF Figure 5.3 Timing of IRQnF Setting The vector numbers for IRQ2 to IRQ0 interrupt exception handling are 7 to 5. Detection of IRQ2 to IRQ0 interrupts does not depend on whether the relevant pin has been set for input or output. Therefore, when a pin is used as an external interrupt input pin, do not clear the corresponding DDR bit to 0 and use the pin as an I/O pin for another function. As interrupt request flags IRQ2F to IRQ0F are set when the setting condition is met, regardless of the IER setting, only the necessary flags should be referenced. 5.3.2 Internal Interrupts There are 26 sources (30 sources in the version with an on-chip USB) for internal interrupts from on-chip supporting modules. For each on-chip supporting module there are flags that indicate the interrupt request status, and enable bits that select enabling or disabling of these interrupts. If any one of these is set to 1, an interrupt request is issued to the interrupt controller. 5.3.3 Interrupt Exception Vector Table Table 5.3 shows interrupt exception handling sources, vector addresses, and interrupt priorities. For default priorities, the lower the vector number, the higher the priority. Priorities within a module are fixed as shown in table 5.3. Rev. 3.00 Mar 17, 2006 page 89 of 706 REJ09B0303-0300 Section 5 Interrupt Controller Table 5.3 Interrupt Exception Handling Sources, Vector Addresses, and Interrupt Priorities Interrupt Source Origin of Interrupt Source Vector Number Vector Address Priority NMI External pin 4 H'0008 High IRQ0 5 H'000A IRQ1 6 H'000C IRQ2 7 H'000E Reserved — 8 to 12 H'0010 to H'0018 WOVI0 (interval timer) Watchdog timer 0 13 H'001A ADI (A/D conversion end) A/D 14 H'001C ICIA (input capture A) Free-running timer 15 H'001E ICIB (input capture B) 16 H'0020 ICIC (input capture C) 17 H'0022 ICID (input capture D) 18 H'0024 OCIA (output compare A) 19 H'0026 OCIB (output compare B) 20 H'0028 FOVI (overflow) 21 H'002A CMIA0 (compare-match A) 22 H'002C CMIB0 (compare-match B) 23 H'002E OVI0 (overflow) 24 H'0030 25 H'0032 CMIB1 (compare-match B) 26 H'0034 OVI1 (overflow) 27 H'0036 CMIA1 (compare-match A) 8-bit timer channel 0 8-bit timer channel 1 Rev. 3.00 Mar 17, 2006 page 90 of 706 REJ09B0303-0300 Low Section 5 Interrupt Controller Origin of Interrupt Source Vector Number Vector Address Priority 8-bit timer channels Y, X 28 H'0038 High 29 H'003A OVIY (overflow) 30 H'003C ICIX (input capture X) 31 H'003E Interrupt Source CMIAY (compare-match A) CMIBY (compare-match B) Reserved — 32 to 35 H'0040 to H'0046 ERI0 (receive error 0) SCI channel 0 36 H'0048 RXI0 (reception completed 0) 37 H'004A TXI0 (transmit data empty 0) 38 H'004C TEI0 (transmission end 0) 39 H'004E Reserved — 40 to 43 H'0050 to H'0056 IICI0 (1-byte transmission/ reception completed) IIC channel 0 44 H'0058 45 H'005A DDCSWI (format switch) IICI1 (1-byte transmission/ reception completed) IIC channel 1 46 H'005C Reserved — 47 to 49 H'005E to H'0062 USBIA USB 50 H'0064 USBIB 51 H'0066 USBIC 52 H'0068 USBID 53 H'006A Low Rev. 3.00 Mar 17, 2006 page 91 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.4 Interrupt Operation 5.4.1 Interrupt Operation NMI interrupts are accepted at all times except in the reset state and the hardware standby state. In the case of IRQ interrupts and on-chip supporting module interrupts, an enable bit is provided for each interrupt. Clearing an enable bit to 0 disables the corresponding interrupt request. Interrupt sources for which the enable bits are set to 1 are controlled by the interrupt controller. Table 5.4 shows the interrupt control modes. Table 5.4 Interrupt Control Modes SYSCR Interrupt Control Mode INTM1 INTM0 Interrupt Mask Bits Description 0 0 0 I Interrupt mask control is performed by the I bit Figure 5.4 shows a block diagram of the priority decision circuit. I Interrupt source Interrupt acceptance control Default priority determination Vector number Figure 5.4 Block Diagram of Interrupt Control Operation Rev. 3.00 Mar 17, 2006 page 92 of 706 REJ09B0303-0300 Section 5 Interrupt Controller Interrupt Acceptance Control: In interrupt control mode 0, interrupt acceptance control is performed by means of the I bit in CCR. Table 5.5 shows the interrupts selected in each interrupt control mode. Table 5.5 Interrupts Selected in Each Interrupt Control Mode Interrupt Mask Bits Interrupt Control Mode I Selected Interrupts 0 0 All interrupts 1 NMI interrupts Default Priority Determination: The priority is determined for the selected interrupt, and a vector number is generated. Interrupt sources with a lower priority than the accepted interrupt source are held pending. Table 5.6 shows operations and control signal functions in each interrupt control mode. Table 5.6 Operations and Control Signal Functions in Each Interrupt Control Mode Interrupt Control Mode 0 Interrupt Acceptance Control Setting INTM1 INTM0 0 0 Determination I O IM O Legend: O: Interrupt operation control performed IM: Used as interrupt mask bit Rev. 3.00 Mar 17, 2006 page 93 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.4.2 Interrupt Control Mode 0 Enabling and disabling of IRQ interrupts and on-chip supporting module interrupts can be set by means of the I bit in the CPU’s CCR. Interrupts are enabled when the I bit is cleared to 0, and disabled when set to 1. Figure 5.5 shows a flowchart of the interrupt acceptance operation in this case. 1. If an interrupt source occurs when the corresponding interrupt enable bit is set to 1, an interrupt request is sent to the interrupt controller. 2. If a number of interrupt requests are generated at the same time, the interrupt request with the highest priority according to the priority system shown in table 5.3 is selected. 3. The I bit is then referenced. If the I bit is cleared to 0, the interrupt request is accepted. If the I bit is set to 1, only an NMI interrupt is accepted, and other interrupt requests are held pending. 4. When an interrupt request is accepted, interrupt exception handling starts after execution of the current instruction has been completed. 5. The PC and CCR are saved to the stack area by interrupt exception handling. The PC saved on the stack shows the address of the first instruction to be executed after returning from the interrupt handling routine. 6. Next, the I bit in CCR is set to 1. This disables all interrupts except NMI. 7. A vector address is generated for the accepted interrupt, and execution of the interrupt handling routine starts at the address indicated by the contents of that vector address. Rev. 3.00 Mar 17, 2006 page 94 of 706 REJ09B0303-0300 Section 5 Interrupt Controller Program execution state No Interrupt generated? Yes Yes NMI? No Hold pending IRQ0? No Yes IRQ1? Yes No IICI1*? Yes No I = 0? Yes Save PC and CCR I←1 Read vector address Branch to interrupt handling routine Note: * The built-in USB version is USBID. Figure 5.5 Flowchart of Procedure Up to Interrupt Acceptance Rev. 3.00 Mar 17, 2006 page 95 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 96 of 706 REJ09B0303-0300 (1) (2) (4) (3) (5) (6) (7) (8) (9) (10) Internal data bus (2) (1) (4) (3) Internal operation (1) (5) Stack (7) (6) (9) (8) Vector fetch Internal operation Instruction prefetch address (Not executed. This is the contents of the saved PC, the return address.) Instruction code (Not executed.) Instruction prefetch address (Not executed.) SP-2 SP-4 Saved CCR Vector address Interrupt handling routine start address (vector address contents) First instruction of interrupt handling routine Internal write signal Internal read signal Internal address bus Interrupt request signal φ Instruction prefetch (10) (9) Interrupt handling routine instruction prefetch 5.4.3 Interrupt level determination Wait for end of instruction Interrupt acceptance Section 5 Interrupt Controller Interrupt Exception Handling Sequence Figure 5.6 shows the interrupt exception handling sequence. Figure 5.6 Interrupt Exception Handling Section 5 Interrupt Controller 5.4.4 Interrupt Response Times Table 5.7 shows interrupt response times—the interval between generation of an interrupt request and execution of the first instruction in the interrupt handling routine. Table 5.7 Interrupt Response Times Number of States No. Item 1 Interrupt priority determination* 2 Number of wait states until executing instruction ends* 3 PC, CCR stack save 4 4 Vector fetch 2 5 3 Instruction fetch* 6 Internal processing* Total Notes: 1. 2. 3. 4. Normal Mode 1 3 2 1 to 13 4 4 4 18 to 30 Two states in case of internal interrupt. Refers to MULXS and DIVXS instructions. Except EEPMOV instruction. Prefetch after interrupt acceptance and interrupt handling routine prefetch. Internal processing after interrupt acceptance and internal processing after vector fetch. Rev. 3.00 Mar 17, 2006 page 97 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.5 Usage Notes 5.5.1 Contention between Interrupt Generation and Disabling When an interrupt enable bit is cleared to 0 to disable interrupts, the disabling becomes effective after execution of the instruction. In other words, when an interrupt enable bit is cleared to 0 by an instruction such as BCLR or MOV, if an interrupt is generated during execution of the instruction, the interrupt concerned will still be enabled on completion of the instruction, and so interrupt exception handling for that interrupt will be executed on completion of the instruction. However, if there is an interrupt request of higher priority than that interrupt, interrupt exception handling will be executed for the higher-priority interrupt, and the lower-priority interrupt will be ignored. The same also applies when an interrupt source flag is cleared to 0. Figure 5.7 shows an example in which the CMIEA bit in 8-bit timer register TCR is cleared to 0. TCR write cycle by CPU CMIA exception handling φ Internal address bus TCR address Internal write signal CMIEA CMFA CMIA interrupt signal Figure 5.7 Contention between Interrupt Generation and Disabling The above contention will not occur if an enable bit or interrupt source flag is cleared to 0 while the interrupt is masked. Rev. 3.00 Mar 17, 2006 page 98 of 706 REJ09B0303-0300 Section 5 Interrupt Controller 5.5.2 Instructions that Disable Interrupts Instructions that disable interrupts are LDC, ANDC, ORC, and XORC. After any of these instructions is executed, all interrupts, including NMI, are disabled and the next instruction is always executed. When the I bit is set by one of these instructions, the new value becomes valid two states after execution of the instruction ends. 5.5.3 Interrupts during Execution of EEPMOV Instruction With the EEPMOV instruction, an interrupt request (including NMI) issued during the transfer is not accepted until the move is completed. The EEPMOV instruction cannot be used in the H8/3577 Group and H8/3567 Group. Rev. 3.00 Mar 17, 2006 page 99 of 706 REJ09B0303-0300 Section 5 Interrupt Controller Rev. 3.00 Mar 17, 2006 page 100 of 706 REJ09B0303-0300 Section 6 Bus Controller Section 6 Bus Controller 6.1 Overview As the H8/3577 Group and H8/3567 Group do not have external expansion functions, they do not incorporate a bus controller function. However, from the viewpoint of maintaining software compatibility with similar products, care must be taken not to set inappropriate values in the bus controller related control registers. 6.2 Register Descriptions 6.2.1 Bus Control Register (BCR) Bit 7 6 5 4 3 BRSTRM BRSTS1 BRSTS0 2 1 0 ICIS1 ICIS0 — IOS1 IOS0 Initial value 1 1 0 1 0 1 1 1 Read/Write R/W R/W R R/W R R/W R/W R/W Bits 7 and 6—Idle Cycle Insert 1 and 0 (ICIS1, ICIS0): Do not write 0 to these bits. Bit 5—Burst ROM Enable (BRSTRM): Do not write 1 to this bit. Bit 4—Burst Cycle Select 1 (BRSTS1): Do not write 0 to this bit. Bit 3—Burst Cycle Select 0 (BRSTS0): Do not write 1 to this bit. Bit 2—Reserved: Do not write 0 to this bit. Bits 1 and 0—IOS Select 1 and 0 (IOS1, IOS0): Do not write 0 to these bits. Rev. 3.00 Mar 17, 2006 page 101 of 706 REJ09B0303-0300 Section 6 Bus Controller 6.2.2 Wait State Control Register (WSCR) Bit 7 6 5 4 3 2 1 0 RAMS RAM0 ABW AST WMS1 WMS0 WC1 WC0 Initial value 0 0 1 1 0 0 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit 7—RAM Select (RAMS)/Bit 6—RAM Area Setting (RAM0): Reserved bits. Bit 5—Bus Width Control (ABW): Do not write 0 to this bit. Bit 4—Access State Control (AST): Do not write 0 to this bit. Bits 3 and 2—Wait Mode Select 1 and 0 (WMS1, WMS0): Do not write 1 to these bits. Bits 1 and 0—Wait Count 1 and 0 (WC1, WC0): Do not write 0 to these bits. Rev. 3.00 Mar 17, 2006 page 102 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Section 7 Universal Serial Bus Interface (USB) It is built in the H8/3567U and H8/3564U Group and not in the H8/3577, H8/3574, H8/3567 and H8/3564 Group. 7.1 Overview The H8/3567U and H8/3564U have an on-chip universal serial bus (USB) comprising hubs and a function. The universal serial bus is an interface for personal computer peripherals whose standardization is being promoted by a core group of companies, including Intel Corporation. The USB is provided with a number of device classes to handle the great variety of personal computer peripheral devices. The USB in the H8/3567U and H8/3564U are targeted at the hub device class and HID (Human Interface Device) class (mainly a monitor device class). 7.1.1 Features • Compound device conforming to USB standard* Apart from initial settings and power-down mode settings, USB hubs decode and execute hub class commands automatically, independently of CPU operations USB function decodes and executes standard commands Device class commands are decoded and executed by the CPU (firmware creation required) • Five downstream hubs and one function One down stream is connected internally to the USB function Internal downstream disconnection function (Only power-down mode USB hubs operable) Four sets of downstream external pins Automatic control of downstream port external power supply control IC (individual port control) • Three-endpoint monitor device class function EP0: USB control endpoint (dedicated to control transfer) EP1, EP2: Monitor control endpoints (dedicated to interrupt transfer) EP0I, EP0O, and EP2 can use a maximum 16-byte FIFO (maximum packet size of 8 bytes), and EP1 can use a maximum 32-byte FIFO (maximum packet size of 16 bytes) • Supports 12 Mbps high-speed transfer mode • Built-in 12 MHz clock pulse generator and frequency division/multiplication circuit • Built-in bus driver/receiver Driven by DrVSS/DrVCC (3.3 V) Rev. 3.00 Mar 17, 2006 page 103 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Note: * The USB function conforms to USB Standard 1.1 and the USB hub to USB Standard 1.0. 7.1.2 Block Diagram Figure 7.1 shows a block diagram of the USB. Internal data bus Module data bus Bus I/F FIFO control EPDR2 FVSR2 EPSZR1 EPDR1 FVSR1 EPDR0I FVSR0I EPDR0O FVSR0O Address bus Data bus Bus driver/ receiver Registers EPSTLR PTTER EPDIR USBIER EPRSTR USBIFR DEVRSMR TSFR INTSELR0 TFFR USBCSR0 INTSELR1 HOCCR USBCR UPLLCR UPRTCR UTESTR0 UTESTR1 UTESTR2 Internal interrupts Interrupt I/F USB operating clock Clock selection FIFO 64 bytes Connection selection USD+ USD− φ (XTAL12, EXTAL12) PLL DrVCC DrVSS USB hub core Connection selection Bus driver/ receiver Power supply control IC Control DS2D+ DS2D− Legend: EPDR2: EPDR1: EPDR0I: EPDR0O: FVSR2: FVSR1: FVSR0I: FVSR0O: EPSZR1: PTTER: USBIER: USBIFR: TSFR: TFFR: USBCSR0: EPSTLR: EPDIR: Endpoint data register 2 Endpoint data register 1 Endpoint data register 0I Endpoint data register 0O FIFO valid size register 2 FIFO valid size register 1 FIFO valid size register 0I FIFO valid size register 0O Endpoint size register 1 Packet transmit enable register USB interrupt enable register USB interrupt flag register Transfer success flag register Transfer fail flag register USB control/status register 0 Endpoint stall register Endpoint direction register USB function core DS3D+ DS4D+ DS5D+ DS3D− DS4D− DS5D− EPRSTR: DEVRSMR: INTSELR0: INTSELR1: HOCCR: USBCR: UPLLCR: UPRTCR: UTESTR0: UTESTR1: UTESTR2: USD+: USD–: DS2D+: DS2D–: DS3D+: DS3D–: ENP2, ENP3 ENP4, ENP5 Endpoint reset register Device resume register Interrupt source select register 0 Interrupt source select register 1 Hub overcurrent control register USB control register USB PLL control register USB port control register USB test register 0 USB test register 1 USB test register 2 Upstream data + pin Upstream data − pin Downstream 2 data + pin Downstream 2 data − pin Downstream 3 data + pin Downstream 3 data − pin OCP2, OCP3 OCP4, OCP5 DS4D+: DS4D–: DS5D+: DS5D–: XTAL12: EXTAL12: DrVCC: DrVSS: OCP2: OCP3: OCP4: OCP5: ENP2: ENP3: ENP4: ENP5: Figure 7.1 Block Diagram of USB Rev. 3.00 Mar 17, 2006 page 104 of 706 REJ09B0303-0300 Downstream 4 data + pin Downstream 4 data − pin Downstream 5 data + pin Downstream 5 data − pin USB clock oscillator pin USB clock oscillator pin Bus driver power supply pin Bus driver ground pin Overcurrent detection pin 2 Overcurrent detection pin 3 Overcurrent detection pin 4 Overcurrent detection pin 5 Power supply output enable pin 2 Power supply output enable pin 3 Power supply output enable pin 4 Power supply output enable pin 5 Section 7 Universal Serial Bus Interface (USB) 7.1.3 Pin Configuration Table 7.1 shows the pins used by the USB. Table 7.1 USB Pins Name Abbreviation I/O Function Upstream data + pin USD+ Input/output USB hub/function data input/output Upstream data – pin USD– Input/output Downstream 2 data + pin DS2D+ Input/output Downstream 2 data – pin DS2D– Input/output Downstream 3 data + pin DS3D+ Input/output Downstream 3 data – pin DS3D– Input/output Downstream 4 data + pin DS4D+ Input/output USB hub repeater input/output (port 2) USB hub repeater input/output (port 3) USB hub repeater input/output (port 4) Downstream 4 data – pin DS4D– Input/output Downstream 5 data + pin DS5D+ Input/output Downstream 5 data – pin DS5D– Input/output Overcurrent detection pins 2 to 5 OCP2 to OCP5 Input Power supply control IC overcurrent detection signal input Power supply output enable ENP2 to control pins 2 to 5 ENP5 Output Power supply control IC power output enable signal output USB clock oscillator pin XTAL12 Input 12 MHz crystal oscillation USB clock oscillator pin EXTAL12 Input USB hub repeater input/output (port 5) Bus Driver power supply pin DrVCC Input Bus driver/receiver, port D power supply Bus Driver ground pin Input Bus driver/receiver, port D ground 7.1.4 DrVSS Register Configuration The USB register configuration is shown in table 7.2. Registers relating to USB hub initialization and status display are USBCR, USBCSR0, HOCCR, and UPLLCR, as well as some bits in the test registers; the other registers relate to the USB function. When USBCR, USBCSR0, HOCCR, and UPLLCR are all in the initial state, the USB module is completely disabled, and ports C and D function as I/O ports. When accessing a USB register, the USBE bit in STCR must be set to 1. Rev. 3.00 Mar 17, 2006 page 105 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Table 7.2 USB Registers Name Abbreviation R/W Initial Value Address Endpoint data register 2 EPDR2 R or W* H'00 H'FDE1 FIFO valid size register 2 FVSR2 R H'0010 H'FDE2 Endpoint size register 1 EPSZR1 R/W H'44 H'FDE4 1 Endpoint data register 1 EPDR1 W H'00 H'FDE5 FIFO valid size register 1 FVSR1 R H'0010 H'FDE6 Endpoint data register 0O EPDR0O R H'00 H'FDE9 FIFO valid size register 0O FVSR0O R H'0000 H'FDEA Endpoint data register 0I EPDR0I W H'00 H'FDED FIFO valid size register 0I FVSR0I R H'0010 H'FDEE Packet transmit enable register PTTER 2 R/(W)* H'00 H'FDF0 USB interrupt enable register USBIER R/W H'00 H'FDF1 USB interrupt flag register USBIFR H'00 H'FDF2 Transfer success flag register TSFR R/(W)* 3 R/(W)* H'00 H'FDF3 TFFR 3 R/(W)* H'00 H'FDF4 Transfer fail flag register 3 USB control/status register 0 USBCSR0 R/W H'00 H'FDF5 Endpoint stall register EPSTLR R/W H'00 H'FDF6 Endpoint direction register EPDIR R/W H'FC H'FDF7 EPRSTR 2 R/(W)* H'00 H'FDF8 Device resume register DEVRSMR 2 R/(W)* H'00 H'FDF9 Interrupt source select register 0 INTSELR0 R/W H'00 H'FDFA Interrupt source select register 1 INTSELR1 R/W H'00 H'FDFB Hub overcurrent control register HOCCR R/W H'00 H'FDFC USB control register USBCR R/W H'7F H'FDFD USB PLL control register UPLLCR R/W H'01 H'FDFE USB port control register UPRTCR R/W H'00 H'FDC0 USB test register 0 UTESTR0 R/W H'00 H'FDC1 USB test register 1 UTESTR1 R/W H'00 H'FDC2 USB test register 2 UTESTR2 R/W H'FF H'FDFF Other test registers — — — H'FDC3 to H'FDE0 Endpoint reset register Rev. 3.00 Mar 17, 2006 page 106 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Name Abbreviation R/W Initial Value Address Serial timer control register STCR R/W H'00 H'FFC3 Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 Notes: 1. Write-only or read-only depending on the transfer direction set in the endpoint direction register. 2. Only 1 can be written. 3. Only 0 can be written after reading 1 to clear the flags. 7.2 Register Descriptions In the USB protocol, the host transmits a token to initiate a single data transfer (a transaction). A transaction consists of a token packet, data packet, and handshake packet. The token packet contains the address endpoint of the transfer target device and the transfer type, the data packet contains data, and the handshake packet contains information relating to transfer setup/non-setup. In data transfer from the host to a slave, the host transmits an OUT token or SETUP token, followed by data (an OUT or SETUP transaction). In data transfer from a slave to the host, the host transmits an IN token and waits for data from the slave (an IN transaction). In the following descriptions, these host-based IN and OUT operations may be referred to as “input” and “output.” Also, items relating to host input transfer may be designated “IN” (IN transaction, IN-FIFO, EP0in, etc.), while items relating to host output transfer are designated “OUT” (OUT transaction, OUT-FIFO, EP0out, etc.). Where an explicit expression such as “transmitted by the host” or “received by the host” is not used, the terms “transmission” and “reception” refer to transmission and reception from the standpoint of the USB module and slave CPU. 7.2.1 USB Data FIFO The FIFO, together with EPDR, functions as an intermediary role in data transfer between the H8 CPU (slave) and the USB function. The USB function uses the FIFO to execute data transfer to and from the USB host (host). The H8/3567U and H8/3564U have an on-chip 64-byte FIFO. This FIFO is divided into four 16byte FIFOs, used for endpoint 0 host input transfer and host output transfer (control transfer), endpoint 1 host input transfer (interrupt transfer), and endpoint 2 host input transfer or host output transfer. If endpoint 2 is not used, a 32-byte length can be selected for the endpoint 1 FIFO. The maximum data packet size is set at half the number of FIFO bytes. Rev. 3.00 Mar 17, 2006 page 107 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) In host input transfer, all the data to be transmitted from the slave is written to the FIFO before slave transmission is started. In host output transfer, the slave reads all the data from the FIFO after host output transfer is completed. 7.2.2 Endpoint Size Register 1 (EPSZR1) Bit 7 6 EP1SZ3 5 4 3 2 1 0 EP1SZ2 EP1SZ1 EP1SZ0 EP2SZ3 EP2SZ2 EP2SZ1 EP2SZ0 Initial value 0 1 0 0 0 1 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W EPSZR1 specifies the number of FIFO bytes used for each USB function endpoint 1 and 2 host input transfer/host output transfer. The number of bytes in the endpoint 0 FIFO is fixed at 16. Both host input (EP0in) and host output (EP0out) can be selected for endpoint 0, host input for endpoint 1, and host input and host output for endpoint 2. With the H8/3567U and H8/3564U, when endpoints 1 and 2 are both used, set a 16-byte size for the respective FIFOs. When only endpoint 1 is used, set a 16- or 32-byte size. If the 32-byte size is selected, set 0 as the endpoint 2 FIFO size. EPSZR1 is initialized to H'44 by a system reset or a function soft reset. EPSZR1 Bits 7 to 4 EP1 FIFO size EPSZR1 Bits 3 to 0 EP2 FIFO size Bit 7 Bit 3 Bit 6 Bit 2 Bit 5 Bit 1 Bit 4 Bit 0 SZ3 SZ2 SZ1 SZ0 Operating Mode 0 0 0 0 FIFO size = 0 bytes (settable for EP2 only) 1 Setting prohibited 0 Setting prohibited 1 Setting prohibited 0 FIFO size = 16 bytes 1 FIFO size = 32 bytes (settable for EP1 only) 0 Setting prohibited 1 Setting prohibited — Setting prohibited 1 1 0 1 1 — — Rev. 3.00 Mar 17, 2006 page 108 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) 7.2.3 Endpoint Data Registers 0I, 0O, 1, 2 (EPDR0I, EPDR0O, EPDR1, EPDR2) Bit Initial value Read/ Write 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 EPDR0I W W W W W W W W EPDR0O R R R R R R R R EPDR1 W EPDR2 Note: 7 * W W W W W W W * * * * * * * R or W R or W R or W R or W R or W R or W R or W R or W* Write-only or read-only depending on the transfer direction set in the endpoint direction register. The EPDR registers play an intermediary role in data transfer between the CPU and FIFO for each host input transfer/host output transfer involving the respective USB function endpoints. EPDR0I and EPDR1 are used for host input transfer, and so are write-only registers; if read, the contents of the read data are not guaranteed. EPDR0O is used for host output transfer, and so is a read-only register; it cannot be written to. For EPDR2, the endpoint transfer direction is determined by the endpoint direction register. EPDR2 is a write-only register when designated for host input transfer, and a read-only register when designated for host output transfer. If EPDR2 is read when functioning as a write-only register, the contents of the read data are not guaranteed. When EPDR2 is functioning as a readonly register, it cannot be written to. Data written to EPDR0I, EPDR1, or EPDR2 (when a write-only register) is stored in the FIFO, and is made valid by setting the EPTE bit in the packet transmit enable register (PTTER). Valid data is transferred to the USB function, and transferred to the host, in accordance with a USB function request. Data transferred from the host is stored in the FIFO by the USB function, and becomes valid when all the data packet bytes have been received and an ACK handshake is transmitted. When EPDR0O or EPDR2 (when a read-only register) is read, the contents are stored in the FIFO, and when the data is valid it is read in the order in which it was transferred. The EPDR registers are initialized to H'00 by a system reset or a function soft reset. Rev. 3.00 Mar 17, 2006 page 109 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.2.4 FIFO Valid Size Registers 0I, 0O, 1, 2 (FVSR0I, FVSR0O, FVSR1, FVSR2) FVSR0IH, FVSR0OH, FVSR1H, FVSR2H FVSR0IL, FVSR0OL, FVSR1L, FVSR2L Bit 7 6 5 4 3 2 1 0 7 6 5 — — — — — — N9 N8 N7 N6 N5 Initial value 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R Note: * 4 3 N4 N3 0/1* 0 R R 2 1 0 N2 N1 N0 0 0 0 R R R The initial value of bit N4 is 0 in FVSR0O, and 1 in the other FVSR registers. The FVSR registers indicate the number of valid data bytes in the FIFO for each host input/host output involving the respective USB function endpoints. In host input transfer, the FVSR register indicates the number of bytes that the slave CPU can write to the FIFO (the FIFO size minus the number of bytes written to the FIFO by the slave CPU but not read (transmitted) by the USB function). In host output transfer, the FVSR register indicates the number of bytes received and written to the FIFO by the USB function but not read by the slave CPU. In host input transfer, the FVSR value is decremented by the number of bytes written when the slave CPU writes to EPDR and sets the EPTE bit in PTTER, and is incremented by the number of bytes read when the USB function reads the FIFO and receives an ACK handshake from the host. In host output transfer, the FVSR value is incremented by the number of bytes written when the USB function writes to the FIFO and transmits an ACK handshake, and is decremented by 1 each time the slave CPU reads EPDR. If a transfer error occurs, data retransfer may be necessary. In this case, the FVSR value is not changed and the FIFO for the relevant channel is rewound. In the USB protocol, for each endpoint DATA0 and DATA1 packets are transmitted and received alternately when data transfer is performed. This toggling between DATA0 and DATA1 also serves as an indicator of whether or not data transfer has been performed normally. If DATA0/DATA1 toggling is not performed normally in host output transfer, the USB function will abort processing of that transaction and the FVSR value will not change. Since the FVSR registers are 2-byte registers and the H8’s FIFOs are 16 or 32 bytes in length, the FIFO status can be indicated in the lower byte alone. Only the lower byte of the FVSR registers should be read. The upper byte of the FVSR registers cannot be accessed directly. When the lower byte is read, the upper byte is transferred to a temporary register, and when the upper byte is read, the contents of this temporary register are read. When a word read is used on an FVSR register, the operation is Rev. 3.00 Mar 17, 2006 page 110 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) automatically divided into two byte accesses, with the upper byte read first, followed by the lower byte. Caution is required in this case, since the upper byte value that is read is the value at the point when the lower byte was read previously. FVSR0I and FVSR1 are automatically initialized to H'0010 and H'0000, respectively, when a SETUP token is received. The FVSR registers are initialized by a system reset or a function soft reset. The initial value depends on the transfer direction and FIFO size determined by EPDIR and EPSZR. 7.2.5 Endpoint Direction Register (EPDIR) Bit 7 6 5 4 3 2 1 0 — — — — EP2DIR EP1DIR — — Initial value 1 1 1 1 1 1 0 0 Read/Write R R R R R/W R/W R R EPDIR controls the data transfer direction for USB function endpoints other than endpoint 0. With the H8/3567U and H8/3564U, EP1 should be designated for host input transfer and EP2 for host input transfer or host output transfer. EPDIR is initialized to H'FC by a system reset or a function soft reset. Bit 3—Endpoint 2 Data Transfer Direction Control Flag (EP2DIR): Switches the endpoint 2 data transfer direction. Bit 3 EP2DIR Description 0 Endpoint 2 is designated for host output transfer 1 Endpoint 2 is designated for host input transfer (Initial value) Rev. 3.00 Mar 17, 2006 page 111 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 2—Endpoint 1 Data Transfer Direction Control Flag (EP1DIR): Switches the endpoint 1 data transfer direction. This bit must not be cleared to 0. Bit 2 EP1DIR Description 0 Setting prohibited 1 Endpoint 1 is designated for host input transfer 7.2.6 Packet Transmit Enable Register (PTTER) Bit Initial value Read/Write Note: (Initial value) * 7 6 5 4 3 2 1 0 — — — — EP2TE EP1TE EP0ITE — 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R R R R Only 1 can be written. PTTER contains control bits (EPTE) that control the FIFO valid size registers for USB function host input transfer. In the USB protocol, communication is carried out using packets. The minimum unit of data transfer is a transaction, and a transaction is made up of a token packet, data packet, and handshake packet. In host input transfer, the USB function receives an IN token (packet). If operation has not stalled, in response to this token the USB function must transmit a data packet or, if there is no data, a NAK handshake. When EPTE is set to 1 after the data to be transmitted by the USB function has been written to the FIFO by the slave CPU, the FVSR contents are updated. This enables transmission of the data written to the FIFO. This EPTE-bit data transmission control prevents data transmission from being done while the slave CPU is writing data to the FIFO. The EPTE can only be written with 1, and are always read as 0. Rev. 3.00 Mar 17, 2006 page 112 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 3—Endpoint 2 Packet Transmit Enable (EP2TE): Updates endpoint 2 FVSR2 when the EP2DIR bit is set to 1. Bit 3 EP2TE Description 0 Normal read value (1) (Initial value) [1 write] Endpoint 2 IN-FIFO FVSR2 is updated Bit 2—Endpoint 1 Packet Transmit Enable (EP1TE): Updates endpoint 1 FVSR1. Bit 2 EP1TE Description 0 Normal read value (1) (Initial value) [1 write] Endpoint 1 IN-FIFO FVSR1 is updated Bit 1—Endpoint 0I Packet Transmit Enable (EP0ITE): Updates endpoint 0 FVSR0I. Bit 1 EP0ITE Description 0 Normal read value (1) [1 write] (Initial value) Endpoint 0 IN-FIFO FVSR0I is updated 7.2.7 USB Interrupt Enable Register (USBIER) Bit 7 6 5 4 3 2 1 0 — — BRSTE SOFE SPNDE TFE TSE SETUPE Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W USBIER contains enable bits that enable interrupts from the USB function to the slave CPU. USBIER is initialized to H'00 by a system reset or a function soft reset. Rev. 3.00 Mar 17, 2006 page 113 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 5—Bus Reset Interrupt Enable (BRSTE): Enables or disables bus request interrupts to the internal CPU. Bit 5 BRSTE Description 0 USB function bus request interrupts disabled 1 USB function bus request interrupts enabled (Initial value) Bit 4—SOF Interrupt Enable (SOFE): Enables or disables SOF (Start of Frame) interrupts to the internal CPU. Bit 4 SOFE Description 0 USB function SOF interrupts disabled 1 USB function SOF interrupts enabled (Initial value) Bit 3—Suspend Interrupt Enable (SPNDE): Enables or disables suspend OUT interrupts and suspend IN interrupts to the internal CPU. Bit 3 SPNDE Description 0 USB function suspend OUT interrupts and suspend IN interrupts disable (Initial value) 1 USB function suspend OUT interrupts and suspend IN interrupts enabled Bit 2—Transfer Failed Interrupt Enable (TFE): Enables or disables transfer failed interrupts to the internal CPU. Bit 2 TFE Description 0 USB function transfer failed interrupts disabled 1 USB function transfer failed interrupts enabled Rev. 3.00 Mar 17, 2006 page 114 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) Bit 1—Transfer Successful Interrupt Enable (TSE): Enables or disables transfer successful interrupts to the internal CPU. Bit 1 TSE Description 0 USB function transfer successful interrupts disabled 1 USB function transfer successful interrupts enabled (Initial value) Bit 0—Setup Interrupt Enable (SETUPE): Enables or disables setup interrupts to the internal CPU. Bit 0 SETUPE Description 0 USB function setup interrupts disabled 1 USB function setup interrupts enabled 7.2.8 USB Interrupt Flag Register (USBIFR) Bit Initial value Read/Write Note: (Initial value) * 7 6 5 4 3 TS TF — BRSTF SOFF 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R R 2 1 0 SPNDOF SPNDIF SETUPF Only 0 can be written, after reading 1, to clear the flag. USBIFR contains interrupt flags that generate interrupts from the USB function to the slave CPU. The USB module has four interrupt sources (USBIA, USBIB, USBIC, and USBID). USBIA is a dedicated setup interrupt. A single transfer successful interrupt or transfer failed interrupt can be assigned to USBIB and USBIC. All other interrupts (all transfer successful interrupts and transfer failed interrupts, bus reset interrupts, SOF interrupts, and suspend OUT and suspend IN interrupts) are assigned to USBID. USBIFR is initialized to H'00 by a system reset or a function soft reset. Rev. 3.00 Mar 17, 2006 page 115 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 7—Transfer Successful Interrupt Status (TS): Status flag that indicates that transfer has ended normally at a USB function endpoint. When the TSE bit is 1, USBID interrupt request is sent to the slave CPU, but if a setting has been made for the source that set TS to 1 to request USBIB or USBIC interrupt, has priority for processing in accordance with the priority order in the slave CPU’s interrupt controller (INTC). TS is a read-only flag. Bit 7 TS Description 0 All bits in transfer success flag register (TSFR) are 0 1 At least one bit in transfer success flag register (TSFR) is 1 (Initial value) Bit 6—Transfer Failed Interrupt Status (TF): Status flag that indicates that transfer has ended abnormally at a USB function endpoint. When the TFE bit is 1, USBID interrupt request is sent to the slave CPU, but if a setting has been made for the source that set TF to 1 to request USBIB or USBIC interrupt, has priority for processing in accordance with the priority order in the slave CPU’s interrupt controller (INTC). TF is a read-only flag. Bit 6 TF Description 0 All bits in transfer fail flag register (TFFR) are 0 1 At least one bit in transfer fail flag register (TFFR) is 1 (Initial value) Bit 4—Bus Reset Interrupt Flag (BRSTF): Status flag that indicates that the USB function has detected a bus reset from upstream. When the BRSTE bit is 1, USBID interrupt request is sent to the slave CPU. Rev. 3.00 Mar 17, 2006 page 116 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 4 BRSTF Description 0 [Clearing condition] (Initial value) When 0 is written to BRSTF after reading BRSTF = 1 1 [Setting condition] When USB function detects a bus reset from upstream Bit 3—SOF Interrupt Flag (SOFF): Status flag that indicates that the USB function has detected SOF (Start of Frame). When the SOFE bit is 1, USBID interrupt request is sent to the slave CPU. Bit 3 SOFF Description 0 [Clearing condition] (Initial value) When 0 is written to SOFF after reading SOFF = 1 1 [Setting condition] When USB function detects SOF (Start of Frame) Bit 2—Suspend OUT Interrupt Flag (SPNDOF): Status flag that indicates that the USB function has detected a change in the bus status, and has switched from the suspend state to the normal state. When the SPNDE bit is 1, USBID interrupt request is sent to the slave CPU. Bit 2 SPNDOF Description 0 [Clearing condition] (Initial value) When 0 is written to SPNDOF after reading SPNDOF = 1 1 [Setting condition] When USB function switches from suspend state to normal state Bit 1—Suspend IN Interrupt Flag (SPNDIF): Status flag that indicates that the USB function has detected a bus idle state lasting longer that the specified time, and has switched from the normal state to the suspend state. When the SPNDE bit is 1, USBID interrupt request is sent to the slave CPU. Rev. 3.00 Mar 17, 2006 page 117 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 1 SPNDIF Description 0 [Clearing condition] (Initial value) When 0 is written to SPNDIF after reading SPNDIF = 1 1 [Setting condition] When USB function switches from normal state to suspend state Bit 0—Setup Interrupt Flag (SETUPF): Status flag that indicates that USB function endpoint 0 has received a SETUP token. When the SETUPE bit is 1, USBIA interrupt request is sent to the slave CPU. Bit 0 SETUPF Description 0 [Clearing condition] (Initial value) When 0 is written to SETUPF after reading SETUPF = 1 1 [Setting condition] When USB function endpoint 0 receives SETUP token 7.2.9 Transfer Success Flag Register (TSFR) Bit Initial value Read/Write Note: * 7 6 5 4 3 2 1 0 — — — — EP2TS EP1TS EP0ITS EP0OTS 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R/(W)* R R R Only 0 can be written, after reading 1, to clear the flag. TSFR contains status flags (EPTS flags) that indicate that a USB function endpoint host input/host output transaction has ended normally. The condition for a normal end of a transaction is reception of an ACK handshake in host input transfer, or transmission of an ACK handshake in host output transfer. When at least one EPTS flag is set to 1, the TS flag in USBIFR is also set at the same time. The TS flag generates an interrupt to the slave CPU. The EPTS flags must be cleared to 0 in the interrupt handling routine. When all the EPTS flags are cleared, the TS flag is automatically cleared to 0. Only 0 can be written to the EPTS flags, after first reading 1. Rev. 3.00 Mar 17, 2006 page 118 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) When the USB function receives a SETUP token, the EP0ITS and EP0OTS flags are automatically cleared to 0. TSFR is initialized to H'00 by a system reset or a function soft reset. Bit 3—Endpoint 2 Transfer Success Flag (EP2TS): Indicates that an endpoint 2 host input transfer or host output transfer has ended normally. Bit 3 EP2TS 0 Description Endpoint 2 is in transfer standby state (Initial value) [Clearing condition] When 0 is written to EP2TS after reading EP2TS = 1 1 Endpoint 2 host input transfer (IN transaction) or host output transfer (OUT transaction) has ended normally [Setting conditions] • ACK handshake established after IN token reception and data transfer (ACK reception) • ACK handshake established after OUT token reception and data transfer (ACK transmission) Bit 2—Endpoint 1 Transfer Success Flag (EP1TS): Indicates that an endpoint 1 host input transfer has ended normally. Bit 2 EP1TS Description 0 Endpoint 1 is in transfer standby state (Initial value) [Clearing condition] When 0 is written to EP1TS after reading EP1TS = 1 1 Endpoint 1 host input transfer (IN transaction) has ended normally [Setting condition] ACK handshake established after IN token reception and data transfer (ACK reception) Bit 1—Endpoint 0 Host Input Transfer Success Flag (EP0ITS): Indicates that an endpoint 0 host input transfer has ended normally. Rev. 3.00 Mar 17, 2006 page 119 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 1 EP0ITS Description 0 Endpoint 0 is in host input transfer standby state (Initial value) [Clearing conditions] 1 • When 0 is written to EP0ITS after reading EP0ITS = 1 • When endpoint 0 receives a SETUP token Endpoint 0 host input transfer (IN transaction) has ended normally [Setting condition] ACK handshake established after IN token reception and data transfer (ACK reception) Bit 0—Endpoint 0 Host Output Transfer Success Flag (EP0OTS): Indicates that an endpoint 0 host output transfer has ended normally. Host output transfers to endpoint 0 include OUT transactions and SETUP transactions. These operations are the same in terms of data transfer, but differ as regards flag handling. Most commands transferred in SETUP transactions are processed within the USB function, in which case the EP0OTS flag is not set and the EP0OTF flag is. In the case of a command that cannot be processed within the USB function, the EP0OTS flag is set. Bit 0 EP0OTS Description 0 Endpoint 0 is in host output transfer standby state (Initial value) [Clearing conditions] 1 • When 0 is written to EP0OTS after reading EP0OTS = 1 • When endpoint 0 receives a SETUP token Endpoint 0 host output transfer (OUT transaction or SETUP transaction) has ended normally [Setting conditions] • ACK handshake established after OUT token reception and data transfer (ACK transmission) • When command received after SETUP token reception requires processing by the slave CPU Rev. 3.00 Mar 17, 2006 page 120 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.2.10 Transfer Fail Flag Register (TFFR) Bit Initial value Read/Write Note: * 7 6 5 4 3 2 1 0 — — — — EP2TF EP1TF EP0ITF EP0OTF 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R/(W)* R R R Only 0 can be written, after reading 1, to clear the flag. TFFR contains status flags (EPTF flags) that indicate that a USB function endpoint host input/host output transaction has not ended normally. The condition for an abnormal end of a transaction is NAK handshake reception, or NAK handshake transmission when there is no transfer data (FVSR = FIFO size (FIFO empty)), in host input transfer, or, in host output transfer, NAK handshake transmission due to a FIFO full condition, etc., or any of various communication errors (DATA0/DATA1 toggle error, bit stuffing error, bit count error, CRC error, transfer of a number of bytes exceeding MaxPktSz, etc.) during data transfer. When at least one EPTF flag is set to 1, the TF flag in USBIFR is also set at the same time. The TF flag generates an interrupt to the slave CPU. The EPTF flags must be cleared to 0 in the interrupt handling routine. When all the EPTF flags are cleared, the TF flag is automatically cleared to 0. Only 0 can be written to the EPTF flags, after first reading 1. When the USB function receives a SETUP token, the EP0ITF and EP0OTF flags are automatically cleared to 0. TFFR is initialized to H'00 by a system reset or a function soft reset. Rev. 3.00 Mar 17, 2006 page 121 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 3—Endpoint 2 Transfer Fail Flag (EP2TF): Indicates that an endpoint 2 host input transfer or host output transfer has not ended normally. Bit 3 EP2TF Description 0 Endpoint 2 is in transfer standby state (Initial value) [Clearing condition] When 0 is written to EP2TF after reading EP2TF = 1 1 Endpoint 2 host input transfer (IN transaction) or host output transfer (OUT transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception • Data transfer not possible due to FIFO full condition after OUT token reception (NAK transmission) • Data transfer errors after OUT token reception Bit 2—Endpoint 1 Transfer Fail Flag (EP1TF): Indicates that an endpoint 1 host input transfer has not ended normally. Bit 2 EP1TF Description 0 Endpoint 1 is in transfer standby state (Initial value) [Clearing condition] When 0 is written to EP1TF after reading EP1TF = 1 1 Endpoint 1 host input transfer (IN transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception (NAK transmission) Rev. 3.00 Mar 17, 2006 page 122 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 1—Endpoint 0 Host Input Transfer Fail Flag (EP0ITF): Indicates that an endpoint 0 host input transfer has not ended normally. Bit 1 EP0ITF Description 0 Endpoint 0 is in host input transfer standby state (Initial value) [Clearing conditions] 1 • When 0 is written to EP0ITF after reading EP0ITF = 1 • When endpoint 0 receives a SETUP token Endpoint 0 host input transfer (IN transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception (NAK transmission) Bit 0—Endpoint 0 Host Output Transfer Fail Flag (EP0OTF): Indicates that an endpoint 0 host output transfer has not ended normally. Host output transfers to endpoint 0 include OUT transactions and SETUP transactions. These operations are the same in terms of data transfer, but differ as regards flag handling. Most commands transferred in SETUP transactions are processed within the USB function, in which case the EP0OTS flag is not set and the EP0OTF flag is. In the case of a command that cannot be processed within the USB function, the EP0OTS flag is set. Rev. 3.00 Mar 17, 2006 page 123 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 0 EP0OTF Description 0 Endpoint 0 is in host output transfer standby state (Initial value) [Clearing conditions] 1 • When 0 is written to EP0OTF after reading EP0OTF = 1 • When endpoint 0 receives a SETUP token Endpoint 0 host output transfer (OUT transaction or SETUP transaction) has ended abnormally [Setting conditions] 7.2.11 • Transfer not possible due to FIFO full condition after OUT token reception (NAK transmission) • Data transfer not possible because EP0OTC = 0 after OUT token reception (NAK transmission) • Communication error after OUT token reception • When command received after SETUP token reception can be processed within the USB function USB Control/Status Register 0 (USBCSR0) Bit 7 6 5 4 3 DP5CNCT DP4CNCT DP3CNCT DP2CNCT EP0STOP 2 1 0 EPIVLD EP0OTC CKSTOP Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/W R/W R/W R/W USBCSR0 contains flags that indicate the USB hubs’ downstream port connection status, and bits that control the operation of the USB function. USBCSR0 is initialized to H'00 by a system reset, and bits 3 to 0 are also cleared to 0 by a function soft reset. Rev. 3.00 Mar 17, 2006 page 124 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bits 7 to 4—Downstream Port Connect 5 to 2 (DP5CNCT, DP4CNCT, DP3CNCT, DP2CNCT): Read-only status flags that indicate the connection status of the USB hubs’ external downstream ports. Bits 7 to 4 DP5CNCT to DP2CNCT Description 0 Cable is not connected to downstream port (Initial value) [Clearing conditions] • System reset • Downstream port disconnect • USB hub upstream port disconnect (Total downstream disconnect by software in reconnect process) 1 Cable is connected to downstream port, and power is being supplied [Setting condition] Downstream port connect Bit 3—Endpoint 0 Stop (EP0STOP): Bit that protects the contents of the USB function endpoint 0 FIFO. Setting EP0STOP to 1 enables the data transferred to the EP0 OUT-FIFO by a SETUP transaction to be protected. Bit 3 EP0STOP Description 0 EP0 OUT-FIFO, IN-FIFO operational (Initial value) [Clearing conditions] 1 • System reset • Function soft reset EP0 OUT-FIFO reading stopped • FVSR0O contents are not changed by an EPDR0O read EP0 IN-FIFO writing and transfer stopped • FIFO contents are not changed by an EPDR0I write • FVSR0I contents are not changed by setting EP0ITE Rev. 3.00 Mar 17, 2006 page 125 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 2—Endpoint Information Valid (EPIVLD): This bit makes the USB function block operational. Part of the process that makes the USB function block operational includes an endpoint information setting. After a system reset or function soft reset, the USB function block does not have any endpoint information. Endpoint information for the USB function in the H8/3567U and H8/3564U (see section 7.3.9, USB Module Startup Sequence) can be set by sequential writes to EPDR0I. When all the data has been written, the written endpoint information is made valid by setting the EPIVLD bit to 1. Writing 0 to the EPIVLD bit has no effect. Bit 2 EPIVLD Description 0 Endpoint information (EPINFO) has not been set (Initial value) [Clearing conditions] 1 • System reset • Function soft reset Endpoint information (EPINFO) has been set Bit 1—Endpoint 0O Transfer Control (EP0OTC): Controls USB function endpoint 0 control transfer. Clearing EP0OTC to 0 disables writes to the EP0 OUT-FIFO. A change of data transfer direction within a control transfer can be reported by means of the transfer fail interrupt caused by this action. In control transfer, a command is received in the SETUP transaction (command stage), then data transfer is performed in an OUT or IN transaction (data stage), and finally a transfer equivalent to a handshake is carried out in an IN or OUT transaction (status stage). When a SETUP token is received, EP0OTC is set to 1, FVSR is initialized, and command data can be received. On completion of command data reception, EP0OTC is cleared to 0 and the contents of the EP0O-FIFO are protected. If the command cannot be processed automatically by the USB function core, the EP0OTS flag is set and the slave CPU must decode the command. If command decoding shows that an OUT transaction will follow as the data stage, the slave CPU must set EP0OTC to 1 in preparation for an OUT transaction. If the command stage is followed by an IN transaction data stage, the slave CPU leaves EP0OTC cleared to 0. When the host CPU begins an OUT transaction as the status stage, the EP0OTF flag is set and a transfer fail interrupt is generated, enabling the slave CPU to recognize the end of the data stage. In response to this interrupt, the slave CPU sets EP0OTC to 1 and receives retransferred status stage data. Rev. 3.00 Mar 17, 2006 page 126 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 1 EP0OTC Description 0 EP0 OUT-FIFO writing stopped • (Initial value) Subsequent writes to EP0 OUT-FIFO are invalid [Clearing conditions] 1 • System reset • Function soft reset • Command data reception in SETUP transaction (EP0OTS flag setting) EP0 OUT-FIFO operational [Setting conditions] • SETUP token reception • When 1 is written to EP0OTC after reading EP0OTC = 0 Bit 0—Clock Stop (CKSTOP): Controls the USB function operating clock. When the USB function is placed in the suspend state due to a bus idle condition, this bit should be set to 1 after the necessary processing is completed. The clock supply to the USB function is then stopped, reducing power consumption. When the CKSTOP bit is set to 1, writes to USB module registers are invalid. If these registers are read, the contents of the read data are not guaranteed, but there are no read-related status changes (such as decrementing of FVSR). If a bus idle condition of the specified duration or longer is detected, the suspend IN interrupt flag is set, and when a change in the bus status is subsequently detected the suspend OUT interrupt flag is set. When the suspend OUT interrupt flag is set, the CKSTOP bit is simultaneously cleared to 0. Rev. 3.00 Mar 17, 2006 page 127 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 0 CKSTOP Description 0 Clock is supplied to USB function (Initial value) [Clearing conditions] 1 • System reset • Function soft reset • Suspend OUT interrupt flag setting Clock supply to USB function is stopped [Setting condition] When 1 is written to CKSTOP after reading CKSTOP = 0 in the function suspend state 7.2.12 Endpoint Stall Register (EPSTLR) Bit 7 6 5 4 3 — — — — Initial value 0 0 0 0 0 Read/Write R R R R R/W 2 1 0 — EP0STL 0 0 0 R/W R R/W EP2STL EP1STL EPSTLR contains bits (EPSTL) that place the USB function endpoints in the stall state. When an EPSTL bit is set to 1, the corresponding endpoint sends a STALL handshake in reply to the start of a transaction through reception of a token from the host. When the USB function receives a SETUP token, the EP0STL bit is automatically cleared to 0. EPSTLR is initialized to H'00 by a system reset or a function soft reset. Bit 3—Endpoint 2 Stall (EP2STL): Places endpoint 2 in the stall state. Bit 3 EP2STL Description 0 Endpoint 2 is operational 1 Endpoint 2 is in stall state Rev. 3.00 Mar 17, 2006 page 128 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) Bit 2—Endpoint 1 Stall (EP1STL): Places endpoint 1 in the stall state. Bit 2 EP1STL Description 0 Endpoint 1 is operational 1 Endpoint 1 is in stall state (Initial value) Bit 0—Endpoint 0 Stall (EP0STL): Places endpoint 0 in the stall state. Writing 0 to the EP0STL bit has no effect. Bit 0 EP0STL Description 0 Endpoint 0 is operational (Initial value) [Clearing condition] When endpoint 0 receives a SETUP token 1 Endpoint 0 is in stall state [Setting condition] When 1 is written to EP0STL after reading EP0STL = 0 7.2.13 Endpoint Reset Register (EPRSTR) Bit Initial value Read/Write Note: * 7 6 5 4 — — — — 0 0 0 0 0 0 0 0 R R/(W)* R/(W)* R/(W)* R R R R 3 2 1 EP2RST EP1RST EP0IRST 0 — Only 1 can be written. EPRSTR contains control bits (EPRST) that reset the pointer of the FIFO for a USB function endpoint host input transfer. When an EPRST bit is set to 1, the corresponding FIFO valid size register (FVSR) is initialized. The EPRST bits can only be written with 1, and are always read as 0. Rev. 3.00 Mar 17, 2006 page 129 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 3—Endpoint 2 Reset (EP2RST): Initializes the endpoint 2 FIFO. Bit 3 EP2RST Description 0 Normal read value (1) [1 write] (Initial value) EP2DIR = 0: FVSR2 is initialized to H'0000 EP2DIR = 1: FVSR2 is initialized to H'0010 Bit 2—Endpoint 1 Reset (EP1RST): Initializes the endpoint 1 FIFO. Bit 2 EP1RST Description 0 Normal read value (1) [1 write] (Initial value) EP1 FIFO size = 16 bytes: FVSR1 is initialized to H'0010 EP1 FIFO size = 32 bytes: FVSR1 is initialized to H'0020 Bit 1—Endpoint 0I Reset (EP0IRST): Initializes the endpoint 0I FIFO. Bit 1 EP0IRST Description 0 Normal read value (1) [1 write] FVSR0I is initialized to H'0010 Rev. 3.00 Mar 17, 2006 page 130 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) 7.2.14 Device Resume Register (DEVRSMR) Bit 7 6 5 4 3 2 1 0 — — — — — — — DVR Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R/(W)* Note: Only 1 can be written. * DEVRSMR contains a bit (DVR) that control remote wakeup of the USB function suspend state. When 1 is written to the DVR bit, the suspend state is cleared. The DVR bit can only be written with 1, and is always read as 0. 1 can be written to the DVR bit even if the CKSTOP bit is set to 1 in USBCSR0. Bit 0—Device Resume (DVR): Clears the suspend state. Bit 0 DVR Description 0 Normal read value (1) [1 write] (Initial value) Suspend state is cleared (remote wakeup) 7.2.15 Interrupt Source Select Register 0 (INTSELR0) Bit 7 6 5 4 3 2 1 0 TSELB EPIBS2 EPIBS1 EPIBS0 TSELC EPICS2 EPICS1 EPICS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W INTSELR0 contains bits that select the USB function USBIB and USBIC interrupt sources. INTSELR0 is initialized to H'00 by a system reset or a function soft reset. Rev. 3.00 Mar 17, 2006 page 131 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 7—Transfer Select B (TSELB): Together with bits EPIBS2 to EPIBS0, selects USBIB interrupt source. Bit 7 TSELB Description 0 USBIB interrupt is requested by a TS interrupt; the endpoint constituting the TS interrupt source is specified by bits EPIBS2 to EPIBS0 (Initial value) 1 USBIB interrupt is requested by a TF interrupt; the endpoint constituting the TF interrupt source is specified by bits EPIBS2 to EPIBS0 Bits 6 to 4—Interrupt B Endpoint Select 2 to 0 (EPIBS2 to EPIBS0): Together with the TSELB bit, these bits select USBIB interrupt source. Bit 6 Bit 5 Bit 4 EPIBS2 EPIBS1 EPIBS0 Description 0 0 0 Endpoint not selected 1 1 — 1 Endpoint 1 selected 0 Endpoint 2 selected 1 Setting prohibited — Setting prohibited (Initial value) Bit 3—Transfer Select C (TSELC): Together with bits EPICS2 to EPICS0, selects USBIC interrupt source. Bit 3 TSELC Description 0 USBIC interrupt is requested by a TS interrupt; the endpoint constituting the TS interrupt source is specified by bits EPICS2 to EPICS0 (Initial value) 1 USBIC interrupt is requested by a TF interrupt; the endpoint constituting the TF interrupt source is specified by bits EPICS2 to EPICS0 Rev. 3.00 Mar 17, 2006 page 132 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bits 2 to 0—Interrupt C Endpoint Select 2 to 0 (EPICS2 to EPICS0): Together with the TSELC bit, these bits select USBIC interrupt source. Bit 2 Bit 1 Bit 0 EPICS2 EPICS1 EPICS0 Description 0 0 0 Endpoint not selected 1 Endpoint 1 selected 0 Endpoint 2 selected 1 Setting prohibited — Setting prohibited 1 1 7.2.16 — (Initial value) Interrupt Source Select Register 1 (INTSELR1) Bit 7 6 5 4 3 2 1 0 — — — — — — DTCBE DTCCE Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R/W R/W Register INTSELR1 is not used in this model. Do not write 1 to the bits in INTSELR1. 7.2.17 Hub Overcurrent Control Register (HOCCR) Bit 7 6 5 4 3 2 1 0 — — PCSP OCDSP HOC5E HOC4E HOC3E HOC2E Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W The USB hub downstream ports are connected to the USB connector as data (D+/D–). The power supply (VBUS) connected to the USB connector is generated by connecting a power supply control IC externally. HOCCR contains bits that control the power supply control IC control input/output. HOCCR is initialized to H'00 by a system reset. Rev. 3.00 Mar 17, 2006 page 133 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 5—Power Supply Enable Control Polarity (PCSP): This bit is set according to the polarity of the power supply control IC output enable inputs. The power supply control IC output enable inputs are connected to H8 pins ENP5 to ENP2. Bit 5 PCSP Description 0 Power supply control IC requires low-level input for enabling 1 Power supply control IC requires high-level input for enabling (Initial value) Bit 4—Overcurrent Detection Polarity (OCDSP): This bit is set according to the polarity of the power supply control IC overcurrent detection outputs. The power supply control IC overcurrent detection outputs are connected to H8 pins OCP5 to OCP2. Bit 4 OCDSP Description 0 Power supply control IC outputs low level in case of overcurrent detection (Initial value) 1 Power supply control IC outputs high level in case of overcurrent detection Bits 3 to 0—Overcurrent Detection Control Enable 5 to 2 (HOC5E to HOC2E): These pins select whether or not power supply control IC control is performed for each USB hub downstream port. If any of the four downstream ports are not used, the corresponding D+/D- pins should be pulled down as specified. Leave the corresponding HOCE bit cleared to 0, disabling the corresponding output enable pin and overcurrent detection pin. Disabled pins can be used as general port pins (port C). Bit 3 HOC5E Description 0 Pins ENP5 and OCP5 are general ports (PC7, PC3) 1 Pins ENP5 and OCP5 have output enable and overcurrent detection functions Rev. 3.00 Mar 17, 2006 page 134 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) Bit 2 HOC4E Description 0 Pins ENP4 and OCP4 are general ports (PC6, PC2) 1 Pins ENP4 and OCP4 have output enable and overcurrent detection functions (Initial value) Bit 1 HOC3E Description 0 Pins ENP3 and OCP3 are general ports (PC5, PC1) 1 Pins ENP3 and OCP3 have output enable and overcurrent detection functions (Initial value) Bit 0 HOC2E Description 0 Pins ENP2 and OCP2 are general ports (PC4, PC0) 1 Pins ENP2 and OCP2 have output enable and overcurrent detection functions 7.2.18 (Initial value) USB Control Register (USBCR) Bit 7 6 FADSEL FONLY 5 4 3 2 1 0 FNCSTP UIFRST HPLLRST HSRST FPLLRST FSRST Initial value 0 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W USBCR contains bits (FADSEL, FONLY, FNCSTP) that control USB function and USB hub internal connection, and reset control bits for sequential enabling of the operation of each part according to the USB module start-up sequence. USBCR is initialized to H'7F by a system reset [in an H8/3567U and H8/3564U reset (by RES input or the watchdog timer), and in hardware standby mode]. It is not initialized in software standby mode. Rev. 3.00 Mar 17, 2006 page 135 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 7—USB Function I/O Analog/Digital Select (FADSEL): Selects the USB function data input/output method when the FONLY bit is set to 1 so that the USB hub block is disabled and only the USB function block operates. Bit 7 FADSEL Description 0 USD+ and USD– pins are used for USB function block data input/output (Initial value) 1 USB function block data input/output is implemented by multiplexing Philips transceiver/receiver (PDIUSB11A) compatible control input/output with port C pins Port C Philips PDIUSB11A PC7 Input VP Differential input (+) PC6 Input VM Differential input (–) PC5 Input RCV Data input PC4 Output VPO Differential output (+) PC3 Output VMO Differential output (–) PC2 Output OE Output enable PC1 Output SUSPEND Suspend setting PC0 Output SPEED Speed setting High level fixed output for 12 Mbps specification Bit 6—USB Function Select (FONLY): Selects enabling/disabling of the USB hub block. When the USB hub block is enabled, the USB function block is connected internally to USB hub downstream port 1. When the USB hub block is disabled, the USB function block is directly connected to the upstream port, and the USB operating clock selected/divided/multiplied in accordance with UPLLCR settings is not supplied to the USB hub block. Bit 6 FONLY Description 0 USB function block is connected internally to USB hub downstream port 1 USB hub block is enabled 1 USB function block is directly connected to upstream port USB hub block is disabled Rev. 3.00 Mar 17, 2006 page 136 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) Bit 5—USB Function Stop/Suspend (FNCSTP): With the H8/3567U and H8/3564U, it is possible to disconnect the USB function block from the USB hub block’s downstream port 1, and set a power-down state in which the USB operating clock supply is halted. Register accesses by the CPU are still possible in this state. The FNCSTP bit is used when disconnecting the USB function block and switching the microcomputer block to power-down mode when the system’s power supply is cut, or when reconnecting the USB function block when recovering from power-down mode or in the event of a power-on reset. When the FNCSTP bit is set to 1, the USB operating clock selected/divided/multiplied in accordance with UPLLCR settings is not supplied to the USB function block. Bit 5 FNCSTP Description 0 For USB function block, USB hub downstream port 1 internal connection is set to connected state 1 For USB function block, USB hub downstream port 1 internal connection is set to disconnected state, and power-down state is set (Initial value) Bit 4—USB Interface Soft reset (UIFRST): Resets the EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 registers. When UIFRST is set to 1, the EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 registers are initialized. Bit 4 UIFRST Description 0 EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 are placed in operational state 1 EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 are placed in reset state (Initial value) Rev. 3.00 Mar 17, 2006 page 137 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Bit 3—Hub Block PLL Soft reset (HPLLRST): Resets the USB bus clock circuit (DPLL) in the hub. When HPLLRST is set to 1, the DPLL circuit in the hub is reset, and bus clock synchronous operation halts. HPLLRST is cleared to 0 after PLL operation stabilizes. Bit 3 HPLLRST Description 0 Hub DPLL is placed in operational state 1 Hub DPLL is placed in reset state (Initial value) Bit 2—Hub Block Internal State Soft reset (HSRST): Resets the internal state of the USB hub block. When HSRST is set to 1, the internal state of the USB hub block, excluding the internal USB bus clock circuit (DPLL), is initialized. HSRST is cleared to 0 after DPLL operation stabilizes. Bit 2 HSRST Description 0 Internal state of USB hub block is set to operational state 1 Internal state of USB hub block is set to reset state (excluding DPLL) (Initial value) Bit 1—Function Block PLL Soft reset (FPLLRST): Resets the USB bus clock circuit (DPLL) in the function. When FPLLRST is set to 1, the DPLL circuit in the function is reset, and bus clock synchronous operation halts. FPLLRST is cleared to 0 after PLL operation stabilizes. Bit 1 FPLLRST Description 0 Function DPLL is placed in operational state 1 Function DPLL is placed in reset state Rev. 3.00 Mar 17, 2006 page 138 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) Bit 0—Function Block Internal State Reset (FSRST): Resets the internal state of the USB function block. When FSRST is set to 1, the internal state of the USB function block, excluding the internal bus clock circuit (DPLL), is initialized. FSRST is cleared to 0 after DPLL operation stabilizes. The state in which FSRST = 1 and UIFRST = 1 is called a function soft reset. Bit 0 FSRST Description 0 Internal state of USB function block is set to operational state 1 Internal state of USB function block is set to reset state (excluding DPLL) (Initial value) 7.2.19 USB PLL Control Register (UPLLCR) Bit 7 6 5 — — — 4 3 2 1 Initial value 0 0 0 0 0 0 0 1 Read/Write R R R R/W R/W R/W R/W R/W CKSEL2 CKSEL1 CKSEL0 PFSEL1 0 PFSEL0 UPLLCR contains bits that control the method of generating the USB function and USB hub operating clock. UPLLCR is initialized to H'01 by a system reset [in an H8/3567U and H8/3564U reset (by RES input or the watchdog timer), and in hardware standby mode]. It is not initialized in software standby mode. Bits 4 to 2—Clock Source Select 2 to 0 (CKSEL2 to CKSEL0): These bits select the source of the clock supplied to the USB operating clock generator (PLL). CKSEL0 selects either the USB clock pulse generator (XTAL12) or the system clock pulse generator (XTATL) as as the clock source. When selected as a clock source, the USB clock pulse generator starts operating. It operates with CKSEL2=1, CKSEL0=1. When CKSEL2 = 1 and CKSEL1 = 1, the PLL operates. When CKSEL1 is cleared to 0, a clock is not input to the PLL, and PLL operation halts. The 48 MHz signal from the USB clock pulse generator can be input directly as the USB operating clock. Rev. 3.00 Mar 17, 2006 page 139 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) When CKSEL2 is cleared to 0, a clock is not input to the PLL, and PLL operation halts. Bit 4 Bit 3 Bit 2 CKSEL2 CKSEL1 CKSEL0 0 1 Description 0 0 PLL operation halted, clock input halted — — PLL operation halted, clock input halted 0 0 Setting prohibited 1 PLL operation halted (Initial value) USB clock pulse generator (XTAL12: 48 MHz) used directly instead of PLL output 1 0 PLL operates with system clock pulse generator (XTAL) as clock source 1 PLL operates with USB clock pulse generator (XTAL12) as clock source Bits 1 and 0—PLL Frequency Select 1 and 0 (PFSEL1, PFSEL0): These bits select the frequency of the clock supplied to the USB operating clock pulse generator (PLL). The PLL generates the 48 MHz USB operating clock using the frequency selected with these bits as the clock source frequency. Bit 1 Bit 0 PFSEL1 PFSEL0 Description 0 0 PLL input clock is 8 MHz 1 PLL input clock is 12 MHz 0 PLL input clock is 16 MHz 1 PLL input clock is 20 MHz 1 Rev. 3.00 Mar 17, 2006 page 140 of 706 REJ09B0303-0300 (Initial value) Section 7 Universal Serial Bus Interface (USB) 7.2.20 USB Port Control Register (UPRTCR) Bit 7 6 5 4 3 2 1 0 — — Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W DSPSEL2 DSPSEL1 DSPSEL0 PCNMD2 PCNMD1 PCNMD0 UPRTCR is a test register. Its initial settings should not be changed. UPRTCR is initialized to H'00 by a system reset (reset of this LSI by a RES input or by the watchdog timer, and in hardware standby mode). It is not initialized in software standby mode. Bits 5 to 3—Downstream Port Select 2 to 0 (DSPSEL2 to DSPSEL0): These bits select the downstream port to be tested. Bit 5 Bit 4 Bit 3 DSPSEL2 DSPSEL1 DSPSEL0 Description 0 0 0 Downstream port 2 selected 1 Downstream port 3 selected 1 0 Downstream port 4 selected 1 Downstream port 5 selected — Downstream port 1 selected 1 — (Initial value) Bits 2 to 0—Port Connection Mode Select 2 to 0 (PCNMD2 to PCNMD0): These bits set ports C and D to the normal operating mode or a test operating mode. The PCNMD bits must be set to B'000. Bit 2 Bit 1 Bit 0 PCNMD2 PCNMD1 PCNMD0 Description 0 0 0 User mode 1 Digital upstream mode 1 0 Digital downstream mode 1 Digital upstream/downstream mode 0 Upstream transceiver/receiver monitor mode 1 Downstream transceiver/receiver monitor mode — Reserved 1 0 1 (Initial value) Rev. 3.00 Mar 17, 2006 page 141 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.2.21 USB Test Registers 2, 1, 0 (UTESTR2, UTESTR1, UTESTR0) UTESTR2, UTESTR1, and UTESTR0 are test registers. Their initial settings should not be changed. UTESTR1 and UTESTR0 are initialized to H'00 by a system reset [in an H8/3567U or H8/3564U reset (by RES input or the watchdog timer), and in standby mode]. They are not initialized in software standby mode. UTESTR2 is initialized to H'FF by a system reset [in an H8/3567U or H8/3564U reset (by RES input or the watchdog timer), and in standby mode]. It is not initialized in software standby mode. UTESTR0 Bit 7 6 5 4 3 2 1 0 TEST15 TEST14 TEST13 TEST12 TEST11 TEST10 TEST9 TEST8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 TEST7 TEST6 TEST5 TEST4 TEST3 TEST2 TEST1 TEST0 UTESTR1 Bit Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W UTESTR2 Bit 7 6 5 4 3 2 1 0 TESTA TESTB TESTC TESTD TESTE TESTF TESTG TESTH Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 142 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.2.22 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers that perform module stop mode control. When the MSTP1 bit is set to 1, the USB module stops operating and enters module stop mode at the end of the bus cycle. However, when USB clocks (XTAL12, EXTAL12) are selected as USB operating clocks, the USB module does not stop operating. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRL Bit 1—Module Stop (MSTP1): Specifies module stop mode for the USB module. MSTPCRL Bit 1 MSTP1 Description 0 USB module stop mode cleared 1 USB module stop mode set 7.2.23 (Initial value) Serial Timer Control Register (STCR) Bit 7 6 5 4 3 2 1 0 — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W STCR is an 8-bit readable/writable register that controls register access, the IIC operating mode, selects the TCNT input clock and controls USB. For details of functions other than register access control, see the descriptions of the relevant modules. If a module controlled by STCR is not used, do not write 1 to the corresponding bit. Rev. 3.00 Mar 17, 2006 page 143 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) STCR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—Reserved: Do not write 1 to this bit. 2 2 Bits 6 and 5—I C Control (IICX1, IICX0): These bits control the operation of the I C bus 2 interface. For details, see section 16, I C Bus Interface. 2 2 Bit 4—I C Master Enable (IICE): Controls CPU access to the I C bus interface data registers and control registers (ICCR, ICSR, ICDR/SARX, and ICMR/SAR), the PWMX data registers and control registers (DADRAH/DACR, DADRAL, DADRBH/DACNTH, and DADRBL/DACNTL), and the SCI control registers (SMR, BRR, and SCMR). Bit 4 IICE Description 0 Addresses H'FFD8 and H'FFD9, and H'FFDE and H'FFDF, are used for SCI0 control register access (Initial value) 1 Addresses H'FF88 and H'FF89, and H'FF8E and H'FF8F, are used for IIC1 data register and control register access Addresses H'FFA0 and H'FFA1, and H'FFA6 and H'FFA7, are used for PWMX data register and control register access Addresses H'FFD8 and H'FFD9, and H'FFDE and H'FFDF, are used for IIC0 data register and control register access Bit 3—Reserved: Do not write 1 to this bit. Bit 2—USB enable (USBE): This bit controls CPU access to the USB data register and control register. Bit 2 USBE Description 0 Prohibition of the above register access 1 Permission of the above register access (Initial value) Bits 1 and 0—Internal Clock Source Select 1 and 0 (ICKS1, ICKS0): These bits, together with bits CKS2 to CKS0 in TCR, select the clock to be input to TCNT. For details, see section 12, 8-Bit Timers. Rev. 3.00 Mar 17, 2006 page 144 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.3 Operation USB is an interface for peripherals of the personal computers standardized by Intel and others and the standard is defined by the USB Specification. Operation of the USB hubs and USB function in this model is based on the definitions of the USB Specification. This section gives only a brief overview of the USB bus specifications, and focuses on operations by the slave CPU. 7.3.1 USB Compound Device Configuration A USB compound device is a USB device incorporating USB hubs and a USB function. The H8/3567U and H8/3564U incorporate a compound device with a configuration in which the USB function is internally connected to one downstream port of a USB hub with five downstream ports. With a USB compound device, it is usual for the USB function to be constantly connected to the USB hub. With the H8/3567U and H8/3564U, however, the internally connected USB function is not constantly connected to the USB hub. After release from an H8 reset, the USB function can be connected or disconnected under program control. Therefore, the device is not identified as a compound device in the hub descriptor wHub Characteristics. There are two power feed modes for a USB device: bus feed and self-feed. The H8/3567 Group use the self-feed method. With the H8/3567U and H8/3564U a setting can be made to disconnect the USB function block and operate the USB hub block alone. In this case, it is possible to place the slave CPU in software standby mode, and operate it in power-down mode. 7.3.2 Functions of USB Hub Block The USB hub block implements the functions described in section 11 of the USB Specification. There are five downstream ports; downstream port 1 can be connected to the USB function block internally, while downstream ports 2 to 5 are connected to external pins. Downstream ports 2 to 5 have their respective overcurrent detection pins (OCP2 to OCP5) and power supply output enable pins (ENP2 to ENP5), making it is possible to control enabling/disabling of the power supply control IC connected to the VBUS, and report overcurrent detection to the host, on an individual port basis. As exchanges with the USB host are all executed automatically within the USB hub, USB hub block exchanges with the slave CPU are limited to the following cases: Rev. 3.00 Mar 17, 2006 page 145 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 1. USB module reset or operation halt a. Slave CPU system reset (Internal reset by RES or STBY input, or WDT0) b. Module stop condition initiated by slave CPU (USB module stopped by means of MSTPCR) c. USB module reset by means of HPLLRST or HSRST bit in USBCR 2. Downstream port overcurrent detection and power supply output enable control a. Overcurrent detection and power supply output enable for individual ports by bits HOC5E to HOC2E in HOCCR. (When a downstream port itself is not used, DSD+/DSD- pins require pullup/pulldown as specified.) 7.3.3 Functions of USB Function The USB function block has three endpoints. By using a combination of endpoint 2 enabling/disabling and IN/OUT mode with endpoint 1 MaxPacketSize, the three alternates shown below can be selected for the USB function block. Twice the MaxPacketSize value is set for the number of FIFO bytes. As the command that selects the alternate is a USB standard command, it is not possible to notify the slave CPU of the alternate selected. It is therefore necessary to ensure that the selected alternate is the same for the H8 firmware and the host CPU device driver. Endpoint 0 Endpoint 1 Endpoint 2 Configuration Interface Alternate IN/OUT FIFO IN/OUT FIFO IN/OUT FIFO 1 0 0 IN/OUT 16 bytes each IN 16 bytes IN 16 bytes 1 IN/OUT 16 bytes each IN 16 bytes OUT 16 bytes 2 IN/OUT 16 bytes each IN 32 bytes None None The USB function supports control transfer by means of endpoint 0 and input transfer by means of endpoints 1 and 2. A control transfer consists of a number of transactions. The command transmitted from the host in the SETUP transaction is first decoded by the USB function core. Rev. 3.00 Mar 17, 2006 page 146 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) When a SETUP token is received, FVSR is initialized and EP0OTC is set to 1, and command reception is enabled. If the received command is a USB standard command (other than GetDescriptor or SetDescriptor), the EP0OTF flag is set and the slave CPU is notified of the fact that a USB standard command has been received. In this case, the remaining transactions in the control transfer are processed within the USB function without intervention by the slave CPU. If the received command is a GetDescriptor or SetDescriptor command, or a command specific to a device class, the EP0OTS flag is set. The slave CPU must read the command from the FIFO, then decode and execute it. The remaining transactions in the control transfer must also be processed by the slave CPU using the FIFO, etc. Input transfers consist of individual IN or OUT transactions. These must all be processed by the slave CPU using the FIFO, etc. When processing by the slave CPU is necessary as described above, the communication processing load is shared between the USB function and the slave CPU. The roles of the USB function and the slave CPU, and the flag and bits used in the interface, are shown in table 7.3. Table 7.3 Role Sharing between USB Function and Slave CPU Item/Description 1 D+/D– signal analog ↔ digital conversion Operating Hardware Related Registers/ Flags/Bits Port block — USB function core 2 Serial ↔ parallel conversion/bit stuffing USB function core SOFF SETUPF PID determination/addition, CRC determination/addition 3 Token packet determination/notifying slave CPU of SETUP USB function core 4 Handshake packet determination/generation USB function core DAT0/1 PID toggling, FIFO rewinding, ACK/NAK detection/return FVSR, EPTE ACK handshake detection and slave CPU notification/ACK handshake return TS, EPTS Data error detection and slave CPU notification/NAK handshake return TF, EPTF STALL handshake return EPSTL 5 Data packet reception/regeneration/transfer to slave CPU USB function core FIFO 6 USB command decoding and execution USB function core FIFO Slave CPU Rev. 3.00 Mar 17, 2006 page 147 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Processing of electrical signals on the USB bus line and processing of signal bit streams is performed by the bus driver/receiver in the port block and the USB function core block. The token/acknowledgment type and data bytes are extracted and, conversely, acknowledgment and data bytes are converted to bit stream electrical signals (items 1 and 2). When a SETUP token is received, if a GetDescriptor or SetDescriptor command, or a command specific to a device class, is received, the EP0OTS flag is set and the slave CPU is notified (item 3). The command itself is transferred using the FIFO, and must be decoded and executed by the slave CPU (item 6). The remaining transactions in the control transfer must also be processed by the slave CPU using the FIFO, etc. (items 4 and 5). Reception of an IN or OUT token in control transfer or interrupt transfer is not reported to the CPU, and the operation continues with data transfer. In the case of an IN transaction, the transmit data is prepared in the FIFO beforehand, and if the EPTE bit is set transmission is started, or if not, a NAK handshake is performed. When an IN transaction ends, normal or abnormal termination of the transfer is confirmed by means of the host handshake, and is reported to the slave CPU by means of TS/TF/EPTS/EPTF. In the case of an OUT transaction, an ACK handshake is performed when all the data has been received in the FIFO, or a NAK handshake if it was not possible to receive all the data. With both IN transactions and OUT transactions, a STALL handshake is performed if the endpoint is placed in the stall state by means of EPSTL. 7.3.4 Operation when SETUP Token Is Received (Endpoint 0) The group of transactions initiated when the host issues a SETUP token is called a control transfer. A control transfer consists of three stages: setup, data, and status. Control transfers are of two kinds: control write transfers and control read transfers. The type of transfer (read or write) and the number of transfer bytes in the data stage are determined by the 8-byte command transferred OUT in the setup stage. The setup stage consists of a setup transaction, the data stage may have no transaction or one or more data transactions, and the status stage consists of a single data transaction. The packets contained in each transaction are shown in the table 7.4. Rev. 3.00 Mar 17, 2006 page 148 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Table 7.4 Packets in Each Transaction Stage Token Phase Data Phase Handshake Phase* Setup stage SETUP token packet OUT data packet (8 bytes) (host → slave) ACK handshake packet (slave → host) Data stage OUT token packet OUT data packet (host → slave) ACK/NAK/STALL handshake packet (slave → host) Status stage IN token packet IN data packet 2 (0 bytes)* (slave → host) ACK handshake packet (host → slave) NAK/STALL handshake packet (slave → host) — IN data packet (slave → host) ACK handshake packet (host → slave) NAK/STALL handshake packet (slave → host) — OUT token packet OUT data packet (host → slave) ACK/NAK/STALL handshake packet (slave → host) IN token packet IN data packet 2 (0 bytes)* (slave → host) ACK handshake packet (host → slave) NAK/STALL handshake packet (slave → host) — Control write transfer Control read transfer Data stage Status stage No data stage Status stage IN token packet 1 Notes: 1. This phase is present only if a data packet transfer was executed in the data phase. 2. When all the data in the FIFO has been transferred and the FIFO is empty, the EPTE bit is cleared to 0. If an IN transaction is then started, a NAK handshake is returned. A 0-byte data packet is transferred by setting the EPTE bit to 1 when the FIFO is empty. Figure 7.2 shows the operation of the USB function core and the H8 firmware when the USB function receives a SETUP token (setup transaction). For other cases, see section 7.3.5, Operation when OUT Token Is Received, and section 7.3.6, Operation when IN Token Is Received. Rev. 3.00 Mar 17, 2006 page 149 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core SETUP token packet output SETUP token packet reception OUT data packet (8 bytes) output ACK handshake packet reception OUT data packet (8 bytes) reception Core interface Slave CPU Automatic setting of various flags*1 USBIA (SETUP) interrupt request Start of USBIA interrupt handling Data write to EP0O FIFO Read USBIFR*2 Command data decoding Determination of necessity of decoding by slave CPU Record in user memory etc. that this is state in which decoding is performed by EP0OTS interrupt occurring next ACK transmission to host Clear SETUPF bit to 0 in USBIFR NAK transmission to slave CPU FVSR0O not updated End of USBIA interrupt handling USBID (EP0OTF) interrupt request Start of USBID interrupt handling Read USBIFR Confirm TF interrupt Read TFFR Confirm EP0OTF interrupt Confirm that command decoding by slave CPU is not necessary, and amend record in user memory, etc. Clear EP0OTF bit to 0 in TFFR End of USBID interrupt handling Notes: 1. Bit EP0OTC set to 1 in USBCSR0, FVSR0I and FVSR0O initialized, bits EP0ITS and EP0OTS cleared to 0 in TSFR, bits EP0ITF and EP0OTF cleared to 0 in TFFR, bit EP0STL cleared to 0 in EPSTLR. 2. As the USBIA interrupt is assigned only to the SETUP interrupt, there is no need for processing to determine the interrupt source. Figure 7.2 (1) Operation when SETUP Token Is Received (Decoding by Slave CPU Not Required) Rev. 3.00 Mar 17, 2006 page 150 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core Core interface SETUP token packet output SETUP token packet reception Automatic setting of various flags*1 OUT data packet (8 bytes) output ACK handshake packet reception OUT data packet (8 bytes) reception Slave CPU USBIA (SETUP) interrupt request Start of USBIA interrupt handling Data write to EP0O FIFO Read USBIFR*2 Command data decoding Determination of necessity of decoding by slave CPU Record in user memory etc. that this is state in which decoding is performed by EP0OTS interrupt occurring next ACK transmission to host Clear SETUPF bit to 0 in USBIFR ACK transmission to slave CPU Update FVSR0O End of USBIA interrupt handling Clear EP0OTC bit to 0 in USBCSR0 USBID (EP0OTS) interrupt request Start of USBID interrupt handling Read USBIFR Confirm TS interrupt Read TSFR Confirm EP0OTS interrupt Decode execution determined from record status in user memory, etc. Continued on next page Notes: 1. Bit EP0OTC set to 1 in USBCSR0, FVSR0I and FVSR0O initialized, bits EP0ITS and EP0OTS cleared to 0 in TSFR, bits EP0ITF and EP0OTF cleared to 0 in TFFR, bit EP0STL cleared to 0 in EPSTLR. 