AD ADM8697 Microprocessor supervisory circuit Datasheet

a
FEATURES
Upgrade for ADM696/ADM697, MAX696/MAX697
Specified Over Temperature
Adjustable Low Line Voltage Monitor
Power OK/Reset Time Delay
Reset Assertion Down to 1 V VCC
Watchdog Timer—100 ms, 1.6 s, or Adjustable
Low Switch On Resistance
0.7 V Normal, 7 V in Backup
400 nA Standby Current
Automatic Battery Backup Switching (ADM8696)
Fast On-Board Gating of Chip Enable Signals (ADM8697)
Voltage Monitor for Power Fail or Low Battery Warning
Also Available in TSSOP Package
Qualified for Automotive Applications
APPLICATIONS
Microprocessor Systems
Computers
Controllers
Intelligent Instruments
Automotive Systems
Critical µP Power Monitoring
GENERAL DESCRIPTION
The ADM8696/ADM8697 supervisory circuits offer complete
single chip solutions for power supply monitoring and battery
control functions in microprocessor systems. These functions
include µP reset, backup battery switchover, watchdog timer,
CMOS RAM write protection and power failure warning.
The ADM8696/ADM8697 are available in 16-pin DIP and small
outline packages (including TSSOP) and provide the following
functions:
1. Power-On Reset output during power-up, power-down and
brownout conditions. The RESET voltage threshold is
adjustable using an external voltage divider. The RESET output remains operational with VCC as low as 1 V.
2. A Reset pulse if the optional watchdog timer has not been
toggled within specified time.
Microprocessor
Supervisory Circuits
ADM8696/ADM8697
FUNCTIONAL BLOCK DIAGRAMS
BATT ON
VBATT
VOUT
VCC
LLIN
LOW LINE
RESET
RESET GENERATOR
RESET
OSC IN
OSC SEL
TIMEBASE FOR RESET
AND WATCHDOG
WATCHDOG
INPUT (WDI)
WATCHDOG
TRANSITION DETECTOR
WATCHDOG
TIMER
WATCHDOG
OUTPUT (WDO)
ADM8696
POWER FAIL
INPUT (PFI)
POWER FAIL
OUTPUT (PFO)
1.3V
CEIN
CEOUT
LLIN
LOW LINE
RESET
RESET GENERATOR
RESET
OSC IN
TIMEBASE FOR RESET
AND WATCHDOG
OSC SEL
WATCHDOG
TIMER
WATCHDOG
INPUT (WDI)
WATCHDOG
OUTPUT (WDO)
WATCHDOG
TRANSITION DETECTOR
ADM8697
POWER FAIL
INPUT (PFI)
1.3V
POWER FAIL
OUTPUT (PFO)
3. Separate watchdog timeout and low line status outputs.
4. Adjustable reset and watchdog timeout periods.
5. A 1.3 V threshold detector for power fail warning, low battery
detection or to monitor a power supply other than VCC.
6. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power logic (ADM8696).
7. Write protection of CMOS RAM or EEPROM (ADM8697).
The ADM8696/ADM8697 is fabricated using an advanced
epitaxial CMOS process combining low power consumption
(0.7 mW), extremely fast Chip Enable gating (2 ns) and high reliability. RESET assertion is guaranteed with VCC as low as 1 V.
In addition, the power switching circuitry is designed for minimal voltage drop thereby permitting increased output current drive
of up to 100 mA without the need for an external pass transistor.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
World Wide Web Site: http://www.analog.com
©1997-2010 Analog Devices, Inc. All rights reserved.
Fax: 617/326-8703
Operating Range, V
ADM8696/ADM8697–SPECIFICATIONS (Vunless= Fullotherwise
noted.)
