IDT7200L IDT7201LA IDT7202LA CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9, 1,024 x 9 Integrated Device Technology, Inc. FEATURES: DESCRIPTION: • • • • • The IDT7200/7201/7202 are dual-port memories that load and empty data on a first-in/first-out basis. The devices use Full and Empty flags to prevent data overflow and underflow and expansion logic to allow for unlimited expansion capability in both word size and depth. The reads and writes are internally sequential through the use of ring pointers, with no address information required to load and unload data. Data is toggled in and out of the devices through the use of the Write (W) and Read (R) pins. The devices utilize a 9-bit wide data array to allow for control and parity bits at the user’s option. This feature is especially useful in data communications applications where it is necessary to use a parity bit for transmission/reception error checking. It also features a Retransmit (RT) capability that allows for reset of the read pointer to its initial position when RT is pulsed low to allow for retransmission from the beginning of data. A Half-Full Flag is available in the single device mode and width expansion modes. These FIFOs are fabricated using IDT’s high-speed CMOS technology. They are designed for those applications requiring asynchronous and simultaneous read/writes in multiprocessing and rate buffer applications. Military grade product is manufactured in compliance with the latest revision of MILSTD-883, Class B. • • • • • • • • • • First-In/First-Out dual-port memory 256 x 9 organization (IDT7200) 512 x 9 organization (IDT7201) 1,024 x 9 organization (IDT7202) Low power consumption — Active: 770mW (max.) —Power-down: 2.75mW (max.) Ultra high speed—12ns access time Asynchronous and simultaneous read and write Fully expandable by both word depth and/or bit width Pin and functionally compatible with 720X family Status Flags: Empty, Half-Full, Full Auto-retransmit capability High-performance CEMOS technology Military product compliant to MIL-STD-883, Class B Standard Military Drawing #5962-87531, 5962-89666, 5962-89863 and 5962-89536 are listed on this function Industrial temperature range (–40°C to +85°C) is available (plastic packages only) FUNCTIONAL BLOCK DIAGRAM DATA INPUTS (D 0 –D 8) W WRITE CONTROL WRITE POINTER R READ CONTROL THREESTATE BUFFERS DATA OUTPUTS (Q 0 –Q 8 ) FLAG LOGIC EXPANSION LOGIC XI RAM ARRAY 256 x 9 512 x 9 1,024 x 9 EF FF READ POINTER RS RESET LOGIC FL/RT XO/HF 2679 drw 01 The IDT logo is a trademark of Integrated Device Technology, Inc. MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES 1997 Integrated Device Technology, Inc. For latest information contact IDT's web site at www.idt.com or fax-on-demand at 408-492-8391. SEPTEMBER 1997 DSC-2679/7 1 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 W 1 28 VCC D8 2 27 D4 4 3 2 1 32 31 30 D3 3 26 D5 D2 D1 4 5 25 24 D6 D7 D0 6 23 XI FF 7 22 Q0 8 9 21 20 FL/RT RS EF XO/HF Q1 10 19 Q7 Q2 11 18 Q6 Q3 12 17 Q5 Q8 GND 13 14 16 15 Q4 D2 5 29 D6 D1 D0 XI FF 6 7 8 9 28 27 26 25 D7 NC FL/RT Q0 Q1 NC Q2 10 11 12 13 24 23 22 21 RS EF XO/HF Q7 Q6 Reference Identifier P28-1 P28-2 D28-1 D28-3 SO28-3 E28-2 Order Code P TP D TD SO XE LCC(1) PLCC R Q4 Q5 R GND NC Q3 Q8 14 15 16 17 18 19 20 