2. As the USBIA interrupt is assigned only to the SETUP interrupt, there is no need for processing to determine the interrupt source. Figure 7.2 (2) Operation when SETUP Token Is Received (Decoding by Slave CPU Required) Rev. 3.00 Mar 17, 2006 page 151 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core Core interface Slave CPU Continued from previous page Read FVSR0O Confirm presence of 8 bytes of data in EP0O FIFO Update FVSR0O Read 8 bytes of data in EP0O FIFO from EPDR0O Determine instruction by data decoding If instruction is Control-OUT, set EP0OTC bit to 1 in USBCSR0 (write 1 after reading 0) Clear EP0OTS bit to 0 in TSFR End of USBID interrupt handling Figure 7.2 (2) Operation when SETUP Token Is Received (Decoding by Slave CPU Required) (cont) Rev. 3.00 Mar 17, 2006 page 152 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.3.5 Operation when OUT Token Is Received (Endpoints 0 and 2) Figure 7.3 shows the operation of the USB function core and the H8 firmware when the USB function receives an OUT token (OUT transaction). OUT transactions are used in the data stage and status stage of a control transfer, and in an input transfer. USB host USB function core OUT token packet output OUT token packet reception OUT data packet (8 bytes) output OUT data packet (8 bytes) reception ACK handshake packet reception ACK transmission to host ACK transmission to slave CPU Core interface Slave CPU Data write to EP2 FIFO Update FVSR2 USBID (EP2TS) interrupt request* Start of USBID interrupt handling Read USBIFR Confirm TS interrupt Read TSFR Confirm EP2TS interrupt Read FVSR2 Confirm amount of readable data (8 bytes) Update FVSR2 Read data (8 bytes) in EP2 FIFO from EPDR2 Clear EP2TS bit to 0 in TSFR End of USBID interrupt handling Note: * When the EP2TS interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.3 (1) Operation when OUT Token Is Received (EP2-OUT: Initial FIFO Empty) Rev. 3.00 Mar 17, 2006 page 153 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core OUT token packet output OUT token packet reception OUT data packet (8 bytes) output OUT data packet (8 bytes) reception NAK handshake packet reception NAK transmission to host NAK transmission to slave CPU Core interface Slave CPU Data write not possible because EP2 FIFO is full USBID (EP2TF) interrupt request*1 Start of USBID interrupt handling Read USBIFR Confirm TF interrupt Read TFFR Confirm EP2TF interrupt Read FVSR2 Confirm amount of readable data (16 bytes) Retransmission OUT token packet output OUT token packet reception Update FVSR2 Read data (16 bytes) in EP2 FIFO from EPDR2 OUT data packet (8 bytes) output OUT data packet (8 bytes) reception Data write to EP2 FIFO Clear EP2TF bit to 0 in TFFR ACK handshake packet reception ACK transmission to host ACK transmission to slave CPU End of USBID interrupt handling Update FVSR2 Continued on next page Note: 1. When the EP2TF interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.3 (2) Operation when OUT Token Is Received (EP2-OUT: Initial FIFO Full) Rev. 3.00 Mar 17, 2006 page 154 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core Core interface Slave CPU Continued from previous page USBID (EP2TS) interrupt request*2 Start of USBID interrupt handling Read USBIFR Confirm TS interrupt Read TSFR Confirm EP2TS interrupt Read FVSR2 Confirm amount of readable data (8 bytes) Update FVSR2 Read data (8 bytes) in EP2 FIFO from EPDR2 Clear EP2TS bit to 0 in TSFR End of USBID interrupt handling Note: 2. When the EP2TS interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.3 (2) Operation when OUT Token Is Received (EP2-OUT: Initial FIFO Full) (cont) 7.3.6 Operation when IN Token Is Received (Endpoints 0, 1, and 2) Figure 7.4 shows the operation of the USB function core and the H8 firmware when the USB function receives an IN token (IN transaction). IN transactions are used in the data stage and status stage of a control transfer, and in an input transfer. Rev. 3.00 Mar 17, 2006 page 155 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core IN token packet output IN token packet reception NAK handshake packet reception NAK transmission to host NAK transmission to slave CPU Core interface Slave CPU Data read not possible because EP2 FIFO is empty USBID (EP2TF) interrupt request*1 Start of USBID interrupt handling Read USBIFR Confirm TF interrupt Read TFFR Confirm EP2TF interrupt Read FVSR2 Confirm amount of data writable (16 bytes) Data write to EP2 FIFO Write amount of data writable in EP2 FIFO into EPDR2 Update FVSR2 Data transmission enabled Set EP2TE bit to 1 in PTTER Retransmission IN token packet output IN token packet reception IN data packet reception IN data packet transmission ACK handshake packet transmission ACK reception ACK transmission to slave CPU Data read from EP2 FIFO Clear EP2TF bit to 0 in TFFR End of USBID interrupt handling Update FVSR2 Continued on next page Note: 1. When the EP2TF interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.4 (1) Operation when IN Token Is Received (EP2-IN: Initial FIFO Empty) Rev. 3.00 Mar 17, 2006 page 156 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core Core interface Slave CPU Continued from previous page USBID (EP2TS) interrupt request*2 Start of USBID interrupt handling Read USBIFR Confirm TS interrupt Read TSFR Confirm EP2TS interrupt Read FVSR2 Confirm amount of data writable Data write to EP2 FIFO Update FVSR2 Data transmission enabled Write amount of data writable in EP2 FIFO into EPDR2 Set EP2TE bit to 1 in PTTER Clear EP2TSF bit to 0 in TSFR End of USBID interrupt handling Note: 2. When the EP2TS interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.4 (1) Operation when IN Token Is Received (EP2-IN: Initial FIFO Empty) (cont) Rev. 3.00 Mar 17, 2006 page 157 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) USB host USB function core IN token packet output IN token packet reception IN data packet (8 bytes) reception IN data packet (8 bytes) transmission ACK handshake packet transmission Core interface Slave CPU Data read from EP2 FIFO ACK reception ACK transmission to slave CPU Update FVSR2 USBID (EP2TS) interrupt request* Start of USBID interrupt handling Read USBIFR Confirm TS interrupt Read TSFR Confirm EP2TS interrupt Read FVSR2 Confirm amount of data writable (8 bytes) Data write to EP2 FIFO Write amount of data writable in EP2 FIFO into EPDR2 Update FVSR2 Data transmission enabled Set EP2TE bit to 1 in PTTER Clear EP2TS bit to 0 in TSFR End of USBID interrupt handling Note: * When the EP2TS interrupt is set for USBIB or USBIC by the INTSELR0 setting, that interrupt request is generated. When an USBIB or USBIC interrupt is generated, there is no need for processing to determine the interrupt source. (A register read is necessary in order to write 0 after reading 1.) Figure 7.4 (2) Operation when IN Token Is Received (EP2-IN: Initial FIFO Full) Rev. 3.00 Mar 17, 2006 page 158 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.3.7 Suspend/Resume Operations If the USB data line is idle for a period longer than that stipulated in the USB Specification, the H8/3567 Group’s USB hubs and USB function automatically enter the suspend state. The suspend state is automatically cleared (i.e. operation is resumed) when the upstream side (host) restarts data transmission, but operation can also be forcibly resumed by the USB function (remote wakeup). Changes in the suspend/resume state can be ascertained by means of the SPNDIF and SPNDOF flags. Remote wakeup is executed by setting the DVR bit. 7.3.8 USB Module Reset and Operation-Halted States A reset or operation-halted state can be set for the USB module by means of a number of control bits. For information on sequential setting of these bits when starting up the USB module, see section 7.3.9, USB Module Startup Sequence. There are several kinds of USB module reset and operation-halted state, as listed below. In the hardware standby and reset, the entire USB module is initialized. In the descriptions of individual bits in the register descriptions, this initialization condition is not indicated, and only “(Initial value)” is shown. 1. Hardware standby state 2. Reset state 3. Module stop state 4. Software standby state 5. USB function stop state 6. USB function only state 7. USB bus reset state 8. USB suspend state Hardware Standby State: When the H8/3567 Group’s STBY pin is driven low, the chip enters the hardware standby state. In the hardware standby state, all the H8/3567 Group’s initializable registers and internal states are initialized, and all H8/3567 Group pins go to the high-impedance state. XTAL-EXTAL system clock oscillation and XTAL12-EXTAL12 USB clock oscillation both halt. Reset State: When the H8/3567 Group’s RES pin is driven low, the chip enters the reset state. In the reset state, all the H8/3567 Group’s initializable registers and internal states are initialized, and all H8/3567 Group pins go to the input state. XTAL-EXTAL system clock oscillation is enabled. Rev. 3.00 Mar 17, 2006 page 159 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Module Stop State: When bit 1 of MSTPCR is set to 1, the USB module enters the module stop state. In the module stop state, supply of system clock to the USB module is stopped. However, when USB clocks (XTAL12, EXTAL12) are selected as USB operating clocks, the USB module does not stop the operation. When setting the USB module stop state, return the value of UPLLCR to the initial state. Also, it is recommended to return the value of USBCR to the initial state to prepare for cancellation of the module stop state. As bit 1 of MSTPCR is initialized to 1 by a transition to hardware standby mode or a reset, the USB module is in the module stop state after reset release. Software Standby State: When a SLEEP instruction is executed after setting the SSBY bit to 1 in SBYCR, the chip enters the software standby state. In the software standby state the USB module does not enter the reset or operation-halted state. However, since the USB function cannot fulfill its role when the slave CPU halts due to a transition to the software standby state, operation of the USB function must be halted before the software standby state setting is made. Set the FNCSTP bit to 1 in USBCR to disconnect the USB function from the bus (see USB Function Stop State below). In the software standby state, XTAL-EXTAL system clock oscillation halts. If the system clock has been set as the USB operating clock by means of the CKSEL bits in UPLLCR, the USB hubs cannot operate, either, since the clock is halted. If the USB clock (XTAL12-EXTAL12) has been set as the USB operating clock, the hub block alone can operate. USB Function Stop State: When the FNCSTP bit is set to 1 in USBCR, the USB function stop state is entered. In the USB function stop state, the USB function is disconnected from the bus. If the FONLY bit has been cleared to 0 in USBCR, internal connection between the USB function and USB hub is also cut. If the FONLY bit has been set to 1, the USB function is connected to the upstream port USD+/USD– pins. If the FNCSTP bit and FSRST bits are both set to 1, the USD+/USD– pins go to the high-impedance state. The USB operating clock supply to the USB function block is halted. Clearing the USB function stop state requires execution of the USB function block related sequence described in section 7.3.9, USB Module Startup Sequence. When setting the USB function stop state, it is recommended that the UIFRST, FPLLRST, and FSRST bits be set to 1 in USBCR in preparation for reduced current dissipation and release. As a result, the following registers are initialized. Rev. 3.00 Mar 17, 2006 page 160 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Registers UIFRST/FSRS EPDR2, EPDR1, EPDR0O, EPDR0I FSRST FVSR2, FVSR1, FVSR0O, FVSR0I FSRST EPSZR1 UIFRST USBIER UIFRST USBIFR, TSFR, TFFR FSRST USBCSR0 FSRST EPSTLR FSRST EPDIR UIFRST INTSELR0, INTSELR1 UIFRST Notes Bits 3 to 0 only USB Function Only State: When the FONLY bit is set to 1 in USBCR, the USB function only state is entered. In the USB function stop state, the USB function is connected to the upstream port, and the USB operating clock supply to the USB hub block is halted. It is recommended that USB hub block operation be halted by setting the HSRST bit to 1. This will place the downstream ports in the high-impedance state and enable port D, which also has a downstream port function, to operate as a general I/O port. HOCCR should be initialized to H'00. USB Bus Reset State: When a new device is connected to the USB bus, or when error recovery is executed, the USD+/USD– pin signals go to the bus reset state for a given period. In the USB function, the bus reset interrupt flag is set to 1 when a USB bus reset is detected. A bus reset initializes the USB hub internal state to the default state. Control registers that select the USB function internal state and USB function operating state are not initialized by a USB bus reset. These registers must be initialized by setting the FSRST bit to 1. Registers initialized by the UIFRST bit are not initialized by a USB bus reset. USB Suspend State: If the USB bus remains idle for longer than a certain time, the USB hub block and USB function block enter the suspend state. In the suspend state, some operating clocks are halted internally and current dissipation is reduced. When the USB function enters the suspend state, or when the suspend state is cleared by a change in the USD+/USD– pin signals, the suspend IN interrupt flag or suspend OUT interrupt flag, respectively, is set to 1. The remote wakeup from the suspend state can be executed by write 1 to the DVR bit in DEVRSMR. Rev. 3.00 Mar 17, 2006 page 161 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.3.9 USB Module Startup Sequence Component Elements: The USB module has a number of component elements requiring startup in a fixed sequence by firmware (an H8 program) to ensure normal operation and correct recognition by the USB host. The USB components that need to be considered are as follows: a. USB clock pulse generator (12 MHz), USB operating clock generation PLL (48 MHz) b. USB bus clock synchronization DPLL (12 MHz) c. EPINFO—Endpoint configuration information d. Slave CPU, core interface e. USB hub core, USB function core a. USB clock pulse generator (12 MHz), USB operating clock generation PLL (48 MHz) The USB clock pulse generator is connected to XTAL12-EXTAL12 and generates a 12 MHz USB clock. The USB operating clock PLL, multiplies the clock input from the USB clock pulse generator or system clock pulse generator to give a 48 MHz clock. The input clock frequency must be 8, 12, 16, or 20 MHz. As USB clock pulse generator oscillation has not started when a system reset is released, an oscillation stabilization period 10 ms that includes the USB operating clock PLL must be provided by firmware. Oscillation is started when XTAL12-EXTAL12 is set as the USB clock source with the CKSEL bits in UPLLCR. The PLL multiplication factor is selected with the PFSEL bits in UPLLCR. While waiting for oscillation to stabilize 10 ms, the UIFRST, HPLLRST, HSRST, FPLLRST, and FSRST bits are set to 1 in USBCR, placing the USB bus clock synchronization DPLL, USB hub core, USB function core, etc., in the reset state. b. USB bus clock synchronization DPLL (12 MHz) USB data transfer is performed at a maximum rate of 12 Mbps. The bit data sampling timing can be controlled by adjusting the phase during reception of the synchronization pattern that precedes a packet, using the 48 MHz USB operating clock. This mechanism is called the USB bus clock synchronization DPLL. A USB bus clock synchronization DPLL operation stabilization period must be provided by firmware. While waiting for operation to stabilize, the HSRST and FSRST bits are set to 1 in USBCR, placing the USB hub core, USB function core, etc., in the reset state. An operation stabilization period of at least ten 48 MHz clock cycles is recommended. Rev. 3.00 Mar 17, 2006 page 162 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) c. EPINFO—Endpoint configuration information The USB function core block can handle both bulk transfer and isochronous transfer, but for reasons related to the CPU interface specifications and the data transfer capability of the CPU itself, the H8 handles only control transfer and interrupt transfer processing. Information comprising settings for the number of endpoints, supported transfer types, maximum packet byte length, etc. (EPINFO) is written to the USB function block by firmware each time the USB function is initialized. In the H8/3567U and H8/3564U, three alternates are provided, and EPINFO is written for all three. However, since firmware has no way of knowing which alternate the host has selected, the module will not operate normally if the choice of alternate is changed during operation. The same alternate must be designated in the host driver software and the slave firmware. Table 7.5 shows the endpoint configuration information to be written to the USB function block. Write all 65 one-byte values to EPDR01 in the order A1, A2, .... A5, B1, B2, .... M4, M5. Table 7.5 Endpoint Configuration Information 1 2 3 4 5 A H'00 H'00 H'11 H'00 H'00 B H'14 H'38 H'10 H'00 H'01 C H'24 H'38 H'10 H'00 H'02 D H'14 H'78 H'10 H'00 H'01 E H'24 H'70 H'10 H'00 H'02 F H'14 H'B8 H'20 H'00 H'01 G H'35 H'20 H'10 H'00 H'03 H H'45 H'20 H'10 H'00 H'04 I H'55 H'20 H'10 H'00 H'05 J H'65 H'20 H'10 H'00 H'06 K H'36 H'20 H'10 H'00 H'03 L H'46 H'20 H'10 H'00 H'04 M H'56 H'20 H'10 H'00 H'05 d. Slave CPU, core interface These are the basic parts that execute firmware. The slave CPU begins operating immediately after reset release, whereas core interface access is enabled when the module stop state is cleared. Rev. 3.00 Mar 17, 2006 page 163 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) e. USB hub core, USB function core These are the central parts of the USB interface. Implementation of the USB bus interface is made possible by normal operation of component elements a to d. Initial Operation Procedures: The initial operation procedures for the USB hubs and USB function are shown in figures 7.5 and 7.6. When the USB module is used as a compound device, these two initial operation procedures must be executed, first for the USB hubs, then for the USB function. Clear the UIFRST bit to 0 before executing the USB function block procedure. The compound device initial operation procedure is summarized below. 1. H8 is in power-off or hardware standby state 2. Power-on, STBY pin high-level application, etc., is performed, and finally high level is applied to RES pin and H8 starts operating 3. USBE bit in STCR is set to 1 by firmware 4. USB module is released from module stop state by firmware 5. FONLY bit is cleared to 0 by firmware 6. HOCCR and PLLCR are set by firmware; wait for USB operating clock oscillation to stabilize 7. After elapse of 10 ms oscillation stabilization time, HPLLRST bit is cleared to 0 by firmware 8. After DPLL operation stabilization time, HSRST bit is cleared to 0 by firmware a. USB host (upstream port) performs USB hub block bus reset b. USB host performs USB hub block configuration c. → Start of USB hub block operation 9. UIFRST bit is cleared to 0 and USB function related registers are set by firmware 10. FNCSTP bit is cleared to 0 and USB function is connected to USB hub by firmware 11. FPLLRST bit is cleared to 0 by firmware 12. After DPLL operation stabilization time, FSRST bit is cleared to 0 by firmware 13. EPINFO is written to USB function core by firmware, and finally EPIVLD bit is set to 1 14. Wait for bus reset interrupt a. USB host (USB hub block) performs USB function block bus reset b. USB host performs USB function block configuration c. → Start of USB function block operation Rev. 3.00 Mar 17, 2006 page 164 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core USB hub core Power-on reset STBY = 0 RESET = 0 Standby release STBY = 1 Clock oscillation Reset release RESET = 1 System operation Set USBE bit to 1 in STCR USB module stop release Start of operation System clock oscillation HOCCR USBCR UPLLCR access OK Clear FONLY bit to 0 in USBCR Connect USB hub to upstream port HOCCR setting UPLLCR setting Downstream port control setting USB operating clock oscillation Start of USB operating clock supply Wait for USB operating clock oscillation stabilization time (10 ms) Clear HPLLRST bit to 0 in USBCR USBCR HPLLRST = 0 Start of DPLL block operation Wait for DPLL block operation stabilization Clear HSRST bit to 0 in USBCR USBCR HSRST = 0 Internal state reset release Bus reset by host Configuration by host Start of USB hub operation Figure 7.5 USB Hub Initial Operation Procedure Rev. 3.00 Mar 17, 2006 page 165 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core Power-on reset STBY = 0 RESET = 0 Standby release STBY = 1 Clock oscillation Reset release RESET = 1 System operation Set USBE bit to 1 in STCR Start of operation Compound device USB module stop release System clock oscillation HOCCR USBCR UPLLCR access OK UPLLCR setting USB operating clock oscillation Clear UIFRST bit to 0 in USBCR USB function related register access OK USB function related register settings USB function operation setting Clear FNCSTP bit to 0 in USBCR USB function connection Start of USB operating clock supply (Wait for USB operating clock oscillation stabilization time (10 ms)) Clear FPLLRST bit to 0 in USBCR USBCR FPLLRST = 0 Start of DPLL block operation Wait for DPLL block operation stabilization Clear FSRST bit to 0 in USBCR USBCR FSRST = 0 Internal state reset release Continued on next page Figure 7.6 USB Function Initial Operation Procedure Rev. 3.00 Mar 17, 2006 page 166 of 706 REJ09B0303-0300 USB hub core Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core USB hub core Continued from previous page EPINFO write to EPDR0I EPINFO transfer to core EPINFO recording Set EPIVLD bit to 1 in USBCSR0 End of EPINFO transfer End of EPINFO recording Bus reset interrupt handling (no action) Bus reset interrupt request Bus reset by host Configuration by host Start of USB function operation Figure 7.6 USB Function Initial Operation Procedure (cont) Disconnection/Reconnection Procedures: The initial operation procedures for USB hub/USB function disconnection and reconnection are shown in figures 7.7 to 7.10. There are three kinds of USB function disconnection: compound device hub block upstream disconnection, upstream disconnection in USB function standalone mode, and compound device function block disconnection by firmware. In the case of upstream disconnection, the USB bus continues in the idle state, and so the suspend state is entered. In order to detect reconnection, some method independent of the USB protocol is needed, such as detecting VBUS connection by means of an interrupt. Trigger events (such as cutoff of the system power supply) whereby the USB function block is disconnected by firmware also require detection by means of a separate interrupt, etc. When USB hub upstream disconnection occurs in the compound device state, the USB function block enters the suspend state. When upstream reconnection is detected by means of an external interrupt, etc., initialization of both the USB hub block and USB function block is performed by firmware. Rev. 3.00 Mar 17, 2006 page 167 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) The compound device upstream port disconnection/reconnection procedure is as follows: 1. Upstream port is disconnected 2. USB hub block and USB function block enter suspend state, and suspend IN interrupt is generated in USB function block 3. Upstream port is reconnected 4. Upstream port reconnection is detected by means of external interrupt, etc. 5. HSRST and FSRST bits are set to 1 by firmware 6. Step 8 in initial operation procedure is executed 7 onward: Operations from step 12 onward in initial operation procedure are executed The compound device USB function block disconnection/reconnection procedure is as follows: 1. State requiring disconnection of USB function is detected 2. Bits FNCSTP, FPLLRST, and FSRST are set to 1 If necessary, software standby mode is set 3. Detection of event enabling reconnection of USB function Software standby mode is exited 4. If necessary, USB function control registers are re-set 5. FNCSTP bit is cleared to 0 6. FPLLRST bit is cleared to 0 7. FSRST bit is cleared to 0 8 onward: Operations from step 13 onward in initial operation procedure are executed Rev. 3.00 Mar 17, 2006 page 168 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface Upstream port disconnection USB hub core Suspend state transition USB operating clock halted Upstream port reconnection USB function core USB operating clock supply halted Reconnection recognized by means of external interrupt Set HSRST bit to 1 in USBCR USBCR HSRST = 1 USB operating clock oscillation Internal state reset USB operating clock supply started Suspend state release Wait for DPLL block operation stabilization Clear HSRST bit to 0 in USBCR USBCR HSRST = 0 Internal state reset release Bus reset by host Configuration by host Start of USB hub operation Figure 7.7 USB Hub Block Upstream Disconnection/Reconnection Rev. 3.00 Mar 17, 2006 page 169 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core Upstream port disconnection Suspend state transition USB hub operating clock halted Suspend IN interrupt handling Set CKSTOP bit to 1 in USBCSR0 Upstream port reconnection USB hub core USB operating clock supply halted Suspend IN interrupt request Suspend state transition USB function operating clock halted USB operating clock supply halted Reconnection recognized by means of external interrupt Set HSRST bit and FSRST bit to 1 in USBCR USBCR HSRST = 1 FSRST = 1 USB operating clock oscillation Internal state reset USB operating clock supply started Suspend state release Wait for DPLL block operation stabilization Clear HSRST bit to 0 in USBCR USBCR HSRST = 0 Clear FSRST bit to 0 in USBCR USBCR FSRST = 0 Internal state reset release EPINFO write to EPDR0I EPINFO transfer to core EPINFO recording Set EPIVLD bit to 1 in USBCSR0 End of EPINFO transfer End of EPINFO recording Internal state reset USB operating clock supply started Suspend state release Internal state reset release Bus reset by host Continued on next page Figure 7.8 USB Compound Device Upstream Disconnection/Reconnection Rev. 3.00 Mar 17, 2006 page 170 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core USB hub core Continued from previous page Configuration by host Start of USB hub operation Bus reset interrupt handling (no action) Bus reset interrupt request Bus reset by host USB function connection recognized Configuration by host Start of USB function operation Figure 7.8 USB Compound Device Upstream Disconnection/Reconnection (cont) Rev. 3.00 Mar 17, 2006 page 171 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event Upstream port disconnection Upstream port reconnection USB operating clock PLL Slave CPU Core interface USB function core USB hub core Suspend state transition Suspend IN interrupt handling Set CKSTOP bit to 1 in USBCSR0 Suspend IN interrupt request USB function operating clock halted USB operating clock supply halted Reconnection recognized by means of external interrupt Set FSRST bit to 1 in USBCR USBCR FSRST = 1 USB operating clock oscillation Internal state reset USB operating clock supply started Suspend state release Wait for DPLL block operation stabilization Clear FSRST bit to 0 in USBCR USBCR FSRST = 0 Internal state reset release EPINFO write to EPDR0I EPINFO transfer to core EPINFO recording Set EPIVLD bit to 1 in USBCSR0 End of EPINFO transfer End of EPINFO recording Bus reset interrupt handling (no action) Bus reset interrupt request Bus reset by host Configuration by host Start of USB hub operation Figure 7.9 USB Function Standalone Mode Upstream Disconnection/Reconnection Rev. 3.00 Mar 17, 2006 page 172 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event Trigger event USB operating clock PLL Slave CPU USB function core USB hub core Detection of state requiring disconnection Set bits FNCSTP, FPLLRST, FSRST to 1 in USBCR Trigger event Core interface USBCR FNCSTP = 1 FPLLRST = 1 FSRST = 1 USB function disconnection DPLL block operation halted Internal state reset USB function disconnection recognized Detection of state enabling reconnection If necessary, re-set USB function related registers USB function operation re-setting Clear FNCSTP bit to 0 in USBCR USB function connection USB operating clock oscillation USB operating clock supply halted USB function connection recognized Clear FPLLRST bit to 0 in USBCR USBCR FPLLRST = 0 DPLL block operation started Wait for DPLL block operation stabilization Clear FSRST bit to 0 in USBCR USBCR FSRST = 0 Internal state reset release Continued on next page Figure 7.10 USB Function Block Disconnection/Reconnection Rev. 3.00 Mar 17, 2006 page 173 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) External event USB operating clock PLL Slave CPU Core interface USB function core USB hub core Continued from previous page EPINFO write to EPDR0I EPINFO transfer to core EPINFO recording Set EPIVLD bit to 1 in USBCSR0 End of EPINFO transfer End of EPINFO recording Bus reset interrupt handling (no action) Bus reset interrupt request Bus reset by host Configuration by host Start of USB function operation Figure 7.10 USB Function Block Disconnection/Reconnection (cont) Rev. 3.00 Mar 17, 2006 page 174 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) 7.3.10 USB Module Slave CPU Interrupts The USB module has four slave CPU interrupt sources: USBIA, USBIB, USBIC and USBID. Table 7.6 shows the interrupt sources and their priority order. The interrupt sources are the USBIFR and TSFR/TFFR interrupt flags. For each interrupt, the interrupt flag can be enabled or disabled by means of the corresponding interrupt enable bit in USBIER. In the USBID interrupt handling routine, USBIFR and TSFR/TFFR must be read to determine the interrupt source before processing is carried out. Table 7.6 USB Interrupt Sources Interrupt Source Description Priority USBIA Interrupt initiated by SETUP High USBIB Interrupt initiated by EPTS or EPTF of endpoint specified by INTSELR0 USBIC Interrupt initiated by EPTS or EPTF of endpoint specified by INTSELR0 USBID Interrupt initiated by SOF, SPND, BRST, TS, or TF Low Rev. 3.00 Mar 17, 2006 page 175 of 706 REJ09B0303-0300 Section 7 Universal Serial Bus Interface (USB) Rev. 3.00 Mar 17, 2006 page 176 of 706 REJ09B0303-0300 Section 8 I/O Ports Section 8 I/O Ports 8.1 Overview The H8/3577 Group has six input/output ports (ports 1 to 6), and one input-only port (port 7). The H8/3567 Group has four input/output ports (ports 1, 4, 5, and 6), and one input-only port. H8/3567 Group models with an on-chip USB have additional USB pins plus two input/output ports (ports C and D) for controlling the USB power supply circuit. Table 8.1 summarizes the port functions. The pins of each port also have other functions. Each port includes a data direction register (DDR) that controls input/output (not provided for the input-only ports), and a data register (DR) that stores output data. H8/3577 Group ports 1 to 3 have a built-in MOS input pull-up function, and use DDR and a MOS input pull-up control register (PCR) to control the on/off status of the MOS input pull-ups. Ports 1 to 6 can drive one TTL load and a 30 pF capacitive load. All the input/output ports can drive a Darlington transistor pair when in output mode. The output type of pin P52 in port 5 and pin P47 in port 4 is NMOS push-pull. Port C has the same load drive capacity as ports 1 to 6. Port D also has a USB hub downstream input/output function, and operates on the USB power supply (3.3 V). Rev. 3.00 Mar 17, 2006 page 177 of 706 REJ09B0303-0300 Section 8 I/O Ports Table 8.1 Port Port 1 H8/3577 Group and H8/3567 Group Port Functions Summary Pins • 8-bit I/O port P17/PW7 (/SCL1) • Built-in MOS input pull-up (H8/3577 Group only) P16/PW6 (/SDA1) P15/PW5 (/CBLANK) P14/PW4 P13/PW3 P12/PW2 Description I/O port also functioning as PWM timer output pins (PW7 to PW0, PWX1, PWX0) (both H8/3577 and H8/3567 Group) Additional functions: timer connection output pin (CBLANK) and I2C bus interface 1 I/O pins (SCL1, SDA1) (H8/3567 Group only) P11/PW1/PWX1 P10/PW0/PWX0 Port 2 • 8-bit I/O port H8/3577 Group: Present H8/3567 Group: Absent • Built-in MOS input pull-up (H8/3577 Group only) P27/PW15/CBLANK P26/PW14 P25/PW13 I/O port also functioning as PWM timer output pins (PW15 to PW8), or timer connection output pin (CBLANK) and I2C bus interface 1 I/O pins (SCL1, SDA1) P24/PW12/SCL1 P23/PW11/SDA1 P22/PW10 P21/PW9 P20/PW8 Port 3 • 8-bit I/O port P37 to P30 I/O port P47/SDA0 I/O port also functioning as I2C bus interface 0 I/O pin (SDA0) P46/φ When DDR = 0 (after reset): Input port H8/3577 Group: Present H8/3567 Group: Absent • Built-in MOS input pull-up (H8/3577 Group only) Port 4 • 8-bit I/O port When DDR = 1: φ output pin P45 to P43 I/O ports P42/IRQ0 I/O ports also functioning as external interrupt input pins (IRQ0, IRQ1) P41/IRQ1 P40/IRQ2/ADTRG Rev. 3.00 Mar 17, 2006 page 178 of 706 REJ09B0303-0300 I/O port also functioning as external interrupt input pin (IRQ2) and A/D converter external trigger input pin (ADTRG) Section 8 I/O Ports Port Port 5 Summary • 3-bit I/O port Pins P52/SCK0/SCL0 P51/RxD0 P50/TxD0 Port 6 • 8-bit I/O port P67/TMOX/TMO1/HSYNCO P66/FTOB/TMRI1/CSYNCI P65/FTID/TMCI1/HSYNCI P64/FTIC/TMO0/CLAMPO P63/FTIB/TMRI0/VFBACKI P62/FTIA/TMIY/VSYNCI Description I/O port also functioning as SCI0 I/O pins (TxD0, RxD0, SCK0) and I2C bus interface 0 I/O pin (SCL0) I/O port also functioning as FRT I/O pins (FTCI, FTOA, FTIA, FTIB, FTIC, FTID, FTOB), 8-bit timer 0 and 1 I/O pins (TMCI0, TMRI0, TMO0, TMCI1, TMRI1, TMO1), 8-bit timer X and Y I/O pins (TMOX, TMIX, TMIY), and timer connection I/O pins (HSYNCO, CSYNCI, HSYNCI, CLAMPO, VFBACKI, VSYNCI, VSYNCO, HFBACKI) P61/FTOA/VSYNCO P60/FTCI/TMIX/TMCI0/ HFBACKI Port 7 • 8-bit input port (H8/3577 Group) P77 to P74/AN7 to AN4 P73 to P70/AN3 to AN0 I/O port also functioning as A/D converter analog inputs (AN7 to AN0) • 4-bit input port (H8/3567 Group) Port C • 8-bit I/O port (H8/3567 Group version with on-chip USB only) Port D • 8-bit I/O port (H8/3567 Group version with on-chip USB only) Power supply: DrVCC (3.3 V) PC7 to PC4/OCP5 to OCP2 PC3 to PC0/ENP5 to ENP2 PD7/DS5D–, PD6/DS5D+, PD5/DS4D–, PD4/DS4D+, I/O port also functioning as external power supply circuit overcurrent detection signal input pins (OCP5 to OCP2) and power output enable signal output pins (ENP5 to ENP2) I/O port also functioning as USB downstream I/O pins PD3/DS3D–, PD2/DS3D+, PD1/DS2D–, PD0/DS2D+ Rev. 3.00 Mar 17, 2006 page 179 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.2 Port 1 8.2.1 Overview Port 1 is an 8-bit I/O port. Port 1 is also used for 8-bit PWM output (PW7 to PW0), 14-bit PWM output (PWX1, PWX0), timer connection output (CBLANK) [H8/3567 Group only], and IIC1 input/output (SCL1, SDA1) [H8/3567 Group only]. In the H8/3577 Group, port 1 has a built-in MOS input pull-up function that can be controlled by software. Figure 8.1 shows the port 1 pin configuration. P1n: Input pin when P1DDR = 0, output pin when P1DDR = 1 and PWOERA = 0 P17 (input/output) / SCL1 (H8/3567 Group: input/output) P16 (input/output) / SDA1 (H8/3567 Group: input/output) P15 (input/output) / CBLANK (H8/3567 Group: output) Port 1 P14 (input/output) P13 (input/output) P12 (input/output) P11 (input/output) / PWX1 (output) P10 (input/output) / PWX0 (output) When P1DDR = 1 and PWOERA = 1 PW7 (output) / SCL1 (H8/3567 Group: input/output) PW6 (output) / SDA1 (H8/3567 Group: input/output) PW5 (output) / CBLANK (H8/3567 Group: output) PW4 (output) PW3 (output) PW2 (output) PW1 (output) / PWX1 (output) PW0 (output) / PWX0 (output) Figure 8.1 Port 1 Pin Functions Rev. 3.00 Mar 17, 2006 page 180 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.2.2 Register Configuration Table 8.2 shows the port 1 register configuration. Table 8.2 Port 1 Registers Name Abbreviation R/W Initial Value Address Port 1 data direction register P1DDR W H'00 H'FFB0 Port 1 data register P1DR R/W H'00 H'FFB2 Port 1 MOS pull-up control register* [H8/3577 Group only] P1PCR R/W H'00 H'FFAC Note: * P1PCR cannot be read or written to in the H8/3567 Group. A read will return an undefined value. Port 1 Data Direction Register (P1DDR) Bit 7 6 5 4 3 2 1 0 P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR P11DDR P10DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P1DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 1. P1DDR cannot be read; if it is, an undefined value will be returned. P1DDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Setting a P1DDR bit to 1 makes the corresponding port 1 pin an output port or PWM output, while clearing the bit to 0 makes the pin an input port. P10 and P11 can be used for PWMX output regardless of the P1DDR settings. In the H8/3567 Group, P17, P16, and P15 can be used for supporting function output or input/output regardless of the P1DDR settings. Rev. 3.00 Mar 17, 2006 page 181 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 1 Data Register (P1DR) Bit 7 6 5 4 3 2 1 0 P17DR P16DR P15DR P14DR P13DR P12DR P11DR P10DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P1DR is an 8-bit readable/writable register that stores output data for the port 1 pins (P17 to P10). If a port 1 read is performed while P1DDR bits are set to 1, the P1DR values are read directly regardless of the actual pin states. If a port 1 read is performed while P1DDR bits are cleared to 0, the pin states are read. P1DR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port 1 MOS Pull-Up Control Register (P1PCR) Bit 7 6 5 4 3 2 1 0 P17PCR P16PCR P15PCR P14PCR P13PCR P12PCR P11PCR P10PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P1PCR is an 8-bit readable/writable register that controls the MOS input pull-up function incorporated into port 1 on a bit-by-bit basis. When a P1DDR bit is cleared to 0 (input port setting), setting the corresponding P1PCR bit to 1 turns on the MOS input pull-up for that pin. P1PCR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. 8.2.3 Pin Functions Port 1 is used for PWM output or as an I/O port, with input or output specifiable individually for each pin. Setting a P1DDR bit to 1 makes the corresponding port 1 pin a PWM output or output port, while clearing the bit to 0 makes the pin an input port. P10 and P11 can be used for PWMX output regardless of the P1DDR settings. Rev. 3.00 Mar 17, 2006 page 182 of 706 REJ09B0303-0300 Section 8 I/O Ports In the H8/3567 Group, P17, P16, and P15 also function as IIC1 I/O pins (SCL1, SDA1) and the timer connection output pin (CBLANK). P17, P16, and P15 can be used for supporting function input/output regardless of the P1DDR settings. Port 1 pin functions are shown in table 8.3. Table 8.3 Port 1 Pin Functions Pin Pin Functions and Selection Method P17/PW7 (/SCL1) The pin function is selected as shown below by a combination of bit ICE in ICCR of IIC1 (H8/3567 Group), bit OE7 in PWOERA, and bit P17DDR. ICE 0 PWOERA: OE7 — 0 1 — P17 input P17 output PW7 output SCL1 I/O 1 — The pin function is selected as shown below by a combination of bit ICE in ICCR of IIC1 (H8/3567 Group), bit OE6 in PWOERA, and bit P16DDR. ICE 0 1 P16DDR 0 PWOERA: OE6 — 0 1 — P16 input P16 output PW6 output SDA1 I/O Pin function P15/PW5 (/CBLANK) 1 P17DDR Pin function P16/PW6 (/SDA1) 0 1 — The pin function is selected as shown below by a combination of bit CBE in timer connection TCONR0 (H8/3567 Group), bit OE5 in PWOERA, and bit P15DDR. CBE P15DDR PWOERA: OE5 Pin function 0 0 1 1 — — 0 1 — P15 input P15 output PW5 output CBLANK output Rev. 3.00 Mar 17, 2006 page 183 of 706 REJ09B0303-0300 Section 8 I/O Ports Pin P14/PW4 Pin Functions and Selection Method P14DDR 0 PWOERA: OE4 0 0 1 P14 input P14 output PW4 output Pin function P13/PW3 P13DDR 0 PWOERA: OE3 0 0 1 P13 input P13 output PW3 output Pin function P12/PW2 0 PWOERA: OE2 0 0 1 P12 input P12 output PW2 output 1 The pin function is selected as shown below by a combination of bit OEB in DACR of PWMX, bit OE1 in PWOERA, and bit P11DDR. DACR: OEB 0 P11DDR 0 PWOERA: OE1 Pin function P10/PW0/ PWX0 1 P12DDR Pin function P11/PW1/ PWX1 1 1 1 — — 0 1 — P11 input P11 output PW1 output PWX1 output The pin function is selected as shown below by a combination of bit OEA in DACR of PWMX, bit OE0 in PWOERA, and bit P10DDR. DACR: OEA 0 1 P10DDR 0 PWOERA: OE0 — 0 1 — P10 input P10 output PW0 output PWX0 output Pin function Rev. 3.00 Mar 17, 2006 page 184 of 706 REJ09B0303-0300 1 — Section 8 I/O Ports 8.2.4 MOS Input Pull-Up Function In the H8/3577 Group, port 1 has a built-in MOS input pull-up function that can be controlled by software. When a P1DDR bit is cleared to 0, setting the corresponding P1PCR bit to 1 turns on the MOS input pull-up for that pin. The MOS input pull-up function is in the off state after a reset and in hardware standby mode. The previous state is retained in software standby mode. Table 8.4 summarizes the MOS input pull-up states. Table 8.4 MOS Input Pull-Up States (Port 1) Reset Hardware Standby Mode Software Standby Mode In Other Operations Off Off On/Off On/Off Legend: Off: MOS input pull-up is always off. On/Off: On when P1DDR = 0 and P1PCR = 1; otherwise off. Rev. 3.00 Mar 17, 2006 page 185 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.3 Port 2 [H8/3577 Group Only] 8.3.1 Overview Port 2 is an 8-bit I/O port. Port 2 is also used for 8-bit PWM output (PW15 to PW8), timer connection output (CBLANK), and IIC1 input/output (SCL1, SDA1). Port 2 is provided in the H8/3577 Group, but not in the H8/3567 Group. Therefore the H8/3567 Group does not have the port 2 I/O pin functions or eight 8-bit PWM output pin (PW15 to PW8) functions, and provides the timer connection output pin (CBLANK) function and IIC1 I/O pin (SCL1, SDA1) functions in port 1. Port 2 has a built-in MOS input pull-up function that can be controlled by software. Figure 8.2 shows the port 2 pin configuration. P2n: Input pin when P2DDR = 0, output pin when P2DDR = 1 and PWOERB = 0 P27 (input/output) / CBLANK (output) P26 (input/output) P25 (input/output) Port 2 P24 (input/output) / SCL1 (input/output) P23 (input/output) / SDA1 (input/output) P22 (input/output) P21 (input/output) P20 (input/output) When P2DDR = 1 and PWOERB = 1 PW15 (output) / CBLANK (output) PW14 (output) PW13 (output) PW12 (output) / SCL1 (input/output) PW11 (output) / SDA1 (input/output) PW10 (output) PW9 (output) PW8 (output) Figure 8.2 Port 2 Pin Functions Rev. 3.00 Mar 17, 2006 page 186 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.3.2 Register Configuration Table 8.5 shows the port 2 register configuration. Table 8.5 Port 2 Registers Name Abbreviation R/W Initial Value Address Port 2 data direction register P2DDR W H'00 H'FFB1 Port 2 data register P2DR R/W H'00 H'FFB3 Port 2 MOS pull-up control register P2PCR R/W H'00 H'FFAD Port 2 Data Direction Register (P2DDR) Bit 7 6 5 4 3 2 1 0 P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR P21DDR P20DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P2DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 2. P2DDR cannot be read; if it is, an undefined value will be returned. P2DDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Setting a P2DDR bit to 1 makes the corresponding port 2 pin an output port or PWM output, while clearing the bit to 0 makes the pin an input port. P23, P24, and P27 can be used for supporting function output regardless of the P2DDR settings. Rev. 3.00 Mar 17, 2006 page 187 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 2 Data Register (P2DR) Bit 7 6 5 4 3 2 1 0 P27DR P26DR P25DR P24DR P23DR P22DR P21DR P20DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P2DR is an 8-bit readable/writable register that stores output data for the port 2 pins (P27 to P20). If a port 2 read is performed while P2DDR bits are set to 1, the P2DR values are read directly regardless of the actual pin states. If a port 2 read is performed while P2DDR bits are cleared to 0, the pin states are read. P2DR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port 2 MOS Pull-Up Control Register (P2PCR) Bit 7 6 5 4 3 2 1 0 P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR P21PCR P20PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P2PCR is an 8-bit readable/writable register that controls the MOS input pull-up function incorporated into port 2 on a bit-by-bit basis. When a P2DDR bit is cleared to 0 (input port setting), setting the corresponding P2PCR bit to 1 turns on the MOS input pull-up for that pin. P2PCR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Rev. 3.00 Mar 17, 2006 page 188 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.3.3 Pin Functions Port 2 is used for PWM output, timer connection output (CBLANK), and IIC1 input/output (SCL1, SDA1), or as an I/O port, with input or output specifiable individually for each pin. Setting a P2DDR bit to 1 makes the corresponding port 2 pin a PWM output or output port, while clearing the bit to 0 makes the pin an input port. P23, P24, and P27 can be used for supporting function output regardless of the P2DDR settings. Port 2 pin functions are shown in table 8.6. Table 8.6 Port 2 Pin Functions Pin Pin Functions and Selection Method P27/PW15/ CBLANK The pin function is selected as shown below by a combination of bit CBE in timer connection TCONR0, bit OE15 in PWOERB, and bit P27DDR. CBE PWOERB: OE15 — 0 1 — P27 input P27 output PW15 output CBLANK output — 0 PWOERB: OE14 0 0 1 P26 input P26 output PW14 output P25DDR Pin function 1 0 PWOERB: OE13 P24/PW12/ SCL1 1 P26DDR Pin function P25/PW13 1 0 Pin function P26/PW14 0 P27DDR 1 0 0 1 P25 input P25 output PW13 output The pin function is selected as shown below by a combination of bit ICE in ICCR of IIC1, bit OE12 in PWOERB, and bit P24DDR. ICE 0 1 P24DDR 0 PWOERB: OE12 — 0 1 — P24 input P24 output PW12 output SCL1 I/O Pin function 1 — Rev. 3.00 Mar 17, 2006 page 189 of 706 REJ09B0303-0300 Section 8 I/O Ports Pin Pin Functions and Selection Method P23/PW11/ SDA1 The pin function is selected as shown below by a combination of bit ICE in ICCR of IIC1, bit OE11 in PWOERB, and bit P23DDR. ICE PWOERB: OE11 — 0 1 — P23 input P23 output PW11 output SDA1 I/O — 0 PWOERB: OE10 0 0 1 P22 input P22 output PW10 output 1 P21DDR 0 PWOERB: OE9 0 0 1 P21 input P21 output PW9 output Pin function P20/PW8 1 P22DDR Pin function P21/PW9 1 0 Pin function P22/PW10 0 P23DDR P20DDR PWOERB: OE8 Pin function Rev. 3.00 Mar 17, 2006 page 190 of 706 REJ09B0303-0300 1 0 1 0 0 1 P20 input P20 output PW8 output Section 8 I/O Ports 8.3.4 MOS Input Pull-Up Function Port 2 has a built-in MOS input pull-up function that can be controlled by software. MOS input pull-up can be specified as on or off for individual bits. When a P2DDR bit is cleared to 0, setting the corresponding P2PCR bit to 1 turns on the MOS input pull-up for that pin. The MOS input pull-up function is in the off state after a reset and in hardware standby mode. The previous state is retained in software standby mode. Table 8.7 summarizes the MOS input pull-up states. Table 8.7 MOS Input Pull-Up States (Port 2) Reset Hardware Standby Mode Software Standby Mode In Other Operations Off Off On/Off On/Off Legend: Off: MOS input pull-up is always off. On/Off: On when P2DDR = 0 and P2PCR = 1; otherwise off. Rev. 3.00 Mar 17, 2006 page 191 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.4 Port 3 [H8/3577 Group Only] 8.4.1 Overview Port 3 is an 8-bit I/O port. Port 3 is provided in the H8/3577 Group, but not in the H8/3567 Group. Port 3 has a built-in MOS input pull-up function that can be controlled by software. Figure 8.3 shows the port 3 pin configuration. P37 (input/output) P36 (input/output) P35 (input/output) P34 (input/output) Port 3 P33 (input/output) P32 (input/output) P31 (input/output) P30 (input/output) Figure 8.3 Port 3 Pin Functions 8.4.2 Register Configuration Table 8.8 shows the port 3 register configuration. Table 8.8 Port 3 Registers Name Abbreviation R/W Initial Value Address Port 3 data direction register P3DDR W H'00 H'FFB4 Port 3 data register P3DR R/W H'00 H'FFB6 Port 3 MOS pull-up control register P3PCR R/W H'00 H'FFAE Rev. 3.00 Mar 17, 2006 page 192 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 3 Data Direction Register (P3DDR) Bit 7 6 5 4 3 2 1 0 P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR P31DDR P30DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P3DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 3. P3DDR cannot be read; if it is, an undefined value will be returned. P3DDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Setting a P3DDR bit to 1 makes the corresponding port 3 pin an output port, while clearing the bit to 0 makes the pin an input port. Port 3 Data Register (P3DR) Bit 7 6 5 4 3 2 1 0 P37DR P36DR P35DR P34DR P33DR P32DR P31DR P30DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P3DR is an 8-bit readable/writable register that stores output data for the port 3 pins (P37 to P30). If a port 3 read is performed while P3DDR bits are set to 1, the P3DR values are read directly regardless of the actual pin states. If a port 3 read is performed while P3DDR bits are cleared to 0, the pin states are read. P3DR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port 3 MOS Pull-Up Control Register (P3PCR) Bit 7 6 5 4 3 2 1 0 P37PCR P36PCR P35PCR P34PCR P33PCR P32PCR P31PCR P30PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P3PCR is an 8-bit readable/writable register that controls the MOS input pull-up function incorporated into port 3 on a bit-by-bit basis. Rev. 3.00 Mar 17, 2006 page 193 of 706 REJ09B0303-0300 Section 8 I/O Ports When a P3DDR bit is cleared to 0 (input port setting), setting the corresponding P3PCR bit to 1 turns on the MOS input pull-up for that pin. P3PCR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. 8.4.3 Pin Functions Port 3 is used as an I/O port, with input or output specifiable individually for each pin. Setting a P3DDR bit to 1 makes the corresponding port 3 pin an output port, while clearing the bit to 0 makes the pin an input port. 8.4.4 MOS Input Pull-Up Function Port 3 has a built-in MOS input pull-up function that can be controlled by software. MOS input pull-up can be specified as on or off for individual bits. When a P3DDR bit is cleared to 0, setting the corresponding P3PCR bit to 1 turns on the MOS input pull-up for that pin. The MOS input pull-up function is in the off state after a reset and in hardware standby mode. The previous state is retained in software standby mode. Table 8.9 summarizes the MOS input pull-up states. Table 8.9 MOS Input Pull-Up States (Port 3) Reset Hardware Standby Mode Software Standby Mode In Other Operations Off Off On/Off On/Off Legend: Off: MOS input pull-up is always off. On/Off: On when P3DDR = 0 and P3PCR = 1; otherwise off. Rev. 3.00 Mar 17, 2006 page 194 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.5 Port 4 8.5.1 Overview Port 4 is an 8-bit I/O port. Port 4 is also used for external interrupt input (IRQ0 to IRQ2), A/D converter input (ADTRG), IIC0 input/output (SDA0), and system clock (φ) output. The output type of P47 is NMOS push-pull. The output type of SDA0 is NMOS open-drain with direct bus drive capability. Figure 8.4 shows the port 4 pin configuration. P47 (input/output) / SDA0 (input/output) P46 (input/output) / φ (output) P45 (input/output) Port 4 P44 (input/output) P43 (input/output) P42 (input/output) / IRQ0 (input) P41 (input/output) / IRQ1 (input) P40 (input/output) / IRQ2 (input) / ADTRG (input) Figure 8.4 Port 4 Pin Functions 8.5.2 Register Configuration Table 8.10 shows the port 4 register configuration. Table 8.10 Port 4 Registers Name Abbreviation R/W Initial Value Address Port 4 data direction register P4DDR W H'00 H'FFB5 Port 4 data register P4DR R/W H'00 H'FFB7 Rev. 3.00 Mar 17, 2006 page 195 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 4 Data Direction Register (P4DDR) Bit 7 6 5 4 3 2 1 0 P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR P41DDR P40DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P4DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 4. P4DDR cannot be read; if it is, an undefined value will be returned. P4DDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. When P4DDR bits are set to 1, pin P46 functions as the φ output pin, and pins P47 and P45 to P40 function as output ports. Clearing a P4DDR bit to 0 makes the corresponding pin an input port. Port 4 Data Register (P4DR) Bit 7 6 5 4 3 2 1 0 P47DR P46DR P45DR P44DR P43DR P42DR P41DR P40DR Initial value 0 —* 0 0 0 0 0 0 Read/Write R/W R R/W R/W R/W R/W R/W R/W Note: * Determined by the state of pin P46. P4DR is an 8-bit readable/writable register that stores output data for the port 4 pins (P47 to P40). Except for P46, if a port 4 read is performed while P4DDR bits are set to 1, the P4DR values are read directly regardless of the actual pin states. If a port 4 read is performed while P4DDR bits are cleared to 0, the pin states are read. P4DR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Rev. 3.00 Mar 17, 2006 page 196 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.5.3 Pin Functions Port 4 pins are also used for external interrupt input (IRQ0 to IRQ2), A/D converter input (ADTRG), IIC0 input/output (SDA0), and system clock (φ) output. Port 4 pin functions are shown in table 8.11. Table 8.11 Port 4 Pin Functions Pin Pin Functions and Selection Method P47/SDA0 The pin function is selected as shown below by a combination of bit ICE in ICCR of IIC0 and bit P47DDR. ICE P47DDR Pin function 0 1 0 1 — P47 input P47 output SDA0 I/O When this pin is designated as the P47 output pin, it is an NMOS push-pull output. The output type of SDA0 is NMOS open-drain with direct bus drive capability. P46/φ P46DDR Pin function P45 P45DDR Pin function P44 P44DDR Pin function P43 P43DDR Pin function P42/IRQ0 P42DDR Pin function 0 1 P46 input φ output 0 1 P45 input P45 output 0 1 P44 input P44 output 0 1 P43 input P43 output 0 1 P42 input P42 output IRQ0 input When bit IRQ0E is set to 1 in IER, this pin is used as the IRQ0 input pin. Rev. 3.00 Mar 17, 2006 page 197 of 706 REJ09B0303-0300 Section 8 I/O Ports Pin P41/IRQ1 Pin Functions and Selection Method P41DDR Pin function 0 1 P41 input P41 output IRQ1 input When bit IRQ1E is set to 1 in IER, this pin is used as the IRQ1 input pin. P40/IRQ2/ ADTRG P40DDR Pin function 0 1 P40 input P40 output IRQ2 input, ADTRG input When bit IRQ2E is set to 1 in IER, this pin is used as the IRQ2 input pin. When bits TRGS1 and TRGS0 are both set to 1 in the A/D converter’s ADCR register, this pin is used as the ADTRG input pin. Rev. 3.00 Mar 17, 2006 page 198 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.6 Port 5 8.6.1 Overview Port 5 is a 3-bit I/O port. Port 5 is also used for SCI0 input/output (TxD0, RxD0, SCK0) and IIC0 input/output (SCL0). The output type of P52 and SCK0 is NMOS push-pull. The output type of SCL0 is NMOS open-drain. Figure 8.5 shows the port 5 pin configuration. Port 5 pins P52 (input/output) / SCK0 (input/output) / SCL0 (input/output) Port 5 P51 (input/output) / RxD0 (input) P50 (input/output) / TxD0 (output) Figure 8.5 Port 5 Pin Functions 8.6.2 Register Configuration Table 8.12 shows the port 5 register configuration. Table 8.12 Port 5 Registers Name Abbreviation R/W Initial Value Address Port 5 data direction register P5DDR W H'F8 H'FFB8 Port 5 data register P5DR R/W H'F8 H'FFBA Rev. 3.00 Mar 17, 2006 page 199 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 5 Data Direction Register (P5DDR) Bit 7 6 5 4 3 2 1 0 — — — — — P52DDR P51DDR P50DDR Initial value 1 1 1 1 1 0 0 0 Read/Write — — — — — W W W P5DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 5. P5DDR cannot be read; if it is, an undefined value will be returned. Bits 7 to 3 are reserved. Setting a P5DDR bit to 1 makes the corresponding port 5 pin an output port, while clearing the bit to 0 makes the pin an input port. P5DDR is initialized to H'F8 by a reset and in hardware standby mode. It retains its previous state in software standby mode. As SCI0 is initialized, the pin states are determined by IIC0’s ICCR, P5DDR, and P5DR specifications. Port 5 Data Register (P5DR) Bit 7 6 5 4 3 2 1 0 — — — — — P52DR P51DR P50DR Initial value 1 1 1 1 1 0 0 0 Read/Write — — — — — R/W R/W R/W P5DR is an 8-bit readable/writable register that stores output data for the port 5 pins (P52 to P50). If a port 5 read is performed while P5DDR bits are set to 1, the P5DR values are read directly regardless of the actual pin states. If a port 5 read is performed while P5DDR bits are cleared to 0, the pin states are read. Bits 7 to 3 are reserved; they cannot be modified and are always read as 1. P5DR is initialized to H'F8 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Rev. 3.00 Mar 17, 2006 page 200 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.6.3 Pin Functions Port 5 pins are also used for SCI0 input/output (TxD0, RxD0, SCK0) and IIC0 input/output (SCL0). Port 5 pin functions are shown in table 8.13. Table 8.13 Port 5 Pin Functions Pin Pin Functions and Selection Method P52/SCK0/ SCL0 The pin function is selected as shown below by a combination of bit C/A in SMR of SCI0, bits CKE0 and CKE1 in SCR, bit ICE in ICCR of IIC0, and bit P52DDR. ICE 0 CKE1 C/A Pin function 1 0 1 — 0 1 — — 0 0 CKE0 P52DDR 1 0 0 0 1 — — — — P52 input P52 output SCK0 output SCK0 output SCK0 input SCL0 I/O When this pin is used as the SCL0 I/O pin, bits CKE1 and CKE0 in SCR of SCI0 and bit C/A in SMR must all be cleared to 0. The output type of SCL0 is NMOS open-drain with direct bus drive capability. When this pin is designated as the P52 output pin or SCK0 output pin, it is an NMOS push-pull output. P51/RxD0 The pin function is selected as shown below by a combination of bit RE in SCR of SCI0 and bit P51DDR. RE P51DDR Pin function P50/TxD0 0 1 0 1 — P51 input P51 output RxD0 input The pin function is selected as shown below by a combination of bit TE in SCR of SCI0 and bit P50DDR. TE P50DDR Pin function 0 1 0 1 — P50 input P50 output TxD0 output Rev. 3.00 Mar 17, 2006 page 201 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.7 Port 6 8.7.1 Overview Port 6 is an 8-bit I/O port. It is also used for 16-bit free-running timer (FRT) input/output (FTOA, FTOB, FTIA to FTID, FTCI), timer 0 and 1 (TMR0, TMR1) input/output (TMCI0, TMRI0, TMO0, TMCI1, TMRI1, TMO1), timer X (TMRX) input/output (TMOX, TMIX), timer Y (TMRY) input (TMIY), and timer connection input/output (CSYNCI, HSYNCI, HSYNCO, HFBACKI, VSYNCI, VSYNCO, VFBACKI, CLAMPO). Figure 8.6 shows the port 6 pin configuration. Port 6 pins P67 (input/output) / TMOX (output) / TMO1 (output) / HSYNCO (output) Port 6 P66 (input/output) / FTOB (output) / TMRI1 (input) / CSYNCI (input) P65 (input/output) / FTID (input) / TMCI1 (input) / HSYNCI (input) P64 (input/output) / FTIC (input) / TMO0 (output) / CLAMPO (output) P63 (input/output) / FTIB (input) / TMRI0 (input) P62 (input/output) / FTIA (input) / VSYNCI(input) / TMIY (input) / VFBACKI (input) P61 (input/output) / FTOA (output) / VSYNCO(output) P60 (input/output) / FTCI (input) / TMCI0 (input) / HFBACKI (input) / TMIX (input) Figure 8.6 Port 6 Pin Functions 8.7.2 Register Configuration Table 8.14 shows the port 6 register configuration. Table 8.14 Port 6 Registers Name Abbreviation R/W Initial Value Address Port 6 data direction register P6DDR W H'00 H'FFB9 Port 6 data register P6DR R/W H'00 H'FFBB Rev. 3.00 Mar 17, 2006 page 202 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 6 Data Direction Register (P6DDR) Bit 7 6 5 4 3 2 1 0 P67DDR P66DDR P65DDR P64DDR P63DDR P62DDR P61DDR P60DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P6DDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port 6. P6DDR cannot be read; if it is, an undefined value will be returned. Setting a P6DDR bit to 1 makes the corresponding port 6 pin an output port, while clearing the bit to 0 makes the pin an input port. P6DDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port 6 Data Register (P6DR) Bit 7 6 5 4 3 2 1 0 P67DR P66DR P65DR P64DR P63DR P62DR P61DR P60DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P6DR is an 8-bit readable/writable register that stores output data for the port 6 pins (P67 to P60). If a port 6 read is performed while P6DDR bits are set to 1, the P6DR values are read directly regardless of the actual pin states. If a port 6 read is performed while P6DDR bits are cleared to 0, the pin states are read. P6DR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. 8.7.3 Pin Functions Port 6 pins are also used for 16-bit free-running timer (FRT) input/output (FTOA, FTOB, FTIA to FTID, FTCI), timer 0 and 1 (TMR0, TMR1) input/output (TMCI0, TMRI0, TMO0, TMCI1, TMRI1, TMO1), timer X (TMRX) input/output (TMOX, TMIX), timer Y (TMRY) input (TMIY), and timer connection input/output (CSYNCI, HSYNCI, HSYNCO, HFBACKI, VSYNCI, VSYNCO, VFBACKI, CLAMPO. Port 6 pin functions are shown in table 8.15. Rev. 3.00 Mar 17, 2006 page 203 of 706 REJ09B0303-0300 Section 8 I/O Ports Table 8.15 Port 6 Pin Functions Pin Pin Functions and Selection Method P67/TMO1/ TMOX/ HSYNCO The pin function is selected as shown below by a combination of bits OS3 to OS0 in TCSR of TMR1 and TMRX, bit HOE of timer connection TCONRO, and bit P67DDR. HOE 0 TMRX: OS3–0 TMR1: OS3–0 All 0 P67DDR Pin function P66/FTOB/ TMRI1/CSYNCI 1 All 0 Not all 0 — Not all 0 — — 0 1 — — — P67 input P67 output TMO1 output TMOX output HSYNCO output The pin function is selected as shown below by a combination of bit OEB in TOCR of FRT and bit P66DDR. OEB 0 P66DDR Pin function 1 0 1 — P66 input P66 output FTOB output TMRI1 input, CSYNCI input When bits CCLR1 and CCLR0 are both set to 1 in TCR of TMR1, this pin is used as the TMRI1 input pin. P65/FTID/ TMCI1/HSYNCI P65DDR Pin function 0 1 P65 input P65 output FTID input, TMCI1 input, HSYNCI input When an external clock is selected with bits CKS2 to CKS0 in TCR of TMR1, this pin is used as the TMCI1 input pin. P64/FTIC/ TMO0/ CLAMPO The pin function is selected as shown below by a combination of bits OS3 to OS0 in TCSR of TMR0, bit CLOE of timer connection TCONRO, and bit P64DDR. CLOE 0 OS3–0 P64DDR Pin function 1 All 0 Not all 0 All 0 0 1 — — P64 input P64 output TMO0 output CLAMPO output FTIC input When this pin is used as the CLAMPO pin, bits OS3 to OS0 in TCSR of TMR0 must be cleared to 0. Rev. 3.00 Mar 17, 2006 page 204 of 706 REJ09B0303-0300 Section 8 I/O Ports Pin Pin Functions and Selection Method P63/FTIB/ P63DDR TMRI0/VFBACKI Pin function 0 1 P63 input P63 output FTIB input, TMRI0 input, VFBACKI input When bits CCLR1 and CCLR0 are both set to 1 in TCR of TMR0, this pin is used as the TMRI0 input pin. P62/FTIA/ VSYNCI/TMIY P62DDR Pin function 0 1 P62 input P62 output FTIA input, VSYNCI input, TMIY input P61/FTOA/ VSYNCO The pin function is selected as shown below by a combination of bit OEA in TOCR of FRT, bit VOE of timer connection TCONRO, and bit P61DDR. VOE 0 OEA P61DDR Pin function 0 1 1 0 0 1 — — P61 input P61 output FTOA0 output VSYNCO output When this pin is used as the VSYNCO pin, bit OEA in TOCR of FRT must be cleared to 0. P60/FTCI/TMCI0/ HFBACKI/TMIX P60DDR Pin function 0 1 P60 input P60 output FTCI input, TMCI0 input, HFBACKI input, TMIX input When an external clock is selected with bits CKS1 and CKS0 in TCR of FRT, this pin is used as the FTCI input pin. When an external clock is selected with bits CKS2 to CKS0 in TCR of TMR0, this pin is used as the TMCI0 input pin. Rev. 3.00 Mar 17, 2006 page 205 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.8 Port 7 8.8.1 Overview Port 7 is an 8-bit input port. Port 7 is also used for A/D converter analog input (AN7 to AN0). Bits 7 to 4 of port 7 are provided in the H8/3577 Group, but not in the H8/3567 Group. Therefore the H8/3567 Group does not have the input pin functions or four A/D converter analog input pin (AN7 to AN4) functions corresponding to bits 7 to 4 of port 7. Figure 8.7 shows the port 7 pin configuration. Port 7 pins P77 (input) / AN7 (input) P76 (input) / AN6 (input) P75 (input) / AN5 (input) P74 (input) / AN4 (input) Port 7 P73 (input) / AN3 (input) P72 (input) / AN2 (input) P71 (input) / AN1 (input) P70 (input) / AN0 (input) Figure 8.7 Port 7 Pin Functions 8.8.2 Register Configuration Table 8.16 shows the port 7 register configuration. As port 7 is an input port, it has no data direction register or data register. Table 8.16 Port 7 Registers Name Abbreviation R/W Initial Value Address Port 7 input data register P7PIN R Undefined H'FFBE Rev. 3.00 Mar 17, 2006 page 206 of 706 REJ09B0303-0300 Section 8 I/O Ports Port 7 Input Data Register (P7PIN) Bit 7 6 5 4 3 2 1 0 P77PIN P76PIN P75PIN P74PIN P73PIN P72PIN P71PIN P70PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Note: * Determined by the state of pins P77 to P70. When a P7PIN read is performed, the pin states are always read. In the H8/3567 Group, reading bits 7 to 4 will return an undefined value. 8.8.3 Pin Functions Port 7 pins are also used for A/D converter analog input (AN7 to AN0). In the H8/3567 Group, the port 7 pins (P70 to P73) are also used for A/D converter analog input (AN0 to AN3). Rev. 3.00 Mar 17, 2006 page 207 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.9 Port C [H8/3567 Group Version with On-Chip USB Only] 8.9.1 Overview Port C is an 8-bit I/O port. Port C is provided only in the H8/3567 Group version with an on-chip USB. Port C is also used for input/output to control the USB hub downstream port power supply IC. Figure 8.8 shows the port C pin configuration. PC7 (input/output) / OCP5 (input) PC6 (input/output) / OCP4 (input) PC5 (input/output) / OCP3 (input) PC4 (input/output) / OCP2 (input) Port C PC3 (input/output) / ENP5 (output) PC2 (input/output) / ENP4 (output) PC1 (input/output) / ENP3 (output) PC0 (input/output) / ENP2 (output) Figure 8.8 Port C Pin Functions 8.9.2 Register Configuration Table 8.17 shows the port C register configuration. Table 8.17 Port C Registers Name Abbreviation R/W Initial Value Address* Port C data direction register PCDDR W H'00 H'FE4E Port C output data register PCODR R/W H'00 H'FE4C Port C input data register PCPIN R Undefined H'FE4E Note: * PCPIN and PCDDR have the same address. Rev. 3.00 Mar 17, 2006 page 208 of 706 REJ09B0303-0300 Section 8 I/O Ports Port C Data Direction Register (PCDDR) Bit 7 6 5 4 3 2 1 0 PC7DDR PC6DDR PC5DDR PC4DDR PC3DDR PC2DDR PC1DDR PC0DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W PCDDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port C. PCDDR cannot be read; if it is, an undefined value will be returned. Setting a PCDDR bit to 1 makes the corresponding port C pin an output port, while clearing the bit to 0 makes the pin an input port. PCDDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port C Data Output Register (PCODR) Bit 7 6 5 4 3 2 1 0 PC7ODR PC6ODR PC5ODR PC4ODR PC3ODR PC2ODR PC1ODR PC0ODR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W PCODR is an 8-bit readable/writable register that stores output data for the port C pins (PC7 to PC0). PCODR can be read and written to at all times, regardless of the contents of PCDDR. PCODR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port C Input Data Register (PCPIN) Bit 7 6 5 4 3 2 1 0 PC7PIN PC6PIN PC5PIN PC4PIN PC3PIN PC2PIN PC1PIN PC0PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Note: * Determined by the state of pins PC7 to PC0. When a PCPIN read is performed, the pin states are always read. Rev. 3.00 Mar 17, 2006 page 209 of 706 REJ09B0303-0300 Section 8 I/O Ports PCPIN and PCDDR have the same address. When a write is performed, data is written to PCDDR and the port C setting changes. 8.9.3 Pin Functions Port C pins PC7 to PC4 are also used as input pins (OCP5 to OCP2) that receive overcurrent detection signals (overcurrent signals) output from the USB hub downstream port power supply IC. Port C pins PC3 to PC0 are also used as output pins (ENP5 to ENP2) for power supply output enable signals (enable signals) input to the USB hub downstream port power supply IC. The power supply IC control pin function can be enabled or disabled for each OCP/ENP pair by means of bits 3 to 0 (HOC5E to HOC2E) in the USB’s HOCCR register. When the power supply IC control pin function is disabled, port C is used as an I/O port, with input or output specifiable individually for each pin. Setting a PCDDR bit to 1 makes the corresponding port C pin an output port, while clearing the bit to 0 makes the pin an input port. Rev. 3.00 Mar 17, 2006 page 210 of 706 REJ09B0303-0300 Section 8 I/O Ports 8.10 Port D [H8/3567 Group Version with On-Chip USB Only] 8.10.1 Overview Port D is an 8-bit I/O port. Port D is provided only in the H8/3567 Group version with an on-chip USB. Port D is also used for USB hub downstream data input/output. Port D input/output characteristics are prescribed by the USB bus driver/receiver power supply (DrVCC) voltage. Figure 8.9 shows the port D pin configuration. PD7 (input/output) / DS5D− (input/output) PD6 (input/output) / DS5D+ (input/output) PD5 (input/output) / DS4D− (input/output) PD4 (input/output) / DS4D+ (input/output) Port D PD3 (input/output) / DS3D− (input/output) PD2 (input/output) / DS3D+ (input/output) PD1 (input/output) / DS2D− (input/output) PD0 (input/output) / DS2D+ (input/output) Figure 8.9 Port D Pin Functions 8.10.2 Register Configuration Table 8.18 shows the port D register configuration. Table 8.18 Port D Registers Name Abbreviation R/W Initial Value Address* Port D data direction register PDDDR W H'00 H'FE4F Port D output data register PDODR R/W H'00 H'FE4D Port D input data register PDPIN R Undefined H'FE4F Note: * PDPIN and PDDDR have the same address. Rev. 3.00 Mar 17, 2006 page 211 of 706 REJ09B0303-0300 Section 8 I/O Ports Port D Data Direction Register (PDDDR) Bit 7 6 5 4 3 2 1 0 PD7DDR PD6DDR PD5DDR PD4DDR PD3DDR PD2DDR PD1DDR PD0DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W PDDDR is an 8-bit write-only register, the individual bits of which specify input or output for the pins of port D. PDDDR cannot be read; if it is, an undefined value will be returned. Setting a PDDDR bit to 1 makes the corresponding port D pin an output port, while clearing the bit to 0 makes the pin an input port. PDDDR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port D Data Output Register (PDODR) Bit 7 6 5 4 3 2 1 0 PD7ODR PD6ODR PD5ODR PD4ODR PD3ODR PD2ODR PD1ODR PD0ODR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W PDODR is an 8-bit readable/writable register that stores output data for the port D pins (PD7 to PD0). PDODR can be read and written to at all times, regardless of the contents of PDDDR. PDODR is initialized to H'00 by a reset and in hardware standby mode. It retains its previous state in software standby mode. Port D Input Data Register (PDPIN) Bit 7 6 5 4 3 2 1 0 PD7PIN PD6PIN PD5PIN PD4PIN PD3PIN PD2PIN PD1PIN PD0PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Note: * Determined by the state of pins PD7 to PD0. When a PDPIN read is performed, the pin states are always read. Rev. 3.00 Mar 17, 2006 page 212 of 706 REJ09B0303-0300 Section 8 I/O Ports PDPIN and PDDDR have the same address. When a write is performed, data is written to PDDDR and the port D setting changes. 8.10.3 Pin Functions Port D pins are also used for USB hub downstream data input/output. When the FONLY bit is cleared to 1 in the USBCR register, port D is used as an I/O port, with input or output specifiable individually for each pin. Setting a PDDDR bit to 1 makes the corresponding port D pin an output port, while clearing the bit to 0 makes the pin an input port. When the FONLY bit is cleared to 0, port D is used for USB hub downstream data input/output. The USB provided in the H8/3567 Group has a built-in bus driver/receiver, and port D operates on the bus driver/receiver power supply (DrVCC) regardless of the setting of the FONLY bit. Therefore, Port D input/output characteristics are prescribed by the DrVCC voltage. Rev. 3.00 Mar 17, 2006 page 213 of 706 REJ09B0303-0300 Section 8 I/O Ports Rev. 3.00 Mar 17, 2006 page 214 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers Section 9 8-Bit PWM Timers 9.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip PWM (pulse width modulation) timer, with sixteen (H8/3577 Group) or eight (H8/3567 Group) outputs. Sixteen output waveforms are generated from a common time base, enabling PWM output with a high carrier frequency to be produced using pulse division. The PWM timer module has sixteen 8-bit PWM data registers (PWDRs), and an output pulse with a duty cycle of 0 to 100% can be obtained as specified by PWDR and the port data register (P1DR or P2DR). 9.1.1 Features The PWM timer module has the following features. • Operable at a maximum carrier frequency of 1.25 MHz using pulse division (at 20 MHz operation) • Duty cycles from 0 to 100% with 1/256 resolution (100% duty realized by port output) • Direct or inverted PWM output, and PWM output enable/disable control Rev. 3.00 Mar 17, 2006 page 215 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.1.2 Block Diagram Figure 9.1 shows a block diagram of the PWM timer module. PWDR0 P11/PW1 Comparator 1 PWDR1 P12/PW2 Comparator 2 PWDR2 P13/PW3 Comparator 3 PWDR3 P14/PW4 Comparator 4 PWDR4 Comparator 5 PWDR5 Comparator 6 PWDR6 Comparator 7 PWDR7 Comparator 8 PWDR8 P15/PW5 P16/PW6 P17/PW7 P20/PW8 P21/PW9 P22/PW10 H8/3577 Group only Comparator 9 PWDR9 Comparator 10 PWDR10 Comparator 11 PWDR11 P24/PW12 Comparator 12 PWDR12 P25/PW13 Comparator 13 PWDR13 P26/PW14 Comparator 14 PWDR14 P27/PW15 Comparator 15 PWDR15 TCNT Clock selection P23/PW11 PWDPRB PWDPRA PWOERB PWOERA P2DDR P1DDR P2DR P1DR Legend: PWSL: PWDR: PWDPRA: PWDPRB: PWOERA: PWOERB: PCSR: P1DDR: P2DDR: P1DR: P2DR: PWM register select PWM data register PWM data polarity register A PWM data polarity register B PWM output enable register A PWM output enable register B Peripheral clock select register Port 1 data direction register Port 2 data direction register Port 1 data register Port 2 data register φ/16 φ/8 φ/4 φ/2 φ Internal clock Figure 9.1 Block Diagram of PWM Timer Module Rev. 3.00 Mar 17, 2006 page 216 of 706 REJ09B0303-0300 Module data bus Bus interface Comparator 0 Port/PWM output control P10/PW0 PWSL PCSR Internal data bus Section 9 8-Bit PWM Timers 9.1.3 Pin Configuration Table 9.1 shows the PWM output pin. Table 9.1 Pin Configuration Name Abbreviation I/O Function PWM output pin 0 to 7 PW0 to PW7 Output PWM timer pulse output 0 to 7 PWM output pin 8 to 15 PW8 to PW15 Output PWM timer pulse output 8 to 15 (H8/3577 Group only) 9.1.4 Register Configuration Table 9.2 lists the registers of the PWM timer module. Table 9.2 PWM Timer Module Registers Name Abbreviation R/W Initial Value Address PWM register select PWSL R/W H'20 H'FFD6 PWM data registers 0 to 15 PWDR0 to PWDR15 R/W H'00 H'FFD7 PWM data polarity register A PWDPRA R/W H'00 H'FFD5 PWM data polarity register B PWDPRB R/W H'00 H'FFD4 PWM output enable register A PWOERA R/W H'00 H'FFD3 PWM output enable register B PWOERB R/W H'00 H'FFD2 Port 1 data direction register P1DDR W H'00 H'FFB0 Port 2 data direction register P2DDR W H'00 H'FFB1 Port 1 data register P1DR R/W H'00 H'FFB2 Port 2 data register P2DR R/W H'00 H'FFB3 Peripheral clock select register PCSR R/W H'00 H'FF82 Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 Rev. 3.00 Mar 17, 2006 page 217 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.2 Register Descriptions 9.2.1 PWM Register Select (PWSL) Bit 7 6 5 4 3 2 1 0 PWCKE PWCKS — — RS3 RS2 RS1 RS0 Initial value 0 0 1 0 0 0 0 0 Read/Write R/W R/W — — R/W R/W R/W R/W PWSL is an 8-bit readable/writable register used to select the PWM timer input clock and the PWM data register. PWSL is initialized to H'20 by a reset, and in the standby modes, and module stop mode. Bits 7 and 6—PWM Clock Enable, PWM Clock Select (PWCKE, PWCKS): These bits, together with bits PWCKA and PWCKB in PCSR, select the internal clock input to TCNT in the PWM timer. PWSL PCSR Bit 7 Bit 6 Bit 2 Bit 1 PWCKE PWCKS PWCKB PWCKA Description 0 — — — Clock input is disabled 1 0 — — φ (system clock) is selected 1 0 0 φ/2 is selected 1 φ/4 is selected 0 φ/8 is selected 1 φ/16 is selected 1 (Initial value) The PWM resolution, PWM conversion period, and carrier frequency depend on the selected internal clock, and can be found from the following equations. Resolution (minimum pulse width) = 1/internal clock frequency PWM conversion period = resolution × 256 Carrier frequency = 16/PWM conversion period Thus, with a 20 MHz system clock (φ), the resolution, PWM conversion period, and carrier frequency are as shown below. Rev. 3.00 Mar 17, 2006 page 218 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers Resolution, PWM Conversion Period, and Carrier Frequency when φ = 20 MHz Table 9.3 Internal Clock Frequency Resolution PWM Conversion Period Carrier Frequency φ 50 ns 12.8 µs 1250 kHz φ/2 100 ns 25.6 µs 625 kHz φ/4 200 ns 51.2 µs 312.5 kHz φ/8 400 ns 102.4 µs 156.3 kHz φ/16 800 ns 204.8 µs 78.1 kHz Bit 5—Reserved: This bit is always read as 1 and cannot be modified. Bit 4—Reserved: This bit is always read as 0 and cannot be modified. Bits 3 to 0—Register Select (RS3 to RS0): These bits select the PWM data register. Bit 3 Bit 2 Bit 1 Bit 0 RS3 RS2 RS1 RS0 Register Selection 0 0 0 0 PWDR0 selected 1 PWDR1 selected 1 1 0 1 1 0 0 1 1 0 1 0 PWDR2 selected 1 PWDR3 selected 0 PWDR4 selected 1 PWDR5 selected 0 PWDR6 selected 1 PWDR7 selected 0 PWDR8 selected 1 PWDR9 selected 0 PWDR10 selected 1 PWDR11 selected 0 PWDR12 selected 1 PWDR13 selected 0 PWDR14 selected 1 PWDR15 selected Rev. 3.00 Mar 17, 2006 page 219 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.2.2 PWM Data Registers (PWDR0 to PWDR15) Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Each PWDR is an 8-bit readable/writable register that specifies the duty cycle of the basic pulse to be output, and the number of additional pulses. The value set in PWDR corresponds to a 0 or 1 ratio in the conversion period. The upper 4 bits specify the duty cycle of the basic pulse as 0/16 to 15/16 with a resolution of 1/16. The lower 4 bits specify how many extra pulses are to be added within the conversion period comprising 16 basic pulses. Thus, a specification of 0/256 to 255/256 is possible for 0/1 ratios within the conversion period. For 256/256 (100%) output, port output should be used. PWDR is initialized to H'00 by a reset, and in the standby modes, and module stop mode. 9.2.3 PWM Data Polarity Registers A and B (PWDPRA and PWDPRB) PWDPRA Bit 7 6 5 4 3 2 1 0 OS7 OS6 OS5 OS4 OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 OS15 OS14 OS13 OS12 OS11 OS10 OS9 OS8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W PWDPRB Bit Each PWDPR is an 8-bit readable/writable register that controls the polarity of the PWM output. Bits OS0 to OS15 correspond to outputs PW0 to PW15. Rev. 3.00 Mar 17, 2006 page 220 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers PWDPR is initialized to H'00 by a reset and in hardware standby mode. OS Description 0 PWM direct output (PWDR value corresponds to high width of output) 1 PWM inverted output (PWDR value corresponds to low width of output) 9.2.4 PWM Output Enable Registers A and B (PWOERA and PWOERB) (Initial value) PWOERA Bit 7 6 5 4 3 2 1 0 OE7 OE6 OE5 OE4 OE3 OE2 OE1 OE0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 OE15 OE14 OE13 OE12 OE11 OE10 OE9 OE8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W PWOERB Bit Each PWOER is an 8-bit readable/writable register that switches between PWM output and port output. Bits OE15 to OE0 correspond to outputs PW15 to PW0. To set a pin in the output state, a setting in the port direction register is also necessary. Bits P17DDR to P10DDR correspond to outputs PW7 to PW0, and bits P27DDR to P20DDR correspond to outputs PW15 to PW8. PWOER is initialized to H'00 by a reset and in hardware standby mode. DDR OE Description 0 0 Port input 1 Port input 0 Port output or PWM 256/256 output 1 PWM output (0 to 255/256 output) 1 (Initial value) Rev. 3.00 Mar 17, 2006 page 221 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.2.5 Peripheral Clock Select Register (PCSR) Bit 7 6 5 4 3 2 1 0 — — — — — PWCKB PWCKA — Initial value 0 0 0 0 0 0 0 0 Read/Write — — — — — R/W R/W R/W PCSR is an 8-bit readable/writable register that selects the PWM timer input clock. PCSR is initialized to H'00 by a reset, and in hardware standby mode. Bits 7 to 3—Reserved: These bits cannot be modified and are always read as 0. Bits 2 and 1—PWM Clock Select (PWCKB, PWCKA): Together with bits PWCKE and PWCKS in PWSL, these bits select the internal clock input to TCNT in the PWM timer. For details, see section 9.2.1, PWM Register Select (PWSL). Bit 0—Reserved: Do not set this bit to 1. 9.2.6 Port 1 Data Direction Register (P1DDR) Bit 7 6 5 4 3 2 1 0 P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR P11DDR P10DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P1DDR is an 8-bit write-only register that specifies the input/output direction and PWM output for each pin of port 1 on a bit-by-bit basis. Port 1 pins are multiplexed with pins PW0 to PW7. The bit corresponding to a pin to be used for PWM output should be set to 1. For details on P1DDR, see section 8.2, Port 1. Rev. 3.00 Mar 17, 2006 page 222 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.2.7 Port 2 Data Direction Register (P2DDR) Bit 7 6 5 4 3 2 1 0 P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR P21DDR P20DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W P2DDR is an 8-bit write-only register that specifies the input/output direction and PWM output for each pin of port J on a bit-by-bit basis. Port 2 pins are multiplexed with pins PW8 to PW15. The bit corresponding to a pin to be used for PWM output should be set to 1. For details on P2DDR, see section 8.3, Port 2. 9.2.8 Port 1 Data Register (P1DR) Bit 7 6 5 4 3 2 1 0 P17DR P16DR P15DR P14DR P13DR P12DR P11DR P10DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P1DR is an 8-bit readable/writable register used to fix PWM output at 1 (when OS = 0) or 0 (when OS = 1). For details on P1DR, see section 8.2, Port 1. 9.2.9 Port 2 Data Register (P2DR) Bit 7 6 5 4 3 2 1 0 P27DR P26DR P25DR P24DR P23DR P22DR P21DR P20DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P2DR is an 8-bit readable/writable register used to fix PWM output at 1 (when OS = 0) or 0 (when OS = 1). For details on P2DR, see section 8.3, Port 2. Rev. 3.00 Mar 17, 2006 page 223 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers 9.2.10 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers, and is used to perform module stop mode control. When the MSTP11 bit is set to 1, 8-bit PWM timer operation is halted and a transition is made to module stop mode. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 3—Module Stop (MSTP11): Specifies PWM module stop mode. MSTPCRH Bit 3 MSTP11 Description 0 PWM module stop mode is cleared 1 PWM module stop mode is set Rev. 3.00 Mar 17, 2006 page 224 of 706 REJ09B0303-0300 (Initial value) Section 9 8-Bit PWM Timers 9.3 Operation 9.3.1 Correspondence between PWM Data Register Contents and Output Waveform The upper 4 bits of PWDR specify the duty cycle of the basic pulse as 0/16 to 15/16 with a resolution of 1/16, as shown in table 9.4. Table 9.4 Upper 6 Bits 0000 Duty Cycle of Basic Pulse Basic Pulse Waveform (Internal) 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Rev. 3.00 Mar 17, 2006 page 225 of 706 REJ09B0303-0300 Section 9 8-Bit PWM Timers The lower 4 bits of PWDR specify the position of pulses added to the 16 basic pulses, as shown in table 9.5. An additional pulse consists of a high period (when OS = 0) with a width equal to the resolution, added before the rising edge of a basic pulse. When the upper 4 bits of PWDR are 0000, there is no rising edge of the basic pulse, but the timing for adding pulses is the same. Table 9.5 Position of Pulses Added to Basic Pulses Basic Pulse No. Lower 4 Bits 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0000 0001 Yes 0010 Yes 0011 Yes Yes Yes Yes Yes Yes 0100 Yes Yes 0101 Yes Yes Yes Yes Yes 0110 Yes Yes Yes Yes Yes Yes 0111 Yes Yes Yes Yes Yes Yes Yes Yes 1000 Yes Yes Yes Yes Yes Yes Yes 1001 Yes Yes Yes Yes Yes Yes Yes Yes Yes 1010 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1011 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1100 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1101 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1110 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1111 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No additional pulse Resolution width Additional pulse provided Additional pulse Figure 9.2 Example of Additional Pulse Timing (When Upper 4 Bits of PWDR = 1000) Rev. 3.00 Mar 17, 2006 page 226 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Section 10 14-Bit PWM Timer 10.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip 14-bit PWM (pulse width modulator) with two output channels. Each channel can be connected to an external low-pass filter to operate as a 14-bit D/A converter. Both channels share the same counter (DACNT) and control register (DACR). 