CC
Parameter
VCC Operating Voltage Range
VBATT Operating Voltage Range
BATTERY BACKUP SWITCHING (ADM8696)
VOUT Output Voltage
VOUT in Battery Backup Mode
Supply Current (Excludes IOUT)
Supply Current in Battery Backup Mode
Battery Standby Current
(+ = Discharge, – = Charge)
Battery Switchover Threshold
VCC – VBATT
Battery Switchover Hysteresis
BATT ON Output Voltage
BATT ON Output Short Circuit Current
Min
3.0
2.0
Watchdog Timeout Period, External Clock
Minimum WDI Input Pulse Width
Max
Units
5.5
VCC – 0 3
V
V
–0.1
µA
mV
mV
mV
V
mA
µA
ISINK = 3.2 mA
BATT ON = VOUT = 2.4 V Sink Current
BATT ON = VOUT, VCC = 0 V, Source Current
V
ms
s
ms
Cycles
Cycles
ns
ns
ns
mV
V
V
V
V
V
V
V
µA
OSC SEL = HIGH
Long Period
Short Period
Long Period
Short Period
VIL = 0.8, VIH = 3.75 V, VCC = 5 V
VIL = 0.8, VIH = 3.5 V, VCC = 5 V
VIL = 0.8, VIH = 2.6 V, VCC = 3 V
ISINK = 10 µA, VCC = 1 V
ISINK = 400 µA, VCC = 2 V, VBATT = 0 V
ISINK = 3.2 mA, 3 V < VCC < 5.5 V
ISOURCE = 1 µA, VCC = 5 V
ISOURCE = 1 µA, VCC = 3 V
ISINK = 3.2 mA,
ISOURCE = 1 µA, VCC = 5 V
ISOURCE = 1 µA, VCC = 3 V
VCC = 5 V
V
V
V
µA
µA
VCC = 5 V
VCC = 3 V
WD1 = VOUT, (VCC)
WD1 = 0 V
V
mV
nA
nA
V
V
V
µA
ISINK = 3.2 mA
ISOURCE = 1 µA
ISOURCE = 1 µA, VCC = 3 V
PFI = Low, PFO = 0 V
+0.02
70
50
20
0.3
1.25
35
1.0
70
4032
960
50
100
30
2.5
25
1.3
50
1.6
100
4063
1011
1.35
70
2.25
140
4097
1025
100
4
0.1
0.1
20
0.4
0.4
3.5
2.7
LOW LINE, WDO Output Voltage
0.4
3.5
1
2.7
10
25
0.8
3.5
–10
1.2
1
–1
1.2
–50
–25
–50
1.3
± 15
± 0.01
± 0.01
WDI Input Current
POWER FAIL DETECTOR
PFI Input Threshold
PFI–LLIN Threshold Difference
PFI Input Current
LLIN Input Current
PFO Output Voltage
10
1.4
+50
+25
+50
0.4
3.5
PFO Short Circuit Source Current
1
2.7
10
25
CHIP ENABLE GATING (ADM8697)
CEIN Threshold
0.8
3.0
1.2
3
CEIN Pull-Up Current
CEOUT Output Voltage
0.4
VCC – 0.5
CE Propagation Delay
OSCILLATOR
OSC IN Input Current
OSC SEL Input Pull-Up Current
OSC IN Frequency Range
OSC IN Frequency with Ext. Capacitor
Test Conditions/Comments
V
V
V
µA
µA
RESET Output Voltage @ VCC = +1 V
RESET, RESET Output Voltage
Output Short Circuit Source Current
WDI Input Threshold1
Logic Low
Logic High
= +2.8 V, TA = TMIN to TMAX
VCC – 0.005
VCC – 0.0025
VCC – 0.125
VCC – 0.2
VBATT – 0.005 VBATT – 0.002
115
200
0.4
1
0.5
RESET AND WATCHDOG TIMER
Low Line Threshold (LLIN)
Reset Timeout Delay
Watchdog Timeout Period, Internal Oscillator
Typ
BATT
2
4
7
±2
5
0
500
4
IOUT = 1 mA
IOUT ≤ 100 mA
IOUT = 250 µA, VCC < VBATT – 0.2 V
IOUT = 100 mA
VCC = 0 V, VBATT = 2.8 V
5.5 V > VCC > VBATT + 0.2 V
Power-Up
Power-Down
V
V
V
µA
V
V
ns
ns
VIL
VIH
VCC = 3 V
ISINK = 3.2 mA
ISOURCE = 800 µA
VCC = 5.0 V
VCC = 3.0 V
µA
µA
kHz
kHz
OSC SEL = 0 V
OSC SEL = 0 V, COSC = 47 pF
NOTE
1
WDI is a three-level input internally biased to 38% of V CC and has an input impedance of approximately 5 MΩ.
Specifications subject to change without notice.
–2–
REV. A
ADM8696/ADM8697
ABSOLUTE MAXIMUM RATINGS*
(TA = +25°C unless otherwise noted)
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
VBATT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
All Other Inputs . . . . . . . . . . . . . . . . . . –0.3 V to VOUT + 0.5 V
Input Current
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA
VBATT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Power Dissipation, N-16 DIP . . . . . . . . . . . . . . . . . . . 600 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 135°C/W
Power Dissipation, RU-16 TSSOP . . . . . . . . . . . . . . . 500 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 158°C/W
Power Dissipation, R-16 SOIC . . . . . . . . . . . . . . . . . . 600 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 110°C/W
Operating Temperature Range
Industrial (A Version) . . . . . . . . . . . . . . . . . –40°C to +85°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . +300°C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum ratings for
extended periods of time may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADM8696/ADM8697 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
PIN CONFIGURATIONS
1
16 RESET
VOUT
2
15 RESET
VCC
3
GND
4
VBATT
REV. A
–3–
ADM8696
TOP VIEW
(Not to Scale)
14 WDO
13 LL IN
12 NC
BATT ON
5
LOW LINE
6
11 WDI
OSC IN
7
10 PFO
OSC SEL
8
9
TEST
1
16 RESET
NC
2
15 RESET
VCC
3
LL IN
4
GND
5
ADM8697
TOP VIEW
(Not to Scale)
PFI
14 WDO
13 CEIN
12 CEOUT
LOW LINE
6
11 WDI
OSC IN
7
10 PFO
OSC SEL
8
9
PFI
ADM8696/ADM8697
PIN FUNCTION DESCRIPTION
Mnemonic
Pin No.
ADM8696 ADM8697 Function
VCC
VBATT
VOUT
3
1
2
3
—
—
GND
RESET
4
15
5
15
WDI
11
11
PFI
9
9
PFO
10
10
CEIN
CEOUT
—
—
13
12
BATT ON
5
—
LOW LINE 6
6
RESET
OSC SEL
16
8
16
8
OSC IN
7
7
WDO
14
14
NC
LLIN
12
13
2
4
TEST
—
1
Power Supply Input +3 V to +5 V.
Backup Battery Input.
Output Voltage, VCC or VBATT is internally switched to VOUT depending on which is at
the highest potential. When VCC is higher than VBATT and LLIN is higher than the reset
threshold, VCC is switched to VOUT. When VCC is lower than VBATT and LLIN is below the
reset threshold, VBATT is switched to VOUT. VOUT can supply up to 100 mA to power CMOS
RAM. Connect VOUT to VCC if VOUT and VBATT are not used.
0 V. Ground reference for all signals.
Logic Output. RESET goes low whenever LLIN falls below 1.3 V and remains low for 50 ms
after LLIN goes above 1.3 V. RESET also goes low for 50 ms if the watchdog timer is enabled but not serviced within its timeout period. The RESET pulse width can be adjusted as
shown in Table I.
Watchdog Input, WDI is a three level input. If WDI remains either high or low for longer
than the watchdog timeout period, RESET pulses low and WDO goes low. The timer resets
with each transition at the WDI input. The watchdog timer is disabled when WDI is left
floating or is driven to midsupply.
Power Fail Input. PFI is the noninverting input to the Power Fail Comparator when PFI is
less than 1.3 V, PFO goes low. Connect PFI to GND or VOUT when not used. See Figure 1.
Power Fail Output. PFO is the output of the Power Fail Comparator. It goes low when PFI
is less than 1.3 V. The comparator is turned off and PFO goes low when VCC is below
VBATT.
Logic Input. The input to the CE gating circuit. Connect to GND or VOUT if not used.
Logic Output. CEOUT is a gated version of the CEIN signal. CEOUT tracks CEIN when LLIN
is above 1.3 V. If LLIN is below 1.3 V, CEOUT is forced high.
Logic Output. BATT ON goes high when VOUT is internally switched to the VBATT input.
It goes low when VOUT is internally switched to VCC. The output typically sinks 7 mA and
can directly drive the base of an external PNP transistor to increase the output current above
the 100 mA rating of VOUT.
Logic Output. LOW LINE goes low when LLIN falls below 1.3 V. It returns high as soon as
LLIN rises above 1.3 V.
Logic Output. RESET is an active high output. It is the inverse of RESET.
Logic Oscillator Select Input. When OSC SEL is unconnected or driven high, the internal
oscillator sets the reset time delay and watchdog timeout period. When OSC SEL is low, the
external oscillator input, OSC IN, is enabled. OSC SEL has a 3 µA internal pull-up. See
Table I and Figure 4.
Logic Oscillator Input. When OSC SEL is low, OSC IN can be driven by an external clock
to adjust both the reset delay and the watchdog timeout period. The timing can also be
adjusted by connecting an external capacitor to this pin. See Table I and Figure 4. When
OSC SEL is high or floating, OSC IN selects between fast and slow watchdog timeout periods.