10.1.1 Features The features of the 14-bit PWM D/A are listed below. • The pulse is subdivided into multiple base cycles to reduce ripple. • Two resolution settings and two base cycle settings are available The resolution can be set equal to one or two system clock cycles. The base cycle can be set equal to T × 64 or T × 256, where T is the resolution. • Four operating rates The two resolution settings and two base cycle settings combine to give a selection of four operating rates. Rev. 3.00 Mar 17, 2006 page 227 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer 10.1.2 Block Diagram Figure 10.1 shows a block diagram of the PWM D/A module. Internal clock φ Internal data bus φ/2 Clock Clock selection Bus interface Basic cycle compare-match A PWX0 Fine-adjustment pulse addition A PWX1 Basic cycle compare-match B Fine-adjustment pulse addition B Comparator A DADRA Comparator B DADRB Control logic Basic cycle overflow DACNT DACR Module data bus Legend: DACR: DADRA: DADRB: DACNT: PWM D/A control register ( 6 bits) PWM D/A data register A (15 bits) PWM D/A data register B (15 bits) PWM D/A counter (14 bits) Figure 10.1 PWM D/A Block Diagram Rev. 3.00 Mar 17, 2006 page 228 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer 10.1.3 Pin Configuration Table 10.1 lists the pins used by the PWM D/A module. Table 10.1 Input and Output Pins Channel Name Abbr. I/O Function A PWM output pin 0 PWX0 Output PWM output, channel A B PWM output pin 1 PWX1 Output PWM output, channel B 10.1.4 Register Configuration Table 10.2 lists the registers of the PWM D/A module. Table 10.2 Register Configuration Name Abbreviation R/W Initial value Address PWM D/A control register DACR R/W H'30 PWM D/A data register A high DADRAH R/W H'FF H'FFA0* H'FFA0* PWM D/A data register A low DADRAL R/W H'FF PWM D/A data register B high DADRBH R/W H'FF PWM D/A data register B low DADRBL R/W H'FF PWM D/A counter high DACNTH R/W H'00 H'FFA7* H'FFA6* PWM D/A counter low DACNTL R/W H'03 H'FFA7* Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 Note: * H'FFA1* H'FFA6* The registers of the 14-bit PWM timer are assigned to the same addresses as other registers. Selection of each register is performed by the IICE bit of the serial timer control register (STCR). Also, the same addresses are shared by DADRAH and DACR, and by DADRB and DACNT. Switching is performed by the REGS bit in DACNT or DADRB. Rev. 3.00 Mar 17, 2006 page 229 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer 10.2 Register Descriptions 10.2.1 PWM D/A Counter (DACNT) DACNTH DACNTL Bit (CPU) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit (Counter) 7 6 5 4 3 2 1 0 8 9 10 11 12 13 — — Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 — REGS Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 1 1 — R/W DACNT is a 14-bit readable/writable up-counter that increments on an input clock pulse. The input clock is selected by the clock select bit (CKS) in DACR. The CPU can read and write the DACNT value, but since DACNT is a 16-bit register, data transfers between it and the CPU are performed using a temporary register (TEMP). See section 10.3, Bus Master Interface, for details. DACNT functions as the time base for both PWM D/A channels. When a channel operates with 14-bit precision, it uses all DACNT bits. When a channel operates with 12-bit precision, it uses the lower 12 (counter) bits and ignores the upper two (counter) bits. DACNT is initialized to H'0003 by a reset, in the standby modes, and module stop mode, and by the PWME bit. Bit 1 of DACNTL (CPU) is not used, and is always read as 1. DACNTL Bit 0—Register Select (REGS): DADRA and DACR, and DADRB and DACNT, are located at the same addresses. The REGS bit specifies which registers can be accessed. The REGS bit can be accessed regardless of whether DADRB or DACNT is selected. Bit 0 REGS Description 0 DADRA and DADRB can be accessed 1 DACR and DACNT can be accessed Rev. 3.00 Mar 17, 2006 page 230 of 706 REJ09B0303-0300 (Initial value) Section 10 14-Bit PWM Timer 10.2.2 D/A Data Registers A and B (DADRA and DADRB) DADRH DADRL Bit (CPU) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit (Data) 13 12 11 10 9 8 7 6 5 4 3 2 1 0 — — DADRA Initial value DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CFS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 — 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W DADRB DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CFS REGS Initial value Read/Write 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 — 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W There are two 16-bit readable/writable D/A data registers: DADRA and DADRB. DADRA corresponds to PWM D/A channel A, and DADRB to PWM D/A channel B. The CPU can read and write the PWM D/A data register values, but since DADRA and DADRB are 16-bit registers, data transfers between them and the CPU are performed using a temporary register (TEMP). See section 10.3, Bus Master Interface, for details. The least significant (CPU) bit of DADRA is not used and is always read as 1. DADR is initialized to H'FFFF by a reset, and in the standby modes, and module stop mode. Bits 15 to 2—PWM D/A Data 13 to 0 (DA13 to DA0): The digital value to be converted to an analog value is set in the upper 14 bits of the PWM D/A data register. In each base cycle, the DACNT value is continually compared with these upper 14 bits to determine the duty cycle of the output waveform, and to decide whether to output a fineadjustment pulse equal in width to the resolution. To enable this operation, the data register must be set within a range that depends on the carrier frequency select bit (CFS). If the DADR value is outside this range, the PWM output is held constant. A channel can be operated with 12-bit precision by keeping the two lowest data bits (DA0 and DA1) cleared to 0 and writing the data to be converted in the upper 12 bits. The two lowest data bits correspond to the two highest counter (DACNT) bits. Rev. 3.00 Mar 17, 2006 page 231 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Bit 1—Carrier Frequency Select (CFS) Bit 1 CFS Description 0 Base cycle = resolution (T) × 64 DADR range = H'0401 to H'FFFD 1 Base cycle = resolution (T) × 256 DADR range = H'0103 to H'FFFF (Initial value) DADRA Bit 0—Reserved: This bit cannot be modified and is always read as 1. DADRB Bit 0—Register Select (REGS): DADRA and DACR, and DADRB and DACNT, are located at the same addresses. The REGS bit specifies which registers can be accessed. The REGS bit can be accessed regardless of whether DADRB or DACNT is selected. Bit 0 REGS Description 0 DADRA and DADRB can be accessed 1 DACR and DACNT can be accessed 10.2.3 (Initial value) PWM D/A Control Register (DACR) Bit 7 6 5 4 3 2 1 0 TEST PWME — — OEB OEA OS CKS Initial value 0 0 1 1 0 0 0 0 Read/Write R/W R/W — — R/W R/W R/W R/W DACR is an 8-bit readable/writable register that selects test mode, enables the PWM outputs, and selects the output phase and operating speed. DACR is initialized to H'30 by a reset, and in the standby modes, and module stop mode. Bit 7—Test Mode (TEST): Selects test mode, which is used in testing the chip. Normally this bit should be cleared to 0. Rev. 3.00 Mar 17, 2006 page 232 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Bit 7 TEST Description 0 PWM (D/A) in user state: normal operation 1 PWM (D/A) in test state: correct conversion results unobtainable (Initial value) Bit 6—PWM Enable (PWME): Starts or stops the PWM D/A counter (DACNT). Bit 6 PWME Description 0 DACNT operates as a 14-bit up-counter 1 DACNT halts at H'0003 (Initial value) Bits 5 and 4—Reserved: These bits cannot be modified and are always read as 1. Bit 3—Output Enable B (OEB): Enables or disables output on PWM D/A channel B. Bit 3 OEB Description 0 PWM (D/A) channel B output (at the PWX1 pin) is disabled 1 PWM (D/A) channel B output (at the PWX1 pin) is enabled (Initial value) Bit 2—Output Enable A (OEA): Enables or disables output on PWM D/A channel A. Bit 2 OEA Description 0 PWM (D/A) channel A output (at the PWX0 pin) is disabled 1 PWM (D/A) channel A output (at the PWX0 pin) is enabled (Initial value) Bit 1—Output Select (OS): Selects the phase of the PWM D/A output. Bit 1 OS Description 0 Direct PWM output 1 Inverted PWM output (Initial value) Rev. 3.00 Mar 17, 2006 page 233 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Bit 0—Clock Select (CKS): Selects the PWM D/A resolution. If the system clock (φ) frequency is 10 MHz, resolutions of 100 ns and 200 ns can be selected. Bit 0 CKS Description 0 Operates at resolution (T) = system clock cycle time (tcyc) 1 Operates at resolution (T) = system clock cycle time (tcyc) × 2 10.2.4 (Initial value) Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers, and is used to perform module stop mode control. When the MSTP11 bit is set to 1, 14-bit PWM timer operation is halted and a transition is made to module stop mode. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 3—Module Stop (MSTP11): Specifies PWMX module stop mode. MSTPCRH Bit 3 MSTP11 Description 0 PWMX module stop mode is cleared 1 PWMX module stop mode is set Rev. 3.00 Mar 17, 2006 page 234 of 706 REJ09B0303-0300 (Initial value) Section 10 14-Bit PWM Timer 10.3 Bus Master Interface DACNT, DADRA, and DADRB are 16-bit registers. The data bus linking the bus master and the on-chip supporting modules, however, is only 8 bits wide. When the bus master accesses these registers, it therefore uses an 8-bit temporary register (TEMP). These registers are written and read as follows (taking the example of the CPU interface). • Write When the upper byte is written, the upper-byte write data is stored in TEMP. Next, when the lower byte is written, the lower-byte write data and TEMP value are combined, and the combined 16-bit value is written in the register. • Read When the upper byte is read, the upper-byte value is transferred to the CPU and the lower-byte value is transferred to TEMP. Next, when the lower byte is read, the lower-byte value in TEMP is transferred to the CPU. These registers should always be accessed 16 bits at a time (by word access or two consecutive byte accesses), and the upper byte should always be accessed before the lower byte. Correct data will not be transferred if only the upper byte or only the lower byte is accessed. Figure 10.2 shows the data flow for access to DACNT. The other registers are accessed similarly. Example 1: Write to DACNT MOV.W R0, @DACNT ; Write R0 contents to DACNT Example 2: Read DADRA MOV.W @DADRA, R0 ; Copy contents of DADRA to R0 Table 10.3 Read and Write Access Methods for 16-Bit Registers Read Write Register Name Word Byte Word Byte DADRA and DADRB Yes Yes Yes × DACNT Yes × Yes × Notes: Yes: Permitted type of access. Word access includes successive byte accesses to the upper byte (first) and lower byte (second). ×: This type of access may give incorrect results. Rev. 3.00 Mar 17, 2006 page 235 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Upper-Byte Write CPU (H'AA) Upper byte Module data bus Bus interface TEMP (H'AA) DACNTH ( ) DACNTL ( ) Lower-Byte Write CPU (H'57) Lower byte Module data bus Bus interface TEMP (H'AA) DACNTH (H'AA) DACNTL (H'57) Figure 10.2 (a) Access to DACNT (CPU Writes H'AA57 to DACNT) Rev. 3.00 Mar 17, 2006 page 236 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Upper-Byte Read CPU (H'AA) Upper byte Module data bus Bus interface TEMP (H'57) DACNTH (H'AA) DACNTL (H'57) Lower-Byte Read CPU (H'57) Lower byte Module data bus Bus interface TEMP (H'57) DACNTH ( ) DACNTL ( ) Figure 10.2 (b) Access to DACNT (CPU Reads H'AA57 from DACNT) Rev. 3.00 Mar 17, 2006 page 237 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer 10.4 Operation A PWM waveform like the one shown in figure 10.3 is output from the PWMX pin. When OS = 0, the value in DADR corresponds to the total width (TL) of the low (0) pulses output in one conversion cycle (256 pulses when CFS = 0, 64 pulses when CFS = 1). When OS = 1, the output waveform is inverted and the DADR value corresponds to the total width (TH) of the high (1) output pulses. Figure 10.4 shows the types of waveform output available. 1 conversion cycle (T × 214 (= 16384)) tf Basic cycle (T × 64 or T × 256) tL T: Resolution m TL = ∑ tLn (when OS = 0) n=1 (When CFS = 0, m = 256; when CFS = 1, m = 64) Figure 10.3 PWM D/A Operation Table 10.4 summarizes the relationships of the CKS, CFS, and OS bit settings to the resolution, base cycle, and conversion cycle. The PWM output remains flat unless DADR contains at least a certain minimum value. Table 10.4 indicates the range of DADR settings that give an output waveform like the one in figure 10.3, and lists the conversion cycle length when low-order DADR bits are kept cleared to 0, reducing the conversion precision to 12 bits or 10 bits. Rev. 3.00 Mar 17, 2006 page 238 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Table 10.4 Settings and Operation (Examples when φ = 10 MHz) Resolution Base Conversion T Cycle CKS CFS Cycle (µs) (µs) (µs) 0 0.1 0 6.4 1638.4 Fixed DADR Bits TL (if OS = 0) TH (if OS = 1) 1. Always low (or high) (DADR = H'0001 to H'03FD) 2. (Data value) × T (DADR = H'0401 to H'FFFD) 1 25.6 1638.4 1. Always low (or high) (DADR = H'0003 to H'00FF) 2. (Data value) × T (DADR = H'0103 to H'FFFF) 1 0.2 0 12.8 3276.8 1. Always low (or high) (DADR = H'0001 to H'03FD) 2. (Data value) × T (DADR = H'0401 to H'FFFD) 1 51.2 3276.8 1. Always low (or high) (DADR = H'0003 to H'00FF) 2. (Data value) × T (DADR = H'0103 to H'FFFF) Note: * Bit Data Precision (Bits) 3 2 1 0 Conversion Cycle* 14 (µs) 1638.4 12 0 0 409.6 10 0 0 0 0 102.4 14 1638.4 12 0 0 409.6 10 0 0 0 0 102.4 14 3276.8 12 0 0 819.2 10 0 0 0 0 204.8 14 3276.8 12 0 0 819.2 10 0 0 0 0 204.8 This column indicates the conversion cycle when specific DADR bits are fixed. Rev. 3.00 Mar 17, 2006 page 239 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer 1. OS = 0 (DADR corresponds to TL) a. CFS = 0 [base cycle = resolution (T) × 64] 1 conversion cycle tf1 tL1 tf2 tf255 tL2 tL3 tL255 tf256 tL256 tf1 = tf2 = tf3 = · · · = tf255 = tf256 = T × 64 tL1 + tL2 + tL3 + · · · + tL255 + tL256 = TL Figure 10.4 (1) Output Waveform b. CFS = 1 [base cycle = resolution (T) × 256] 1 conversion cycle tf1 tL1 tf2 tL2 tf63 tL3 tL63 tf1 = tf2 = tf3 = · · · = tf63 = tf64 = T × 256 tL1 + tL2 + tL3 + · · · + tL63 + tL64 = TL Figure 10.4 (2) Output Waveform Rev. 3.00 Mar 17, 2006 page 240 of 706 REJ09B0303-0300 tf64 tL64 Section 10 14-Bit PWM Timer 2. OS = 1 (DADR corresponds to TH) a. CFS = 0 [base cycle = resolution (T) × 64] 1 conversion cycle tf1 tH1 tf2 tf255 tH2 tH3 tH255 tf256 tH256 tf1 = tf2 = tf3 = · · · = tf255 = tf256 = T × 64 tH1 + tH2 + tH3 + · · · + tH255 + tH256 = TH Figure 10.4 (3) Output Waveform b. CFS = 1 [base cycle = resolution (T) × 256] 1 conversion cycle tf1 tH1 tf2 tH2 tf63 tH3 tH63 tf64 tH64 tf1 = tf2 = tf3 = · · · = tf63 = tf64 = T × 256 tH1 + tH2 + tH3 + · · · + tH63 + tH64 = TH Figure 10.4 (4) Output Waveform Rev. 3.00 Mar 17, 2006 page 241 of 706 REJ09B0303-0300 Section 10 14-Bit PWM Timer Rev. 3.00 Mar 17, 2006 page 242 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Section 11 16-Bit Free-Running Timer 11.1 Overview The H8/3577 Group and H8/3567 Group have a single-channel on-chip 16-bit free-running timer (FRT). Applications of the FRT module include rectangular-wave output (up to two independent waveforms), input pulse width measurement, and measurement of external clock periods. 11.1.1 Features The features of the free-running timer module are listed below. • Selection of four clock sources The free-running counter can be driven by an internal clock source (φ/2, φ/8, or φ/32), or an external clock input (enabling use as an external event counter). • Two independent comparators Each comparator can generate an independent waveform. • Four input capture channels The current count can be captured on the rising or falling edge (selectable) of an input signal. The four input capture registers can be used separately, or in a buffer mode. • Counter can be cleared under program control The free-running counters can be cleared on compare-match A. • Seven independent interrupts Two compare-match interrupts, four input capture interrupts, and one overflow interrupt can be requested independently. • Special functions provided by automatic addition function The contents of OCRAR and OCRAF can be added to the contents of OCRA automatically, enabling a periodic waveform to be generated without software intervention. The contents of ICRD can be added automatically to the contents of OCRDM × 2, enabling input capture operations in this interval to be restricted. Rev. 3.00 Mar 17, 2006 page 243 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.1.2 Block Diagram Figure 11.1 shows a block diagram of the free-running timer. External clock source Internal clock sources φ/2 φ/8 φ/32 FTCI Clock select OCRA R/F (H/L) + Clock OCRA (H/L) Comparematch A Comparator A FTOA Overflow FTOB Clear Bus interface FRC (H/L) Comparematch B OCRB (H/L) Control logic Input capture FTIA ICRA (H/L) ICRB (H/L) FTIB Internal data bus Module data bus Comparator B ICRC (H/L) FTIC ICRD (H/L) FTID + Comparator M Compare-match M ×1 ×2 OCRDM L TCSR TIER TCR TOCR ICIA ICIB ICIC ICID OCIA OCIB FOVI Legend: OCRA, B: FRC: ICRA, B, C, D: TCSR: Interrupt signals Output compare register A, B (16 bits) Free-running counter (16 bits) Input capture register A, B, C, D (16 bits) Timer control/status register (8 bits) TIER: Timer interrupt enable register (8 bits) TCR: Timer control register (8 bits) TOCR: Timer output compare control register (8 bits) Figure 11.1 Block Diagram of 16-Bit Free-Running Timer Rev. 3.00 Mar 17, 2006 page 244 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.1.3 Input and Output Pins Table 11.1 lists the input and output pins of the free-running timer module. Table 11.1 Input and Output Pins of Free-Running Timer Module Name Abbreviation I/O Function Counter clock input FTCI Input FRC counter clock input Output compare A FTOA Output Output compare A output Output compare B FTOB Output Output compare B output Input capture A FTIA Input Input capture A input Input capture B FTIB Input Input capture B input Input capture C FTIC Input Input capture C input Input capture D FTID Input Input capture D input Rev. 3.00 Mar 17, 2006 page 245 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.1.4 Register Configuration Table 11.2 lists the registers of the free-running timer module. Table 11.2 Register Configuration Name Abbreviation R/W Initial Value Address Timer interrupt enable register TIER R/W H'01 H'FF90 Timer control/status register TCSR R/(W)* H'00 H'FF91 Free-running counter FRC R/W H'0000 H'FF92 Output compare register A OCRA R/W H'FFFF Output compare register B OCRB R/W H'FFFF H'FF94* 2 H'FF94* Timer control register TCR R/W H'00 H'FF96 Timer output compare control register TOCR R/W H'00 H'FF97 Input capture register A ICRA R H'0000 Input capture register B ICRB R H'0000 H'FF98* 3 H'FF9A* Input capture register C ICRC R H'0000 3 H'FF9C* Input capture register D ICRD R H'0000 Output compare register AR OCRAR R/W H'FFFF H'FF9E 3 H'FF98* Output compare register AF OCRAF R/W H'FFFF Output compare register DM OCRDM R/W H'0000 H'FF9A* 3 H'FF9C* Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 1 2 3 3 Notes: 1. Bits 7 to 1 are read-only; only 0 can be written to clear the flags. Bit 0 is readable/writable. 2. OCRA and OCRB share the same address. Access is controlled by the OCRS bit in TOCR. 3. ICRA, ICRB, and ICRC share the same addresses with OCRAR, OCRAF, and OCRDM. Access is controlled by the ICRS bit in TOCR. Rev. 3.00 Mar 17, 2006 page 246 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.2 Register Descriptions 11.2.1 Free-Running Counter (FRC) Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W FRC is a 16-bit readable/writable up-counter that increments on an internal pulse generated from a clock source. The clock source is selected by bits CKS1 and CKS0 in TCR. FRC can also be cleared by compare-match A. When FRC overflows from H'FFFF to H'0000, the overflow flag (OVF) in TCSR is set to 1. FRC is initialized to H'0000 by a reset and in hardware standby mode. 11.2.2 Output Compare Registers A and B (OCRA, OCRB) Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W OCRA and OCRB are 16-bit readable/writable registers, the contents of which are continually compared with the value in the FRC. When a match is detected, the corresponding output compare flags (OCFA or OCFB) is set in TCSR. In addition, if the output enable bit (OEA or OEB) in TOCR is set to 1, when OCR and FRC values match, the logic level selected by the output level bit (OLVLA or OLVLB) in TOCR is output at the output compare pin (FTOA or FTOB). Following a reset, the FTOA and FTOB output levels are 0 until the first compare-match. OCR is initialized to H'FFFF by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 247 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.2.3 Input Capture Registers A to D (ICRA to ICRD) Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R There are four input capture registers, A to D, each of which is a 16-bit read-only register. When the rising or falling edge of the signal at an input capture input pin (FTIA to FTID) is detected, the current FRC value is copied to the corresponding input capture register (ICRA to ICRD). At the same time, the corresponding input capture flag (ICFA to ICFD) in TCSR is set to 1. The input capture edge is selected by the input edge select bits (IEDGA to IEDGD) in TCR. ICRC and ICRD can be used as ICRA and ICRB buffer registers, respectively, and made to perform buffer operations, by means of buffer enable bits A and B (BUFEA, BUFEB) in TCR. Figure 11.2 shows the connections when ICRC is specified as the ICRA buffer register (BUFEA = 1). When ICRC is used as the ICRA buffer, both rising and falling edges can be specified as transitions of the external input signal by setting IEDGA ≠ IEDGC. When IEDGA = IEDGC, either the rising or falling edge is designated. See table 11.3. Note: The FRC contents are transferred to the input capture register regardless of the value of the input capture flag (ICF). IEDGA BUFEA IEDGC FTIA Edge detect and capture signal generating circuit ICRC ICRA Figure 11.2 Input Capture Buffering (Example) Rev. 3.00 Mar 17, 2006 page 248 of 706 REJ09B0303-0300 FRC Section 11 16-Bit Free-Running Timer Table 11.3 Buffered Input Capture Edge Selection (Example) IEDGA IEDGC Description 0 0 Captured on falling edge of input capture A (FTIA) 1 Captured on both rising and falling edges of input capture A (FTIA) 1 (Initial value) 0 1 Captured on rising edge of input capture A (FTIA) To ensure input capture, the width of the input capture pulse should be at least 1.5 system clock periods (φ). When triggering is enabled on both edges, the input capture pulse width should be at least 2.5 system clock periods (φ). ICR is initialized to H'0000 by a reset and in hardware standby mode. 11.2.4 Output Compare Registers AR and AF (OCRAR, OCRAF) Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W OCRAR and OCRAF are 16-bit readable/writable registers. When the OCRAMS bit in TOCR is set to 1, the operation of OCRA is changed to include the use of OCRAR and OCRAF. The contents of OCRAR and OCRAF are automatically added alternately to OCRA, and the result is written to OCRA. The write operation is performed on the occurrence of compare-match A. In the 1st compare-match A after setting the OCRAMS bit to 1, OCRAF is added. The operation due to compare-match A varies according to whether the compare-match follows addition of OCRAR or OCRAF. The value of the OLVLA bit in TOCR is ignored, and 1 is output on a compare-match A following addition of OCRAF, while 0 is output on a compare-match A following addition of OCRAR. When using the OCRA automatic addition function, do not select internal clock φ/2 as the FRC counter input clock together with a set value of H'0001 or less for OCRAR (or OCRAF). OCRAR and OCRAF are initialized to H'FFFF by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 249 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.2.5 Output Compare Register DM (OCRDM) Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W OCRDM is a 16-bit readable/writable register in which the upper 8 bits are fixed at H'00. When the ICRDMS bit in TOCR is set to 1 and the contents of OCRDM are other than H'0000, the operation of ICRD is changed to include the use of OCRDM. The point at which input capture D occurs is taken as the start of a mask interval. Next, twice the contents of OCRDM is added to the contents of ICRD, and the result is compared with the FRC value. The point at which the values match is taken as the end of the mask interval. New input capture D events are disabled during the mask interval. A mask interval is not generated when the ICRDMS bit is set to 1 and the contents of OCRDM are H'0000. OCRDM is initialized to H'0000 by a reset and in hardware standby mode. 11.2.6 Timer Interrupt Enable Register (TIER) Bit 7 6 5 4 3 2 1 0 ICIAE ICIBE ICICE ICIDE OCIAE OCIBE OVIE — Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/W — TIER is an 8-bit readable/writable register that enables and disables interrupts. TIER is initialized to H'01 by a reset and in hardware standby mode. Bit 7—Input Capture Interrupt A Enable (ICIAE): Selects whether to request input capture interrupt A (ICIA) when input capture flag A (ICFA) in TCSR is set to 1. Rev. 3.00 Mar 17, 2006 page 250 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 7 ICIAE Description 0 Input capture interrupt request A (ICIA) is disabled 1 Input capture interrupt request A (ICIA) is enabled (Initial value) Bit 6—Input Capture Interrupt B Enable (ICIBE): Selects whether to request input capture interrupt B (ICIB) when input capture flag B (ICFB) in TCSR is set to 1. Bit 6 ICIBE Description 0 Input capture interrupt request B (ICIB) is disabled 1 Input capture interrupt request B (ICIB) is enabled (Initial value) Bit 5—Input Capture Interrupt C Enable (ICICE): Selects whether to request input capture interrupt C (ICIC) when input capture flag C (ICFC) in TCSR is set to 1. Bit 5 ICICE Description 0 Input capture interrupt request C (ICIC) is disabled 1 Input capture interrupt request C (ICIC) is enabled (Initial value) Bit 4—Input Capture Interrupt D Enable (ICIDE): Selects whether to request input capture interrupt D (ICID) when input capture flag D (ICFD) in TCSR is set to 1. Bit 4 ICIDE Description 0 Input capture interrupt request D (ICID) is disabled 1 Input capture interrupt request D (ICID) is enabled (Initial value) Bit 3—Output Compare Interrupt A Enable (OCIAE): Selects whether to request output compare interrupt A (OCIA) when output compare flag A (OCFA) in TCSR is set to 1. Bit 3 OCIAE Description 0 Output compare interrupt request A (OCIA) is disabled 1 Output compare interrupt request A (OCIA) is enabled (Initial value) Rev. 3.00 Mar 17, 2006 page 251 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 2—Output Compare Interrupt B Enable (OCIBE): Selects whether to request output compare interrupt B (OCIB) when output compare flag B (OCFB) in TCSR is set to 1. Bit 2 OCIBE Description 0 Output compare interrupt request B (OCIB) is disabled 1 Output compare interrupt request B (OCIB) is enabled (Initial value) Bit 1—Timer Overflow Interrupt Enable (OVIE): Selects whether to request a free-running timer overflow interrupt (FOVI) when the timer overflow flag (OVF) in TCSR is set to 1. Bit 1 OVIE Description 0 Timer overflow interrupt request (FOVI) is disabled 1 Timer overflow interrupt request (FOVI) is enabled (Initial value) Bit 0—Reserved: This bit cannot be modified and is always read as 1. 11.2.7 Timer Control/Status Register (TCSR) Bit 7 6 5 4 3 2 1 0 ICFA ICFB ICFC ICFD OCFA OCFB OVF CCLRA Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/W Note: * Only 0 can be written in bits 7 to 1 to clear these flags. TCSR is an 8-bit register used for counter clear selection and control of interrupt request signals. TCSR is initialized to H'00 by a reset and in hardware standby mode. Timing is described in section 11.3, Operation. Bit 7—Input Capture Flag A (ICFA): This status flag indicates that the FRC value has been transferred to ICRA by means of an input capture signal. When BUFEA = 1, ICFA indicates that the old ICRA value has been moved into ICRC and the new FRC value has been transferred to ICRA. ICFA must be cleared by software. It is set by hardware, however, and cannot be set by software. Rev. 3.00 Mar 17, 2006 page 252 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 7 ICFA Description 0 [Clearing condition] (Initial value) Read ICFA when ICFA = 1, then write 0 in ICFA 1 [Setting condition] When an input capture signal causes the FRC value to be transferred to ICRA Bit 6—Input Capture Flag B (ICFB): This status flag indicates that the FRC value has been transferred to ICRB by means of an input capture signal. When BUFEB = 1, ICFB indicates that the old ICRB value has been moved into ICRD and the new FRC value has been transferred to ICRB. ICFB must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 6 ICFB Description 0 [Clearing condition] (Initial value) Read ICFB when ICFB = 1, then write 0 in ICFB 1 [Setting condition] When an input capture signal causes the FRC value to be transferred to ICRB Bit 5—Input Capture Flag C (ICFC): This status flag indicates that the FRC value has been transferred to ICRC by means of an input capture signal. When BUFEA = 1, on occurrence of the signal transition in FTIC (input capture signal) specified by the IEDGC bit, ICFC is set but data is not transferred to ICRC. Therefore, in buffer operation, ICFC can be used as an external interrupt signal (by setting the ICICE bit to 1). ICFC must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 5 ICFC Description 0 [Clearing condition] (Initial value) Read ICFC when ICFC = 1, then write 0 in ICFC 1 [Setting condition] When an input capture signal is received Rev. 3.00 Mar 17, 2006 page 253 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 4—Input Capture Flag D (ICFD): This status flag indicates that the FRC value has been transferred to ICRD by means of an input capture signal. When BUFEB = 1, on occurrence of the signal transition in FTID (input capture signal) specified by the IEDGD bit, ICFD is set but data is not transferred to ICRD. Therefore, in buffer operation, ICFD can be used as an external interrupt by setting the ICIDE bit to 1. ICFD must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 4 ICFD Description 0 [Clearing condition] (Initial value) Read ICFD when ICFD = 1, then write 0 in ICFD 1 [Setting condition] When an input capture signal is received Bit 3—Output Compare Flag A (OCFA): This status flag indicates that the FRC value matches the OCRA value. This flag must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 3 OCFA Description 0 [Clearing condition] (Initial value) Read OCFA when OCFA = 1, then write 0 in OCFA 1 [Setting condition] When FRC = OCRA Bit 2—Output Compare Flag B (OCFB): This status flag indicates that the FRC value matches the OCRB value. This flag must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 2 OCFB Description 0 [Clearing condition] Read OCFB when OCFB = 1, then write 0 in OCFB 1 [Setting condition] When FRC = OCRB Rev. 3.00 Mar 17, 2006 page 254 of 706 REJ09B0303-0300 (Initial value) Section 11 16-Bit Free-Running Timer Bit 1—Timer Overflow Flag (OVF): This status flag indicates that the FRC has overflowed (changed from H'FFFF to H'0000). This flag must be cleared by software. It is set by hardware, however, and cannot be set by software. Bit 1 OVF Description 0 [Clearing condition] (Initial value) Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] When FRC changes from H'FFFF to H'0000 Bit 0—Counter Clear A (CCLRA): This bit selects whether the FRC is to be cleared at comparematch A (when the FRC and OCRA values match). Bit 0 CCLRA Description 0 FRC clearing is disabled 1 FRC is cleared at compare-match A 11.2.8 (Initial value) Timer Control Register (TCR) Bit 7 6 5 4 3 2 1 0 IEDGA IEDGB IEDGC IEDGD BUFEA BUFEB CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCR is an 8-bit readable/writable register that selects the rising or falling edge of the input capture signals, enables the input capture buffer mode, and selects the FRC clock source. TCR is initialized to H'00 by a reset and in hardware standby mode Bit 7—Input Edge Select A (IEDGA): Selects the rising or falling edge of the input capture A signal (FTIA). Rev. 3.00 Mar 17, 2006 page 255 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 7 IEDGA Description 0 Capture on the falling edge of FTIA 1 Capture on the rising edge of FTIA (Initial value) Bit 6—Input Edge Select B (IEDGB): Selects the rising or falling edge of the input capture B signal (FTIB). Bit 6 IEDGB Description 0 Capture on the falling edge of FTIB 1 Capture on the rising edge of FTIB (Initial value) Bit 5—Input Edge Select C (IEDGC): Selects the rising or falling edge of the input capture C signal (FTIC). Bit 5 IEDGC Description 0 Capture on the falling edge of FTIC 1 Capture on the rising edge of FTIC (Initial value) Bit 4—Input Edge Select D (IEDGD): Selects the rising or falling edge of the input capture D signal (FTID). Bit 4 IEDGD Description 0 Capture on the falling edge of FTID 1 Capture on the rising edge of FTID (Initial value) Bit 3—Buffer Enable A (BUFEA): Selects whether ICRC is to be used as a buffer register for ICRA. Bit 3 BUFEA Description 0 ICRC is not used as a buffer register for input capture A 1 ICRC is used as a buffer register for input capture A Rev. 3.00 Mar 17, 2006 page 256 of 706 REJ09B0303-0300 (Initial value) Section 11 16-Bit Free-Running Timer Bit 2—Buffer Enable B (BUFEB): Selects whether ICRD is to be used as a buffer register for ICRB. Bit 2 BUFEB Description 0 ICRD is not used as a buffer register for input capture B 1 ICRD is used as a buffer register for input capture B (Initial value) Bits 1 and 0—Clock Select (CKS1, CKS0): Select external clock input or one of three internal clock sources for the FRC. External clock pulses are counted on the rising edge of signals input to the external clock input pin (FTCI). Bit 1 Bit 0 CKS1 CKS0 Description 0 0 φ/2 internal clock source 1 φ/8 internal clock source 0 φ/32 internal clock source 1 External clock source (rising edge) 1 11.2.9 (Initial value) Timer Output Compare Control Register (TOCR) Bit 7 6 ICRDMS OCRAMS 5 4 3 2 1 0 ICRS OCRS OEA OEB OLVLA OLVLB Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TOCR is an 8-bit readable/writable register that enables output from the output compare pins, selects the output levels, switches access between output compare registers A and B, controls the ICRD and OCRA operating mode, and switches access to input capture registers A, B, and C. TOCR is initialized to H'00 by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 257 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Bit 7—Input Capture D Mode Select (ICRDMS): Specifies whether ICRD is used in the normal operating mode or in the operating mode using OCRDM. Bit 7 ICRDMS Description 0 The normal operating mode is specified for ICRD 1 The operating mode using OCRDM is specified for ICRD (Initial value) Bit 6—Output Compare A Mode Select (OCRAMS): Specifies whether OCRA is used in the normal operating mode or in the operating mode using OCRAR and OCRAF. Bit 6 OCRAMS Description 0 The normal operating mode is specified for OCRA 1 The operating mode using OCRAR and OCRAF is specified for OCRA (Initial value) Bit 5—Input Capture Register Select (ICRS): The same addresses are shared by ICRA and OCRAR, by ICRB and OCRAF, and by ICRC and OCRDM. The ICRS bit determines which registers are selected when the shared addresses are read or written to. The operation of ICRA, ICRB, and ICRC is not affected. Bit 5 ICRS Description 0 The ICRA, ICRB, and ICRC registers are selected 1 The OCRAR, OCRAF, and OCRDM registers are selected (Initial value) Bit 4—Output Compare Register Select (OCRS): OCRA and OCRB share the same address. When this address is accessed, the OCRS bit selects which register is accessed. This bit does not affect the operation of OCRA or OCRB. Bit 4 OCRS Description 0 The OCRA register is selected 1 The OCRB register is selected Rev. 3.00 Mar 17, 2006 page 258 of 706 REJ09B0303-0300 (Initial value) Section 11 16-Bit Free-Running Timer Bit 3—Output Enable A (OEA): Enables or disables output of the output compare A signal (FTOA). Bit 3 OEA Description 0 Output compare A output is disabled 1 Output compare A output is enabled (Initial value) Bit 2—Output Enable B (OEB): Enables or disables output of the output compare B signal (FTOB). Bit 2 OEB Description 0 Output compare B output is disabled 1 Output compare B output is enabled (Initial value) Bit 1—Output Level A (OLVLA): Selects the logic level to be output at the FTOA pin in response to compare-match A (signal indicating a match between the FRC and OCRA values). When the OCRAMS bit is 1, this bit is ignored. Bit 1 OLVLA Description 0 0 output at compare-match A 1 1 output at compare-match A (Initial value) Bit 0—Output Level B (OLVLB): Selects the logic level to be output at the FTOB pin in response to compare-match B (signal indicating a match between the FRC and OCRB values). Bit 0 OLVLB Description 0 0 output at compare-match B 1 1 output at compare-match B (Initial value) Rev. 3.00 Mar 17, 2006 page 259 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.2.10 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR, comprising two 8-bit readable/writable registers, performs module stop mode control. When the MSTP13 bit is set to 1, FRT operation is stopped at the end of the bus cycle, and module stop mode is entered. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 5—Module Stop (MSTP13): Specifies the FRT module stop mode. Bit 5 MSTPCRH Description 0 FRT module stop mode is cleared 1 FRT module stop mode is set 11.3 Operation 11.3.1 FRC Increment Timing (Initial value) FRC increments on a pulse generated once for each period of the selected (internal or external) clock source. Internal Clock: Any of three internal clocks (φ/2, φ/8, or φ/32) created by division of the system clock (φ) can be selected by making the appropriate setting in bits CKS1 and CKS0 in TCR. Figure 11.3 shows the increment timing. Rev. 3.00 Mar 17, 2006 page 260 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer φ Internal clock FRC input clock FRC N–1 N N+1 Figure 11.3 Increment Timing with Internal Clock Source External Clock: If external clock input is selected by bits CKS1 and CKS0 in TCR, FRC increments on the rising edge of the external clock signal. The pulse width of the external clock signal must be at least 1.5 system clock (φ) periods. The counter will not increment correctly if the pulse width is shorter than 1.5 system clock periods. Figure 11.4 shows the increment timing. φ External clock input pin FRC input clock FRC N N+1 Figure 11.4 Increment Timing with External Clock Source Rev. 3.00 Mar 17, 2006 page 261 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.3.2 Output Compare Output Timing When a compare-match occurs, the logic level selected by the output level bit (OLVLA or OLVLB) in TOCR is output at the output compare pin (FTOA or FTOB). Figure 11.5 shows the timing of this operation for compare-match A. φ FRC N OCRA N+1 N N N Compare-match A signal Clear* OLVLA Output compare A output pin FTOA Note: * Vertical arrows ( ) indicate instructions executed by software. Figure 11.5 Timing of Output Compare A Output Rev. 3.00 Mar 17, 2006 page 262 of 706 REJ09B0303-0300 N+1 Section 11 16-Bit Free-Running Timer 11.3.3 FRC Clear Timing FRC can be cleared when compare-match A occurs. Figure 11.6 shows the timing of this operation. φ Compare-match A signal FRC N H'0000 Figure 11.6 Clearing of FRC by Compare-Match A 11.3.4 Input Capture Input Timing Input Capture Input Timing: An internal input capture signal is generated from the rising or falling edge of the signal at the input capture pin, as selected by the corresponding IEDGA to IEDGD bit in TCR. Figure 11.7 shows the usual input capture timing when the rising edge is selected (IEDGA to IEDGD = 1). φ Input capture input pin Input capture signal Figure 11.7 Input Capture Signal Timing (Usual Case) If the upper byte of ICRA to ICRAD is being read when the corresponding input capture signal arrives, the internal input capture signal is delayed by one system clock (φ) period. Figure 11.8 shows the timing for this case. Rev. 3.00 Mar 17, 2006 page 263 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer ICRA to ICRD read cycle T1 T2 T3 φ Input capture input pin Input capture signal Figure 11.8 Input Capture Signal Timing (Input Capture Input when ICRA to ICRD Is Read) Buffered Input Capture Input Timing: ICRC and ICRD can operate as buffers for ICRA and ICRB. Figure 11.9 shows how input capture operates when ICRA and ICRC are used in buffer mode (BUFEA = 1) and IEDGA and IEDGC are set to different values (IEDGA = 0 and IEDGC = 1, or IEDG A = 1 and IEDGC = 0), so that input capture is performed on both the rising and falling edges of FTIA. Rev. 3.00 Mar 17, 2006 page 264 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer φ FTIA Input capture signal FRC n ICRA M ICRC m n+1 N N+1 n n N M M n Figure 11.9 Buffered Input Capture Timing (Usual Case) When ICRC or ICRD is used as a buffer register, its input capture flag is set by the selected transition of its input capture signal. For example, if ICRC is used to buffer ICRA, when the edge transition selected by the IEDGC bit occurs on the FTIC input capture line, ICFC will be set, and if the ICIEC bit is set, an interrupt will be requested. The FRC value will not be transferred to ICRC, however. In buffered input capture, if the upper byte of either of the two registers to which data will be transferred (ICRA and ICRC, or ICRB and ICRD) is being read when the input signal arrives, input capture is delayed by one system clock (φ) period. Figure 11.10 shows the timing when BUFEA = 1. Rev. 3.00 Mar 17, 2006 page 265 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Read cycle: CPU reads ICRA or ICRC T1 T2 T3 φ FTIA Input capture signal Figure 11.10 Buffered Input Capture Timing (Input Capture Input when ICRA or ICRC Is Read) 11.3.5 Timing of Input Capture Flag (ICFA to ICFD) Setting The input capture flag ICFA to ICFD is set to 1 by the internal input capture signal. The FRC value is simultaneously transferred to the corresponding input capture register (ICRx). Figure 11.11 shows the timing of this operation. φ Input capture signal ICFA/B/C/D N FRC ICRA/B/C/D N Figure 11.11 Setting of Input Capture Flag (ICFA to ICFD) Rev. 3.00 Mar 17, 2006 page 266 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.3.6 Setting of Output Compare Flags A and B (OCFA, OCFB) The output compare flags are set to 1 by an internal compare-match signal generated when the FRC value matches the OCRA or OCRB value. This compare-match signal is generated at the last state in which the two values match, just before FRC increments to a new value. Accordingly, when the FRC and OCR values match, the compare-match signal is not generated until the next period of the clock source. Figure 11.12 shows the timing of the setting of OCFA and OCFB. φ FRC N OCRA or OCRB N+1 N Compare-match signal OCFA or OCFB Figure 11.12 Setting of Output Compare Flag (OCFA, OCFB) Rev. 3.00 Mar 17, 2006 page 267 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.3.7 Setting of FRC Overflow Flag (OVF) The FRC overflow flag (OVF) is set to 1 when FRC overflows (changes from H'FFFF to H'0000). Figure 11.13 shows the timing of this operation. φ FRC H'FFFF H'0000 Overflow signal OVF Figure 11.13 Setting of Overflow Flag (OVF) 11.3.8 Automatic Addition of OCRA and OCRAR/OCRAF When the OCRAMS bit in TOCR is set to 1, the contents of OCRAR and OCRAF are automatically added to OCRA alternately, and when an OCRA compare-match occurs a write to OCRA is performed. The OCRA write timing is shown in figure 11.14. φ FRC N N+1 OCRA N N+A OCRAR, OCRAF A Compare-match signal Figure 11.14 OCRA Automatic Addition Timing Rev. 3.00 Mar 17, 2006 page 268 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.3.9 ICRD and OCRDM Mask Signal Generation When the ICRDMS bit in TOCR is set to 1 and the contents of OCRDM are other than H'0000, a signal that masks the ICRD input capture function is generated. The mask signal is set by the input capture signal. The mask signal setting timing is shown in figure 11.15. The mask signal is cleared by the sum of the ICRD contents and twice the OCRDM contents, and an FRC compare-match. The mask signal clearing timing is shown in figure 11.16. φ Input capture signal Input capture mask signal Figure 11.15 Input Capture Mask Signal Setting Timing φ FRC N ICRD + OCRDM × 2 N+1 N Compare-match signal Input capture mask signal Figure 11.16 Input Capture Mask Signal Clearing Timing Rev. 3.00 Mar 17, 2006 page 269 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.4 Interrupts The free-running timer can request seven interrupts (three types): input capture A to D (ICIA, ICIB, ICIC, ICID), output compare A and B (OCIA and OCIB), and overflow (FOVI). Each interrupt can be enabled or disabled by an enable bit in TIER. Independent signals are sent to the interrupt controller for each interrupt. Table 11.4 lists information about these interrupts. Table 11.4 Free-Running Timer Interrupts Interrupt Description Priority ICIA Requested by ICFA High ICIB Requested by ICFB ICIC Requested by ICFC ICID Requested by ICFD OCIA Requested by OCFA OCIB Requested by OCFB FOVI Requested by OVF Rev. 3.00 Mar 17, 2006 page 270 of 706 REJ09B0303-0300 Low Section 11 16-Bit Free-Running Timer 11.5 Sample Application In the example below, the free-running timer is used to generate pulse outputs with a 50% duty cycle and arbitrary phase relationship. The programming is as follows: • The CCLRA bit in TCSR is set to 1. • Each time a compare-match interrupt occurs, software inverts the corresponding output level bit in TOCR (OLVLA or OLVLB). FRC H'FFFF Counter clear OCRA OCRB H'0000 FTOA FTOB Figure 11.17 Pulse Output (Example) Rev. 3.00 Mar 17, 2006 page 271 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer 11.6 Usage Notes Application programmers should note that the following types of contention can occur in the freerunning timer. Contention between FRC Write and Clear: If an internal counter clear signal is generated during the state after an FRC write cycle, the clear signal takes priority and the write is not performed. Figure 11.18 shows this type of contention. FRC write cycle T1 T2 T3 φ Address FRC address Internal write signal Counter clear signal FRC N H'0000 Figure 11.18 FRC Write-Clear Contention Rev. 3.00 Mar 17, 2006 page 272 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Contention between FRC Write and Increment: Even if an increment pulse is generated in the T3 state during FRC write cycle, it is not incremented and the count write takes priority. Figure 11.19 shows this type of contention. FRC write cycle T1 T2 T3 φ Address FRC address Internal write signal FRC input clock FRC N M Write data Figure 11.19 FRC Write-Increment Contention Rev. 3.00 Mar 17, 2006 page 273 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Contention between OCR Write and Compare-Match: If a compare-match occurs in the T3 state during the OCRA or OCRB write cycle, the OCR write takes priority and the compare-match signal is inhibited. Figure 11.20 shows this type of contention. When the automatic addition of OCRAR/OCRAF to OCRA is selected and a compare-match occurs in the T3 state during the OCRA, OCRAR or OCRAF write cycle, the OCRA, OCRAR or OCRAF write takes priority and the compare-match signal is inhibited. Consequently, the result of automatic addition is not written. OCRA or OCRB write cycle T1 T2 T3 φ Address OCR address Internal write signal FRC N OCR N N+1 M Write data Compare-match signal Inhibited Figure 11.20 Contention between OCR Write and Compare-Match (When Not Using the Function of Automatic Addition) Rev. 3.00 Mar 17, 2006 page 274 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer φ Address OCRAR(OCRAF) address Internal write signal OCRAR (OCRAF) Old data Compare-match signal inhibited FRC N OCRA N New data N+1 Since the compare-match signal is inhibited, automatic addition does not occur. Figure 11.21 Contention between OCRAR/OCRAF Write and Compare-Match (When Using Automatic Addition) Switching of Internal Clock and FRC Operation: When the internal clock is changed, the changeover may cause FRC to increment. This depends on the time at which the clock select bits (CKS1 and CKS0) are rewritten, as shown in table 11.5. When an internal clock is used, the FRC clock is generated on detection of the falling edge of the internal clock scaled from the system clock (φ). If the clock is changed when the old source is high and the new source is low, as in case no. 3 in table 11.5, the changeover is regarded as a falling edge that triggers the FRC increment clock pulse. Switching between an internal and external clock can also cause FRC to increment. Rev. 3.00 Mar 17, 2006 page 275 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Table 11.5 Switching of Internal Clock and FRC Operation No. 1 Timing of Switchover by Means of CKS1 and CKS0 Bits Switching from low to low FRC Operation Clock before switchover Clock after switchover FRC clock FRC N+1 N CKS bit rewrite 2 Switching from low to high Clock before switchover Clock after switchover FRC clock FRC N N+1 N+2 CKS bit rewrite Rev. 3.00 Mar 17, 2006 page 276 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer No. 3 Timing of Switchover by Means of CKS1 and CKS0 Bits Switching from high to low FRC Operation Clock before switchover Clock after switchover * FRC clock FRC N N+1 N+2 CKS bit rewrite 4 Switching from high to high Clock before switchover Clock after switchover FRC clock FRC N N+1 N+2 CKS bit rewrite Note: * Generated on the assumption that the switchover is a falling edge; FRC is incremented. Rev. 3.00 Mar 17, 2006 page 277 of 706 REJ09B0303-0300 Section 11 16-Bit Free-Running Timer Rev. 3.00 Mar 17, 2006 page 278 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Section 12 8-Bit Timers 12.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip 8-bit timer module with two channels (TMR0 and TMR1). Each channel has an 8-bit counter (TCNT) and two time constant registers (TCORA and TCORB) that are constantly compared with the TCNT value to detect comparematches. The 8-bit timer module can be used as a multifunction timer in a variety of applications, such as generation of a rectangular-wave output with an arbitrary duty cycle. The H8/3577 Group and H8/3567 Group also have two similar 8-bit timer channels (TMRX and TMRY) that can be used in a connected configuration using the timer connection function. TMRX and TMRY have greater input/output and interrupt function related restrictions than TMR0 and TMR1. 12.1.1 Features • Selection of clock sources TMR0, TMR1: The counter input clock can be selected from six internal clocks and an external clock (enabling use as an external event counter). TMRX, TMRY: The counter input clock can be selected from three internal clocks and an external clock (enabling use as an external event counter). • Selection of three ways to clear the counters The counters can be cleared on compare-match A or B, or by an external reset signal. • Timer output controlled by two compare-match signals The timer output signal in each channel is controlled by two independent compare-match signals, enabling the timer to be used for various applications, such as the generation of pulse output or PWM output with an arbitrary duty cycle. (Note: TMRY does not have a timer output pin.) • Cascading of the two channels (TMR0, TMR1) Operation as a 16-bit timer can be performed using channel 0 as the upper half and channel 1 as the lower half (16-bit count mode). Channel 1 can be used to count channel 0 compare-match occurrences (compare-match count mode). • Multiple interrupt sources for each channel TMR0, TMR1, TMRY: Two compare-match interrupts and one overflow interrupt can be requested independently. TMRX: One input capture source is available. Rev. 3.00 Mar 17, 2006 page 279 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.1.2 Block Diagram Figure 12.1 shows a block diagram of the 8-bit timer module (TMR0 and TMR1). TMRX and TMRY have a similar configuration, but cannot be cascaded. TMRX also has an input capture function. For details, see section 13, Timer Connection. External clock sources Internal clock sources TMCI0 TMCI1 TMR0 φ/8, φ/2 φ/64, φ/32 φ/1024, φ/256 TMR1 φ/8, φ/2 φ/64, φ/128 φ/1024, φ/2048 TMRX φ φ/2 φ/4 TMRY φ/4 φ/256 φ/2048 Clock 1 Clock 0 Clock select TCORA0 Compare-match A1 Compare-match A0 Comparator A0 TCNT0 Comparator A1 TCNT1 Clear 0 Clear 1 Compare-match B1 Compare-match B0 Comparator B0 TMO1 TMRI1 Comparator B1 Control logic TCORB0 TCORB1 TCSR0 TCSR1 TCR0 TCR1 CMIA0 CMIB0 OVI0 CMIA1 CMIB1 OVI1 Interrupt signals Figure 12.1 Block Diagram of 8-Bit Timer Module Rev. 3.00 Mar 17, 2006 page 280 of 706 REJ09B0303-0300 Internal bus Overflow 1 Overflow 0 TMO0 TMRI0 TCORA1 Section 12 8-Bit Timers 12.1.3 Pin Configuration Table 12.1 summarizes the input and output pins of the 8-bit timer module. Table 12.1 8-Bit Timer Input and Output Pins Channel Name Symbol* I/O Function 0 Timer output TMO0 Output Output controlled by compare-match Timer clock input TMCI0 Input External clock input for the counter Timer reset input TMRI0 Input External reset input for the counter Timer output TMO1 Output Output controlled by compare-match Timer clock input TMCI1 Input External clock input for the counter Timer reset input TMRI1 Input External reset input for the counter Timer output TMOX Output Output controlled by compare-match Timer clock/ reset input HFBACKI/TMIX Input (TMCIX/TMRIX) External clock/reset input for the counter Timer clock/reset input VSYNCI/TMIY Input (TMCIY/TMRIY) External clock/reset input for the counter 1 X Y Note: * The abbreviations TMO, TMCI, and TMRI are used in the text, omitting the channel number. Channel X and Y I/O pins have the same internal configuration as channels 0 and 1, and therefore the same abbreviations are used. Rev. 3.00 Mar 17, 2006 page 281 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.1.4 Register Configuration Table 12.2 summarizes the registers of the 8-bit timer module. Table 12.2 8-Bit Timer Registers Channel Name Abbreviation* 0 Timer control register 0 Timer control/status register 0 Time constant register A0 Time constant register B0 Time counter 0 Timer control register 1 Timer control/status register 1 Time constant register A1 Time constant register B1 Timer counter 1 Serial timer control register Module stop control register TCR0 TCSR0 TCORA0 TCORB0 TCNT0 TCR1 TCSR1 TCORA1 TCORB1 TCNT1 STCR MSTPCRH MSTPCRL TCONRS TCRX TCSRX TCORAX TCORBX TCNTX TCORC TICRR TICRF TCRY TCSRY TCORAY TCORBY TCNTY TISR 1 Common X Y Timer connection register S Timer control register X Timer control/status register X Time constant register AX Time constant register BX Timer counter X Time constant register C Input capture register R Input capture register F Timer control register Y Timer control/status register Y Time constant register AY Time constant register BY Timer counter Y Timer input select register 2 R/W Initial value Address R/W 1 R/(W)* R/W R/W R/W R/W 1 R/(W)* H'00 H'00 H'FF H'FF H'00 H'00 H'10 H'FF H'FF H'00 H'00 H'3F H'FF H'00 H'00 H'00 H'FF H'FF H'00 H'FF H'00 H'00 H'00 H'00 H'FF H'FF H'00 H'FE H'FFC8 H'FFCA H'FFCC H'FFCE H'FFD0 H'FFC9 H'FFCB H'FFCD H'FFCF H'FFD1 H'FFC3 H'FF86 H'FF87 H'FFFE H'FFF0 H'FFF1 H'FFF6 H'FFF7 H'FFF4 H'FFF5 H'FFF2 H'FFF3 H'FFF0 H'FFF1 H'FFF2 H'FFF3 H'FFF4 H'FFF5 R/W R/W R/W R/W R/W R/W R/W R/W 1 R/(W)* R/W R/W R/W R/W R R R/W 1 R/(W)* R/W R/W R/W R/W Notes: 1. Only 0 can be written in bits 7 to 5, to clear these flags. 2. The abbreviations TCR, TCSR, TCORA, TCORB, and TCNT are used in the text, omitting the channel designation (0, 1, X, or Y). Rev. 3.00 Mar 17, 2006 page 282 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Each pair of registers for channel 0 and channel 1 comprises a 16-bit register with the upper 8 bits for channel 0 and the lower 8 bits for channel 1, so they can be accessed together by word access. (Access is not divided into two 8-bit accesses.) Certain of the channel X and channel Y registers are assigned to the same address. The TMRX/Y bit in TCONRS determines which register is accessed. 12.2 Register Descriptions 12.2.1 Timer Counter (TCNT) TCNT0 TCNT1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W TCNTX, TCNTY Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Each TCNT is an 8-bit readable/writable up-counter. TCNT0 and TCNT1 comprise a single 16-bit register, so they can be accessed together by word access. TCNT increments on pulses generated from an internal or external clock source. This clock source is selected by clock select bits CKS2 to CKS0 in TCR. TCNT can be cleared by an external reset input signal or compare-match signal. Counter clear bits CCLR1 and CCLR0 in TCR select the method of clearing. When TCNT overflows from H'FF to H'00, the overflow flag (OVF) in TCSR is set to 1. The timer counters are initialized to H'00 by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 283 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.2 Time Constant Register A (TCORA) TCORA0 TCORA1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W TCORAX, TCORAY Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCORA is an 8-bit readable/writable register. TCORA0 and TCORA1 comprise a single 16-bit register, so they can be accessed together by word access. TCORA is continually compared with the value in TCNT. When a match is detected, the corresponding compare-match flag A (CMFA) in TCSR is set. Note, however, that comparison is disabled during the T2 state of a TCORA write cycle. The timer output can be freely controlled by these compare-match signals and the settings of output select bits OS1 and OS0 in TCSR. TCORA is initialized to H'FF by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 284 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.3 Time Constant Register B (TCORB) TCORB0 TCORB1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W TCORBX, TCORBY Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCORB is an 8-bit readable/writable register. TCORB0 and TCORB1 comprise a single 16-bit register, so they can be accessed together by word access. TCORB is continually compared with the value in TCNT. When a match is detected, the corresponding compare-match flag B (CMFB) in TCSR is set. Note, however, that comparison is disabled during the T2 state of a TCORB write cycle. The timer output can be freely controlled by these compare-match signals and the settings of output select bits OS3 and OS2 in TCSR. TCORB is initialized to H'FF by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 285 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.4 Timer Control Register (TCR) Bit 7 6 5 4 3 2 1 0 CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCR is an 8-bit readable/writable register that selects the clock source and the time at which TCNT is cleared, and enables interrupts. TCR is initialized to H'00 by a reset and in hardware standby mode. For details of the timing, see section 12.3, Operation. Bit 7—Compare-Match Interrupt Enable B (CMIEB): Selects whether the CMFB interrupt request (CMIB) is enabled or disabled when the CMFB flag in TCSR is set to 1. Note that a CMIB interrupt is not requested by TMRX, regardless of the CMIEB value. Bit 7 CMIEB Description 0 CMFB interrupt request (CMIB) is disabled 1 CMFB interrupt request (CMIB) is enabled (Initial value) Bit 6—Compare-Match Interrupt Enable A (CMIEA): Selects whether the CMFA interrupt request (CMIA) is enabled or disabled when the CMFA flag in TCSR is set to 1. Note that a CMIA interrupt is not requested by TMRX, regardless of the CMIEA value. Bit 6 CMIEA Description 0 CMFA interrupt request (CMIA) is disabled 1 CMFA interrupt request (CMIA) is enabled Rev. 3.00 Mar 17, 2006 page 286 of 706 REJ09B0303-0300 (Initial value) Section 12 8-Bit Timers Bit 5—Timer Overflow Interrupt Enable (OVIE): Selects whether the OVF interrupt request (OVI) is enabled or disabled when the OVF flag in TCSR is set to 1. Note that an OVI interrupt is not requested by TMRX, regardless of the OVIE value. Bit 5 OVIE Description 0 OVF interrupt request (OVI) is disabled 1 OVF interrupt request (OVI) is enabled (Initial value) Bits 4 and 3—Counter Clear 1 and 0 (CCLR1, CCLR0): These bits select the method by which the timer counter is cleared: by compare-match A or B, or by an external reset input. Bit 4 Bit 3 CCLR1 CCLR0 Description 0 0 Clearing is disabled 1 Cleared on compare-match A 0 Cleared on compare-match B 1 Cleared on rising edge of external reset input 1 (Initial value) Bits 2 to 0—Clock Select 2 to 0 (CKS2 to CKS0): These bits select whether the clock input to TCNT is an internal or external clock. The input clock can be selected from either six or three clocks, all divided from the system clock (φ). The falling edge of the selected internal clock triggers the count. When use of an external clock is selected, three types of count can be selected: at the rising edge, the falling edge, and both rising and falling edges. Some functions differ between channel 0 and channel 1, because of the cascading function. Rev. 3.00 Mar 17, 2006 page 287 of 706 REJ09B0303-0300 Section 12 8-Bit Timers TCR STCR Bit 2 Bit 1 Bit 0 Bit 1 Bit 0 Channel CKS2 CKS1 CKS0 ICKS1 ICKS0 Description 0 1 Note: * 0 0 0 — — Clock input disabled (Initial value) 0 0 1 — 0 φ/8 internal clock source, counted on the falling edge 0 0 1 — 1 φ/2 internal clock source, counted on the falling edge 0 1 0 — 0 φ/64 internal clock source, counted on the falling edge 0 1 0 — 1 φ/32 internal clock source, counted on the falling edge 0 1 1 — 0 φ/1024 internal clock source, counted on the falling edge 0 1 1 — 1 1 0 0 — — φ/256 internal clock source, counted on the falling edge Counted on TCNT1 overflow signal* 0 0 0 — — Clock input disabled 0 0 1 0 — φ/8 internal clock source, counted on the falling edge 0 0 1 1 — φ/2 internal clock source, counted on the falling edge 0 1 0 0 — φ/64 internal clock source, counted on the falling edge 0 1 0 1 — φ/128 internal clock source, counted on the falling edge 0 1 1 0 — φ/1024 internal clock source, counted on the falling edge 0 1 1 1 — 1 0 0 — — φ/2048 internal clock source, counted on the falling edge Counted on TCNT0 compare-match A* (Initial value) If the count input of channel 0 is the TCNT1 overflow signal and that of channel 1 is the TCNT0 compare-match signal, no incrementing clock will be generated. Do not use this setting. Rev. 3.00 Mar 17, 2006 page 288 of 706 REJ09B0303-0300 Section 12 8-Bit Timers TCR STCR Bit 2 Bit 1 Bit 0 Bit 1 Bit 0 Channel CKS2 CKS1 CKS0 ICKS1 ICKS0 Description X Y 0 0 0 — — Clock input disabled (Initial value) 0 0 1 — — Counted on φ internal clock source 0 1 0 — — φ/2 internal clock source, counted on the falling edge 0 1 1 — — φ/4 internal clock source, counted on the falling edge 1 0 0 — — Clock input disabled 0 0 0 — — Clock input disabled 0 0 1 — — φ/4 internal clock source, counted on the falling edge 0 1 0 — — φ/256 internal clock source, counted on the falling edge 0 1 1 — — φ/2048 internal clock source, counted on the falling edge (Initial value) 1 0 0 — — Clock input disabled Common 1 0 1 — — External clock source, counted at rising edge 1 1 0 — — External clock source, counted at falling edge 1 1 1 — — External clock source, counted at both rising and falling edges Rev. 3.00 Mar 17, 2006 page 289 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.5 Timer Control/Status Register (TCSR) TCSR0 Bit Initial value Read/Write 7 6 5 4 3 2 1 0 CMFB CMFA OVF ADTE OS3 OS2 OS1 OS0 0 R/(W)* 0 0 0 0 0 0 0 R/(W)* R/(W)* R/W R/W R/W R/W R/W TCSR1 Bit 7 6 5 4 3 2 1 0 CMFB CMFA OVF — OS3 OS2 OS1 OS0 Initial value 0 0 0 1 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* — R/W R/W R/W R/W 7 6 5 4 3 2 1 0 CMFB CMFA OVF ICF OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/W R/W R/W R/W 7 6 5 4 3 2 1 0 CMFB CMFA OVF ICIE OS3 OS2 OS1 OS0 0 R/(W)* 0 0 0 0 0 0 0 R/(W)* R/(W)* R/W R/W R/W R/W R/W TCSRX Bit TCSRY Bit Initial value Read/Write Note: * Only 0 can be written in bits 7 to 5, and in bit 4 in TCSRX, to clear these flags. TCSR is an 8-bit register that indicates compare-match and overflow statuses (and input capture status in TMRX only), and controls compare-match output. TCSR0, TCSRX, and TCSRY are initialized to H'00, and TCSR1 is initialized to H'10, by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 290 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Bit 7—Compare-Match Flag B (CMFB): Status flag indicating whether the values of TCNT and TCORB match. Bit 7 CMFB Description 0 [Clearing condition] (Initial value) Read CMFB when CMFB = 1, then write 0 in CMFB 1 [Setting condition] When TCNT = TCORB Bit 6—Compare-match Flag A (CMFA): Status flag indicating whether the values of TCNT and TCORA match. Bit 6 CMFA Description 0 [Clearing condition] (Initial value) Read CMFA when CMFA = 1, then write 0 in CMFA 1 [Setting condition] When TCNT = TCORA Bit 5 —Timer Overflow Flag (OVF): Status flag indicating that TCNT has overflowed (changed from H'FF to H'00). Bit 5 OVF Description 0 [Clearing condition] (Initial value) Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] When TCNT overflows from H'FF to H'00 Rev. 3.00 Mar 17, 2006 page 291 of 706 REJ09B0303-0300 Section 12 8-Bit Timers TCSR0 Bit 4—A/D Trigger Enable (ADTE): Enables or disables A/D converter start requests by compare-match A. TCSR0 Bit 4 ADTE Description 0 A/D converter start requests by compare-match A are disabled 1 A/D converter start requests by compare-match A are enabled (Initial value) TCSR1 Bit 4—Reserved: This bit cannot be modified and is always read as 1. TCSRX Bit 4—Input Capture Flag (ICF): Status flag that indicates detection of a rising edge followed by a falling edge in the external reset signal after the ICST bit in TCONRI has been set to 1. TCSRX Bit 4 ICF Description 0 [Clearing condition] (Initial value) Read ICF when ICF = 1, then write 0 in ICF 1 [Setting condition] When a rising edge followed by a falling edge is detected in the external reset signal after the ICST bit in TCONRI has been set to 1 TCSRY Bit 4—Input Capture Interrupt Enable (ICIE): Selects enabling or disabling of the interrupt request by ICF (ICIX) when the ICF bit in TCSRX is set to 1. TCSRY Bit 4 ICIE Description 0 Interrupt request by ICF (ICIX) is disabled 1 Interrupt request by ICF (ICIX) is enabled Rev. 3.00 Mar 17, 2006 page 292 of 706 REJ09B0303-0300 (Initial value) Section 12 8-Bit Timers Bits 3 to 0—Output Select 3 to 0 (OS3 to OS0): These bits specify how the timer output level is to be changed by a compare-match of TCOR and TCNT. OS3 and OS2 select the effect of compare-match B on the output level, OS1 and OS0 select the effect of compare-match A on the output level, and both of them can be controlled independently. Note, however, that priorities are set such that: trigger output > 1 output > 0 output. If comparematches occur simultaneously, the output changes according to the compare-match with the higher priority. Timer output is disabled when bits OS3 to OS0 are all 0. After a reset, the timer output is 0 until the first compare-match occurs. Bit 3 Bit 2 OS3 OS2 Description 0 0 No change when compare-match B occurs 1 0 is output when compare-match B occurs 0 1 is output when compare-match B occurs 1 Output is inverted when compare-match B occurs (toggle output) 1 (Initial value) Bit 1 Bit 0 OS1 OS0 Description 0 0 No change when compare-match A occurs 1 0 is output when compare-match A occurs 0 1 is output when compare-match A occurs 1 Output is inverted when compare-match A occurs (toggle output) 1 (Initial value) Rev. 3.00 Mar 17, 2006 page 293 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.6 Serial Timer Control Register (STCR) Bit 7 6 5 4 3 2 1 0 — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W STCR is an 8-bit readable/writable register that controls register access, the IIC operating mode (when the on-chip IIC option is included), and on-chip flash memory (in F-ZTAT versions), and also selects the TCNT input clock. For details on functions not related to the 8-bit timers, see section 3.2.3, Serial Timer Control Register (STCR), and the descriptions of the relevant modules. If a module controlled by STCR is not used, do not write 1 to the corresponding bit. STCR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—Reserved: Do not write 1 to this bit. 2 2 Bits 6 to 4—I C Control (IICX1, IICX0, IICE): These bits control the operation of the I C bus 2 interface when the IIC option is included on-chip. See section 16, I C Bus Interface, for details. Bit 3—Reserved: This bit must not be set to 1. Bit 2—USB Enable (USBE): This bit controls CPU access to the USB data register and control register. Bit 2 USBE Description 0 Prohibition of the above register access 1 Permission of the above register access (initial value) Bits 1 and 0—Internal Clock Select 1 and 0 (ICKS1, ICKS0): These bits, together with bits CKS2 to CKS0 in TCR, select the clock to be input to TCNT. For details, see section 12.2.4, Timer Control Register. Rev. 3.00 Mar 17, 2006 page 294 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.7 System Control Register (SYSCR) Bit 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W Only bit 1 is described here. For details on functions not related to the 8-bit timers, see sections 3.2.2 and 5.2.1, System Control Register (SYSCR), and the descriptions of the relevant modules. Bit 1—Host Interface Enable (HIE): Controls CPU access to 8-bit timer (channel X and Y) data registers and control registers, and timer connection control registers. Bit 1 HIE Description 0 CPU access to 8-bit timer (channel X and Y) data registers and control registers, and timer connection control registers, is enabled (Initial value) 1 CPU access to 8-bit timer (channel X and Y) data registers and control registers, and timer connection control registers, is disabled 12.2.8 Timer Connection Register S (TCONRS) Bit 7 6 5 4 3 2 HOMOD1 HOMOD0 VOMOD1 VOMOD0 1 0 TMRX/Y ISGENE CLMOD1 CLMOD0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCONRS is an 8-bit readable/writable register that controls access to the TMRX and TMRY registers and timer connection operation. TCONRS is initialized to H'00 by a reset and in hardware standby mode. Bit 7—TMRX/TMRY Access Select (TMRX/Y): The TMRX and TMRY registers can only be accessed when the HIE bit in SYSCR is cleared to 0. In the H8/3577 Group and H8/3567 Group, some of the TMRX registers and the TMRY registers are assigned to the same memory space addresses (H'FFF0 to H'FFF5), and the TMRX/Y bit determines which registers are accessed. Rev. 3.00 Mar 17, 2006 page 295 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Accessible Registers Bit 7 TMRX/Y H'FFF0 H'FFF1 H'FFF2 H'FFF3 H'FFF4 0 TCRX (Initial value) (TMRX) TCSRX (TMRX) TICRR (TMRX) TICRF (TMRX) TCNTX TCORC TCORAX TCORBX (TMRX) (TMRX) (TMRX) (TMRX) 1 TCSRY (TMRY) TCORAY TCORBY TCNTY TISR (TMRY) (TMRY) (TMRY) (TMRY) 12.2.9 TCRY (TMRY) H'FFF5 H'FFF6 H'FFF7 Input Capture Register (TICR) [TMRX Additional Function] Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write — — — — — — — — TICR is an 8-bit internal register to which the contents of TCNT are transferred on the falling edge of external reset input. The CPU cannot read or write to TICR directly. The TICR function is used in timer connection. For details, see section 13, Timer Connection. 12.2.10 Time Constant Register C (TCORC) [TMRX Additional Function] Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCORC is an 8-bit readable/writable register. The sum of the contents of TCORC and TICR is continually compared with the value in TCNT. When a match is detected, a compare-match C signal is generated. Note, however, that comparison is disabled during the T2 state of a TCORC write cycle and a TICR input capture cycle. TCORC is initialized to H'FF by a reset and in hardware standby mode. The TCORC function is used in timer connection. For details, see section 13, Timer Connection. Rev. 3.00 Mar 17, 2006 page 296 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.11 Input Capture Registers R and F (TICRR, TICRF) [TMRX Additional Functions] Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R TICRR and TICRF are 8-bit read-only registers. When the ICST bit in TCONRI is set to 1, TICRR and TICRF capture the contents of TCNT successively on the rise and fall of the external reset input. When one capture operation ends, the ICST bit is cleared to 0. TICRR and TICRF are each initialized to H'00 by a reset and in hardware standby mode. The TICRR and TICRF functions are used in timer connection. For details, see section 13, Timer Connection. 12.2.12 Timer Input Select Register (TISR) [TMRY Additional Function] Bit 7 6 5 4 3 2 1 0 — — — — — — — IS Initial value 1 1 1 1 1 1 1 0 Read/Write — — — — — — — R/W TISR is an 8-bit readable/writable register that selects the external clock/reset signal source for the counter. TISR is initialized to H'FE by a reset and in hardware standby mode. Bits 7 to 1—Reserved: Do not write 0. Bit 0—Input Select (IS): Selects the internal synchronization signal (IVG signal) or the timer clock/reset input pin (TMIY (TMCIY/TMRIY)) as the external clock/reset signal source for the counter. Bit 0 IS Description 0 IVG signal is selected 1 TMIY (TMCIY/TMRIY) is selected (Initial value) Rev. 3.00 Mar 17, 2006 page 297 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.2.13 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers, and is used to perform module stop mode control. When the MSTP12 bit or MSTP8 bit is set to 1, at the end of the bus cycle 8-bit timer operation is halted on channels 0 and 1 or channels X and Y, respectively, and a transition is made to module stop mode. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 4—Module Stop (MSTP12): Specifies 8-bit timer (channel 0/1) module stop mode. MSTPCRH Bit 4 MSTP12 Description 0 8-bit timer (channel 0/1) module stop mode is cleared 1 8-bit timer (channel 0/1) module stop mode is set (Initial value) MSTPCRH Bit 0—Module Stop (MSTP8): Specifies 8-bit timer (channel X/Y) and timer connection module stop mode. MSTPCRH Bit 0 MSTP8 Description 0 8-bit timer (channel X/Y) and timer connection module stop mode is cleared 1 8-bit timer (channel X/Y) and timer connection module stop mode is set (Initial value) Rev. 3.00 Mar 17, 2006 page 298 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.3 Operation 12.3.1 TCNT Incrementation Timing TCNT is incremented by input clock pulses (either internal or external). Internal Clock: An internal clock created by dividing the system clock (φ) can be selected by setting bits CKS2 to CKS0 in TCR. Figure 12.2 shows the count timing. φ Internal clock TCNT input clock TCNT N–1 N N+1 Figure 12.2 Count Timing for Internal Clock Input External Clock: Three incrementation methods can be selected by setting bits CKS2 to CKS0 in TCR: at the rising edge, the falling edge, and both rising and falling edges. Note that the external clock pulse width must be at least 1.5 states for incrementation at a single edge, and at least 2.5 states for incrementation at both edges. The counter will not increment correctly if the pulse width is less than these values. Figure 12.3 shows the timing of incrementation at both edges of an external clock signal. Rev. 3.00 Mar 17, 2006 page 299 of 706 REJ09B0303-0300 Section 12 8-Bit Timers φ External clock input pin TCNT input clock TCNT N–1 N N+1 Figure 12.3 Count Timing for External Clock Input 12.3.2 Compare-Match Timing Setting of Compare-Match Flags A and B (CMFA, CMFB): The CMFA and CMFB flags in TCSR are set to 1 by a compare-match signal generated when the TCOR and TCNT values match. The compare-match signal is generated at the last state in which the match is true, just before the timer counter is updated. Therefore, when TCOR and TCNT match, the compare-match signal is not generated until the next incrementation clock input. Figure 12.4 shows this timing. φ TCNT N TCOR N Compare-match signal CMF Figure 12.4 Timing of CMF Setting Rev. 3.00 Mar 17, 2006 page 300 of 706 REJ09B0303-0300 N+1 Section 12 8-Bit Timers Timer Output Timing: When compare-match A or B occurs, the timer output changes as specified by the output select bits (OS3 to OS0) in TCSR. Depending on these bits, the output can remain the same, be set to 0, be set to 1, or toggle. Figure 12.5 shows the timing when the output is set to toggle at compare-match A. φ Compare-match A signal Timer output pin Figure 12.5 Timing of Timer Output Timing of Compare-Match Clear: TCNT is cleared when compare-match A or B occurs, depending on the setting of the CCLR1 and CCLR0 bits in TCR. Figure 12.6 shows the timing of this operation. φ Compare-match signal TCNT N H'00 Figure 12.6 Timing of Compare-Match Clear Rev. 3.00 Mar 17, 2006 page 301 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.3.3 TCNT External Reset Timing TCNT is cleared at the rising edge of an external reset input, depending on the settings of the CCLR1 and CCLR0 bits in TCR. The width of the clearing pulse must be at least 1.5 states. Figure 12.7 shows the timing of this operation. φ External reset input pin Clear signal TCNT N–1 N H'00 Figure 12.7 Timing of Clearing by External Reset Input 12.3.4 Timing of Overflow Flag (OVF) Setting OVF in TCSR is set to 1 when the timer count overflows (changes from H'FF to H'00). Figure 12.8 shows the timing of this operation. φ TCNT H'FF H'00 Overflow signal OVF Figure 12.8 Timing of OVF Setting Rev. 3.00 Mar 17, 2006 page 302 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.3.5 Operation with Cascaded Connection If bits CKS2 to CKS0 in either TCR0 or TCR1 are set to B'100, the 8-bit timers of the two channels are cascaded. With this configuration, a single 16-bit timer can be used (16-bit timer mode) or compare-matches of 8-bit channel 0 can be counted by the timer of channel 1 (comparematch count mode). In this case, the timer operates as described below. 16-Bit Count Mode: When bits CKS2 to CKS0 in TCR0 are set to B'100, the timer functions as a single 16-bit timer with channel 0 occupying the upper 8 bits and channel 1 occupying the lower 8 bits. • Setting of compare-match flags The CMF flag in TCSR0 is set to 1 when a 16-bit compare-match occurs. The CMF flag in TCSR1 is set to 1 when a lower 8-bit compare-match occurs. • Counter clear specification If the CCLR1 and CCLR0 bits in TCR0 have been set for counter clear at compare-match, the 16-bit counter (TCNT0 and TCNT1 together) is cleared when a 16-bit compare-match occurs. The 16-bit counter (TCNT0 and TCNT1 together) is cleared even if counter clear by the TMRI0 pin has also been set. The settings of the CCLR1 and CCLR0 bits in TCR1 are ignored. The lower 8 bits cannot be cleared independently. • Pin output Control of output from the TMO0 pin by bits OS3 to OS0 in TCSR0 is in accordance with the 16-bit compare-match conditions. Control of output from the TMO1 pin by bits OS3 to OS0 in TCSR1 is in accordance with the lower 8-bit compare-match conditions. Compare-Match Count Mode: When bits CKS2 to CKS0 in TCR1 are B'100, TCNT1 counts compare-match A’s for channel 0. Channels 0 and 1 are controlled independently. Conditions such as setting of the CMF flag, generation of interrupts, output from the TMO pin, and counter clearing are in accordance with the settings for each channel. Usage Note: If the 16-bit count mode and compare-match count mode are set simultaneously, the input clock pulses for TCNT0 and TCNT1 are not generated and thus the counters will stop operating. Simultaneous setting of these two modes should therefore be avoided. Rev. 3.00 Mar 17, 2006 page 303 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.4 Interrupt Sources The TMR0, TMR1, and TMRY 8-bit timers can generate three types of interrupt: compare-match A and B (CMIA and CMIB), and overflow (OVI). TMRX can generate only an ICIX interrupt. An interrupt is requested when the corresponding interrupt enable bit is set in TCR or TCSR. Independent signals are sent to the interrupt controller for each interrupt. An overview of 8-bit timer interrupt sources is given in tables 12.3 to 12.5. Table 12.3 TMR0 and TMR1 8-Bit Timer Interrupt Sources Interrupt source Description Interrupt Priority CMIA Requested by CMFA High CMIB Requested by CMFB OVI Requested by OVF Low Table 12.4 TMRX 8-Bit Timer Interrupt Source Interrupt source Description ICIX Requested by ICF Table 12.5 TMRY 8-Bit Timer Interrupt Sources Interrupt source Description Interrupt Priority CMIA Requested by CMFA High CMIB Requested by CMFB OVI Requested by OVF Rev. 3.00 Mar 17, 2006 page 304 of 706 REJ09B0303-0300 Low Section 12 8-Bit Timers 12.5 8-Bit Timer Application Example In the example below, the 8-bit timer is used to generate a pulse output with a selected duty cycle, as shown in figure 12.9. The control bits are set as follows: • In TCR, CCLR1 is cleared to 0 and CCLR0 is set to 1 so that the timer counter is cleared by a TCORA compare-match. • In TCSR, bits OS3 to OS0 are set to B'0110, causing 1 output at a TCORA compare-match and 0 output at a TCORB compare-match. With these settings, the 8-bit timer provides output of pulses at a rate determined by TCORA with a pulse width determined by TCORB. No software intervention is required. TCNT H'FF Counter clear TCORA TCORB H'00 TMO Figure 12.9 Pulse Output (Example) Rev. 3.00 Mar 17, 2006 page 305 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.6 Usage Notes Application programmers should note that the following kinds of contention can occur in the 8-bit timer module. 12.6.1 Contention between TCNT Write and Clear If a timer counter clock pulse is generated during the T2 state of a TCNT write cycle, the clear takes priority, so that the counter is cleared and the write is not performed. Figure 12.10 shows this operation. TCNT write cycle by CPU T1 T2 T3 φ Address TCNT address Internal write signal Counter clear signal TCNT N H'00 Figure 12.10 Contention between TCNT Write and Clear Rev. 3.00 Mar 17, 2006 page 306 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.6.2 Contention between TCNT Write and Increment If a timer counter clock pulse is generated during the T2 state of a TCNT write cycle, the write takes priority and the counter is not incremented. Figure 12.11 shows this operation. TCNT write cycle by CPU T1 T2 T3 φ Address TCNT address Internal write signal TCNT input clock TCNT N M Counter write data Figure 12.11 Contention between TCNT Write and Increment Rev. 3.00 Mar 17, 2006 page 307 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.6.3 Contention between TCOR Write and Compare-Match During the T2 state of a TCOR write cycle, the TCOR write has priority even if a compare-match occurs and the compare-match signal is disabled. Figure 12.12 shows this operation. With TMRX, an ICR input capture contends with a compare-match in the same way as with a write to TCORC. In this case, the input capture has priority and the compare-match signal is inhibited. TCOR write cycle by CPU T1 T2 T3 φ Address TCOR address Internal write signal TCNT N N+1 TCOR N M TCOR write data Compare-match signal Inhibited Figure 12.12 Contention between TCOR Write and Compare-Match Rev. 3.00 Mar 17, 2006 page 308 of 706 REJ09B0303-0300 Section 12 8-Bit Timers 12.6.4 Contention between Compare-Matches A and B If compare-matches A and B occur at the same time, the 8-bit timer operates in accordance with the priorities for the output states set for compare-match A and compare-match B, as shown in table 12.6. Table 12.6 Timer Output Priorities Output Setting Priority Toggle output High 1 output 0 output No change 12.6.5 Low Switching of Internal Clocks and TCNT Operation TCNT may increment erroneously when the internal clock is switched over. Table 12.7 shows the relationship between the timing at which the internal clock is switched (by writing to the CKS1 and CKS0 bits) and the TCNT operation When the TCNT clock is generated from an internal clock, the falling edge of the internal clock pulse is detected. If clock switching causes a change from high to low level, as shown in no. 3 in table 12.7, a TCNT clock pulse is generated on the assumption that the switchover is a falling edge. This increments TCNT. Erroneous incrementation can also happen when switching between internal and external clocks. Rev. 3.00 Mar 17, 2006 page 309 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Table 12.7 Switching of Internal Clock and TCNT Operation No. 1 Timing of Switchover by Means of CKS1 and CKS0 Bits TCNT Clock Operation Switching from low 1 to low* Clock before switchover Clock after switchover TCNT clock TCNT N N+1 CKS bit rewrite 2 Switching from low 2 to high* Clock before switchover Clock after switchover TCNT clock TCNT N N+1 N+2 CKS bit rewrite Rev. 3.00 Mar 17, 2006 page 310 of 706 REJ09B0303-0300 Section 12 8-Bit Timers No. 3 Timing of Switchover by Means of CKS1 and CKS0 Bits TCNT Clock Operation Switching from high 3 to low* Clock before switchover Clock after switchover *4 TCNT clock TCNT N N+1 N+2 CKS bit rewrite 4 Switching from high to high Clock before switchover Clock after switchover TCNT clock TCNT N N+1 N+2 CKS bit rewrite Notes: 1. 2. 3. 4. Includes switching from low to stop, and from stop to low. Includes switching from stop to high. Includes switching from high to stop. Generated on the assumption that the switchover is a falling edge; TCNT is incremented. Rev. 3.00 Mar 17, 2006 page 311 of 706 REJ09B0303-0300 Section 12 8-Bit Timers Rev. 3.00 Mar 17, 2006 page 312 of 706 REJ09B0303-0300 Section 13 Timer Connection Section 13 Timer Connection 13.1 Overview The H8/3577 Group and H8/3567 Group allow interconnection between a combination of input signals, the single free-running timer (FRT) channel, and the three 8-bit timer channels (TMR1, TMRX, and TMRY). This capability can be used to implement complex functions such as PWM decoding and clamp waveform output. All the timers are initially set for independent operation. 13.1.1 Features The features of the timer connection facility are as follows. • Five input pins and four output pins, all of which can be designated for phase inversion. Positive logic is assumed for all signals used within the timer connection facility. • An edge-detection circuit is connected to the input pins, simplifying signal input detection. • TMRX can be used for PWM input signal decoding. • TMRX can be used for clamp waveform generation. • An external clock signal divided by TMR1 can be used as the FRT capture input signal. • An internal synchronization signal can be generated using the FRT and TMRY. • A signal generated/modified using an input signal and timer connection can be selected and output. Rev. 3.00 Mar 17, 2006 page 313 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 314 of 706 REJ09B0303-0300 Figure 13.1 Block Diagram of Timer Connection Facility HFBACKI/ FTCI/TMIX/ TMCI0 CSYNCI/ TMRI1/FTOB HSYNCI/ TMCI1/FTID FTIC Phase inversion Phase inversion Phase inversion Phase inversion Phase inversion Edge detection Edge detection Edge detection Edge detection Edge detection IHI signal selection IVI signal selection FRT input selection IVI signal IHI signal Read flag Read flag 16-bit FRT Vertical sync signal modify FTOA ICR +1C compare-match ICR 8-bit TMRX PWM decoding PDC signal TMRI CMA TMO CMB CMB TMCI 8-bit TMR1 TMO Clamp waveform generation CM1C TMRI TMCI TMR1 input selection Blanking waveform generation SET RES 2f H mask generation 2f H mask/flag FTIB OCRA +VR, +VF CMA(R) FTIC ICRD +1M, +2M CMA(F) compare-match FTOB FTID CM1M CM2M FTIA SET sync RES CL2 signal CL3 signal CL1 signal RES Vertical sync signal generation SET CLO signal selection CL4 signal FRT output selection Phase inversion Phase inversion Phase inversion TMOX TMO1 output selection TMRI/TMCI 8-bit TMRY TMO IVO signal Phase inversion CL4 generation IHO signal selection TMIY signal selection IVG signal IVO signal selection CLAMP0/ FTIC/ TMO0 HSYNCO/ TMO1/ TMOX CBLANK IHG signal VSYNCO/ FTOA 13.1.2 VFBACKI/ FTIB/TMRI0 VSYNCI/ FTIA/TMIY Section 13 Timer Connection Block Diagram Figure 13.1 shows a block diagram of the timer connection facility. Section 13 Timer Connection 13.1.3 Input and Output Pins Table 13.1 lists the timer connection input and output pins. Table 13.1 Timer Connection Input and Output Pins Name Abbreviation Input/ Output Vertical synchronization signal input pin VSYNCI Input Vertical synchronization signal input pin or FTIA input pin/TMIY input pin Horizontal synchronization signal input pin HSYNCI Input Horizontal synchronization signal input pin or FTID input pin/TMCI1 input pin Composite synchronization signal input pin CSYNCI Input Composite synchronization signal input pin or TMRI1 input pin/FTOB output pin Spare vertical synchronization signal input pin VFBACKI Input Spare vertical synchronization signal input pin or FTIB input pin/TMRI0 input pin Spare horizontal synchronization signal input pin HFBACKI Input Spare horizontal synchronization signal input pin or FTCI input pin/TMCI0 input pin/TMIX input pin Vertical synchronization signal output pin VSYNCO Output Vertical synchronization signal output pin or FTOA output pin Horizontal synchronization signal output pin HSYNCO Output Horizontal synchronization signal output pin or TMO1 output pin/TMOX output pin Clamp waveform output pin CLAMPO Output Clamp waveform output pin or TMO0 output pin/FTIC input pin Blanking waveform output pin CBLANK Output Blanking waveform output pin Function Rev. 3.00 Mar 17, 2006 page 315 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.1.4 Register Configuration Table 13.2 lists the timer connection registers. Timer connection registers can only be accessed when the HIE bit in SYSCR is 0. Table 13.2 Register Configuration Name Abbreviation R/W Initial Value Address Timer connection register I TCONRI R/W H'00 H'FFFC Timer connection register O TCONRO R/W H'00 H'FFFD Timer connection register S TCONRS R/W H'00 H'FFFE Edge sense register SEDGR 1 R/(W)* 2 H'00* H'FFFF Module stop control register MSTPRH R/W H'3F H'FF86 MSTPRL R/W H'FF H'FF87 Notes: 1. Bits 7 to 2: Only 0 can be written to clear the flags. 2. Bits 1 and 0: Undefined (reflect the pin states). 13.2 Register Descriptions 13.2.1 Timer Connection Register I (TCONRI) Bit 7 6 SIMOD1 SIMOD0 5 4 3 2 1 0 SCONE ICST HFINV VFINV HIINV VIINV Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCONRI is an 8-bit readable/writable register that controls connection between timers, the signal source for synchronization signal input, phase inversion, etc. TCONR1 is initialized to H'00 by a reset and in hardware standby mode. Rev. 3.00 Mar 17, 2006 page 316 of 706 REJ09B0303-0300 Section 13 Timer Connection Bits 7 and 6—Input Synchronization Mode Select 1 and 0 (SIMOD1, SIMOD0): These bits select the signal source of the IHI and IVI signals. Bit 7 Bit 6 SIMOD1 SIMOD0 Mode 0 0 No signal 1 S-on-G mode 1 Description (Initial value) IHI Signal IVI Signal HFBACKI input VFBACKI input CSYNCI input PDC input 0 Composite mode HSYNCI input PDC input 1 Separate mode HSYNCI input VSYNCI input Bit 5—Synchronization Signal Connection Enable (SCONE): Selects the signal source of the FRT FTI input and the TMR1 TMCI1/TMRI1 input. Bit 5 Description SCONE Mode FTIA FTIB FTIC FTID TMCI1 TMRI1 0 Normal connection (Initial value) FTIA input FTIB input FTIC input FTID input TMCI1 input TMRI1 input 1 Synchronization signal connection mode TMO1 signal VFBACKI IHI input signal IHI signal IVI inverse signal IVI signal Bit 4—Input Capture Start Bit (ICST): The TMRX external reset input (TMRIX) is connected to the IHI signal. TMRX has input capture registers (TICR, TICRR, and TICRF). TICRR and TICRF can measure the width of a short pulse by means of a single capture operation under the control of the ICST bit. When a rising edge followed by a falling edge is detected on TMRIX after the ICST bit is set to 1, the contents of TCNT at those points are captured into TICRR and TICRF, respectively, and the ICST bit is cleared to 0. Bit 4 ICST Description 0 The TICRR and TICRF input capture functions are stopped (Initial value) [Clearing condition] When a rising edge followed by a falling edge is detected on TMRIX 1 The TICRR and TICRF input capture functions are operating (Waiting for detection of a rising edge followed by a falling edge on TMRIX) [Setting condition] When 1 is written in ICST after reading ICST = 0 Rev. 3.00 Mar 17, 2006 page 317 of 706 REJ09B0303-0300 Section 13 Timer Connection Bits 3 to 0—Input Synchronization Signal Inversion (HFINV, VFINV, HIINV, VIINV): These bits select inversion of the input phase of the spare horizontal synchronization signal (HFBACKI), the spare vertical synchronization signal (VFBACKI), the horizontal synchronization signal and composite synchronization signal (HSYNCI, CSYNCI), and the vertical synchronization signal (VSYNCI). Bit 3 HFINV Description 0 The HFBACKI pin state is used directly as the HFBACKI input 1 The HFBACKI pin state is inverted before use as the HFBACKI input (Initial value) Bit 2 VFINV Description 0 The VFBACKI pin state is used directly as the VFBACKI input 1 The VFBACKI pin state is inverted before use as the VFBACKI input (Initial value) Bit 1 HIINV Description 0 The HSYNCI and CSYNCI pin states are used directly as the HSYNCI and CSYNCI inputs (Initial value) 1 The HSYNCI and CSYNCI pin states are inverted before use as the HSYNCI and CSYNCI inputs Bit 0 VIINV Description 0 The VSYNCI pin state is used directly as the VSYNCI input 1 The VSYNCI pin state is inverted before use as the VSYNCI input 13.2.2 (Initial value) Timer Connection Register O (TCONRO) Bit 7 6 5 4 3 2 HOE VOE CLOE CBOE HOINV VOINV Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 318 of 706 REJ09B0303-0300 1 0 CLOINV CBOINV Section 13 Timer Connection TCONRO is an 8-bit readable/writable register that controls output signal output, phase inversion, etc. TCONRO is initialized to H'00 by a reset and in hardware standby mode. Bits 7 to 4—Output Enable (HOE, VOE, CLOE, CBOE): These bits control enabling/disabling of horizontal synchronization signal (HSYNCO), vertical synchronization signal (VSYNCO), clamp waveform (CLAMPO), and blanking waveform (CBLANK) output. When output is disabled, the state of the relevant pin is determined by the port DR and DDR, FRT, TMR, and PWM settings. Output enabling/disabling control does not affect the port, FRT, or TMR input functions, but some FRT and TMR input signal sources are determined by the SCONE bit in TCONRI. Bit 7 HOE Description 0 The P67/TMO1/TMOX/HSYNCO pin functions as the P67/TMO1/TMOX pin (Initial value) 1 The P67/TMO1/TMOX/HSYNCO pin functions as the HSYNCO pin Bit 6 VOE Description 0 The P61/FTOA/VSYNCO pin functions as the P61/FTOA pin 1 The P61/FTOA/VSYNCO pin functions as the VSYNCO pin (Initial value) Bit 5 CLOE Description 0 The P64/FTIC/TMO0/CLAMPO pin functions as the P64/FTIC/TMO0 pin 1 The P64/FTIC/TMO0/CLAMPO pin functions as the CLAMPO pin (Initial value) Bit 4 CBOE Description 0 [H8/3577 Group] P27/PW15/CBLANK pin functions as the P27/PW15 pin [H8/3567 Group] P15/PW5/CBLANK pin functions as the P15/PW5 pin 1 (Initial value) [H8/3577 Group] P27/PW15/CBLANK pin functions as the CBLANK pin [H8/3567 Group] P15/PW5/CBLANK pin functions as the CBLANK pin Rev. 3.00 Mar 17, 2006 page 319 of 706 REJ09B0303-0300 Section 13 Timer Connection Bits 3 to 0—Output Synchronization Signal Inversion (HOINV, VOINV, CLOINV, CBOINV): These bits select inversion of the output phase of the horizontal synchronization signal (HSYNCO), the vertical synchronization signal (VSYNCO), the clamp waveform (CLAMPO), and the blank waveform (CBLANK). Bit 3 HOINV Description 0 The IHO signal is used directly as the HSYNCO output 1 The IHO signal is inverted before use as the HSYNCO output (Initial value) Bit 2 VOINV Description 0 The IVO signal is used directly as the VSYNCO output 1 The IVO signal is inverted before use as the VSYNCO output (Initial value) Bit 1 CLOINV Description 0 The CLO signal (CL1, CL2, CL3, or CL4 signal) is used directly as the CLAMPO output 1 The CLO signal (CL1, CL2, CL3, or CL4 signal) is inverted before use as the CLAMPO output (Initial value) Bit 0 CBOINV Description 0 The CBLANK signal is used directly as the CBLANK output 1 The CBLANK signal is inverted before use as the CBLANK output 13.2.3 (Initial value) Timer Connection Register S (TCONRS) Bit 7 6 5 4 3 2 1 0 TMRX/Y ISGENE HOMOD1 HOMOD0 VOMOD1 VOMOD0 CLMOD1 CLMOD0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 320 of 706 REJ09B0303-0300 Section 13 Timer Connection TCONRS is an 8-bit readable/writable register that selects 8-bit timer TMRX/TMRY access and the synchronization signal output signal source and generation method. TCONRS is initialized to H'00 by a reset and in hardware standby mode. Bit 7—TMRX/TMRY Access Select (TMRX/Y): The TMRX and TMRY registers can only be accessed when the HIE bit in SYSCR is cleared to 0. In the H8/3577 Group and H8/3567 Group, some of the TMRX registers and the TMRY registers are assigned to the same memory space addresses (H'FFF0 to H'FFF5), and the TMRX/Y bit determines which registers are accessed. Bit 7 TMRX/Y Description 0 The TMRX registers are accessed at addresses H'FFF0 to H'FFF5 1 The TMRY registers are accessed at addresses H'FFF0 to H'FFF5 (Initial value) Bit 6—Internal Synchronization Signal Select (ISGENE): Selects internal synchronization signals (IHG, IVG, and CL4 signals) as the signal sources for the IHO, IVO, and CLO signals. Bits 5 and 4—Horizontal Synchronization Output Mode Select 1 and 0 (HOMOD1, HOMOD0): These bits select the signal source and generation method for the IHO signal. Bit 6 Bit 5 Bit 4 ISGENE VOMOD1 VOMOD0 Description 0 0 0 The IHI signal (without 2fH modification) is selected 1 (Initial value) 1 The IHI signal (with 2fH modification) is selected 0 The CL1 signal is selected 1 1 0 0 The IHG signal is selected 1 1 0 1 Rev. 3.00 Mar 17, 2006 page 321 of 706 REJ09B0303-0300 Section 13 Timer Connection Bits 3 and 2—Vertical Synchronization Output Mode Select 1 and 0 (VOMOD1, VOMOD0): These bits select the signal source and generation method for the IVO signal. Bit 6 Bit 3 Bit 2 ISGENE VOMOD1 VOMOD0 Description 0 0 0 The IVI signal (without fall modification or IHI synchronization) is selected (Initial value) 1 The IVI signal (without fall modification, with IHI synchronization) is selected 0 The IVI signal (with fall modification, without IHI synchronization) is selected 1 The IVI signal (with fall modification and IHI synchronization) is selected 0 The IVG signal is selected 1 1 0 1 1 0 1 Bits 1 and 0—Clamp Waveform Mode Select 1 and 0 (CLMOD1, CLMOD0): These bits select the signal source for the CLO signal (clamp waveform). Bit 6 Bit 1 Bit 0 ISGENE CLMOD1 CLMOD2 Description 0 0 0 The CL1 signal is selected 1 The CL2 signal is selected 0 The CL3 signal is selected 1 1 1 0 0 The CL4 signal is selected 1 1 0 1 Rev. 3.00 Mar 17, 2006 page 322 of 706 REJ09B0303-0300 (Initial value) Section 13 Timer Connection 13.2.4 Edge Sense Register (SEDGR) Bit 7 6 5 4 3 2 1 0 VEDG HEDG CEDG HFEDG VFEDG PREQF Initial value 0 0 0 0 0 0 IHI 2 —* IVI 2 —* Read/Write 1 R/(W)* 1 R/(W)* 1 R/(W)* 1 R/(W)* 1 R/(W)* R/(W)* R R 1 Notes: 1. Only 0 can be written, to clear the flags. 2. The initial value is undefined since it depends on the pin states. SEDGR is an 8-bit readable/writable register used to detect a rising edge on the timer connection input pins and the occurrence of 2fH modification, and to determine the phase of the IVI and IHI signals. The upper 6 bits of SEDGR are initialized to 0 by a reset and in hardware standby mode. The initial value of the lower 2 bits is undefined, since it depends on the pin states. Bit 7—VSYNCI Edge (VEDG): Detects a rising edge on the VSYNCI pin. Bit 7 VEDG Description 0 [Clearing condition] When 0 is written in VEDG after reading VEDG = 1 1 [Setting condition] When a rising edge is detected on the VSYNCI pin (Initial value) Bit 6—HSYNCI Edge (HEDG): Detects a rising edge on the HSYNCI pin. Bit 6 HEDG Description 0 [Clearing condition] When 0 is written in HEDG after reading HEDG = 1 1 [Setting condition] When a rising edge is detected on the HSYNCI pin (Initial value) Rev. 3.00 Mar 17, 2006 page 323 of 706 REJ09B0303-0300 Section 13 Timer Connection Bit 5—CSYNCI Edge (CEDG): Detects a rising edge on the CSYNCI pin. Bit 5 CEDG Description 0 [Clearing condition] (Initial value) When 0 is written in CEDG after reading CEDG = 1 1 [Setting condition] When a rising edge is detected on the CSYNCI pin Bit 4—HFBACKI Edge (HFEDG): Detects a rising edge on the HFBACKI pin. Bit 4 HFEDG Description 0 [Clearing condition] (Initial value) When 0 is written in HFEDG after reading HFEDG = 1 1 [Setting condition] When a rising edge is detected on the HFBACKI pin Bit 3—VFBACKI Edge (VFEDG): Detects a rising edge on the VFBACKI pin. Bit 3 VFEDG Description 0 [Clearing condition] (Initial value) When 0 is written in VFEDG after reading VFEDG = 1 1 [Setting condition] When a rising edge is detected on the VFBACKI pin Bit 2—Pre-Equalization Flag (PREQF): Detects the occurrence of an IHI signal 2fH modification condition. The generation of a falling/rising edge in the IHI signal during a mask interval is expressed as the occurrence of a 2fH modification condition. For details, see section 13.3.4, IHI Signal 2fH Modification. Rev. 3.00 Mar 17, 2006 page 324 of 706 REJ09B0303-0300 Section 13 Timer Connection Bit 2 PREQF Description 0 [Clearing condition] (Initial value) When 0 is written in PREQF after reading PREQF = 1 1 [Setting condition] When an IHI signal 2fH modification condition is detected Bit 1—IHI Signal Level (IHI): Indicates the current level of the IHI signal. Signal source and phase inversion selection for the IHI signal depends on the contents of TCONRI. Read this bit to determine whether the input signal is positive or negative, then maintain the IHI signal at positive phase by modifying TCONRI. Bit 1 IHI Description 0 The IHI signal is low 1 The IHI signal is high Bit 0—IVI Signal Level (IVI): Indicates the current level of the IVI signal. Signal source and phase inversion selection for the IVI signal depends on the contents of TCONRI. Read this bit to determine whether the input signal is positive or negative, then maintain the IVI signal at positive phase by modifying TCONRI. Bit 0 IVI Description 0 The IVI signal is low 1 The IVI signal is high 13.2.5 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 325 of 706 REJ09B0303-0300 Section 13 Timer Connection MSTPCR, comprising two 8-bit readable/writable registers, performs module stop mode control. When the MSTP13, MSTP12, and MSTP8 bits are set to 1, the 16-bit free-running timer, 8-bit timer channels 0 and 1 and channels X and Y, and timer connection, respectively, halt and enter module stop mode at the end of the bus cycle. See section 21.5, Module Stop Mode, for details. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 5—Module Stop (MSTP13): Specifies FRT module stop mode. MSTPCRH Bit 5 MSTP13 Description 0 FRT module stop mode is cleared 1 FRT module stop mode is set (Initial value) MSTPCRH Bit 4—Module Stop (MSTP12): Specifies 8-bit timer channel 0 and 1 module stop mode. MSTPCRH Bit 4 MSTP12 Description 0 8-bit timer channel 0 and 1 module stop mode is cleared 1 8-bit timer channel 0 and 1 module stop mode is set (Initial value) MSTPCRH Bit 0—Module Stop (MSTP8): Specifies 8-bit timer channel X and Y and timer connection module stop mode. MSTPCRH Bit 0 MSTP8 Description 0 8-bit timer channel X and Y and timer connection module stop mode is cleared 1 8-bit timer channel X and Y and timer connection module stop mode is set (Initial value) Rev. 3.00 Mar 17, 2006 page 326 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3 Operation 13.3.1 PWM Decoding (PDC Signal Generation) The timer connection facility and TMRX can be used to decode a PWM signal in which 0 and 1 are represented by the pulse width. To do this, a signal in which a rising edge is generated at regular intervals must be selected as the IHI signal. The timer counter (TCNT) in TMRX is set to count the internal clock pulses and to be cleared on the rising edge of the external reset signal (IHI signal). The value to be used as the threshold for deciding the pulse width is written in TCORB. The PWM decoder contains a delay latch which uses the IHI signal as data and compare-match signal B (CMB) as a clock, and the state of the IHI signal (the result of the pulse width decision) at the compare-match signal B timing after TCNT is reset by the rise of the IHI signal is output as the PDC signal. The pulse width setting using TICRR and TICRF of TMRX can be used to determine the pulse width decision threshold. Examples of TCR and TCORB in TMRX settings are shown in tables 13.3 and 13.4, and the timing chart is shown in figure 13.2. Table 13.3 Examples of TCR Settings Bit(s) Abbreviation Contents Description 7 CMIEB 0 6 CMIEA 0 Interrupts due to compare-match and overflow are disabled 5 OVIE 0 4 and 3 CCLR1, CCLR0 11 TCNT is cleared by the rising edge of the external reset signal (IHI signal) 2 to 0 CKS2 to CKS0 001 Incremented on internal clock: φ Table 13.4 Examples of TCORB (Pulse Width Threshold) Settings φ:10 MHz φ: 12 MHz φ: 16 MHz φ: 20 MHz H'07 0.8 µs 0.67 µs 0.5 µs 0.4 µs H'0F 1.6 µs 1.33 µs 1 µs 0.8 µs H'1F 3.2 µs 2.67 µs 2 µs 1.6 µs H'3F 6.4 µs 5.33 µs 4 µs 3.2 µs H'7F 12.8 µs 10.67 µs 8 µs 6.4 µs Rev. 3.00 Mar 17, 2006 page 327 of 706 REJ09B0303-0300 Section 13 Timer Connection Judgment of IHI signal state in compare-match IHI signal PDC signal TCNT TCORB (threshold) Counter reset by IHI signal Counter clear upon TCNT overflow The IHI signal state is not judged in the 2nd compare-match. Figure 13.2 Timing Chart for PWM Decoding 13.3.2 Clamp Waveform Generation (CL1/CL2/CL3 Signal Generation) The timer connection facility and TMRX can be used to generate signals with different duty cycles and rising/falling edges (clamp waveforms) in synchronization with the input signal (IHI signal). Three clamp waveforms can be generated: the CL1, CL2, and CL3 signals. In addition, the CL4 signal can be generated using TMRY. The CL1 signal rises simultaneously with the rise of the IHI signal, and when the CL1 signal is high, the CL2 signal rises simultaneously with the fall of the IHI signal. The fall of both the CL1 and the CL2 signal can be specified by TCORA. The rise of the CL3 signal can be specified as simultaneous with the sampling of the fall of the IHI signal using the system clock, and the fall of the CL3 signal can be specified by TCORC. The CL3 signal falls at the rise of the IHI signal. TCNT in TMRX is set to count internal clock pulses and to be cleared on the rising edge of the external reset signal (IHI signal). The value to be used as the CL1 signal pulse width is written in TCORA. Write a value of H'02 or more in TCORA when internal clock φ is selected as the TMRX counter clock, and a value or H'01 or more when φ/2 is selected. When internal clock φ is selected, the CL1 signal pulse width is (TCORA set value + 3 ± 0.5). When the CL2 signal is used, the setting must be made so that this pulse width is greater than the IHI signal pulse width. The value to be used as the CL3 signal pulse width is written in TCORC. The TICR register in TMRX captures the value of TCNT at the inverse of the external reset signal edge (in this case, the falling edge of the IHI signal). The timing of the fall of the CL3 signal is determined by the sum of Rev. 3.00 Mar 17, 2006 page 328 of 706 REJ09B0303-0300 Section 13 Timer Connection the contents of TICR and TCORC. Caution is required if the rising edge of the IHI signal precedes the fall timing set by the contents of TCORC, since the IHI signal will cause the CL3 signal to fall. Examples of TMRX TCR settings are the same as those in table 13.3. The clamp waveform timing charts are shown in figures 13.3 and 13.4. Since the rise of the CL1 and CL2 signals is synchronized with the edge of the IHI signal, and their fall is synchronized with the system clock, the pulse width variation is equivalent to the resolution of the system clock. Both the rise and the fall of the CL3 signal are synchronized with the system clock and the pulse width is fixed, but there is a variation in the phase relationship with the IHI signal equivalent to the resolution of the system clock. IHI signal CL1 signal CL2 signal TCNT TCORA Figure 13.3 Timing Chart for Clamp Waveform Generation (CL1 and CL2 Signals) IHI signal CL3 signal TCNT TICR+TCORC TICR Figure 13.4 Timing Chart for Clamp Waveform Generation (CL3 Signal) Rev. 3.00 Mar 17, 2006 page 329 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3.3 Measurement of 8-Bit Timer Divided Waveform Period The timer connection facility, TMR1, and the free-running timer (FRT) can be used to measure the period of an IHI signal divided waveform. Since TMR1 can be cleared by a rising edge of the IVI signal, the rise and fall of the IHI signal divided waveform can be virtually synchronized with the IVI signal. This enables period measurement to be carried out efficiently. To measure the period of an IHI signal divided waveform, TCNT in TMR1 is set to count the external clock (IHI signal) pulses and to be cleared on the rising edge of the external reset signal (IVI signal). The value to be used as the division factor is written in TCORA, and the TMO output method is specified by the OS bits in TCSR. Examples of TMR1 TCR and TCSR settings are shown in table 13.5, and the timing chart for measurement of the IVI signal and IHI signal divided waveform periods is shown in figure 13.5. The period of the IHI signal divided waveform is given by (ICRD(3) – ICRD(2)) × the resolution. Rev. 3.00 Mar 17, 2006 page 330 of 706 REJ09B0303-0300 Section 13 Timer Connection Table 13.5 Examples of TCR and TCSR Settings Register Bit(s) Abbreviation Contents Description TCR in TMR1 7 CMIEB 0 6 CMIEA 0 Interrupts due to compare-match and overflow are disabled 5 OVIE 0 4, 3 CCLR1, CCLR0 11 TCNT is cleared by the rising edge of the external reset signal (IVI signal) 2 to 0 CKS2 to CKS0 101 TCNT is incremented on the rising edge of the external clock (IHI signal) 3 to 0 OS3 to OS0 0011 Not changed by compare-match B; output inverted by compare-match A (toggle output): division by 512 TCSR in TMR1 1001 TCR in FRT 6 IEDGB 0/1 or when TCORB < TCORA, 1 output on compare-match B, and 0 output on compare-match A: division by 256 0: FRC value is transferred to ICRB on falling edge of input capture input B (IHI divided signal waveform) 1: FRC value is transferred to ICRB on rising edge of input capture input B (IHI divided signal waveform) TCSR in FRT 1, 0 CKS1, CKS0 01 FRC is incremented on internal clock: φ/8 0 CCLRA 0 FRC clearing is disabled Rev. 3.00 Mar 17, 2006 page 331 of 706 REJ09B0303-0300 Section 13 Timer Connection IVI signal IHI signal divided waveform ICRB(4) ICRB(3) ICRB(2) ICRB(1) FRC ICRB Figure 13.5 Timing Chart for Measurement of IVI Signal and IHI Signal Divided Waveform Periods 13.3.4 IHI Signal and 2fH Modification By using the timer connection FRT, even if there is a part of the IHI signal with twice the frequency, this can be eliminated. In order for this function to operate properly, the duty cycle of the IHI signal must be approximately 30% or less, or approximately 70% or above. The 8-bit OCRDM contents or twice the OCRDM contents can be added automatically to the data captured in ICRD in the FRT, and compare-matches generated at these points. The interval between the two compare-matches is called a mask interval. A value equivalent to approximately 1/3 the IHI signal period is written in OCRDM. ICRD is set so that capture is performed on the rise of the IHI signal. Since the IHI signal supplied to the IHO signal selection circuit is normally set on the rise of the IHI signal and reset on the fall, its waveform is the same as that of the original IHI signal. When 2fH modification is selected, IHI signal edge detection is disabled during mask intervals. Capture is also disabled during these intervals. Examples of FRT TCR settings are shown in table 13.6, and the 2fH modification timing chart is shown in figure 13.6. Rev. 3.00 Mar 17, 2006 page 332 of 706 REJ09B0303-0300 Section 13 Timer Connection Table 13.6 Examples of TCR, TCSR, TCOR, and OCRDM Settings Register Bit(s) Abbreviation Contents Description TCR in FRT 4 IEDGD 1 FRC value is transferred to ICRD on the rising edge of input capture input D (IHI signal) 1, 0 CKS1, CKS0 01 FRC is incremented on internal clock: φ/8 TCSR in FRT 0 CCLRA 0 FRC clearing is disabled TCOR in FRT 7 ICRDMS 1 ICRD is set to the operating mode in which OCRDM is used OCRDM7 to OCRDM0 H'01 to H'FF Specifies the period during which ICRD operation is masked OCRDM in FRT 7 to 0 IHI signal (without 2fH modification) IHI signal (with 2fH modification) Mask interval ICRD + OCRDM × 2 ICRD + OCRDM FRC ICRD Figure 13.6 2fH Modification Timing Chart Rev. 3.00 Mar 17, 2006 page 333 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3.5 IVI Signal Fall Modification and IHI Synchronization By using the timer connection TMR1, the fall of the IVI signal can be shifted backward by the specified number of IHI signal waveforms. Also, the fall of the IVI signal can be synchronized with the rise of the IHI signal. To perform 8-bit timer divided waveform period measurement, TCNT in TMR1 is set to count external clock (IHI signal) pulses, and to be cleared on the rising edge of the external reset signal (inverse of the IVI signal). The number of IHI signal pulses until the fall of the IVI signal is written in TCORB. Since the IVI signal supplied to the IVO signal selection circuit is normally set on the rise of the IVI signal and reset on the fall, its waveform is the same as that of the original IVI signal. When fall modification is selected, a reset is performed on a TMR1 TCORB compare-match. The fall of the waveform generated in this way can be synchronized with the rise of the IHI signal, regardless of whether or not fall modification is selected. Examples of TMR1 TCORB, TCR, and TCSR settings are shown in table 13.7, and the fall modification/IHI synchronization timing chart is shown in figure 13.7. Rev. 3.00 Mar 17, 2006 page 334 of 706 REJ09B0303-0300 Section 13 Timer Connection Table 13.7 Examples of TCORB, TCR, and TCSR Settings Register Bit(s) Abbreviation Contents Description TCR in TMR1 7 CMIEB 0 6 CMIEA 0 Interrupts due to compare-match and overflow are disabled 5 OVIE 0 4, 3 CCLR1, CCLR0 11 TCNT is cleared by the rising edge of the external reset signal (inverse of the IVI signal) 2 to 0 CKS2 to CKS0 101 TCNT is incremented on the rising edge of the external clock (IHI signal) 3 to 0 OS3 to OS0 0011 Not changed by compare-match B; output inverted by compare-match A (toggle output) TCSR in TMR1 1001 TOCRB in TMR1 H'03 (example) or when TCORB < TCORA, 1 output on compare-match B, 0 output on comparematch A Compare-match on the 4th (example) rise of the IHI signal after the rise of the inverse of the IVI signal IHI signal IVI signal (PDC signal) IVO signal (without fall modification, with IHI synchronization) IVO signal (with fall modification, without IHI synchronization) IVO signal (with fall modification and IHI synchronization) TCNT 0 1 2 3 4 5 TCNT = TCORB (3) Figure 13.7 Fall Modification/IHI Synchronization Timing Chart Rev. 3.00 Mar 17, 2006 page 335 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3.6 Internal Synchronization Signal Generation (IHG/IVG/CL4 Signal Generation) By using the timer connection FRT and TMRY, it is possible to automatically generate internal signals (IHG and IVG signals) corresponding to the IHI and IVI signals. As the IHG signal is synchronized with the rise of the IVG signal, the IHG signal period must be made a divisor of the IVG signal period in order to keep it constant. In addition, the CL4 signal can be generated in synchronization with the IHG signal. The contents of OCRA in the FRT are updated by the automatic addition of the contents of OCRAR or OCRAF, alternately, each time a compare-match occurs. A value corresponding to the 0 interval of the IVG signal is written in OCRAR, and a value corresponding to the 1 interval of the IVG signal is written in OCRAF. The IVG signal is set by a compare-match after an OCRAR addition, and reset by a compare-match after an OCRAF addition. The IHG signal is the TMRY 8-bit timer output. TMRY is set to count internal clock pulses, and to be cleared on TCORA compare-match, to fix the period and set the timer output. TCORB is set so as to reset the timer output. The IVG signal is connected as the TMRY reset input (TMRI), and the rise of the IVG signal can be treated in the same way as a TCORA compare-match. The CL4 signal is a waveform that rises within one system clock period after the fall of the IHG signal, and has a 1 interval of 6 system clock periods. Examples of settings of TCORA, TCORB, TCR, and TCSR in TMRY, and OCRAR, OCRAF, and TCR in the FRT, are shown in table 13.8, and the IHG signal/IVG signal timing chart is shown in figure 13.8. Rev. 3.00 Mar 17, 2006 page 336 of 706 REJ09B0303-0300 Section 13 Timer Connection Table 13.8 Examples of OCRAR, OCRAF, TOCR, TCORA, TCORB, TCR, and TCSR Settings Register Bit(s) Abbreviation Contents Description TCR in TMRY 7 CMIEB 0 6 CMIEA 0 Interrupts due to compare-match and overflow are disabled 5 OVIE 0 4, 3 CCLR1, CCLR0 01 2 to 0 CKS2 to CKS0 001 TCNT is incremented on internal clock: φ/4 3 to 0 OS3 to OS0 0110 0 output on compare-match B 1 output on compare-match A TOCRA in TMRY H'3F (example) IHG signal period = φ × 256 TOCRB in TMRY H'03 (example) IHG signal 1 interval = φ × 16 01 FRC is incremented on internal clock: φ/8 OCRAR in FRT H'7FEF (example) IVG signal 0 interval = φ × 262016 OCRAF in FRT H'000F (example) IVG signal 1 interval = φ × 128 1 OCRA is set to the operating mode in which OCRAR and OCRAF are used TCSR in TMRY TCR in FRT TOCR in FRT 1, 0 6 CKS1, CKS0 OCRAMS TCNT is cleared by compare-match A IVG signal period = φ × 262144 (1024 times IHG signal) Rev. 3.00 Mar 17, 2006 page 337 of 706 REJ09B0303-0300 Section 13 Timer Connection IVG signal OCRA (1) = OCRA (0) + OCRAF OCRA (2) = OCRA (1) + OCRAR OCRA (3) = OCRA (2) + OCRAF OCRA (4) = OCRA (3) + OCRAR OCRA FRC 6 system clocks 6 system clocks 6 system clocks CL4 signal IHG signal TCORA TCORB TCNT Figure 13.8 IVG Signal/IHG Signal/CL4 Signal Timing Chart Rev. 3.00 Mar 17, 2006 page 338 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3.7 HSYNCO Output With the HSYNCO output, the meaning of the signal source to be selected and use or non-use of modification varies according to the IHI signal source and the waveform required by external circuitry. The meaning of the HSYNCO output in each mode is shown in table 13.9. Table 13.9 Meaning of HSYNCO Output in Each Mode Mode IHI Signal IHO Signal Meaning of IHO Signal No signal HFBACKI input IHI signal (without 2fH modification) HFBACKI input is output directly IHI signal (with 2fH modification) Meaningless unless there is a double-frequency part in the HFBACKI input CL1 signal HFBACKI input 1 interval is changed before output IHG signal Internal synchronization signal is output IHI signal (without 2fH modification) CSYNCI input (composite synchronization signal) is output directly IHI signal (with 2fH modification) Double-frequency part of CSYNCI input (composite synchronization signal) is eliminated before output CL1 signal CSYNCI input (composite synchronization signal) horizontal synchronization signal part is separated before output IHG signal Internal synchronization signal is output IHI signal (without 2fH modification) HSYNCI input (composite synchronization signal) is output directly IHI signal (with 2fH modification) Double-frequency part of HSYNCI input (composite synchronization signal) is eliminated before output CL1 signal HSYNCI input (composite synchronization signal) horizontal synchronization signal part is separated before output IHG signal Internal synchronization signal is output IHI signal (without 2fH modification) HSYNCI input (horizontal synchronization signal) is output directly IHI signal (with 2fH modification) Meaningless unless there is a double-frequency part in the HSYNCI input (horizontal synchronization signal) CL1 signal HSYNCI input (horizontal synchronization signal) 1 interval is changed before output IHG signal Internal synchronization signal is output S-on-G mode CSYNCI input Composite HSYNCI mode input Separate mode HSYNCI input Rev. 3.00 Mar 17, 2006 page 339 of 706 REJ09B0303-0300 Section 13 Timer Connection 13.3.8 VSYNCO Output With the VSYNCO output, the meaning of the signal source to be selected and use or non-use of modification varies according to the IVI signal source and the waveform required by external circuitry. The meaning of the VSYNCO output in each mode is shown in table 13.10. Table 13.10 Meaning of VSYNCO Output in Each Mode Mode IVI Signal IVO Signal Meaning of IVO Signal No signal VFBACKI input IVI signal (without fall modification or IHI synchronization) VFBACKI input is output directly IVI signal (without fall modification, with IHI synchronization) Meaningless unless VFBACKI input is synchronized with HFBACKI input IVI signal (with fall modification, without IHI synchronization) VFBACKI input fall is modified before output IVI signal (with fall modification and IHI synchronization) VFBACKI input fall is modified and signal is synchronized with HFBACKI input before output IVG signal Internal synchronization signal is output IVI signal (without fall modification or IHI synchronization) CSYNCI/HSYNCI input (composite synchronization signal) vertical synchronization signal part is separated before output IVI signal (without fall modification, with IHI synchronization) CSYNCI/HSYNCI input (composite synchronization signal) vertical synchronization signal part is separated, and signal is synchronized with CSYNCI/HSYNCI input before output IVI signal (with fall modification, without IHI synchronization) CSYNCI/HSYNCI input (composite synchronization signal) vertical synchronization signal part is separated, and fall is modified before output IVI signal (with fall modification and IHI synchronization) CSYNCI/HSYNCI input (composite synchronization signal) vertical synchronization signal part is separated, fall is modified, and signal is synchronized with CSYNCI/HSYNCI input before output IVG signal Internal synchronization signal is output S-on-G PDC signal mode or composite mode Rev. 3.00 Mar 17, 2006 page 340 of 706 REJ09B0303-0300 Section 13 Timer Connection Mode IVI Signal IVO Signal Meaning of IVO Signal Separate mode VSYNCI input IVI signal (without fall modification or IHI synchronization) VSYNCI input (vertical synchronization signal) is output directly IVI signal (without fall modification, with IHI synchronization) Meaningless unless VSYNCI input (vertical synchronization signal) is synchronized with HSYNCI input (horizontal synchronization signal) IVI signal (with fall modification, without IHI synchronization) VSYNCI input (vertical synchronization signal) fall is modified before output IVI signal (with fall modification and IHI synchronization) VSYNCI input (vertical synchronization signal) fall is modified and signal is synchronized with HSYNCI input (horizontal synchronization signal) before output IVG signal Internal synchronization signal is output 13.3.9 CBLANK Output Using the signals generated/selected with timer connection, it is possible to generate a waveform based on the composite synchronization signal (blanking waveform). One kind of blanking waveform is generated by combining HFBACKI and VFBACKI inputs, with the phase polarity made positive by means of bits HFINV and VFINV in TCONRI, with the IVO signal. The composition logic is shown in figure 13.9. HFBACKI input (positive) VFBACKI input (positive) Falling edge sensing Reset Rising edge sensing Set Q CBLANK signal (positive) IVO signal (positive) Figure 13.9 CBLANK Output Waveform Generation Rev. 3.00 Mar 17, 2006 page 341 of 706 REJ09B0303-0300 Section 13 Timer Connection Rev. 3.00 Mar 17, 2006 page 342 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) Section 14 Watchdog Timer (WDT) 14.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip watchdog timer (WDT0). The WDT outputs an overflow signal if a system crash prevents the CPU from writing to the timer counter, allowing it to overflow. At the same time, the WDT can also generate an internal reset signal or internal NMI interrupt signal. When this watchdog function is not needed, the WDT can be used as an interval timer. In interval timer mode, an interval timer interrupt is generated each time the counter overflows. 14.1.1 Features • Switchable between watchdog timer mode and interval timer mode WOVI interrupt generation in interval timer mode • Internal reset or internal interrupt generated when the timer counter overflows Choice of internal reset or NMI interrupt generation in watchdog timer mode • Choice of 8 counter input clocks Maximum WDT interval: system clock period × 131072 × 256 Rev. 3.00 Mar 17, 2006 page 343 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) 14.1.2 Block Diagram Figure 14.1 shows block diagram of WDT0. Internal NMI interrupt request signal Interrupt control Overflow Clock φ/2 φ/64 φ/128 φ/512 φ/2048 φ/8192 φ/32768 φ/131072 Clock select Reset control Internal reset signal* Internal clock source TCNT TCSR Module bus Bus interface WDT Legend: TCSR: Timer control/status register TCNT: Timer counter Note: * The internal reset signal can be generated by means of a register setting. Figure 14.1 Block Diagram of WDT0 Rev. 3.00 Mar 17, 2006 page 344 of 706 REJ09B0303-0300 Internal bus WOVI (interrupt request signal) Section 14 Watchdog Timer (WDT) 14.1.3 Register Configuration The WDT has four registers, as summarized in table 14.1. These registers control clock selection, WDT mode switching, the reset signal, etc. Table 14.1 WDT Registers Address Channel Name 0 Common Abbreviation R/W Initial Value Write* H'00 H'FFA8 H'FFA8 1 Read Timer control/status register 0 TCSR0 R/(W)* Timer counter 0 TCNT0 R/W H'00 H'FFA8 H'FFA9 System control register SYSCR R/W H'09 H'FFC4 H'FFC4 2 Notes: 1. For details of write operations, see section 14.2.4, Notes on Register Access. 2. Only 0 can be written in bit 7, to clear the flag. 14.2 Register Descriptions 14.2.1 Timer Counter (TCNT) Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TCNT is an 8-bit readable/writable* up-counter. When the TME bit is set to 1 in TCSR, TCNT starts counting pulses generated from the internal clock source selected by bits CKS2 to CKS0 in TCSR. When the TCNT value overflows (changes from H'FF to H'00), the OVF flag in TCSR is set to 1. TCNT is initialized to H'00 by a reset, in hardware standby mode, or when the TME bit is cleared to 0. It is not initialized in software standby mode. Note: * The method of writing to TCNT is more complicated than for most other registers, to prevent accidental overwriting. For details see section 14.2.4, Notes on Register Access. Rev. 3.00 Mar 17, 2006 page 345 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) 14.2.2 Timer Control/Status Register (TCSR0) Bit 7 6 5 4 3 2 1 0 OVF WT/IT TME RSTS RST/NMI CKS2 CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/W R/W R/W R/W R/W R/W R/W Note: * Only 0 can be written, to clear the flag. TCSR is an 8-bit readable/writable* register. Its functions include selecting the clock source to be input to TCNT, and the timer mode. TCSR is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Note: * The method of writing to TCSR is more complicated than for most other registers, to prevent accidental overwriting. For details see section 14.2.4, Notes on Register Access. Bit 7—Overflow Flag (OVF): A status flag that indicates that TCNT has overflowed from H'FF to H'00. Bit 7 OVF Description 0 [Clearing conditions] 1 • Write 0 in the TME bit • Read TCSR when OVF = 1*, then write 0 in OVF (Initial value) [Setting condition] When TCNT overflows (changes from H'FF to H'00) (When internal reset request generation is selected in watchdog timer mode, OVF is cleared automatically by the internal reset.) Note: * When the interval timer interrupt is disabled and OVF is polled, reading OVF while set to 1 should be performed at least twice. Rev. 3.00 Mar 17, 2006 page 346 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) Bit 6—Timer Mode Select (WT/IT IT): IT Selects whether the WDT is used as a watchdog timer or interval timer. If used as an interval timer, the WDT generates an interval timer interrupt request (WOVI) when TCNT overflows. If used as a watchdog timer, the WDT generates a reset or NMI interrupt when TCNT overflows. Bit 6 WT/IT IT Description 0 Interval timer: Sends the CPU an interval timer interrupt request (WOVI) when TCNT overflows (Initial value) 1 Watchdog timer: Generates a reset or NMI interrupt when TCNT overflows Bit 5—Timer Enable (TME): Selects whether TCNT runs or is halted. Bit 5 TME Description 0 TCNT is initialized to H'00 and halted 1 TCNT counts (Initial value) TCSR0 Bit 4—Reset Select (RSTS): Reserved. This bit should not be set to 1. Bit 3—Reset or NMI (RST/NMI NMI): NMI Specifies whether an internal reset or NMI interrupt is requested on TCNT overflow in watchdog timer mode. Bit 3 RST/NMI NMI Description 0 An NMI interrupt is requested 1 An internal reset is requested (Initial value) Rev. 3.00 Mar 17, 2006 page 347 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) Bits 2 to 0—Clock Select 2 to 0 (CKS2 to CKS0): These bits select the clock to be input to TCNT from internal clocks obtained by dividing the system clock. Bit 2 Bit 1 Bit 0 CKS2 CKS1 CKS0 Clock Overflow Period* (when φ = 20 MHz) 0 0 0 φ/2 (Initial value) 25.6 µs 1 φ/64 819.2 µs 0 φ/128 1.6 ms 1 φ/512 6.6 ms 0 φ/2048 26.2 ms 1 φ/8192 104.9 ms 0 φ/32768 419.4 ms 1 φ/131072 1.68 s 1 1 0 1 Note: 14.2.3 Description The overflow period is the time from when TCNT starts counting up from H'00 until overflow occurs. * System Control Register (SYSCR) Bit 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W Only bit 3 is described here. For details on functions not related to the watchdog timer, see sections 3.2.2 and 5.2.1, System Control Register (SYSCR), and the descriptions of the relevant modules. Bit 3—External Reset (XRST): Indicates the reset source. When the watchdog timer is used, a reset can be generated by watchdog timer overflow in addition to external reset input. XRST is a read-only bit. It is set to 1 by an external reset, and cleared to 0 by watchdog timer overflow. Bit 3 XRST Description 0 Reset is generated by watchdog timer overflow 1 Reset is generated by external reset input Rev. 3.00 Mar 17, 2006 page 348 of 706 REJ09B0303-0300 (Initial value) Section 14 Watchdog Timer (WDT) 14.2.4 Notes on Register Access The watchdog timer’s TCNT and TCSR registers differ from other registers in being more difficult to write to. The procedures for writing to and reading these registers are given below. Writing to TCNT and TCSR: These registers must be written to by a word transfer instruction. They cannot be written to with byte transfer instructions. Figure 14.2 shows the format of data written to TCNT and TCSR. TCNT and TCSR both have the same write address. For a write to TCNT, the upper byte of the written word must contain H'5A and the lower byte must contain the write data. For a write to TCSR, the upper byte of the written word must contain H'A5 and the lower byte must contain the write data. This transfers the write data from the lower byte to TCNT or TCSR. TCNT write 15 8 7 H'5A Address: H'FFA8 0 Write data TCSR write 15 Address: H'FFA8 8 7 H'A5 0 Write data Figure 14.2 Format of Data Written to TCNT and TCSR Reading TCNT and TCSR: These registers are read in the same way as other registers. The read addresses are H'FFA8 for TCSR, and H'FFA9 for TCNT. 14.3 Operation 14.3.1 Watchdog Timer Operation To use the WDT as a watchdog timer, set the WT/IT and TME bits in TCSR to 1. Software must prevent TCNT overflows by rewriting the TCNT value (normally by writing H'00) before overflow occurs. This ensures that TCNT does not overflow while the system is operating normally. If TCNT overflows without being rewritten because of a system crash or other error, an internal reset or NMI interrupt request is generated. When the RST/NMI bit is set to 1, the chip is reset for 518 system clock periods (518 φ) by a counter overflow. This is illustrated in figure 14.3. Rev. 3.00 Mar 17, 2006 page 349 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) An internal reset request from the watchdog timer and reset input from the RES pin are handled via the same vector. The reset source can be identified from the value of the XRST bit in SYSCR. If a reset caused by an input signal from the RES pin and a reset caused by WDT overflow occur simultaneously, the RES pin reset has priority, and the XRST bit in SYSCR is set to 1. An NMI interrupt request from the watchdog timer and an interrupt request from the NMI pin are handled via the same vector. Simultaneous handling of a watchdog timer NMI interrupt request and an NMI pin interrupt request must therefore be avoided. TCNT value Overflow H'FF Time H'00 WT/IT = 1 TME = 1 H'00 written to TCNT OVF = 1* WT/IT = 1 H'00 written TME = 1 to TCNT Internal reset generated Internal reset signal 518 system clock periods Legend: WT/IT: Timer mode select bit TME: Timer enable bit Note: * Cleared to 0 by an internal reset when OVF is set to 1. XRST is cleared to 0. Figure 14.3 Operation in Watchdog Timer Mode 14.3.2 Interval Timer Operation To use the WDT as an interval timer, clear the WT/IT bit in TCSR to 0 and set the TME bit to 1. An interval timer interrupt (WOVI) is generated each time TCNT overflows, provided that the WDT is operating as an interval timer, as shown in figure 14.4. This function can be used to generate interrupt requests at regular intervals. Rev. 3.00 Mar 17, 2006 page 350 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) TCNT count Overflow H'FF Overflow Overflow Overflow Time H'00 WT/IT = 0 TME = 1 WOVI WOVI WOVI WOVI Legend: WOVI: Interval timer interrupt request generation Figure 14.4 Operation in Interval Timer Mode 14.3.3 Timing of Setting of Overflow Flag (OVF) The OVF bit in TCSR is set to 1 if TCNT overflows during interval timer operation. At the same time, an interval timer interrupt (WOVI) is requested. This timing is shown in figure 14.5. If NMI request generation is selected in watchdog timer mode, when TCNT overflows the OVF bit in TCSR is set to 1 and at the same time an NMI interrupt is requested. φ TCNT H'FF H'00 Overflow signal (internal signal) OVF Figure 14.5 Timing of OVF Setting Rev. 3.00 Mar 17, 2006 page 351 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) 14.4 Interrupts During interval timer mode operation, an overflow generates an interval timer interrupt (WOVI). The interval timer interrupt is requested whenever the OVF flag is set to 1 in TCSR. OVF must be cleared to 0 in the interrupt handling routine. When NMI interrupt request generation is selected in watchdog timer mode, an overflow generates an NMI interrupt request. 14.5 Usage Notes 14.5.1 Contention between Timer Counter (TCNT) Write and Increment If a timer counter clock pulse is generated during the T2 state of a TCNT write cycle, the write takes priority and the timer counter is not incremented. Figure 14.6 shows this operation. TCNT write cycle T1 T2 T3 φ Address Internal write signal TCNT input clock TCNT N M Counter write data Figure 14.6 Contention between TCNT Write and Increment Rev. 3.00 Mar 17, 2006 page 352 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) 14.5.2 Changing Value of CKS2 to CKS0 If bits CKS2 to CKS0 in TCSR are written to while the WDT is operating, errors could occur in the incrementation. Software must stop the watchdog timer (by clearing the TME bit to 0) before changing the value of bits CKS2 to CKS0. 14.5.3 Switching between Watchdog Timer Mode and Interval Timer Mode If the mode is switched from watchdog timer to interval timer, or vice versa, while the WDT is operating, errors could occur in the incrementation. Software must stop the watchdog timer (by clearing the TME bit to 0) before switching the mode. Rev. 3.00 Mar 17, 2006 page 353 of 706 REJ09B0303-0300 Section 14 Watchdog Timer (WDT) Rev. 3.00 Mar 17, 2006 page 354 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Section 15 Serial Communication Interface (SCI) 15.1 Overview The H8/3577 Group and H8/3567 Group are equipped with a single-channel serial communication interface (SCI). The SCI can handle both asynchronous and clocked synchronous serial communication. A function is also provided for serial communication between processors (multiprocessor communication function). 15.1.1 Features SCI features are listed below. • Choice of asynchronous or synchronous serial communication mode Asynchronous mode Serial data communication is executed using an asynchronous system in which synchronization is achieved character by character Serial data communication can be carried out with standard asynchronous communication chips such as a Universal Asynchronous Receiver/Transmitter (UART) or Asynchronous Communication Interface Adapter (ACIA) A multiprocessor communication function is provided that enables serial data communication with a number of processors Choice of 12 serial data transfer formats Data length: 7 or 8 bits Stop bit length: 1 or 2 bits Parity: Even, odd, or none Multiprocessor bit: 1 or 0 Receive error detection: Parity, overrun, and framing errors Break detection: Break can be detected by reading the RxD pin level directly in case of a framing error Synchronous mode Serial data communication is synchronized with a clock Serial data communication can be carried out with other chips that have a synchronous communication function One serial data transfer format Data length: 8 bits Receive error detection: Overrun errors detected Rev. 3.00 Mar 17, 2006 page 355 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) • Full-duplex communication capability The transmitter and receiver are mutually independent, enabling transmission and reception to be executed simultaneously Double-buffering is used in both the transmitter and the receiver, enabling continuous transmission and continuous reception of serial data • LSB-first or MSB-first transfer can be selected This selection can be made regardless of the communication mode (with the exception of 7-bit data transfer in asynchronous mode)* Note: * LSB-first transfer is used in the examples in this section. • Built-in baud rate generator allows any bit rate to be selected • Choice of serial clock source: internal clock from baud rate generator or external clock from SCK pin • Four interrupt sources Four interrupt sources (transmit-data-empty, transmit-end, receive-data-full, and receive error) that can issue requests independently Rev. 3.00 Mar 17, 2006 page 356 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.1.2 Block Diagram Bus interface Figure 15.1 shows a block diagram of the SCI. Module data bus RxD TxD RDR TDR RSR TSR BRR φ Baud rate generator Transmission/ reception control Parity generation Parity check SCK Legend: RSR: RDR: TSR: TDR: SMR: SCR: SSR: SCMR: BRR: SCMR SSR SCR SMR Internal data bus φ/4 φ/16 φ/64 Clock External clock TEI TXI RXI ERI Receive shift register Receive data register Transmit shift register Transmit data register Serial mode register Serial control register Serial status register Serial interface mode register Bit rate register Figure 15.1 Block Diagram of SCI Rev. 3.00 Mar 17, 2006 page 357 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.1.3 Pin Configuration Table 15.1 shows the serial pins used by the SCI. Table 15.1 SCI Pins Channel Pin Name Symbol I/O Function 0 Serial clock pin 0 SCK0 I/O SCI0 clock input/output Receive data pin 0 RxD0 Input SCI0 receive data input Transmit data pin 0 TxD0 Output SCI0 transmit data output Note: The abbreviations SCK, RxD, and TxD are used in the text, omitting the channel number. 15.1.4 Register Configuration The SCI has the internal registers shown in table 15.2. These registers are used to specify asynchronous mode or synchronous mode, the data format, and the bit rate, and to control the transmitter/receiver. Table 15.2 SCI Registers Channel Name Abbreviation R/W Initial Value Address 0 Serial mode register 0 SMR0 R/W H'00 Bit rate register 0 BRR0 R/W H'FF Common H'FFD8* 2 H'FFD9* 2 Serial control register 0 SCR0 R/W H'00 H'FFDA Transmit data register 0 TDR0 R/W H'FF H'FFDB Serial status register 0 SSR0 R/(W)* H'84 H'FFDC Receive data register 0 RDR0 R H'00 Serial interface mode register 0 SCMR0 R/W H'F2 H'FFDD 3 H'FFDE* Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 1 Notes: 1. Only 0 can be written, to clear flags. 2. Some serial communication interface registers are assigned to the same addresses as other registers. In this case, register selection is performed by the IICE bit in the serial timer control register (STCR). Rev. 3.00 Mar 17, 2006 page 358 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.2 Register Descriptions 15.2.1 Receive Shift Register (RSR) Bit 7 6 5 4 3 2 1 0 Read/Write — — — — — — — — RSR is a register used to receive serial data. The SCI sets serial data input from the RxD pin in RSR in the order received, starting with the LSB (bit 0), and converts it to parallel data. When one byte of data has been received, it is transferred to RDR automatically. RSR cannot be directly read or written to by the CPU. 15.2.2 Receive Data Register (RDR) Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R RDR is a register that stores received serial data. When the SCI has received one byte of serial data, it transfers the received serial data from RSR to RDR where it is stored, and completes the receive operation. After this, RSR is receive-enabled. Since RSR and RDR function as a double buffer in this way, continuous receive operations can be performed. RDR is a read-only register, and cannot be written to by the CPU. RDR is initialized to H'00 by a reset, and in standby mode, and module stop mode. Rev. 3.00 Mar 17, 2006 page 359 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.2.3 Transmit Shift Register (TSR) Bit 7 6 5 4 3 2 1 0 Read/Write — — — — — — — — TSR is a register used to transmit serial data. To perform serial data transmission, the SCI first transfers transmit data from TDR to TSR, then sends the data to the TxD pin starting with the LSB (bit 0). When transmission of one byte is completed, the next transmit data is transferred from TDR to TSR, and transmission started, automatically. However, data transfer from TDR to TSR is not performed if the TDRE bit in SSR is set to 1. TSR cannot be directly read or written to by the CPU. 15.2.4 Transmit Data Register (TDR) Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W TDR is an 8-bit register that stores data for serial transmission. When the SCI detects that TSR is empty, it transfers the transmit data written in TDR to TSR and starts serial transmission. Continuous serial transmission can be carried out by writing the next transmit data to TDR during serial transmission of the data in TSR. TDR can be read or written to by the CPU at all times. TDR is initialized to H'FF by a reset, and in standby mode, and module stop mode. 15.2.5 Serial Mode Register (SMR) Bit 7 6 5 4 3 2 1 0 C/A CHR PE O/E STOP MP CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 360 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) SMR is an 8-bit register used to set the SCI’s serial transfer format and select the baud rate generator clock source. SMR can be read or written to by the CPU at all times. SMR is initialized to H'00 by a reset, and in standby mode, and module stop mode. Bit 7—Communication Mode (C/A A): Selects asynchronous mode or synchronous mode as the SCI operating mode. Bit 7 C/A A Description 0 Asynchronous mode 1 Synchronous mode (Initial value) Bit 6—Character Length (CHR): Selects 7 or 8 bits as the data length in asynchronous mode. In synchronous mode, a fixed data length of 8 bits is used regardless of the CHR setting. Bit 6 CHR Description 0 8-bit data 7-bit data* 1 Note: * (Initial value) When 7-bit data is selected, the MSB (bit 7) of TDR is not transmitted, and LSBfirst/MSB-first selection is not available. Bit 5—Parity Enable (PE): In asynchronous mode, selects whether or not parity bit addition is performed in transmission, and parity bit checking in reception. In synchronous mode, or when a multiprocessor format is used, parity bit addition and checking is not performed, regardless of the PE bit setting. Bit 5 PE Description 0 Parity bit addition and checking disabled Parity bit addition and checking enabled* 1 Note: * (Initial value) When the PE bit is set to 1, the parity (even or odd) specified by the O/E bit is added to transmit data before transmission. In reception, the parity bit is checked for the parity (even or odd) specified by the O/E bit. Rev. 3.00 Mar 17, 2006 page 361 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 4—Parity Mode (O/E E): Selects either even or odd parity for use in parity addition and checking. The O/E bit setting is only valid when the PE bit is set to 1, enabling parity bit addition and checking, in asynchronous mode. The O/E bit setting is invalid in synchronous mode, when parity bit addition and checking is disabled in asynchronous mode, and when a multiprocessor format is used. Bit 4 O/E E Description 0 Even parity* 2 Odd parity* 1 1 (Initial value) Notes: 1. When even parity is set, parity bit addition is performed in transmission so that the total number of 1 bits in the transmit character plus the parity bit is even. In reception, a check is performed to see if the total number of 1 bits in the receive character plus the parity bit is even. 2. When odd parity is set, parity bit addition is performed in transmission so that the total number of 1 bits in the transmit character plus the parity bit is odd. In reception, a check is performed to see if the total number of 1 bits in the receive character plus the parity bit is odd. Bit 3—Stop Bit Length (STOP): Selects 1 or 2 bits as the stop bit length in asynchronous mode. The STOP bit setting is only valid in asynchronous mode. If synchronous mode is set the STOP bit setting is invalid since stop bits are not added. Bit 3 STOP Description 0 1 stop bit* 2 2 stop bits* 1 1 (Initial value) Notes: 1. In transmission, a single 1 bit (stop bit) is added to the end of a transmit character before it is sent. 2. In transmission, two 1 bits (stop bits) are added to the end of a transmit character before it is sent. In reception, only the first stop bit is checked, regardless of the STOP bit setting. If the second stop bit is 1, it is treated as a stop bit; if it is 0, it is treated as the start bit of the next transmit character. Rev. 3.00 Mar 17, 2006 page 362 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 2—Multiprocessor Mode (MP): Selects multiprocessor format. When multiprocessor format is selected, the PE bit and O/E bit parity settings are invalid. The MP bit setting is only valid in asynchronous mode; it is invalid in synchronous mode. For details of the multiprocessor communication function, see section 15.3.3, Multiprocessor Communication Function. Bit 2 MP Description 0 Multiprocessor function disabled 1 Multiprocessor format selected (Initial value) Bits 1 and 0—Clock Select 1 and 0 (CKS1, CKS0): These bits select the clock source for the baud rate generator. The clock source can be selected from φ, φ/4, φ/16, and φ/64, according to the setting of bits CKS1 and CKS0. For the relation between the clock source, the bit rate register setting, and the baud rate, see section 15.2.8, Bit Rate Register. Bit 1 Bit 0 CKS1 CKS0 Description 0 0 φ clock 1 φ/4 clock 0 φ/16 clock 1 φ/64 clock 1 15.2.6 (Initial value) Serial Control Register (SCR) Bit 7 6 5 4 3 2 1 0 TIE RIE TE RE MPIE TEIE CKE1 CKE0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W SCR is a register that performs enabling or disabling of SCI transfer operations, serial clock output in asynchronous mode, and interrupt requests, and selection of the serial clock source. SCR can be read or written to by the CPU at all times. Rev. 3.00 Mar 17, 2006 page 363 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) SCR is initialized to H'00 by a reset, and in standby mode, and module stop mode. Bit 7—Transmit Interrupt Enable (TIE): Enables or disables transmit-data-empty interrupt (TXI) request generation when serial transmit data is transferred from TDR to TSR and the TDRE flag in SSR is set to 1. Bit 7 TIE Description 0 Transmit-data-empty interrupt (TXI) request disabled* 1 Note: (Initial value) Transmit-data-empty interrupt (TXI) request enabled * TXI interrupt request cancellation can be performed by reading 1 from the TDRE flag, then clearing it to 0, or clearing the TIE bit to 0. Bit 6—Receive Interrupt Enable (RIE): Enables or disables receive-data-full interrupt (RXI) request and receive-error interrupt (ERI) request generation when serial receive data is transferred from RSR to RDR and the RDRF flag in SSR is set to 1. Bit 6 RIE Description 0 Receive-data-full interrupt (RXI) request and receive-error interrupt (ERI) request disabled* (Initial value) 1 Receive-data-full interrupt (RXI) request and receive-error interrupt (ERI) request enabled Note: * RXI and ERI interrupt request cancellation can be performed by reading 1 from the RDRF, FER, PER, or ORER flag, then clearing the flag to 0, or clearing the RIE bit to 0. Bit 5—Transmit Enable (TE): Enables or disables the start of serial transmission by the SCI. Bit 5 TE Description 0 Transmission disabled* 2 Transmission enabled* 1 1 (Initial value) Notes: 1. The TDRE flag in SSR is fixed at 1. 2. In this state, serial transmission is started when transmit data is written to TDR and the TDRE flag in SSR is cleared to 0. SMR setting must be performed to decide the transmission format before setting the TE bit to 1. Rev. 3.00 Mar 17, 2006 page 364 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 4—Receive Enable (RE): Enables or disables the start of serial reception by the SCI. Bit 4 RE Description 0 1 Reception disabled* 2 Reception enabled* 1 (Initial value) Notes: 1. Clearing the RE bit to 0 does not affect the RDRF, FER, PER, and ORER flags, which retain their states. 2. Serial reception is started in this state when a start bit is detected in asynchronous mode or serial clock input is detected in synchronous mode. SMR setting must be performed to decide the reception format before setting the RE bit to 1. Bit 3—Multiprocessor Interrupt Enable (MPIE): Enables or disables multiprocessor interrupts. The MPIE bit setting is only valid in asynchronous mode when receiving with the MP bit in SMR set to 1. The MPIE bit setting is invalid in synchronous mode or when the MP bit is cleared to 0. Bit 3 MPIE Description 0 Multiprocessor interrupts disabled (normal reception performed) (Initial value) [Clearing conditions] • When the MPIE bit is cleared to 0 • When data with MPB = 1 is received Multiprocessor interrupts enabled* 1 Receive interrupt (RXI) requests, receive-error interrupt (ERI) requests, and setting of the RDRF, FER, and ORER flags in SSR are disabled until data with the multiprocessor bit set to 1 is received. Note: * When receive data including MPB = 0 is received, receive data transfer from RSR to RDR, receive error detection, and setting of the RDRF, FER, and ORER flags in SSR, is not performed. When receive data with MPB = 1 is received, the MPB bit in SSR is set to 1, the MPIE bit is cleared to 0 automatically, and generation of RXI and ERI interrupts (when the TIE and RIE bits in SCR are set to 1) and FER and ORER flag setting is enabled. Bit 2—Transmit End Interrupt Enable (TEIE): Enables or disables transmit-end interrupt (TEI) request generation if there is no valid transmit data in TDR when the MSB is transmitted. Rev. 3.00 Mar 17, 2006 page 365 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 2 TEIE Description 0 Transmit-end interrupt (TEI) request disabled* Transmit-end interrupt (TEI) request enabled* 1 Note: (Initial value) TEI cancellation can be performed by reading 1 from the TDRE flag in SSR, then clearing it to 0 and clearing the TEND flag to 0, or clearing the TEIE bit to 0. * Bits 1 and 0—Clock Enable 1 and 0 (CKE1, CKE0): These bits are used to select the SCI clock source and enable or disable clock output from the SCK pin. The combination of the CKE1 and CKE0 bits determines whether the SCK pin functions as an I/O port, the serial clock output pin, or the serial clock input pin. The setting of the CKE0 bit, however, is only valid for internal clock operation (CKE1 = 0) in asynchronous mode. The CKE0 bit setting is invalid in synchronous mode, and in the case of external clock operation (CKE1 = 1). The setting of bits CKE1 and CKE0 must be carried out before the SCI’s operating mode is determined using SMR. For details of clock source selection, see table 15.9 in section 15.3, Operation. Bit 1 Bit 0 CKE1 CKE0 Description 0 0 Asynchronous mode Internal clock/SCK pin functions as I/O port* Synchronous mode Internal clock/SCK pin functions as serial clock 1 output* Asynchronous mode Internal clock/SCK pin functions as clock output* Synchronous mode Internal clock/SCK pin functions as serial clock output Asynchronous mode External clock/SCK pin functions as clock input* Synchronous mode External clock/SCK pin functions as serial clock input 3 External clock/SCK pin functions as clock input* 1 1 0 1 Asynchronous mode Synchronous mode External clock/SCK pin functions as serial clock input Notes: 1. Initial value 2. Outputs a clock of the same frequency as the bit rate. 3. Inputs a clock with a frequency 16 times the bit rate. Rev. 3.00 Mar 17, 2006 page 366 of 706 REJ09B0303-0300 1 2 3 Section 15 Serial Communication Interface (SCI) 15.2.7 Serial Status Register (SSR) Bit 7 6 5 4 3 2 1 0 TDRE RDRF ORER FER PER TEND MPB MPBT Initial value 1 0 0 0 0 1 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R R R/W Note: * Only 0 can be written, to clear the flag. SSR is an 8-bit register containing status flags that indicate the operating status of the SCI, and multiprocessor bits. SSR can be read or written to by the CPU at all times. However, 1 cannot be written to flags TDRE, RDRF, ORER, PER, and FER. Also note that in order to clear these flags they must be read as 1 beforehand. The TEND flag and MPB flag are read-only flags and cannot be modified. SSR is initialized to H'84 by a reset, and in standby mode, and module stop mode. Bit 7—Transmit Data Register Empty (TDRE): Indicates that data has been transferred from TDR to TSR and the next serial data can be written to TDR. Bit 7 TDRE Description 0 [Clearing condition] When 0 is written in TDRE after reading TDRE = 1 1 [Setting conditions] (Initial value) • When the TE bit in SCR is 0 • When data is transferred from TDR to TSR and data can be written to TDR Rev. 3.00 Mar 17, 2006 page 367 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 6—Receive Data Register Full (RDRF): Indicates that the received data is stored in RDR. Bit 6 RDRF Description 0 [Clearing condition] When 0 is written in RDRF after reading RDRF = 1 (Initial value) 1 [Setting condition] When serial reception ends normally and receive data is transferred from RSR to RDR Note: RDR and the RDRF flag are not affected and retain their previous values when an error is detected during reception or when the RE bit in SCR is cleared to 0. If reception of the next data is completed while the RDRF flag is still set to 1, an overrun error will occur and the receive data will be lost. Bit 5—Overrun Error (ORER): Indicates that an overrun error occurred during reception, causing abnormal termination. Bit 5 ORER Description 0 [Clearing condition] 1 (Initial value)* When 0 is written in ORER after reading ORER = 1 1 [Setting condition] When the next serial reception is completed while RDRF = 1* 2 Notes: 1. The ORER flag is not affected and retains its previous state when the RE bit in SCR is cleared to 0. 2. The receive data prior to the overrun error is retained in RDR, and the data received subsequently is lost. Also, subsequent serial reception cannot be continued while the ORER flag is set to 1. In synchronous mode, serial transmission cannot be continued, either. Rev. 3.00 Mar 17, 2006 page 368 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 4—Framing Error (FER): Indicates that a framing error occurred during reception in asynchronous mode, causing abnormal termination. Bit 4 FER Description 0 [Clearing condition] 1 (Initial value)* When 0 is written in FER after reading FER = 1 1 [Setting condition] When the SCI checks the stop bit at the end of the receive data when reception ends, 2 and the stop bit is 0* Notes: 1. The FER flag is not affected and retains its previous state when the RE bit in SCR is cleared to 0. 2. In 2-stop-bit mode, only the first stop bit is checked for a value of 0; the second stop bit is not checked. If a framing error occurs, the receive data is transferred to RDR but the RDRF flag is not set. Also, subsequent serial reception cannot be continued while the FER flag is set to 1. In synchronous mode, serial transmission cannot be continued, either. Bit 3—Parity Error (PER): Indicates that a parity error occurred during reception using parity addition in asynchronous mode, causing abnormal termination. Bit 3 PER Description 0 [Clearing condition] (Initial value)* 1 When 0 is written in PER after reading PER = 1 1 [Setting condition] When, in reception, the number of 1 bits in the receive data plus the parity bit does not 2 match the parity setting (even or odd) specified by the O/E bit in SMR* Notes: 1. The PER flag is not affected and retains its previous state when the RE bit in SCR is cleared to 0. 2. If a parity error occurs, the receive data is transferred to RDR but the RDRF flag is not set. Also, subsequent serial reception cannot be continued while the PER flag is set to 1. In synchronous mode, serial transmission cannot be continued, either. Rev. 3.00 Mar 17, 2006 page 369 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Bit 2—Transmit End (TEND): Indicates that there is no valid data in TDR when the last bit of the transmit character is sent, and transmission has been ended. The TEND flag is read-only and cannot be modified. Bit 2 TEND Description 0 [Clearing condition] When 0 is written in TDRE after reading TDRE = 1 1 [Setting conditions] (Initial value) • When the TE bit in SCR is 0 • When TDRE = 1 at transmission of the last bit of a 1-byte serial transmit character Bit 1—Multiprocessor Bit (MPB): When reception is performed using a multiprocessor format in asynchronous mode, MPB stores the multiprocessor bit in the receive data. MPB is a read-only bit, and cannot be modified. Bit 1 MPB Description 0 [Clearing condition] (Initial value)* When data with a 0 multiprocessor bit is received 1 [Setting condition] When data with a 1 multiprocessor bit is received Note: * Retains its previous state when the RE bit in SCR is cleared to 0 with multiprocessor format. Bit 0—Multiprocessor Bit Transfer (MPBT): When transmission is performed using a multiprocessor format in asynchronous mode, MPBT stores the multiprocessor bit to be added to the transmit data. The MPBT bit setting is invalid when a multiprocessor format is not used, when not transmitting, and in synchronous mode. Bit 0 MPBT Description 0 Data with a 0 multiprocessor bit is transmitted 1 Data with a 1 multiprocessor bit is transmitted Rev. 3.00 Mar 17, 2006 page 370 of 706 REJ09B0303-0300 (Initial value) Section 15 Serial Communication Interface (SCI) 15.2.8 Bit Rate Register (BRR) Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W BRR is an 8-bit register that sets the serial transfer bit rate in accordance with the baud rate generator operating clock selected by bits CKS1 and CKS0 in SMR. BRR can be read or written to by the CPU at all times. BRR is initialized to H'FF by a reset, and in standby mode, and module stop mode. As baud rate generator control is performed independently for each channel, different values can be set for each channel. Table 15.3 shows sample BRR settings in asynchronous mode, and table 15.4 shows sample BRR settings in synchronous mode. Rev. 3.00 Mar 17, 2006 page 371 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.3 BRR Settings for Various Bit Rates (Asynchronous Mode) Operating Frequency φ (MHz) φ = 2 MHz φ = 2.097152 MHz Bit Rate (bits/s) n N Error (%) n N Error (%) 110 1 141 0.03 1 148 150 1 103 0.16 1 300 0 207 0.16 600 0 103 1200 0 2400 4800 φ = 2.4576 MHz φ = 3 MHz N Error (%) N Error (%) –0.04 1 174 –0.26 1 212 0.03 108 0.21 1 127 0.00 1 155 0.16 0 217 0.21 0 255 0.00 1 77 0.16 0.16 0 108 0.21 0 127 0.00 0 155 0.16 51 0.16 0 54 –0.70 0 63 0.00 0 77 0.16 0 25 0.16 0 26 1.14 0 31 0.00 0 38 0.16 0 12 0.16 0 13 –2.48 0 15 0.00 0 19 –2.34 9600 — — — 0 6 –2.48 0 7 0.00 0 9 –2.34 19200 — — — — — — 0 3 0.00 0 4 –2.34 31250 0 1 0.00 — — — — — — 0 2 0.00 38400 — — — — — — 0 1 0.00 — — — n n Operating Frequency φ (MHz) φ = 3.6864 MHz φ = 4 MHz φ = 4.9152 MHz φ = 5 MHz Bit Rate (bits/s) n N Error (%) n N Error (%) n N Error (%) n N Error (%) 110 2 64 0.70 2 70 0.03 2 86 0.31 2 88 –0.25 150 1 191 0.00 1 207 0.16 1 255 0.00 2 64 0.16 300 1 95 0.00 1 103 0.16 1 127 0.00 1 129 0.16 600 0 191 0.00 0 207 0.16 0 255 0.00 1 64 0.16 1200 0 95 0.00 0 103 0.16 0 127 0.00 0 129 0.16 2400 0 47 0.00 0 51 0.16 0 63 0.00 0 64 0.16 4800 0 23 0.00 0 25 0.16 0 31 0.00 0 32 –1.36 9600 0 11 0.00 0 12 0.16 0 15 0.00 0 15 1.73 19200 0 5 0.00 — — — 0 7 0.00 0 7 1.73 31250 — — — 0 3 0.00 0 4 –1.70 0 4 0.00 38400 0 2 0.00 — — — 0 3 0.00 3 1.73 Rev. 3.00 Mar 17, 2006 page 372 of 706 REJ09B0303-0300 0 Section 15 Serial Communication Interface (SCI) Operating Frequency φ (MHz) φ = 6 MHz Bit Rate (bits/s) n N Error (%) 110 2 106 150 2 300 φ = 6.144 MHz φ = 7.3728 MHz φ = 8 MHz N Error (%) n N Error (%) –0.44 2 108 0.08 2 130 77 0.16 2 79 0.00 2 1 155 0.16 1 159 0.00 1 600 1 77 0.16 1 79 0.00 1 95 0.00 1 103 0.16 1200 0 155 0.16 0 159 0.00 0 191 0.00 0 207 0.16 2400 0 77 0.16 0 79 0.00 0 95 0.00 0 103 0.16 4800 0 38 0.16 0 39 0.00 0 47 0.00 0 51 0.16 9600 0 19 –2.34 0 19 0.00 0 23 0.00 0 25 0.16 19200 0 9 –2.34 0 9 0.00 0 11 0.00 0 12 0.16 31250 0 5 0.00 0 5 2.40 — — — 0 7 0.00 38400 0 4 –2.34 0 4 0.00 0 5 0.00 — — — n N Error (%) –0.07 2 141 0.03 95 0.00 2 103 0.16 191 0.00 1 207 0.16 n Operating Frequency φ (MHz) φ = 9.8304 MHz Bit Rate (bits/s) n N Error (%) 110 2 174 150 2 300 φ = 10 MHz N Error (%) –0.26 2 177 127 0.00 2 1 255 0.00 600 1 127 1200 0 255 2400 0 4800 φ = 12 MHz φ = 12.288 MHz N Error (%) n N Error (%) –0.25 2 212 0.03 2 217 0.08 129 0.16 2 155 0.16 2 159 0.00 2 64 0.16 2 77 0.16 2 79 0.00 0.00 1 129 0.16 1 155 0.16 1 159 0.00 0.00 1 64 0.16 1 77 0.16 1 79 0.00 127 0.00 0 129 0.16 0 155 0.16 0 159 0.00 0 63 0.00 0 64 0.16 0 77 0.16 0 79 0.00 9600 0 31 0.00 0 32 –1.36 0 38 0.16 0 39 0.00 19200 0 15 0.00 0 15 1.73 0 19 –2.34 0 19 0.00 31250 0 9 –1.70 0 9 0.00 0 11 0.00 11 2.40 38400 0 7 0.00 7 1.73 0 9 –2.34 0 9 0.00 n 0 n 0 Rev. 3.00 Mar 17, 2006 page 373 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Operating Frequency φ (MHz) φ = 14 MHz φ = 14.7456 MHz Bit Rate (bits/s) n N Error (%) 110 2 248 150 2 300 φ = 16 MHz φ = 17.2032 MHz N Error (%) n N Error (%) n N Error (%) –0.17 3 64 0.70 3 70 0.03 3 75 0.48 181 0.16 2 191 0.00 2 207 0.16 2 223 0.00 2 90 0.16 2 95 0.00 2 103 0.16 2 111 0.00 600 1 181 0.16 1 191 0.00 1 207 0.16 1 223 0.00 1200 1 90 0.16 1 95 0.00 1 103 0.16 1 111 0.00 2400 0 181 0.16 0 191 0.00 0 207 0.16 0 223 0.00 4800 0 90 0.16 0 95 0.00 0 103 0.16 0 111 0.00 9600 0 45 –0.93 0 47 0.00 0 51 0.16 0 55 0.00 19200 0 22 –0.93 0 23 0.00 0 25 0.16 0 27 0.00 31250 0 13 0.00 0 14 –1.70 0 15 0.00 0 16 1.20 38400 — — — 0 11 0.00 12 0.16 0 13 0.00 n 0 Operating Frequency φ (MHz) φ = 18 MHz Bit Rate (bits/s) n N Error (%) 110 3 79 150 2 300 φ = 19.6608 MHz φ = 20 MHz N Error (%) n N Error (%) –0.12 3 86 0.31 3 88 –0.25 233 0.16 2 255 0.00 3 64 0.16 2 116 0.16 2 127 0.00 2 129 0.16 600 1 233 0.16 1 255 0.00 2 64 0.16 1200 1 116 0.16 1 127 0.00 1 129 0.16 2400 0 233 0.16 0 255 0.00 1 64 0.16 4800 0 116 0.16 0 127 0.00 0 129 0.16 9600 0 58 –0.69 0 63 0.00 0 64 0.16 19200 0 28 1.02 0 31 0.00 0 32 –1.36 31250 0 17 0.00 0 19 –1.70 0 19 0.00 38400 0 14 –2.34 0 15 0.00 15 1.73 n Rev. 3.00 Mar 17, 2006 page 374 of 706 REJ09B0303-0300 0 Section 15 Serial Communication Interface (SCI) Table 15.4 BRR Settings for Various Bit Rates (Synchronous Mode) Operating Frequency φ (MHz) φ = 2 MHz Bit Rate φ = 4 MHz (bits/s) n N n N 110 3 70 — — 250 2 124 2 500 1 249 2 1k 1 124 2.5 k 0 5k φ = 8 MHz φ = 10 MHz φ = 16 MHz n N n N n N 249 3 124 — — 3 249 124 2 249 — — 3 1 249 2 124 — — 199 1 99 1 199 1 0 99 0 199 1 99 10 k 0 49 0 99 0 25 k 0 19 0 39 0 50 k 0 9 0 19 100 k 0 4 0 250 k 0 1 0 0* 500 k 1M φ = 20 MHz n N 124 — — 2 249 — — 249 2 99 2 124 1 124 1 199 1 249 199 0 249 1 99 1 124 79 0 99 0 159 0 199 0 39 0 49 0 79 0 99 9 0 19 0 24 0 39 0 49 0 3 0 7 0 9 0 15 0 19 0 1 0 3 0 4 0 7 0 9 0 0* 0 1 0 3 0 4 0 1 0 0* 2.5 M 0 5M 0* Legend: Blank: Cannot be set. —: Can be set, but there will be a degree of error. *: Continuous transfer is not possible. Note: As far as possible, the setting should be made so that the error is no more than 1%. Rev. 3.00 Mar 17, 2006 page 375 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) The BRR setting is found from the following equations. Asynchronous mode: N= φ 64 × 22n–1 ×B × 106 – 1 Synchronous mode: N= Where B: N: φ: n: φ × 106 – 1 8 × 22n–1 × B Bit rate (bits/s) BRR setting for baud rate generator (0 ≤ N ≤ 255) Operating frequency (MHz) Baud rate generator input clock (n = 0 to 3) (See the table below for the relation between n and the clock.) SMR Setting n Clock CKS1 CKS0 0 φ 0 0 1 φ/4 0 1 2 φ/16 1 0 3 φ/64 1 1 The bit rate error in asynchronous mode is found from the following equation: φ × 106 Error (%) = – 1 × 100 2n–1 (N + 1) × B × 64 × 2 Rev. 3.00 Mar 17, 2006 page 376 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.5 shows the maximum bit rate for each frequency in asynchronous mode. Tables 15.6 and 15.7 show the maximum bit rates with external clock input. Table 15.5 Maximum Bit Rate for Each Frequency (Asynchronous Mode) φ (MHz) Maximum Bit Rate (bits/s) n N 2 62500 0 0 2.097152 65536 0 0 2.4576 76800 0 0 3 93750 0 0 3.6864 115200 0 0 4 125000 0 0 4.9152 153600 0 0 5 156250 0 0 6 187500 0 0 6.144 192000 0 0 7.3728 230400 0 0 8 250000 0 0 9.8304 307200 0 0 10 312500 0 0 12 375000 0 0 12.288 384000 0 0 14 437500 0 0 14.7456 460800 0 0 16 500000 0 0 17.2032 537600 0 0 18 562500 0 0 19.6608 614400 0 0 20 625000 0 0 Rev. 3.00 Mar 17, 2006 page 377 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.6 Maximum Bit Rate with External Clock Input (Asynchronous Mode) φ (MHz) External Input Clock (MHz) Maximum Bit Rate (bits/s) 2 0.5000 31250 2.097152 0.5243 32768 2.4576 0.6144 38400 3 0.7500 46875 3.6864 0.9216 57600 4 1.0000 62500 4.9152 1.2288 76800 5 1.2500 78125 6 1.5000 93750 6.144 1.5360 96000 7.3728 1.8432 115200 8 2.0000 125000 9.8304 2.4576 153600 10 2.5000 156250 12 3.0000 187500 12.288 3.0720 192000 14 3.5000 218750 14.7456 3.6864 230400 16 4.0000 250000 17.2032 4.3008 268800 18 4.5000 281250 19.6608 4.9152 307200 20 5.0000 312500 Rev. 3.00 Mar 17, 2006 page 378 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.7 Maximum Bit Rate with External Clock Input (Synchronous Mode) φ (MHz) External Input Clock (MHz) Maximum Bit Rate (bits/s) 2 0.3333 333333.3 4 0.6667 666666.7 6 1.0000 1000000.0 8 1.3333 1333333.3 10 1.6667 1666666.7 12 2.0000 2000000.0 14 2.3333 2333333.3 16 2.6667 2666666.7 18 3.0000 3000000.0 20 3.3333 3333333.3 Rev. 3.00 Mar 17, 2006 page 379 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.2.9 Serial Interface Mode Register (SCMR) Bit 7 6 5 4 3 2 1 0 — — — — SDIR SINV — SMIF Initial value 1 1 1 1 0 0 1 0 Read/Write — — — — R/W R/W — R/W SCMR is an 8-bit readable/writable register used to select SCI functions. SCMR is initialized to H'F2 by a reset, and in standby mode, and module stop mode. Bits 7 to 4—Reserved: These bits cannot be modified and are always read as 1. Bit 3—Data Transfer Direction (SDIR): Selects the serial/parallel conversion format. Bit 3 SDIR Description 0 TDR contents are transmitted LSB-first (Initial value) Receive data is stored in RDR LSB-first 1 TDR contents are transmitted MSB-first Receive data is stored in RDR MSB-first Bit 2—Data Invert (SINV): Specifies inversion of the data logic level. The SINV bit does not affect the logic level of the parity bit(s): parity bit inversion requires inversion of the O/E bit in SMR. Bit 2 SINV Description 0 TDR contents are transmitted without modification Receive data is stored in RDR without modification 1 TDR contents are inverted before being transmitted Receive data is stored in RDR in inverted form Bit 1—Reserved: This bit cannot be modified and is always read as 1. Rev. 3.00 Mar 17, 2006 page 380 of 706 REJ09B0303-0300 (Initial value) Section 15 Serial Communication Interface (SCI) Bit 0—Serial Communication Interface Mode Select (SMIF): Reserved bit. 1 should not be written in this bit. Bit 0 SMIF Description 0 Normal SCI mode 1 Reserved mode (Initial value) 15.2.10 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR, comprising two 8-bit readable/writable registers, performs module stop mode control. When bits MSTP7 is set to 1, SCI0 operation, respectively, stops at the end of the bus cycle and a transition is made to module stop mode. For details, see section 21.5., Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. Bit 7—Module Stop (MSTP7): Specifies the SCI0 module stop mode. Bit 7 MSTP7 Description 0 SCI0 module stop mode is cleared 1 SCI0 module stop mode is set (Initial value) Rev. 3.00 Mar 17, 2006 page 381 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.3 Operation 15.3.1 Overview The SCI can carry out serial communication in two modes: asynchronous mode in which synchronization is achieved character by character, and synchronous mode in which synchronization is achieved with clock pulses. Selection of asynchronous or synchronous mode and the transmission format is made using SMR as shown in table 15.8. The SCI clock is determined by a combination of the C/A bit in SMR and the CKE1 and CKE0 bits in SCR, as shown in table 15.9. Asynchronous Mode • Data length: Choice of 7 or 8 bits • Choice of parity addition, multiprocessor bit addition, and addition of 1 or 2 stop bits (the combination of these parameters determines the transfer format and character length) • Detection of framing, parity, and overrun errors, and breaks, during reception • Choice of internal or external clock as SCI clock source When internal clock is selected: The SCI operates on the baud rate generator clock and a clock with the same frequency as the bit rate can be output When external clock is selected: A clock with a frequency of 16 times the bit rate must be input (the built-in baud rate generator is not used) Synchronous Mode • Transfer format: Fixed 8-bit data • Detection of overrun errors during reception • Choice of internal or external clock as SCI clock source When internal clock is selected: The SCI operates on the baud rate generator clock and a serial clock is output off-chip When external clock is selected: The built-in baud rate generator is not used, and the SCI operates on the input serial clock Rev. 3.00 Mar 17, 2006 page 382 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.8 SMR Settings and Serial Transfer Format Selection SMR Settings Bit 7 Bit 6 Bit 2 SCI Transfer Format Bit 5 C/A A CHR MP PE STOP Mode 0 0 0 0 0 Asynchronous mode 1 1 Data Length Multiprocessor Bit Parity Bit Stop Bit Length 8-bit data No No 1 bit Bit 3 2 bits 0 Yes 1 1 0 2 bits 0 7-bit data No 1 1 1 0 1 1 — — — 0 — 1 — 0 — 1 — — 1 bit 2 bits Yes 1 0 1 bit 1 bit 2 bits Asynchronous mode (multiprocessor format) 8-bit data Yes No 1 bit 2 bits 7-bit data 1 bit 2 bits Synchronous mode 8-bit data No None Table 15.9 SMR and SCR Settings and SCI Clock Source Selection SMR SCR Setting SCI Transfer Clock Bit 7 Bit 1 Bit 0 C/A A CKE1 CKE0 Mode 0 0 0 Asynchronous mode 1 1 0 Clock Source Internal 0 0 1 1 0 Synchronous mode SCI does not use SCK pin Outputs clock with same frequency as bit rate External Inputs clock with frequency of 16 times the bit rate Internal Outputs serial clock External Inputs serial clock 1 1 SCK Pin Function 1 Rev. 3.00 Mar 17, 2006 page 383 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.3.2 Operation in Asynchronous Mode In asynchronous mode, characters are sent or received, each preceded by a start bit indicating the start of communication and followed by one or two stop bits indicating the end of communication. Serial communication is thus carried out with synchronization established on a character-bycharacter basis. Inside the SCI, the transmitter and receiver are independent units, enabling full-duplex communication. Both the transmitter and the receiver also have a double-buffered structure, so that data can be read or written during transmission or reception, enabling continuous data transfer. Figure 15.2 shows the general format for asynchronous serial communication. In asynchronous serial communication, the transmission line is usually held in the mark state (high level). The SCI monitors the transmission line, and when it goes to the space state (low level), recognizes a start bit and starts serial communication. One serial communication character consists of a start bit (low level), followed by data (in LSBfirst order), a parity bit (high or low level), and finally one or two stop bits (high level). In asynchronous mode, the SCI performs synchronization at the falling edge of the start bit in reception. The SCI samples the data on the 8th pulse of a clock with a frequency of 16 times the length of one bit, so that the transfer data is latched at the center of each bit. Idle state (mark state) LSB 1 Serial data 0 D0 MSB D1 D2 D3 D4 D5 Start bit Transmit/receive data 1 bit 7 or 8 bits D6 D7 1 0/1 1 1 Parity Stop bit(s) bit 1 bit, or none 1 or 2 bits One unit of transfer data (character or frame) Figure 15.2 Data Format in Asynchronous Communication (Example with 8-Bit Data, Parity, Two Stop Bits) Rev. 3.00 Mar 17, 2006 page 384 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Data Transfer Format Table 15.10 shows the data transfer formats that can be used in asynchronous mode. Any of 12 transfer formats can be selected by settings in SMR. Table 15.10 Serial Transfer Formats (Asynchronous Mode) SMR Settings Serial Transfer Format and Frame Length CHR PE MP STOP 1 2 3 4 5 6 7 8 9 10 11 12 0 0 0 0 S 8-bit data STOP 0 0 0 1 S 8-bit data STOP STOP 0 1 0 0 S 8-bit data P STOP 0 1 0 1 S 8-bit data P STOP STOP 1 0 0 0 S 7-bit data STOP 1 0 0 1 S 7-bit data STOP STOP 1 1 0 0 S 7-bit data P STOP 1 1 0 1 S 7-bit data P STOP STOP 0 — 1 0 S 8-bit data MPB STOP 0 — 1 1 S 8-bit data MPB STOP STOP 1 — 1 0 S 7-bit data MPB STOP 1 — 1 1 S 7-bit data MPB STOP STOP Legend: S: Start bit STOP: Stop bit P: Parity bit MPB: Multiprocessor bit Rev. 3.00 Mar 17, 2006 page 385 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Clock Either an internal clock generated by the built-in baud rate generator or an external clock input at the SCK pin can be selected as the SCI’s serial clock, according to the setting of the C/A bit in SMR and the CKE1 and CKE0 bits in SCR. For details of SCI clock source selection, see table 15.9. When an external clock is input at the SCK pin, the clock frequency should be 16 times the bit rate used. When the SCI is operated on an internal clock, the clock can be output from the SCK pin. The frequency of the clock output in this case is equal to the bit rate, and the phase is such that the rising edge of the clock is at the center of each transmit data bit, as shown in figure 15.3. 