Logic Output. The Watchdog Output, WDO, goes low if WDI remains either high or low
for longer than the watchdog timeout period. WDO is set high by the next transition at
WDI. If WDI is unconnected or at midsupply, WDO remains high. WDO also goes high
when LOW LINE goes low.
No Connect. It should be left open.
Voltage Sensing Input. The voltage on the low line input, LLIN, is compared with a 1.3 V
reference voltage. This input is normally used to monitor the power supply voltage. The
output of the comparator generates a LOW LINE output signal. It also generates a
RESET/RESET output. The comparator output also controls the battery switchover circuitry.
This is a special test pin using during device manufacture. It should be connected to GND.
–4–
REV. A
ADM8696/ADM8697
CIRCUIT INFORMATION
Battery Switchover Section (ADM8696)
Low Line RESET OUTPUT
RESET is an active low output that provides a RESET signal to
the microprocessor whenever the Low Line Input (LLIN) is below 1.3 V. The LLIN input is normally used to monitor the
power supply voltage. An internal timer holds RESET low for
50 ms after the voltage on LLIN rises above 1.3 V. This is intended as a power-on RESET signal for the processor. It allows
time for the power supply and microprocessor to stabilize. On
power-down, the RESET output remains low, with VCC as low
as 1 V. This ensures that the microprocessor is held in a stable
shutdown condition.
The battery switchover circuit is designed to switch over to
battery backup in the event of a power failure. When LLIN
is below the reset threshold and VCC is below VBATT, then
VBATT is switched to VOUT.
During normal operation, with VCC higher than VBATT, VCC is
internally switched to VOUT via an internal PMOS transistor
switch. This switch has a typical on resistance of 0.7 Ω and can
supply up to 100 mA at the VOUT terminal. VOUT is normally
used to drive a RAM memory bank which may require instantaneous currents of greater than 100 mA. If this is the case, then
a bypass capacitor should be connected to VOUT. The capacitor
will provide the peak current transients to the RAM. A capacitance value of 0.1 µF or greater may be used.
The LLIN comparator has approximately 12 mV of hysteresis
for enhanced noise immunity.
In addition to RESET, an active high RESET output is also
available. This is the complement of RESET and is useful for
processors requiring an active high RESET.
If the continuous output current requirement at VOUT exceeds
100 mA or if a lower VCC–VOUT voltage differential is desired,
an external PNP pass transistor may be connected in parallel
with the internal transistor. The BATT ON output can directly
drive the base of the external transistor.
LLIN
A 7 Ω MOSFET switch connects the VBATT input to VOUT during battery backup. This MOSFET has very low input-to-output differential (dropout voltage) at the low current levels
required for battery backup of CMOS RAM or other low power
CMOS circuitry. The supply current in battery backup is typically 0.4 µA.
RESET
Watchdog Timer RESET
The watchdog timer circuit monitors the activity of the microprocessor in order to check that it is not stalled in an indefinite
loop. An output line on the processor is used to toggle the
Watchdog Input (WDI) line. If this line is not toggled within
the selected timeout period, a RESET pulse is generated. The
ADM8696/ADM8697 may be configured for either a fixed
“short” 100 ms or a “long” 1.6 second timeout period or for an
adjustable timeout period. If the “short” period is selected,
some systems may be unable to service the watchdog timer immediately after a reset, so a “long” timeout is automatically initiated directly after a reset is issued. The watchdog timer is
restarted at the end of Reset, whether the Reset was caused by
lack of activity on WDI or by LLIN falling below the reset
threshold.
The normal (short) timeout period becomes effective following
the first transition of WDI after RESET has gone inactive. The
watchdog timeout period restarts with each transition on the
WDI pin. To ensure that the watchdog timer does not time out,
either a high-to-low or low-to-high transition on the WDI pin
must occur at or less than the minimum timeout period. If WDI
remains permanently either high or low, reset pulses will be issued after each timeout period (1.6 s). The watchdog monitor
can be deactivated by floating the Watchdog Input (WDI) or by
connecting it to midsupply.