0 D0 D1 D2 D3 D4 D5 D6 D7 0/1 1 1 1 frame Figure 15.3 Relation between Output Clock and Transfer Data Phase (Asynchronous Mode) Data Transfer Operations SCI Initialization (Asynchronous Mode): Before transmitting and receiving data, first clear the TE and RE bits in SCR to 0, then initialize the SCI as described below. When the operating mode, transfer format, etc., is changed, the TE and RE bits must be cleared to 0 before making the change using the following procedure. When the TE bit is cleared to 0, the TDRE flag is set to 1 and TSR is initialized. Note that clearing the RE bit to 0 does not change the contents of the RDRF, PER, FER, and ORER flags, or the contents of RDR. When an external clock is used the clock should not be stopped during operation, including initialization, since operation is uncertain. Rev. 3.00 Mar 17, 2006 page 386 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Figure 15.4 shows a sample SCI initialization flowchart. [1] Set the clock selection in SCR. Be sure to clear bits RIE, TIE, TEIE, and MPIE, and bits TE and RE, to 0. Start initialization Clear TE and RE bits in SCR to 0 Set CKE1 and CKE0 bits in SCR (TE, RE bits 0) [1] Set data transfer format in SMR and SCMR [2] Set value in BRR [3] Wait No 1-bit interval elapsed? Yes Set TE and RE bits in SCR to 1, and set RIE, TIE, TEIE, and MPIE bits When the clock is selected in asynchronous mode, it is output immediately after SCR settings are made. [2] Set the data transfer format in SMR and SCMR. [3] Write a value corresponding to the bit rate to BRR. This is not necessary if an external clock is used. [4] Wait at least one bit interval, then set the TE bit or RE bit in SCR to 1. Also set the RIE, TIE, TEIE, and MPIE bits. Setting the TE and RE bits enables the TxD and RxD pins to be used. [4] <Initialization completed> Figure 15.4 Sample SCI Initialization Flowchart Rev. 3.00 Mar 17, 2006 page 387 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Serial Data Transmission (Asynchronous Mode): Figure 15.5 shows a sample flowchart for serial transmission. The following procedure should be used for serial data transmission. [1] Initialization Start transmission Read TDRE flag in SSR [2] [2] SCI status check and transmit data write: Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR and clear the TDRE flag to 0. No TDRE = 1? Yes Write transmit data to TDR and clear TDRE flag in SSR to 0 No All data transmitted? Yes [3] No TEND = 1? Yes No [3] Serial transmission continuation procedure: To continue serial transmission, read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR, and then clear the TDRE flag to 0. [4] Break output at the end of serial transmission: To output a break in serial transmission, set DDR for the port corresponding to the TxD pin to 1, clear DR to 0, then clear the TE bit in SCR to 0. Read TEND flag in SSR Break output? [1] SCI initialization: The TxD pin is automatically designated as the transmit data output pin. After the TE bit is set to 1, one frame of 1s is output and transmission is enabled. [4] Yes Clear DR to 0 and set DDR to 1 Clear TE bit in SCR to 0 <End> Figure 15.5 Sample Serial Transmission Flowchart Rev. 3.00 Mar 17, 2006 page 388 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) In serial transmission, the SCI operates as described below. 1. The SCI monitors the TDRE flag in SSR, and if it is 0, recognizes that data has been written to TDR, and transfers the data from TDR to TSR. 2. After transferring data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts transmission. If the TIE bit is set to 1 at this time, a transmit data empty interrupt (TXI) is generated. The serial transmit data is sent from the TxD pin in the following order. a. Start bit: One 0-bit is output. b. Transmit data: 8-bit or 7-bit data is output in LSB-first order. c. Parity bit or multiprocessor bit: One parity bit (even or odd parity), or one multiprocessor bit is output. A format in which neither a parity bit nor a multiprocessor bit is output can also be selected. d. Stop bit(s): One or two 1-bits (stop bits) are output. e. Mark state: 1 is output continuously until the start bit that starts the next transmission is sent. 3. The SCI checks the TDRE flag at the timing for sending the stop bit. If the TDRE flag is cleared to 0, the data is transferred from TDR to TSR, the stop bit is sent, and then serial transmission of the next frame is started. If the TDRE flag is set to 1, the TEND flag in SSR is set to 1, the stop bit is sent, and then the mark state is entered in which 1 is output continuously. If the TEIE bit in SCR is set to 1 at this time, a TEI interrupt request is generated. Rev. 3.00 Mar 17, 2006 page 389 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Figure 15.6 shows an example of the operation for transmission in asynchronous mode. 1 Start bit 0 Data D0 D1 Parity Stop Start bit bit bit D7 0/1 1 0 Data D0 D1 Parity Stop bit bit D7 0/1 1 1 Idle state (mark state) TDRE TEND TXI interrupt Data written to TDR and TXI interrupt request generated TDRE flag cleared to 0 in request generated TXI interrupt handling routine TEI interrupt request generated 1 frame Figure 15.6 Example of Operation in Transmission in Asynchronous Mode (Example with 8-Bit Data, Parity, One Stop Bit) Rev. 3.00 Mar 17, 2006 page 390 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Serial Data Reception (Asynchronous Mode): Figure 15.7 shows a sample flowchart for serial reception. The following procedure should be used for serial data reception. Initialization [1] Start reception [1] SCI initialization: The RxD pin is automatically designated as the receive data input pin. [2] [3] Receive error handling and break detection: Read ORER, PER, and If a receive error occurs, read the [2] FER flags in SSR ORER, PER, and FER flags in SSR to identify the error. After performing the appropriate error Yes handling, ensure that the ORER, PER ∨ FER ∨ ORER= 1? PER, and FER flags are all [3] cleared to 0. Reception cannot No Error handling be resumed if any of these flags (Continued on next page) are set to 1. In the case of a framing error, a break can be detected by reading the value of [4] Read RDRF flag in SSR the input port corresponding to the RxD pin. No RDRF = 1? [4] SCI status check and receive data read : Read SSR and check that RDRF = 1, then read the receive data in RDR and clear the RDRF flag to 0. Transition of the RDRF flag from 0 to 1 can also be identified by an RXI interrupt. Yes Read receive data in RDR, and clear RDRF flag in SSR to 0 No All data received? Yes Clear RE bit in SCR to 0 [5] [5] Serial reception continuation procedure: To continue serial reception, before the stop bit for the current frame is received, read the RDRF flag, read RDR, and clear the RDRF flag to 0. <End> Figure 15.7 Sample Serial Reception Data Flowchart Rev. 3.00 Mar 17, 2006 page 391 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) [3] Error handling No ORER = 1? Yes Overrun error handling No FER = 1? Yes Yes Break? No Framing error handling Clear RE bit in SCR to 0 No PER = 1? Yes Parity error handling Clear ORER, PER, and FER flags in SSR to 0 <End> Figure 15.7 Sample Serial Reception Data Flowchart (cont) Rev. 3.00 Mar 17, 2006 page 392 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) In serial reception, the SCI operates as described below. 1. The SCI monitors the transmission line, and if a 0 stop bit is detected, performs internal synchronization and starts reception. 2. The received data is stored in RSR in LSB-to-MSB order. 3. The parity bit and stop bit are received. After receiving these bits, the SCI carries out the following checks. a. Parity check: The SCI checks whether the number of 1 bits in the receive data agrees with the parity (even or odd) set in the O/E bit in SMR. b. Stop bit check: The SCI checks whether the stop bit is 1. If there are two stop bits, only the first is checked. c. Status check: The SCI checks whether the RDRF flag is 0, indicating that the receive data can be transferred from RSR to RDR. If all the above checks are passed, the RDRF flag is set to 1, and the receive data is stored in RDR. If a receive error* is detected in the error check, the operation is as shown in table 15.11. Note: * Subsequent receive operations cannot be performed when a receive error has occurred. Also note that the RDRF flag is not set to 1 in reception, and so the error flags must be cleared to 0. 4. If the RIE bit in SCR is set to 1 when the RDRF flag changes to 1, a receive-data-full interrupt (RXI) request is generated. Also, if the RIE bit in SCR is set to 1 when the ORER, PER, or FER flag changes to 1, a receive-error interrupt (ERI) request is generated. Rev. 3.00 Mar 17, 2006 page 393 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Table 15.11 Receive Errors and Conditions for Occurrence Receive Error Abbreviation Occurrence Condition Data Transfer Overrun error ORER When the next data reception is completed while the RDRF flag in SSR is set to 1 Receive data is not transferred from RSR to RDR Framing error FER When the stop bit is 0 Receive data is transferred from RSR to RDR Parity error PER When the received data differs from the parity (even or odd) set in SMR Receive data is transferred from RSR to RDR Figure 15.8 shows an example of the operation for reception in asynchronous mode. 1 Start bit 0 Data D0 D1 Parity Stop Start bit bit bit D7 0/1 1 0 Data D0 D1 Parity Stop bit bit D7 0/1 1 1 Idle state (mark state) RDRF FER RXI interrupt request generated RDR data read and RDRF flag cleared to 0 in RXI interrupt handling routine ERI interrupt request generated by framing error 1 frame Figure 15.8 Example of SCI Operation in Reception (Example with 8-Bit Data, Parity, One Stop Bit) Rev. 3.00 Mar 17, 2006 page 394 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.3.3 Multiprocessor Communication Function The multiprocessor communication function performs serial communication using a multiprocessor format, in which a multiprocessor bit is added to the transfer data, in asynchronous mode. Use of this function enables data transfer to be performed among a number of processors sharing transmission lines. When multiprocessor communication is carried out, each receiving station is addressed by a unique ID code. The serial communication cycle consists of two component cycles: an ID transmission cycle which specifies the receiving station, and a data transmission cycle. The multiprocessor bit is used to differentiate between the ID transmission cycle and the data transmission cycle. The transmitting station first sends the ID of the receiving station with which it wants to perform serial communication as data with a 1 multiprocessor bit added. It then sends transmit data as data with a 0 multiprocessor bit added. The receiving station skips the data until data with a 1 multiprocessor bit is sent. When data with a 1 multiprocessor bit is received, the receiving station compares that data with its own ID. The station whose ID matches then receives the data sent next. Stations whose ID does not match continue to skip the data until data with a 1 multiprocessor bit is again received. In this way, data communication is carried out among a number of processors. Figure 15.9 shows an example of inter-processor communication using a multiprocessor format. Data Transfer Format There are four data transfer formats. When a multiprocessor format is specified, the parity bit specification is invalid. For details, see table 15.10. Rev. 3.00 Mar 17, 2006 page 395 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Clock See the section on asynchronous mode. Transmitting station Serial communication line Receiving station A Receiving station B Receiving station C Receiving station D (ID = 01) (ID = 02) (ID = 03) (ID = 04) Serial data H'01 H'AA (MPB = 1) ID transmission cycle: receiving station specification (MPB = 0) Data transmission cycle: data transmission to receiving station specified by ID Legend: MPB: Multiprocessor bit Figure 15.9 Example of Inter-Processor Communication Using Multiprocessor Format (Transmission of Data H'AA to Receiving Station A) Data Transfer Operations Multiprocessor Serial Data Transmission: Figure 15.10 shows a sample flowchart for multiprocessor serial data transmission. The following procedure should be used for multiprocessor serial data transmission. Rev. 3.00 Mar 17, 2006 page 396 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) [1] [1] SCI initialization: Initialization Start transmission Read TDRE flag in SSR [2] [2] SCI status check and transmit data write: Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR. Set the MPBT bit in SSR to 0 or 1. Finally, clear the TDRE flag to 0. No TDRE = 1? Yes Write transmit data to TDR and set MPBT bit in SSR Clear TDRE flag to 0 No All data transmitted? Yes The TxD pin is automatically designated as the transmit data output pin. After the TE bit is set to 1, one frame of 1s is output and transmission is enabled. [3] Serial transmission continuation procedure: To continue serial transmission, be sure to read 1 from the TDRE flag to confirm that writing is [3] possible, then write data to TDR, and then clear the TDRE flag to 0. [4] Break output at the end of serial transmission: To output a break in serial transmission, set the port DDR to 1, clear DR to 0, then clear the TE bit in SCR to 0. Read TEND flag in SSR No TEND = 1? Yes No Break output? [4] Yes Clear DR to 0 and set DDR to 1 Clear TE bit in SCR to 0 <End> Figure 15.10 Sample Multiprocessor Serial Transmission Flowchart Rev. 3.00 Mar 17, 2006 page 397 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) In serial transmission, the SCI operates as described below. 1. The SCI monitors the TDRE flag in SSR, and if it is 0, recognizes that data has been written to TDR, and transfers the data from TDR to TSR. 2. After transferring data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts transmission. If the TIE bit is set to 1 at this time, a transmit-data-empty interrupt (TXI) is generated. The serial transmit data is sent from the TxD pin in the following order. a. Start bit: One 0-bit is output. b. Transmit data: 8-bit or 7-bit data is output in LSB-first order. c. Multiprocessor bit One multiprocessor bit (MPBT value) is output. d. Stop bit(s): One or two 1-bits (stop bits) are output. e. Mark state: 1 is output continuously until the start bit that starts the next transmission is sent. 3. The SCI checks the TDRE flag at the timing for sending the stop bit. If the TDRE flag is cleared to 0, data is transferred from TDR to TSR, the stop bit is sent, and then serial transmission of the next frame is started. If the TDRE flag is set to 1, the TEND flag in SSR is set to 1, the stop bit is sent, and then the mark state is entered in which 1 is output continuously. If the TEIE bit in SCR is set to 1 at this time, a transmit-end interrupt (TEI) request is generated. Rev. 3.00 Mar 17, 2006 page 398 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Figure 15.11 shows an example of SCI operation for transmission using a multiprocessor format. 1 Start bit 0 Multiprocessor Stop bit bit Data D0 D1 D7 0/1 1 Start bit 0 Multiproces- Stop 1 sor bit bit Data D0 D1 D7 0/1 1 Idle state (mark state) TDRE TEND TXI interrupt request generated Data written to TDR and TDRE flag cleared to 0 in TXI interrupt handling routine TXI interrupt request generated TEI interrupt request generated 1 frame Figure 15.11 Example of SCI Operation in Transmission (Example with 8-Bit Data, Multiprocessor Bit, One Stop Bit) Multiprocessor Serial Data Reception: Figure 15.12 shows a sample flowchart for multiprocessor serial reception. The following procedure should be used for multiprocessor serial data reception. Rev. 3.00 Mar 17, 2006 page 399 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Initialization [1] [1] SCI initialization: The RxD pin is automatically designated as the receive data input pin. [2] [2] ID reception cycle: Set the MPIE bit in SCR to 1. Start reception Read MPIE bit in SCR Read ORER and FER flags in SSR FER ∨ ORER = 1? [3] SCI status check, ID reception and comparison: Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR and compare it with this station’s ID. If the data is not this station’s ID, set the MPIE bit to 1 again, and clear the RDRF flag to 0. If the data is this station’s ID, clear the RDRF flag to 0. Yes No Read RDRF flag in SSR [3] No RDRF = 1? Yes [4] SCI status check and data reception: Read SSR and check that the RDRF flag is set to 1, then read the data in RDR. Read receive data in RDR No This station's ID? Yes [5] Receive error handling and break detection: If a receive error occurs, read the ORER and FER flags in SSR to identify the error. After performing the appropriate error handling, ensure that the ORER and FER flags are both cleared to 0. Reception cannot be resumed if either of these flags is set to 1. In the case of a framing error, a break can be detected by reading the RxD pin value. Read ORER and FER flags in SSR FER ∨ ORER = 1? Yes No Read RDRF flag in SSR [4] No RDRF = 1? Yes Read receive data in RDR No All data received? [5] Error handling Yes Clear RE bit in SCR to 0 (Continued on next page) <End> Figure 15.12 Sample Multiprocessor Serial Reception Flowchart Rev. 3.00 Mar 17, 2006 page 400 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) [5] Error handling No ORER = 1? Yes Overrun error handling No FER = 1? Yes Yes Break? No Framing error handling Clear RE bit in SCR to 0 Clear ORER, PER, and FER flags in SSR to 0 <End> Figure 15.12 Sample Multiprocessor Serial Reception Flowchart (cont) Rev. 3.00 Mar 17, 2006 page 401 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Figure 15.13 shows an example of SCI operation for multiprocessor format reception. 1 Start bit 0 Data (ID1) MPB D0 D1 D7 1 Stop bit Start bit 1 0 Data (Data1) MPB D0 D1 D7 0 Stop bit 1 1 Idle state (mark state) MPIE RDRF RDR value ID1 RXI interrupt request (multiprocessor interrupt) generated MPIE = 0 RDR data read and RDRF flag cleared to 0 in RXI interrupt handling routine If not this station’s ID, RXI interrupt request is MPIE bit is set to 1 not generated, and RDR again retains its state (a) Data does not match station’s ID 1 Start bit 0 Data (ID2) MPB D0 D1 D7 1 Stop bit Start bit 1 0 Data (Data2) MPB D0 D1 D7 0 Stop bit 1 1 Idle state (mark state) MPIE RDRF RDR value ID2 ID1 MPIE = 0 RXI interrupt request (multiprocessor interrupt) generated RDR data read and RDRF flag cleared to 0 in RXI interrupt handling routine Matches this station’s ID, so reception continues, and data is received in RXI interrupt handling routine (b) Data matches station’s ID Figure 15.13 Example of SCI Operation in Reception (Example with 8-Bit Data, Multiprocessor Bit, One Stop Bit) Rev. 3.00 Mar 17, 2006 page 402 of 706 REJ09B0303-0300 Data2 MPIE bit set to 1 again Section 15 Serial Communication Interface (SCI) 15.3.4 Operation in Synchronous Mode In synchronous mode, data is transmitted or received in synchronization with clock pulses, making it suitable for high-speed serial communication. Inside the SCI, the transmitter and receiver are independent units, enabling full-duplex communication by use of a common clock. Both the transmitter and the receiver also have a double-buffered structure, so that data can be read or written during transmission or reception, enabling continuous data transfer. Figure 15.14 shows the general format for synchronous serial communication. One unit of transfer data (character or frame) * * Serial clock LSB Serial data Bit 0 MSB Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Don’t care Don’t care Note: * High except in continuous transfer Figure 15.14 Data Format in Synchronous Communication In synchronous serial communication, data on the transmission line is output from one falling edge of the serial clock to the next. Data is guaranteed valid at the rising edge of the serial clock. In synchronous serial communication, one character consists of data output starting with the LSB and ending with the MSB. After the MSB is output, the transmission line holds the MSB state. In synchronous mode, the SCI receives data in synchronization with the rising edge of the serial clock. Data Transfer Format A fixed 8-bit data format is used. No parity or multiprocessor bits are added. Rev. 3.00 Mar 17, 2006 page 403 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Clock Either an internal clock generated by the built-in baud rate generator or an external serial clock input at the SCK pin can be selected, according to the setting of the C/A bit in SMR and the CKE1 and CKE0 bits in SCR. For details on SCI clock source selection, see table 15.9. When the SCI is operated on an internal clock, the serial clock is output from the SCK pin. Eight serial clock pulses are output in the transfer of one character, and when no transfer is performed the clock is fixed high. When only receive operations are performed, however, the serial clock is output until an overrun error occurs or the RE bit is cleared to 0. To perform receive operations in units of one character, select an external clock as the clock source. Data Transfer Operations SCI Initialization (Synchronous Mode): Before transmitting and receiving data, first clear the TE and RE bits in SCR to 0, then initialize the SCI as described below. When the operating mode, transfer format, etc., is changed, the TE and RE bits must be cleared to 0 before making the change using the following procedure. When the TE bit is cleared to 0, the TDRE flag is set to 1 and TSR is initialized. Note that clearing the RE bit to 0 does not change the settings of the RDRF, PER, FER, and ORER flags, or the contents of RDR. Figure 15.15 shows a sample SCI initialization flowchart. Rev. 3.00 Mar 17, 2006 page 404 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) [1] Set the clock selection in SCR. Be sure to clear bits RIE, TIE, TEIE, and MPIE, TE and RE, to 0. Start initialization Clear TE and RE bits in SCR to 0 [2] Set the data transfer format in SMR and SCMR. Set CKE1 and CKE0 bits in SCR (TE, RE bits 0) [1] [3] Write a value corresponding to the bit rate to BRR. This is not necessary if an external clock is used. Set data transfer format in SMR and SCMR [2] Set value in BRR [3] [4] Wait at least one bit interval, then set the TE bit or RE bit in SCR to 1. Also set the RIE, TIE, TEIE, and MPIE bits. Setting the TE and RE bits enables the TxD and RxD pins to be used. Wait No 1-bit interval elapsed? Yes Set TE and RE bits in SCR to 1, and set RIE, TIE, TEIE, and MPIE bits [4] <Transfer start> Note: In simultaneous transmitting and receiving, the TE and RE bits should both be cleared to 0 or set to 1 simultaneously. Figure 15.15 Sample SCI Initialization Flowchart Rev. 3.00 Mar 17, 2006 page 405 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Serial Data Transmission (Synchronous Mode): Figure 15.16 shows a sample flowchart for serial transmission. The following procedure should be used for serial data transmission. [1] Initialization Start transmission Read TDRE flag in SSR [2] No TDRE = 1? Yes Write transmit data to TDR and clear TDRE flag in SSR to 0 No All data transmitted? [3] [1] SCI initialization: The TxD pin is automatically designated as the transmit data output pin. [2] SCI status check and transmit data write: Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR and clear the TDRE flag to 0. [3] Serial transmission continuation procedure: To continue serial transmission, be sure to read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR, and then clear the TDRE flag to 0. Yes Read TEND flag in SSR No TEND = 1? Yes Clear TE bit in SCR to 0 <End> Figure 15.16 Sample Serial Transmission Flowchart Rev. 3.00 Mar 17, 2006 page 406 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) In serial transmission, the SCI operates as described below. 1. The SCI monitors the TDRE flag in SSR, and if it is 0, recognizes that data has been written to TDR, and transfers the data from TDR to TSR. 2. After transferring data from TDR to TSR, the SCI sets the TDRE flag to 1 and starts transmission. If the TIE bit in SCR is set to 1 at this time, a transmit-data-empty interrupt (TXI) is generated. When clock output mode has been set, the SCI outputs 8 serial clock pulses. When use of an external clock has been specified, data is output synchronized with the input clock. The serial transmit data is sent from the TxD pin starting with the LSB (bit 0) and ending with the MSB (bit 7). 3. The SCI checks the TDRE flag at the timing for sending the MSB (bit 7). If the TDRE flag is cleared to 0, data is transferred from TDR to TSR, and serial transmission of the next frame is started. If the TDRE flag is set to 1, the TEND flag in SSR is set to 1, the MSB (bit 7) is sent, and the TxD pin maintains its state. If the TEIE bit in SCR is set to 1 at this time, a transmit-end interrupt (TEI) request is generated. 4. After completion of serial transmission, the SCK pin is held in a constant state. Figure 15.17 shows an example of SCI operation in transmission. Rev. 3.00 Mar 17, 2006 page 407 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Transfer direction Serial clock Serial data Bit 0 Bit 1 Bit 7 Bit 0 Bit 1 Bit 6 Bit 7 TDRE TEND TXI interrupt request generated Data written to TDR TXI interrupt and TDRE flag request generated cleared to 0 in TXI interrupt handling routine TEI interrupt request generated 1 frame Figure 15.17 Example of SCI Operation in Transmission Serial Data Reception (Synchronous Mode): Figure 15.18 shows a sample flowchart for serial reception. The following procedure should be used for serial data reception. When changing the operating mode from asynchronous to synchronous, be sure to check that the ORER, PER, and FER flags are all cleared to 0. The RDRF flag will not be set if the FER or PER flag is set to 1, and neither transmit nor receive operations will be possible. Rev. 3.00 Mar 17, 2006 page 408 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) [1] Initialization Start reception [2] Read ORER flag in SSR Yes [3] ORER = 1? No Error handling (Continued below) Read RDRF flag in SSR [4] No RDRF = 1? Yes Read receive data in RDR, and clear RDRF flag in SSR to 0 No All data received? Yes [5] [1] SCI initialization: The RxD pin is automatically designated as the receive data input pin. [2] [3] Receive error handling: If a receive error occurs, read the ORER flag in SSR , and after performing the appropriate error handling, clear the ORER flag to 0. Transfer cannot be resumed if the ORER flag is set to 1. [4] SCI status check and receive data read: Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR and clear the RDRF flag to 0. Transition of the RDRF flag from 0 to 1 can also be identified by an RXI interrupt. [5] Serial reception continuation procedure: To continue serial reception, before the MSB (bit 7) of the current frame is received, finish reading the RDRF flag, reading RDR, and clearing the RDRF flag to 0. Clear RE bit in SCR to 0 <End> [3] Error handling Overrun error handling Clear ORER flag in SSR to 0 <End> Figure 15.18 Sample Serial Reception Flowchart Rev. 3.00 Mar 17, 2006 page 409 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) In serial reception, the SCI operates as described below. 1. The SCI performs internal initialization in synchronization with serial clock input or output. 2. The received data is stored in RSR in LSB-to-MSB order. After reception, the SCI checks whether the RDRF flag is 0 and the receive data can be transferred from RSR to RDR. If this check is passed, the RDRF flag is set to 1, and the receive data is stored in RDR. If a receive error is detected in the error check, the operation is as shown in table 15.11. Neither transmit nor receive operations can be performed subsequently when a receive error has been found in the error check. 3. If the RIE bit in SCR is set to 1 when the RDRF flag changes to 1, a receive-data-full interrupt (RXI) request is generated. Also, if the RIE bit in SCR is set to 1 when the ORER flag changes to 1, a receive-error interrupt (ERI) request is generated. Figure 15.19 shows an example of SCI operation in reception. Serial clock Serial data Bit 7 Bit 0 Bit 7 Bit 0 Bit 1 Bit 6 Bit 7 RDRF ORER RXI interrupt request generated RDR data read and RDRF flag cleared to 0 in RXI interrupt handling routine RXI interrupt request generated ERI interrupt request generated by overrun error 1 frame Figure 15.19 Example of SCI Operation in Reception Simultaneous Serial Data Transmission and Reception (Synchronous Mode): Figure 15.20 shows a sample flowchart for simultaneous serial transmit and receive operations. The following procedure should be used for simultaneous serial data transmit and receive operations. Rev. 3.00 Mar 17, 2006 page 410 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Initialization [1] SCI initialization: [1] The TxD pin is designated as the transmit data output pin, and the RxD pin is designated as the receive data input pin, enabling simultaneous transmit and receive operations. Start transmission/reception Read TDRE flag in SSR [2] [2] SCI status check and transmit data write: Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR and clear the TDRE flag to 0. Transition of the TDRE flag from 0 to 1 can also be identified by a TXI interrupt. No TDRE = 1? Yes Write transmit data to TDR and clear TDRE flag in SSR to 0 [3] Receive error handling: Read ORER flag in SSR ORER = 1? No Read RDRF flag in SSR Yes [3] Error handling [4] No RDRF = 1? Yes No Yes Clear TE and RE bits in SCR to 0 [4] SCI status check and receive data read: Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR and clear the RDRF flag to 0. Transition of the RDRF flag from 0 to 1 can also be identified by an RXI interrupt. [5] Serial transmission/reception Read receive data in RDR, and clear RDRF flag in SSR to 0 All data received? If a receive error occurs, read the ORER flag in SSR , and after performing the appropriate error handling, clear the ORER flag to 0. Transmission/reception cannot be resumed if the ORER flag is set to 1. [5] continuation procedure: To continue serial transmission/ reception, before the MSB (bit 7) of the current frame is received, finish reading the RDRF flag, reading RDR, and clearing the RDRF flag to 0. Also, before the MSB (bit 7) of the current frame is transmitted, read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR and clear the TDRE flag to 0. <End> Note: When switching from transmit or receive operation to simultaneous transmit and receive operations, first clear the TE bit and RE bit to 0, then set both these bits to 1 simultaneously. Figure 15.20 Sample Flowchart of Simultaneous Serial Transmit and Receive Operations Rev. 3.00 Mar 17, 2006 page 411 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.4 SCI Interrupts The SCI has four interrupt sources: the transmit-end interrupt (TEI) request, receive-error interrupt (ERI) request, receive-data-full interrupt (RXI) request, and transmit-data-empty interrupt (TXI) request. Table 15.12 shows the interrupt sources and their relative priorities. Individual interrupt sources can be enabled or disabled with the TIE, RIE, and TEIE bits in SCR. Each kind of interrupt request is sent to the interrupt controller independently. Table 15.12 SCI Interrupt Sources Interrupt Source Description Priority ERI Receive error (ORER, FER, or PER) High RXI Receive data register full (RDRF) TXI Transmit data register empty (TDRE) TEI Transmit end (TEND) Low The TEI interrupt is requested when the TEND flag is set to 1 while the TEIE bit is set to 1. The TEND flag is cleared at the same time as the TDRE flag. Consequently, if a TEI interrupt and a TXI interrupt are requested simultaneously, the TXI interrupt will have priority for acceptance, and the TDRE flag and TEND flag may be cleared. Note that the TEI interrupt will not be accepted in this case. Rev. 3.00 Mar 17, 2006 page 412 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) 15.5 Usage Notes The following points should be noted when using the SCI. Relation between Writes to TDR and the TDRE Flag: The TDRE flag in SSR is a status flag that indicates that transmit data has been transferred from TDR to TSR. When the SCI transfers data from TDR to TSR, the TDRE flag is set to 1. Data can be written to TDR regardless of the state of the TDRE flag. However, if new data is written to TDR when the TDRE flag is cleared to 0, the data stored in TDR will be lost since it has not yet been transferred to TSR. It is therefore essential to check that the TDRE flag is set to 1 before writing transmit data to TDR. Operation when Multiple Receive Errors Occur Simultaneously: If a number of receive errors occur at the same time, the state of the status flags in SSR is as shown in table 15.13. If there is an overrun error, data is not transferred from RSR to RDR, and the receive data is lost. Table 15.13 State of SSR Status Flags and Transfer of Receive Data SSR Status Flags RDRF ORER FER PER Receive Data Transfer RSR to RDR Receive Errors 1 1 0 0 X Overrun error 0 0 1 0 O Framing error 0 0 0 1 O Parity error 1 1 1 0 X Overrun error + framing error 1 1 0 1 X Overrun error + parity error 0 0 1 1 O Framing error + parity error 1 1 1 1 X Overrun error + framing error + parity error Legend: O: Receive data is transferred from RSR to RDR. X: Receive data is not transferred from RSR to RDR. Break Detection and Processing: When a framing error (FER) is detected, a break can be detected by reading the RxD pin value directly. In a break, the input from the RxD pin becomes all 0s, and so the FER flag is set, and the parity error flag (PER) may also be set. Note that, since the SCI continues the receive operation after receiving a break, even if the FER flag is cleared to 0, it will be set to 1 again. Rev. 3.00 Mar 17, 2006 page 413 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Sending a Break: The TxD pin has a dual function as an I/O port whose direction (input or output) is determined by DR and DDR. This feature can be used to send a break. Between serial transmission initialization and setting of the TE bit to 1, the mark state is replaced by the value of DR (the pin does not function as the TxD pin until the TE bit is set to 1). Consequently, DDR and DR for the port corresponding to the TxD pin should first be set to 1. To send a break during serial transmission, first clear DR to 0, then clear the TE bit to 0. When the TE bit is cleared to 0, the transmitter is initialized regardless of the current transmission state, the TxD pin becomes an I/O port, and 0 is output from the TxD pin. Receive Error Flags and Transmit Operations (Synchronous Mode Only): Transmission cannot be started when a receive error flag (ORER, PER, or FER) is set to 1, even if the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 before starting transmission. Note also that receive error flags cannot be cleared to 0 even if the RE bit is cleared to 0. Receive Data Sampling Timing and Reception Margin in Asynchronous Mode: In asynchronous mode, the SCI operates on a base clock with a frequency of 16 times the transfer rate. In reception, the SCI samples the falling edge of the start bit using the base clock, and performs internal synchronization. Receive data is latched internally at the rising edge of the 8th pulse of the base clock. This is illustrated in figure 15.21. 16 clocks 8 clocks 0 7 15 0 7 15 0 Internal base clock Receive data (RxD) Start bit D0 Synchronization sampling timing Data sampling timing Figure 15.21 Receive Data Sampling Timing in Asynchronous Mode Rev. 3.00 Mar 17, 2006 page 414 of 706 REJ09B0303-0300 D1 Section 15 Serial Communication Interface (SCI) Thus the receive margin in asynchronous mode is given by equation (1) below. M = 0.5 – Where M: N: D: L: F: 1 D – 0.5 (1 + F) × 100% – (L – 0.5)F – 2N N .......... (1) Receive margin (%) Ratio of bit rate to clock (N = 16) Clock duty (D = 0 to 1.0) Frame length (L = 9 to 12) Absolute value of clock rate deviation Assuming values of F = 0 and D = 0.5 in equation (1), a receive margin of 46.875% is given by equation (2) below. When D = 0.5 and F = 0, M = 0.5 – 1 × 100% 2 × 16 = 46.875% .......... (2) However, this is only a theoretical value, and a margin of 20% to 30% should be allowed in system design. Rev. 3.00 Mar 17, 2006 page 415 of 706 REJ09B0303-0300 Section 15 Serial Communication Interface (SCI) Rev. 3.00 Mar 17, 2006 page 416 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 2 Section 16 I C Bus Interface (IIC) 16.1 Overview 2 2 The H8/3577 Group and H8/3567 Group have an on-chip two-channel I C bus interface. The I C 2 bus interface conforms to and provides a subset of the Philips I C bus (inter-IC bus) interface 2 functions. The register configuration that controls the I C bus differs partly from the Philips configuration, however. 2 Each I C bus interface channel uses only one data line (SDA) and one clock line (SCL) to transfer data, saving board and connector space. 16.1.1 Features • Selection of addressing format or non-addressing format I C bus format: addressing format with acknowledge bit, for master/slave operation 2 Serial format: non-addressing format without acknowledge bit, for master operation only • Conforms to Philips I C bus interface (I C bus format) 2 2 • Two ways of setting slave address (I C bus format) 2 • Start and stop conditions generated automatically in master mode (I C bus format) 2 • Selection of acknowledge output levels when receiving (I C bus format) 2 • Automatic loading of acknowledge bit when transmitting (I C bus format) 2 • Wait function in master mode (I C bus format) 2 A wait can be inserted by driving the SCL pin low after data transfer, excluding acknowledgement. The wait can be cleared by clearing the interrupt flag. • Wait function in slave mode (I C bus format) 2 A wait request can be generated by driving the SCL pin low after data transfer, excluding acknowledgement. The wait request is cleared when the next transfer becomes possible. • Three interrupt sources Data transfer end (including transmission mode transition with I C bus format and address reception after loss of master arbitration) 2 Address match: when any slave address matches or the general call address is received in 2 slave receive mode (I C bus format) Stop condition detection • Selection of 16 internal clocks (in master mode) Rev. 3.00 Mar 17, 2006 page 417 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • Direct bus drive (with SCL and SDA pins) Two pins—P52/SCL0 and P47/SDA0—(normally NMOS push-pull outputs) function as NMOS open-drain outputs when the bus drive function is selected. Two pins—P24/SCL1 and P23/SDA1 in the H8/3577 Group, and P17/SCL1 and P16/SDA1 in the H8/3567 Group—(normally CMOS pins) function as NMOS-only outputs when the bus drive function is selected. • Automatic switching from formatless mode to I C bus format (channel 0 only) 2 Formatless operation (no start/stop conditions, non-addressing mode) in slave mode Operation using a common data pin (SDA) and independent clock pins (VSYNCI, SCL) Automatic switching from formatless mode to I C bus format on the fall of the SCL pin 2 16.1.2 Block Diagram 2 Figure 16.1 shows a block diagram of the I C bus interface. Figure 16.2 shows an example of I/O pin connections to external circuits. Channel 0 I/O pins and channel 1 I/O pins differ in structure, and have different specifications for permissible applied voltages. For details, see section 22, Electrical Characteristics. Rev. 3.00 Mar 17, 2006 page 418 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Formatless dedicated clock (channel 0 only) φ PS ICCR SCL Clock control Noise canceler Bus state decision circuit SDA ICSR Arbitration decision circuit ICDRT Output data control circuit ICDRS Internal data bus ICMR ICDRR Noise canceler Address comparator SAR, SARX Interrupt generator Legend: ICCR: I2C bus control register ICMR: I2C bus mode register ICSR: I2C bus status register ICDR: I2C bus data register SAR: Slave address register SARX: Slave address register X PS: Prescaler Interrupt request 2 Figure 16.1 Block Diagram of I C Bus Interface Rev. 3.00 Mar 17, 2006 page 419 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Vcc Vcc SCL SCL SDA SDA SCL in SDA in SCL SDA SDA out (Master) SCL in H8/3577 Group or H8/3567 Group chip SCL out SCL out SDA in SDA in SDA out SDA out SCL SDA SCL out SCL in (Slave 1) (Slave 2) 2 Figure 16.2 I C Bus Interface Connections (Example: H8/3577 Group or H8/3567 Group Chip as Master) 16.1.3 Input/Output Pins 2 Table 16.1 summarizes the input/output pins used by the I C bus interface. 2 Table 16.1 I C Bus Interface Pins Channel Name Abbreviation* I/O Function 0 Serial clock SCL0 I/O IIC0 serial clock input/output Serial data SDA0 I/O IIC0 serial data input/output Formatless serial clock VSYNCI Input IIC0 formatless serial clock input Serial clock SCL1 I/O IIC1 serial clock input/output Serial data SDA1 I/O IIC1 serial data input/output 1 Note: * In the text, the channel subscript is omitted, and only SCL and SDA are used. Rev. 3.00 Mar 17, 2006 page 420 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.1.4 Register Configuration 2 Table 16.2 summarizes the registers of the I C bus interface. Table 16.2 Register Configuration Channel Name Abbreviation R/W Initial Value Address 2 ICCR0 R/W H'01 H'FFD8 2 ICSR0 R/W H'00 H'FFD9 2 ICDR0 R/W — I C bus mode register ICMR0 R/W H'00 H'FFDE* H'FFDF* Slave address register SAR0 R/W H'00 Second slave address register SARX0 R/W H'01 H'FFDF* H'FFDE* 2 ICCR1 R/W H'01 H'FF88 2 ICSR1 R/W H'00 H'FF89 2 ICDR1 R/W — 2 I C bus mode register ICMR1 R/W H'00 H'FF8E* H'FF8F* Slave address register SAR1 R/W H'00 Second slave address register SARX1 R/W H'01 H'FF8F* H'FF8E* Serial timer control register STCR R/W H'00 H'FFC3 DDC switch register DDCSWR R/W H'0F H'FEE6 Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF I C bus control register 0 I C bus status register I C bus data register 2 1 I C bus control register I C bus status register I C bus data register Common Note: * H'FF87 2 The register that can be written or read depends on the ICE bit in the I C bus control 2 register. The slave address register can be accessed when ICE = 0, and the I C bus mode register can be accessed when ICE = 1. 2 The I C bus interface registers are assigned to the same addresses as other registers. Register selection is performed by means of the IICE bit in the serial timer control register (STCR). Rev. 3.00 Mar 17, 2006 page 421 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.2 Register Descriptions 16.2.1 I C Bus Data Register (ICDR) 2 Bit 7 6 5 4 3 2 1 0 ICDR7 ICDR6 ICDR5 ICDR4 ICDR3 ICDR2 ICDR1 ICDR0 Initial value — — — — — — — — Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 • ICDRR Bit ICDRR7 ICDRR6 ICDRR5 ICDRR4 ICDRR3 ICDRR2 ICDRR1 ICDRR0 Initial value — — — — — — — — Read/Write R R R R R R R R 7 6 5 4 3 2 1 0 • ICDRS Bit ICDRS7 ICDRS6 ICDRS5 ICDRS4 ICDRS3 ICDRS2 ICDRS1 ICDRS0 Initial value — — — — — — — — Read/Write — — — — — — — — 7 6 5 4 3 2 1 0 ICDRT4 ICDRT3 ICDRT2 ICDRT1 ICDRT0 • ICDRT Bit ICDRT7 ICDRT6 ICDRT5 Initial value — — — — — — — — Read/Write W W W W W W W W • TDRE, RDRF (internal flags) Bit — — TDRE RDRF Initial value 0 0 Read/Write — — Rev. 3.00 Mar 17, 2006 page 422 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) ICDR is an 8-bit readable/writable register that is used as a transmit data register when transmitting and a receive data register when receiving. ICDR is divided internally into a shift register (ICDRS), receive buffer (ICDRR), and transmit buffer (ICDRT). ICDRS cannot be read or written by the CPU, ICDRR is read-only, and ICDRT is write-only. Data transfers among the three registers are performed automatically in coordination with changes in the bus state, and affect the status of internal flags such as TDRE and RDRF. If IIC is in transmit mode and the next data is in ICDRT (the TDRE flag is 0) following transmission of one frame of data using ICDRS, data is transferred automatically from ICDRT to ICDRS. If the IIC is in receive mode and none of the previous data remains in ICDRR (the RDRF flag is 0), after one frame of data has been received normally in ICDRS, the data is transferred automatically from ICDRS to ICDRR. If the number of bits in a frame, excluding the acknowledge bit, is less than 8, transmit data and receive data are stored differently. Transmit data should be written justified toward the MSB side when MLS = 0, and toward the LSB side when MLS = 1. Receive data bits read from the LSB side should be treated as valid when MLS = 0, and bits read from the MSB side when MLS = 1. ICDR is assigned to the same address as SARX, and can be written and read only when the ICE bit is set to 1 in ICCR. The value of ICDR is undefined after a reset. The TDRE and RDRF flags are set and cleared under the conditions shown below. Setting the TDRE and RDRF flags affects the status of the interrupt flags. Rev. 3.00 Mar 17, 2006 page 423 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) TDRE Description 0 The next transmit data is in ICDR (ICDRT), or transmission cannot be started (Initial value) [Clearing conditions] • When transmit data is written in ICDR (ICDRT) in transmit mode (TRS = 1) • When a stop condition is detected in the bus line state after a stop condition is 2 issued with the I C bus format or serial format selected • When a stop condition is detected with the I C bus format selected • In receive mode (TRS = 0) 2 (A 0 write to TRS during transfer is valid after reception of a frame containing an acknowledge bit) 1 The next transmit data can be written in ICDR (ICDRT) [Setting conditions] • In transmit mode (TRS = 1), when a start condition is detected in the bus line state 2 after a start condition is issued in master mode with the I C bus format or serial format selected • When using formatless mode in transmit mode (TRS = 1) • When data is transferred from ICDRT to ICDRS (Data transfer from ICDRT to ICDRS when TRS = 1 and TDRE = 0, and ICDRS is empty) • When a switch is made from receive mode (TRS = 0) to transmit mode (TRS = 1 ) after detection of a start condition RDRF Description 0 The data in ICDR (ICDRR) is invalid (Initial value) [Clearing condition] When ICDR (ICDRR) receive data is read in receive mode 1 The ICDR (ICDRR) receive data can be read [Setting condition] When data is transferred from ICDRS to ICDRR (Data transfer from ICDRS to ICDRR in case of normal termination with TRS = 0 and RDRF = 0) Rev. 3.00 Mar 17, 2006 page 424 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.2.2 Slave Address Register (SAR) Bit 7 6 5 4 3 2 1 0 SVA6 SVA5 SVA4 SVA3 SVA2 SVA1 SVA0 FS Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W SAR is an 8-bit readable/writable register that stores the slave address and selects the communication format. When the chip is in slave mode (and the addressing format is selected), if the upper 7 bits of SAR match the upper 7 bits of the first frame received after a start condition, the chip operates as the slave device specified by the master device. SAR is assigned to the same address as ICMR, and can be written and read only when the ICE bit is cleared to 0 in ICCR. SAR is initialized to H'00 by a reset and in hardware standby mode. Bits 7 to 1—Slave Address (SVA6 to SVA0): Set a unique address in bits SVA6 to SVA0, 2 differing from the addresses of other slave devices connected to the I C bus. Bit 0—Format Select (FS): Used together with the FSX bit in SARX and the SW bit in DDCSWR to select the communication format. • I C bus format: addressing format with acknowledge bit 2 • Synchronous serial format: non-addressing format without acknowledge bit, for master mode only • Formatless mode (channel 0 only): non-addressing format with or without acknowledge bit, slave mode only, start/stop conditions not detected The FS bit also specifies whether or not SAR slave address recognition is performed in slave mode. Rev. 3.00 Mar 17, 2006 page 425 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) DDCSWR Bit 6 SAR Bit 0 SARX Bit 0 SW FS FSX Operating Mode 0 0 0 I C bus format 2 • 1 1 0 1 0 1 SAR slave address recognized • SARX slave address ignored 2 I C bus format • SAR slave address ignored • SARX slave address recognized Synchronous serial format Formatless mode (start/stop conditions not detected) 1 • Acknowledge bit used 0 Formatless mode* (start/stop conditions not detected) • * SAR and SARX slave addresses ignored 0 1 Note: (Initial value) • • 1 SAR and SARX slave addresses recognized 2 I C bus format No acknowledge bit 2 Do not set this mode when automatic switching to the I C bus format is performed by means of the DDCSWR setting. Rev. 3.00 Mar 17, 2006 page 426 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.2.3 Second Slave Address Register (SARX) Bit 7 6 5 4 3 2 1 0 SVAX6 SVAX5 SVAX4 SVAX3 SVAX2 SVAX1 SVAX0 FSX Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W SARX is an 8-bit readable/writable register that stores the second slave address and selects the communication format. When the chip is in slave mode (and the addressing format is selected), if the upper 7 bits of SARX match the upper 7 bits of the first frame received after a start condition, the chip operates as the slave device specified by the master device. SARX is assigned to the same address as ICDR, and can be written and read only when the ICE bit is cleared to 0 in ICCR. SARX is initialized to H'01 by a reset and in hardware standby mode. Bits 7 to 1—Second Slave Address (SVAX6 to SVAX0): Set a unique address in bits SVAX6 to 2 SVAX0, differing from the addresses of other slave devices connected to the I C bus. Bit 0—Format Select X (FSX): Used together with the FS bit in SAR and the SW bit in DDCSWR to select the communication format. • I C bus format: addressing format with acknowledge bit 2 • Synchronous serial format: non-addressing format without acknowledge bit, for master mode only • Formatless mode: non-addressing format with or without acknowledge bit, slave mode only, start/stop conditions not detected The FSX bit also specifies whether or not SARX slave address recognition is performed in slave mode. For details, see the description of the FS bit in SAR. Rev. 3.00 Mar 17, 2006 page 427 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.2.4 2 I C Bus Mode Register (ICMR) Bit 7 6 5 4 3 2 1 0 MLS WAIT CKS2 CKS1 CKS0 BC2 BC1 BC0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W ICMR is an 8-bit readable/writable register that selects whether the MSB or LSB is transferred first, performs master mode wait control, and selects the master mode transfer clock frequency and the transfer bit count. ICMR is assigned to the same address as SAR. ICMR can be written and read only when the ICE bit is set to 1 in ICCR. ICMR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—MSB-First/LSB-First Select (MLS): Selects whether data is transferred MSB-first or LSB-first. If the number of bits in a frame, excluding the acknowledge bit, is less than 8, transmit data and receive data are stored differently. Transmit data should be written justified toward the MSB side when MLS = 0, and toward the LSB side when MLS = 1. Receive data bits read from the LSB side should be treated as valid when MLS = 0, and bits read from the MSB side when MLS = 1. 2 Do not set this bit to 1 when the I C bus format is used. Bit 7 MLS Description 0 MSB-first 1 LSB-first (Initial value) Bit 6—Wait Insertion Bit (WAIT): Selects whether to insert a wait between the transfer of data 2 and the acknowledge bit, in master mode with the I C bus format. When WAIT is set to 1, after the fall of the clock for the final data bit, the IRIC flag is set to 1 in ICCR, and a wait state begins (with SCL at the low level). When the IRIC flag is cleared to 0 in ICCR, the wait ends and the acknowledge bit is transferred. If WAIT is cleared to 0, data and acknowledge bits are transferred consecutively with no wait inserted. The IRIC flag in ICCR is set to 1 on completion of the acknowledge bit transfer, regardless of the WAIT setting. The setting of this bit is invalid in slave mode. Rev. 3.00 Mar 17, 2006 page 428 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 6 WAIT Description 0 Data and acknowledge bits transferred consecutively 1 Wait inserted between data and acknowledge bits (Initial value) Bits 5 to 3—Serial Clock Select (CKS2 to CKS0): These bits, together with the IICX1 (channel 1) or IICX0 (channel 0) bit in the STCR register, select the serial clock frequency in master mode. They should be set according to the required transfer rate. STCR Bit 5 or 6 Bit 5 Bit 4 Bit 3 Transfer Rate IICX CKS2 CKS1 CKS0 Clock 0 0 0 1 1 0 1 1 0 0 1 1 0 1 Note: * φ= 5 MHz φ= 8 MHz φ= 10 MHz φ= 16 MHz φ= 20 MHz 0 φ/28 179 kHz 286 kHz 357 kHz 571 kHz* 1 φ/40 125 kHz 200 kHz 250 kHz 400 kHz 714 kHz* 500 kHz* 0 φ/48 104 kHz 167 kHz 208 kHz 333 kHz 417 kHz* 1 φ/64 78.1 kHz 125 kHz 156 kHz 250 kHz 313 kHz 0 φ/80 62.5 kHz 100 kHz 125 kHz 200 kHz 250 kHz 1 φ/100 50.0 kHz 80.0 kHz 100 kHz 160 kHz 200 kHz 0 φ/112 44.6 kHz 71.4 kHz 89.3 kHz 143 kHz 179 kHz 1 φ/128 39.1 kHz 62.5 kHz 78.1 kHz 125 kHz 156 kHz 0 φ/56 89.3 kHz 143 kHz 179 kHz 286 kHz 357 kHz 1 φ/80 62.5 kHz 100 kHz 125 kHz 200 kHz 250 kHz 0 φ/96 52.1 kHz 83.3 kHz 104 kHz 167 kHz 208 kHz 1 φ/128 39.1 kHz 62.5 kHz 78.1 kHz 125 kHz 156 kHz 0 φ/160 31.3 kHz 50.0 kHz 62.5 kHz 100 kHz 125 kHz 1 φ/200 25.0 kHz 40.0 kHz 50.0 kHz 80.0 kHz 100 kHz 0 φ/224 22.3 kHz 35.7 kHz 44.6 kHz 71.4 kHz 89.3 kHz 1 φ/256 19.5 kHz 31.3 kHz 39.1 kHz 62.5 kHz 78.1 kHz 2 Outside the I C bus interface specification range (normal mode: max. 100 kHz; highspeed mode: max. 400 kHz). Bits 2 to 0—Bit Counter (BC2 to BC0): Bits BC2 to BC0 specify the number of bits to be 2 transferred next. With the I C bus format (when the FS bit in SAR or the FSX bit in SARX is 0), the data is transferred with one addition acknowledge bit. Bits BC2 to BC0 settings should be made during an interval between transfer frames. If bits BC2 to BC0 are set to a value other than 000, the setting should be made while the SCL line is low. Rev. 3.00 Mar 17, 2006 page 429 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) The bit counter is initialized to 000 by a reset and when a start condition is detected. The value returns to 000 at the end of a data transfer, including the acknowledge bit. Bit 2 Bit 1 Bit 0 BC2 BC1 BC0 Synchronous Serial Format I C Bus Format 0 0 0 8 9 1 1 2 0 2 3 1 3 4 0 4 5 1 5 6 0 6 7 1 7 8 1 1 0 1 Bits/Frame 2 (Initial value) 2 16.2.5 I C Bus Control Register (ICCR) Bit 7 6 5 4 3 2 1 0 ICE IEIC MST TRS ACKE BBSY IRIC SCP Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/(W)* W Note: * Only 0 can be written, to clear the flag. 2 ICCR is an 8-bit readable/writable register that enables or disables the I C bus interface, enables or disables interrupts, selects master or slave mode and transmission or reception, enables or disables 2 acknowledgement, confirms the I C bus interface bus status, issues start/stop conditions, and performs interrupt flag confirmation. ICCR is initialized to H'01 by a reset and in hardware standby mode. 2 2 Bit 7—I C Bus Interface Enable (ICE): Selects whether or not the I C bus interface is to be used. When ICE is set to 1, port pins function as SCL and SDA input/output pins and transfer operations are enabled. When ICE bit is cleared to 0, the module stops the functions and clears the internal state. The SAR and SARX registers can be accessed when ICE is 0. The ICMR and ICDR registers can be accessed when ICE is 1. Rev. 3.00 Mar 17, 2006 page 430 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 7 ICE Description 0 I C bus interface module disabled, with SCL and SDA signal pins set to port function (Initial value) 2 Initialization of IIC module internal state SAR and SARX can be accessed 2 1 I C bus interface module enabled for transfer operations (pins SCL and SCA are driving the bus) ICMR and ICDR can be accessed 2 2 Bit 6—I C Bus Interface Interrupt Enable (IEIC): Enables or disables interrupts from the I C bus interface to the CPU. Bit 6 IEIC Description 0 Interrupts disabled 1 Interrupts enabled (Initial value) Bit 5—Master/Slave Select (MST) Bit 4—Transmit/Receive Select (TRS) 2 MST selects whether the I C bus interface operates in master mode or slave mode. 2 TRS selects whether the I C bus interface operates in transmit mode or receive mode. 2 In master mode with the I C bus format, when arbitration is lost, MST and TRS are both reset by hardware, causing a transition to slave receive mode. In slave receive mode with the addressing format (FS = 0 or FSX = 0), hardware automatically selects transmit or receive mode according to the R/W bit in the first frame after a start condition. Modification of the TRS bit during transfer is deferred until transfer of the frame containing the acknowledge bit is completed, and the changeover is made after completion of the transfer. MST and TRS select the operating mode as follows. Rev. 3.00 Mar 17, 2006 page 431 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 5 Bit 4 MST TRS Operating Mode 0 0 Slave receive mode 1 Slave transmit mode 0 Master receive mode 1 Master transmit mode 1 (Initial value) Bit 5 MST Description 0 Slave mode (Initial value) [Clearing conditions] 1. When 0 is written by software 2 2. When bus arbitration is lost after transmission is started in I C bus format master mode 1 Master mode [Setting conditions] 1. When 1 is written by software (in cases other than clearing condition 2) 2. When 1 is written in MST after reading MST = 0 (in case of clearing condition 2) Bit 4 TRS Description 0 Receive mode (Initial value) [Clearing conditions] 1. When 0 is written by software (in cases other than setting condition 3) 2. When 0 is written in TRS after reading TRS = 1 (in case of clearing condition 3) 2 3. When bus arbitration is lost after transmission is started in I C bus format master mode 4. When the SW bit in DDCSWR changes from 1 to 0 1 Transmit mode [Setting conditions] 1. When 1 is written by software (in cases other than clearing conditions 3 and 4) 2. When 1 is written in TRS after reading TRS = 0 (in case of clearing conditions 3 and 4) 2 3. When a 1 is received as the R/W bit of the first frame in I C bus format slave mode Rev. 3.00 Mar 17, 2006 page 432 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 3—Acknowledge Bit Judgement Selection (ACKE): Specifies whether the value of the 2 acknowledge bit returned from the receiving device when using the I C bus format is to be ignored and continuous transfer is performed, or transfer is to be aborted and error handling, etc., performed if the acknowledge bit is 1. When the ACKE bit is 0, the value of the received acknowledge bit is not indicated by the ACKB bit, which is always 0. Bit 3 ACKE Description 0 The value of the acknowledge bit is ignored, and continuous transfer is performed (Initial value) 1 If the acknowledge bit is 1, continuous transfer is interrupted 2 Bit 2—Bus Busy (BBSY): The BBSY flag can be read to check whether the I C bus (SCL, SDA) is busy or free. In master mode, this bit is also used to issue start and stop conditions. A high-to-low transition of SDA while SCL is high is recognized as a start condition, setting BBSY to 1. A low-to-high transition of SDA while SCL is high is recognized as a stop condition, clearing BBSY to 0. To issue a start condition, write 1 in BBSY and 0 in SCP. A retransmit start condition is issued in the same way. To issue a stop condition, use a MOV instruction to write 0 in BBSY and 0 in SCP. 2 It is not possible to write to BBSY in slave mode; the I C bus interface must be set to master transmit mode before issuing a start condition. MST and TRS should both be set to 1 before writing 1 in BBSY and 0 in SCP. Bit 2 BBSY Description 0 Bus is free (Initial value) [Clearing condition] When a stop condition is detected 1 Bus is busy [Setting condition] When a start condition is detected 2 2 Bit 1—I C Bus Interface Interrupt Request Flag (IRIC): Indicates that the I C bus interface has issued an interrupt request to the CPU. IRIC is set to 1 at the end of a data transfer, when a slave address or general call address is detected in slave receive mode, when bus arbitration is lost in master transmit mode, and when a stop condition is detected. IRIC is set at different times depending on the FS bit in SAR and the WAIT bit in ICMR. See section 16.3.6, IRIC Setting Rev. 3.00 Mar 17, 2006 page 433 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Timing and SCL Control. The conditions under which IRIC is set also differ depending on the setting of the ACKE bit in ICCR. IRIC is cleared by reading IRIC after it has been set to 1, then writing 0 in IRIC. Bit 1 IRIC Description 0 Waiting for transfer, or transfer in progress [Clearing condition] When 0 is written in IRIC after reading IRIC = 1 1 Interrupt requested [Setting conditions] • I2C bus format master mode When a start condition is detected in the bus line state after a start condition is issued (when the TDRE flag is set to 1 because of first frame transmission) When a wait is inserted between the data and acknowledge bit when WAIT = 1 At the end of data transfer (at the rise of the 9th transmit/receive clock pulse, and, when a wait is inserted, at the fall of the 8th transmit/receive clock pulse) When a slave address is received after bus arbitration is lost (when the AL flag is set to 1) When 1 is received as the acknowledge bit when the ACKE bit is 1 (when the ACKB bit is set to 1) • I2C bus format slave mode When the slave address (SVA, SVAX) matches (when the AAS and AASX flags are set to 1) and at the end of data transfer up to the subsequent retransmission start condition or stop condition detection (when the TDRE or RDRF flag is set to 1) When the general call address is detected (when the FS = 0 and the ADZ flag is set to 1) and at the end of data transfer up to the subsequent retransmission start condition or stop condition detection (when the TDRE or RDRF flag is set to 1) When 1 is received as the acknowledge bit when the ACKE bit is 1 (when the ACKB bit is set to 1) When a stop condition is detected (when the STOP or ESTP flag is set to 1) • Synchronous serial format, and formatless mode At the end of data transfer (when the TDRE or RDRF flag is set to 1) When a start condition is detected with serial format selected When the SW bit is set to 1 in DDCSWR Besides the above, when a condition that sets the TDRE or RDRF internal flag to 1 occurs Rev. 3.00 Mar 17, 2006 page 434 of 706 REJ09B0303-0300 (Initial value) 2 Section 16 I C Bus Interface (IIC) 2 When, with the I C bus format selected, IRIC is set to 1 and an interrupt is generated, other flags must be checked in order to identify the source that set IRIC to 1. Although each source has a corresponding flag, caution is needed at the end of a transfer. When the TDRE or RDRF internal flag is set, the readable IRTR flag may or may not be set. The IRTR flag is not set at the end of a data transfer up to detection of a retransmission start condition 2 or stop condition after a slave address (SVA) or general call address match in I C bus format slave mode. Even when the IRIC flag and IRTR flag are set, the TDRE or RDRF internal flag may not be set. Table 16.3 shows the relationship between the flags and the transfer states. Table 16.3 Flags and Transfer States MST TRS BBSY ESTP STOP IRTR AASX AL AAS ADZ ACKB State 1/0 1/0 0 0 0 0 0 0 0 0 0 Idle state (flag clearing required) 1 1 0 0 0 0 0 0 0 0 0 Start condition issuance 1 1 1 0 0 1 0 0 0 0 0 Start condition established 1 1/0 1 0 0 0 0 0 0 0 0/1 Master mode wait 1 1/0 1 0 0 1 0 0 0 0 0/1 Master mode transmit/receive end 0 0 1 0 0 0 1/0 1 1/0 1/0 0 Arbitration lost 0 0 1 0 0 0 0 0 1 0 0 SAR match by first frame in slave mode 0 0 1 0 0 0 0 0 1 1 0 General call address match 0 0 1 0 0 0 1 0 0 0 0 SARX match 0 1/0 1 0 0 0 0 0 0 0 0/1 Slave mode transmit/receive end (except after SARX match) 0 1/0 1 0 0 1 1 0 0 0 0 0 1 1 0 0 0 1 0 0 0 1 Slave mode transmit/receive end (after SARX match) 0 1/0 0 1/0 1/0 0 0 0 0 0 0/1 Stop condition detected Rev. 3.00 Mar 17, 2006 page 435 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 0—Start Condition/Stop Condition Prohibit (SCP): Controls the issuing of start and stop conditions in master mode. To issue a start condition, write 1 in BBSY and 0 in SCP. A retransmit start condition is issued in the same way. To issue a stop condition, write 0 in BBSY and 0 in SCP. This bit is always read as 1. If 1 is written, the data is not stored. Bit 0 SCP Description 0 Writing 0 issues a start or stop condition, in combination with the BBSY flag 1 Reading always returns a value of 1 (Initial value) Writing is ignored 2 16.2.6 I C Bus Status Register (ICSR) Bit 7 6 5 4 3 2 1 0 ESTP STOP IRTR AASX AL AAS ADZ ACKB Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/W Note: * Only 0 can be written, to clear the flags. ICSR is an 8-bit readable/writable register that performs flag confirmation and acknowledge confirmation and control. ICSR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—Error Stop Condition Detection Flag (ESTP): Indicates that a stop condition has been 2 detected during frame transfer in I C bus format slave mode. Rev. 3.00 Mar 17, 2006 page 436 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 7 ESTP Description 0 No error stop condition (Initial value) [Clearing conditions] 1 • When 0 is written in ESTP after reading ESTP = 1 • When the IRIC flag is cleared to 0 • In I C bus format slave mode 2 Error stop condition detected [Setting condition] When a stop condition is detected during frame transfer • In other modes No meaning Bit 6—Normal Stop Condition Detection Flag (STOP): Indicates that a stop condition has been 2 detected after completion of frame transfer in I C bus format slave mode. Bit 6 STOP Description 0 No normal stop condition (Initial value) [Clearing conditions] 1 • When 0 is written in STOP after reading STOP = 1 • When the IRIC flag is cleared to 0 • In I C bus format slave mode 2 Normal stop condition detected [Setting condition] When a stop condition is detected after completion of frame transfer • In other modes No meaning 2 Bit 5—I C Bus Interface Continuous Transmission/Reception Interrupt Request Flag 2 (IRTR): Indicates that the I C bus interface has issued an interrupt request to the CPU, and the source is completion of reception/transmission of one frame in continuous transmission/reception for which DTC activation is possible. As the H8/3577 Group and H8/3567 Group do not have an on-chip DTC, the IRTR flag is used by the CPU to determine the source that set IRIC. When the IRTR flag is set to 1, the IRIC flag is also set to 1 at the same time. Rev. 3.00 Mar 17, 2006 page 437 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) IRTR flag setting is performed when the TDRE or RDRF flag is set to 1. IRTR is cleared by reading IRTR after it has been set to 1, then writing 0 in IRTR. IRTR is also cleared automatically when the IRIC flag is cleared to 0. Bit 5 IRTR Description 0 Waiting for transfer, or transfer in progress (Initial value) [Clearing conditions] 1 • When 0 is written in IRTR after reading IRTR = 1 • When the IRIC flag is cleared to 0 Continuous transfer state [Setting conditions] • 2 In I C bus interface slave mode When the TDRE or RDRF flag is set to 1 when AASX = 1 • In other modes When the TDRE or RDRF flag is set to 1 2 Bit 4—Second Slave Address Recognition Flag (AASX): In I C bus format slave receive mode, this flag is set to 1 if the first frame following a start condition matches bits SVAX6 to SVAX0 in SARX. AASX is cleared by reading AASX after it has been set to 1, then writing 0 in AASX. AASX is also cleared automatically when a start condition is detected. Bit 4 AASX Description 0 Second slave address not recognized (Initial value) [Clearing conditions] 1 • When 0 is written in AASX after reading AASX = 1 • When a start condition is detected • In master mode Second slave address recognized [Setting condition] When the second slave address is detected in slave receive mode while FSX = 0 Rev. 3.00 Mar 17, 2006 page 438 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 3—Arbitration Lost (AL): This flag indicates that arbitration was lost in master mode. The 2 I C bus interface monitors the SDA. When two or more master devices attempt to seize the bus at 2 nearly the same time, if the I C bus interface detects data differing from the data it sent, it sets AL to 1 to indicate that the bus has been taken by another master. AL is cleared by reading AL after it has been set to 1, then writing 0 in AL. In addition, AL is reset automatically by write access to ICDR in transmit mode, or read access to ICDR in receive mode. Bit 3 AL Description 0 Bus arbitration won (Initial value) [Clearing conditions] 1 • When ICDR data is written (transmit mode) or read (receive mode) • When 0 is written in AL after reading AL = 1 Arbitration lost [Setting conditions] • If the internal SDA and SDA pin disagree at the rise of SCL in master transmit mode • If the internal SCL line is high at the fall of SCL in master transmit mode 2 Bit 2—Slave Address Recognition Flag (AAS): In I C bus format slave receive mode, this flag is set to 1 if the first frame following a start condition matches bits SVA6 to SVA0 in SAR, or if the general call address (H'00) is detected. AAS is cleared by reading AAS after it has been set to 1, then writing 0 in AAS. In addition, AAS is reset automatically by write access to ICDR in transmit mode, or read access to ICDR in receive mode. Rev. 3.00 Mar 17, 2006 page 439 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 2 AAS Description 0 Slave address or general call address not recognized (Initial value) [Clearing conditions] 1 • When ICDR data is written (transmit mode) or read (receive mode) • When 0 is written in AAS after reading AAS = 1 • In master mode Slave address or general call address recognized [Setting condition] When the slave address or general call address is detected in slave receive mode while FS = 0 2 Bit 1—General Call Address Recognition Flag (ADZ): In I C bus format slave receive mode, this flag is set to 1 if the first frame following a start condition is the general call address (H'00). ADZ is cleared by reading ADZ after it has been set to 1, then writing 0 in ADZ. In addition, ADZ is reset automatically by write access to ICDR in transmit mode, or read access to ICDR in receive mode. Bit 1 ADZ Description 0 General call address not recognized (Initial value) [Clearing conditions] 1 • When ICDR data is written (transmit mode) or read (receive mode) • When 0 is written in ADZ after reading ADZ = 1 • In master mode General call address recognized [Setting condition] When the general call address is detected in slave receive mode while FSX = 0 or FS = 0 Rev. 3.00 Mar 17, 2006 page 440 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 0—Acknowledge Bit (ACKB): Stores acknowledge data. In transmit mode, after the receiving device receives data, it returns acknowledge data, and this data is loaded into ACKB. In receive mode, after data has been received, the acknowledge data set in this bit is sent to the transmitting device. When this bit is read, in transmission (when TRS = 1), the value loaded from the bus line (returned by the receiving device) is read. In reception (when TRS = 0), the value set by internal software is read. Also, when this bit is written, the set value of the acknowledge data to be issued upon receiving is rewritten, regardless of the TRS value. Since the value loaded from the receiving device is held, as is, in this case, care is required when rewriting this register using a bit operation command. Bit 0 ACKB Description 0 Receive mode: 0 is output at acknowledge output timing (Initial value) Transmit mode: Indicates that the receiving device has acknowledged the data (signal is 0) 1 Receive mode: 1 is output at acknowledge output timing Transmit mode: Indicates that the receiving device has not acknowledged the data (signal is 1) 16.2.7 Serial Timer Control Register (STCR) Bit 7 6 5 4 3 2 1 0 — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W STCR is an 8-bit readable/writable register that controls register access, the IIC interface operating mode (when the on-chip IIC option is included), selects the TCNT input clock source, and controls 2 the USB. For details of functions not related to the I C bus interface, see section 3.2.3, Serial Timer Control Register (STCR), and the descriptions of the relevant modules. If a module controlled by STCR is not used, do not write 1 to the corresponding bit. STCR is initialized to H'00 by a reset and in hardware standby mode. Bit 7—Reserved: This bit must not be set to 1. Rev. 3.00 Mar 17, 2006 page 441 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 2 Bits 6 and 5—I C Transfer Select 1 and 0 (IICX1, IICX0): These bits, together with bits CKS2 2 to CKS0 in ICMR, select the transfer rate in master mode. For details, see section 16.2.4, I C Bus Mode Register (ICMR). 2 2 Bit 4—I C Master Enable (IICE): Controls CPU access to the I C bus interface data and control registers (ICCR, ICSR, ICDR/SARX, ICMR/SAR). Bit 4 IICE Description 0 CPU access to I C bus interface data and control registers is disabled 2 (Initial value) 2 1 CPU access to I C bus interface data and control registers is enabled Bit 3—Reserved: This bit must not be set to 1. Bit 2—USB Enable (USBE): This bit controls CPU access to the USB data register and control register. Bit 2 USBE Description 0 Prohibition of the above register access 1 Permission of the above register access (Initial value) Bits 1 and 0—Internal Clock Source Select 1 and 0 (ICKS1, ICSK0): These bits, together with bits CKS2 to CKS0 in TCR, select the clock input to the timer counters (TCNT). For details, see section 12.2.4, Timer Control Register. 16.2.8 DDC Switch Register (DDCSWR) Bit Initial value Read/Write 7 6 5 4 3 2 1 0 SWE SW IE IF CLR3 CLR2 CLR1 CLR0 0 0 0 0 R/W R/(W)* 1 2 W* 1 2 W* 1 2 W* 1 2 W* R/W R/W 1 Notes: 1. Only 0 can be written, to clear the flag. 2. Always read as 1. DDCSWR is an 8-bit readable/writable register that controls the IIC channel 0 automatic format switching function. Rev. 3.00 Mar 17, 2006 page 442 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) DDCSWR is initialized to H'0F by a reset and in hardware standby mode. Bit 7—DDC Mode Switch Enable (SWE): Selects the function for automatically switching IIC 2 channel 0 from formatless mode to the I C bus format. Bit 7 SWE Description 0 Automatic switching of IIC channel 0 from formatless mode to I C bus format is disabled (Initial value) 1 Automatic switching of IIC channel 0 from formatless mode to I C bus format is enabled 2 2 2 Bit 6—DDC Mode Switch (SW): Selects either formatless mode or the I C bus format for IIC channel 0. Bit 6 SW Description 0 IIC channel 0 is used with the I C bus format 2 (Initial value) [Clearing conditions] 1 • When 0 is written by software • When a falling edge is detected on the SCL pin when SWE = 1 IIC channel 0 is used in formatless mode [Setting condition] When 1 is written in SW after reading SW = 0 Bit 5—DDC Mode Switch Interrupt Enable Bit (IE): Enables or disables an interrupt request to the CPU when automatic format switching is executed for IIC channel 0. Bit 5 IE Description 0 Interrupt when automatic format switching is executed is disabled 1 Interrupt when automatic format switching is executed is enabled (Initial value) Rev. 3.00 Mar 17, 2006 page 443 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Bit 4—DDC Mode Switch Interrupt Flag (IF): Flag that indicates an interrupt request to the CPU when automatic format switching is executed for IIC channel 0. Bit 4 IF Description 0 No interrupt is requested when automatic format switching is executed (Initial value) [Clearing condition] When 0 is written in IF after reading IF = 1 1 An interrupt is requested when automatic format switching is executed [Setting condition] When a falling edge is detected on the SCL pin when SWE = 1 Bits 3 to 0—IIC Clear 3 to 0 (CLR3 to CLR0): These bits control initialization of the internal state of IIC0 and IIC1. These bits can only be written to; if read they will always return a value of 1. When a write operation is performed on these bits, a clear signal is generated for the internal latch circuit of the corresponding module(s), and the internal state of the IIC module(s) is initialized. The write data for these bits is not retained. To perform IIC clearance, bits CLR3 to CLR0 must be written to simultaneously using an MOV instruction. Do not use a bit manipulation instruction such as BCLR. When clearing is required again, all the bits must be writen to in accordance with the setting. Bit 3 Bit 2 Bit 1 Bit 0 CLR3 CLR2 CLR1 CLR0 Description 0 0 — — Setting prohibited 1 0 0 Setting prohibited 1 IIC0 internal latch cleared 0 IIC1 internal latch cleared 1 IIC0 and IIC1 internal latches cleared — Invalid setting 1 1 — — Rev. 3.00 Mar 17, 2006 page 444 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.2.9 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers, and is used to perform module stop mode control. When the MSTP4 or MSTP3 bit is set to 1, operation of the corresponding IIC channel is halted at the end of the bus cycle, and a transition is made to module stop mode. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRL Bit 4—Module Stop (MSTP4): Specifies IIC channel 0 module stop mode. MSTPCRL Bit 4 MSTP4 Description 0 IIC channel 0 module stop mode is cleared 1 IIC channel 0 module stop mode is set (Initial value) MSTPCRL Bit 3—Module Stop (MSTP3): Specifies IIC channel 1 module stop mode. MSTPCRL Bit 3 MSTP3 Description 0 IIC channel 1 module stop mode is cleared 1 IIC channel 1 module stop mode is set (Initial value) Rev. 3.00 Mar 17, 2006 page 445 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3 Operation 16.3.1 I C Bus Data Format 2 2 2 The I C bus interface has serial and I C bus formats. 2 The I C bus formats are addressing formats with an acknowledge bit. These are shown in figures 16.3 (a) and (b). The first frame following a start condition always consists of 8 bits. IIC channel 0 only is capable of formatless operation, as shown in figure 16.3 (c). The serial format is a non-addressing format with no acknowledge bit. This is shown in figure 16.4. 