BATT ON
(ADM8691, ADM8693,
ADM8695, ADM8696)
INTERNAL
SHUTDOWN SIGNAL
WHEN
VBATT > (VCC + 0.7V)
Figure 1. Battery Switchover Schematic
REV. A
t1
Figure 2. Power-Fail Reset Timing
GATE DRIVE
700
mV
t1
V1
V1 = RESET VOLTAGE THRESHOLD LOW
V2 = RESET VOLTAGE THRESHOLD HIGH
HYSTERESIS = V2–V1
VOUT
100
mV
V2
t1 = RESET TIME
If the battery switchover section is not used, VBATT should be
connected to GND and VOUT should be connected to VCC.
VBATT
V1
LOW LINE
The ADM8696 operates with battery voltages from 2.0 V to
VCC–0.3 V). High value capacitors, either standard electrolytic
or the farad-size double layer capacitors, can also be used for
short-term memory backup. A small charging current of typically 10 nA (0.1 µA max) flows out of the VBATT terminal. This
current is useful for maintaining rechargeable batteries in a fully
charged condition. This extends the life of the backup battery
by compensating for its self-discharge current. Also note that
this current poses no problem when lithium batteries are used
for backup since the maximum charging current (0.1 µA) is safe
for even the smallest lithium cells.
VCC
V2
–5–
ADM8696/ADM8697
Table I. ADM8696, ADM8697 Reset Pulse Width and Watchdog Timeout Selections
Watchdog Timeout Period
Immediately After Reset
OSC SEL
OSC IN
Normal
Low
Low
Floating or High
Floating or High
External Clock Input
External Capacitor
Low
Floating or High
1024 CLKS
400 ms × C/47 pF
100 ms
1.6 s
Reset Active Period
4096 CLKS
1.6 s × C/47 pF
1.6 s
1.6 s
512 CLKS
200 ms × C/47 pF
50 ms
50 ms
NOTE
With the OSC SEL pin low, OSC IN can be driven by an external clock signal, or an external capacitor can be connected between OSC IN and GND. The nominal
internal oscillator frequency is 10.24 kHz. The nominal oscillator frequency with external capacitor is: F OSC (Hz) = 184,000/C (pF).
WDI
8
OSC SEL
ADM869x
7 OSC IN
WDO
COSC
t3
t2
Figure 4b. External Capacitor
RESET
t1
t1
t1
t1 = RESET TIME
t2 = NORMAL (SHORT) WATCHDOG TIMEOUT PERIOD
t3 = WATCHDOG TIMEOUT PERIOD IMMEDIATELY FOLLOWING A RESET
NC
8
NC
7 OSC IN
OSC SEL
ADM869x
Figure 3. Watchdog Timeout Period and Reset Active Time
The watchdog timeout period defaults to 1.6 s and the reset
pulse width defaults to 50 ms, but these times to be adjusted as
shown in Table I. Figure 4 shows the various oscillator configurations that can be used to adjust the reset pulse width and
watchdog timeout period.
The internal oscillator is enabled when OSC SEL is high or
floating. In this mode, OSC IN selects between the 1.6 second
and 100 ms watchdog timeout periods. In either case, immediately after a reset the timeout period is 1.6 s. This gives the microprocessor time to reinitialize the system. If OSC IN is low,
the 100 ms watchdog period becomes effective after the first
transition of WDI. The software should be written such that the
I/O port driving WDI is left in its power-up reset state until the
initialization routines are completed and the microprocessor is
able to toggle WDI at the minimum watchdog timeout period of
70 ms.
8
Figure 4c. Internal Oscillator (1.6 s Watchdog)
NC
8
OSC SEL
ADM869x
7 OSC IN
Figure 4d. Internal Oscillator (100 ms Watchdog)
Watchdog Output (WDO)
The Watchdog Output WDO provides a status output that goes
low if the watchdog timer “times out” and remains low until set
high by the next transition on the watchdog input. WDO is also
set high when LLIN goes below the reset threshold.
OSC SEL
ADM869x
CLOCK
0 TO 500kHz
7 OSC IN
Figure 4a. External Clock Source
–6–
REV. A
ADM8696/ADM8697
CE Gating and RAM Write Protection (ADM8697)
can be chosen such that the voltage at PFI falls below 1.3 V
several milliseconds before the +5 V power supply falls below
the reset threshold. PFO is normally used to interrupt the
microprocessor so that data can be stored in RAM and the shutdown procedure executed before power is lost.
The ADM8697 contains memory protection circuitry that
ensures the integrity of data in memory by preventing write
operations when LLIN is below the threshold voltage. When
LLIN is greater than 1.3 V, CEOUT is a buffered replica of CEIN,
with a 2 ns propagation delay. When LLIN falls below the 1.3 V
threshold, an internal gate forces CEOUT high, independent of
CEIN.
INPUT
POWER
R1
CEOUT typically drives the CE, CS or Write input of battery
backed up CMOS RAM. This ensures the integrity of the data
in memory by preventing write operations when VCC is at an invalid level.
R2
CEIN
CEOUT
Figure 5. Chip Enable Gating
RESET
PFO
POWER
FAIL
INPUT
POWER
FAIL
OUTPUT
Table II. Input and Output Status In Battery Backup Mode
LLIN LOW = 0
LLIN OK = 1
V2
1.3V
Figure 7. Power Fail Comparator
ADM8697
LLIN
ADM869x
V2
Status
VOUT
(ADM8696) VOUT is connected to VBATT via an
internal PMOS switch.
RESET
Logic low.
RESET
Logic high. The open circuit output voltage is
equal to VOUT.
LOW LINE
Logic low.
BATT ON
(ADM8696) Logic high. The open circuit voltage is equal to VOUT.
WDI
WDI is ignored. It is internally disconnected
from the internal pull-up resistor and does not
source or sink current as long as its input voltage
is between GND and VOUT. The input voltage
does not affect supply current.
WDO
Logic high. The open circuit voltage is equal to
VOUT.
PFI
The Power Fail Comparator is turned off and
has no effect on the Power Fail Output.
V1
V1
t1
Signal
t1
LOW LINE
CEIN
CEOUT
t1 = RESET TIME
V1 = RESET VOLTAGE THRESHOLD LOW
PFO
Logic low.
CEIN
An additional comparator is provided for early warning of failure in the microprocessor’s power supply. The Power Fail Input
(PFI) is compared to an internal +1.3 V reference. The Power
CEIN is ignored. It is internally disconnected
from its internal pull-up and does not source or
sink current as long as its input voltage is between GND and VOUT. The input voltage does
not affect supply current.
CEOUT
Logic high. The open circuit voltage is equal to
VOUT.
Fail Output (PFO) goes low when the voltage at PFI is less than
1.3 V. Typically PFI is driven by an external voltage divider
which senses either the unregulated dc input to the system’s 5 V
regulator or the regulated 5 V output. The voltage divider ratio
OSC IN
OSC IN is ignored.
OSC SEL
OSC SEL is ignored.
V2 = RESET VOLTAGE THRESHOLD HIGH
HYSTERESIS = V2–V1
Figure 6. Chip Enable Timing
Power Fail Warning Comparator
REV. A
–7–
ADM8696/ADM8697–Typical Performance Curves
5
53
VCC = +5V
4.99
4.97
4.96
4.95
4.94
52
RESET ACTIVE TIME – ms
VOUT – Volts
4.98
10
20
30
40
50
60
IOUT – mA
70
80
90
51
50
100
49
20
Figure 8. VOUT vs. IOUT Normal Operation
40
60
80
TEMPERATURE – °C
100
120
Figure 11. RESET Active Time vs. Temperature
2.8
A4
2.798
100
2.796
VOUT – Volts
3.36 V
90
2.794
2.792
2.79
2.788
10
0%
2.786
150
250
350
450
550
650
IOUT – µA
750
850
950
1050
1V
Figure 9. VOUT vs. IOUT Battery Backup
1V
500ms
Figure 12. RESET Output Voltage vs. Supply Voltage
1.32
5.5
TA = +25°C
4.5
1.31
VCC – Volts
PFI INPUT THRESHOLD – V
5.0
4.0
3.5
1.30
3.0
2.5
1.29
20
40
60
80
TEMPERATURE – °C
100
2.0
120
10
100
1000
TIME DELAY – ms
10000
Figure 13. RESET Timeout Delay vs. VCC
Figure 10. PFI Input Threshold vs. Temperature
–8–
REV. A
ADM8696/ADM8697
APPLICATIONS INFORMATION
Increasing the Drive Current (ADM8696)
This circuit is not entirely foolproof and it is possible a software
fault could erroneously three-state the buffer. This would prevent the ADM869x from detecting that the microprocessor is no
longer operating correctly. In most cases, a better method is to
If the continuous output current requirements at VOUT exceeds
100 mA or if a lower VCC–VOUT voltage differential is desired,
an external PNP pass transistor may be connected in parallel
with the internal transistor. The BATT ON output (ADM8696)
can directly drive the base of the external transistor.