2 Figure 16.5 shows the I C bus timing. The symbols used in figures 16.3 to 16.5 are explained in table 16.4. (a) I2C bus format (FS = 0 or FSX = 0) S SLA R/W A DATA A A/A P 1 7 1 1 n 1 1 1 1 n: transfer bit count (n = 1 to 8) m: transfer frame count (m ≥ 1) m (b) I2C bus format (start condition retransmission, FS = 0 or FSX = 0) S SLA R/W A DATA A/A S SLA R/W A DATA A/A P 1 7 1 1 n1 1 1 7 1 1 n2 1 1 1 m1 1 m2 n1 and n2: transfer bit count (n1 and n2 = 1 to 8) m1 and m2: transfer frame count (m1 and m2 ≥ 1) (c) Formatless (IIC0 only, FS = 0 or FSX = 0) DATA A 8 1 DATA n A A/A 1 1 1 m 2 n: transfer bit count (n = 1 to 8) m: transfer frame count (m ≥ 1) 2 Figure 16.3 I C Bus Data Formats (I C Bus Formats) Rev. 3.00 Mar 17, 2006 page 446 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) FS = 1 and FSX = 1 S DATA DATA P 1 8 n 1 1 m n: transfer bit count (n = 1 to 8) m: transfer frame count (m ≥ 1) 2 Figure 16.4 I C Bus Data Format (Serial Format) SDA SCL S 1-7 8 9 SLA R/W A 1-7 8 DATA 9 A 1-7 8 DATA 9 A/A P 2 Figure 16.5 I C Bus Timing 2 Table 16.4 Description of I C Bus Data Format Symbols S Indicates a start condition. When SCL is high level, the master device changes SDA from high to low level. SLA Indicates a slave address. The master device selects the slave device. R/W Indicates the transmit/receive direction. When the value of the R/W bit is 1, data is transferred from the slave device to the master device. When it is 0, data is transferred from the master device to the slave device. A Indicates an acknowledge response. The receiving device drives SDA low level. (In master transmit mode the slave device, and in master receive mode the master device, returns the acknowledge response.) DATA Indicates transmit/receive data. The bit length of the transmit/receive data is set by bits BC2 to BC0 in ICMR. The MLS bit in ICMR is used to select between MSB-first or LSBfirst format. P Indicates a stop condition. When SCL is high level, the master device changes SDA from low to high level. Rev. 3.00 Mar 17, 2006 page 447 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.2 Master Transmit Operation 2 In I C bus format master transmit mode, the master device outputs the transmit clock and transmit data, and the slave device returns an acknowledge signal. The transmission procedure and operations by which data is sequentially transmitted in synchronization with ICDR write operations, are described below. [1] Set the ICE bit in ICCR to 1. Set bits MLS, WAIT, and CKS2 to CKS0 in ICMR, and bit IICX in STCR, according to the operation mode. [2] Read the BBSY flag to confirm that the bus is free. [3] Set the MST and TRS bits to 1 in ICCR to select master transmit mode. [4] Write 1 to BBSY and 0 to SCP. This switches SDA from high to low when SCL is high, and generates the start condition. [5] When the start condition is generated, the IRIC and IRTR flags are set to 1. If the IEIC bit in ICCR has been set to 1, an interrupt request is sent to the CPU. [6] Write data to ICDR (slave address + R/W) With the I2C bus format (when the FS bit in SAR or the FSX bit in SARX is 0), the first frame data following the start condition indicates the 7-bit slave address and transmit/receive direction. Then clear the IRIC flag to indicate the end of transfer. Writing to ICDR and clearing of the IRIC flag must be executed continuously, so that no interrupt is inserted. If a period of time that is equal to transfer one byte has elapsed by the time the IRIC flag is cleared, the end of transfer cannot be identified. The master device sequentially sends the transmit clock and the data written to ICDR with the timing shown in Figure 16.6. The selected slave device (i.e., the slave device with the matching slave address) drives SDA low at the 9th transmit clock pulse and returns an acknowledge signal. [7] When one frame of data has been transmitted, the IRIC flag is set to 1 at the rise of the 9th transmit clock pulse. After one frame has been transmitted, SCL is automatically fixed low in synchronization with the internal clock until the next transmit data is written. [8] Read the ACKB bit to confirm that ACKB is 0. When the slave device has not returned an acknowledge signal and ACKB remains 1, execute the transmit end processing described in step [12] and perform transmit operation again. Rev. 3.00 Mar 17, 2006 page 448 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) [9] Write the next data to be transmitted in ICDR. To identify the end of data transfer, clear the IRIC flag to 0. As described in step [6] above, writing to ICDR and clearing of the IRIC flag must be executed continuously so that no interrupt is inserted. The next frame is transmitted in synchronization with the internal clock. [10] When one frame of data has been transmitted, the IRIC flag is set to 1 at the rise of the 9th transmit clock pulse. After one frame has been transmitted, SCL is automatically fixed low in synchronization with the internal clock until the next transmit data is written. [11] Read the ACKB bit of ICSR. Confirm that the slave device has returned an acknowledge signal and ACKB is 0. When more data is to be transmitted, return to step [9] to execute next transmit operation. If the slave device has not returned an acknowledge signal and ACKB is 1, execute the transmit end processing described in step [12]. [12] Clear the IRIC flag to 0. Write BBSY and CSP of ICCR to 0. By doing so, SDA is changed from low to high while SCL is high and the transmit stop condition is generated. Start condition generation SCL (Master output) 1 2 3 4 5 6 7 SDA (Master output) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Slave address SDA (Slave output) 8 Bit 0 R/W 1 2 Bit 7 Bit 6 9 [7] Data 1 A [5] IRIC IRTR ICDR Data 1 Address + R/W Precaution: Data set timing to ICDR Incorrect operation Normal operation User processing [4] Write 1 to BBSY [6] ICDR write and 0 to SCP (start condition generation) [6] IRIC clear [9] ICDR write [9] IRIC clear Figure 16.6 Example of Master Transmit Mode Operating Timing (MLS = WAIT = 0) Rev. 3.00 Mar 17, 2006 page 449 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.3 Master Receive Operation In master receive mode, the master device outputs the receive clock, receives data, and returns an acknowledge signal. The slave device transmits data. The transmission procedure and operations by which data is sequentially transmitted in synchronization with ICDR write operations, are described below. [1] Clear the TRS bit of ICCR to 0 and switch from transmit mode to receive mode. Set the WAIT bit to 1 and clear the ACKB bit of ICSR to 0 (acknowledge data setting). [2] When ICDR is read (dummy data read), reception is started and the receive clock is output, and data is received, in synchronization with the internal clock. To indicate the wait, clear the IRIC flag to 0. Reading from ICDR and clearing of the IRIC flag must be executed continuously so that no interrupt is inserted. If a period of time that is equal to transfer one byte has elapsed by the time the IRIC flag is cleared, the end of transfer cannot be identified. [3] The IRIC flag is set to 1 at the fall of the 8th clock of a one-frame reception clock. At this point, if the IEIC bit of ICCR is set to 1, an interrupt request is generated to the CPU. SCL is automatically fixed low in synchronization with the internal clock until the IRIC flag is cleared. If the first frame is the final reception frame, execute the end processing as described in [10]. [4] Clear the IRIC flag to 0 to negate the wait. The master device outputs the 9th receive clock pulse, sets SDA to low, and returns an acknowledge signal. [5] When one frame of data has been transmitted, the IRIC and IRTR flags are set to 1 at the rise of the 9th transmit clock pulse. The master device continues to output the receive clock for the next receive data. [6] Read the ICDR receive data. [7] Clear the IRIC flag to indicate the next wait. From clearing of the IRIC flag to negation of a wait as described in step [4] (and [9]) to clearing of the IRIC flag as described in steps [5], [6], and [7], must be performed within the time taken to transfer one byte. Rev. 3.00 Mar 17, 2006 page 450 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) [8] The IRIC flag is set to 1 at the fall of the 8th one-frame reception clock pulse. SCL is automatically fixed low in synchronization with the internal clock until the IRIC flag is cleared. If this frame is the final reception frame, execute the end processing as described in [10]. [9] Clear the IRIC flag to 0 to negate the wait. The master device outputs the 9th reception clock pulse, sets SDA to low, and returns an acknowledge signal. By repeating steps [5] to [9] above, more data can be received. [10] Set the ACKB bit of ICSR to 1 and set the acknowledge data for the final reception. Set the TRS bit of ICCR to 1 to change receive mode to transmit mode. [11] Clear the IRIC flag to negate the wait. [12] When one frame of data has been received, the IRIC flag is set to 1 at the rise of the 9th reception clock pulse. [13] Clear the WAIT bit of ICMR to 0 to cancel wait mode. Read the ICDR receive data and clear the IRIC flag to 0. Clear the IRIC flag only when WAIT = 0. If the stop-condition generation command is executed after clearing the IRIC flag to 0 and then clearing the WAIT bit to 0, the SDA line is fixed low and the stop condition cannot be generated. [14] Write 0 to BBSY and SCP. This changes SDA from low to high when SCL is high, and generates the stop condition. Rev. 3.00 Mar 17, 2006 page 451 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Master transmit mode Master receive mode SCL (Master output) 9 1 2 3 4 5 6 7 8 SDA (Slave output) A Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 9 [3] Data 1 SDA (Master output) [5] 1 2 3 4 5 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Data 2 A IRIC IRTR Data 1 ICDR User processing [1] TRS = 0 clear [2] ICDR read WAIT = 1 set (dummy read) ACKB = 0 clear [6] ICDR read (Data 1) [4] IRIC clear [7] IRIC clear [2] IRIC clear Figure 16.7 (1) Example of Master Receive Mode Operating Timing (MLS = ACKB = 0 and WAIT = 1) SCL (Master output) 8 9 SDA Bit 0 (Slave output) Data 2 [8] SDA (Master output) 1 2 3 4 5 6 7 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Data 3 [5] A 9 [8] 1 2 Bit 7 Bit 6 [5] Data 4 A IRIC IRTR ICDR Data 1 User processing Data 2 [6] ICDR read (Data 2) [9] IRIC clear Data 3 [6] ICDR read (Data 3) [7] IRIC clear [9] IRIC clear [7] IRIC clear Figure 16.7 (2) Example of Master Receive Mode Operating Timing (MLS = ACKB = 0 and WAIT = 1) 16.3.4 Slave Receive Operation In slave receive mode, the master device outputs the transmit clock and transmit data, and the slave device returns an acknowledge signal. The reception procedure and operations in slave receive mode are described below. [1] Set the ICE bit in ICCR to 1. Set the MLS bit in ICMR and the MST and TRS bits in ICCR according to the operating mode. [2] When the start condition output by the master device is detected, the BBSY flag in ICCR is set to 1. Rev. 3.00 Mar 17, 2006 page 452 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) [3] When the slave address matches in the first frame following the start condition, the device operates as the slave device specified by the master device. If the 8th data bit (R/W) is 0, the TRS bit in ICCR remains cleared to 0, and slave receive operation is performed. [4] At the 9th clock pulse of the receive frame, the slave device drives SDA low and returns an acknowledge signal. At the same time, the IRIC flag in ICCR is set to 1. If the IEIC bit in ICCR has been set to 1, an interrupt request is sent to the CPU. If the RDRF internal flag has been cleared to 0, it is set to 1, and the receive operation continues. If the RDRF internal flag has been set to 1, the slave device drives SCL low from the fall of the receive clock until data is read into ICDR. [5] Read ICDR and clear the IRIC flag in ICCR to 0. The RDRF flag is cleared to 0. Receive operations can be performed continuously by repeating steps [4] and [5]. When SDA is changed from low to high when SCL is high, and the stop condition is detected, the BBSY flag in ICCR is cleared to 0. Start condition generation SCL (master output) 1 2 3 Bit 7 Bit 6 Bit 5 4 5 6 7 Bit 4 Bit 3 Bit 2 8 9 1 2 SCL (slave output) SDA (master output) Slave address SDA (slave output) Bit 1 Bit 0 R/W Bit 7 Bit 6 Data 1 [4] A RDRF IRIC Interrupt request generation ICDRS Address + R/W ICDRR User processing Address + R/W [5] ICDR read [5] IRIC clearance Figure 16.8 Example of Slave Receive Mode Operation Timing (1) (MLS = ACKB = 0) Rev. 3.00 Mar 17, 2006 page 453 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) SCL (master output) 7 8 Bit 1 Bit 0 9 1 2 3 4 5 6 7 8 9 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SCL (slave output) SDA (master output) Data 1 SDA (slave output) Bit 7 [4] Bit 6 Data 2 A [4] A RDRF IRIC ICDRS Data 1 ICDRR Data 1 User processing Interrupt request generation Interrupt request generation [5] ICDR read Data 2 Data 2 [5] IRIC clearance Figure 16.9 Example of Slave Receive Mode Operation Timing (2) (MLS = ACKB = 0) Rev. 3.00 Mar 17, 2006 page 454 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.5 Slave Transmit Operation In slave transmit mode, the slave device outputs the transmit data, while the master device outputs the receive clock and returns an acknowledge signal. The transmission procedure and operations in slave transmit mode are described below. [1] Set the ICE bit in ICCR to 1. Set the MLS bit in ICMR and the MST and TRS bits in ICCR according to the operating mode. [2] When the slave address matches in the first frame following detection of the start condition, the slave device drives SDA low at the 9th clock pulse and returns an acknowledge signal. At the same time, the IRIC flag in ICCR is set to 1. If the IEIC bit in ICCR has been set to 1, an interrupt request is sent to the CPU. If the 8th data bit (R/W) is 1, the TRS bit in ICCR is set to 1, and the mode changes to slave transmit mode automatically. The TDRF internal flag is set to 1. The slave device drives SCL low from the fall of the transmit clock until ICDR data is written. [3] After clearing the IRIC flag to 0, write data to ICDR. The TDRE internal flag is cleared to 0. The written data is transferred to ICDRS, and the TDRE internal flag and the IRIC and IRTR flags are set to 1 again. After clearing the IRIC flag to 0, write the next data to ICDR. The slave device sequentially sends the data written into ICDR in accordance with the clock output by the master device at the timing shown in figure 16.10. [4] When one frame of data has been transmitted, the IRIC flag in ICCR is set to 1 at the rise of the 9th transmit clock pulse. If the TDRE internal flag has been set to 1, this slave device drives SCL low from the fall of the transmit clock until data is written to ICDR. The master device drives SDA low at the 9th clock pulse, and returns an acknowledge signal. As this acknowledge signal is stored in the ACKB bit in ICSR, this bit can be used to determine whether the transfer operation was performed normally. When the TDRE internal flag is 0, the data written into ICDR is transferred to ICDRS, transmission is started, and the TDRE internal flag and the IRIC and IRTR flags are set to 1 again. [5] To continue transmission, clear the IRIC flag to 0, then write the next data to be transmitted into ICDR. The TDRE flag is cleared to 0. Transmit operations can be performed continuously by repeating steps [4] and [5]. To end transmission, write H'FF to ICDR to release SDA on the slave side. When SDA is changed from low to high when SCL is high, and the stop condition is detected, the BBSY flag in ICCR is cleared to 0. Rev. 3.00 Mar 17, 2006 page 455 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Slave receive mode SCL (master output) 8 Slave transmit mode 9 1 2 3 4 5 6 7 8 A Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 9 1 2 SCL (slave output) SDA (slave output) SDA (master output) R/W Bit 7 Data 1 [2] Bit 6 Data 2 A TDRE Interrupt request generation IRIC [3] Interrupt request generation Interrupt request generation Data 1 ICDRT ICDRS Data 2 Data 1 User processing [3] IRIC [3] ICDR write clearance [3] ICDR write Data 2 [5] IRIC clearance [5] ICDR write Figure 16.10 Example of Slave Transmit Mode Operation Timing (MLS = 0) Rev. 3.00 Mar 17, 2006 page 456 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.6 IRIC Setting Timing and SCL Control The interrupt request flag (IRIC) is set at different times depending on the WAIT bit in ICMR, the FS bit in SAR, and the FSX bit in SARX. If the TDRE or RDRF internal flag is set to 1, SCL is automatically held low after one frame has been transferred; this timing is synchronized with the internal clock. Figure 16.11 shows the IRIC set timing and SCL control. (a) When WAIT = 0, and FS = 0 or FSX = 0 (I2C bus format, no wait) SCL 7 8 9 1 SDA 7 8 A 1 IRIC User processing Clear IRIC Write to ICDR (transmit) or read ICDR (receive) (b) When WAIT = 1, and FS = 0 or FSX = 0 (I2C bus format, wait inserted) SCL 8 9 1 SDA 8 A 1 IRIC Clear IRIC User processing Clear Write to ICDR (transmit) IRIC or read ICDR (receive) (c) When FS = 1 and FSX = 1 (synchronous serial format) SCL 7 8 1 SDA 7 8 1 IRIC User processing Clear IRIC Write to ICDR (transmit) or read ICDR (receive) Figure 16.11 IRIC Setting Timing and SCL Control Rev. 3.00 Mar 17, 2006 page 457 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.7 2 Automatic Switching from Formatless Mode to I C Bus Format Setting the SW bit to 1 in DDCSWR enables formatless mode to be selected as the IIC0 operating 2 mode. Switching from formatless mode to the I C bus format (slave mode) is performed automatically when a falling edge is detected on the SCL pin. The following four preconditions are necessary for this operation: • A common data pin (SDA) for formatless and I C bus format operation 2 • Separate clock pins for formatless operation (VSYNCI) and I C bus format operation (SCL) 2 • A fixed 1 level for the SCL pin during formatless operation (is not driven to low) • Settings of bits other than TRS in ICCR that allow I C bus format operation 2 2 Automatic switching is performed from formatless mode to the I C bus format when the SW bit in DDCSWR is automatically cleared to 0 on detection of a falling edge on the SCL pin. Switching 2 from the I C bus format to formatless mode is achieved by having software set the SW bit in DDCSWR to 1. 2 In formatless mode, bits (such as MSL and TRS) that control the I C bus interface operating mode 2 must not be modified. When switching from the I C bus format to formatless mode, set the TRS bit to 1 or clear it to 0 according to the transmit data (transmission or reception) in formatless 2 mode, then set the SW bit to 1. After automatic switching from formatless mode to the I C bus format (slave mode), in order to wait for slave address reception, the TRS bit is automatically cleared to 0. 2 If a falling edge is detected on the SCL pin during formatless operation, I C bus interface operation is deferred until a stop condition is detected. Rev. 3.00 Mar 17, 2006 page 458 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.3.8 Noise Canceler The logic levels at the SCL and SDA pins are routed through noise cancelers before being latched internally. Figure 16.12 shows a block diagram of the noise canceler circuit. The noise canceler consists of two cascaded latches and a match detector. The SCL (or SDA) input signal is sampled on the system clock, but is not passed forward to the next circuit unless the outputs of both latches agree. If they do not agree, the previous value is held. Sampling clock C SCL or SDA input signal D C Q Latch D Q Match detector Latch Internal SCL or SDA signal System clock period Sampling clock Figure 16.12 Block Diagram of Noise Canceler 16.3.9 Sample Flowcharts 2 Figures 16.13 to 16.16 show sample flowcharts for using the I C bus interface in each mode. Rev. 3.00 Mar 17, 2006 page 459 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Start Initialize [1] Initialize [2] Test the status of the SCL and SDA lines. [3] Select master transmit mode. [4] Start condition issuance [5] Wait for a start condition [6] Set transmit data for the first byte (slave address + R/W). (After writing ICDR, clear IRIC immediately) [7] Wait for 1 byte to be transmitted. [8] Test the acknowledge bit, transferred from slave device. Read BBSY in ICCR No BBSY = 0 ? Yes Set MST = 1 and TRS = 1 in ICCR Write BBSY = 1 and SCP = 0 in ICCR Read IRIC in ICCR No IRIC = 1 ? Yes Write transmit data in ICDR Clear IRIC in ICCR Read IRCI in ICCR No IRIC = 1 ? Yes Read ACKB in ICSR ACKB = 0 ? No Yes Transmit mode ? No Master receive mode Yes Write transmit data in ICDR Clear IRIC in ICCR Read IRIC in ICCR No [9] Set transmit data for the second and subsequent bytes. (After writing ICDR, clear IRIC immediately.) [10] Wait for 1 byte to be transmitted. IRIC = 1 ? Yes Read ACKB in ICSR No [11] Test for end of transfer End of transmission ? or ACKB = 1 ? Yes Clear IRIC in ICCR [12] Stop condition issuance Write BBSY = 0 and SCP = 0 in ICCR End Figure 16.13 Flowchart for Master Transmit Mode (Example) Rev. 3.00 Mar 17, 2006 page 460 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Master receive operation Set TRS = 0 in ICCR [1] Select receive mode. [2] Start receiving. The first read is a dummy read. After reading ICDR, please clear IRIC immediately. [3] Wait for 1 byte to be received (8th clock falling edge) [4] Clear IRIC to trigger the 9th clock. (to end the wait insertion) [5] Wait for 1 byte to be received. (9th clock rising edge) Read ICDR [6] Read the receive data. Clear IRIC in ICCR [7] Clear IRIC. [8] Wait for the next data to be received. (8th clock falling edge) [9] Clear IRIC to trigger the 9th clock. (to end the wait insertion) Set WAIT = 1 in ICMR Set ACKB = 0 in ICSR Read ICDR Clear IRIC in ICCR Read IRIC in ICCR No IRIC = 1 ? Yes Last receive ? Yes No Clear IRIC in ICCR Read IRIC in ICCR No IRIC = 1 ? Yes Read IRIC in ICCR No IRIC = 1 ? Yes Last receive ? Yes No Clear IRIC in ICCR Set ACKB = 1 in ICSR Set TRS = 1 in ICCR Clear IRIC in ICCR [10] Set ACKB = 1 so as to return No acknowledge, or set TRS = 1 so as not to issue Extra clock. [11] Clear IRIC to trigger the 9th clock (to end the wait insertion) Read IRIC in ICCR No IRIC = 1 ? [12] Wait for 1 byte to be received. Yes Set WAIT = 0 in ICMR Read ICDR Clear IRIC in ICCR Write BBSY = 0 and SCP = 0 in ICCR [13] Set WAIT = 0. Read ICDR. Clear IRIC. (Note: After setting WAIT = 0, IRIC should be cleared to 0.) [14] Stop condition issuance. End Figure 16.14 Flowchart for Master Receive Mode (Example) Rev. 3.00 Mar 17, 2006 page 461 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Start Initialize Set MST = 0 and TRS = 0 in ICCR [1] Set ACKB = 0 in ICSR Read IRIC in ICCR [2] No IRIC = 1? Yes Read AAS and ADZ in ICSR AAS = 1 and ADZ = 0? No General call address processing * Description omitted Yes Read TRS in ICCR No TRS = 0? Slave transmit mode Yes Last receive? Yes No Read ICDR [3] [1] Select slave receive mode. [2] Wait for the first byte to be received (slave address). Clear IRIC in ICCR [3] Start receiving. The first read is a dummy read. Read IRIC in ICCR No [4] Wait for the transfer to end. [4] IRIC = 1? [5] Set acknowledge data for the last receive. [6] Start the last receive. Yes [7] Wait for the transfer to end. Set ACKB = 1 in ICSR [5] Read ICDR [6] [8] Read the last receive data. Clear IRIC in ICCR Read IRIC in ICCR No [7] IRIC = 1? Yes Read ICDR [8] Clear IRIC in ICCR End Figure 16.15 Flowchart for Slave Receive Mode (Example) Rev. 3.00 Mar 17, 2006 page 462 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) Slave transmit mode Clear IRIC in ICCR Write transmit data in ICDR [1] [1] Set transmit data for the second and subsequent bytes. [2] Wait for 1 byte to be transmitted. Clear IRIC in ICCR [3] Test for end of transfer. [4] Select slave receive mode. Read IRIC in ICCR No [2] [5] Dummy read (to release the SCL line). IRIC = 1? Yes Read ACKB in ICSR No [3] End of transmission (ACKB = 1)? Yes Set TRS = 0 in ICCR [4] Read ICDR [5] Clear IRIC in ICCR End Figure 16.16 Flowchart for Slave Transmit Mode (Example) 16.3.10 Initialization of Internal State The IIC has a function for forcible initialization of its internal state if a deadlock occurs during communication. Initialization is executed in accordance with the setting of bits CLR3 to CLR0 in the DDCSWR register or clearing ICE bit. For details the setting of bits CLR3 to CLR0, see section 16.2.8, DDC Switch Register (DDCSWR). Scope of Initialization: The initialization executed by this function covers the following items: • TDRE and RDRF internal flags • Transmit/receive sequencer and internal operating clock counter Rev. 3.00 Mar 17, 2006 page 463 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • Internal latches for retaining the output state of the SCL and SDA pins (wait, clock, data output, etc.) The following items are not initialized: • Actual register values (ICDR, SAR, SARX, ICMR, ICCR, ICSR, DDCSWR, STCR) • Internal latches used to retain register read information for setting/clearing flags in the ICMR, ICCR, ICSR, and DDCSWR registers • The value of the ICMR register bit counter (BC2 to BC0) • Generated interrupt sources (interrupt sources transferred to the interrupt controller) Notes on Initialization: • Interrupt flags and interrupt sources are not cleared, and so flag clearing measures must be taken as necessary. • Basically, other register flags are not cleared either, and so flag clearing measures must be taken as necessary. • When initialization is executed by the DDCSWR register, the write data for bits CLR3 to CLR0 is not retained. To perform IIC clearance, bits CLR3 to CLR0 must be written to simultaneously using an MOV instruction. Do not use a bit manipulation instruction such as BCLR. Similarly, when clearing is required again, all the bits must be written to simultaneously in accordance with the setting. • If a flag clearing setting is made during transmission/reception, the IIC module will stop transmitting/receiving at that point and the SCL and SDA pins will be released. When transmission/reception is started again, register initialization, etc., must be carried out as necessary to enable correct communication as a system. The value of the BBSY bit cannot be modified directly by this module clear function, but since the stop condition pin waveform is generated according to the state and release timing of the SCL and SDA pins, the BBSY bit may be cleared as a result. Similarly, state switching of other bits and flags may also have an effect. To prevent problems caused by these factors, the following procedure should be used when initializing the IIC state. 1. Execute initialization of the internal state according to the setting of bits CLR3 to CLR0. 2. Execute a stop condition issuance instruction (write 0 to BBSY and SCP) to clear the BBSY bit to 0, and wait for two transfer rate clock cycles. 3. Re-execute initialization of the internal state according to the setting of bits CLR3 to CLR0. 4. Initialize (re-set) the IIC registers. Rev. 3.00 Mar 17, 2006 page 464 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 16.4 Usage Notes • In master mode, if an instruction to generate a start condition is immediately followed by an instruction to generate a stop condition, neither condition will be output correctly. To output consecutive start and stop conditions, after issuing the instruction that generates the start condition, read the relevant ports, check that SCL and SDA are both low, then issue the instruction that generates the stop condition. Note that SCL may not yet have gone low when BBSY is cleared to 0. • Either of the following two conditions will start the next transfer. Pay attention to these conditions when reading or writing to ICDR. Write access to ICDR when ICE = 1 and TRS = 1 (including automatic transfer from ICDRT to ICDRS) Read access to ICDR when ICE = 1 and TRS = 0 (including automatic transfer from ICDRS to ICDRR) • Table 16.5 shows the timing of SCL and SDA output in synchronization with the internal clock. Timings on the bus are determined by the rise and fall times of signals affected by the bus load capacitance, group resistance, and parallel resistance. 2 Table 16.5 I C Bus Timing (SCL and SDA Output) Item Symbol Output Timing Unit Notes SCL output cycle time tSCLO 28tcyc to 256tcyc ns SCL output high pulse width tSCLHO 0.5tSCLO ns Figure 22.18 (reference) SCL output low pulse width tSCLLO 0.5tSCLO ns SDA output bus free time tBUFO 0.5tSCLO – 1tcyc ns Start condition output hold time tSTAHO 0.5tSCLO – 1tcyc ns Retransmission start condition output setup time tSTASO 1tSCLO ns Stop condition output setup time tSTOSO 0.5tSCLO + 2tcyc ns Data output setup time (master) tSDASO 1tSCLLO – 3tcyc ns 1tSCLL – (6tcyc or 12tcyc*) Data output setup time (slave) Data output hold time Note: * tSDAHO 3tcyc ns 6tcyc when IICX is 0, 12tcyc when 1. Rev. 3.00 Mar 17, 2006 page 465 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • SCL and SDA input is sampled in synchronization with the internal clock. The AC timing therefore depends on the system clock cycle tcyc, as shown in table 22.8 in section 22, Electrical 2 Characteristics. Note that the I C bus interface AC timing specifications will not be met with a system clock frequency of less than 5 MHz. • The I C bus interface specification for the SCL rise time tsr is under 1000 ns (300 ns for high2 speed mode). In master mode, the I C bus interface monitors the SCL line and synchronizes one bit at a time during communication. If tsr (the time for SCL to go from low to VIH) exceeds 2 the time determined by the input clock of the I C bus interface, the high period of SCL is extended. The SCL rise time is determined by the pull-up resistance and load capacitance of the SCL line. To insure proper operation at the set transfer rate, adjust the pull-up resistance and load capacitance so that the SCL rise time does not exceed the values given in the table below. 2 Table 16.6 Permissible SCL Rise Time (tSR) Values Time Indication 2 IICX tcyc Indication 0 7.5tcyc 1 17.5tcyc I C Bus Specification (Max.) φ= 5 MHz Normal mode 1000 ns High-speed mode φ= 8 MHz φ= 10 MHz φ= φ= 16 MHz 20 MHz 1000 ns 937 ns 750 ns 468 ns 375 ns 300 ns 300 ns 300 ns 300 ns 300 ns Normal mode 1000 ns 1000 ns 1000 ns 1000 ns 1000 ns 875 ns High-speed mode 300 ns 300 ns 300 ns 300 ns 300 ns 300 ns 300 ns • The I C bus interface specifications for the SCL and SDA rise and fall times are under 1000 ns 2 and 300 ns. The I C bus interface SCL and SDA output timing is prescribed by tcyc, as shown in 2 table 16.6. However, because of the rise and fall times, the I C bus interface specifications may not be satisfied at the maximum transfer rate. Table 16.7 shows output timing calculations for different operating frequencies, including the worst-case influence of rise and fall times. 2 2 tBUFO fails to meet the I C bus interface specifications at any frequency. The solution is either (a) to provide coding to secure the necessary interval (approximately 1 µs) between issuance of a stop condition and issuance of a start condition, or (b) to select devices whose input timing 2 permits this output timing for use as slave devices connected to the I C bus. 2 tSCLLO in high-speed mode and tSTASO in standard mode fail to satisfy the I C bus interface specifications for worst-case calculations of tSr/tSf. Possible solutions that should be investigated include (a) adjusting the rise and fall times by means of a pull-up resistor and capacitive load, (b) reducing the transfer rate to meet the specifications, or (c) selecting devices whose input 2 timing permits this output timing for use as slave devices connected to the I C bus. Rev. 3.00 Mar 17, 2006 page 466 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) 2 Table 16.7 I C Bus Timing (with Maximum Influence of tSr/tSf) Time Indication (at Maximum Transfer Rate) [ns] Item tSCLHO tSCLLO tBUFO tSTAHO tSTASO tSTOSO tcyc Indication I2C Bus tSr/tSf SpecifiInfluence cation (Min.) (Max.) φ= 5 MHz φ= 8 MHz φ= φ= φ= 10 MHz 16 MHz 20 MHz 0.5tSCLO (–tSr) Standard mode –1000 4000 4000 4000 4000 4000 4000 High-speed mode –300 600 950 950 950 950 950 0.5tSCLO (–tSf ) Standard mode –250 4700 4750 4750 4750 4750 4750 –250 1300 1000*1 1000*1 1000*1 1000*1 1000*1 –1000 4700 3800*1 3875*1 3900*1 3938*1 3950*1 –300 1300 750*1 825*1 850*1 888*1 900*1 –250 4000 4550 4625 4650 4688 4700 –250 600 800 875 900 938 950 Standard mode –1000 4700 9000 9000 9000 9000 9000 High-speed mode –300 600 2200 2200 2200 2200 2200 High-speed mode 0.5tSCLO Standard mode –1tcyc ( –tSr ) High-speed mode 0.5tSCLO Standard mode –1tcyc (–tSf ) High-speed mode 1tSCLO (–tSr ) Standard mode –1000 4000 4400 4250 4200 4125 4100 High-speed mode –300 600 1350 1200 1150 1075 1050 –1000 250 3100 3325 3400 3513 3550 (master) 1tSCLLO*3 Standard mode –3tcyc (–tSr ) High-speed mode –300 100 400 625 700 813 850 tSDASO (slave) 1tSCLL*3 –12t *2 –1000 250 1300 2200 2500 2950 3100 400 tSDASO 0.5tSCLO + 2tcyc (–tSr ) cyc (–tSr ) tSDAHO 3tcyc Standard mode High-speed mode –300 100 –1400*1 –500*1 –200*1 250 Standard mode 0 0 600 375 300 188 150 High-speed mode 0 0 600 375 300 188 150 2 Notes: 1. Does not meet the I C bus interface specification. Remedial action such as the following is necessary: (a) secure a start/stop condition issuance interval; (b) adjust the rise and fall times by means of a pull-up resistor and capacitive load; (c) reduce the transfer rate; (d) select slave devices whose input timing permits this output timing. The values in the above table will vary depending on the settings of the IICX bit and bits CKS0 to CKS2. Depending on the frequency it may not be possible to achieve the 2 maximum transfer rate; therefore, whether or not the I C bus interface specifications are met must be determined in accordance with the actual setting conditions. 2. Value when the IICX bit is set to 1. When the IICX bit is cleared to 0, the value is (tSCLL – 6tcyc). 2 3. Calculated using the I C bus specification values (standard mode: 4700 ns min.; highspeed mode: 1300 ns min.). Rev. 3.00 Mar 17, 2006 page 467 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • Note on ICDR Read at End of Master Reception To halt reception at the end of a receive operation in master receive mode, set the TRS bit to 1 and write 0 to BBSY and SCP in ICCR. This changes SDA from low to high when SCL is high, and generates the stop condition. After this, receive data can be read by means of an ICDR read, but if data remains in the buffer the ICDRS receive data will not be transferred to ICDR, and so it will not be possible to read the second byte of data. If it is necessary to read the second byte of data, issue the stop condition in master receive mode (i.e. with the TRS bit cleared to 0). When reading the receive data, first confirm that the BBSY bit in the ICCR register is cleared to 0, the stop condition has been generated, and the bus has been released, then read the ICDR register with TRS cleared to 0. Note that if the receive data (ICDR data) is read in the interval between execution of the instruction for issuance of the stop condition (writing of 0 to BBSY and SCP in ICCR) and the actual generation of the stop condition, the clock may not be output correctly in subsequent master transmission. Clearing of the MST bit after completion of master transmission/reception, or other modifications of IIC control bits to change the transmit/receive operating mode or settings, must be carried out during interval (a) in figure 16.17 (after confirming that the BBSY bit has been cleared to 0 in the ICCR register). Stop condition Start condition (a) SDA Bit 0 A SCL 8 9 Internal clock BBSY bit Master receive mode ICDR reading prohibited Execution of stop condition issuance instruction (0 written to BBSY and SCP) Confirmation of stop condition generation (0 read from BBSY) Start condition issuance Figure 16.17 Points for Attention Concerning Reading of Master Receive Data Rev. 3.00 Mar 17, 2006 page 468 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • Notes on Start Condition Issuance for Retransmission Figure 16.18 shows the timing of start condition issuance for retransmission, and the timing for subsequently writing data to ICDR, together with the corresponding flowchart. After start condition issuance is done and determined the start condition, write the transmit data to ICDR, as shown below. IRIC = 1 ? No [1] Yes Clear IRIC in ICSR Start condition issuance ? No Wait for end of 1-byte transfer [2] Determine whether SCL is low [3] Issue restart condition instruction for transmission [4] Detremine whether start condition is generated or not [5] Set transmit data (slave address + R/W) Other processing Yes [2] Read SCL pin SCL = Low ? [1] Note: Program so that processing from [3] to [5] is executed continuously. No Yes Write BBSY = 1, SCP = 0 (ICSR) IRIC = 1 ? [3] No [4] Yes [5] Write transmit data to ICDR start condition (retransmission) 9 SCL SDA ACK bit7 Data output IRIC [3] Start condition instruction issuance [1] IRIC determination [2] Determination of SCL = Low [4] IRIC determination [5] ICDR write (next transmit data) Figure 16.18 Flowchart and Timing of Start Condition Instruction Issuance for Retransmission Rev. 3.00 Mar 17, 2006 page 469 of 706 REJ09B0303-0300 2 Section 16 I C Bus Interface (IIC) • Notes on I C Bus Interface Stop Condition Instruction Issuance 2 If the rise time of the 9th SCL clock exceeds the specification because the bus load capacitance is large, or if there is a slave device of the type that drives SCL low to effect a wait, after rising of the 9th SCL clock, issue the stop condition after reading SCL and determining it to below, as shown below. SCL 9th clock VIH High period secured As waveform rise is late, SCL is detected as low SDA Stop condition IRIC [1] Determination of SCL = Low [2] Stop condition instruction isuuance Figure 16.19 Timing of Stop Condition Issuance Rev. 3.00 Mar 17, 2006 page 470 of 706 REJ09B0303-0300 Section 17 A/D Converter Section 17 A/D Converter 17.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip 10-bit successive-approximations A/D converter that allows up to eight analog input channels to be selected. The H8/3577 Group has eight analog input channels, and the H8/3567 Group has four. 17.1.1 Features A/D converter features are listed below. • 10-bit resolution (analog input) • Input channels 8 channels (H8/3577 Group) 4 channels (H8/3567 Group) • Settable analog conversion voltage range The analog conversion voltage range is set using the analog power supply voltage pin (AVcc) as the analog reference voltage • High-speed conversion Minimum conversion time: 6.7 µs per channel (at 20 MHz operation) • Choice of single mode or scan mode Single mode: Single-channel A/D conversion Scan mode: Continuous A/D conversion on 1 to 4 channels • Four data registers Conversion results are held in a 16-bit data register for each channel • Sample and hold function • Three kinds of conversion start Choice of software or timer conversion start trigger (8-bit timer), or ADTRG pin • A/D conversion end interrupt generation An A/D conversion end interrupt (ADI) request can be generated at the end of A/D conversion Rev. 3.00 Mar 17, 2006 page 471 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.1.2 Block Diagram Figure 17.1 shows a block diagram of the A/D converter. Internal data bus AVSS ADCR ADCSR ADDRD ADDRC ADDRB + – Multiplexer H8/3577 Group only AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 ADDRA 10-bit D/A Successive approximations register AVCC Bus interface Module data bus Comparator φ/8 Control circuit Sample-andhold circuit φ/16 ADI interrupt signal ADTRG Legend: ADCR: ADCSR: ADDRA: ADDRB: ADDRC: ADDRD: Conversion start trigger from 8-bit timer A/D control register A/D control/status register A/D data register A A/D data register B A/D data register C A/D data register D Figure 17.1 Block Diagram of A/D Converter Rev. 3.00 Mar 17, 2006 page 472 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.1.3 Pin Configuration Table 17.1 summarizes the input pins used by the A/D converter. The AVCC and AVSS pins are the power supply pins for the analog block in the A/D converter. Table 17.1 A/D Converter Pins Pin Name Symbol I/O Function Analog power supply pin AVCC Input Analog block power supply Analog ground pin AVSS Input Analog block ground and A/D conversion reference voltage Analog input pin 0 AN0 Input Analog input channel 0 Analog input pin 1 AN1 Input Analog input channel 1 Analog input pin 2 AN2 Input Analog input channel 2 Analog input pin 3 AN3 Input Analog input channel 3 Analog input pin 4 AN4 Input Analog input channel 4 (H8/3577 Group only) Analog input pin 5 AN5 Input Analog input channel 5 (H8/3577 Group only) Analog input pin 6 AN6 Input Analog input channel 6 (H8/3577 Group only) Analog input pin 7 AN7 Input Analog input channel 7 (H8/3577 Group only) A/D external trigger input pin ADTRG Input External trigger input for starting A/D conversion Rev. 3.00 Mar 17, 2006 page 473 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.1.4 Register Configuration Table 17.2 summarizes the registers of the A/D converter. Table 17.2 A/D Converter Registers Name Abbreviation R/W Initial Value Address A/D data register AH ADDRAH R H'00 H'FFE0 A/D data register AL ADDRAL R H'00 H'FFE1 A/D data register BH ADDRBH R H'00 H'FFE2 A/D data register BL ADDRBL R H'00 H'FFE3 A/D data register CH ADDRCH R H'00 H'FFE4 A/D data register CL ADDRCL R H'00 H'FFE5 A/D data register DH ADDRDH R H'00 H'FFE6 A/D data register DL ADDRDL R H'00 H'FFE7 A/D control/status register ADCSR R/(W)* H'00 H'FFE8 A/D control register ADCR R/W H'3F H'FFE9 Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 Note: Only 0 can be written in bit 7, to clear the flag. * 17.2 Register Descriptions 17.2.1 A/D Data Registers A to D (ADDRA to ADDRD) Bit 5 4 3 2 1 0 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 — 15 14 13 12 11 10 9 8 7 6 — — — — — Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R There are four 16-bit read-only ADDR registers, ADDRA to ADDRD, used to store the results of A/D conversion. Rev. 3.00 Mar 17, 2006 page 474 of 706 REJ09B0303-0300 Section 17 A/D Converter The 10-bit data resulting from A/D conversion is transferred to the ADDR register for the selected channel and stored there. The upper 8 bits of the converted data are transferred to the upper byte (bits 15 to 8) of ADDR, and the lower 2 bits are transferred to the lower byte (bits 7 and 6) and stored. Bits 5 to 0 are always read as 0. The correspondence between the analog input channels and ADDR registers is shown in table 17.3. The ADDR registers can always be read by the CPU. The upper byte can be read directly, but for the lower byte, data transfer is performed via a temporary register (TEMP). For details, see section 17.3, Interface to Bus Master. The ADDR registers are initialized to H'0000 by a reset, and in standby mode, and module stop mode. Table 17.3 Analog Input Channels and Corresponding ADDR Registers Analog Input Channel Group 0 Group 1 A/D Data Register AN0 AN4 ADDRA AN1 AN5 ADDRB AN2 AN6 ADDRC AN3 AN7 ADDRD 17.2.2 A/D Control/Status Register (ADCSR) Bit 7 6 5 4 3 2 1 0 ADF ADIE ADST SCAN CKS CH2 CH1 CH0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/W R/W R/W R/W R/W R/W R/W Note: * Only 0 can be written in bit 7, to clear the flag. ADCSR is an 8-bit readable/writable register that controls A/D conversion operations. ADCSR is initialized to H'00 by a reset, and in standby mode, and module stop mode. Rev. 3.00 Mar 17, 2006 page 475 of 706 REJ09B0303-0300 Section 17 A/D Converter Bit 7—A/D End Flag (ADF): Status flag that indicates the end of A/D conversion. Bit 7 ADF Description 0 [Clearing condition] (Initial value) When 0 is written in the ADF flag after reading ADF = 1 1 [Setting conditions] • Single mode: When A/D conversion ends • Scan mode: When A/D conversion ends on all specified channels Bit 6—A/D Interrupt Enable (ADIE): Selects enabling or disabling of interrupt (ADI) requests at the end of A/D conversion. Bit 6 ADIE Description 0 A/D conversion end interrupt (ADI) request is disabled 1 A/D conversion end interrupt (ADI) request is enabled (Initial value) Bit 5—A/D Start (ADST): Selects starting or stopping of A/D conversion. Holds a value of 1 during A/D conversion. The ADST bit can be set to 1 by software, a timer conversion start trigger, or the A/D external trigger input pin (ADTRG). Bit 5 ADST Description 0 A/D conversion stopped 1 Single mode: A/D conversion is started. Cleared to 0 automatically when conversion on the specified channel ends (Initial value) Scan mode: A/D conversion is started. Conversion continues sequentially on the selected channels until ADST is cleared to 0 by software, a reset, or a transition to standby mode or module stop mode Rev. 3.00 Mar 17, 2006 page 476 of 706 REJ09B0303-0300 Section 17 A/D Converter Bit 4—Scan Mode (SCAN): Selects single mode or scan mode as the A/D conversion operating mode. See section 17.4, Operation, for single mode and scan mode operation. Only set the SCAN bit while conversion is stopped. Bit 4 SCAN Description 0 Single mode 1 Scan mode (Initial value) Bit 3—Clock Select (CKS): Sets the A/D conversion time. Only change the conversion time while ADST = 0. Bit 3 CKS Description 0 Conversion time = 266 states (max.) 1 Conversion time = 134 states (max.) (Initial value) Bits 2 to 0—Channel Select 2 to 0 (CH2 to CH0): Together with the SCAN bit, these bits select the analog input channel(s). Only set the input channel while conversion is stopped. Group Selection H8/3577 Group and H8/3567 Group H8/3577 Group only Channel Selection Description CH2 CH1 CH0 Single Mode Scan Mode 0 0 0 AN0 (Initial value) AN0 1 AN1 AN0, AN1 1 0 AN2 AN0 to AN2 1 AN3 AN0 to AN3 0 0 AN4 AN4 1 AN5 AN4, AN5 0 AN6 AN4, AN5, AN6 1 AN7 AN4 to AN7 1 1 Rev. 3.00 Mar 17, 2006 page 477 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.2.3 A/D Control Register (ADCR) Bit 7 6 5 4 3 2 1 0 TRGS1 TRGS0 — — — — — — Initial value 0 0 1 1 1 1 1 1 Read/Write R/W R/W — — — — — — ADCR is an 8-bit readable/writable register that enables or disables external triggering of A/D conversion operations. ADCR is initialized to H'3F by a reset, and in standby mode, and module stop mode. Bits 7 and 6—Timer Trigger Select 1 and 0 (TRGS1, TRGS0): These bits select enabling or disabling of the start of A/D conversion by a trigger signal. Only set bits TRGS1 and TRGS0 while conversion is stopped. Bit 7 Bit 6 TRGS1 TRGS0 Description 0 0 Start of A/D conversion by external trigger is disabled 1 Start of A/D conversion by external trigger is disabled 0 Start of A/D conversion by external trigger (8-bit timer) is enabled 1 Start of A/D conversion by external trigger pin is enabled 1 Bits 5 to 0—Reserved: These bits cannot be modified and are always read as 1. Rev. 3.00 Mar 17, 2006 page 478 of 706 REJ09B0303-0300 (Initial value) Section 17 A/D Converter 17.2.4 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR, comprising two 8-bit readable/writable registers, performs module stop mode control. When the MSTP9 bit in MSTPCR is set to 1, A/D converter operation stops at the end of the bus cycle and a transition is made to module stop mode. Registers cannot be read or written to in module stop mode. For details, see section 21.5, Module Stop Mode. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTPCRH Bit 1—Module Stop (MSTP9): Specifies the A/D converter module stop mode. MSTPCRH Bit 1 MSTP9 Description 0 A/D converter module stop mode is cleared 1 A/D converter module stop mode is set (Initial value) Rev. 3.00 Mar 17, 2006 page 479 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.3 Interface to Bus Master ADDRA to ADDRD are 16-bit registers, but the data bus to the bus master is only 8 bits wide. Therefore, in accesses by the bus master, the upper byte is accessed directly, but the lower byte is accessed via a temporary register (TEMP). A data read from ADDR is performed as follows. When the upper byte is read, the upper byte value is transferred to the CPU and the lower byte value is transferred to TEMP. Next, when the lower byte is read, the TEMP contents are transferred to the CPU. When reading ADDR, always read the upper byte before the lower byte. It is possible to read only the upper byte, but if only the lower byte is read, incorrect data may be obtained. Figure 17.2 shows the data flow for ADDR access. Upper byte read Bus master (H'AA) Module data bus Bus interface TEMP (H'40) ADDRnH (H'AA) ADDRnL (H'40) (n = A to D) Lower byte read Bus master (H'40) Module data bus Bus interface TEMP (H'40) ADDRnH (H'AA) ADDRnL (H'40) (n = A to D) Figure 17.2 ADDR Access Operation (Reading H'AA40) Rev. 3.00 Mar 17, 2006 page 480 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.4 Operation The A/D converter operates by successive approximations with 10-bit resolution. It has two operating modes: single mode and scan mode. 17.4.1 Single Mode (SCAN = 0) Single mode is selected when A/D conversion is to be performed on a single channel only. A/D conversion is started when the ADST bit is set to 1 by software, or by external trigger input. The ADST bit remains set to 1 during A/D conversion, and is automatically cleared to 0 when conversion ends. On completion of conversion, the ADF flag is set to 1. If the ADIE bit is set to 1 at this time, an ADI interrupt request is generated. The ADF flag is cleared by writing 0 after reading ADCSR. When the operating mode or analog input channel must be changed during analog conversion, to prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be set at the same time as the operating mode or input channel is changed. Typical operations when channel 1 (AN1) is selected in single mode are described next. Figure 17.3 shows a timing diagram for this example. 1. Single mode is selected (SCAN = 0), input channel AN1 is selected (CH1 = 0, CH0 = 1), the A/D interrupt is enabled (ADIE = 1), and A/D conversion is started (ADST = 1). 2. When A/D conversion is completed, the result is transferred to ADDRB. At the same time the ADF flag is set to 1, the ADST bit is cleared to 0, and the A/D converter becomes idle. 3. Since ADF = 1 and ADIE = 1, an ADI interrupt is requested. 4. The A/D interrupt handling routine starts. 5. The routine reads ADCSR, then writes 0 to the ADF flag. 6. The routine reads and processes the conversion result (ADDRB). 7. Execution of the A/D interrupt handling routine ends. After that, if the ADST bit is set to 1, A/D conversion starts again and steps 2 to 7 are repeated. Rev. 3.00 Mar 17, 2006 page 481 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 482 of 706 REJ09B0303-0300 Idle Idle Idle State of channel 1 (AN1) State of channel 2 (AN2) State of channel 3 (AN3) A/D conversion 1 Set* A/D conversion 2 Set* A/D conversion result 1 Read conversion result Idle Clear* Note: * Vertical arrows ( ) indicate instructions executed by software. ADDRD ADDRC ADDRB ADDRA Idle A/D conversion starts State of channel 0 (AN0) ADF ADST ADIE Set* A/D conversion result 2 Read conversion result Idle Clear* Section 17 A/D Converter Figure 17.3 Example of A/D Converter Operation (Single Mode, Channel 1 Selected) Section 17 A/D Converter 17.4.2 Scan Mode (SCAN = 1) Scan mode is useful for monitoring analog inputs in a group of one or more channels. When the ADST bit is set to 1 by software, or by timer or external trigger input, A/D conversion starts on the first channel in the group (AN0 when CH2 = 0; AN4 when CH2 = 1). When two or more channels are selected, after conversion of the first channel ends, conversion of the second channel (AN1 or AN5) starts immediately. A/D conversion continues cyclically on the selected channels until the ADST bit is cleared to 0. The conversion results are transferred for storage into the ADDR registers corresponding to the channels. When the operating mode or analog input channel must be changed during analog conversion, to prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be set at the same time as the operating mode or input channel is changed. Typical operations when three channels (AN0 to AN2) are selected in scan mode are described next. Figure 17.4 shows a timing diagram for this example. 1. Scan mode is selected (SCAN = 1), scan group 0 is selected (CH2 = 0), analog input channels AN0 to AN2 are selected (CH1 = 1, CH0 = 0), and A/D conversion is started (ADST = 1) 2. When A/D conversion of the first channel (AN0) is completed, the result is transferred to ADDRA. Next, conversion of the second channel (AN1) starts automatically. 3. Conversion proceeds in the same way through the third channel (AN2). 4. When conversion of all the selected channels (AN0 to AN2) is completed, the ADF flag is set to 1 and conversion of the first channel (AN0) starts again. If the ADIE bit is set to 1 at this time, an ADI interrupt is requested after A/D conversion ends. 5. Steps 2 to 4 are repeated as long as the ADST bit remains set to 1. When the ADST bit is cleared to 0, A/D conversion stops. After that, if the ADST bit is set to 1, A/D conversion starts again from the first channel (AN0). Rev. 3.00 Mar 17, 2006 page 483 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 484 of 706 REJ09B0303-0300 Figure 17.4 Example of A/D Converter Operation (Scan Mode, Channels AN0 to AN2 Selected) Idle Idle Idle A/D conversion 1 Transfer 2. Data currently being converted is ignored. Idle A/D conversion 3 Idle A/D conversion result 3 A/D conversion result 2 A/D conversion result 4 Idle Idle Idle Clear*1 A/D conversion 5 *2 A/D conversion time A/D conversion 4 A/D conversion result 1 A/D conversion 2 Idle Notes: 1. Vertical arrows ( ) indicate instructions executed by software. ADDRD ADDRC ADDRB ADDRA State of channel 3 (AN3) State of channel 2 (AN2) State of channel 1 (AN1) State of channel 0 (AN0) ADF ADST Set*1 Continuous A/D conversion execution Clear*1 Section 17 A/D Converter Section 17 A/D Converter 17.4.3 Input Sampling and A/D Conversion Time The A/D converter has a built-in sample-and-hold circuit. The A/D converter samples the analog input at a time tD after the ADST bit is set to 1, then starts conversion. Figure 17.5 shows the A/D conversion timing. Table 17.4 indicates the A/D conversion time. As indicated in figure 17.5, the A/D conversion time includes tD and the input sampling time. The length of tD varies depending on the timing of the write access to ADCSR. The total conversion time therefore varies within the ranges indicated in table 17.4. In scan mode, the values given in table 17.4 apply to the first conversion time. In the second and subsequent conversions the conversion time is fixed at 256 states when CKS = 0 or 128 states when CKS = 1. (1) φ Address (2) Write signal Input sampling timing ADF tD t SPL t CONV Legend: (1): ADCSR write cycle (2): ADCSR address tD: A/D conversion start delay tSPL: Input sampling time tCONV: A/D conversion time Figure 17.5 A/D Conversion Timing Rev. 3.00 Mar 17, 2006 page 485 of 706 REJ09B0303-0300 Section 17 A/D Converter Table 17.4 A/D Conversion Time (Single Mode) CKS = 0 CKS = 1 Item Symbol Min Typ Max Min Typ Max A/D conversion start delay tD 10 — 17 6 — 9 Input sampling time tSPL — 63 — — 31 — A/D conversion time tCONV 259 — 266 131 — 134 Note: Values in the table are the number of states. 17.4.4 External Trigger Input Timing A/D conversion can be externally triggered. When the TRGS1 and TRGS0 bits are set to 11 in ADCR, external trigger input is enabled at the ADTRG pin. A falling edge at the ADTRG pin sets the ADST bit to 1 in ADCSR, starting A/D conversion. Other operations, in both single and scan modes, are the same as when the ADST bit is set to 1 by software. Figure 17.6 shows the timing. φ ADTRG Internal trigger signal ADST A/D conversion Figure 17.6 External Trigger Input Timing 17.5 Interrupts The A/D converter generates an interrupt (ADI) at the end of A/D conversion. The ADI interrupt request can be enabled or disabled by the ADIE bit in ADCSR. Rev. 3.00 Mar 17, 2006 page 486 of 706 REJ09B0303-0300 Section 17 A/D Converter 17.6 Usage Notes The following points should be noted when using the A/D converter. Setting Range of Analog Power Supply and Other Pins 1. Analog input voltage range The voltage applied to the ANn analog input pins during A/D conversion should be in the range AVSS ≤ ANn ≤ AVCC (n = 0 to 7). 2. Relation between AVCC, AVSS and VCC, VSS As the relationship between AVCC, AVSS and VCC, VSS, set AVSS = VSS. If the A/D converter is not used, the AVCC and AVSS pins must on no account be left open. If conditions 1 and 2 above are not met, the reliability of the device may be adversely affected. Notes on Board Design: In board design, digital circuitry and analog circuitry should be as mutually isolated as possible, and layout in which digital circuit signal lines and analog circuit signal lines cross or are in close proximity should be avoided as far as possible. Failure to do so may result in incorrect operation of the analog circuitry due to inductance, adversely affecting A/D conversion values. Also, digital circuitry must be isolated from the analog input signals (AN0 to AN7), and analog power supply (AVCC) by the analog ground (AVSS). Also, the analog ground (AVSS) should be connected at one point to a stable digital ground (VSS) on the board. Notes on Noise Countermeasures: A protection circuit connected to prevent damage due to an abnormal voltage such as an excessive surge at the analog input pins (AN0 to AN7) should be connected between AVCC and AVSS as shown in figure 17.7. Also, the bypass capacitors connected to AVCC and the filter capacitor connected to AN0 to AN7 must be connected to AVSS. If a filter capacitor is connected as shown in figure 17.7, the input currents at the analog input pins (AN0 to AN7) are averaged, and so an error may arise. Also, when A/D conversion is performed frequently, as in scan mode, if the current charged and discharged by the capacitance of the sample-and-hold circuit in the A/D converter exceeds the current input via the input impedance (Rin), an error will arise in the analog input pin voltage. Careful consideration is therefore required when deciding the circuit constants. Rev. 3.00 Mar 17, 2006 page 487 of 706 REJ09B0303-0300 Section 17 A/D Converter AVCC 100 Ω Rin* 2 AN0 to AN7 *1 0.1 µF AVSS Notes: Figures are reference values. 1. 10 µF 0.01 µF 2. Rin: Input impedance Figure 17.7 Example of Analog Input Protection Circuit Table 17.5 Analog Pin Specifications Item Min Max Unit Analog input capacitance — 20 pF — 10* kΩ Permissible signal source impedance Note: * When VCC = 4.5 V to 5.5 V and φ ≤ 12 MHz 10 kΩ AN0 to AN7 To A/D converter 20 pF Note: Figures are reference values. Figure 17.8 Analog Input Pin Equivalent Circuit Rev. 3.00 Mar 17, 2006 page 488 of 706 REJ09B0303-0300 Section 17 A/D Converter A/D Conversion Precision Definitions: A/D conversion precision definitions for the H8/3577 Group and H8/3567 Group are given below. • Resolution The number of A/D converter digital output codes • Offset error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from the minimum voltage value B'0000000000 (H'000) to B'0000000001 (H'001) (see figure 17.10). • Full-scale error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from B'1111111110 (H'3FE) to B'111111111 (H'3FF) (see figure 17.10). • Quantization error The deviation inherent in the A/D converter, given by 1/2 LSB (see figure 17.9). • Nonlinearity error The error with respect to the ideal A/D conversion characteristic between the zero voltage and the full-scale voltage. Does not include the offset error, full-scale error, or quantization error. • Absolute precision The deviation between the digital value and the analog input value. Includes the offset error, full-scale error, quantization error, and nonlinearity error. Rev. 3.00 Mar 17, 2006 page 489 of 706 REJ09B0303-0300 Section 17 A/D Converter Digital output Ideal A/D conversion characteristic H'3FF H'3FE H'3FD H'004 H'003 H'002 Quantization error H'001 H'000 2 1 1024 1024 1022 1023 FS 1024 1024 Analog input voltage Figure 17.9 A/D Conversion Precision Definitions (1) Full-scale error Digital output Ideal A/D conversion characteristic Nonlinearity error Actual A/D conversion characteristic FS Offset error Analog input voltage Figure 17.10 A/D Conversion Precision Definitions (2) Rev. 3.00 Mar 17, 2006 page 490 of 706 REJ09B0303-0300 Section 17 A/D Converter Permissible Signal Source Impedance: Analog input is designed so that conversion precision is guaranteed for an input signal for which the signal source impedance is 10 kΩ (when AVCC = 4.5 to 5.5 V and φ ≤ 12 MHz, or when CSK = 0) or less. This specification is provided to enable the A/D converter’s sample-and-hold circuit input capacitance to be charged within the sampling time; if the sensor output impedance exceeds 10 kΩ (when AVCC = 4.5 to 5.5 V and φ ≤ 12 MHz, or when CSK = 0), charging may be insufficient and it may not be possible to guarantee the A/D conversion precision. However, if a large capacitance is provided externally, the input load will essentially comprise only the internal input resistance of 10 kΩ, and the signal source impedance is ignored. But since a low-pass filter effect is obtained in this case, it may not be possible to follow an analog signal with a large differential coefficient (e.g., 5 mV/µsec or greater). When converting a high-speed analog signal, a low-impedance buffer should be inserted. Influences on Absolute Precision: Adding capacitance results in coupling with GND, and therefore noise in GND may adversely affect absolute precision. Be sure to make the connection to an electrically stable GND such as AVSS. Care is also required to insure that filter circuits do not communicate with digital signals on the mounting board, so acting as antennas. Sensor output impedance, up to 10 kΩ H8/3577 Group or H8S/3567 Group chip A/D converter equivalent circuit 10 kΩ Sensor input Low-pass filter C to 0.1 µF Cin = 15 pF 20 pF Note: Figures are reference values. Figure 17.11 Example of Analog Input Circuit Rev. 3.00 Mar 17, 2006 page 491 of 706 REJ09B0303-0300 Section 17 A/D Converter Rev. 3.00 Mar 17, 2006 page 492 of 706 REJ09B0303-0300 Section 18 RAM Section 18 RAM 18.1 Overview The H8/3577 Group and H8/3567 Group have 2 kbytes of on-chip high-speed static RAM. The on-chip RAM is connected to the bus master by a 16-bit data bus, enabling both byte data and word data to be accessed in two states. This makes it possible to perform fast word data transfer. The on-chip RAM can be enabled or disabled by means of the RAM enable bit (RAME) in the system control register (SYSCR). 18.1.1 Block Diagram Figure 18.1 shows a block diagram of the on-chip RAM. Internal data bus (upper 8 bits) Internal data bus (lower 8 bits) H'E080 H'E081 H'E082 H'E083 H'E084 H'E085 H'EFFE H'EFFF H'FF00 H'FF01 H'FF7E H'FF7F Figure 18.1 Block Diagram of RAM Rev. 3.00 Mar 17, 2006 page 493 of 706 REJ09B0303-0300 Section 18 RAM 18.1.2 Register Configuration The on-chip RAM is controlled by SYSCR. Table 18.1 shows the register configuration. Table 18.1 Register Configuration Name Abbreviation R/W Initial Value Address System control register SYSCR R/W H'09 H'FFC4 18.2 System Control Register (SYSCR) Bit 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W The on-chip RAM is enabled or disabled by the RAME bit in SYSCR. For details of other bits in SYSCR, see section 3.2.2, System Control Register. Bit 0—RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is initialized when the reset state is released. It is not initialized in software standby mode. Bit 0 RAME Description 0 On-chip RAM is disabled 1 On-chip RAM is enabled 18.3 (Initial value) Operation When the RAME bit is set to 1, accesses to addresses H'E880 to H'EFFF and H'FF00 to H'FF7F are directed to the on-chip RAM. When the RAME bit is cleared to 0, the on-chip RAM is not accessed; a read will return an undefined value, and writes are invalid. Since the on-chip RAM is connected to the bus master by a 16-bit data bus, it can be written to and read in byte or word units. Each type of access is performed in two states. Even addresses use the upper 8 bits, and odd addresses use the lower 8 bits. Word data must start at an even address. Rev. 3.00 Mar 17, 2006 page 494 of 706 REJ09B0303-0300 Section 19 ROM Section 19 ROM 19.1 Overview The H8/3577, H8/3567, and H8/3567U have 56 kbytes of on-chip ROM (PROM or mask ROM), and the H8/3574, H8/3564, and H8/3564U have 32 kbytes. The ROM is connected to the bus master by a 16-bit data bus. The CPU accesses both byte and word data in two states, enabling faster instruction fetches and higher processing speed. Figure 19.1 shows a block diagram of the ROM. Internal data bus (upper 8 bits) Internal data bus (lower 8 bits) H'0000 H'0001 H'0002 H'0003 H'DFFE H'DFFF Figure 19.1 ROM Block Diagram (H8/3577, H8/3567, H8/3567U) 19.2 Operation The on-chip ROM is connected to the CPU by a 16-bit data bus, and both byte and word data is accessed in two states. Even addresses are connected to the upper 8 bits, and odd addresses to the lower 8 bits. Word data must start at an even address. Rev. 3.00 Mar 17, 2006 page 495 of 706 REJ09B0303-0300 Section 19 ROM 19.3 Writer Mode (H8/3577, H8/3567, H8/3567U) 19.3.1 Writer Mode Setup In writer mode the PROM versions of the H8/3577, H8/3567, and H8/3567U suspend the usual microcomputer functions to allow the on-chip PROM to be programmed. The programming method is the same as for the HN27C101. To select writer mode, apply the signal inputs listed in table 19.1. Table 19.1 Selection of Writer Mode Pin H8/3577 H8/3567, H8/3567U Input Mode pin MD1 Low Mode pin MD0 Low STBY pin Low Pins P63 and P64 High Mode pin TEST Low STBY pin Low Pins P47 and P52 High Rev. 3.00 Mar 17, 2006 page 496 of 706 REJ09B0303-0300 Section 19 ROM 19.3.2 Socket Adapter Pin Assignments and Memory Map The H8/3577, H8/3567, and H8/3567U can be programmed with a general-purpose PROM programmer by using a socket adapter to change the pin-out to 32 pins. See table 19.2. The same socket adapter can be used for H8/3577, H8/3567, and H8/3567U. Figures 19.2 to 19.4 show the socket adapter pin assignments. Table 19.2 Socket Adapter Package Socket Adapter 64-pin QFP (H8/3577) HS3297ESHS1H 64-pin shrink DIP (H8/3577) HS3297ESSS1H 44-pin QFP (H8/3567) TBD 42-pin shrink DIP (H8/3567) TBD 64-pin QFP (H8/3567U) TBD 64-pin shrink DIP (H8/3567U) TBD The PROM size is 56 kbytes for the H8/3577, H8/3567, and H8/3567U. Figure 19.5 shows memory maps of the H8/3577, H8/3567, and H8/3567U in writer mode. H'FF data should be specified for unused address areas in the on-chip PROM. When programming with a PROM programmer, limit the program address range to H'0000 to H'DFFF for the H8/3577, H8/3567, and H8/3567U. Specify H'FF data for addresses H'E000 and above. If these addresses are programmed by mistake, it may become impossible to program or verify the PROM data. The same problem may occur if an attempt is made to program the chip in page programming mode. Note that the PROM versions are one-time programmable (OTP) microcomputers, packaged in plastic packages, and cannot be reprogrammed. Rev. 3.00 Mar 17, 2006 page 497 of 706 REJ09B0303-0300 Section 19 ROM EPROM Socket H8/3577 DP-64S FP-64A Pin Pin HN27C101 (32 pins) 12 4 RES VPP 1 13 5 NMI EA 9 26 57 49 P3 0 EO0 13 58 50 P3 1 EO1 14 59 51 P3 2 EO2 15 60 52 P3 3 EO3 17 61 53 P3 4 EO4 18 62 54 P3 5 EO5 19 63 55 P3 6 EO6 20 64 56 P3 7 EO7 21 56 48 P1 0 EA 0 12 55 47 P1 1 EA 1 11 54 46 P1 2 EA 2 10 53 45 P1 3 EA 3 9 52 44 P1 4 EA 4 8 51 43 P1 5 EA 5 7 50 42 P1 6 EA 6 6 49 41 P1 7 EA 7 5 47 39 P2 0 EA 8 27 46 38 P2 1 OE 24 45 37 P2 2 EA10 23 44 36 P2 3 EA11 25 43 35 P2 4 EA12 4 42 34 P2 5 EA13 28 41 33 P2 6 EA14 29 40 32 P2 7 CE 22 1 57 P40 EA16 2 2 58 P41 EA15 3 3 59 P42 PGM 31 34 26 P6 3 VCC 32 35 27 P6 4 30 22 AVCC 14, 39 6, 31 VCC VSS 16 20 12 MD0 19 11 MD1 15 7 STBY 21 13 AVSS 16, 48 8, 40 VSS Note: All pins not listed in this figure should be left open. Legend: VPP: EO7 to EO0: EA16 to EA0: OE: CE: PGM: Programming power supply (12.5 V) Data input/output Address input Output enable Chip enable Program enable Figure 19.2 Socket Adapter Pin Assignments (H8/3577) Rev. 3.00 Mar 17, 2006 page 498 of 706 REJ09B0303-0300 Section 19 ROM EPROM Socket H8/3567 DP-42S FP-44A Pin Pin HN27C101 (32 pins) 7 2 RES VPP 1 8 3 NMI EA 9 26 21 16 P60 EO0 13 28 24 P61 EO1 14 27 23 P62 EO2 15 26 22 P63 EO3 17 22 18 P64 EO4 18 23 19 P65 EO5 19 24 20 P66 EO6 20 25 21 P67 EO7 21 37 33 P1 0 EA 0 12 36 32 P1 1 EA 1 11 35 31 P1 2 EA 2 10 34 30 P1 3 EA 3 9 33 29 P1 4 EA 4 8 31 27 P1 5 EA 5 7 30 26 P1 6 EA 6 6 29 25 P1 7 EA 7 5 40 36 P43 EA 8 27 41 37 P44 OE 24 42 38 P45 EA10 23 4 43 P46 EA11 25 16 11 P70 EA12 4 17 12 P71 EA13 28 18 13 P72 EA14 29 2 41 P41 CE 22 1 40 P40 EA16 2 19 14 P73 EA15 3 3 42 P42 PGM 31 5 44 P47 VCC 32 6 1 P52 20 15 AVCC 9, 10 4, 5 VCC VSS 16 14 9 TEST 11 6 STBY 15, 32 10, 28 VSS (/AVSS) Note: All pins not listed in this figure should be left open. Legend: VPP: EO7 to EO0: EA16 to EA0: OE: CE: PGM: Programming power supply (12.5 V) Data input/output Address input Output enable Chip enable Program enable Figure 19.3 Socket Adapter Pin Assignments (H8/3567) Rev. 3.00 Mar 17, 2006 page 499 of 706 REJ09B0303-0300 Section 19 ROM EPROM Socket H8/3567U DP-64S FP-64A Pin Pin HN27C101 (32 pins) 7 63 RES VPP 1 8 64 NMI EA 9 26 43 35 P60 EO0 13 50 42 P61 EO1 14 49 41 P62 EO2 15 48 40 P63 EO3 17 44 36 P64 EO4 18 45 37 P65 EO5 19 46 38 P66 EO6 20 47 39 P67 EO7 21 59 51 P1 0 EA 0 12 58 50 P1 1 EA 1 11 57 49 P1 2 EA 2 10 56 48 P1 3 EA 3 9 55 47 P1 4 EA 4 8 53 45 P1 5 EA 5 7 52 44 P1 6 EA 6 6 51 43 P1 7 EA 7 5 62 54 P43 EA 8 27 63 55 P44 OE 24 64 56 P45 EA10 23 4 60 P46 EA11 25 16 8 P70 EA12 4 17 9 P71 EA13 28 18 10 P72 EA14 29 2 58 P41 CE 22 1 57 P40 EA16 2 19 11 P73 EA15 3 3 59 P42 PGM 31 5 61 P47 VCC 32 6 62 P52 20 12 AVCC 21 13 DrVCC 9, 10 1, 2 VCC VSS 16 14 6 TEST 11 3 STBY 32 24 DrVSS 15, 54 7, 46 VSS (/AVSS) Note: All pins not listed in this figure should be left open. Legend: VPP: EO7 to EO0: EA16 to EA0: OE: CE: PGM: Programming power supply (12.5 V) Data input/output Address input Output enable Chip enable Program enable Figure 19.4 Socket Adapter Pin Assignments (H8/3567U) Rev. 3.00 Mar 17, 2006 page 500 of 706 REJ09B0303-0300 Section 19 ROM Address in MCU mode Address in writer mode H'0000 H'0000 On-chip PROM H'DFFF H'DFFF Undetermined value output* H'1FFFF Note: * If this address area is read in writer mode, the output data is not guaranteed. Figure 19.5 Memory Map in Writer Mode Rev. 3.00 Mar 17, 2006 page 501 of 706 REJ09B0303-0300 Section 19 ROM 19.4 PROM Programming The write, verify, and other sub-modes of the writer mode are selected as shown in table 19.3. Table 19.3 Selection of Sub-Modes in Writer Mode Sub-Mode CE OE PGM VPP VCC EO7 to EO0 EA16 to EA0 Write Low High Low VPP VCC Data input Address input Verify Low Low High VPP VCC Data output Address input Programming inhibited Low Low High High Low High Low High Low High Low High VPP VCC High impedance Address input The H8/3577, H8/3567, and H8/3567U PROM have the same standard read/write specifications as the HN27C101 EPROM. Page programming is not supported, however, so do not select page programming mode. PROM programmers that provide only page programming cannot be used. When selecting a PROM programmer, check that it supports a byte-at-a-time high-speed programming mode. Be sure to set the address range to H'0000 to H'DFFF for the H8/3577, H8/3567, and H8/3567U. 19.4.1 Programming and Verification An efficient, high-speed programming procedure can be used to program and verify PROM data. This procedure programs data quickly without subjecting the chip to voltage stress and without sacrificing data reliability. It leaves the data undefined in unused addresses. Figure 19.6 shows the basic high-speed programming flowchart. Tables 19.4 and 19.5 list the electrical characteristics of the chip in writer mode. Figure 19.7 shows a program/verify timing chart. Rev. 3.00 Mar 17, 2006 page 502 of 706 REJ09B0303-0300 Section 19 ROM Start Set program/verify mode VCC = 6.0 V ±0.25 V, VPP = 12.5 V ±0.3 V Address = 0 n=0 n + 1→ n Program tPW = 0.2 ms ±5% No Yes n < 25? No Address + 1 → address Verify OK? Yes Program tOPW = 0.2n ms Last address? No Yes Set read mode VCC = 5.0 V ±0.25 V, VPP = VCC Error No go Read all addresses Go End Figure 19.6 High-Speed Programming Flowchart Rev. 3.00 Mar 17, 2006 page 503 of 706 REJ09B0303-0300 Section 19 ROM Table 19.4 DC Characteristics When VCC = 6.0 V ±0.25 V, VPP = 12.5 V ±0.3 V, VSS = 0 V, Ta = 25°C ±5°C Item Symbol Min Typ Max Unit Test Conditions Input high voltage EO7–EO0, EA16–EA0, OE, CE, PGM VIH 2.4 — VCC + 0.3 V Input low voltage EO7–EO0, EA16–EA0, OE, CE, PGM VIL –0.3 — 0.8 V Output high voltage EO7–EO0 VOH 2.4 — — V IOH = –200 µA Output low voltage EO7–EO0 VOL — — 0.45 V IOL = 1.6 mA Input leakage EO7–EO0, current EA16–EA0, OE, CE, PGM |ILI| — — 2 µA Vin = 5.25 V/0.5 V VCC current ICC — — 40 mA VPP current IPP — — 40 mA Rev. 3.00 Mar 17, 2006 page 504 of 706 REJ09B0303-0300 Section 19 ROM Table 19.5 AC Characteristics When VCC = 6.0 V ±0.25 V, VPP = 12.5 V ±0.3 V, Ta = 25°C ±5°C Item Symbol Min Typ Max Unit Test Conditions Address setup time tAS 2 — — µs See figure 19.7* OE setup time tOES 2 — — µs Data setup time tDS 2 — — µs Address hold time tAH 0 — — µs Data hold time tDH 2 — — µs Data output disable time tDF — — 130 ns VPP setup time tVPS 2 — — µs Program pulse width tPW 0.19 0.20 0.21 ms OE pulse width for overwrite-programming tOPW 0.19 — 5.25 ms VCC setup time tVCS 2 — — µs CE setup time tCES 2 — — µs Data output delay time tOE 0 — 150 ns Note: * Input pulse level: 0.8 V to 2.2 V Input rise/fall time ≤ 20 ns Timing reference levels: input—1.0 V, 2.0 V; output—0.8 V, 2.0 V Rev. 3.00 Mar 17, 2006 page 505 of 706 REJ09B0303-0300 Section 19 ROM Write Verify Address tAH tAS Data Input data tDS VPP VCC Output data tDH tDF VPP VCC tVPS VCC + 1 VCC tVCS CE tCES PGM tPW OE tOES tOE tOPW Figure 19.7 PROM Program/Verify Timing Rev. 3.00 Mar 17, 2006 page 506 of 706 REJ09B0303-0300 Section 19 ROM 19.4.2 Notes on Programming (1) Program with the specified voltages and timing. The programming voltage (VPP) is 12.5 V. Caution: Applied voltages in excess of the specified values can permanently destroy the chip. Be particularly careful about the PROM programmer’s overshoot characteristics. If the PROM programmer is set to HN27C101 specifications, VPP will be 12.5 V. (2) Before writing data, check that the socket adapter and chip are correctly mounted in the PROM writer. Overcurrent damage to the chip can result if the index marks on the PROM programmer, socket adapter, and chip are not correctly aligned. (3) Don’t touch the socket adapter or chip while writing. Touching either of these can cause contact faults and write errors. (4) Page programming is not supported. Do not select page programming mode. (5) The PROM size is 56 kbytes. Set the address range to H'0000 to H'DFFF for the H8/3577, H8/3567, and H8/3567U. When programming, specify H'FF data for unused address areas (H'E000 to H'1FFFF). Rev. 3.00 Mar 17, 2006 page 507 of 706 REJ09B0303-0300 Section 19 ROM 19.4.3 Reliability of Programmed Data An effective way to assure the data holding characteristics of the programmed chips is to bake them at 150°C, then screen them for data errors. This procedure quickly eliminates chips with PROM memory cells prone to early failure. Figure 19.8 shows the recommended screening procedure. Write and verify program Bake with power off 125° to 150°C, 24 to 48Hr Read and check program Mount Figure 19.8 Recommended Screening Procedure If a group of write errors occurs while the same PROM programmer is in use, stop programming and check the PROM programmer and socket adapter for defects. Please inform Renesas Technology of any abnormal conditions noted during programming or in screening of program data after high-temperature baking. Rev. 3.00 Mar 17, 2006 page 508 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Section 20 Clock Pulse Generator 20.1 Overview The H8/3577 Group and H8/3567 Group have an on-chip clock pulse generator (CPG) that generates the system clock (φ), the bus master clock, and internal clocks. The clock pulse generator consists of an oscillator circuit, a duty adjustment circuit, clock selection circuit, medium-speed clock divider, bus master clock selection circuit. 20.1.1 Block Diagram Figure 20.1 shows a block diagram of the clock pulse generator. EXTAL Duty adjustment circuit Oscillator XTAL Medium-speed clock divider Clock selection circuit φ/2 to φ/32 Bus master clock selection circuit φ System clock To φ pin Internal clock To supporting modules Bus master clock To CPU, DTC Figure 20.1 Block Diagram of Clock Pulse Generator 20.1.2 Register Configuration The clock pulse generator is controlled by the standby control register (SBYCR). Table 20.1 shows the register configuration. Table 20.1 CPG Registers Name Abbreviation R/W Initial Value Address Standby control register SBYCR R/W H'00 H'FF84 Rev. 3.00 Mar 17, 2006 page 509 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator 20.2 Register Descriptions 20.2.1 Standby Control Register (SBYCR) Bit 7 6 5 4 3 2 1 0 SSBY STS2 STS1 STS0 — SCK2 SCK1 SCK0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W — R/W R/W R/W SBYCR is an 8-bit readable/writable register that performs power-down mode control. Only bits 0 to 2 are described here. For a description of the other bits, see section 21.2.1, Standby Control Register (SBYCR). SBYCR is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 2 to 0—System Clock Select 2 to 0 (SCK2 to SCK0): These bits select the bus master clock for high-speed mode and medium-speed mode. Bit 2 Bit 1 Bit 0 SCK2 SCK1 SCK0 Description 0 0 0 Bus master is in high-speed mode 1 Medium-speed clock is φ/2 0 Medium-speed clock is φ/4 1 Medium-speed clock is φ/8 0 0 Medium-speed clock is φ/16 1 Medium-speed clock is φ/32 1 — — 1 1 Rev. 3.00 Mar 17, 2006 page 510 of 706 REJ09B0303-0300 (Initial value) Section 20 Clock Pulse Generator 20.3 Oscillator Clock pulses can be supplied by connecting a crystal resonator, or by input of an external clock. 20.3.1 Connecting a Crystal Resonator Circuit Configuration: A crystal resonator can be connected as shown in the example in figure 20.2. Select the damping resistance Rd according to table 20.2. An AT-cut parallel-resonance crystal should be used. CL1 EXTAL XTAL Rd CL2 CL1 = CL2 = 10 to 22 pF Figure 20.2 Connection of Crystal Resonator (Example) Table 20.2 Damping Resistance Value Frequency (MHz) 2 4 8 10 12 16 20 Rd (Ω) 1k 500 200 0 0 0 0 Crystal resonator: Figure 20.3 shows the equivalent circuit of the crystal resonator. Use a crystal resonator that has the characteristics shown in table 20.3 and the same frequency as the system clock (φ). CL L Rs XTAL EXTAL C0 AT-cut parallel-resonance type Figure 20.3 Crystal Resonator Equivalent Circuit Rev. 3.00 Mar 17, 2006 page 511 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Table 20.3 Crystal Resonator Parameters Frequency (MHz) 2 4 8 10 12 16 20 RS max (Ω) 500 120 80 70 60 50 40 C0 max (pF) 7 7 7 7 7 7 7 Note on Board Design: When a crystal resonator is connected, the following points should be noted. Other signal lines should be routed away from the oscillator circuit to prevent induction from interfering with correct oscillation. See figure 20.4. When designing the board, place the crystal resonator and its load capacitors as close as possible to the XTAL and EXTAL pins. Avoid Signal A Signal B CL2 H8/3577 Group or H8/3567 Group chip XTAL EXTAL CL1 Figure 20.4 Example of Incorrect Board Design Rev. 3.00 Mar 17, 2006 page 512 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator 20.3.2 External Clock Input Circuit Configuration: An external clock signal can be input as shown in the examples in figure 20.5. If the XTAL pin is left open, make sure that stray capacitance is no more than 10 pF. In example (b), make sure that the external clock is held high in standby mode. EXTAL XTAL External clock input Open (a) XTAL pin left open EXTAL External clock input XTAL (b) Complementary clock input at XTAL pin Figure 20.5 External Clock Input (Examples) External Clock: The external clock signal should have the same frequency as the system clock (φ). Table 20.4 and figure 20.6 show the input conditions for the external clock. Rev. 3.00 Mar 17, 2006 page 513 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Table 20.4 External Clock Input Conditions VCC = 5.0 V ±10% Item Symbol Min Max Unit Test Conditions External clock input low pulse width tEXL 20 — ns Figure 20.6 External clock input high pulse width tEXH 20 — ns External clock rise time tEXr — 5 ns External clock fall time tEXf — 5 ns Clock low pulse width tCL 0.4 0.6 tcyc φ ≥ 5 MHz 80 — ns φ < 5 MHz 0.4 0.6 tcyc φ ≥ 5 MHz 80 — ns φ < 5 MHz Clock high pulse width tCH tEXH Figure 22.4 tEXL VCC × 0.5 EXTAL tEXr tEXf Figure 20.6 External Clock Input Timing Table 20.5 shows the external clock output settling delay time, and figure 20.7 shows the external clock output settling delay timing. The oscillator and duty adjustment circuit have a function for adjusting the waveform of the external clock input at the EXTAL pin. When the prescribed clock signal is input at the EXTAL pin, internal clock signal output is fixed after the elapse of the external clock output settling delay time (tDEXT). As the clock signal output is not fixed during the tDEXT period, the reset signal should be driven low to maintain the reset state. Rev. 3.00 Mar 17, 2006 page 514 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Table 20.5 External Clock Output Settling Delay Time Conditions: VCC = 4.5 V to 5.5 V, AVCC = 4.5 V to 5.5 V, VSS = AVSS = 0 V Item External clock output settling delay time Note: * VCC STBY Symbol Min Max Unit Notes * 500 — µs Figure 20.7 tDEXT tDEXT includes a 10tcyc RES pulse width (tRESW). 4.5 V VIH EXTAL φ (internal or external) RES tDEXT* Note: * tDEXT includes a RES pulse width (tRESW). Figure 20.7 External Clock Output Settling Delay Timing Rev. 3.00 Mar 17, 2006 page 515 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator 20.4 Duty Adjustment Circuit When the oscillator frequency is 5 MHz or higher, the duty adjustment circuit adjusts the duty cycle of the clock signal from the oscillator to generate the system clock (φ). 20.5 Medium-Speed Clock Divider The medium-speed clock divider divides the system clock to generate φ/2, φ/4, φ/8, φ/16, and φ/32 clocks. 20.6 Bus Master Clock Selection Circuit The bus master clock selection circuit selects the system clock (φ) or one of the medium-speed clocks (φ/2, φ/4, φ/8, φ/16, or φ/32) to be supplied to the bus master, according to the settings of bits SCK2 to SCK0 in SBYCR. 20.7 Universal Clock Pulse Generator [H8/3567 Group Version with On-Chip USB] The H8/3567 Group version with an on-chip USB has a USB clock pulse generator (UCPG) that generates the 48 MHz USB clock (CLK48) from an 8, 12, 16, or 20 MHz input clock. The input clock can be selected from (1) the 12 MHz crystal oscillator or (2) the system clock (only when the system clock is 8, 12, 16, or 20 MHz). The USB clock pulse generator consists of an oscillator, clock selection circuit, and frequency division/multiplication circuit. 20.7.1 Block Diagram Figure 20.8 shows a block diagram of the USB clock pulse generator. EXTAL12 Oscillator XTAL12 φ (system clock) 12 MHz Clock selection circuit frequency 48 MHz division/ multiplication circuit Figure 20.8 Block Diagram of USB Clock Pulse Generator Rev. 3.00 Mar 17, 2006 page 516 of 706 REJ09B0303-0300 To USB Section 20 Clock Pulse Generator 20.7.2 Registers Table 20.6 USB Clock Pulse Generator Registers Name Abbreviation R/W Initial Value Address USB control/status register 0 USBCSR0 R/W H'00 H'FDF5 USB control register USBCR R/W H'7F H'FDFD USB PLL control register UPLLCR R/W H'01 H'FDFE USB Control/Status Register 0 (USBCSR0) Bit 7 6 5 4 3 DP5CNCT DP4CNCT DP3CNCT DP2CNCT EP0STOP 2 1 0 EPIVLD EP0OTC CKSTOP Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/W R/W R/W R/W USBCSR0 contains flags (DPCNCT) that indicate the USB hubs’ downstream port connection status, and bits that control the operation of the USB function. Only bit 0 is described here. For details of the other bits, see section 7.2.11, USB Control/Status Register 0 (USBCSR0). USBCSR0 is initialized to H'00 by a system reset, and bits 3 to 0 are also cleared to 0 by a function soft reset. Bit 0—Clock Stop (CKSTOP): Controls the USB function operating clock. When the USB function is placed in the suspend state due to a bus idle condition, this bit should be set to 1 after the necessary processing is completed. The clock supply to the USB function is then stopped, reducing power consumption. When the CKSTOP bit is set to 1, writes to USB module registers are invalid. If these registers are read, the contents of the read data are not guaranteed, but there are no read-related status changes (such as decrementing of FVSR). If a bus idle condition of the specified duration or longer is detected, the suspend IN interrupt flag is set, and when a change in the bus status is subsequently detected the suspend OUT interrupt flag is set. When the suspend OUT interrupt flag is set, the CKSTOP bit is simultaneously cleared to 0. Rev. 3.00 Mar 17, 2006 page 517 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Bit 0 CKSTOP Description 0 Clock is supplied to USB function (Initial value) [Clearing conditions] 1 • System reset • Function soft reset • Suspend OUT interrupt flag setting Clock supply to USB function is stopped [Setting condition] When 1 is written to CKSTOP after reading CKSTOP = 0 in the function suspend state. USB Control Register (USBCR) Bit 7 6 5 4 3 2 1 0 FADSEL FONLY Initial value 0 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W FNCSTP UIFRST HPLLRST HSRST FPLLRST FSRST USBCR contains bits (FADSEL, FONLY, FNCSTP) that control USB function and USB hub internal connection, and reset control bits for sequential enabling of the operation of each part according to the procedure in USB module initialization. Only bits 3 and 1 are described here. For details of the other bits, see section 7.2.18, USB Control Register (USBCR). USBCR is initialized to H'7F by a system reset [in an H8/3567 reset (by RES input or the watchdog timer), and in hardware standby mode]. It is not initialized in software standby mode. Bit 3—Hub Block PLL Soft Reset (HPLLRST): Resets the USB bus clock synchronization circuit (DPLL) in the hub. When HPLLRST is set to 1, the DPLL circuit in the USB hub block is reset, and bus clock synchronous operation halts. HPLLRST is cleared to 0 after PLL operation stabilizes. Rev. 3.00 Mar 17, 2006 page 518 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator Bit 3 HPLLRST Description 0 USB hub block DPLL is placed in operational state 1 USB hub block DPLL is placed in reset state (Initial value) Bit 1—Function Block PLL Soft Reset (FPLLRST): Resets the USB bus clock synchronization circuit (DPLL) in the USB function block. When FPLLRST is set to 1, the DPLL circuit in the USB function block is reset, and bus clock synchronous operation halts. FPLLRST is cleared to 0 after PLL operation stabilizes. Bit 1 FPLLRST Description 0 USB function block DPLL is placed in operational state 1 USB function block DPLL is placed in reset state (Initial value) USB PLL Control Register (UPLLCR) Bit 7 6 5 — — — 4 3 2 1 Initial value 0 0 0 0 0 0 0 1 Read/Write R R R R/W R/W R/W R/W R/W CKSEL2 CKSEL1 CKSEL0 PFSEL1 0 PFSEL0 UPLLCR contains bits that control the method of generating the USB function and USB hub operating clock. UPLLCR is initialized to H'01 by a system reset [in an H8/3567 reset (by RES input or the watchdog timer), and in hardware standby mode]. It is not initialized in software standby mode. Bits 4 to 2—Clock Source Select 2 to 0 (CKSEL2 to CKSEL0): These bits select the source of the clock supplied to the USB operating clock generator (PLL). CKSEL0 selects either the USB clock pulse generator (XTAL12) or the system clock pulse generator (XTATL) as the clock source. The USB clock pulse generator starts operating when it is selected as a clock source. It operates with CKSEL2 = 1, CKSEL0 = 1. When CKSEL2 = 1 and CKSEL1 = 1, the PLL operates. Rev. 3.00 Mar 17, 2006 page 519 of 706 REJ09B0303-0300 Section 20 Clock Pulse Generator When CKSEL1 is cleared to 0, a clock is not input to the PLL, and PLL operation halts. The 48 MHz signal from the USB clock pulse generator can be input directly as the USB operating clock. When CKSEL2 is cleared to 0, a clock is not input to the PLL, and PLL operation halts. Bit 4 Bit 3 Bit 2 CKSEL2 CKSEL1 CKSEL0 0 1 Description 0 0 PLL operation halted, clock input halted — — PLL operation halted, clock input halted 0 0 Setting prohibited 1 PLL operation halted (Initial value) USB clock pulse generator (XTAL12: 48 MHz) used directly instead of PLL output 1 0 PLL operates with system clock pulse generator (XTAL) as clock source 1 PLL operates with USB clock pulse generator (XTAL12) as clock source Bits 1 and 0—PLL Frequency Select 1 and 0 (PFSEL1, PFSEL0): These bits select the frequency of the clock supplied to the USB operating clock generator (PLL). The PLL generates the 48 MHz USB operating clock using the frequency selected with these bits as the clock source frequency. Bit 1 Bit 0 PFSEL1 PFSEL0 Description 0 0 PLL input clock is 8 MHz 1 PLL input clock is 12 MHz 0 PLL input clock is 16 MHz 1 PLL input clock is 20 MHz 1 Rev. 3.00 Mar 17, 2006 page 520 of 706 REJ09B0303-0300 (Initial value) Section 21 Power-Down State Section 21 Power-Down State 21.1 Overview In addition to the normal program execution state, the H8/3577 Group and H8/3567 Group have a power-down state in which operation of the CPU and oscillator is halted and power dissipation is reduced. Low-power operation can be achieved by individually controlling the CPU, on-chip supporting modules, and so on. The operating modes are as follows: 1. High-speed mode 2. Medium-speed mode 3. Sleep mode 4. Module stop mode 5. Software standby mode 6. Hardware standby mode Of these, 2 to 6 are power-down modes. Sleep mode is a CPU mode, medium-speed mode is a CPU operating clock state, and module stop mode is an on-chip supporting module mode. Certain combinations of these modes can be set. After a reset, the MCU is in high-speed mode and module stop mode. Table 21.1 shows the internal chip states in each mode, and table 21.2 shows the conditions for transition to the various modes. Figure 21.1 shows a mode transition diagram. Rev. 3.00 Mar 17, 2006 page 521 of 706 REJ09B0303-0300 Section 21 Power-Down State Table 21.1 H8/3577 Group and H8/3567 Group Internal States in Each Mode Function HighSpeed MediumSpeed Sleep Module Stop Software Standby Hardware Standby System clock oscillator Functioning Functioning Functioning Functioning Halted Halted CPU operation Instructions Functioning Mediumspeed Halted Functioning Halted Halted Registers Functioning Mediumspeed Retained Functioning Retained Undefined NMI Functioning Functioning Functioning Functioning Functioning Halted WDT0 Functioning Functioning Functioning Functioning Halted (retained) Halted (reset) TMR0, TMR1 Functioning Functioning Functioning Functioning/ Halted (retained) halted (retained) Halted (reset) Functioning Functioning Functioning Functioning/ Halted (reset) halted (reset) Halted (reset) External interrupts IRQ0 IRQ1 IRQ2 On-chip supporting module operation FRT TMRX, Y Timer connection IIC0 IIC1 SCI0 PWM PWMX A/D RAM Functioning Functioning Functioning Functioning Retained Retained I/O Functioning Functioning Functioning Functioning Retained High impedance USB Functioning Functioning Functioning Functioning/ Functioning/ Halted halted* halted* (reset) Note: “Halted (retained)” means that internal register values are retained. The internal state is “operation suspended.” “Halted (reset)” means that internal register values and internal states are initialized. In module stop mode, only modules for which a stop setting has been made are halted (reset or retained). * Functioning (USB hub part only) when the USB clock (XTAL12, EXTAL12) is selected as a USB operating clock, and halted (retained) when not selected. Rev. 3.00 Mar 17, 2006 page 522 of 706 REJ09B0303-0300 Section 21 Power-Down State Program-halted state STBY pin = low Reset state STBY pin = high RES pin = low Hardware standby mode RES pin = high Program execution state SSBY = 0 SLEEP instruction Sleep mode High-speed mode Any interrupt SCK2 to SCK0 ≠ 0 SCK2 to SCK0 = 0 Medium-speed mode SLEEP instruction External interrupt* : Transition after exception handling SSBY = 1 Software standby mode : Power-down mode Notes: When a transition is made between modes by means of an interrupt, transition cannot be made on interrupt source generation alone. Ensure that interrupt handling is performed after accepting the interrupt request. From any state except hardware standby mode, a transition to the reset state occurs whenever RES goes low. From any state, a transition to hardware standby mode occurs when STBY goes low. * NMI, IRQ0 to IRQ2 Figure 21.1 Mode Transitions Table 21.2 Power-Down Mode Transition Conditions State before Transition High-speed/ medium-speed Control Bit States at Time of Transition SSBY State after Transition by SLEEP Instruction State after Return by Interrupt 0 Sleep High-speed/ medium-speed 1 Software standby High-speed/ medium-speed Rev. 3.00 Mar 17, 2006 page 523 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.1.1 Register Configuration The power-down state is controlled by the SBYCR and MSTPCR registers. Table 21.3 summarizes these registers. Table 21.3 Power-Down State Registers Name Abbreviation R/W Initial Value Address Standby control register SBYCR R/W H'00 H'FF84 Module stop control register MSTPCRH R/W H'3F H'FF86 MSTPCRL R/W H'FF H'FF87 21.2 Register Descriptions 21.2.1 Standby Control Register (SBYCR) Bit 7 6 5 4 3 2 1 0 SSBY STS2 STS1 STS0 — SCK2 SCK1 SCK0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W — R/W R/W R/W SBYCR is an 8-bit readable/writable register that performs power-down mode control. SBYCR is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bit 7—Software Standby (SSBY): Determines the operating mode, in combination with other control bits, when a power-down mode transition is made by executing a SLEEP instruction. The SSBY setting is not changed by a mode transition due to an interrupt, etc. Bit 7 SSBY Description 0 Transition to sleep mode after execution of SLEEP instruction in high-speed mode or medium-speed mode (Initial value) 1 Transition to software standby mode, after execution of SLEEP instruction in highspeed mode or medium-speed mode Rev. 3.00 Mar 17, 2006 page 524 of 706 REJ09B0303-0300 Section 21 Power-Down State Bits 6 to 4—Standby Timer Select 2 to 0 (STS2 to STS0): These bits select the time the MCU waits for the clock to stabilize when software standby mode is cleared and a transition is made to high-speed mode or medium-speed mode by means of a specific interrupt or instruction. With crystal oscillation, refer to table 21.4 and make a selection according to the operating frequency so that the standby time is at least 8 ms (the oscillation settling time). With an external clock, any selection can be made. Bit 6 Bit 5 Bit 4 STS2 STS1 STS0 Description 0 0 0 Standby time = 8192 states 1 Standby time = 16384 states 0 Standby time = 32768 states 1 Standby time = 65536 states 0 Standby time = 131072 states 1 Standby time = 262144 states 0 Reserved 1 Standby time = 16 states 1 1 0 1 (Initial value) Bit 3—Reserved: This bit cannot be modified and is always read as 0. Bits 2 to 0—System Clock Select (SCK2 to SCK0): These bits select the clock for the bus master in high-speed mode and medium-speed mode. Bit 2 Bit 1 Bit 0 SCK2 SCK1 SCK0 Description 0 0 0 Bus master is in high-speed mode 1 Medium-speed clock is φ/2 0 Medium-speed clock is φ/4 1 Medium-speed clock is φ/8 0 Medium-speed clock is φ/16 1 Medium-speed clock is φ/32 — — 1 1 0 1 (Initial value) Rev. 3.00 Mar 17, 2006 page 525 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.2.2 Module Stop Control Register (MSTPCR) MSTPCRH Bit 7 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP MSTP 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value Read/Write 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W MSTPCR comprises two 8-bit readable/writable registers that perform module stop mode control. MSTPCR is initialized to H'3FFF by a reset and in hardware standby mode. It is not initialized in software standby mode. MSTRCRH and MSTPCRL Bits 7 to 0—Module Stop (MSTP 15 to MSTP 0): These bits specify module stop mode. See table 21.3 for the method of selecting on-chip supporting modules. MSTPCRH, MSTPCRL Bits 7 to 0 MSTP15 to MSTP0 Description 0 Module stop mode is cleared (Initial value of MSTP15, MSTP14) 1 Module stop mode is set (Initial value of MSTP13 to MSTP0) 21.3 Medium-Speed Mode When the SCK2 to SCK0 bits in SBYCR are set to 1 in high-speed mode, the operating mode changes to medium-speed mode at the end of the bus cycle. In medium-speed mode, the CPU operates on the operating clock (φ/2, φ/4, φ/8, φ/16, or φ/32) specified by the SCK2 to SCK0 bits. On-chip supporting modules other than the bus masters always operate on the high-speed clock (φ). In medium-speed mode, a bus access is executed in the specified number of states with respect to the bus master operating clock. For example, if φ/4 is selected as the operating clock, on-chip memory is accessed in 8 states, and internal I/O registers in 12 states. Medium-speed mode is cleared by clearing all of bits SCK2 to SCK0 to 0. A transition is made to high-speed mode and medium-speed mode is cleared at the end of the current bus cycle. Rev. 3.00 Mar 17, 2006 page 526 of 706 REJ09B0303-0300 Section 21 Power-Down State If a SLEEP instruction is executed when the SSBY bit in SBYCR is cleared to 0, a transition is made to sleep mode. When sleep mode is cleared by an interrupt, medium-speed mode is restored. If a SLEEP instruction is executed when the SSBY bit in SBYCR is set to 1, a transition is made to software standby mode. When software standby mode is cleared by an external interrupt, medium-speed mode is restored. When the RES pin is driven low, a transition is made to the reset state, and medium-speed mode is cleared. The same applies in the case of a reset caused by overflow of the watchdog timer. When the STBY pin is driven low, a transition is made to hardware standby mode. Figure 21.2 shows the timing for transition to and clearance of medium-speed mode. Medium-speed mode φ, supporting module clock Bus master clock Internal address bus SBYCR SBYCR Internal write signal Figure 21.2 Medium-Speed Mode Transition and Clearance Timing Rev. 3.00 Mar 17, 2006 page 527 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.4 Sleep Mode 21.4.1 Sleep Mode If a SLEEP instruction is executed when the SSBY bit in SBYCR is cleared to 0, the CPU enters sleep mode. In sleep mode, CPU operation stops but the contents of the CPU’s internal registers are retained. Other supporting modules do not stop. 21.4.2 Clearing Sleep Mode Sleep mode is cleared by any interrupt, or with the RES pin or STBY pin. Clearing with an Interrupt: When an interrupt request signal is input, sleep mode is cleared and interrupt exception handling is started. Sleep mode will not be cleared if interrupts are disabled, or if interrupts other than NMI have been masked by the CPU. Clearing with the RES Pin: When the RES pin is driven low, the reset state is entered. When the RES pin is driven high after the prescribed reset input period, the CPU begins reset exception handling. Clearing with the STBY Pin: When the STBY pin is driven low, a transition is made to hardware standby mode. 21.5 Module Stop Mode 21.5.1 Module Stop Mode Module stop mode can be set for individual on-chip supporting modules. When the corresponding MSTP bit in MSTPCR is set to 1, module operation stops at the end of the bus cycle and a transition is made to module stop mode. The CPU continues operating independently. Table 21.4 shows MSTP bits and the corresponding on-chip supporting modules. When the corresponding MSTP bit is cleared to 0, module stop mode is cleared and the module starts operating again at the end of the bus cycle. In module stop mode, the internal states of modules other than the SCI, A/D converter, 8-bit PWM module, and 14-bit PWM module, are retained. Additionally, when the USB clock (XTAL12, EXTAL12) is selected as a USB operating clock, the USB module does not stop operating even when the MSTP1 bit is set to 1. To stop the Rev. 3.00 Mar 17, 2006 page 528 of 706 REJ09B0303-0300 Section 21 Power-Down State USB module, initialize UPLLCR to H'01 before setting the MSTP1 bit to 1. Also, it is recommended to initialize USBCR to H'7F to prepare for cancellation of the module stop state. After reset release, all modules other than the DTC are in module stop mode. When an on-chip supporting module is in module stop mode, read/write access to its registers is disabled. Table 21.4 MSTP Bits and Corresponding On-Chip Supporting Modules Register Bit MSTPCRH MSTP15* — MSTP14* — MSTPCRL Note: 21.5.2 * Module MSTP13 16-bit free-running timer (FRT) MSTP12 8-bit timers (TMR0, TMR1) MSTP11 8-bit PWM timer (PWM), 14-bit PWM timer (PWMX) MSTP10* — MSTP9 A/D converter MSTP8 8-bit timers (TMRX, TMRY), timer connection MSTP7 MSTP6* Serial communication interface 0 (SCI0) — MSTP5* — MSTP4 I C bus interface (IIC) channel 0 MSTP3 I C bus interface (IIC) channel 1 MSTP2* — MSTP1 MSTP0* — 2 2 Universal serial bus interface (USB) Bits 15, 14, 10, 6, 5, 2, and 0 can be read or written to, must be set to 1. Usage Note The MSTP bit for modules not included on-chip must be set to 1. Rev. 3.00 Mar 17, 2006 page 529 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.6 Software Standby Mode 21.6.1 Software Standby Mode If a SLEEP instruction is executed when the SSBY bit in SBYCR is set to 1, software standby mode is entered. In this mode, the CPU, on-chip supporting modules, and oscillator all stop. However, the contents of the CPU’s internal registers, RAM data, and the states of on-chip supporting modules other than the SCI, PWM, and PWMX, and of the I/O ports, are retained.