+7V TO +15V
INPUT
POWER
PNP
TRANSISTOR
+5V
INPUT
POWER
+5V
VCC
R1
0.1µF
VBATT
BATT
ON
VOUT
R3
ADM8696
Figure 14. Increasing the Drive Current
(
ASSUMING R4 < < R3 THEN
If a capacitor or a rechargeable battery is used for backup, the
charging resistor should be connected to VOUT since this eliminates the discharge path that would exist during power-down if
the resistor is connected to VCC.
R1
HYSTERESIS VH – VL = 5V –––
R2
VBATT
0.1µF
VOUT
ADM8696
WATCHDOG
STROBE
Figure 15. Rechargeable Battery
Adding Hysteresis to the Power Fail Comparator
WDI
ADM869x
CONTROL
INPUT
For increased noise immunity, hysteresis may be added to the
power fail comparator. Since the comparator circuit is noninverting, hysteresis can be added by connecting a resistor between the PFO output and the PFI input as shown in Figure 16. When PFO is low, resistor R3 sinks current from the
summing junction at the PFI pin. When PFO is high, the series
combination of R3 and R4 source current into the PFI summing
junction. This results in differing trip levels for the comparator.
Figure 17a. Programming the Watchdog Input
CONTROL
INPUT*
OSC SEL
D1
ADM869x
D2
OSC IN
Alternate Watchdog Input Drive Circuits
The watchdog feature can be enabled and disabled under program control by driving WDI with a three-state buffer (Figure
17a). When three-stated, the WDI input will float, thereby disabling the watchdog timer.
REV. A
)
extend the watchdog period rather than disabling the watchdog.
This may be done under program control using the circuit
shown in Figure 17b. When the control input is high, the OSC
SEL pin is low and the watchdog timeout is set by the external
capacitor. A 0.01 µF capacitor sets a watchdog timeout delay of
100 s. When the control input is low, the OSC SEL pin is
driven high, selecting the internal oscillator. The 100 ms or the
1.6 s period is chosen, depending on which diode in Figure 17b is used. With D1 inserted, the internal timeout is set at
100 ms while with D2 inserted the timeout is set at 1.6 s.
0.1µF
VCC
(
)
Figure 16. Adding Hysteresis to the Power Fail Comparator
VOUT – VBATT
R
R
)
R1
R1 (5V – 1.3V)
VL = 1.3V 1+ ––– – –––––––––––––
1.3V (R3 + R4 )
R2
Using a Rechargeable Battery for Backup (ADM8696)
I=
TO
µP NMI
ADM869x
(
RECHARGABLE
BATTERY
PFO
PFI
R2
R1
R1
VH = 1.3V 1+ ––– + –––
R3
R2
+5V
INPUT
POWER
R4
1.3V
0.1µF
VCC
BATTERY
7805
*LOW = INTERNAL TIMEOUT
HIGH = EXTERNAL TIMEOUT
Figure 17b. Programming the Watchdog Input
–9–
ADM8696/ADM8697
TYPICAL APPLICATIONS
ADM8696
Figure 18 shows the ADM8696 in a typical power monitoring,
battery backup application. VOUT powers the CMOS RAM.
Under normal operating conditions with VCC present, VOUT is
internally connected to VCC. If a power failure occurs, VCC will
decay and VOUT will be switched to VBATT, thereby maintaining
power for the CMOS RAM.
Power Fail RESET
Figure 18b shows a similar application for the ADM8696 but in
this case the PFI input monitors the unregulated input to the
7805 voltage regulator. This gives an earlier warning of an impending power failure. It is useful with processors operating at
low speeds or where there are a significant number of housekeeping tasks to be completed before the power is lost.
INPUT
POWER
The VCC power supply is also monitored by the Low Line Input, LLIN. A RESET pulse is generated when LLIN falls below
1.3 V. RESET will remain low for 50 ms after LLIN returns
above 1.3 V. This allows for a power-on reset and prevents repeated toggling of RESET if the VCC power supply is unstable.
Resistors R3 and R4 should be chosen to give the desired VCC
reset threshold.
7805
0.1µF
3V
BATTERY
R1
VBATT
A0–A15
GND
R3
The Watchdog Timer Input (WDI) monitors an I/O line from
the µP system. This line must be toggled once every 1.6 s to
verify correct software execution. Failure to toggle the line indicates that the µP system is not correctly executing its program
and may be tied up in an endless loop. If this happens, a reset
pulse is generated to initialize the processor.