* In this mode the oscillator stops, and therefore power dissipation is significantly reduced. Note: * When the USB clock (XTAL12, EXTAL12) is selected as a USB operating clock, the USB module does not stop operating even under the software standby mode. To realize the power save state, initialize UPLLCR to H'01 and USBCR to H'7F. 21.6.2 Clearing Software Standby Mode Software standby mode is cleared by an external interrupt (NMI pin, or pin IRQ0, IRQ1, or IRQ2), or by means of the RES pin or STBY pin. Clearing with an Interrupt: When an NMI, IRQ0, IRQ1, or IRQ2 interrupt request signal is input, clock oscillation starts, and after the elapse of the time set in bits STS2 to STS0 in SYSCR, stable clocks are supplied to the entire chip, software standby mode is cleared, and interrupt exception handling is started. Software standby mode cannot be cleared with an IRQ0, IRQ1, or IRQ2 interrupt if the corresponding enable bit has been cleared to 0 or has been masked by the CPU. Clearing with the RES Pin: When the RES pin is driven low, clock oscillation is started. At the same time as clock oscillation starts, clocks are supplied to the entire chip. Note that the RES pin must be held low until clock oscillation stabilizes. When the RES pin goes high, the CPU begins reset exception handling. Clearing with the STBY Pin: When the STBY pin is driven low, a transition is made to hardware standby mode. Rev. 3.00 Mar 17, 2006 page 530 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.6.3 Setting Oscillation Settling Time after Clearing Software Standby Mode Bits STS2 to STS0 in SBYCR should be set as described below. Using a Crystal Oscillator: Set bits STS2 to STS0 so that the standby time is at least 8 ms (the oscillation settling time). Table 21.5 shows the standby times for different operating frequencies and settings of bits STS2 to STS0. Table 21.5 Oscillation Settling Time Settings 20 STS2 STS1 STS0 Standby Time MHz 16 MHz 12 MHz 10 MHz 8 MHz 6 MHz 4 MHz 2 MHz Unit 0 4.1 ms 0 0 8192 states 0.41 0.51 0.65 0.8 1.0 1.3 2.0 1 16384 states 0.82 1.0 1.3 1.6 2.0 2.7 4.1 0 32768 states 1.6 2.0 2.7 3.3 4.1 5.5 1 65536 states 3.3 4.1 5.5 6.6 0 0 131072 states 6.6 8.2 10.9 13.1 16.4 1 262144 states 13.1 16.4 21.8 26.2 32.8 43.6 65.6 131.2 1 0 Reserved — — — — — — — — 1 16 states 0.8 1.0 1.3 1.6 2.0 2.7 4.0 8.0 1 1 8.2 8.2 16.4 10.9 16.4 32.8 21.8 65.5 8.2 32.8 µs Legend: : Recommended time setting —: Don’t care Using an External Clock: Any value can be set. Normally, use of the minimum time is recommended. 21.6.4 Software Standby Mode Application Example Figure 21.3 shows an example in which a transition is made to software standby mode at the falling edge on the NMI pin, and software standby mode is cleared at the rising edge on the NMI pin. In this example, an NMI interrupt is accepted with the NMIEG bit in SYSCR cleared to 0 (falling edge specification), then the NMIEG bit is set to 1 (rising edge specification), the SSBY bit is set to 1, and a SLEEP instruction is executed, causing a transition to software standby mode. Software standby mode is then cleared at the rising edge on the NMI pin. Rev. 3.00 Mar 17, 2006 page 531 of 706 REJ09B0303-0300 Section 21 Power-Down State Oscillator φ NMI NMIEG SSBY NMI exception handling NMIEG = 1 SSBY = 1 Software standby mode (power-down state) Oscillation settling time tOSC2 NMI exception handling SLEEP instruction Figure 21.3 Software Standby Mode Application Example 21.6.5 Usage Note In software standby mode, I/O port states are retained. Therefore, there is no reduction in current dissipation for the output current when a high-level signal is output. Current dissipation increases while waiting for oscillation to settle. Rev. 3.00 Mar 17, 2006 page 532 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.7 Hardware Standby Mode 21.7.1 Hardware Standby Mode When the STBY pin is driven low, a transition is made to hardware standby mode from any mode. In hardware standby mode, all functions enter the reset state and stop operation, resulting in a significant reduction in power dissipation. As long as the prescribed voltage is supplied, on-chip RAM data is retained. I/O ports are set to the high-impedance state. In order to retain on-chip RAM data, the RAME bit in SYSCR should be cleared to 0 before driving the STBY pin low. Do not change the state of the mode pins (MD1 and MD0, TEST) while the chip is in hardware standby mode. Hardware standby mode is cleared by means of the STBY pin and the RES pin. When the STBY pin is driven high while the RES pin is low, the reset state is set and clock oscillation is started. Ensure that the RES pin is held low until the clock oscillation settles (at least 8 ms—the oscillation settling time—when using a crystal oscillator). When the RES pin is subsequently driven high, a transition is made to the program execution state via the reset exception handling state. Rev. 3.00 Mar 17, 2006 page 533 of 706 REJ09B0303-0300 Section 21 Power-Down State 21.7.2 Hardware Standby Mode Timing Figure 21.4 shows an example of hardware standby mode timing. When the STBY pin is driven low after the RES pin has been driven low, a transition is made to hardware standby mode. Hardware standby mode is cleared by driving the STBY pin high, waiting for the oscillation settling time, then changing the RES pin from low to high. Oscillator RES STBY Oscillation settling time Figure 21.4 Hardware Standby Mode Timing Rev. 3.00 Mar 17, 2006 page 534 of 706 REJ09B0303-0300 Reset exception handling Section 22 Electrical Characteristics Section 22 Electrical Characteristics 22.1 Absolute Maximum Ratings Table 22.1 lists the absolute maximum ratings. Table 22.1 Absolute Maximum Ratings Item Symbol Value Unit Power supply voltage VCC –0.3 to +7.0 V Program voltage VPP –0.3 to +13.5 V Bus driver power supply voltage (H8/3567U Group only) DrVCC –0.3 to +4.3 V Input voltage (except port 7) Vin –0.3 to VCC + 0.3 V Input voltage (port 7) Vin –0.3 to AVCC + 0.3 V Analog power supply voltage AVCC –0.3 to +7.0 V Analog input voltage VAN –0.3 to AVCC + 0.3 V Operating temperature Topr –20 to +75 °C Storage temperature Tstg –55 to +125 °C Caution: Permanent damage to the chip may result if absolute maximum ratings are exceeded. Rev. 3.00 Mar 17, 2006 page 535 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.2 DC Characteristics Table 22.2 lists the DC characteristics. Table 22.3 lists the permissible output currents. Table 22.2 DC Characteristics 1 1 Conditions: VCC = 5.0 V ±10%, AVCC* = 5.0 V ±10%, VSS = AVSS* = 0 V, Ta = –20 to +75°C Item Symbol Min Typ Max Unit Test Conditions 1.0 — — V — — VCC × 0.7 V VT – VT 0.4 — — V VIH VCC – 0.7 — VCC + 0.3 V EXTAL VCC × 0.7 — VCC + 0.3 V Port 7 2.0 — AVCC + 0.3 V Input pins except (1) and (2) above 2.0 — VCC + 0.3 V –0.3 — 0.5 V –0.3 — 0.8 V VCC – 0.5 — — V IOH = –200 µA 3.5 — — V IOH = –1 mA 2.0 — — V IOH = –200 µA Schmitt P67 to P60* , 3 trigger input IRQ2 to IRQ0* voltage 2 Input high voltage RES, STBY, 7 NMI, MD1* , 7 8 MD * , TEST* (1) – VT + VT + (2) – 0 Input low voltage RES, STBY, 7 7 MD1* , MD0* , 8 TEST* (3) VIL NMI, EXTAL, input pins except (1) and (3) above Output All output pins high voltage (except P47, and P52) 4 P4 , P5 * VOH Output low voltage All output pins VOL — — 0.4 V IOL = 1.6 mA Input leakage current RES Iin — — 10.0 µA Vin = 0.5 to VCC – 0.5 V — — 1.0 µA — — 1.0 µA 7 2 7 STBY, NMI, MD1* , 7 8 MD0* , TEST* Port 7 Rev. 3.00 Mar 17, 2006 page 536 of 706 REJ09B0303-0300 Vin = 0.5 to AVCC – 0.5 V Section 22 Electrical Characteristics Item Symbol Min Typ Max Unit Test Conditions Three-state Ports 1 to 6 leakage current (off state) 7 Input Ports 1 to 3* pull-up MOS current ITSI — — 1.0 µA Vin = 0.5 to VCC – 0.5 V –IP 30 — 300 µA Vin = 0 V Cin — — 80 pF Vin = 0 V f = 1 MHz Ta = 25°C Input RES capacitance NMI (4) — — 50 pF 7 P52, P47, P24* , 7 P23* , P17, P16, 8 TEST* — — 20 pF Input pins except (4) above — — 15 pF — 80 100 mA Normal operation (other than the above) — 60 80 mA Sleep mode (with on-chip USB) — 60 80 mA Sleep mode (other than the above) 6 Standby mode* — 45 63 mA — 0.2 5.0 µA Ta ≤ 50°C — — 20.0 µA 50°C < Ta — 1.5 3.0 mA — 0.01 5.0 µA AVCC = 2.0 V to 5.5 V 4.5 — 5.5 V Operating Idle/not used Current Normal operation 5 dissipation* (with on-chip USB) Analog power supply current During A/D conversion ICC AlCC Idle 1 Analog power supply voltage* AVCC RAM standby voltage VRAM 2.0 — 5.5 V 2.0 — — V f = 20 MHz Notes: 1. Do not leave the AVCC, and AVSS pins open even if the A/D converter is not used. Even if the A/D converter is not used, apply a value in the range 2.0 V to 5.5 V to AVCC by connection to the power supply (VCC), or some other method. 2. P67 to P60 include supporting module inputs multiplexed on those pins. 3. IRQ2 includes the ADTRG signal multiplexed on that pin. Rev. 3.00 Mar 17, 2006 page 537 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 4. P52/SCK0/SCL0 and P47/SDA0 are NMOS push-pull outputs. An external pull-up resistor is necessary to provide high-level output from SCL0 and SDA0 (ICE = 1). P52/SCK0 and P47 (ICE = 0) high levels are driven by NMOS. 5. Current dissipation values are for VIH min = VCC – 0.2 V and VIL max = 0.2 V with all output pins unloaded and the on-chip pull-up MOSs in the off state. 6. The values are for VRAM ≤ VCC < 4.5 V, VIH min = VCC × 0.9, and VIL max = 0.3 V. 7. In the H8/3577 8. In the H8/3567 Table 22.3 Permissible Output Currents Conditions: VCC = 4.0 to 5.5 V, AVCC = 4.5 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to +75°C Item Permissible output low current (per pin) SCL1, SCL0, SDA1, SDA0 Symbol Min Typ Max Unit IOL — — 20 mA — — 2 mA Permissible output low current (total) Other output pins Total of all output pins, including the above ∑ IOL — — 120 mA Permissible output high current (per pin) All output pins –IOH — — 2 mA Permissible output high current (total) Total of all output pins ∑ –IOH — — 40 mA Notes: 1. To protect chip reliability, do not exceed the output current values in table 22.3. 2. When driving a Darlington pair or LED, always insert a current-limiting resistor in the output line, as show in figure 22.1. Rev. 3.00 Mar 17, 2006 page 538 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics Table 22.4 Bus Drive Characteristics Conditions: VCC = 4.5 to 5.5 V, VSS = 0 V, Ta = –20 to +75°C Applicable Pins: SCL1, SCL0, SDA1, SDA0 (bus drive function selected) Item Schmitt trigger input voltage Symbol – VT Min Typ Max Unit VCC × 0.3 — — V Test Conditions — — VCC × 0.7 VT – VT VCC × 0.05 — — Input high voltage VIH VCC × 0.7 — VCC + 0.5 V Input low voltage VIL –0.5 — VCC × 0.3 V Output low voltage VOL — — 0.8 V — — 0.5 IOL = 8 mA — — 0.4 IOL = 3 mA — — 20 pF Vin = 0 V, f = 1 MHz, Ta = 25°C Three-state leakage | ITSI | current (off state) — — 1.0 µA Vin = 0.5 to VCC – 0.5 V SCL, SDA output fall time 20 + 0.1Cb — 250 ns + VT + Input capacitance Cin tOf – IOL = 16 mA H8/3577 Group or H8/3567 Group chip 2 kΩ Port Darlington pair Figure 22.1 Darlington Pair Drive Circuit (Example) Rev. 3.00 Mar 17, 2006 page 539 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.3 AC Characteristics Figure 22.2 shows the test conditions for the AC characteristics. VCC RL Chip output pin C RH Figure 22.2 Output Load Circuit Rev. 3.00 Mar 17, 2006 page 540 of 706 REJ09B0303-0300 C = 30 pF: All ports RL = 2.4 kΩ RH = 12 kΩ I/O timing test levels • Low level: 0.8 V • High level: 2.0 V (except P47 and P52) Section 22 Electrical Characteristics 22.3.1 Clock Timing Table 22.5 shows the clock timing. The clock timing specified here covers clock (φ) output and clock pulse generator (crystal) and external clock input (EXTAL pin) oscillation settling times. For details of external clock input (EXTAL pin) timing, see section 20, Clock Pulse Generator. Table 22.5 Clock Timing Condition A: VCC = 5.0 V ±10%, VSS = 0 V, φ = 2 MHz to maximum operating frequency, Ta = –20 to +75°C Condition A 20 MHz Item Symbol Min Max Unit Test Conditions Clock cycle time tcyc 50 500 ns Figure 22.3 Clock high pulse width tCH 17 — ns Clock low pulse width tCL 17 — ns Clock rise time tCr — 8 ns Clock fall time tCf — 8 ns Oscillation settling time at reset (crystal) tOSC1 10 — ms Oscillation settling time in software standby (crystal) tOSC2 8 — ms External clock output stabilization delay time tDEXT 500 — µs Figure 22.4 Figure 22.5 tcyc tCH tCf φ tCL tCr Figure 22.3 System Clock Timing Rev. 3.00 Mar 17, 2006 page 541 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics EXTAL tDEXT tDEXT VCC STBY tOSC1 tOSC1 RES φ Figure 22.4 Oscillation Settling Timing φ NMI IRQi (i = 0, 1, 2) tOSC2 Figure 22.5 Oscillation Setting Timing (Exiting Software Standby Mode) Rev. 3.00 Mar 17, 2006 page 542 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.3.2 Control Signal Timing Table 22.6 shows the control signal timing. Table 22.6 Control Signal Timing Condition A: VCC = 5.0 V ±10%, VSS = 0 V, φ = 2 MHz to maximum operating frequency, Ta = –20 to +75°C Condition A 20 MHz Item Symbol Min Max Unit Test Conditions RES setup time tRESS 200 — ns Figure 22.6 RES pulse width tRESW 20 — tcyc NMI setup time (NMI) tNMIS 150 — ns NMI hold time (NMI) tNMIH 10 — NMI pulse width (exiting software standby mode) tNMIW 200 — ns IRQ setup time (IRQ2 to IRQ0) tIRQS 150 — ns IRQ hold time (IRQ2 to IRQ0) tIRQH 10 — ns IRQ pulse width (IRQ2 to IRQ0) (exiting software standby mode) tIRQW 200 — ns Figure 22.7 φ tRESS tRESS RES tRESW Figure 22.6 Reset Input Timing Rev. 3.00 Mar 17, 2006 page 543 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics φ tNMIH tNMIS NMI tNMIW IRQi (i = 2 to 0) tIRQW tIRQS tIRQH IRQ Edge input tIRQS IRQ Level input Figure 22.7 Interrupt Input Timing Rev. 3.00 Mar 17, 2006 page 544 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.3.3 Timing of On-Chip Supporting Modules Tables 22.7 and 22.8 show the on-chip supporting module timing. Table 22.7 Timing of On-Chip Supporting Modules Condition A: VCC = 5.0 V ±10%, VSS = 0 V, φ = 2 MHz to maximum operating frequency, Ta = –20 to +75°C Condition A 20 MHz Item Symbol I/O ports Output data delay time FRT TMR Min Max Unit Test Conditions ns Figure 22.8 (1) tPWDA, tPWDB — 50 Input data setup time tPRSA, tPRSB 30 — Input data hold time tPRHA, tPRHB 30 — Timer output delay time tFTOD — 50 Timer input setup time tFTIS 30 — Timer clock input setup time tFTCS 30 — Timer clock pulse width Single edge tFTCWH 1.5 — Both edges tFTCWL 2.5 — Timer output delay time tTMOD — 50 Timer reset input setup time tTMRS 30 — Figure 22.13 Timer clock input setup time tTMCS 30 — Figure 22.12 Single edge tTMCWH 1.5 — Both edges tTMCWL 2.5 — tPWOD — 50 ns Figure 22.14 Asynchronous tScyc 4 — tcyc Figure 22.15 Synchronous 6 — Timer clock pulse width PWM, PWMX Pulse output delay time SCI Input clock cycle Figure 22.8 (2) ns Figure 22.9 Figure 22.10 tcyc ns Figure 22.11 tcyc Input clock pulse width tSCKW 0.4 0.6 tScyc Input clock rise time tSCKr — 1.5 tcyc Input clock fall time tSCKf — 1.5 Transmit data delay time (synchronous) tTXD — 50 Receive data setup time (synchronous) tRXS 50 — ns Figure 22.16 Rev. 3.00 Mar 17, 2006 page 545 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics Condition A 20 MHz Item SCI Receive data hold time (synchronous) A/D Trigger input setup time converter Symbol Min Max Unit Test Conditions tRXH 50 — ns Figure 22.16 tTRGS 30 — ns Figure 22.17 T1 T2 φ tPRSA tPRHA Ports 1 to 7 (read) tPWDA Ports 1 to 6 (write) Figure 22.8 (1) I/O Port Input/Output Timing T1 T2 φ tPRSB tPRHB Ports C and D (read) tPWDB Ports C and D (write) Figure 22.8 (2) I/O Port Input/Output Timing (USB On-Chip Version) Rev. 3.00 Mar 17, 2006 page 546 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics φ tFTOD FTOA, FTOB tFTIS FTIA, FTIB, FTIC, FTID Figure 22.9 FRT Input/Output Timing φ tFTCS FTCI tFTCWL tFTCWH Figure 22.10 FRT Clock Input Timing φ tTMOD TMO0, TMO1 TMOX Figure 22.11 8-Bit Timer Output Timing Rev. 3.00 Mar 17, 2006 page 547 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics φ tTMCS tTMCS TMCI0, TMCI1 TMIX, TMIY tTMCWL tTMCWH Figure 22.12 8-Bit Timer Clock Input Timing φ tTMRS TMRI0, TMRI1 TMIX, TMIY Figure 22.13 8-Bit Timer Reset Input Timing φ tPWOD PW7 to PW0*1 PW15 to PW0*2 PWX1, PWX0 Notes: 1. In the H8/3577 2. In the H8/3567 Figure 22.14 PWM, PWMX Output Timing tSCKW tSCKr tSCKf SCK0, SCK1 tScyc Figure 22.15 SCK Clock Input Timing Rev. 3.00 Mar 17, 2006 page 548 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics SCK0 tTXD TxD0 (transmit data) tRXS tRXH RxD0 (receive data) Figure 22.16 SCI Input/Output Timing (Synchronous Mode) φ tTRGS ADTRG Figure 22.17 A/D Converter External Trigger Input Timing Rev. 3.00 Mar 17, 2006 page 549 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 2 Table 22.8 I C Bus Timing Conditions: VCC = 4.5 V to 5.5 V, VSS = 0 V, φ = 5 MHz to maximum operating frequency, Ta = –20 to +75°C Item Symbol Min Typ Max Unit SCL clock cycle time tSCL 12 — — tcyc SCL clock high pulse width tSCLH 3 — — tcyc SCL clock low pulse width tSCLL 5 — — tcyc SCL, SDA input rise time tSr — — 7.5* tcyc SCL, SDA input fall time tSf — — 300 ns SCL, SDA input spike pulse elimination time tSP — — 1 tcyc SDA input bus free time tBUF 5 — — tcyc Start condition input hold time tSTAH 3 — — tcyc Retransmission start condition input setup time tSTAS 3 — — tcyc Stop condition input setup time tSTOS 3 — — tcyc Data input setup time tSDAS 0.5 — — tcyc Data input hold time tSDAH 0 — — ns SCL, SDA capacitive load Cb — — 400 pF Note: * Test Conditions Notes Figure 22.18 2 17.5tcyc can be set according to the clock selected for use by the I C module. For details, see section 16.4, Usage Notes. Rev. 3.00 Mar 17, 2006 page 550 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics VIH SDA0, SDA1 VIL tBUF tSTAH SCL0, SCL1 P* tSCLH tSTAS S* tSf tSP tSTOS Sr* tSCLL tSr tSCL P* tSDAS tSDAH Note: * S, P, and Sr indicate the following conditions. S: Start condition P: Stop condition Sr: Retransmission start condition 2 Figure 22.18 I C Bus Interface Input/Output Timing Rev. 3.00 Mar 17, 2006 page 551 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.4 A/D Conversion Characteristics Table 22.9 lists the A/D conversion characteristics. Table 22.9 A/D Conversion Characteristics 1 (AN7 to AN0 Input* : 134/266-State Conversion) Condition A: VCC = 5.0 V ±10%, AVCC = 4.5 V to 5.5 V 2 VSS = AVSS = 0 V* , φ = 2 MHz to maximum operating frequency, Ta = –20 to +75°C Condition A 20 MHz Item Resolution Conversion time (single mode)* 5 Analog input capacitance Permissible signal-source impedance Min Typ Max Unit 10 10 10 Bits — — 6.7 µs — — 20 pF — 3 10* kΩ — 4 5* Nonlinearity error — — ±3.0 LSB Offset error — — ±3.5 LSB Full-scale error — — ±3.5 LSB Quantization error — — ±0.5 LSB ±4.0 LSB Absolute accuracy Notes: 1. In the H8/3577 (AN3 to AN0 in the H8/3567) 2. The voltage applied to the ANn analog input pins during A/D conversion must be in the range AVSS ≤ ANn ≤ AVCC (where n = 0 to 3). For the relationship between AVCC/AVSS and VCC/VSS, set AVSS = VSS. The AVCC and AVSS pins must not be left open when the A/D converter is not used. 3. When conversion time ≥ 11. 17 µs (CKS = 1 and φ ≤ 12 MHz, or CKS = 0) 4. When conversion time < 11. 17 µs (CKS = 1 and φ > 12 Mhz) 5. Value when using the maximum operating frequency. Rev. 3.00 Mar 17, 2006 page 552 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.5 USB Function Pin Characteristics Table 22.10 shows the USB function pin characteristics. Table 22.10 DC Characteristics Conditions: VCC = 5.0 V ±10%, DrVCC = 3.3 V ± 0.3 V, DrVSS = VSS = 0 V, Ta = –20°C to +75°C Pin Functions: Transceiver input/output (USD+, USD−, DS2D+, DS2D−, DS3D+, DS3D−, DS4D+, DS4D−, DS5D+, DS5D−), ports C and D, ENP2 to ENP5, OCP2 to OCP5, EXTAL12, XTAL12 Item Symbol Min Typ Max Unit Test Conditions Differential input sensitivity VDI 0.2 — — V | (D+) − (D−) | Differential common mode range VCM 0.8 — 2.5 V Including VDI Schmitt OCP2 to trigger input OCP5 voltages VT 1.0 — — V — — VCC × 0.7 V VT – VT 0.4 — — V VIH VCC × 0.7 — VCC + 0.3 V Port D 2.0 — DrVCC + 0.3 V Other than the above 2.0 — VCC + 0.3 V –0.3 — VCC × 0.2 V –0.3 — 0.8 V 2.8 — 3.6 V RL = 15 kΩ connected between pin and GND DrVCC – 0.5 — — V IOH = –200 µA DrVCC – 1.0 — — V IOH = –1 mA VCC – 0.5 — — V IOH = –200 µA 3.5 — — V IOH = –1 mA – + VT + 1 Input high* EXTAL12 voltage 1 Input low* voltage EXTAL12 VIL Other than the above Output high Transceiver VOH voltage Port D Other than the above – Rev. 3.00 Mar 17, 2006 page 553 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics Item Output low voltage Symbol Min Typ Max Unit Test Conditions Transceiver VOL — — 0.3 V RL = 1.5 kΩ connected between pin and power supply Other than the above — — 0.4 V IOL = 1.6 mA Output resistance ZDRV 28 — 44 Ω Input pin capacitance CIN — — 35 pF Between pin and GND Three-state leakage current ILO — — 1.0 µA 0.5 V < Vin < DrVCC – 0.5 V 0.5 V < Vin < VCC – 2 0.5 V* DrVCC current dissipation Normal operation Standby mode DICC — 5 10 mA — 0.2 5.0 µA Notes: 1. Excluding transceiver input/output (USD+, USD−, DS2D+, DS2D−, DS3D+, DS3D−, DS4D+, DS4D−, DS5D+, DS5D−) 2. Upper row applies to transceiver input/output and port D, and lower row to other pins. Rev. 3.00 Mar 17, 2006 page 554 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics Table 22.11 AC Characteristics Conditions: VCC = 5.0 V ±10%, DrVCC = 3.3 V ± 0.3 V, DrVSS = VSS = 0 V, Ta = –20°C to +75°C Pin Functions: Transceiver input/output (USD+, USD−, DS2D+, DS2D−, DS3D+, DS3D−, DS4D+, DS4D−, DS5D+, DS5D−), ports C and D, ENP2 to ENP5, OCP2 to OCP5, EXTAL12, XTAL12 Item Symbol Min Max Unit Figure Rise time tFR 4 20 ns Figure 22.19 Fall time tFF 4 20 Differential signal time difference tFRFM 90.0 111.11 % Rise time tLR 75 300 ns Fall time tLF 75 300 Differential signal time difference tLRFM 80.0 125 % Transceiver output signal crossing voltage VCRS 1.3 2.0 V Ports C and D Output data delay time tPWDB — 50 ns Input data setup time tPRSB 30 — Input data hold time tPRHB 30 — tOSCU 10 — tFR tLR tFF tLF Transceiver full speed Transceiver low speed USB clock oscillation settling time (crystal) Notes tFR/tFF Figure 22.19 tLR/tLF Figure 22.8 (2) ms VOH VOL Figure 22.19 Transceiver Output Timing Rev. 3.00 Mar 17, 2006 page 555 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics 22.6 Usage Notes ZTAT Version and Mask ROM Version: The ZTAT and mask ROM versions satisfy the electrical characteristics shown in this manual, but actual electrical characteristic values, operating margins, noise margins, and other properties may vary due to differences in manufacturing process, on-chip ROM, layout patterns, and so on. When system evaluation testing is carried out using the ZTAT version, the same evaluation testing should also be conducted for the mask ROM version when changing over to that version. Models with Internal Step-Down Circuit: H8/3577, H8/3567, and H8/3567U mask ROM models (HD6433577, HD6433574, HD6433567, HD6433564-20, HD6433564-10, HD6433567U, and HD6433564U) incorporate an internal step-down circuit to lower the MCU’s internal power supply voltage to the optimum level automatically. One or two (in-parallel) 0.47 µF internal voltage stabilization capacitors must be connected between the internal step-down pin (VCL) and the VSS pin. The method of connecting the external capacitor(s) is shown in figure 22.20. Do not apply a voltage exceeding 3.6 V to the VCL pin. When switching from a ZTAT version with no internal step-down capability to a mask ROM version with the step-down facility, the differences in the circuitry before and after the changeover must be taken into consideration when designing the board pattern. Rev. 3.00 Mar 17, 2006 page 556 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics External capacitor(s) for power supply stabilization Vcc power supply VCL One or two (in-parallel) 0.47 µF capacitors VSS Model with internal step-down capability (mask ROM version) VCC 10 µF bypass capacitor 0.01 µF VSS Model without internal step-down capability (ZTAT version) Do not connect the VCC power supply to the VCL pin of a model with internal step-down capability. (Connect the VCC power supply to other VCC pins as usual.) A power supply stabilization capacitor must be connected to the VCL pin. Use one or two (in-parallel) 0.47 µF laminated ceramic capacitors, placed close to the pin. Models with no internal step-down capability have a VCC pin (VCC power supply pin) in the pin position occupied by the VCL pin in internal step-down models. It is recommended that a bypass capacitor be connected to the power supply pins. (Values are for reference.) Models with internal step-down capability: HD6433577, HD6433574, HD6433567, HD6433564-20, HD6433564-10, HD6433567U, HD6433564U Models without internal step-down capability: HD6473577, HD6473567, HD6473567U Figure 22.20 Method of Connecting VCL Capacitor(s) to Mask ROM Model with Internal Step-Down Capability, and Differences between Models with and without Internal Step-Down Capability Rev. 3.00 Mar 17, 2006 page 557 of 706 REJ09B0303-0300 Section 22 Electrical Characteristics Rev. 3.00 Mar 17, 2006 page 558 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Appendix A CPU Instruction Set A.1 Instruction Set List Operation Notation Rd8/16 General register (destination) (8 or 16 bits) Rs8/16 General register (source) (8 or 16 bits) Rn8/16 General register (8 or 16 bits) CCR Condition code register N N (negative) flag in CCR Z Z (zero) flag in CCR V V (overflow) flag in CCR C C (carry) flag in CCR PC Program counter SP Stack pointer #xx:3/8/16 Immediate data (3, 8, or 16 bits) d:8/16 Displacement (8 or 16 bits) @aa:8/16 Absolute address (8 or 16 bits) + Addition – Subtraction × Multiplication ÷ Division ∧ Logical AND ∨ Logical OR ⊕ Exclusive logical OR → — Move NOT (logical complement) Condition Code Notation Modified according to the instruction result * Undetermined (unpredictable) 0 Always cleared to 0 — Not affected by the instruction result Rev. 3.00 Mar 17, 2006 page 559 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Instruction Set B @(d:16, Rs16) → Rd8 MOV.B @Rs+, Rd B @Rs16 → Rd8 Rs16+1 → Rs16 MOV.B @aa:8, Rd B @aa:8 → Rd8 MOV.B @aa:16, Rd B @aa:16 → Rd8 MOV.B Rs, @Rd B Rs8 → @Rd16 MOV.B Rs, @(d:16, Rd) B Rs8 → @(d:16, Rd16) MOV.B Rs, @–Rd B Rd16–1 → Rd16 Rs8 → @Rd16 MOV.B Rs, @aa:8 B Rs8 → @aa:8 Implied @aa: 8/16 @(d:8, PC) @@aa @–Rn/@Rn+ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ MOV.B @(d:16, Rs), Rd ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ B @Rs16 → Rd8 0 — 4 ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ B Rs8 → Rd8 MOV.B @Rs, Rd 0 — 2 0 — 4 0 — 6 MOV.W Rs, @–Rd W Rd16–2 → Rd16 Rs16 → @Rd16 ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ MOV.B Rs, Rd I H N Z V C MOV.W Rs, @aa:16 W Rs16 → @aa:16 0 — 6 POP Rd W @SP → Rd16 SP+2 → SP 2 — — ↔ ↔ ↔ ↔ B #xx:8 → Rd8 Condition Code PUSH Rs W SP–2 → SP Rs16 → @SP 2 — — ↔ ↔ MOV.B #xx:8, Rd Rn @Rn @(d:16, Rn) Operation #xx: 8/16 Mnemonic Operand Size Addressing Mode/ Instruction Length No. of States* Table A.1 0 — 6 MOV.B Rs, @aa:16 B Rs8 → @aa:16 MOV.W #xx:16, Rd W #xx:16 → Rd16 MOV.W Rs, Rd W Rs16 → Rd16 MOV.W @Rs, Rd W @Rs16 → Rd16 2 — — 2 — — 2 4 W @Rs16 → Rd16 Rs16+2 → Rs16 MOV.W @aa:16, Rd W @aa:16 → Rd16 MOV.W Rs, @Rd W Rs16 → @Rd16 MOV.W Rs, @(d:16, Rd) W Rs16 → @(d:16, Rd16) Rev. 3.00 Mar 17, 2006 page 560 of 706 REJ09B0303-0300 — — 2 — — 2 — — 4 — — 2 — — 4 — — 2 — — 2 — — 4 — — 4 — — 2 — — 2 MOV.W @(d:16, Rs), Rd W @(d:16, Rs16) → Rd16 MOV.W @Rs+, Rd — — — — 4 — — 2 — — 4 2 — — — — 4 — — 2 — — 4 — — 0 — 2 0 — 4 0 — 6 0 — 6 0 — 6 0 — 4 0 — 6 0 — 6 0 — 6 0 — 4 0 — 2 0 — 4 0 — 6 0 — 6 0 — 4 0 — 6 0 — 6 0 — 6 Appendix A CPU Instruction Set MOVTPE Rs, @aa:16 B Not supported ADD.B #xx:8, Rd B Rd8+#xx:8 → Rd8 2 — H N Z V C No. of States* @(d:8, PC) @@aa Implied @aa: 8/16 I ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ B Not supported Condition Code ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ MOVFPE @aa:16, Rd @Rn @(d:16, Rn) @–Rn/@Rn+ Operation #xx: 8/16 Rn Mnemonic Operand Size Addressing Mode/ Instruction Length 2 B Rd8+Rs8 → Rd8 2 — ADD.W Rs, Rd W Rd16+Rs16 → Rd16 2 — (1) ADDX.B #xx:8, Rd B Rd8+#xx:8 +C → Rd8 ADDX.B Rs, Rd B Rd8+Rs8 +C → Rd8 2 — ADDS.W #1, Rd W Rd16+1 → Rd16 2 — — — — — — 2 ADDS.W #2, Rd W Rd16+2 → Rd16 2 — — — — — — 2 INC.B Rd B Rd8+1 → Rd8 2 — — DAA.B Rd B Rd8 decimal adjust → Rd8 2 — * SUB.B Rs, Rd B Rd8–Rs8 → Rd8 2 — SUB.W Rs, Rd W Rd16–Rs16 → Rd16 2 — (1) SUBX.B #xx:8, Rd B Rd8–#xx:8 –C → Rd8 SUBX.B Rs, Rd B Rd8–Rs8 –C → Rd8 2 — SUBS.W #1, Rd W Rd16–1 → Rd16 2 — — — — — — 2 SUBS.W #2, Rd W Rd16–2 → Rd16 2 — — — — — — 2 DEC.B Rd B Rd8–1 → Rd8 2 — — DAS.B Rd B Rd8 decimal adjust → Rd8 2 — * NEG.B Rd B 0–Rd8 → Rd8 2 — CMP.B #xx:8, Rd B Rd8–#xx:8 2 — (2) 2 2 2 — 2 ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ (2) 2 * (3) 2 ↔ — (2) 2 2 2 2 — 2 * — 2 ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ 2 (2) ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ — ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ 2 ↔ ADD.B Rs, Rd 2 2 B Rd8–Rs8 2 — CMP.W Rs, Rd W Rd16–Rs16 2 — (1) MULXU.B Rs, Rd B Rd8 × Rs8 → Rd16 2 — — — — — — 14 DIVXU.B Rs, Rd B Rd16÷Rs8 → Rd16 (RdH: remainder, RdL: quotient) 2 — — (6) (7) — — 14 AND.B #xx:8, Rd B Rd8∧#xx:8 → Rd8 AND.B Rs, Rd B Rd8∧Rs8 → Rd8 — — 2 2 — — ↔ ↔ ↔ ↔ CMP.B Rs, Rd 2 2 0 — 2 0 — 2 Rev. 3.00 Mar 17, 2006 page 561 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set H N Z V C 2 — — 2 — — 0 2 — — 2 — — 2 — — 2 — — SHLL.B Rd B C B C 0 B C C B C 2 0 2 0 2 0 2 0 2 b0 C b7 ROTR.B Rd 0 b0 B b7 ROTL.B Rd 2 b0 b7 ROTXR.B Rd 0 b0 0 b7 ROTXL.B Rd 2 b0 b7 SHLR.B Rd 0 b0 B b7 ↔ ↔ — — SHAR.B Rd ↔ 2 b7 2 ↔ — — 0 ↔ 2 C ↔ B 0 — 2 ↔ SHAL.B Rd 0 — 2 ↔ — — 0 — 2 ↔ — — 2 0 — 2 ↔ ↔ 2 B Rd8 → Rd8 — — ↔ ↔ B Rd8⊕Rs8 → Rd8 NOT.B Rd — — ↔ XOR.B Rs, Rd 2 2 ↔ ↔ B Rd8⊕#xx:8 → Rd8 0 — 2 ↔ ↔ B Rd8∨Rs8 → Rd8 XOR.B #xx:8, Rd — — ↔ ↔ OR.B Rs, Rd 2 ↔ ↔ B Rd8∨#xx:8 → Rd8 ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ I OR.B #xx:8, Rd No. of States* Condition Code Implied @aa: 8/16 @(d:8, PC) @@aa @–Rn/@Rn+ Rn @Rn @(d:16, Rn) Operation #xx: 8/16 Mnemonic Operand Size Addressing Mode/ Instruction Length b0 B C b7 Rev. 3.00 Mar 17, 2006 page 562 of 706 REJ09B0303-0300 b0 Appendix A CPU Instruction Set B (#xx:3 of Rd8) ← 1 BSET #xx:3, @Rd B (#xx:3 of @Rd16) ← 1 BSET #xx:3, @aa:8 B (#xx:3 of @aa:8) ← 1 BSET Rn, Rd B (Rn8 of Rd8) ← 1 BSET Rn, @Rd B (Rn8 of @Rd16) ← 1 BSET Rn, @aa:8 B (Rn8 of @aa:8) ← 1 BCLR #xx:3, Rd B (#xx:3 of Rd8) ← 0 BCLR #xx:3, @Rd B (#xx:3 of @Rd16) ← 0 BCLR #xx:3, @aa:8 B (#xx:3 of @aa:8) ← 0 BCLR Rn, Rd B (Rn8 of Rd8) ← 0 BCLR Rn, @Rd B (Rn8 of @Rd16) ← 0 BCLR Rn, @aa:8 B (Rn8 of @aa:8) ← 0 BNOT #xx:3, Rd B (#xx:3 of Rd8) ← (#xx:3 of Rd8) BNOT #xx:3, @Rd B (#xx:3 of @Rd16) ← (#xx:3 of @Rd16) BNOT #xx:3, @aa:8 B (#xx:3 of @aa:8) ← (#xx:3 of @aa:8) BNOT Rn, Rd B (Rn8 of Rd8) ← (Rn8 of Rd8) BNOT Rn, @Rd B (Rn8 of @Rd16) ← (Rn8 of @Rd16) BNOT Rn, @aa:8 B (Rn8 of @aa:8) ← (Rn8 of @aa:8) BTST #xx:3, Rd B (#xx:3 of Rd8) → Z BTST #xx:3, @Rd B (#xx:3 of @Rd16) → Z BTST #xx:3, @aa:8 B (#xx:3 of @aa:8) → Z BTST Rn, Rd B (Rn8 of Rd8) → Z BTST Rn, @Rd B (Rn8 of @Rd16) → Z BTST Rn, @aa:8 B (Rn8 of @aa:8) → Z I H N Z V C No. of States* @(d:8, PC) @@aa Implied @(d:16, Rn) @–Rn/@Rn+ @aa: 8/16 2 Condition Code — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — 4 — — — 4 2 — — — — — — 4 — — — 4 — — — ↔ ↔ ↔ ↔ ↔ ↔ BSET #xx:3, Rd @Rn Operation #xx: 8/16 Rn Mnemonic Operand Size Addressing Mode/ Instruction Length — — 2 — — 6 — — 6 — — 2 — — 6 — — 6 Rev. 3.00 Mar 17, 2006 page 563 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set BLD #xx:3, @Rd B (#xx:3 of @Rd16) → C BLD #xx:3, @aa:8 B (#xx:3 of @aa:8) → C BILD #xx:3, Rd B (#xx:3 of Rd8) → C BILD #xx:3, @Rd B (#xx:3 of @Rd16) → C BILD #xx:3, @aa:8 B (#xx:3 of @aa:8) → C BST #xx:3, Rd B C → (#xx:3 of Rd8) BST #xx:3, @Rd B C → (#xx:3 of @Rd16) BST #xx:3, @aa:8 B C → (#xx:3 of @aa:8) BIST #xx:3, Rd B C → (#xx:3 of Rd8) BIST #xx:3, @Rd B C → (#xx:3 of @Rd16) BIST #xx:3, @aa:8 B C → (#xx:3 of @aa:8) BAND #xx:3, Rd B C∧(#xx:3 of Rd8) → C BAND #xx:3, @Rd B C∧(#xx:3 of @Rd16) → C BAND #xx:3, @aa:8 B C∧(#xx:3 of @aa:8) → C BIAND #xx:3, Rd B C∧(#xx:3 of Rd8) → C BIAND #xx:3, @Rd B C∧(#xx:3 of @Rd16) → C BIAND #xx:3, @aa:8 B C∧(#xx:3 of @aa:8) → C BOR #xx:3, Rd B C∨(#xx:3 of Rd8) → C BOR #xx:3, @Rd B C∨(#xx:3 of @Rd16) → C BOR #xx:3, @aa:8 B C∨(#xx:3 of @aa:8) → C BIOR #xx:3, Rd B C∨(#xx:3 of Rd8) → C BIOR #xx:3, @Rd B C∨(#xx:3 of @Rd16) → C BIOR #xx:3, @aa:8 B C∨(#xx:3 of @aa:8) → C BXOR #xx:3, Rd B C⊕(#xx:3 of Rd8) → C BXOR #xx:3, @Rd B C⊕(#xx:3 of @Rd16) → C BXOR #xx:3, @aa:8 B C⊕(#xx:3 of @aa:8) → C BIXOR #xx:3, Rd B C⊕(#xx:3 of Rd8) → C Rev. 3.00 Mar 17, 2006 page 564 of 706 REJ09B0303-0300 H N Z V C — — — — — 4 2 — — — — — — — — — — 4 — — — — — 4 2 — — — — — No. of States* I — — — — — 4 2 6 6 2 6 6 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — — 2 4 — — — — — — 8 4 2 — — — — — — 8 — — — — — 4 — — — — — 4 2 — — — — — — — — — — 4 — — — — — 4 2 — — — — — — — — — — 4 — — — — — 4 2 — — — — — — — — — — 4 — — — — — 4 2 — — — — — — — — — — 4 — — — — — 4 2 Implied @aa: 8/16 @(d:8, PC) @@aa @Rn @(d:16, Rn) @–Rn/@Rn+ 2 ↔ ↔ ↔ ↔ ↔ ↔ B (#xx:3 of Rd8) → C Condition Code — — — — — — — — — — ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ BLD #xx:3, Rd Rn Operation #xx: 8/16 Mnemonic Operand Size Addressing Mode/ Instruction Length 2 6 6 2 6 6 2 6 6 2 6 6 2 6 6 2 Appendix A CPU Instruction Set B C⊕(#xx:3 of @Rd16) → C 4 I H N Z V C — — — — — No. of States* @(d:8, PC) @@aa Implied @(d:16, Rn) @–Rn/@Rn+ @aa: 8/16 @Rn Branching Condition Condition Code ↔ ↔ BIXOR #xx:3, @Rd Operation #xx: 8/16 Rn Mnemonic Operand Size Addressing Mode/ Instruction Length 6 BIXOR #xx:3, @aa:8 B C⊕(#xx:3 of @aa:8) → C BRA d:8 (BT d:8) — PC ← PC+d:8 2 — — — — — — 4 BRN d:8 (BF d:8) — PC ← PC+2 2 — — — — — — 4 BHI d:8 C∨Z=0 2 — — — — — — 4 C∨Z=1 2 — — — — — — 4 C=0 2 — — — — — — 4 C=1 2 — — — — — — 4 Z=0 2 — — — — — — 4 BEQ d:8 — If condition — is true — then — PC ← PC+d:8 — else next; — Z=1 2 — — — — — — 4 BVC d:8 — V=0 2 — — — — — — 4 BVS d:8 — V=1 2 — — — — — — 4 BPL d:8 — N=0 2 — — — — — — 4 BMI d:8 — N=1 2 — — — — — — 4 BGE d:8 — N⊕V = 0 2 — — — — — — 4 BLT d:8 — N⊕V = 1 2 — — — — — — 4 BGT d:8 — Z ∨ (N⊕V) = 0 2 — — — — — — 4 BLE d:8 — Z ∨ (N⊕V) = 1 2 — — — — — — 4 JMP @Rn — PC ← Rn16 JMP @aa:16 — PC ← aa:16 JMP @@aa:8 — PC ← @aa:8 BSR d:8 — SP–2 → SP PC → @SP PC ← PC+d:8 JSR @Rn — SP–2 → SP PC → @SP PC ← Rn16 JSR @aa:16 — SP–2 → SP PC → @SP PC ← aa:16 BLS d:8 BCC d:8 (BHS d:8) BCS d:8 (BLO d:8) BNE d:8 4 — — — — — 2 6 — — — — — — 4 4 — — — — — — 6 2 2 2 — — — — — — 8 — — — — — — 6 — — — — — — 6 4 — — — — — — 8 Rev. 3.00 Mar 17, 2006 page 565 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set I H N Z V C No. of States* Condition Code Implied @aa: 8/16 @(d:8, PC) @@aa @–Rn/@Rn+ Rn @Rn @(d:16, Rn) Operation #xx: 8/16 Mnemonic Operand Size Addressing Mode/ Instruction Length JSR @@aa:8 — SP–2 → SP PC → @SP PC ← @aa:8 RTS — PC ← @SP SP+2 → SP 2 — — — — — — 8 RTE — CCR ← @SP SP+2 → SP PC ← @SP SP+2 → SP 2 SLEEP — Transit to sleep mode. 2 — — — — — — 2 LDC #xx:8, CCR B #xx:8 → CCR LDC Rs, CCR B Rs8 → CCR STC CCR, Rd B CCR → Rd8 ANDC #xx:8, CCR B CCR∧#xx:8 → CCR 2 ORC #xx:8, CCR B CCR∨#xx:8 → CCR 2 XORC #xx:8, CCR B CCR⊕#xx:8 → CCR 2 NOP — PC ← PC+2 EEPMOV — EEPMOV Notes: * (1) (2) (3) (5) (6) (7) ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ ↔ — — — — — — 2 ↔ ↔ ↔ 2 2 2 2 2 2 2 — — — — — — 2 These cannot be used in this LSI. The number of states is the number of states required for execution when the instruction and its operands are located in on-chip memory. For other cases, see section A.3, Number of Instruction Execution States. Set to 1 when there is a carry or borrow from bit 11; otherwise cleared to 0. If the result is zero, the previous value of the flag is retained; otherwise the flag is cleared to 0. Set to 1 if decimal adjustment produces a carry; otherwise cleared to 0. These instructions are not supported by the H8/3577 Group and H8/3567 Group. Set to 1 if the divisor is negative; otherwise cleared to 0. Set to 1 if the divisor is 0; otherwise cleared to 0. Rev. 3.00 Mar 17, 2006 page 566 of 706 REJ09B0303-0300 10 2 2 ↔ ↔ ↔ ↔ ↔ ↔ ↔ — — — — — — 8 ↔ ↔ 2 (5) Appendix A CPU Instruction Set A.2 Operation Code Map Table A.2 is a map of the operation codes contained in the first byte of the instruction code (bits 15 to 8 of the first instruction word). Instruction when first bit of byte 2 (bit 7 of first instruction word) is 0. Instruction when first bit of byte 2 (bit 7 of first instruction word) is 1. Rev. 3.00 Mar 17, 2006 page 567 of 706 REJ09B0303-0300 Rev. 3.00 Mar 17, 2006 page 568 of 706 REJ09B0303-0300 OR XOR AND MOV C D E F SUB ADD MOV BVS 9 JMP BPL DEC INC A EEPMOV C CMP MOV BLT D JSR BGT SUBX ADDX E Bit manipulation instructions BGE MOV*1 BMI SUBS ADDS B Notes: 1. The MOVFPE and MOVTPE instructions are identical to MOV instructions in the first byte and first bit of the second byte (bits 15 to 7 of the instruction word). The PUSH and POP instructions are identical in machine language to MOV instructions. 2. The BT, BF, BHS, and BLO instructions are identical in machine language to BRA, BRN, BCC, and BCS, respectively. SUBX BILD 8 BVC B BIAND BAND BIST BLD BST BEQ MOV NEG NOT CMP BIXOR BXOR RTE BNE AND A BIOR BOR BSR BCS*2 XOR LDC ANDC XORC ADDX BTS RTS BCC*2 OR 7 6 5 9 BCLR BLS ROTR ROTXR ORC 4 ADD BNOT BHI ROTL LDC 3 8 7 BSET DIVXU MULXU 5 6 BRN*2 SHAR ROTXL STC SLEEP SHLR 2 1 BRA*2 SHAL SHLL NOP 0 4 3 2 Low BLE DAS DAA F Table A.2 1 0 High Appendix A CPU Instruction Set Operation Code Map Appendix A CPU Instruction Set A.3 Number of States Required for Execution The tables below can be used to calculate the number of states required for instruction execution. Table A.3 indicates the number of states required for each cycle (instruction fetch, branch address read, stack operation, byte data access, word data access, internal operation). Table A.4 indicates the number of cycles of each type occurring in each instruction. The total number of states required for execution of an instruction can be calculated from these two tables as follows: Execution states = I × SI + J × SJ + K × SK + L × SL + M × SM + N × SN Examples: Mode 1, stack located in external memory, 1 wait state inserted in external memory access. 1. BSET #0, @FFC7 From table A.4: I = L = 2, J = K = M = N= 0 From table A.3: SI = 8, SL = 3 Number of states required for execution: 2 × 8 + 2 × 3 =22 2. JSR @@30 From table A.4: I = 2, J = K = 1, L = M = N = 0 From table A.3: SI = SJ = SK = 8 Number of states required for execution: 2 × 8 + 1 × 8 + 1 × 8 = 32 Table A.3 Number of States Taken by Each Cycle in Instruction Execution Access Location Execution Status (Instruction Cycle) Instruction fetch SI Branch address read SJ On-Chip Memory On-Chip Reg. Field External Memory 2 6 6 + 2m Stack operation SK Byte data access SL 3 3+m Word data access SM 6 6 + 2m Internal operation SN 1 1 1 Note: m: Number of wait states inserted in access to external device. Rev. 3.00 Mar 17, 2006 page 569 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Table A.4 Number of Cycles in Each Instruction Instruction Mnemonic Instruction Branch Stack Byte Data Word Data Internal Fetch Addr. Read Operation Access Access Operation I J K L M N ADD ADD.B #xx:8, Rd 1 ADD.B Rs, Rd 1 ADD.W Rs, Rd 1 ADDS ADDS.W #1/2, Rd 1 ADDX ADDX.B #xx:8, Rd 1 AND ADDX.B Rs, Rd 1 AND.B #xx:8, Rd 1 AND.B Rs, Rd 1 ANDC ANDC #xx:8, CCR 1 BAND BAND #xx:3, Rd 1 BAND #xx:3, @Rd 2 1 BAND #xx:3, @aa:8 2 1 BRA d:8 (BT d:8) 2 Bcc BCLR BRN d:8 (BF d:8) 2 BHI d:8 2 BLS d:8 2 BCC d:8 (BHS d:8) 2 BCS d:8 (BLO d:8) 2 BNE d:8 2 BEQ d:8 2 BVC d:8 2 BVS d:8 2 BPL d:8 2 BMI d:8 2 BGE d:8 2 BLT d:8 2 BGT d:8 2 BLE d:8 2 BCLR #xx:3, Rd 1 BCLR #xx:3, @Rd 2 2 BCLR #xx:3, @aa:8 2 2 BCLR Rn, Rd 1 BCLR Rn, @Rd 2 2 BCLR Rn, @aa:8 2 2 Rev. 3.00 Mar 17, 2006 page 570 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Instruction Mnemonic Instruction Branch Stack Byte Data Word Data Internal Fetch Addr. Read Operation Access Access Operation I J K L M N BIAND BIAND #xx:3, Rd 1 BIAND #xx:3, @Rd 2 1 BIAND #xx:3, @aa:8 2 1 BILD BIOR BIST BIXOR BLD BNOT BOR BSET BILD #xx:3, Rd 1 BILD #xx:3, @Rd 2 1 BILD #xx:3, @aa:8 2 1 BIOR #xx:3, Rd 1 BIOR #xx:3, @Rd 2 1 BIOR #xx:3, @aa:8 2 1 BIST #xx:3, Rd 1 BIST #xx:3, @Rd 2 2 BIST #xx:3, @aa:8 2 2 BIXOR #xx:3, Rd 1 BIXOR #xx:3, @Rd 2 1 BIXOR #xx:3, @aa:8 2 1 BLD #xx:3, Rd 1 BLD #xx:3, @Rd 2 1 BLD #xx:3, @aa:8 2 1 BNOT #xx:3, Rd 1 BNOT #xx:3, @Rd 2 2 BNOT #xx:3, @aa:8 2 2 BNOT Rn, Rd 1 BNOT Rn, @Rd 2 2 BNOT Rn, @aa:8 2 2 BOR #xx:3, Rd 1 BOR #xx:3, @Rd 2 1 BOR #xx:3, @aa:8 2 1 BSET #xx:3, Rd 1 BSET #xx:3, @Rd 2 2 BSET #xx:3, @aa:8 2 2 BSET Rn, Rd 1 BSET Rn, @Rd 2 2 BSET Rn, @aa:8 2 2 Rev. 3.00 Mar 17, 2006 page 571 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Instruction Mnemonic Instruction Branch Stack Byte Data Word Data Internal Fetch Addr. Read Operation Access Access Operation I J K L M N BSR 2 BST BTST BXOR CMP BSR d:8 1 BST #xx:3, Rd 1 BST #xx:3, @Rd 2 2 BST #xx:3, @aa:8 2 2 BTST #xx:3, Rd 1 BTST #xx:3, @Rd 2 1 BTST #xx:3, @aa:8 2 1 BTST Rn, Rd 1 BTST Rn, @Rd 2 1 BTST Rn, @aa:8 2 1 BXOR #xx:3, Rd 1 BXOR #xx:3, @Rd 2 1 BXOR #xx:3, @aa:8 2 1 CMP.B #xx:8, Rd 1 CMP.B Rs, Rd 1 CMP.W Rs, Rd 1 DAA DAA.B Rd 1 DAS DAS.B Rd 1 DEC DEC.B Rd 1 DIVXU DIVXU.B Rs, Rd 1 EEPMOV EEPMOV This cannot be used in these H8/3577 Group and H8/3567 Group. INC INC.B Rd 1 JMP JMP @Rn 2 JMP @aa:16 2 JMP @@aa:8 2 JSR @Rn 2 JSR @aa:16 2 JSR @@aa:8 2 JSR LDC LDC #xx:8, CCR 1 LDC Rs, CCR 1 Rev. 3.00 Mar 17, 2006 page 572 of 706 REJ09B0303-0300 12 2 1 2 1 1 1 1 2 Appendix A CPU Instruction Set Instruction Mnemonic Instruction Branch Stack Byte Data Word Data Internal Fetch Addr. Read Operation Access Access Operation I J K L M N MOV MOV.B #xx:8, Rd 1 MOV.B Rs, Rd 1 MOV.B @Rs, Rd 1 1 MOV.B @(d:16,Rs), Rd 2 1 MOV.B @Rs+, Rd 1 1 MOV.B @aa:8, Rd 1 1 MOV.B @aa:16, Rd 2 1 MOV.B Rs, @Rd 1 1 MOV.B Rs, @(d:16, Rd) 2 1 2 MOV.B Rs, @–Rd 1 1 MOV.B Rs, @aa:8 1 1 MOV.B Rs, @aa:16 2 1 MOV.W #xx:16, Rd 2 MOV.W Rs, Rd 1 MOV.W @Rs, Rd 1 1 MOV.W @(d:16, Rs), 2 Rd 1 MOV.W @Rs+, Rd 2 1 1 MOV.W @aa:16, Rd 2 1 MOV.W Rs, @Rd 1 1 MOV.W Rs, @(d:16, 2 Rd) 1 MOV.W Rs, @–Rd 1 1 1 MOV.W Rs, @aa:16 2 MOVFPE MOVFPE @aa:16, Rd Not supported MOVTPE MOVTPE.Rs, @aa:16 Not supported MULXU MULXU.B Rs, Rd 1 NEG NEG.B Rd 1 NOP NOP 1 NOT NOT.B Rd 1 2 2 12 Rev. 3.00 Mar 17, 2006 page 573 of 706 REJ09B0303-0300 Appendix A CPU Instruction Set Instruction Mnemonic Instruction Branch Stack Byte Data Word Data Internal Fetch Addr. Read Operation Access Access Operation I J K L M N OR OR.B #xx:8, Rd 1 OR.B Rs, Rd 1 ORC ORC #xx:8, CCR 1 POP POP Rd 1 1 2 PUSH PUSH Rd 1 1 2 ROTL ROTL.B Rd 1 ROTR ROTR.B Rd 1 ROTXL ROTXL.B Rd 1 ROTXR ROTXR.B Rd 1 RTE RTE 2 2 2 RTS RTS 2 1 2 SHAL SHAL.B Rd 1 SHAR SHAR.B Rd 1 SHLL SHLL.B Rd 1 SHLR SHLR.B Rd 1 SLEEP SLEEP 1 STC STC CCR, Rd 1 SUB SUB.B Rs, Rd 1 SUB.W Rs, Rd 1 SUBS SUBS.W #1/2, Rd 1 SUBX SUBX.B #xx:8, Rd 1 SUBX.B Rs, Rd 1 XOR XORC XOR.B #xx:8, Rd 1 XOR.B Rs, Rd 1 XORC #xx:8, CCR 1 Note: All values left blank are zero. Rev. 3.00 Mar 17, 2006 page 574 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Appendix B Internal I/O Registers B.1 Addresses Register Address Name Bit 7 Bit 6 Bit 5 H'FDC0 UPRTCR — — DSPSEL2 DSPSEL1 DSPSEL0 PCNMD2 PCNMD1 PCNMD0 USB D7 D6 D5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Module Name Bus Width 8 H'FDC1 UTESTR0 H'FDC2 UTESTR1 H'FDE1 EPDR2 D4 D3 D2 D1 D0 H'FDE2 FVSR2H — — — — — — N9 N8 H'FDE3 FVSR2L N7 N6 N5 N4 N3 N2 N1 N0 H'FDE4 EPSZR1 EP1SZ3 EP1SZ2 EP1SZ1 EP1SZ0 EP2SZ3 EP2SZ2 EP2SZ1 EP2SZ0 H'FDE5 EPDR1 D7 D6 D5 D4 D3 D2 D1 D0 H'FDE6 FVSR1H — — — — — — N9 N8 H'FDE7 FVSR1L N7 N6 N5 N4 N3 N2 N1 N0 H'FDE9 EPDR0O D0 D7 D6 D5 D4 D3 D2 D1 H'FDEA FVSR0OH — — — — — — N9 N8 H'FDEB FVSR0OL N7 N6 N5 N4 N3 N2 N1 N0 H'FDED EPDR0I D7 D6 D5 D4 D3 D2 D1 D0 H'FDEE FVSR0IH — — — — — — N9 N8 H'FDEF FVSR0IL N7 N6 N5 N4 N3 N2 N1 N0 H'FDF0 PTTER — — — — EP2TE EP1TE EP0ITE — H'FDF1 USBIER — — BRSTE SOFE SPNDE TFE TSE SETUPE H'FDF2 USBIFR TS TF — BRSTF SOFF SPNDOF SPNDIF SETUPF H'FDF3 TSFR — — — — EP2TS EP1TS EP0ITS EP0OTS H'FDF4 TFFR — — — — EP2TF EP1TF EP0ITF EP0OTF H'FDF5 USBCSR0 DP5CNCT DP4CNCT DP3CNCT DP2CNCE EP0STOP EPIVLD EP0OTC CKSTOP H'FDF6 EPSTLR — — — — EP2STL EP1STL — EP0STL H'FDF7 EPDIR — — — — EP2DIR EP1DIR — — H'FDF8 EPRSTR — — — — EP2RST EP1RST EP0IRST — H'FDF9 DEVRSMR — — — — — — — DVR H'FDFA INTSELR0 TSELB EPIBS2 EPIBS1 EPIBS0 TSELC EPICS2 EPICS1 EPICS0 H'FDFB INTSELR1 — — — — — — DTCBE DTCCE H'FDFC HOCCR — PCSP OCDSP HOC5E HOC4E HOC3E HOC2E — H'FDFD USBCR FADSEL FONLY FNCSTP UIFRST HPLLRST HSRST FPLLRST FSRST H'FDFE UPLLCR — — — CKSEL2 CKSEL1 CKSEL0 PFSEL1 PFSEL0 TESTB TESTC TESTD TESTE TESTF TESTG TESTH H'FDFF UTESTR2 TESTA Rev. 3.00 Mar 17, 2006 page 575 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Register Address Name Bit 7 H'FE4C PCODR PC7ODR PC6ODR PC5ODR PC4ODR PC3ODR PC2ODR PC1ODR PC0ODR Ports H'FE4D PDODR PD7ODR PD6ODR PD5ODR PD4ODR PD3ODR PD2ODR PD1ODR PD0ODR H'FE4E PCDDR PC7DDR PC6DDR PC5DDR PC4DDR PC3DDR PC2DDR PC1DDR PC0DDR PCPIN PC7PIN PC6PIN PC5PIN PC4PIN PC3PIN PC2PIN PC1PIN PC0PIN H'FE4F H'FEE6 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PD7DDR PD6DDR PD5DDR PD4DDR PD3DDR PD2DDR PD1DDR PD0DDR PD7PIN PD6PIN PD5PIN PD4PIN PD3PIN PD2PIN PD1PIN PD0PIN SW IE IF CLR3 CLR2 CLR1 CLR0 IIC0 8 — — — — IRQ2F IRQ1F IRQ0F 8 — — — — — Interrupt controller — PWM 8 SCK0 System 8 IIC1 8 FRT 8 DDCSWR SWE — — — — H'FEED ISCRL — — IRQ2SCB IRQ2SCA IRQ1SCB IRQ1SCA IRQ0SCB IRQ0SCA H'FF82 PCSR — — — — — PWCKB PWCKA H'FF84 SBYCR SSBY STS2 STS1 STS0 — SCK2 SCK1 H'FF86 MSTPCRH MSTP15 MSTP14 MSTP13 MSTP12 MSTP11 MSTP10 MSTP9 MSTP8 H'FF87 MSTPCRL MSTP7 MSTP0 MSTP6 MSTP5 MSTP4 MSTP3 MSTP2 MSTP1 H'FF88 ICCR1 ICE IEIC MST TRS ACKE BBSY IRIC SCP H'FF89 ICSR1 ESTP STOP IRTR AASX AL AAS ADZ ACKB H'FF8E ICDR1 ICDR7 ICDR6 ICDR5 ICDR4 ICDR3 ICDR2 ICDR1 ICDR0 SARX SVAX6 SVAX5 SVAX4 SVAX3 SVAX2 SVAX1 SVAX0 FSX H'FF8F ICMR1 MLS WAIT CKS2 CKS1 CKS0 BC2 BC1 BC0 SAR SVA6 SVA5 SVA4 SVA3 SVA2 SVA1 SVA0 FS H'FF90 TIER ICIAE ICIBE ICICE ICIDE OCIAE OCIBE OVIE — H'FF91 TCSR ICFA ICFB ICFC ICFD OCFA OCFB OVF CCLRA H'FF92 FRCH H'FF93 FRCL 16 OCRAH OCRBH H'FF95 OCRAL H'FF96 TCR IEDGA H'FF97 TOCR ICRDMS OCRAMS ICRS OCRBL IEDGB IEDGC ICRAH OCRARH H'FF99 ICRAL OCRARL H'FF9A 8 PDDDR H'FEEC ISCRH H'FF98 Bus Width PDPIN H'FEEB ISR H'FF94 Module Name ICRBH OCRAFH Rev. 3.00 Mar 17, 2006 page 576 of 706 REJ09B0303-0300 IEDGD BUFEA BUFEB CKS1 CKS0 OCRS OEA OEB OLVLA OLVLB Appendix B Internal I/O Registers Register Address Name H'FF9B Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ICRBL Module Name Bus Width FRT 16 PWMX 8 OCRAFL H'FF9C ICRCH OCRDMH H'FF9D ICRCL OCRDML H'FF9E ICRDH H'FF9F ICRDL H'FFA0 DADRAH DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DACR TEST PWME — — OEB OEA OS CKS H'FFA1 DADRAL DA5 DA4 DA3 DA2 DA1 DA0 CFS — H'FFA6 DADRBH DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CFS REGS — REGS OVF WT/IT TME RSTS RST/NMI CKS2 CKS1 CKS0 WDT0 16 H'FFAC P1PCR P17PCR P16PCR P15PCR P14PCR P13PCR P12PCR P11PCR P10PCR Port 8 H'FFAD P2PCR P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR P21PCR P20PCR H'FFAE P3PCR P37PCR P36PCR P35PCR P34PCR P33PCR P32PCR P31PCR P30PCR H'FFB0 P1DDR P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR P11DDR P10DDR H'FFB1 P2DDR P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR P21DDR P20DDR H'FFB2 P1DR P17DR P16DR P15DR P14DR P13DR P12DR P11DR P10DR H'FFB3 P2DR P27DR P26DR P25DR P24DR P23DR P22DR P21DR P20DR H'FFB4 P3DDR P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR P31DDR P30DDR H'FFB5 P4DDR P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR P41DDR P40DDR H'FFB6 P3DR P37DR P36DR P35DR P34DR P33DR P32DR P31DR P30DR H'FFB7 P4DR P47DR P46DR P45DR P44DR P43DR P42DR P41DR P40DR H'FFB8 P5DDR — — — — — P52DDR P51DDR P50DDR H'FFB9 P6DDR P67DDR P66DDR P65DDR P64DDR P63DDR P62DDR P61DDR P60DDR — — — — — P52DR P51DR P50DR DACNTH H'FFA7 DADRBL H'FFA8 TCSR0 DACNTL TCNT0 (write) H'FFA9 TCNT0 (read) H'FFBA P5DR H'FFBB P6DR P67DR P66DR P65DR P64DR P63DR P62DR P61DR P60DR H'FFBE P7PIN P77PIN P76PIN P75PIN P74PIN P73PIN P72PIN P71PIN P70PIN H'FFC2 — — — — — IRQ2E IRQ1E IRQ0E IER Interrupts 8 Rev. 3.00 Mar 17, 2006 page 577 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Register Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Module Name Bus Width H'FFC3 STCR — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 System 8 H'FFC4 SYSCR CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME H'FFC5 MDCR EXPE — — — — — MDS1 MDS0 H'FFC6 BCR ICIS1 ICIS0 BRSTRM BRSTS1 BRSTS0 — IOS1 IOS0 TMR0, TMR1 8 TMR0, TMR1 16, 8 PWM 8 SCI0 8 H'FFC7 WSCR RAMS RAM0 ABW AST WMS1 WMS0 WC1 WC0 H'FFC8 TCR0 CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 H'FFC9 TCR1 CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 H'FFCA TCSR0 CMFB CMFA OVF ADTE OS3 OS2 OS1 OS0 H'FFCB TCSR1 CMFB CMFA OVF — OS3 OS2 OS1 OS0 H'FFCC TCORA0 H'FFCD TCORA1 H'FFCE TCORB0 H'FFCF TCORB1 H'FFD0 TCNT0 H'FFD1 TCNT1 H'FFD2 PWOERB OE15 OE14 OE13 OE12 OE11 OE10 OE9 OE8 H'FFD3 PWOERA OE7 OE6 OE5 OE4 OE3 OE2 OE1 OE0 H'FFD4 PWDPRB OS15 OS14 OS13 OS12 OS11 OS10 OS9 OS8 H'FFD5 PWDPRA OS7 OS6 OS5 OS4 OS3 OS2 OS1 OS0 H'FFD6 PWSL PWCKE PWCKS — — RS3 RS2 RS1 RS0 H'FFD7 PWDR0 to PWDR15 H'FFD8 SMR0 C/A CHR PE O/E STOP MP CKS1 CKS0 ICCR0 ICE IEIC MST TRS ACKE BBSY IRIC SCP H'FFD9 BRR0 ICSR0 H'FFDA SCR0 IIC0 SCI0 ESTP STOP IRTR AASX AL AAS ADZ ACKB IIC0 TIE RIE TE RE MPIE TEIE CKE1 CKE0 SCI0 TDRE RDRF ORER FER PER TEND MPB MPBT H'FFDB TDR0 H'FFDC SSR0 H'FFDD RDR0 H'FFDE SCMR0 — — — — SDIR SINV — SMIF ICDR0 ICDR7 ICDR6 ICDR5 ICDR4 ICDR3 ICDR2 ICDR1 ICDR0 SARX0 SVAX6 SVAX5 SVAX4 SVAX3 SVAX2 SVAX1 SVAX0 FSX H'FFDF ICMR0 MLS WAIT CKS2 CKS1 CKS0 BC2 BC1 BC0 SAR0 SVA6 SVA5 SVA4 SVA3 SVA2 SVA1 SVA0 FS H'FFE0 ADDRAH AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 H'FFE1 ADDRAL AD1 AD0 — — — — — — Rev. 3.00 Mar 17, 2006 page 578 of 706 REJ09B0303-0300 IIC0 A/D 8 Appendix B Internal I/O Registers Register Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Module Name Bus Width H'FFE2 ADDRBH AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 A/D 8 H'FFE3 ADDRBL AD1 AD0 — — — — — — H'FFE4 ADDRCH AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 H'FFE5 ADDRCL AD1 AD0 — — — — — — AD2 8 H'FFE6 ADDRDH AD9 AD8 AD7 AD6 AD5 AD4 AD3 H'FFE7 ADDRDL AD1 AD0 — — — — — — H'FFE8 ADCSR ADF ADIE ADST SCAN CKS CH2 CH1 CH0 H'FFE9 ADCR TRGS1 TRGS0 — — — — — — H'FFF0 H'FFF1 H'FFF2 H'FFF3 H'FFF4 H'FFF5 TCRX CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 TMRX TCRY CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 TMRY TCSRX CMFB CMFA OVF ICF OS3 OS2 OS1 OS0 TMRX TCSRY CMFB CMFA OVF ICIE OS3 OS2 OS1 OS0 TMRY TICRR TMRX TCORAY TMRY TICRF TMRX TCORBY TMRY TCNTX TMRX TCNTY TMRY TCORC TMRX TISR H'FFF6 TCORAX H'FFF7 TCORBX H'FFFC TCONRI — — — — — — — IS TMRY TMRX SIMOD1 H'FFFD TCONRO HOE SIMOD0 SCONE ICST HFINV VFINV HIINV VIINV VOE CLOE CBOE HOINV VOINV CLOINV CBOINV H'FFFE TCONRS TMRX/Y ISGENE HOMOD1 HOMOD0 VOMOD1 VOMOD0 CLMOD1 CLMOD0 H'FFFF SEDGR VEDG HEDG CEDG HFEDG VFEDG PREQF IHI Timer connection IVI Rev. 3.00 Mar 17, 2006 page 579 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers B.2 Address Register Selection Conditions Register Name Register Selection Conditions H'FDC0 UPRTCR MSTP1 = 0 H'FDC1 UTESTR0 USBE = 1 in STCR H'FDC2 UTESTR1 H'FDE1 EPDR2 H'FDE2 FVSR2H H'FDE3 FVSR2L H'FDE4 EPSZR1 H'FDE5 EPDR1 H'FDE6 FVSR1H H'FDE7 FVSR1L H'FDE9 EPDR0O H'FDEA FVSR0OH H'FDEB FVSR0OL H'FDED EPDR0I H'FDEE FVSR0IH H'FDEF FVSR0IL H'FDF0 PTTER H'FDF1 USBIER H'FDF2 USBIFR H'FDF3 TSFR0 H'FDF4 TFFR0 H'FDF5 USBCSR0 H'FDF6 EPSTLR H'FDF7 EPDIR H'FDF8 EPRSTR H'FDF9 DEVRSMR H'FDFA INTSELR0 H'FDFB INTSELR1 H'FDFC HOCCR H'FDFD USBCR H'FDFE UPLLCR H'FDFF UTESTR2 Rev. 3.00 Mar 17, 2006 page 580 of 706 REJ09B0303-0300 Module Name USB Appendix B Internal I/O Registers Address Register Name H'FE4C PCODR H'FE4D PDODR H'FE4E PCDDR Register Selection Conditions Module Name Port PCPIN H'FE4F PDDDR PDPIN H'FEE6 DDCSWR MSTP4 = 0 IIC0 H'FEEB ISR No conditions H'FEEC ISCRH Interrupt controller H'FEED ISCRL H'FF82 PCSR FLSHE = 0 in STCR PWM H'FF84 SBYCR FLSHE = 0 in STCR System H'FF86 MSTPCRH H'FF87 MSTPCRL H'FF88 ICCR1 MSTP3 = 0, IICE = 1 in STCR IIC1 H'FF89 ICSR1 H'FF8E ICDR1 H'FF8F MSTP3 = 0, IICE = 1 in STCR ICE = 1 in ICCR1 SARX1 ICE = 0 in ICCR1 ICMR1 ICE = 1 in ICCR1 SAR1 ICE = 0 in ICCR1 H'FF90 TIER H'FF91 TCSR H'FF92 FRCH H'FF93 FRCL H'FF94 OCRAH OCRS = 0 in TOCR OCRBH OCRS = 1 in TOCR H'FF95 OCRAL OCRS = 0 in TOCR OCRBL OCRS = 1 in TOCR H'FF96 TCR H'FF97 TOCR MSTP13 = 0 FRT Rev. 3.00 Mar 17, 2006 page 581 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Address H'FF98 Register Name ICRAH Register Selection Conditions MSTP13 = 0 OCRARH H'FF99 H'FF9A H'FF9B H'FF9C ICRS = 0 in TOCR Module Name FRT ICRS = 1 in TOCR ICRAL ICRS = 0 in TOCR OCRARL ICRS = 1 in TOCR ICRBH ICRS = 0 in TOCR OCRAFH ICRS = 1 in TOCR ICRBL ICRS = 0 in TOCR OCRAFL ICRS = 1 in TOCR ICRCH ICRS = 0 in TOCR OCRDMH ICRS = 1 in TOCR H'FF9D ICRCL ICRS = 0 in TOCR OCRDML ICRS = 1 in TOCR H'FF9E ICRDH H'FF9F ICRDL H'FFA0 DADRAH MSTP11 = 0, IICE = 1 in STCR DACR REGS=0 in DACNT/DADRB PWMX REGS=1 in DACNT/DADRB H'FFA1 DADRAL MSTP11 = 0, IICE = 1 in STCR REGS=0 in DACNT/DADRB H'FFA6 DADRBH MSTP11 = 0, IICE = 1 in STCR REGS=0 in DACNT/DADRB DACNTH REGS=1 in DACNT/DADRB H'FFA7 DADRBL REGS=0 in DACNT/DADRB H'FFA8 TCSR0 DACNTL REGS=1 in DACNT/DADRB No conditions WDT0 No conditions Ports TCNT0 (write) H'FFA9 TCNT0 (read) H'FFAC P1PCR H'FFAD P2PCR H'FFAE P3PCR H'FFB0 P1DDR Rev. 3.00 Mar 17, 2006 page 582 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Address Register Name H'FFB1 P2DDR H'FFB2 P1DR H'FFB3 P2DR H'FFB4 P3DDR H'FFB5 P4DDR H'FFB6 P3DR H'FFB7 P4DR H'FFB8 P5DDR H'FFB9 P6DDR H'FFBA P5DR H'FFBB P6DR Register Selection Conditions Module Name No conditions Ports H'FFBE P7PIN H'FFC2 IER No conditions Interrupts H'FFC3 STCR No conditions System H'FFC4 SYSCR H'FFC5 MDCR H'FFC6 BCR No conditions Bus controller H'FFC7 WSCR H'FFC8 TCR0 MSTP12 = 0 TMR0, TMR1 H'FFC9 TCR1 H'FFCA TCSR0 H'FFCB TCSR1 H'FFCC TCORA0 H'FFCD TCORA1 H'FFCE TCORB0 H'FFCF TCORB1 H'FFD0 TCNT0 H'FFD1 TCNT1 H'FFD2 PWOERB No conditions PWM H'FFD3 PWOERA H'FFD4 PWDPRB H'FFD5 PWDPRA Rev. 3.00 Mar 17, 2006 page 583 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers Address Register Name H'FFD6 PWSL H'FFD7 PWDR0 to 15 H'FFD8 Register Selection Conditions Module Name MSTP11 = 0 PWM SMR0 MSTP7 = 0, IICE = 0 in STCR SCI0 ICCR0 MSTP4 = 0, IICE = 1 in STCR IIC0 BRR0 MSTP7 = 0, IICE = 0 in STCR SCI0 ICSR0 MSTP4 = 0, IICE = 1 in STCR IIC0 H'FFDA SCR0 MSTP7 = 0 SCI0 H'FFDB TDR0 H'FFD9 H'FFDC SSR0 H'FFDD RDR0 H'FFDE SCMR0 MSTP7 = 0, IICE = 0 in STCR ICDR0 MSTP4 = 0, IICE = 1 in STCR H'FFDF ICE = 0 in ICCR0 ICMR0 ICE = 1 in ICCR0 SAR0 ICE = 0 in ICCR0 H'FFE0 ADDRAH H'FFE1 ADDRAL H'FFE2 ADDRBH H'FFE3 ADDRBL H'FFE4 ADDRCH H'FFE5 ADDRCL H'FFE6 ADDRDH H'FFE7 ADDRDL H'FFE8 ADCSR H'FFE9 ADCR H'FFF0 TCRX MSTP9 = 0 MSTP8 = 0, HIE = 0 in SYSCR TCRY H'FFF1 TCSRX MSTP8 = 0, HIE = 0 in SYSCR TCSRY H'FFF2 ICE = 1 in ICCR0 SARX0 TICRR MSTP8 = 0, HIE = 0 in SYSCR TCORAY Rev. 3.00 Mar 17, 2006 page 584 of 706 REJ09B0303-0300 IIC0 A/D TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY Appendix B Internal I/O Registers Address H'FFF3 Register Name TICRF Register Selection Conditions MSTP8 = 0, HIE = 0 in SYSCR TCORBY H'FFF4 TCNTX MSTP8 = 0, HIE = 0 in SYSCR TCNTY H'FFF5 TCORC MSTP8 = 0, HIE = 0 in SYSCR TISR H'FFF6 TCORAX H'FFF7 TCORBX H'FFFC TCONRI H'FFFD TCONRO H'FFFE TCONRS H'FFFF SEDGR MSTP8 = 0, HIE = 0 in SYSCR MSTP8 = 0, HIE = 0 in SYSCR Module Name TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY TMRX/Y = 0 in TCONRS TMRX TMRX/Y = 1 in TCONRS TMRY TMRX/Y = 0 in TCONRS TMRX Timer connection Rev. 3.00 Mar 17, 2006 page 585 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers B.3 Functions Register acronym Register name Address to which the register is mapped Name of on-chip supporting module H'FEE6 DDCSWR—DDC Switch Register IIC0 Bit numbers Bit Initial bit values 7 6 5 4 3 2 1 0 SWE SW IE IF — — — — 1 1 1 1 — — — — Initial value 0 0 0 0 Read/Write R/W R/W R/W R/(W)* DDC Mode Switch Interrupt Flag 0 Possible types of access R Read only W Write only 1 R/W Read and write No interrupt is requested when automatic format switching is executed [Clearing condition] When 0 is written in IF after reading IF = 1 Full name of bit An interrupt is requested when automatic format switching is executed [Setting condition] When a falling edge is detected on the SCL pin when SWE = 1 Descriptions of bit settings DDC Mode Switch Interrupt Enable Bit 0 Interrupt when automatic format switching is executed is disabled 1 Interrupt when automatic format switching is executed is enabled DDC Mode Switch 0 IIC channel 0 is used with the I2C bus format [Clearing conditions] • When 0 is written by software • When a falling edge is detected on the SCL pin when SWE = 1 1 IIC channel 0 is used in formatless mode [Setting condition] When 1 is written in SW after reading SW = 0 DDC Mode Switch Enable 0 Automatic switching of IIC channel 0 from formatless mode to I2C bus format is disabled 1 Automatic switching of IIC channel 0 from formatless mode to I2C bus format is enabled Note: * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 586 of 706 REJ09B0303-0300 Names of the bits. Dashes (—) indicate reserved bits. Appendix B Internal I/O Registers UPRTCR—USB Port Control Register Bit 7 6 — — H'FDC0 4 5 3 USB 2 1 0 DSPSEL2 DSPSEL1 DSPSEL0 PCNMD2 PCNMD1 PCNMD0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W Port Connection Mode Select 2 to 0 0 0 1 1 0 0 User mode 1 Digital upstream mode 0 Digital downstream mode 1 Digital upstream/downstream mode 0 Upstream transceiver/receiver monitor mode 1 Downstream transceiver/receiver monitor mode 1 — Reserved Downstream Port Select 2 to 0 0 0 1 0 Downstream port 2 selected 1 Downstream port 3 selected 0 Downstream port 4 selected 1 Downstream port 5 selected 1 — — Downstream port 1 selected UTESTR0—USB Test Register 0 UTESTR1—USB Test Register 1 H'FDC1 H'FDC2 USB USB UTESTR0 Bit 7 6 5 4 3 2 TEST15 TEST14 TEST13 TEST12 TEST11 TEST10 1 0 TEST9 TEST8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W UTESTR1 Bit 7 6 5 4 3 2 1 0 TEST7 TEST6 TEST5 TEST4 TEST3 TEST2 TEST1 TEST0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 587 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPDR2—Endpoint Data Register 2 H'FDE1 USB 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W* R/W* R/W* R/W* R/W* R/W* R/W* R/W* Bit Mediates data transfer between CPU and FIFO for each USB function endpoint host input transfer/host output transfer Note: * The EPDR2 transfer direction is determined by the endpoint direction register. EPDR2 is a write-only register when designated for host input transfer, and a read-only register when designated for host output transfer. FVSR2H—FIFO Valid Size Register 2H FVSR2L—FIFO Valid Size Register 2L H'FDE2 H'FDE3 FVSR2H Bit USB USB FVSR2L 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 — — — — — — N9 N8 N7 N6 N5 N4 N3 N2 N1 N0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Indicates number of valid data bytes in FIFO for each USB function endpoint host input/host output Rev. 3.00 Mar 17, 2006 page 588 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPSZR1—Endpoint Size Register 1 7 Bit 6 H'FDE4 5 4 3 USB 2 1 0 EP1SZ3 EP1SZ2 EP1SZ1 EP1SZ0 EP2SZ3 EP2SZ2 EP2SZ1 EP2SZ0 Initial value 0 1 0 0 0 1 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Specifies number of FIFO bytes used Bits 7 to 4 EP1 FIFO size Bits 3 to 0 EP2 FIFO size EPnSZ3 EPnSZ2 EPnSZ1 EPnSZ0 0 0 0 FIFO size = 0 bytes (settable for EP2 only) 1 Setting prohibited 0 Setting prohibited 1 Setting prohibited 0 FIFO size = 16 bytes 1 FIFO size = 32 bytes (settable for EP1 only) 1 0 Setting prohibited 1 Setting prohibited — — Setting prohibited 1 1 0 — 1 Operating Mode 0 (Initial value) n = 1, 2 EPDR1—Endpoint Data Register 1 Bit H'FDE5 USB 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Mediates data transfer between CPU and FIFO for each USB function endpoint host input transfer/host output transfer Rev. 3.00 Mar 17, 2006 page 589 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers FVSR1H—FIFO Valid Size Register 1H FVSR1L—FIFO Valid Size Register 1H H'FDE6 H'FDE7 USB USB FVSR1H Bit FVSR1L 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 — — — — — — N9 N8 N7 N6 N5 N4 N3 N2 N1 N0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Indicates number of valid data bytes in FIFO for each USB function endpoint host input/host output EPDR0O—Endpoint Data Register 0O Bit H'FDE9 USB 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R Mediates data transfer between CPU and FIFO for each USB function endpoint host input transfer/host output transfer FVSR0OH—FIFO Valid Size Register 0OH FVSR0OL—FIFO Valid Size Register 0OL H'FDEA H'FDEB FVSR0OH USB USB FVSR0OL 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 — — — — — — N9 N8 N7 N6 N5 N4 N3 N2 N1 N0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Bit Indicates number of valid data bytes in FIFO for each USB function endpoint host input/host output Rev. 3.00 Mar 17, 2006 page 590 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPDR0I—Endpoint Data Register 0I Bit H'FDED USB 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Mediates data transfer between CPU and FIFO for each USB function endpoint host input transfer/host output transfer FVSR0IH—FIFO Valid Size Register 0IH FVSR0IL—FIFO Valid Size Register 0IL H'FDEE H'FDEF FVSR0IH USB USB FVSR0IL 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 — — — — — — N9 N8 N7 N6 N5 N4 N3 N2 N1 N0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Bit Indicates number of valid data bytes in FIFO for each USB function endpoint host input/host output Rev. 3.00 Mar 17, 2006 page 591 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PTTER—Packet Transmit Enable Register H'FDF0 USB 7 6 5 4 3 2 1 0 — — — — EP2TE EP1TE EP0ITE — Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/(W)* R/(W)* R/(W)* R Bit Endpoint 0I Packet Transmit Enable 0 Initial set value (1) [1 write] Endpoint 0 IN-FIFO FVSR0I is updated Endpoint 1 Packet Transmit Enable 0 Initial set value (1) [1 write] Endpoint 1 IN-FIFO FVSR1 is updated Endpoint 2 Packet Transmit Enable 0 Initial set value (1) [1 write] Endpoint 2 IN-FIFO FVSR2 is updated Note: * Only 1 can be written. Rev. 3.00 Mar 17, 2006 page 592 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers USBIER—USB Interrupt Enable Register H'FDF1 USB 7 6 5 4 3 2 1 0 — — BRSTE SOFE SPNDE TFE TSE SETUPE Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W Bit Setup Interrupt Enable 0 USB function setup interrupts disabled 1 USB function setup interrupts enabled Transfer Successful Interrupt Enable 0 USB function transfer successful interrupts disabled 1 USB function transfer successful interrupts enabled Transfer Failed Interrupt Enable 0 USB function transfer failed interrupts disabled 1 USB function transfer failed interrupts enabled Suspend Interrupt Enable 0 USB function suspend OUT interrupts and suspend IN interrupts disabled 1 USB function suspend OUT interrupts and suspend IN interrupts enabled SOF Interrupt Enable 0 USB function SOF interrupts disabled 1 USB function SOF interrupts enabled Bus Reset Interrupt Enable 0 USB function bus reset interrupts disabled 1 USB function bus reset interrupts enabled Rev. 3.00 Mar 17, 2006 page 593 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers USBIFR—USB Interrupt Flag Register Bit H'FDF2 7 6 5 4 3 TS TF — BRSTF SOFF USB 2 1 0 SPNDOF SPNDIF SETUPF Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* Setup Interrupt Flag 0 [Clearing condition] When 0 is written in SETUPF after reading SETUPF = 1 1 [Setting condition] When USB function endpoint 0 receives SETUP token Suspend IN Interrupt Flag 0 [Clearing condition] When 0 is written in SPNDIF after reading SPNDIF = 1 1 [Setting condition] When USB function switches from normal state to suspend state Suspend OUT Interrupt Flag 0 [Clearing condition] When 0 is written in SPNDOF after reading SPNDOF = 1 1 [Setting condition] When USB function switches from suspend state to normal state SOF Interrupt Flag 0 [Clearing condition] When 0 is written in SOFF after reading SOFF = 1 1 [Setting condition] When USB function detects SOF (Start of Frame) Bus Reset Interrupt Flag 0 [Clearing condition] When 0 is written in BRSTF after reading BRSTF = 1 1 [Setting condition] When USB function detects a bus reset from upstream Transfer Failed Interrupt Status 0 All bits in transfer fail flag register (TFFR) are 0 1 At least one bit in transfer fail flag register (TFFR) is 1 Transfer Successful Interrupt Status 0 All bits in transfer success flag register (TSFR) are 0 1 At least one bit in transfer success flag register (TSFR) is 1 Note: * Only 0 can be written, after reading 1, to clear the flag. Rev. 3.00 Mar 17, 2006 page 594 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TSFR—Transfer Success Flag Register Bit H'FDF3 USB 7 6 5 4 3 2 — — — — EP2TS EP1TS 1 0 EP0ITS EP0OTS Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/(W)* R/(W)* R/(W)* R/(W)* Endpoint 0 Host Output Transfer Success Flag 0 Endpoint 0 is in host output transfer standby state [Clearing conditions] • When 0 is written in EP0OTS after reading EP0OTS = 1 • When endpoint 0 receives a SETUP token 1 Endpoint 0 host output transfer (OUT transaction or SETUP transaction) has ended normally [Setting conditions] • ACK handshake established after OUT token reception and data transfer (ACK transmission) • When command received after SETUP token reception requires processing by the slave CPU Endpoint 0 Host Input Transfer Success Flag 0 Endpoint 0 is in host input transfer standby state [Clearing conditions] • When 0 is written in EP0ITS after reading EP0ITS = 1 • When endpoint 0 receives a SETUP token 1 Endpoint 0 host input transfer (IN transaction) has ended normally [Setting condition] ACK handshake established after IN token reception and data transfer (ACK reception) Endpoint 1 Transfer Success Flag 0 Endpoint 1 is in transfer standby state [Clearing condition] When 0 is written in EP1TS after reading EP1TS = 1 1 Endpoint 1 host input transfer (IN transaction) has ended normally [Setting condition] ACK handshake established after IN token reception and data transfer (ACK reception) Endpoint 2 Transfer Success Flag 0 Endpoint 2 is in transfer standby state) [Clearing condition] When 0 is written in EP2TS after reading EP2TS = 1 1 Endpoint 2 host input transfer (IN transaction) or host output transfer (OUT transaction) has ended normally [Setting conditions] • ACK handshake established after IN token reception and data transfer (ACK reception) • ACK handshake established after OUT token reception and data transfer (ACK transmission) Note: * Only 0 can be written, after reading 1, to clear the flag. Rev. 3.00 Mar 17, 2006 page 595 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TFFR—Transfer Fail Flag Register Bit H'FDF4 USB 7 6 5 4 3 2 — — — — EP2TF EP1TF 1 0 EP0ITF EP0OTF Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/(W)* R/(W)* R/(W)* R/(W)* Endpoint 0 Host Output Transfer Fail Flag 0 Endpoint 0 is in host output transfer standby state [Clearing conditions] • When 0 is written in EP0OTF after reading EP0OTF = 1 • When endpoint 0 receives a SETUP token 1 Endpoint 0 host output transfer (OUT transaction or SETUP transaction) has ended abnormally [Setting conditions] • Data transfer not possible due to FIFO full condition after OUT token reception (NAK transmission) • Data transfer not possible because EP0OTC = 1 after OUT token reception (NAK transmission) • Communication error after OUT token reception • When command received after SETUP token reception can be processed within the USB function core Endpoint 0 Host Input Transfer Fail Flag 0 Endpoint 0 is in host input transfer standby state [Clearing conditions] • When 0 is written in EP0ITF after reading EP0ITF = 1 • When endpoint 0 receives a SETUP token 1 Endpoint 0 host input transfer (IN transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception (NAK transmission) Endpoint 1 Transfer Fail Flag 0 Endpoint 1 is in transfer standby state [Clearing condition] When 0 is written in EP1TF after reading EP1TF = 1 1 Endpoint 1 host input transfer (IN transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception (NAK transmission) Endpoint 2 Transfer Fail Flag 0 Endpoint 2 is in transfer standby state [Clearing condition] When 0 is written to EP2TF after reading EP2TF = 1 1 Endpoint 2 host input transfer (IN transaction) or host output transfer (OUT transaction) has ended abnormally [Setting conditions] • ACK handshake not established after IN token reception and data transfer • Data transfer not possible due to FIFO empty condition after IN token reception (NAK transmission) • Data reception not possible due to FIFO full condition after OUT token reception (NAK transmission) • DATA0/DATA1 PID toggle error after OUT token reception Note: * Only 0 can be written, after reading 1, to clear the flag. Rev. 3.00 Mar 17, 2006 page 596 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers USBCSR0—USB Control/Status Register 0 7 Bit 6 H'FDF5 5 4 3 USB 2 DP5CNCT DP4CNCT DP3CNCT DP2CNCT EP0STOP EPIVLD 1 0 EP0OTC CKSTOP Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/W R/W R/W R/W Clock Stop 0 Clock is supplied to USB function [Clearing conditions] • System reset • Function soft reset • Suspend OUT interrupt flag setting 1 Clock supply to USB function is stopped [Setting condition] When 1 is written in CKSTOP after reading CKSTOP = 0 Endpoint 0O Transfer Control 0 EP0 OUT-FIFO writing stopped • Subsequent writes to EP0 OUT-FIFO are invalid [Clearing conditions] • System reset • Function soft reset • Command data reception in SETUP transaction (EP0OTS flag setting) 1 EP0 OUT-FIFO operational [Setting conditions] • SETUP token reception • When 1 is written in EP0OTC after reading EP0OTC = 0 Endpoint Information Valid 0 Endpoint information (EPINFO) has not been set [Clearing conditions] • System reset • Function soft reset 1 Endpoint information (EPINFO) has been set Endpoint 0 Stop 0 EP0 OUT-FIFO, IN-FIFO operational [Clearing conditions] • System reset • Function soft reset 1 EP0 OUT-FIFO reading stopped • FVSR0O contents are not changed by an EPDR0O read EP0 IN-FIFO writing and transfer stopped • FIFO contents are not changed by an EPDR0I write • FVSR0I contents are not changed by setting EP0IPTE Downstream Port Connect 5 to 2 0 Cable is not connected to downstream port [Clearing conditions] • System reset • Downstream port disconnect • USB hub upstream port disconnect (Total downstream disconnect by software in reconnect process) 1 Cable is connected to downstream port, and power is being supplied [Setting condition] Downstream port connect Rev. 3.00 Mar 17, 2006 page 597 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPSTLR—Endpoint Stall Register H'FDF6 7 6 5 4 — — — — Initial value 0 0 0 0 0 Read/Write R R R R R/W Bit 3 USB 2 1 0 — EP0STL 0 0 0 R/W R R/W EP2STL EP1STL Endpoint 0 Stall 0 Endpoint 0 is operational [Clearing condition] When endpoint 0 receives a SETUP token 1 Endpoint 0 is in stall state [Setting condition] When 1 is written in EP0STL after reading EP0STL = 0 Endpoint 1 Stall 0 Endpoint 1 is operational 1 Endpoint 1 is in stall state Endpoint 2 Stall 0 Endpoint 2 is operational 1 Endpoint 2 is in stall state Rev. 3.00 Mar 17, 2006 page 598 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPDIR—Endpoint Direction Register Bit H'FDF7 7 6 5 4 3 USB 2 1 0 — — — — — — Initial value 1 1 1 1 1 1 0 0 Read/Write R R R R R/W R/W R R EP2DIR EP1DIR Endpoint 1 Data Transfer Direction Control Flag 0 Setting prohibited 1 Endpoint 1 is designated for host input transfer Endpoint 2 Data Transfer Direction Control Flag 0 Endpoint 2 is designated for host output transfer 1 Endpoint 2 is designated for host input transfer Rev. 3.00 Mar 17, 2006 page 599 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers EPRSTR—Endpoint Reset Register H'FDF8 USB 7 6 5 4 — — — — Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R/(W)* R/(W)* R/(W)* R Bit 3 2 1 EP2RST EP1RST EP0IRST 0 — Endpoint 0I Reset 0 Initial set value (1) [1 write] FVSR0I is initialized to H'0010 Endpoint 1 Reset 0 Initial set value (1) [1 write] EP1 FIFO size = 16 bytes: FVSR1 is initialized to H'0010 EP1 FIFO size = 32 bytes: FVSR1 is initialized to H'0020 Endpoint 2 Reset 0 Initial set value (1) [1 write] EP2DIR = 0: FVSR2 is initialized to H'0000 EP2DIR = 1: FVSR2 is initialized to H'0010 Note: * Only 1 can be written. Rev. 3.00 Mar 17, 2006 page 600 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers DEVRSMR—Device Resume Register H'FDF9 USB 7 6 5 4 3 2 1 0 — — — — — — — DVR Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R/(W)* Bit Device Resume (DVR) 0 (Initial value) (1) [1 write] Suspend state is cleared (remote wakeup) Note: * Only 1 can be written. Rev. 3.00 Mar 17, 2006 page 601 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers INTSELR0—Interrupt Source Select Register 0 Bit H'FDFA USB 7 6 5 4 3 2 1 0 TSELB EPIBS2 EPIBS1 EPIBS0 TSELC EPICS2 EPICS1 EPICS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Interrupt C Endpoint Select 2 to 0 0 0 1 0 Initial set value 1 Endpoint 1 selected 0 Endpoint 2 selected 1 Setting prohibited 1 — — Setting prohibited Transfer Select C 0 USBIC is requested by a TS interrupt; the endpoint constituting the TS interrupt source is specified by bits EPICS2 to EPICS0 1 USBIC is requested by a TF interrupt; the endpoint constituting the TF interrupt source is specified by bits EPICS2 to EPICS0 Interrupt B Endpoint Select 2 to 0 0 0 1 0 Initial set value 1 Endpoint 1 selected 0 Endpoint 2 selected 1 Setting prohibited 1 — — Setting prohibited Transfer Select B 0 USBIB is requested by a TS interrupt; the endpoint constituting the TS interrupt source is specified by bits EPIBS2 to EPIBS0 1 USBIB is requested by a TF interrupt; the endpoint constituting the TF interrupt source is specified by bits EPIBS2 to EPIBS0 Rev. 3.00 Mar 17, 2006 page 602 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers INTSELR1—Interrupt Source Select Register 1 H'FDFB USB 7 6 5 4 3 2 1 0 — — — — — — DTCBE DTCCE Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R/W R/W Bit Note: Do not write 1 to the bits in this register. Rev. 3.00 Mar 17, 2006 page 603 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers HOCCR—Hub Overcurrent Control Register H'FDFC USB 7 6 5 4 3 2 1 0 — — PCSP OCDSP HOC5E HOC4E HOC3E HOC2E Bit Initial value 0 0 0 0 0 0 0 0 Read/Write R R R/W R/W R/W R/W R/W R/W Overcurrent Detection Control Enable 2 0 Pins ENP2 and OCP2 are general ports (PC4, PC0) 1 Pins ENP2 and OCP2 have output enable and overcurrent detection functions Overcurrent Detection Control Enable 3 0 Pins ENP3 and OCP3 are general ports (PC5, PC1) 1 Pins ENP3 and OCP3 have output enable and overcurrent detection functions Overcurrent Detection Control Enable 4 0 Pins ENP4 and OCP4 are general ports (PC6, PC2) 1 Pins ENP4 and OCP4 have output enable and overcurrent detection functions Overcurrent Detection Control Enable 5 0 Pins ENP5 and OCP5 are general ports (PC7, PC3) 1 Pins ENP5 and OCP5 have output enable and overcurrent detection functions Overcurrent Detection Polarity 0 Power supply control IC outputs low level in case of overcurrent detection 1 Power supply control IC outputs high level in case of overcurrent detection Power Supply Enable Control Polarity 0 Power supply control IC requires low-level input for enabling 1 Power supply control IC requires high-level input for enabling Rev. 3.00 Mar 17, 2006 page 604 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers USBCR—USB Control Register 7 Bit H'FDFD 6 5 4 USB 2 3 1 0 FADSEL FONLY FNCSTP UIFRST HPLLRST HSRST FPLLRST FSRST Initial value 0 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Function Block Internal State Soft Reset 0 Internal state of USB function block is set to operational state 1 Internal state of USB function block is set to reset state (excluding DPLL) Function Block PLL Soft Reset 0 Function DPLL is placed in operational state 1 Function DPLL is placed in reset state Hub Block Internal State Soft Reset 0 Internal state of USB hub block is set to operational state 1 Internal state of USB hub block is set to reset state (excluding DPLL) Hub Block PLL Soft Reset 0 Hub DPLL is placed in operational state 1 Hub DPLL is placed in reset state USB Interface Soft Reset 0 EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 are placed in operational state 1 EPSZR1, USBIER, EPDIR, INTSELR0, and INTSELR1 are placed in reset state USB Function Stop/Suspend 0 For USB function block, USB hub downstream port 1 internal connection is set to connected state 1 For USB function block, USB hub downstream port 1 internal connection is set to disconnected state, and power-down state is set USB Function Select 0 USB function block is connected internally to USB hub downstream port 1; USB hub block is enabled 1 USB function block is directly connected to upstream port; USB hub block is disabled USB Function I/O Analog/Digital Select 0 USD+ and USD– pins are used for USB function block data input/output 1 USB function block data input/output is implemented by multiplexing Philips transceiver/receiver (PIDUSB11A) compatible control input/output with port C pins Rev. 3.00 Mar 17, 2006 page 605 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers UPLLCR—USB PLL Control Register Bit 7 6 5 H'FDFE 4 3 USB 2 1 0 — — — Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R/W R/W R/W R/W R/W CKSEL2 CKSEL1 CKSEL0 PFSEL1 PFSEL0 PLL Frequency Select 0 1 0 PLL input clock is 8 MHz 1 PLL input clock is 12 MHz 0 PLL input clock is 16 MHz 1 PLL input clock is 20 MHz Clock Source Select 2 to 0 0 0 0 PLL operation halted, clock input halted — — PLL operation halted, clock input halted 1 0 1 0 Setting prohibited 1 PLL operation halted USB clock pulse generator (XTAL12: 48 MHz) used directly instead of PLL output 0 PLL operates with system clock pulse generator (XTAL) as clock source 1 PLL operates with USB clock pulse generator (XTAL12) as clock source UTESTR2—USB Test Register 2 H'FDFF USB UTESTR2 Bit 7 6 5 4 3 2 1 0 TESTA TESTB TESTC TESTD TESTE TESTF TESTG TESTH Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Rev. 3.00 Mar 17, 2006 page 606 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PCODR—Port C Data Output Register Bit 7 6 H'FE4C 5 4 Port C 3 2 1 0 PC7ODR PC6ODR PC5ODR PC4ODR PC3ODR PC2ODR PC1ODR PC0ODR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port C pins PDODR—Port D Data Output Register Bit 7 6 H'FE4D 5 4 Port D 3 2 1 0 PD7ODR PD6ODR PD5ODR PD4ODR PD3ODR PD2ODR PD1ODR PD0ODR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port D pins PCDDR—Port C Data Direction Register Bit 7 6 5 H'FE4E 4 3 Port C 2 1 0 PC7DDR PC6DDR PC5DDR PC4DDR PC3DDR PC2DDR PC1DDR PC0DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port C pins Rev. 3.00 Mar 17, 2006 page 607 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PCPIN—Port C Input Data Register H'FE4E Port C 7 6 5 4 3 2 1 0 PC7PIN PC6PIN PC5PIN PC4PIN PC3PIN PC2PIN PC1PIN PC0PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Bit Port C pin states Note: * Determined by the state of pins PC7 to PC0. PDDDR—Port D Data Direction Register Bit 7 6 5 H'FE4F 4 3 Port D 2 1 0 PD7DDR PD6DDR PD5DDR PD4DDR PD3DDR PD2DDR PD1DDR PD0DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port D pins PDPIN—Port D Input Data Register H'FE4F Port D 7 6 5 4 3 2 1 0 PD7PIN PD6PIN PD5PIN PD4PIN PD3PIN PD2PIN PD1PIN PD0PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Bit Port D pin states Note: * Determined by the state of pins PD7 to PD0. Rev. 3.00 Mar 17, 2006 page 608 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers DDCSWR—DDC Switch Register Bit H'FEE6 IIC0 7 6 5 4 3 2 1 0 SWE SW IE IF CLR3 CLR2 CLR1 CLR0 Initial value 0 0 0 0 1 1 Read/Write R/W R/W R/W R/(W)*1 W*2 W*2 1 1 W*2 W*2 IIC Clear 3 to 0 0 0 — — Setting prohibited 1 0 1 0 Setting prohibited 1 IIC0 internal latch clearance 0 IIC1 internal latch clearance 1 IIC0 and IIC1 internal latch clearance 1 — — — Invalid setting DDC Mode Switch Interrupt Flag 0 No interrupt is requested when automatic format switching is executed [Clearing condition] When 0 is written in IF after reading IF = 1 1 An interrupt is requested when automatic format switching is executed [Setting condition] When a falling edge is detected on the SCL pin when SWE = 1 DDC Mode Switch Interrupt Enable Bit 0 Interrupt when automatic format switching is executed is disabled 1 Interrupt when automatic format switching is executed is enabled DDC Mode Switch 0 IIC channel 0 is used with the I2C bus format [Clearing conditions] • When 0 is written by software • When a falling edge is detected on the SCL pin when SWE = 1 1 IIC channel 0 is used in formatless mode [Setting condition] When 1 is written in SW after reading SW = 0 DDC Mode Switch Enable 0 Automatic switching of IIC channel 0 from formatless mode to I2C bus format is disabled 1 Automatic switching of IIC channel 0 from formatless mode to I2C bus format is enabled Notes: 1. Only 0 can be written, to clear the flag. 2. Always read as 1. Rev. 3.00 Mar 17, 2006 page 609 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers ISR—IRQ Status Register Bit H'FEEB Interrupt Controller 7 6 5 4 3 2 1 0 — — — — — IRQ2F IRQ1F IRQ0F Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R/(W)* R/(W)* R/(W)* IRQ2 to IRQ0 Flags 0 [Clearing conditions] • When 0 is written in IRQnF after reading IRQnF = 1 • When interrupt exception handling is executed while low-level detection is set (IRQnSCB = IRQnSCA = 0) and IRQn input is high • When IRQn interrupt exception handling is executed while falling, rising, or both-edge detection is set (IRQnSCB = 1 or IRQnSCA = 1) 1 [Setting conditions] • When IRQn input goes low while low-level detection is set (IRQnSCB = IRQnSCA = 0) • When a falling edge occurs in IRQn input while falling edge detection is set (IRQnSCB = 0, IRQnSCA = 1) • When a rising edge occurs in IRQn input while rising edge detection is set (IRQnSCB = 1, IRQnSCA = 0) • When a falling or rising edge occurs in IRQn input while both-edge detection is set (IRQnSCB = IRQnSCA = 1) Notes: n = 2 to 0 * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 610 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers ISCRH—IRQ Sense Control Register H ISCRL—IRQ Sense Control Register L H'FEEC H'FEED Interrupt Controller Interrupt Controller ISCRH 15 14 13 12 11 10 9 8 — — — — — — — — Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 2 1 0 Bit Reserved ISCRL Bit 7 6 5 4 3 IRQ2SCB IRQ2SCA IRQ1SCB IRQ1SCA IRQ0SCB IRQ0SCA — — Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W IRQ2 to IRQ0 Sense Control A and B ISCRL bits 5 to 0 Description IRQ2SCB to IRQ0SCB IRQ2SCA to IRQ0SCA 0 0 Interrupt request generated by low level of IRQ2–IRQ0 input 1 Interrupt request generated by falling edge of IRQ2–IRQ0 input 0 Interrupt request generated by rising edge of IRQ2–IRQ0 input 1 Interrupt request generated by rising and falling edges of IRQ2–IRQ0 input 1 Rev. 3.00 Mar 17, 2006 page 611 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PCSR—Peripheral Clock Select Register H'FF82 PWM 7 6 5 4 3 — — — — — Initial value 0 0 0 0 0 0 0 0 Read/Write — — — — — R/W R/W R/W Bit 2 1 PWCKB PWCKA PWM Clock Select PWSL Bit 7 PCSR Bit 6 Bit 2 Bit 1 Description PWCKE PWCKS PWCKB PWCKA 0 — — — Clock input stopped 1 0 — — φ (system clock) selected 1 0 0 φ/2 selected 1 φ/4 selected 0 φ/8 selected 1 φ/16 selected 1 Rev. 3.00 Mar 17, 2006 page 612 of 706 REJ09B0303-0300 0 — Appendix B Internal I/O Registers SBYCR—Standby Control Register H'FF84 System 7 6 5 4 3 2 1 0 SSBY STS2 STS1 STS0 — SCK2 SCK1 SCK0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W — R/W R/W R/W Bit System Clock Select 2 to 0 0 0 1 1 0 0 Bus master is in high-speed mode 1 Medium-speed clock = φ/2 0 Medium-speed clock = φ/4 1 Medium-speed clock = φ/8 0 Medium-speed clock = φ/16 1 Medium-speed clock = φ/32 1 — — Standby Timer Select 2 to 0 0 0 1 1 0 1 0 Standby time = 8,192 states 1 Standby time = 16,384 states 0 Standby time = 32,768 states 1 Standby time = 65,536 states 0 Standby time = 131,072 states 1 Standby time = 262,144 states 0 Reserved 1 Standby time = 16 states Software Standby 0 Transition to sleep mode on execution of SLEEP instruction in high-speed mode or medium-speed mode 1 Transition to software standby mode on execution of SLEEP instruction in high-speed mode or medium-speed mode Rev. 3.00 Mar 17, 2006 page 613 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers MSTPCRH—Module Stop Control Register H MSTPCRL—Module Stop Control Register L H'FF86 H'FF87 System System MSTPCRH 7 Bit 6 5 4 3 MSTPCRL 2 1 0 7 6 5 4 3 2 1 0 MSTP15 MSTP14 MSTP13 MSTP12 MSTP11 MSTP10 MSTP9 MSTP8 MSTP7 MSTP6 MSTP5 MSTP4 MSTP3 MSTP2 MSTP1 MSTP0 Initial value 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Module Stop 0 Module stop mode cleared 1 Module stop mode set The correspondence between MSTPCR bits and on-chip supporting modules is shown below. Register Bit MSTPCRH MSTP15* — MSTP14* — MSTP13 16-bit free-running timer (FRT) MSTP12 8-bit timers (TMR0, TMR1) MSTP11 8-bit PWM timer (PWM), 14-bit PWM timer (PWMX) MSTP10* — MSTP9 A/D converter MSTP8 8-bit timers (TMRX, TMRY), timer connection MSTP7 Serial communication interface 0 (SCI0) MSTP6* — MSTP5* — MSTP4 I2C bus interface (IIC) channel 0 MSTP3 I2C bus interface (IIC) channel 1 MSTP2* — MSTP1 Universal serial bus interface (USB) MSTP0* — MSTPCRL Module Note: * Bits 15, 14, 10, 6, 5, 2, and 0 can be read and written but must always be set to 1. Rev. 3.00 Mar 17, 2006 page 614 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICCR1—I C Bus Control Register 1 Bit H'FF88 IIC1 7 6 5 4 3 2 1 0 ICE IEIC MST TRS ACKE BBSY IRIC SCP Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/(W)* W Start Condition/Stop Condition Prohibit 0 Writing issues a start or stop condition, in combination with the BBSY flag 1 Reading always returns a value of 1; writing is invalid I2C Bus Interface Interrupt Request Flag 0 Waiting for transfer, or transfer in progress 1 Interrupt requested Note: For the clearing and setting conditions, see section 16.2.5, I2C Bus Control Register (ICCR). Bus Busy 0 Bus is free [Clearing condition] When a stop condition is detected 1 Bus is busy [Setting condition] When a start condition is detected Acknowledge Bit Judgement Select 0 Acknowledge bit is ignored and continuous transfer is performed 1 If acknowledge bit is 1, continuous transfer is interrupted Master/Slave Select (MST), Transmit/Receive Select (TRS) 0 1 0 Slave receive mode 1 Slave transmit mode 0 Master receive mode 1 Master transmit mode Note: For details see section 16.2.5, I2C Bus Control Register (ICCR). I2C Bus Interface Interrupt Enable I2C 0 Interrupt requests disabled 1 Interrupt requests enabled Bus Interface Enable 0 I2C bus interface module disabled, with SCL and SDA signal pins set to port function SAR and SARX can be accessed 1 I2C bus interface module enabled for transfer operations (pins SCL and SDA are driving the bus) ICMR and ICDR can be accessed Note: * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 615 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICSR1—I C Bus Status Register 1 Bit H'FF89 IIC1 7 6 5 4 3 2 1 0 ESTP STOP IRTR AASX AL AAS ADZ ACKB Initial value 0 0 Read/Write R/(W)*1 0 0 0 0 0 1 1 1 1 1 * * * * * R/(W) R/(W) R/(W) R/(W) R/(W)*1 R/(W) 0 R/W Acknowledge Bit 0 Receive mode: 0 is output at acknowledge output timing Transmit mode: indicates that the receiving device has acknowledged the data (0 value) 1 Receive mode: 1 is output at acknowledge output timing Transmit mode: indicates that the receiving device has not acknowledged the data (1 value) General Call Address Recognition Flag*2 0 General call address not recognized 1 General call address recognized Slave Address Recognition Flag*2 0 Slave address or general call address not recognized 1 Slave address or general call address recognized Arbitration Lost Flag*2 0 Bus arbitration won 1 Bus arbitration lost Second Slave Address Recognition Flag*2 I2C 0 Second slave address not recognized 1 Second slave address recognized Bus Interface Continuous Transmission/Reception Interrupt Request Flag*2 0 Waiting for transfer, or transfer in progress 1 Continuous transfer state Normal Stop Condition Detection Flag*2 0 No normal stop condition 1 In I2C bus format slave mode: Normal stop condition detected In other modes: No meaning Error Stop Condition Detection Flag*2 0 No error stop condition 1 In I2C bus format slave mode: Error stop condition detected In other modes: No meaning Notes: 1. Only 0 can be written, to clear the flag. 2. For the clearing and setting conditions, see section 16.2.6, I2C Bus Status Register (ICSR). Rev. 3.00 Mar 17, 2006 page 616 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICDR1—I C Bus Data Register 1 Bit H'FF8E IIC1 7 6 5 4 3 2 1 0 ICDR7 ICDR6 ICDR5 ICDR4 ICDR3 ICDR2 ICDR1 ICDR0 Initial value — — — — — — — — Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 • ICDRR Bit ICDRR7 ICDRR6 ICDRR5 ICDRR4 ICDRR3 ICDRR2 ICDRR1 ICDRR0 Initial value — — — — — — — — Read/Write R R R R R R R R 7 6 5 4 3 2 1 0 • ICDRS Bit ICDRS7 ICDRS6 ICDRS5 ICDRS4 ICDRS3 ICDRS2 ICDRS1 ICDRS0 Initial value — — — — — — — — Read/Write — — — — — — — — 7 6 5 4 3 2 1 0 • ICDRT Bit ICDRT7 ICDRT6 ICDRT5 ICDRT4 ICDRT3 ICDRT2 ICDRT1 ICDRT0 Initial value — — — — — — — — Read/Write W W W W W W W W — — TDRE RDRF • TDRE, RDRF (internal flags) Bit Initial value 0 0 Read/Write — — Note: For details see section 16.2.1, I2C Bus Data Register (ICDR). Rev. 3.00 Mar 17, 2006 page 617 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SARX—Second Slave Address Register 1 Bit H'FF8E IIC1 7 6 5 4 3 2 1 0 SVAX6 SVAX5 SVAX4 SVAX3 SVAX2 SVAX1 SVAX0 FSX Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Second Slave Address Format Select X DDCSWR Bit 6 SAR Bit 0 SARX Bit 0 SW FS FSX 0 0 0 I2C bus format • SAR and SARX slave addresses recognized 1 I2C bus format • SAR slave address recognized • SARX slave address ignored 0 I2C bus format • SAR slave address ignored • SARX slave address recognized 1 Synchronous serial format • SAR and SARX slave addresses ignored 0 Formatless mode (start/stop conditions not detected) • Acknowledge bit present 1 1 0 1 1 0 1 Operating Mode Formatless mode* (start/stop conditions not detected) • No acknowledge bit Note: * Do not select this mode when automatic switching to the I2C bus format is performed by means of a DDCSWR setting. Rev. 3.00 Mar 17, 2006 page 618 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SAR—Slave Address Register H'FF8F IIC1 7 6 5 4 3 2 1 0 SVA6 SVA5 SVA4 SVA3 SVA2 SVA1 SVA0 FS Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Slave Address Format Select DDCSWR Bit 6 SAR Bit 0 SARX Bit 0 SW FS FSX 0 0 0 I2C bus format • SAR and SARX slave addresses recognized 1 I2C bus format • SAR slave address recognized • SARX slave address ignored 0 I2C bus format • SAR slave address ignored • SARX slave address recognized 1 Synchronous serial format • SAR and SARX slave addresses ignored 0 Formatless mode (start/stop conditions not detected) • Acknowledge bit present 1 1 0 1 1 0 1 Operating Mode Formatless mode* (start/stop conditions not detected) • No acknowledge bit Note: * Do not select this mode when automatic switching to the I2C bus format is performed by means of a DDCSWR setting. Rev. 3.00 Mar 17, 2006 page 619 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICMR1—I C Bus Mode Register 1 H'FF8F IIC1 7 6 5 4 3 2 1 0 MLS WAIT CKS2 CKS1 CKS0 BC2 BC1 BC0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Bit Counter BC2 BC1 BC0 0 0 0 1 0 1 0 1 0 1 1 1 0 1 Synchronous Serial Format 8 1 2 3 4 5 6 7 Transfer Clock Select IICX 0 CKS2 0 CKS1 0 1 1 0 1 1 0 0 1 1 0 1 CKS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Clock φ/28 φ/40 φ/48 φ/64 φ/80 φ/100 φ/112 φ/128 φ/56 φ/80 φ/96 φ/128 φ/160 φ/200 φ/224 φ/256 Wait Insertion Bit 0 Data and acknowledge transferred consecutively 1 Wait inserted between data and acknowledge MSB-First/LSB-First Select* 0 MSB-first 1 LSB-first Note: * Do not set this bit to 1 when using the I2C bus format. Rev. 3.00 Mar 17, 2006 page 620 of 706 REJ09B0303-0300 I2C Bus Format 9 2 3 4 5 6 7 8 Appendix B Internal I/O Registers TIER—Timer Interrupt Enable Register H'FF90 FRT 7 6 5 4 3 2 1 0 ICIAE ICIBE ICICE ICIDE OCIAE OCIBE OVIE — Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/W — Bit Timer Overflow Interrupt Enable 0 OVF interrupt request (FOVI) is disabled 1 OVF interrupt request (FOVI) is enabled Output Compare Interrupt B Enable 0 OCFB interrupt request (OCIB) is disabled 1 OCFB interrupt request (OCIB) is enabled Output Compare Interrupt A Enable 0 OCFA interrupt request (OCIA) is disabled 1 OCFA interrupt request (OCIA) is enabled Input Capture Interrupt D Enable 0 ICFD interrupt request (ICID) is disabled 1 ICFD interrupt request (ICID) is enabled Input Capture Interrupt C Enable 0 ICFC interrupt request (ICIC) is disabled 1 ICFC interrupt request (ICIC) is enabled Input Capture Interrupt B Enable 0 ICFB interrupt request (ICIB) is disabled 1 ICFB interrupt request (ICIB) is enabled Input Capture Interrupt A Enable 0 ICFA interrupt request (ICIA) is disabled 1 ICFA interrupt request (ICIA) is enabled Rev. 3.00 Mar 17, 2006 page 621 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCSR—Timer Control/Status Register Bit H'FF91 FRT 7 6 5 4 3 2 1 0 ICFA ICFB ICFC ICFD OCFA OCFB OVF CCLRA Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R/W Counter Clear A 0 1 FRC clearing is disabled FRC is cleared at compare-match A Timer Overflow 0 1 [Clearing condition] When 0 is written in OVF after reading OVF = 1 [Setting condition] When the FRC value overflows from H'FFFF to H'0000 Output Compare Flag B 0 1 [Clearing condition] When 0 is written in OCFB after reading OCFB = 1 [Setting condition] When FRC = OCRB Output Compare Flag A 0 1 [Clearing condition] When 0 is written in OCFA after reading OCFA = 1 [Setting condition] When FRC = OCRA Input Capture Flag D 0 1 [Clearing condition] When 0 is written in ICFD after reading ICFD = 1 [Setting condition] When an input capture signal is generated Input Capture Flag C 0 1 [Clearing condition] When 0 is written in ICFC after reading ICFC = 1 [Setting condition] When an input capture signal is generated Input Capture Flag B 0 1 [Clearing condition] When 0 is written in ICFB after reading ICFB = 1 [Setting condition] When an input capture signal causes the FRC value to be transferred to ICRB Input Capture Flag A 0 1 [Clearing condition] When 0 is written in ICFA after reading ICFA = 1 [Setting condition] When an input capture signal causes the FRC value to be transferred to ICRA Note: * Only 0 can be written in bits 7 to 1, to clear the flags. Rev. 3.00 Mar 17, 2006 page 622 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers FRCH—Free-Running Counter H FRCL—Free-Running Counter L H'FF92 H'FF93 FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Up-counter OCRAH—Output Compare Register AH OCRAL—Output Compare Register AL OCRBH—Output Compare Register BH OCRBL—Output Compare Register BL H'FF94 H'FF95 H'FF94 H'FF95 FRT FRT FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Constantly compared with FRC value; OCF is set when OCR = FRC Rev. 3.00 Mar 17, 2006 page 623 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCR—Timer Control Register H'FF96 FRT 7 6 5 4 3 2 1 0 IEDGA IEDGB IEDGC IEDGD BUFEA BUFEB CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Clock Select 0 1 0 φ/2 internal clock source 1 φ/8 internal clock source 0 φ/32 internal clock source 1 External clock source (rising edge) Buffer Enable B 0 ICRD is not used as ICRB buffer register 1 ICRD is used as ICRB buffer register Buffer Enable A 0 ICRC is not used as ICRA buffer register 1 ICRC is used as ICRA buffer register Input Edge Select D 0 Capture on falling edge of input capture input D 1 Capture on rising edge of input capture input D Input Edge Select C 0 Capture on falling edge of input capture input C 1 Capture on rising edge of input capture input C Input Edge Select B 0 Capture on falling edge of input capture input B 1 Capture on rising edge of input capture input B Input Edge Select A 0 Capture on falling edge of input capture input A 1 Capture on rising edge of input capture input A Rev. 3.00 Mar 17, 2006 page 624 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TOCR—Timer Output Compare Control Register 7 Bit FRT 5 4 3 2 1 0 ICRS OCRS OEA OEB OLVLA OLVLB 6 ICRDMS OCRAMS H'FF97 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output Level B 0 0 output at comparematch B 1 1 output at comparematch B Output Level A 0 0 output at comparematch A 1 1 output at comparematch A Output Enable B 0 Output compare B output disabled 1 Output compare B output enabled Output Enable A 0 Output compare A output disabled 1 Output compare A output enabled Output Compare Register Select 0 OCRA register selected 1 OCRB register selected Input Capture Register Select 0 ICRA, ICRB, and ICRC registers selected 1 OCRAR, OCRAF, and OCRDM registers selected Output Compare A Mode Select 0 OCRA set to normal operating mode 1 OCRA set to operating mode using OCRAR and OCRAF Input Capture D Mode Select 0 ICRD set to normal operating mode 1 ICRD set to operating mode using OCRDM Rev. 3.00 Mar 17, 2006 page 625 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers OCRARH—Output Compare Register ARH OCRARL—Output Compare Register ARL OCRAFH—Output Compare Register AFH OCRAFL—Output Compare Register AFL H'FF98 H'FF99 H'FF9A H'FF9B FRT FRT FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Used for OCRA operation when OCRAMS = 1 in TOCR (For details see section 11.2.4, Output Compare Registers AR and AF (OCRAR, OCRAF).) ICRAH—Input Capture Register AH ICRAL—Input Capture Register AL ICRBH—Input Capture Register BH ICRBL—Input Capture Register BL H'FF98 H'FF99 H'FF9A H'FF9B FRT FRT FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Stores FRC value when input capture signal is input Rev. 3.00 Mar 17, 2006 page 626 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers OCRDMH—Output Compare Register DMH OCRDML—Output Compare Register DML H'FF9C H'FF9D FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R/W R/W R/W R/W R/W R/W R/W R/W Used for ICRD operation when ICRDMS = 1 in TOCR (For details see section 11.2.5, Output Compare Register DM (OCRDM).) ICRCH—Input Capture Register CH ICRCL—Input Capture Register CL ICRDH—Input Capture Register DH ICRDL—Input Capture Register DL H'FF9C H'FF9D H'FF9E H'FF9F FRT FRT FRT FRT Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R Stores FRC value when input capture signal is input (ICRC and ICRD can be used for buffer operation. For details see section 11.2.3, Input Capture Registers A to D (ICRA to ICRD).) Rev. 3.00 Mar 17, 2006 page 627 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers DACR—PWM (D/A) Control Register H'FFA0 PWMX 7 6 5 4 3 2 1 0 TEST PWME — — OEB OEA OS CKS Initial value 0 0 1 1 0 0 0 0 Read/Write R/W R/W — — R/W R/W R/W R/W Bit Clock Select 0 Operates at resolution (T) = system clock cycle time (tcyc) 1 Operates at resolution (T) = system clock cycle time (tcyc) × 2 Output Select 0 Direct PWM output 1 Inverted PWM output Output Enable A 0 PWM (D/A) channel A output (PWX0 output pin) disabled 1 PWM (D/A) channel A output (PWX0 output pin) enabled Output Enable B 0 PWM (D/A) channel B output (PWX1 output pin) disabled 1 PWM (D/A) channel B output (PWX1 output pin) enabled PWM Enable 0 DACNT operates as 14-bit up-counter 1 DACNT halts at H'0003 Test Mode 0 PWM (D/A) in user state, normal operation 1 PWM (D/A) in test state, correct conversion results unobtainable Rev. 3.00 Mar 17, 2006 page 628 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers DADRAH—PWM (D/A) Data Register AH DADRAL—PWM (D/A) Data Register AL DADRBH—PWM (D/A) Data Register BH DADRBL—PWM (D/A) Data Register BL H'FFA0 H'FFA1 H'FFA6 H'FFA7 DADRH PWMX PWMX PWMX PWMX DADRL Bit (CPU) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit (data) 13 12 11 10 9 8 7 6 5 4 3 2 1 0 — — DADRA Initial value DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CFS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 — 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W — DADRB Initial value DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 CFS REGS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Register Select (DADRB Only) 0 DADRA and DADRB can be accessed 1 DACR and DACNT can be accessed Carrier Frequency Select 0 Base cycle = resolution (T) × 64 DADR range = H'0401 to H'FFFD 1 Base cycle = resolution (T) × 256 DADR range = H'0103 to H'FFFF D/A Data 13 to 0 D/A conversion data. Rev. 3.00 Mar 17, 2006 page 629 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers DACNTH—PWM (D/A) Counter H DACNTL—PWM (D/A) Counter L H'FFA6 H'FFA7 DACNTH PWMX PWMX DACNTL Bit (CPU) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Bit (counter) 7 6 5 4 3 2 1 0 8 9 10 11 12 13 — — — REGS 1 1 Initial value Read/Write 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W — 0 R/W Register Select Up-counter Rev. 3.00 Mar 17, 2006 page 630 of 706 REJ09B0303-0300 0 DADRA and DADRB can be accessed 1 DACR and DACNT can be accessed Appendix B Internal I/O Registers TCSR0—Timer Control/Status Register 0 Bit 7 6 5 OVF WT/IT TME H'FFA8 4 3 RSTS RST/NMI WDT0 2 1 0 CKS2 CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/W R/W R/W R/W R/W R/W R/W Clock Select 2 to 0 CKS1 CKS0 0 0 0 φ/2 25.6 µs 1 φ/64 819.2 µs 0 φ/128 1.6 ms 1 φ/512 6.6 ms 0 φ/2048 26.2 ms 1 φ/8192 104.9 ms 0 φ/32768 419.4 ms 1 φ/131072 1.68 s 1 1 0 1 Clock Overflow Period (when φ = 20 MHz) CKS2 Reset or NMI 0 NMI interrupt requested 1 Internal reset requested Reserved Timer Enable 0 TCNT is initialized to H'00 and halted 1 TCNT counts Timer Mode Select 0 Interval timer mode: Sends the CPU an interval timer interrupt request (WOVI) when TCNT overflows 1 Watchdog timer mode: Generates a reset or NMI interrupt when TCNT overflows Overflow Flag 0 [Clearing conditions] • When 0 is written in the TME bit • When 0 is written in OVF after reading TCSR when OVF = 1 1 [Setting condition] When TCNT overflows from H'FF to H'00 (When internal reset request generation is selected in watchdog timer mode, OVF is cleared automatically by the internal reset) Notes: The method of writing to TCSR is more complicated that for most other registers, to prevent accidental overwriting. For details see section 14.2.4, Notes on Register Access. * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 631 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCNT0—Timer Counter 0 H'FFA8 (W), H'FFA9 (R) WDT0 Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Up-counter P1PCR—Port 1 MOS Pull-Up Control Register Bit 7 6 5 4 H'FFAC 3 Port 1 2 1 0 P17PCR P16PCR P15PCR P14PCR P13PCR P12PCR P11PCR P10PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Control port 1 MOS input pull-ups P2PCR—Port 2 MOS Pull-Up Control Register Bit 7 6 5 4 H'FFAD 3 Port 2 2 1 0 P27PCR P26PCR P25PCR P24PCR P23PCR P22PCR P21PCR P20PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Control port 2 MOS input pull-ups Rev. 3.00 Mar 17, 2006 page 632 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers P3PCR—Port 3 MOS Pull-Up Control Register Bit 7 6 5 4 H'FFAE 3 Port 3 2 1 0 P37PCR P36PCR P35PCR P34PCR P33PCR P32PCR P31PCR P30PCR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Control port 3 MOS input pull-ups P1DDR—Port 1 Data Direction Register Bit 7 6 5 H'FFB0 4 3 Port 1 2 1 0 P17DDR P16DDR P15DDR P14DDR P13DDR P12DDR P11DDR P10DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port 1 pins P2DDR—Port 2 Data Direction Register Bit 7 6 5 H'FFB1 4 3 Port 2 2 1 0 P27DDR P26DDR P25DDR P24DDR P23DDR P22DDR P21DDR P20DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port 2 pins Rev. 3.00 Mar 17, 2006 page 633 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers P1DR—Port 1 Data Register Bit H'FFB2 Port 1 7 6 5 4 3 2 1 0 P17DR P16DR P15DR P14DR P13DR P12DR P11DR P10DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port 1 pins P2DR—Port 2 Data Register Bit H'FFB3 Port 2 7 6 5 4 3 2 1 0 P27DR P26DR P25DR P24DR P23DR P22DR P21DR P20DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port 2 pins P3DDR—Port 3 Data Direction Register Bit 7 6 5 H'FFB4 4 3 Port 3 2 1 0 P37DDR P36DDR P35DDR P34DDR P33DDR P32DDR P31DDR P30DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port 3 pins Rev. 3.00 Mar 17, 2006 page 634 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers P4DDR—Port 4 Data Direction Register Bit 7 6 5 H'FFB5 4 3 Port 4 2 1 0 P47DDR P46DDR P45DDR P44DDR P43DDR P42DDR P41DDR P40DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port 4 pins P3DR—Port 3 Data Register Bit H'FFB6 Port 3 7 6 5 4 3 2 1 0 P37DR P36DR P35DR P34DR P33DR P32DR P31DR P30DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port 3 pins P4DR—Port 4 Data Register Bit H'FFB7 Port 4 7 6 5 4 3 2 1 0 P47DR P46DR P45DR P44DR P43DR P42DR P41DR P40DR Initial value 0 —* 0 0 0 0 0 0 Read/Write R/W R R/W R/W R/W R/W R/W R/W Output data for port 4 pins Note: * Determined by the state of pin P46. Rev. 3.00 Mar 17, 2006 page 635 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers P5DDR—Port 5 Data Direction Register Bit H'FFB8 7 6 5 4 3 Port 5 2 1 0 P52DDR P51DDR P50DDR — — — — — Initial value 1 1 1 1 1 0 0 0 Read/Write — — — — — W W W Specify input or output for port 5 pins P6DDR—Port 6 Data Direction Register Bit 7 6 5 H'FFB9 4 Port 6 3 2 1 0 P67DDR P66DDR P65DDR P64DDR P63DDR P62DDR P61DDR P60DDR Initial value 0 0 0 0 0 0 0 0 Read/Write W W W W W W W W Specify input or output for port 6 pins P5DR—Port 5 Data Register Bit H'FFBA Port 5 7 6 5 4 3 2 1 0 — — — — — P52DR P51DR P50DR Initial value 1 1 1 1 1 0 0 0 Read/Write — — — — — R/W R/W R/W Output data for port 5 pins Rev. 3.00 Mar 17, 2006 page 636 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers P6DR—Port 6 Data Register Bit H'FFBB Port 6 7 6 5 4 3 2 1 0 P67DR P66DR P65DR P64DR P63DR P62DR P61DR P60DR Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Output data for port 6 pins P7PIN—Port 7 Input Data Register Bit H'FFBE Port 7 7 6 5 4 3 2 1 0 P77PIN P76PIN P75PIN P74PIN P73PIN P72PIN P71PIN P70PIN Initial value —* —* —* —* —* —* —* —* Read/Write R R R R R R R R Port 7 pin states Note: * Determined by the state of pins P77 to P70. IER—IRQ Enable Register Bit H'FFC2 Interrupt Controller 7 6 5 4 3 2 1 0 — — — — — IRQ2E IRQ1E IRQ0E Initial value 1 1 1 1 1 0 0 0 Read/Write R R R R R R/W R/W R/W IRQ2 to IRQ0 Enable 0 IRQn interrupt disabled 1 IRQn interrupt enabled (n = 2 to 0) Rev. 3.00 Mar 17, 2006 page 637 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers STCR—Serial Timer Control Register Bit : Initial value : R/W : H'FFC3 System 7 6 5 4 3 2 1 0 — IICX1 IICX0 IICE — USBE ICKS1 ICKS0 0 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W R/W Internal Clock Source select*1 USB Enable 0 CPU access to USB data registers and control registers is disabled 1 CPU access to USB data registers and control registers is enabled Reserved I2C Master Enable 0 CPU access to I2C bus interface data registers and control registers is disabled 1 CPU access to I2C bus interface data registers and control registers is enabled I2C Transfer Rate Select 1 and 0*2 Reserved Notes: 1. Used for 8-bit timer input clock selection. For details see section 12.2.4, Timer Control Register (TCR). 2. Used for I2C bus interface transfer clock selection. For details see section 16.2.4, I2C Bus Mode Register (ICMR). Rev. 3.00 Mar 17, 2006 page 638 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SYSCR—System Control Register Bit H'FFC4 System 7 6 5 4 3 2 1 0 CS2E IOSE INTM1 INTM0 XRST NMIEG HIE RAME Initial value 0 0 0 0 1 0 0 1 Read/Write R/W R/W R R R R/W R/W R/W RAM Enable 0 On-chip RAM is disabled 1 On-chip RAM is enabled Host Interface Enable 0 In areas H'FFF0 to H'FFF7 and H'FFFC to H'FFFF, CPU access to 8-bit timer (channel X and Y) data registers and control registers, and timer connection control registers, is permitted 1 In areas H'FFF0 to H'FFF7 and H'FFFC to H'FFFF, CPU access to 8-bit timer (channel X and Y) data registers and control registers, and timer connection control registers, is not permitted NMI Edge Select 0 Interrupt request generated by NMI falling edge 1 Interrupt request generated by NMI rising edge External Reset 0 Reset generated by watchdog timer overflow 1 Reset generated by external reset Interrupt Control Mode 1 and 0 INTM1 INTM0 0 1 Interrupt Control Mode Description 0 0 Interrupts are controlled by I bit 1 1 Cannot be used in these groups 0 2 Cannot be used in these groups 1 3 Cannot be used in these groups IOS Enable Do not set this bit to 1. Chip Select 2 Enable Do not set this bit to 1. Rev. 3.00 Mar 17, 2006 page 639 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers MDCR—Mode Control Register H'FFC5 System 7 6 5 4 3 2 1 0 EXPE — — — — — MDS1 MDS0 Initial value 0* 0 0 0 0 0 1* 1* Read/Write R — — — — — R R Bit Mode Select 1 and 0 Mode pin states. Expanded Mode Enable Note: * Determined by the MD1 and MD0 pins (H8/3577 Group) or the TEST pin (H8/3567 Group). BCR—Bus Control Register H'FFC6 7 6 ICIS1 ICIS0 Initial value 1 1 0 1 Read/Write R/W R/W R R/W Bit 5 4 3 Bus Controller 2 1 0 — IOS1 IOS0 0 1 1 1 R R/W R/W R/W BRSTRM BRSTS1 BRSTS0 Do not write any values other than the initial values. WSCR—Wait State Control Register Bit H'FFC7 Bus Controller 7 6 5 4 3 2 1 0 RAMS RAM0 ABW AST WMS1 WMS0 WC1 WC0 Initial value 0 0 1 1 0 0 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Do not write any values other than the initial values. Rev. 3.00 Mar 17, 2006 page 640 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCR0—Timer Control Register 0 TCR1—Timer Control Register 1 H'FFC8 H'FFC9 TMR0 TMR1 7 6 5 4 3 2 1 0 CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 Bit Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Counter Clear 1 and 0 0 0 Clearing is disabled 1 Cleared on comparematch A 0 Cleared on comparematch B 1 Cleared on rising edge of external reset input Clock Select 2 to 0 Channel 1 Bit 2 Bit 1 Bit 0 Description CKS2 CKS1 CKS0 0 0 0 0 Clock input disabled 1*1 φ/8 internal clock source, counted on falling edge φ/2 internal clock source, counted on falling edge 1 0*1 φ/64 internal clock source, counted on falling edge φ/32 internal clock source, counted on falling edge 1*1 φ/1024 internal clock source, counted on falling edge Timer Overflow Interrupt Enable 0 OVF interrupt request (OVI) is disabled 1 OVF interrupt request (OVI) is enabled φ/256 internal clock source, counted on falling edge 1 1 0 0 Counted on TCNT1 overflow signal*2 0 0 0 Clock input disabled 1*1 φ/8 internal clock source, counted on falling edge Compare-Match Interrupt Enable A 0 CMFA interrupt request (CMIA) is disabled 1 CMFA interrupt request (CMIA) is enabled φ/2 internal clock source, counted on falling edge 1 0*1 φ/64 internal clock source, counted on falling edge φ/128 internal clock source, counted on falling edge 1*1 φ/1024 internal clock source, counted on falling edge Compare-Match Interrupt Enable B 0 CMFB interrupt request (CMIB) is disabled 1 CMFB interrupt request (CMIB) is enabled φ/2048 internal clock source, counted on falling edge X 1 0 0 Counted on TCNT0 compare-match A*2 0 0 0 Clock input disabled 1 Counted on φ internal clock source 0 φ/2 internal clock source, counted on falling edge 1 φ/4 internal clock source, counted on falling edge 1 Y 1 0 0 Clock input disabled 0 0 0 Clock input disabled 1 φ/4 internal clock source, counted on falling edge 0 φ/256 internal clock source, counted on falling edge 1 φ/2048 internal clock source, counted on falling edge 1 Common 1 0 0 Clock input disabled 1 0 1 External clock source, counted on rising edge 1 0 External clock source, counted on falling edge 1 External clock source, counted on both rising and falling edges Notes: 1. Selected by ICKS1 and ICKS0 in STCR. For details see section 12.2.4, Timer Control Register (TCR). 2. If the count input of channel 0 is the TCNT1 overflow signal and that of channel 1 is the TCNT0 compare-match signal, no incrementing clock will be generated. Do not use this setting. Rev. 3.00 Mar 17, 2006 page 641 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCSR0—Timer Control/Status Register 0 H'FFCA TMR0 TCSR0 Bit 7 6 5 4 3 2 1 0 CMFB CMFA OVF ADTE OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/W R/W R/W R/W R/W Output Select 1 and 0 0 0 1 No change when compare-match A occurs 1 0 output when compare-match A occurs 0 1 output when compare-match A occurs 1 Output inverted when compare-match A occurs (toggle output) Output Select 3 and 2 0 1 0 No change when compare-match B occurs 1 0 output when compare-match B occurs 0 1 output when compare-match B occurs 1 Output inverted when compare-match B occurs (toggle output) A/D Trigger Enable 0 A/D converter start requests by compare-match A are disabled 1 A/D converter start requests by compare-match A are enabled Timer Overflow Flag 0 [Clearing condition] When 0 is written in OVF after reading OVF = 1 1 [Setting condition] When TCNT overflows from H'FF to H'00 Compare-Match Flag A 0 [Clearing condition] When 0 is written in CMFA after reading CMFA = 1 1 [Setting condition] When TCNT = TCORA Compare-Match Flag B 0 [Clearing condition] When 0 is written in CMFB after reading CMFB = 1 1 [Setting condition] When TCNT = TCORB Note: * Only 0 can be written in bits 7 to 5, to clear the flags. Rev. 3.00 Mar 17, 2006 page 642 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCSR1—Timer Control/Status Register 1 H'FFCB TMR1 TCSR1 7 6 5 4 3 2 1 0 CMFB CMFA OVF — OS3 OS2 OS1 OS0 Initial value 0 0 0 1 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* — R/W R/W R/W R/W Bit Output Select 1 and 0 0 1 0 No change when compare-match A occurs 1 0 output when compare-match A occurs 0 1 output when compare-match A occurs 1 Output inverted when compare-match A occurs (toggle output) Output Select 3 and 2 0 1 0 No change when compare-match B occurs 1 0 output when compare-match B occurs 0 1 output when compare-match B occurs 1 Output inverted when compare-match B occurs (toggle output) Timer Overflow Flag 0 [Clearing condition] When 0 is written in OVF after reading OVF = 1 1 [Setting condition] When TCNT overflows from H'FF to H'00 Compare-Match Flag A 0 [Clearing condition] When 0 is written in CMFA after reading CMFA = 1 1 [Setting condition] When TCNT = TCORA Compare-Match Flag B 0 [Clearing condition] When 0 is written in CMFB after reading CMFB = 1 1 [Setting condition] When TCNT = TCORB Note: * Only 0 can be written in bits 7 to 5, to clear the flags. Rev. 3.00 Mar 17, 2006 page 643 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCORA0—Time Constant Register A0 TCORA1—Time Constant Register A1 TCORB0—Time Constant Register B0 TCORB1—Time Constant Register B1 H'FFCC H'FFCD H'FFCE H'FFCF TCORA0 TCORB0 TMR0 TMR1 TMR0 TMR1 TCORA1 TCORB1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Compare-match flag (CMF) is set when TCOR and TCNT values match TCNT0—Timer Counter 0 TCNT1—Timer Counter 1 H'FFD0 H'FFD1 TCNT0 TMR0 TMR1 TCNT1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Up-counter Rev. 3.00 Mar 17, 2006 page 644 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PWOERB—PWM Output Enable Register B PWOERA—PWM Output Enable Register A Bit PWOERB H'FFD2 H'FFD3 PWM PWM 7 6 5 4 3 2 1 0 OE15 OE14 OE13 OE12 OE11 OE10 OE9 OE8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 PWOERA OE7 OE6 OE5 OE4 OE3 OE2 OE1 OE0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Switching between PWM output and port output DDR OE 0 0 Port input 1 Port input 0 Port output or PWM 256/256 output 1 PWM output (0 to 255/256 output) 1 Description Rev. 3.00 Mar 17, 2006 page 645 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PWDPRB—PWM Data Polarity Register B PWDPRA—PWM Data Polarity Register A Bit PWDPRB H'FFD4 H'FFD5 PWM PWM 7 6 5 4 3 2 1 0 OS15 OS14 OS13 OS12 OS11 OS10 OS9 OS8 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 OS7 OS6 OS5 OS4 OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit PWDPRA PWM output polarity control 0 PWM direct output (PWDR value corresponds to high width of output) 1 PWM inverted output (PWDR value corresponds to low width of output) Rev. 3.00 Mar 17, 2006 page 646 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PWSL—PWM Register Select 7 Bit H'FFD6 6 PWCKE PWCKS PWM 5 4 3 2 1 0 — — RS3 RS2 RS1 RS0 Initial value 0 0 1 0 0 0 0 0 Read/Write R/W R/W — — R/W R/W R/W R/W Register Select 0 0 0 0 PWDR0 selected 1 PWDR1 selected 1 0 PWDR2 selected 1 PWDR3 selected 1 0 0 PWDR4 selected 1 PWDR5 selected 1 0 PWDR6 selected 1 PWDR7 selected 1 0 0 0 PWDR8 selected 1 PWDR9 selected 1 0 PWDR10 selected 1 PWDR11 selected 1 0 0 PWDR12 selected 1 PWDR13 selected 1 0 PWDR14 selected 1 PWDR15 selected PWM Clock Enable, PWM Clock Select PWSL Bit 7 PCSR Bit 6 Bit 2 Bit 1 Description PWCKE PWCKS PWCKB PWCKA 0 — — — Clock input disabled 1 0 — — φ (system clock) selected 1 0 0 φ/2 selected 1 φ/4 selected 0 φ/8 selected 1 φ/16 selected 1 Rev. 3.00 Mar 17, 2006 page 647 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers PWDR0 to PWDR15—PWM Data Registers H'FFD7 PWM Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Specifies duty cycle of basic output pulse and number of additional pulses Rev. 3.00 Mar 17, 2006 page 648 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICCR0—I C Bus Control Register 0 Bit H'FFD8 IIC0 7 6 5 4 3 2 1 0 ICE IEIC MST TRS ACKE BBSY IRIC SCP Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/(W)* W Start Condition/Stop Condition Prohibit 0 Writing issues a start or stop condition, in combination with the BBSY flag 1 Reading always returns a value of 1; writing is invalid I2C Bus Interface Interrupt Request Flag 0 Waiting for transfer, or transfer in progress 1 Interrupt requested Note: For the clearing and setting conditions, see section 16.2.5, I2C Bus Control Register (ICCR). Bus Busy 0 Bus is free [Clearing condition] When a stop condition is detected 1 Bus is busy [Setting condition] When a start condition is detected Acknowledge Bit Judgement Select 0 Acknowledge bit is ignored and continuous transfer is performed 1 If acknowledge bit is 1, continuous transfer is interrupted Master/Slave Select (MST), Transmit/Receive Select (TRS) 0 1 0 Slave receive mode 1 Slave transmit mode 0 Master receive mode 1 Master transmit mode Note: For details see section 16.2.5, I2C Bus Control Register (ICCR). I2C Bus Interface Interrupt Enable I2C 0 Interrupt requests disabled 1 Interrupt requests enabled Bus Interface Enable 0 I2C bus interface module disabled, with SCL and SDA signal pins set to port function SAR and SARX can be accessed 1 I2C bus interface module enabled for transfer operations (pins SCL and SDA are driving the bus) ICMR and ICDR can be accessed Note: * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 649 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SMR0—Serial Mode Register 0 Bit H'FFD8 SCI0 7 6 5 4 3 2 1 0 C/A CHR PE O/E STOP MP CKS1 CKS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Clock Select 1 and 0 0 1 0 φ clock 1 φ/4 clock 0 φ/16 clock 1 φ/64 clock Multiprocessor Mode 0 Multiprocessor function disabled 1 Multiprocessor format selected Stop Bit Length 0 1 stop bit*1 1 2 stop bits*2 Notes: 1. In transmission, a single 1 bit (stop bit) is added to the end of a transmit character before it is sent. 2. In transmission, two 1 bits (stop bits) are added to the end of a transmit character before it is sent. Parity Mode 0 Even parity*1 1 Odd parity*2 Notes: 1. When even parity is set, parity bit addition is performed in transmission so that the total number of 1 bits in the transmit character plus the parity bit is even. In reception, a check is performed to see if the total number of 1 bits in the receive character plus the parity bit is even. 2. When odd parity is set, parity bit addition is performed in transmission so that the total number of 1 bits in the transmit character plus the parity bit is odd. In reception, a check is performed to see if the total number of 1 bits in the receive character plus the parity bit is odd. Parity Enable 0 Parity bit addition and checking disabled 1 Parity bit addition and checking enabled* Note: * When the PE bit is set to 1, the parity (even or odd) specified by the O/E bit is added to transmit data before transmission. In reception, the parity bit is checked for the parity (even or odd) specified by the O/E bit. Character Length 0 8-bit data 1 7-bit data* Note: * When 7-bit data is selected, the MSB (bit 7) of TDR is not transmitted, and LSB-first/MSB-first selection is not available. Communication Mode 0 Asynchronous mode 1 Synchronous mode Rev. 3.00 Mar 17, 2006 page 650 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers BRR0—Bit Rate Register 0 H'FFD9 SCI0 Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Sets the serial transmit/receive bit rate Rev. 3.00 Mar 17, 2006 page 651 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICSR0—I C Bus Status Register 0 Bit H'FFD9 IIC0 7 6 5 4 3 2 1 0 ESTP STOP IRTR AASX AL AAS ADZ ACKB 0 0 0 0 0 0 Initial value 0 Read/Write R/(W)*1 R/(W)*1 R/(W)*1 R/(W)*1 R/(W)*1 R/(W)*1 R/(W)*1 0 R/W Acknowledge Bit 0 Receive mode: 0 is output at acknowledge output timing Transmit mode: indicates that the receiving device has acknowledged the data (0 value) 1 Receive mode: 1 is output at acknowledge output timing Transmit mode: indicates that the receiving device has not acknowledged the data (1 value) General Call Address Recognition Flag*2 0 General call address not recognized 1 General call address recognized Slave Address Recognition Flag*2 0 Slave address or general call address not recognized 1 Slave address or general call address recognized Arbitration Lost Flag*2 0 Bus arbitration won 1 Bus arbitration lost Second Slave Address Recognition Flag*2 0 Second slave address not recognized 1 Second slave address recognized I2C Bus Interface Continuous Transmission/Reception Interrupt Request Flag*2 0 Waiting for transfer, or transfer in progress 1 Continuous transfer state Normal Stop Condition Detection Flag*2 0 No normal stop condition 1 In I2C bus format slave mode: Normal stop condition detected In other modes: No meaning Error Stop Condition Detection Flag*2 0 No error stop condition 1 In I2C bus format slave mode: Error stop condition detected In other modes: No meaning Notes: 1. Only 0 can be written, to clear the flag. 2. For the clearing and setting conditions, see section 16.2.6, I2C Bus Status Register (ICSR). Rev. 3.00 Mar 17, 2006 page 652 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SCR0—Serial Control Register 0 Bit H'FFDA SCI0 7 6 5 4 3 2 1 0 TIE RIE TE RE MPIE TEIE CKE1 CKE0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Clock Enable 1 and 0 0 1 0 Asynchronous mode Synchronous mode 1 Asynchronous mode Synchronous mode 0 Asynchronous mode Synchronous mode 1 Asynchronous mode Synchronous mode Internal clock/SCK pin functions as I/O port Internal clock/SCK pin functions as serial clock output Internal clock/SCK pin functions as clock output Internal clock/SCK pin functions as serial clock output External clock/SCK pin functions as clock input External clock/SCK pin functions as serial clock input External clock/SCK pin functions as clock input External clock/SCK pin functions as serial clock input Transmit End Interrupt Enable 0 Transmit end interrupt (TEI) request disabled 1 Transmit end interrupt (TEI) request enabled Multiprocessor Interrupt Enable 0 Multiprocessor interrupts disabled (normal reception performed) [Clearing conditions] • When the MPIE bit is cleared to 0 • When data with MPB = 1 is received 1 Multiprocessor interrupts enabled Receive interrupt (RXI) requests, receive error interrupt (ERI) requests, and setting of the RDRF, FER, and ORER flags in SSR are disabled until data with the multiprocessor bit set to 1 is received Receive Enable 0 Reception disabled 1 Reception enabled Transmit Enable 0 Transmission disabled 1 Transmission enabled Receive Interrupt Enable 0 Receive data full interrupt (RXI) request and receive error interrupt (ERI) request disabled 1 Receive data full interrupt (RXI) request and receive error interrupt (ERI) request enabled Transmit Interrupt Enable 0 Transmit data empty interrupt (TXI) request disabled 1 Transmit data empty interrupt (TXI) request enabled Rev. 3.00 Mar 17, 2006 page 653 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TDR0—Transmit Data Register 0 H'FFDB SCI0 Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Serial transmit data Rev. 3.00 Mar 17, 2006 page 654 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SSR0—Serial Status Register 0 H'FFDC SCI0 7 6 5 4 3 2 1 0 TDRE RDRF ORER FER PER TEND MPB MPBT Initial value 1 0 0 0 0 1 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/(W)* R R R/W Bit Multiprocessor Bit Transfer 0 Data with a 0 multiprocessor bit is transmitted 1 Data with a 1 multiprocessor bit is transmitted Multiprocessor Bit 0 [Clearing condition] When data with a 0 multiprocessor bit is received 1 [Setting condition] When data with a 1 multiprocessor bit is received Transmit End 0 [Clearing condition] When 0 is written in TDRE after reading TDRE = 1 1 [Setting conditions] • When the TE bit in SCR is 0 • When TDRE = 1 at transmission of the last bit of a 1-byte serial transmit character Parity Error 0 Clearing condition] When 0 is written in PER after reading PER = 1 1 [Setting condition] When, in reception, the number of 1 bits in the receive data plus the parity bit does not match the parity setting (even or odd) specified by the O/E bit in SMR Framing Error 0 [Clearing condition] When 0 is written in FER after reading FER = 1 1 [Setting condition] When the SCI checks the stop bit at the end of the receive data when reception ends, and the stop bit is 0 Overrun Error 0 [Clearing condition] When 0 is written in ORER after reading ORER = 1 1 [Setting condition] When the next serial reception is completed while RDRF = 1 Receive Data Register Full 0 [Clearing condition] When 0 is written in RDRF after reading RDRF = 1 1 [Setting condition] When serial reception ends normally and receive data is transferred from RSR to RDR Transmit Data Register Empty 0 [Clearing condition] When 0 is written in TDRE after reading TDRE = 1 1 [Setting conditions] • When the TE bit in SCR is 0 • When data is transferred from TDR to TSR and data can be written in TDR Note: * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 655 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers RDR0—Receive Data Register 0 H'FFDD SCI0 Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R Serial receive data SCMR0—Serial Interface Mode Register 0 Bit H'FFDE SCI0 7 6 5 4 3 2 1 0 — — — — SDIR SINV — SMIF Initial value 1 1 1 1 0 0 1 0 Read/Write — — — — R/W R/W — R/W Serial Communication Interface Mode Select 0 Normal SCI mode 1 Setting prohibited Data Invert 0 TDR contents are transmitted without modification Receive data is stored in RDR without modification 1 TDR contents are inverted before being transmitted Receive data is stored in RDR in inverted form Data Transfer Direction 0 TDR contents are transmitted LSB-first Receive data is stored in RDR LSB-first 1 TDR contents are transmitted MSB-first Receive data is stored in RDR MSB-first Rev. 3.00 Mar 17, 2006 page 656 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICDR0—I C Bus Data Register 0 Bit H'FFDE IIC0 7 6 5 4 3 2 1 0 ICDR7 ICDR6 ICDR5 ICDR4 ICDR3 ICDR2 ICDR1 ICDR0 Initial value — — — — — — — — Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 • ICDRR Bit ICDRR7 ICDRR6 ICDRR5 ICDRR4 ICDRR3 ICDRR2 ICDRR1 ICDRR0 Initial value — — — — — — — — Read/Write R R R R R R R R 7 6 5 4 3 2 1 0 • ICDRS Bit ICDRS7 ICDRS6 ICDRS5 ICDRS4 ICDRS3 ICDRS2 ICDRS1 ICDRS0 Initial value — — — — — — — — Read/Write — — — — — — — — 7 6 5 4 3 2 1 0 • ICDRT Bit ICDRT7 ICDRT6 ICDRT5 ICDRT4 ICDRT3 ICDRT2 ICDRT1 ICDRT0 Initial value — — — — — — — — Read/Write W W W W W W W W — — TDRE RDRF • TDRE, RDRF (internal flags) Bit Initial value 0 0 Read/Write — — Note: For details see section 16.2.1, I2C Bus Data Register (ICDR). Rev. 3.00 Mar 17, 2006 page 657 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SARX0—Second Slave Address Register 0 H'FFDE IIC0 7 6 5 4 3 2 1 0 SVAX6 SVAX5 SVAX4 SVAX3 SVAX2 SVAX1 SVAX0 FSX Initial value 0 0 0 0 0 0 0 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Second Slave Address Format Select DDCSWR Bit 6 SAR Bit 0 SARX Bit 0 SW FS FSX 0 0 0 I2C bus format • SAR and SARX slave addresses recognized 1 I2C bus format • SAR slave address recognized • SARX slave address ignored 0 I2C bus format • SAR slave address ignored • SARX slave address recognized 1 Synchronous serial format • SAR and SARX slave addresses ignored 0 Formatless mode (start/stop conditions not detected) • Acknowledge bit present 1 1 0 1 1 0 1 Operating Mode Formatless mode* (start/stop conditions not detected) • No acknowledge bit Note: * Do not select this mode when automatic switching to the I2C bus format is performed by means of a DDCSWR setting. Rev. 3.00 Mar 17, 2006 page 658 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SAR0—Slave Address Register 0 H'FFDF IIC0 7 6 5 4 3 2 1 0 SVA6 SVA5 SVA4 SVA3 SVA2 SVA1 SVA0 FS Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Slave Address Format Select DDCSWR Bit 6 SAR Bit 0 SARX Bit 0 SW FS FSX 0 0 0 I2C bus format • SAR and SARX slave addresses recognized 1 I2C bus format • SAR slave address recognized • SARX slave address ignored 0 I2C bus format • SAR slave address ignored • SARX slave address recognized 1 Synchronous serial format • SAR and SARX slave addresses ignored 0 Formatless mode (start/stop conditions not detected) • Acknowledge bit present 1 1 0 1 1 0 1 Operating Mode Formatless mode* (start/stop conditions not detected) • No acknowledge bit Note: * Do not select this mode when automatic switching to the I2C bus format is performed by means of a DDCSWR setting. Rev. 3.00 Mar 17, 2006 page 659 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers 2 ICMR0—I C Bus Mode Register 0 H'FFDF IIC0 7 6 5 4 3 2 1 0 MLS WAIT CKS2 CKS1 CKS0 BC2 BC1 BC0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Bit Bit Counter BC2 BC1 BC0 0 0 0 1 0 1 0 1 0 1 1 1 0 1 Synchronous Serial Format 8 1 2 3 4 5 6 7 Transfer Clock Select IICX 0 CKS2 0 CKS1 0 1 1 0 1 1 0 0 1 1 0 1 CKS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Clock φ/28 φ/40 φ/48 φ/64 φ/80 φ/100 φ/112 φ/128 φ/56 φ/80 φ/96 φ/128 φ/160 φ/200 φ/224 φ/256 Wait Insertion Bit 0 Data and acknowledge transferred consecutively 1 Wait inserted between data and acknowledge MSB-First/LSB-First Select* 0 MSB-first 1 LSB-first Note: * Do not set this bit to 1 when using the I2C bus format. Rev. 3.00 Mar 17, 2006 page 660 of 706 REJ09B0303-0300 I2C Bus Format 9 2 3 4 5 6 7 8 Appendix B Internal I/O Registers ADDRAH—A/D Data Register AH ADDRAL—A/D Data Register AL ADDRBH—A/D Data Register BH ADDRBL—A/D Data Register BL ADDRCH—A/D Data Register CH ADDRCL—A/D Data Register CL ADDRDH—A/D Data Register DH ADDRDL—A/D Data Register DL H'FFE0 H'FFE1 H'FFE2 H'FFE3 H'FFE4 H'FFE5 H'FFE6 H'FFE7 ADDRH Bit 14 12 A/D A/D A/D A/D A/D A/D A/D A/D ADDRL 10 8 6 5 4 3 2 1 0 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 — 15 13 11 9 7 — — — — — Initial value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R R R R R R R R R A/D data Correspondence between analog input channels and ADDR registers Analog Input Channel A/D Data Register Group 0 Group 1 AN0 AN4 ADDRA AN1 AN5 ADDRB AN2 AN6 ADDRC AN3 AN7 ADDRD Rev. 3.00 Mar 17, 2006 page 661 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers ADCSR—A/D Control/Status Register H'FFE8 A/D Converter 7 6 5 4 3 2 1 0 ADF ADIE ADST SCAN CKS CH2 CH1 CH0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/W R/W R/W R/W R/W R/W R/W Bit Channel Select Group Selection Channel Selection Description CH2 CH1 CH0 H8/3577 Group / H8/3567 Group 0 0 0 AN0 AN0 1 AN1 AN0, AN1 0 AN2 AN0, AN1, AN2 1 AN3 AN0, AN1, AN2, AN3 H8/3577 Group only 1 0 AN4 AN4 1 AN5 AN4, AN5 0 AN6 AN4, AN5, AN6 1 AN7 AN4, AN5, AN6, AN7 1 0 1 Single Mode Scan Mode Clock Select 0 Conversion time = 266 states (max.) 1 Conversion time = 134 states (max.) Scan Mode 0 Single mode 1 Scan mode A/D Start 0 A/D conversion stopped 1 • Single mode: A/D conversion is started. Cleared to 0 automatically when conversion on the specified channel ends • Scan mode: A/D conversion is started. Conversion continues consecutively on the selected channels until ADST is cleared to 0 by software, a reset, or a transition to standby mode or module stop mode A/D Interrupt Enable 0 A/D conversion end interrupt (ADI) request disabled 1 A/D conversion end interrupt (ADI) request enabled A/D end flag 0 [Clearing condition] When 0 is written in ADF after reading ADF = 1 1 [Setting conditions] • Single mode: When A/D conversion ends • Scan mode: When A/D conversion ends on all specified channels Note: * Only 0 can be written, to clear the flag. Rev. 3.00 Mar 17, 2006 page 662 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers ADCR—A/D Control Register H'FFE9 A/D 7 6 5 4 3 2 1 0 TRGS1 TRGS0 — — — — — — Initial value 0 0 1 1 1 1 1 1 Read/Write R/W R/W — — — — — — Bit Timer Trigger Select 0 1 0 Start of A/D conversion by external trigger is disabled 1 Start of A/D conversion by external trigger is disabled 0 Start of A/D conversion by external trigger (8-bit timer) is enabled 1 Start of A/D conversion by external trigger pin is enabled Rev. 3.00 Mar 17, 2006 page 663 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCRX—Timer Control Register X TCRY—Timer Control Register Y H'FFF0 H'FFF0 TMRX TMRY 7 6 5 4 3 2 1 0 CMIEB CMIEA OVIE CCLR1 CCLR0 CKS2 CKS1 CKS0 Bit Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Counter Clear 1 and 0 0 0 Clearing is disabled 1 Cleared on comparematch A 0 Cleared on comparematch B 1 Cleared on rising edge of external reset input Clock Select 2 to 0 Channel 1 Bit 2 Bit 1 Bit 0 Description CKS2 CKS1 CKS0 0 0 0 0 Clock input disabled 1*1 φ/8 internal clock source, counted on falling edge φ/2 internal clock source, counted on falling edge 1 0*1 φ/64 internal clock source, counted on falling edge φ/32 internal clock source, counted on falling edge 1*1 φ/1024 internal clock source, counted on falling edge Timer Overflow Interrupt Enable 0 OVF interrupt request (OVI) is disabled 1 OVF interrupt request (OVI) is enabled φ/256 internal clock source, counted on falling edge 1 1 0 0 Counted on TCNT1 overflow signal*2 0 0 0 Clock input disabled 1*1 φ/8 internal clock source, counted on falling edge Compare-Match Interrupt Enable A 0 CMFA interrupt request (CMIA) is disabled 1 CMFA interrupt request (CMIA) is enabled φ/2 internal clock source, counted on falling edge 1 0*1 φ/64 internal clock source, counted on falling edge φ/128 internal clock source, counted on falling edge 1*1 φ/1024 internal clock source, counted on falling edge Compare-Match Interrupt Enable B 0 CMFB interrupt request (CMIB) is disabled 1 CMFB interrupt request (CMIB) is enabled φ/2048 internal clock source, counted on falling edge X 1 0 0 Counted on TCNT0 compare-match A*2 0 0 0 Clock input disabled 1 Counted on φ internal clock source 0 φ/2 internal clock source, counted on falling edge 1 φ/4 internal clock source, counted on falling edge 1 Y 1 0 0 Clock input disabled 0 0 0 Clock input disabled 1 φ/4 internal clock source, counted on falling edge 0 φ/256 internal clock source, counted on falling edge 1 φ/2048 internal clock source, counted on falling edge 1 Common 1 0 0 Clock input disabled 1 0 1 External clock source, counted on rising edge 1 0 External clock source, counted on falling edge 1 External clock source, counted on both rising and falling edges Notes: 1. Selected by ICKS1 and ICKS0 in STCR. For details see section 12.2.4, Timer Control Register (TCR). 2. If the count input of channel 0 is the TCNT1 overflow signal and that of channel 1 is the TCNT0 compare-match signal, no incrementing clock will be generated. Do not use this setting. Rev. 3.00 Mar 17, 2006 page 664 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCSRX—Timer Control/Status Register X H'FFF1 TMRX TCSRX 7 6 5 4 3 2 1 0 CMFB CMFA OVF ICF OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/(W)* R/W R/W R/W R/W Bit Output Select 1 and 0 0 1 0 No change when compare-match A occurs 1 0 output when compare-match A occurs 0 1 output when compare-match A occurs 1 Output inverted when compare-match A occurs (toggle output) Output Select 3 and 2 0 0 1 0 output when compare-match B occurs 1 0 1 output when compare-match B occurs 1 Output inverted when compare-match B occurs (toggle output) No change when compare-match B occurs Input Capture Flag 0 [Clearing condition] When 0 is written in ICF after reading ICF = 1 1 [Setting condition] When a rising edge followed by a falling edge is detected in the external reset signal after the ICST bit in TCONRI has been set to 1 Timer Overflow Flag 0 [Clearing condition] When 0 is written in OVF after reading OVF = 1 1 [Setting condition] When TCNT overflows from H'FF to H'00 Compare-Match Flag A 0 [Clearing condition] When 0 is written in CMFA after reading CMFA = 1 1 [Setting condition] When TCNT = TCORA Compare-Match Flag B 0 [Clearing condition] When 0 is written in CMFB after reading CMFB = 1 1 [Setting condition] When TCNT = TCORB Note: * Only 0 can be written in bits 7 to 4, to clear the flags. Rev. 3.00 Mar 17, 2006 page 665 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCSRY—Timer Control/Status Register Y H'FFF1 TMRY TCSRY Bit 7 6 5 4 3 2 1 0 CMFB CMFA OVF ICIE OS3 OS2 OS1 OS0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/(W)* R/(W)* R/(W)* R/W R/W R/W R/W R/W Output Select 1 and 0 0 1 0 No change when compare-match A occurs 1 0 output when compare-match A occurs 0 1 output when compare-match A occurs 1 Output inverted when compare-match A occurs (toggle output) Output Select 3 and 2 0 1 0 No change when compare-match B occurs 1 0 output when compare-match B occurs 0 1 output when compare-match B occurs 1 Output inverted when compare-match B occurs (toggle output) Input Capture Interrupt Enable 0 ICF interrupt request (ICIX) is disabled 1 ICF interrupt request (ICIX) is enabled Timer Overflow Flag 0 [Clearing condition] When 0 is written in OVF after reading OVF = 1 1 [Setting condition] When TCNT overflows from H'FF to H'00 Compare-Match Flag A 0 [Clearing condition] When 0 is written in CMFA after reading CMFA = 1 1 [Setting condition] When TCNT = TCORA Compare-Match Flag B 0 [Clearing condition] When 0 is written in CMFB after reading CMFB = 1 1 [Setting condition] When TCNT = TCORB Note: * Only 0 can be written in bits 7 to 5, to clear the flags. Rev. 3.00 Mar 17, 2006 page 666 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TICRR—Input Capture Register R TICRF—Input Capture Register F H'FFF2 H'FFF3 TMRX TMRX Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R R R R R R R R Stores TCNT value at fall of external reset input TCORAY—Time Constant Register AY TCORBY—Time Constant Register BY H'FFF2 H'FFF3 TMRY TMRY TCORAY, TCORBY Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Compare-match flag (CMF) is set when TCOR and TCNT values match TCNTX—Timer Counter X TCNTY—Timer Counter Y H'FFF4 H'FFF4 TMRX TMRY Bit 7 6 5 4 3 2 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Up-counter Rev. 3.00 Mar 17, 2006 page 667 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TISR—Timer Input Select Register Bit H'FFF5 TMRY 7 6 5 4 3 2 1 0 — — — — — — — IS Initial value 1 1 1 1 1 1 1 0 Read/Write — — — — — — — R/W Input Select TCORC—Time Constant Register C TCORAX—Time Constant Register AX TCORBX—Time Constant Register BX 0 IVG signal is selected 1 TMIY (TMCIY/TMRIY) is selected H'FFF5 H'FFF6 H'FFF7 TMRX TMRX TMRX TCORC Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Compare-match C signal is generated when sum of TCORC and TICR contents match TCNT value TCORAX, TCORBX Bit 7 6 5 4 3 2 1 0 Initial value 1 1 1 1 1 1 1 1 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Compare-match flag (CMF) is set when TCOR and TCNT values match Rev. 3.00 Mar 17, 2006 page 668 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCONRI—Timer Connection Register I Bit 7 6 H'FFFC 5 SIMOD1 SIMOD0 SCONE Timer Connection 4 3 2 1 0 ICST HFINV VFINV HIINV VIINV Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Input Synchronization Signal Inversion 0 The VSYNCI pin state is used directly as the VSYNCI input 1 The VSYNCI pin state is inverted before use as the VSYNCI input Input Synchronization Signal Inversion 0 The HSYNCI and CSYNCI pin states are used directly as the HSYNCI and CSYNCI inputs 1 The HSYNCI and CSYNCI pin states are inverted before use as the HSYNCI and CSYNCI inputs Input Synchronization Signal Inversion 0 The VFBACKI pin state is used directly as the VFBACKI input 1 The VFBACKI pin state is inverted before use as the VFBACKI input Input Synchronization Signal Inversion 0 The HFBACKI pin state is used directly as the HFBACKI input 1 The HFBACKI pin state is inverted before use as the HFBACKI input Input Capture Start Bit 0 The TICRR and TICRF input capture functions are stopped [Clearing condition] When a rising edge followed by a falling edge is detected on TMRIX 1 The TICRR and TICRF input capture functions are operating (Waiting for detection of a rising edge followed by a falling edge on TMRIX) [Setting condition] When 1 is written in ICST after reading ICST = 0 Synchronization Signal Connection Enable SCONE Mode FTIA 0 Normal connection 1 Synchronization IVI signal connecsignal tion mode FTIA input FTID TMCI1 TMRI1 FTIB input FTIC input FTIC FTID input TMCI1 input TMRI1 input TMO1 signal VFBACKI input IHI signal IHI signal IVI inverse signal FTIB Input Synchronization Mode Select 1 and 0 SIMOD1 SIMOD0 IHI Signal IVI Signal 0 0 No signal HFBACKI input VFBACKI input 1 S-on-G mode CSYNCI input PDC input 0 Composite mode HSYNCI input PDC input 1 Separate mode HSYNCI input VSYNCI input 1 Mode Rev. 3.00 Mar 17, 2006 page 669 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCONRO—Timer Connection Register O Bit H'FFFD Timer Connection 7 6 5 4 3 2 HOE VOE CLOE CBOE HOINV VOINV 1 0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W CLOINV CBOINV Output Synchronization Signal Inversion 0 The CBLANK signal is used directly as the CBLANK output 1 The CBLANK signal is inverted before use as the CBLANK output Output Synchronization Signal Inversion 0 The CLO signal (CL1, CL2, CL3, or CL4 signal) is used directly as the CLAMPO output 1 The CLO signal (CL1, CL2, CL3, or CL4 signal) is inverted before use as the CLAMPO output Output Synchronization Signal Inversion 0 The IVO signal is used directly as the VSYNCO output 1 The IVO signal is inverted before use as the VSYNCO output Output Synchronization Signal Inversion 0 The IHO signal is used directly as the HSYNCO output 1 The IHO signal is inverted before use as the HSYNCO output Output Enable 0 [H8/3577 Group] The P27/PW15/CBLANK pin functions as the P27/PW15 pin [H8/3567 Group] The P15/PW5/CBLANK pin functions as the P15/PW5 pin 1 [H8/3577 Group] The P27/PW15/CBLANK pin functions as the CBLANK pin [H8/3567 Group] The P15/PW5/CBLANK pin functions as the CBLANK pin Output Enable 0 The P64/FTIC/TMO0/CLAMPO pin functions as the P64/FTIC/TMO0 pin 1 The P64/FTIC/TMO0/CLAMPO pin functions as the CLAMPO pin Output Enable 0 The P61/FTOA/VSYNCO pin functions as the P61/FTOA pin 1 The P61/FTOA/VSYNCO pin functions as the VSYNCO pin Output Enable 0 The P67/TMO1/TMOX/HSYNCO pin functions as the P67/TMO1/TMOX pin 1 The P67/TMO1/TMOX/HSYNCO pin functions as the HSYNCO pin Rev. 3.00 Mar 17, 2006 page 670 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers TCONRS—Timer Connection Register S 7 Bit 6 TMRX/Y 5 H'FFFE 4 3 Timer Connection 2 1 0 ISGENE HOMOD1 HOMOD0 VOMOD1 VOMOD0 CLMOD1 CLMOD0 Initial value 0 0 0 0 0 0 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Clamp Waveform Mode Select 1 and 0 ISGENE CLMOD1 CLMOD0 Description 0 0 The CL1 signal is selected 1 The CL2 signal is selected 0 The CL3 signal is selected 0 1 1 0 1 The CL4 signal is selected 0 1 1 0 1 Vertical Synchronization Output Mode Select 1 and 0 ISGENE VOMOD1 VOMOD0 0 0 1 1 0 Description 0 The IVI signal (without fall modification or IHI synchronization) is selected 1 The IVI signal (without fall modification, with IHI synchronization) is selected 0 The IVI signal (with fall modification, without IHI synchronization) is selected 1 The IVI signal (with fall modification and IHI synchronization) is selected 0 The IVG signal is selected 1 1 0 1 Horizontal Synchronization Output Mode Select 1 and 0 ISGENE HOMOD1 HOMOD0 0 0 1 Description 0 The IHI signal (without 2fH modification) is selected 1 The IHI signal (with 2fH modification) is selected 0 The CL1 signal is selected 1 1 0 0 The IHG signal is selected 1 1 0 1 Internal Synchronization Signal Select TMRX/TMRY Access Select 0 The TMRX registers are accessed at addresses H'FFF0 to H'FFF5 1 The TMRY registers are accessed at addresses H'FFF0 to H'FFF5 Rev. 3.00 Mar 17, 2006 page 671 of 706 REJ09B0303-0300 Appendix B Internal I/O Registers SEDGR—Edge Sense Register Bit 7 6 5 VEDG HEDG CEDG 0 0 0 Initial value Read/Write H'FFFF *1 R/(W) *1 R/(W) 4 R/(W) 2 3 HFEDG VFEDG PREQF 0 *1 Timer Connection 0 *1 R/(W) 0 *1 *1 R/(W) R/(W) 1 0 IHI IVI —*2 —*2 R R IVI Signal Level 0 The IVI signal is low 1 The IVI signal is high IHI Signal Level 0 The IHI signal is low 1 The IHI signal is high Pre-Equalization Flag 0 [Clearing condition] When 0 is written in PREQF after reading PREQF = 1 1 [Setting condition] When an IHI signal 2fH modification condition is detected VFBACKI Edge 0 [Clearing condition] When 0 is written in VFEDG after reading VFEDG = 1 1 [Setting condition] When a rising edge is detected on the VFBACKI pin HFBACKI Edge 0 [Clearing condition] When 0 is written in HFEDG after reading HFEDG = 1 1 [Setting condition] When a rising edge is detected on the HFBACKI pin CSYNCI Edge 0 [Clearing condition] When 0 is written in CEDG after reading CEDG = 1 1 [Setting condition] When a rising edge is detected on the CSYNCI pin HSYNCI Edge 0 [Clearing condition] When 0 is written in HEDG after reading HEDG = 1 1 [Setting condition] When a rising edge is detected on the HSYNCI pin VSYNCI Edge 0 [Clearing condition] When 0 is written in VEDG after reading VEDG = 1 1 [Setting condition] When a rising edge is detected on the VSYNCI pin Notes: 1. Only 0 can be written, to clear the flag. 2. The initial value is undefined since it depends on the pin states. Rev. 3.00 Mar 17, 2006 page 672 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Appendix C I/O Port Block Diagrams C.1 Port 1 Block Diagrams Reset * R D Q P1nPCR RP1P C WP1D Reset R D Q P1nDDR C WP1D Internal data bus Hardware standby Reset P1n 8-bit PWM PWM output enable PWM output R Q D P1nDR C WP1 14-bit PWM PWX0 and PWX1 output Output enable RP1 Legend: WP1D: Write to P1DDR WP1P: Write to P1PCR RP1P: Read P1PCR WP1: Write to port 1 RP1: Read port 1 Notes: n = 0 or 1 * MOS input pull-up applies to the H8/3577 Group only. Figure C.1 Port 1 Block Diagram (Pins P10 and P11) Rev. 3.00 Mar 17, 2006 page 673 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Reset * R D Q P1nPCR RP1P C WP1D Reset R D Q P1nDDR C WP1D Reset P1n Internal data bus Hardware standby 8-bit PWM PWM output enable PWM output R Q D P1nDR C WP1 RP1 Legend: WP1D: Write to P1DDR WP1P: Write to P1PCR RP1P: Read P1PCR WP1: Write to port 1 RP1: Read port 1 Notes: n = 2 to 7 * MOS input pull-up applies to the H8/3577 Group only. Figure C.2 Port 1 Block Diagram (Pins P12 to P17 in H8/3577 Group, Pins P12 to P14 in H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 674 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P15DDR C WP1D Reset P15 Internal data bus Appendix C I/O Port Block Diagrams 8-bit PWM PWM output enable PWM output R Q D P15DR C WP1 Timer connection CBLANK CBLANK output enable RP1 Legend: WP1D: Write to P1DDR WP1: Write to port 1 RP1: Read port 1 Figure C.3 Port 1 Block Diagram (Pin P15 in H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 675 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P16DDR C WP1D *1 Reset P16 R Q D P16DR C *2 WP1 Internal data bus Appendix C I/O Port Block Diagrams 8-bit PWM PWM output enable PWM output IIC1 SDA1 output Transmit enable RP1 SDA1 input Legend: WP1D: Write to P1DDR WP1: Write to port 1 RP1: Read port 1 Notes: 1. Output enable signal 2. Open drain control signal Figure C.4 Port 1 Block Diagram (Pin P16 in H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 676 of 706 REJ09B0303-0300 Hardware standby Mode 1 Reset S R D Q P17DDR C WP1D *1 Reset P17 R Q D P17DR C *2 WP1 Internal data bus Appendix C I/O Port Block Diagrams 8-bit PWM PWM output enable PWM output IIC1 SCL1 output Transmit enable RP1 SCL1 input Legend: WP1D: Write to P1DDR WP1: Write to port 1 RP1: Read port 1 Notes: 1. Output enable signal 2. Open drain control signal Figure C.5 Port 1 Block Diagram (Pin P17 in H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 677 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams C.2 Port 2 Block Diagrams Port 2 is provided only in the H8/3577 Group, and not in the H8/3567 Group. Reset Hardware standby WP2D Reset R D Q P2nDDR C WP2D Reset P2n Internal data bus R D Q P2nPCR RP2P C 8-bit PWM PWM output enable PWM output R Q D P2nDR C WP2 RP2 Legend: WP2D: Write to P2DDR WP2P: Write to P2PCR RP2P: Read P2PCR WP2: Write to port 2 RP2: Read port 2 Note: n = 0 to 2, 5, 6 Figure C.6 Port 2 Block Diagram (Pins P20 to P22, P25, and P26 in H8/3577 Group) Rev. 3.00 Mar 17, 2006 page 678 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Reset Hardware standby WP2D Reset R D Q P23DDR C WP2D *1 Reset P23 R Q D P23DR C *2 WP2 Internal data bus R D Q P23PCR RP2P C 8-bit PWM PWM output enable PWM output IIC1 SDA1 output Transmit enable RP2 SDA1 input Legend: WP2D: Write to P2DDR WP2P: Write to P2PCR RP2P: Read P2PCR WP2: Write to port 2 RP2: Read port 2 Notes: 1. Output enable signal 2. Open drain control signal Figure C.7 Port 2 Block Diagram (Pin P23 in H8/3577 Group) Rev. 3.00 Mar 17, 2006 page 679 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Reset Hardware standby WP2D Reset R D Q P24DDR C WP2D *1 Reset P24 R Q D P24DR C *2 WP2 Internal data bus R D Q P24PCR RP2P C 8-bit PWM PWM output enable PWM output IIC1 SCL1 output Transmit enable RP2 SCL1 input Legend: WP2D: Write to P2DDR WP2P: Write to P2PCR RP2P: Read P2PCR WP2: Write to port 2 RP2: Read port 2 Notes: 1. Output enable signal 2. Open drain control signal Figure C.8 Port 2 Block Diagram (Pin P24 in H8/3577 Group) Rev. 3.00 Mar 17, 2006 page 680 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Reset R D Q P27PCR C RP2P Reset R D Q P27DDR C WP2D P27 Reset Internal data bus WP2D Hardware standby 8-bit PWM PWM output enable PWM output R Q D P27DR C WP2 Timer connection CBLANK CBLANK output enable RP2 Legend: WP2D: Write to P2DDR WP2P: Write to P2PCR RP2P: Read P2PCR WP2: Write to port 2 RP2: Read port 2 Figure C.9 Port 2 Block Diagram (Pin P27 in H8/3577 Group) Rev. 3.00 Mar 17, 2006 page 681 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams C.3 Port 3 Block Diagram Port 3 is provided only in the H8/3577 Group, and not in the H8/3567 Group. Reset R D Q P3nPCR RP3P C Reset R D Q P3nDDR C WP3D Internal data bus WP3D Hardware standby Reset R Q D P3nDR C P3n WP3 RP3 Legend: WP3D: Write to P3DDR WP3P: Write to P3PCR RP3P: Read P3PCR WP3: Write to port 3 RP3: Read port 3 Note: n = 0 to 7 Figure C.10 Port 3 Block Diagram (Pins P30 to P37 in H8/3577 Group) Rev. 3.00 Mar 17, 2006 page 682 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Port 4 Block Diagrams Hardware standby Reset R D Q P40DDR C WP4D Internal data bus C.4 Reset R Q D P40DR C P40 WP4 RP4 A/D converter External trigger input IRQ2 input Legend: WP4D: Write to P4DDR WP4: Write to port 4 RP4: Read port 4 Figure C.11 Port 4 Block Diagram (Pin P40) Rev. 3.00 Mar 17, 2006 page 683 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P4nDDR C Internal data bus Appendix C I/O Port Block Diagrams WP4D Reset R Q D P4nDR C P4n WP4 RP4 IRQ1 input IRQ0 input Legend: WP4D: Write to P4DDR WP4: Write to port 4 RP4: Read port 4 Note: n = 1 or 2 Figure C.12 Port 4 Block Diagram (Pins P41 and P42) Rev. 3.00 Mar 17, 2006 page 684 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P4nDDR C Internal data bus Appendix C I/O Port Block Diagrams WP4D Reset R Q D P4nDR C P4n WP4 RP4 Legend: WP4D: Write to P4DDR WP4: Write to port 4 RP4: Read port 4 Note: n = 3 to 5 Figure C.13 Port 4 Block Diagram (Pins P43 to P45) Rev. 3.00 Mar 17, 2006 page 685 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P46DDR C Internal data bus Appendix C I/O Port Block Diagrams WP4D φ output P46 RP4 Legend: WP4D: Write to P4DDR RP4: Read port 4 Figure C.14 Port 4 Block Diagram (Pin P46) Rev. 3.00 Mar 17, 2006 page 686 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P47DDR C WP4D Internal data bus Appendix C I/O Port Block Diagrams Reset *1 R Q D P47DR C P47 *2 WP4 IIC0 SDA0 output Transmit enable RP4 SDA0 input Legend: WP4D: Write to P4DDR WP4: Write to port 4 RP4: Read port 4 Notes: 1. Output enable signal 2. Open drain control signal Figure C.15 Port 4 Block Diagram (Pin P47) Rev. 3.00 Mar 17, 2006 page 687 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Port 5 Block Diagrams Hardware standby Reset R D Q P50DDR C WP5D Internal data bus C.5 SCI0 Serial transmit data Output enable P50 Reset R Q D P50DR C WP5 RP5 Legend: WP5D: Write to P5DDR WP5: Write to port 5 RP5: Read port 5 Figure C.16 Port 5 Block Diagram (Pin P50) Rev. 3.00 Mar 17, 2006 page 688 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P51DDR C Internal data bus Appendix C I/O Port Block Diagrams WP5D SCI0 Input enable Reset R Q D P51DR C P51 WP5 RP5 Serial receive data Legend: WP5D: Write to P5DDR WP5: Write to port 5 RP5: Read port 5 Figure C.17 Port 5 Block Diagram (Pin P51) Rev. 3.00 Mar 17, 2006 page 689 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P52DDR C WP5D *1 Reset R Q D P52DR C P52 *2 WP5 Internal data bus Appendix C I/O Port Block Diagrams SCI0 Input enable Clock output Output enable Clock input IIC0 SCL0 output Transmit enable RP5 SCL0 input Legend: WP5D: Write to P5DDR WP5: Write to port 5 RP5: Read port 5 Notes: 1. Output enable signal 2. Open drain control signal Figure C.18 Port 5 Block Diagram (Pin P52) Rev. 3.00 Mar 17, 2006 page 690 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Port 6 Block Diagrams Hardware standby Reset R D Q P6nDDR C WP6D Internal data bus C.6 Reset R Q D P6nDR C P6n WP6 RP6 Legend: WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 16-bit FRT FTCI input FTIA input FTIB input FTID input Timer connection 8-bit timers 0 and 1 8-bit timers Y and X HFBACKI input, TMCI0 input TMIX input, VSYNCI input TMIY input, VFBACKI input TMRI0 input, HSYNCI input TMCI1 input Note: n = 0, 2, 3, 5 Figure C.19 Port 6 Block Diagram (Pins P60, P62, P63, and P65) Rev. 3.00 Mar 17, 2006 page 691 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P61DDR C WP6D Internal data bus Appendix C I/O Port Block Diagrams 16-bit FRT FTOA output Output enable Reset R Q D P61DR C P61 WP6 RP6 Legend: WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 Figure C.20 Port 6 Block Diagram (Pin P61) Rev. 3.00 Mar 17, 2006 page 692 of 706 REJ09B0303-0300 Timer connection VSYNCO output Output enable Hardware standby Reset R D Q P64DDR C WP6D Internal data bus Appendix C I/O Port Block Diagrams Timer connection CLAMPO output Output enable Reset R Q D P64DR C P64 WP6 8-bit timer 0 TMO0 output Output enable RP6 16-bit FRT FTIC input Legend: WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 Figure C.21 Port 6 Block Diagram (Pin P64) Rev. 3.00 Mar 17, 2006 page 693 of 706 REJ09B0303-0300 Hardware standby Reset R D Q P66DDR C WP6D Internal data bus Appendix C I/O Port Block Diagrams 16-bit FRT FTOB output Output enable Reset P66 R Q D P66DR C WP6 RP6 Legend: WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 Figure C.22 Port 6 Block Diagram (Pin P66) Rev. 3.00 Mar 17, 2006 page 694 of 706 REJ09B0303-0300 8-bit timer 1 timer connection TMRI1 input CSYNCI input Hardware standby Reset R D Q P67DDR C WP6D Internal data bus Appendix C I/O Port Block Diagrams 8-bit timer X TMOX output Output enable Reset R Q D P67DR C P67 WP6 8-bit timer 1 TMO1 output Output enable Timer connection HSYNCO output Output enable RP6 Legend: WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 Figure C.23 Port 6 Block Diagram (Pin P67) Rev. 3.00 Mar 17, 2006 page 695 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams C.7 Port 7 Block Diagram RP7 P7n Internal data bus The H8/3577 Group has an 8-bit input port (pins P70 to P77) and the H8/3567 Group has a 4-bit input port (pins P70 to P73). A/D converter Analog input Legend: RP7: Read port 7 Note: n = 0 to 7 Figure C.24 Port 7 Block Diagram (Pins P70 to P77 in H8/3577 Group, Pins P70 to P73 in H8/3567 Group) Rev. 3.00 Mar 17, 2006 page 696 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams C.8 Port 8 Block Diagrams Port C is provided only in the H8/3567 Group version with an on-chip USB. Hardware standby Reset R D Q PCnDDR C Internal data bus RPCO WPCD Reset R Q D PCnODR C PCn WPC USB ENP output Output enable RPC Legend: WPCD: Write to PCDDR WPC: Write to port C RPC: Read port C RPCO: Read to ODR Note: n = 0 to 3 Figure C.25 Port C Block Diagram (Pins PC0 to PC3 in H8/3567 Group Version with On-Chip USB) Rev. 3.00 Mar 17, 2006 page 697 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams Hardware standby Reset R D Q PCnDDR C WPCD Internal data bus RPCO Reset R Q D PCnODR C PCn WPC RPC USB OCP input Input enable Legend: WPCD: Write to PCDDR WPC: Write to port C RPC: Read port C RPCO: Read to ODR Note: n = 4 to 7 Figure C.26 Port C Block Diagram (Pins PC4 to PC7 in H8/3567 Group Version with On-Chip USB) Rev. 3.00 Mar 17, 2006 page 698 of 706 REJ09B0303-0300 Appendix C I/O Port Block Diagrams C.9 Port D Block Diagram Port D is provided only in the H8/3567 Group version with an on-chip USB. USB FONLY bit Hardware standby Reset R D Q PDnDDR C Internal data bus RPDO WPDD Reset R Q D PDnODR C PDn WPD RPC DSmD+/DSMDLegend: WPDD: Write to PDDDR WPD: Write to port D RPD: Read port D RPDO: Read to ODR USB bus driver/ receiver Note: n = 0 to 7 m = 2 to 5 Figure C.27 Port D Block Diagram (Pins PD0 to PD7 in H8/3567 Group Version with On-Chip USB) Rev. 3.00 Mar 17, 2006 page 699 of 706 REJ09B0303-0300 Appendix D Pin States Appendix D Pin States D.1 Port States in Each Mode Table D.1 I/O Port States in Each Processing State Port Name Pin Name Reset Hardware Standby Mode Software Standby Mode Program Execution State Port 1 T T kept I/O port Port 2 T T kept I/O port Port 3 T T kept I/O port Port 47 T T kept I/O port Port 46 T T [DDR = 1] H Clock output/input port [DDR = 0] T Port 45 to 40 T T kept I/O port Port 5 T T kept I/O port Port 6 T T kept I/O port Port 7 T T T Input port Port C T T Functioning (HOCnE = 1) USB input/output I/O port kept (HOCnE = 0) Port D T T Functioning (FONLY = 0) USB input/output I/O port kept (FONLY = 1) Legend: H: High level L: Low level T: High impedance kept: Input pins are in the high-impedance state (when DDR = 0 and PCR = 1, MOS input pullups remain in the on state). Output ports retain their state. In some cases, the on-chip supporting module is initialized and the pin is an input/output port, determined by the DDR and DR settings. DDR: Data direction register HOCnE: HOCnE bit in HOCCR of USB FONLY: FONLY bit in USBCR of USB Note: n = 2 to 5 Rev. 3.00 Mar 17, 2006 page 700 of 706 REJ09B0303-0300 Appendix E Timing of Transition to and Recovery from Hardware Standby Mode Appendix E Timing of Transition to and Recovery from Hardware Standby Mode E.1 Timing of Transition to Hardware Standby Mode (1) To retain RAM contents when the RAME bit in SYSCR is set to 1, drive the RES signal low 10 system clock cycles before the STBY signal goes low, as shown in figure E.1. RES must remain low until STBY goes low (minimum delay from STBY low to RES high: 0 ns). STBY t1 ≥ 10tcyc t2 ≥ 0 ns RES Figure E.1 Timing of Transition to Hardware Standby Mode (2) When the RAME bit in SYSCR is cleared to 0 or when it is not necessary to retain RAM contents, RES does not have to be driven low as in (1). E.2 Timing of Recovery from Hardware Standby Mode Drive the RES signal low approximately 100 ns or more before STBY goes high. STBY t ≥ 100 ns tOSC RES Figure E.2 Timing of Recovery from Hardware Standby Mode Rev. 3.00 Mar 17, 2006 page 701 of 706 REJ09B0303-0300 Appendix F Product Code Lineup Appendix F Product Code Lineup Table F.1 H8/3577 Group and H8/3567 Group Product Code Lineup Product Type H8/3577 H8/3577 Group ZTAT version Mask ROM version H8/3574 H8/3567 H8/3567 Group H8/3564 Product Code Mark Code Package (Package Code) HD6473577 HD6473577P20 64-pin shrink DIP (DP-64S) HD6476577F20 64-pin QFP (FP-64A) HD6433577 HD6433577(***)P20 64-pin shrink DIP (DP-64S) HD6433577(***)F20 64-pin QFP (FP-64A) 64-pin shrink DIP (DP-64S) Mask ROM version HD6433574 HD6433574(***)P20 HD6433574(***)F20 64-pin QFP (FP-64A) ZTAT version HD6473567 HD6473567P20 42-pin shrink DIP (DP-42S) Mask ROM version HD6433567 Mask ROM version HD6433564 (10 MHz limit version) H8/3567U ZTAT version (on-chip USB) HD6476567F20 44-pin QFP (FP-44A) HD6433567(***)P20 42-pin shrink DIP (DP-42S) HD6433567(***)F20 44-pin QFP (FP-44A) HD6433564(***)P20 42-pin shrink DIP (DP-42S) HD6433564(***)F20 44-pin QFP (FP-44A) HD6433564(***)P10 HD6473567U HD6473567UP20 HD6473567UF20 42-pin shrink DIP (DP-42S) 64-pin shrink DIP (DP-64S) 64-pin QFP (FP-64A) Mask ROM version (on-chip USB) HD6433567U HD6433567U(***)P20 64-pin shrink DIP (DP-64S) H8/3564U Mask ROM version (on-chip USB) HD6433564U HD6433564U(***)P20 64-pin shrink DIP (DP-64S) HD6433567U(***)F20 64-pin QFP (FP-64A) HD6433564U(***)F20 64-pin QFP (FP-64A) Note: (***) is the ROM code. When ordering, the frequency selection (20 or 10) is not indicated by the model name, but is identified by the ROM code. Rev. 3.00 Mar 17, 2006 page 702 of 706 REJ09B0303-0300 Appendix G Package Dimensions Appendix G Package Dimensions Figures G.1 to G.4 show package dimensions of H8/3577 Group and H8/3567 Group. JEITA Package Code P-SDIP64-17x57.6-1.78 RENESAS Code PRDP0064BB-A Previous Code DP-64S/DP-64SV MASS[Typ.] 8.8g D 33 E 64 1 32 b3 Reference Dimension in Millimeters Symbol Min L A1 A Z e bp θ c e1 e1 D E A A1 bp b3 c θ e Z L Nom Max 19.05 57.6 58.5 17.0 18.6 5.08 0.51 0.38 0.48 0.58 1.0 0.20 0.25 0.36 0° 15° 1.53 1.78 2.03 1.46 2.54 Figure G.1 DP-64S Package Dimensions Rev. 3.00 Mar 17, 2006 page 703 of 706 REJ09B0303-0300 Appendix G Package Dimensions JEITA Package Code P-QFP64-14x14-0.80 RENESAS Code PRQP0064GB-A Previous Code FP-64A/FP-64AV MASS[Typ.] 1.2g HD *1 D 48 33 NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 32 49 bp c c1 HE *2 E b1 Reference Dimension in Millimeters Symbol Terminal cross section ZE Min 17 64 16 c F A ZD A2 1 θ A1 L L1 Detail F e *3 y bp x M Figure G.2 FP-64A Package Dimensions Rev. 3.00 Mar 17, 2006 page 704 of 706 REJ09B0303-0300 D E A2 HD HE A A1 bp b1 c c1 θ e x y ZD ZE L L1 Nom Max 14 14 2.70 16.9 17.2 17.5 16.9 17.2 17.5 3.05 0.00 0.10 0.25 0.29 0.37 0.45 0.35 0.12 0.17 0.22 0.15 0° 8° 0.8 0.15 0.10 1.0 1.0 0.5 0.8 1.1 1.6 Appendix G Package Dimensions JEITA Package Code P-SDIP42-14x37.3-1.78 RENESAS Code PRDP0042BB-A Previous Code DP-42S/DP-42SV MASS[Typ.] 4.8g D 22 E 42 1 21 b3 A Reference Dimension in Millimeters Symbol Min L A1 Z e bp θ c e1 e1 D E A A1 bp b3 c θ e Z L Nom Max 15.24 37.3 38.6 14.0 14.6 5.10 0.51 0.38 0.48 0.58 1.0 0.20 0.25 0.35 0° 15° 1.53 1.78 2.03 1.38 2.54 Figure G.3 DP-42S Package Dimensions Rev. 3.00 Mar 17, 2006 page 705 of 706 REJ09B0303-0300 Appendix G Package Dimensions JEITA Package Code P-QFP44-14x14-0.80 RENESAS Code PRQP0044GC-A Previous Code FP-44A/FP-44AV MASS[Typ.] 1.2g HD *1 D 33 23 NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 34 bp 22 c c1 HE *2 E b1 Reference Dimension in Millimeters Symbol Terminal cross section 12 44 ZE Min c F A2 11 A 1 ZD θ A1 L L1 Detail F e *3 bp x M y Figure G.4 FP-44A Package Dimensions Rev. 3.00 Mar 17, 2006 page 706 of 706 REJ09B0303-0300 D E A2 HD HE A A1 bp b1 c c1 θ e x y ZD ZE L L1 Nom Max 14 14 2.70 16.9 17.2 17.5 16.9 17.2 17.5 3.05 0.00 0.10 0.25 0.29 0.37 0.45 0.35 0.12 0.17 0.22 0.15 0° 8° 0.8 0.15 0.10 3.0 3.0 0.5 0.8 1.1 1.6 Renesas 8-Bit Single-Chip Microcomputer Hardware Manual H8/3577 Group, H8/3567 Group Publication Date: 1st Edition, September 1999 Rev.3.00, March 17, 2006 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. ©2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 Colophon 6.0 H8/3577 Group, H8/3567 Group Hardware Manual