VCC
CMOS RAM
ADM8696
R2
NC
OSC IN
OSC SEL
WDI
I/O LINE
PFO
NMI
RESET
µP
POWER
µP
RESET
LLIN
R4
RESET
LOW LINE
WDO
SYSTEM STATUS
INDICATORS
If the watchdog timer is not needed the WDI input should be
left floating.
The Power Fail Input, PFI, monitors the input power supply via
a resistive divider network R1 and R2. This input is intended as
an early warning power fail input. The voltage on the PFI input
is compared with a precision 1.3 V internal reference. If the input voltage drops below 1.3 V, a power fail output (PFO) signal
is generated. This warns of an impending power failure and may
be used to interrupt the processor so that the system may be
shut down in an orderly fashion. The resistors in the sensing
network are ratioed to give the desired power fail threshold voltage VT. The threshold should be set at a higher voltage than the
RESET threshold so there is sufficient time available to complete the shutdown procedure before the processor is RESET
and power is lost.
BATT VOUT
ON
PFI
Watchdog Timer
Power Fail Detector
0.1µF
VCC
Figure 18b. ADM8696 Typical Application Circuit B
This application also shows an optional external transistor that
may be used to provide in excess of 100 mA current on VOUT.
When VCC is higher than VBATT, the BATT ON output goes
low, providing 25 mA of base drive for the external PNP transistor. The maximum current available is dependent on the power
rating of the external transistor.
RAM Write Protection
The ADM8697 CEOUT line drives the Chip Select inputs of the
CMOS RAM. CEOUT follows CEIN as long as LLIN is above the
reset threshold. If LLIN falls below the reset threshold, CEOUT
goes high, independent of the logic level at CEIN. This prevents
the microprocessor from writing erroneous data into RAM during power-up, power-down, brownouts and momentary power
interruptions.
+5V
R1
R3
µP POWER
VCC
VOUT
PFI
LLIN
RESET
R2
R4
ADM8696
RESET
+
BATTERY
VBATT
GND
CMOS RAM
POWER
µP SYSTEM
µP RESET
PFO
µP NMI
WDI
I/O LINE
Figure 18a. ADM8696 Typical Application Circuit A
–10–
REV. A
ADM8696/ADM8697
OUTLINE DIMENSIONS
0.800 (20.32)
0.790 (20.07)
0.780 (19.81)
16
5.10
5.00
4.90
9
1
8
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.100 (2.54)
BSC
0.210 (5.33)
MAX
16
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
8
PIN 1
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
1.20
MAX
0.15
0.05
0.65
BSC
0.430 (10.92)
MAX
0.005 (0.13)
MIN
6.40
BSC
1
0.060 (1.52)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
9
4.50
4.40
4.30
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
0.30
0.19
COPLANARITY
0.10
0.20
0.09
SEATING
PLANE
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB
COMPLIANT TO JEDEC STANDARDS MS-001-AB
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 19. 16-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-16)
Dimensions shown in inches and (millimeters)
Figure 20. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 21. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
Rev. A | Page 11 of 13
1.27 (0.0500)
0.40 (0.0157)
032707-B
1
0.75
0.60
0.45
ADM8696/ADM8697
ORDERING GUIDE
Model1,2
ADM8696AN
ADM8696ANZ
ADM8696ARW
ADM8969ARW-REEL
ADM8696ARWZ
ADM8696ARWZ-REEL
ADM8696ARU
ADM8696ARU-REEL
ADM8697AN
ADM8697ANZ
ADM8697ARW
ADM8697ARW-REEL
ADM8697ARWZ
ADM8697ARU
ADM8697ARU-REEL
Notes
3
3
Temperature Range
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
−40°C to + 85°C
Package Description
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
Package Option
N-16
N-16
RW-16
RW-16
RW-16
RW-16
RU-16
RU-16
N-16
N-16
RW-16
RW-16
RW-16
RU-16
RU-16
1
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
3
Contact sales for availability and quotation.
2
AUTOMOTIVE PRODUCTS
The ADM8696/ADM8697 models are available with controlled manufacturing to support the quality and reliability requirements of
automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore,
designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available
for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information
and to obtain the specific Automotive Reliability reports for these models.
Rev. A | Page 12 of 13
ADM8696/ADM8697
REVISION HISTORY
6/10—Rev. 0 to Rev. A
Changes to Ordering Guide ...........................................................12
©1997-2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09139-0-6/10(A)
Rev. A | Page 13 of 13