2679 drw 02a PLASTIC DIP(1) PLASTIC THIN DIP CERDIP(1) THIN CERDIP SOIC CERPAK(1) D5 D3 D8 INDEX NC VCC D4 PIN CONFIGURATIONS W MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES Reference Identifier L32- 1 J32-1 2679 drw 02b Order Code L J TOP VIEW TOP VIEW NOTE: 1. The 600-mil-wide DIP (P28-1 and D28-1), CERPACK and LCC are not available for the 7200. RECOMMENDED OPERATING CONDITIONS ABSOLUTE MAXIMUM RATINGS Symbol Rating VTERM Terminal Voltage with Respect to GND TSTG Storage Temperature IOUT DC Output Current Com’l & Ind'l –0.5 to +7.0 Mil. Unit –0.5 to +7.0 V –55 to +125 –65 to +155 °C –50 to +50 –50 to +50 mA NOTE: 2679 tbl 01 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliabilty. CAPACITANCE (TA = +25°C, f = 1.0 MHz) Symbol CIN COUT Parameter(1) Input Capacitance Output Capacitance Condition VIN = 0V VOUT = 0V NOTE: 1. This parameter is sampled and not 100% tested. Max. 8 8 Unit pF pF 2679 tbl 02 Symbol Min. Typ. VCCM Military Supply Voltage Parameter 4.5 5.0 Max. Unit 5.5 V VCCC Commercial Supply Voltage 4.5 5.0 5.5 V GND Supply Voltage 0 0 0 V (1) VIH Input High Voltage Commercial 2.0 — — V VIH(1) Input High Voltage Military 2.2 — — V VIL(2) Input Low Voltage Commercial and Military — — 0.8 V TA Operating Temperature Commercial 0 — 70 °C TA Operating Temperature Industrial –40 — 85 °C TA Operating Temperature Military –55 — 125 °C NOTES: 1. VIH = 2.6V for XI input (commercial). VIH = 2.8V for XI input (military). 2. 1.5V undershoots are allowed for 10ns once per cycle. 2679 tbl 03 2 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C; Industrial: VCC = 5V ± 10%, TA = –40°C to +85°C; Military: VCC = 5V ± 10%, TA = –55°C to +125°C) IDT7200L IDT7201LA IDT7202LA Com'l & Ind'l(1) tA = 12, 15, 20, 25, 35 ns Symbol Parameter Min. Typ. IDT7200L IDT7201LA IDT7202LA Military tA = 20, 30, 40 ns Max. Min. Typ. Max. Unit Input Leakage Current (Any Input) –1 — 1 –10 — 10 µA ILO(3) Output Leakage Current –10 — 10 –10 — 10 µA VOH Output Logic “1” Voltage IOH = –2mA 2.4 — — 2.4 — — V VOL Output Logic “0” Voltage IOL = 8mA — — 0.4 — — 0.4 V ICC1(4,5,6) Active Power Supply Current — — 125 — — 140 mA ICC2(4,6,7) Standby Current (R=W=RS=FL/RT=VIH) — — 15 — — 20 mA Power Down Current — — 0.5 — — 0.9 ILI (2) ICC3(L) (4,6,7) mA 2679 tbl 04 IDT7200L IDT7201LA IDT7202LA Commercial tA = 50 ns Symbol Parameter IDT7200L IDT7201LA IDT7202LA Military tA = 50, 65, 80, 120 ns Min. Typ. Max. Min. Typ. Max. Unit ILI(2) Input Leakage Current (Any Input) –1 — 1 –10 — 10 µA ILO(3) Output Leakage Current –10 — 10 –10 — 10 µA VOH Output Logic “1” Voltage IOH = –2mA 2.4 — — 2.4 — — V VOL Output Logic “0” Voltage IOL = 8mA — — 0.4 — — 0.4 V ICC1(4,5,6) Active Power Supply Current — 50 80 — 70 100 mA ICC2(4,6,7) Standby Current (R=W=RS=FL/RT=VIH) — 5 8 — 8 15 mA ICC3(L)(4,6,7) Power Down Current — — 0.5 — — 0.9 mA NOTES: 2679 tbl 05 1. Industrial temperature range product for the 25 ns speed grade is available as a standard device. All other speed grades are available by special order. 2. Measurements with 0.4 ≤ VIN ≤ VCC. 3. R ≥ VIH, 0.4 ≤ VOUT ≤ VCC. 4. Tested with outputs open (IOUT = 0). 5. RCLK and WCLK toggle at 20 MHz and data inputs switch at 10 MHz. 6. ICC measurements are made with outputs open. 7. All Inputs = VCC - 0.2V or GND + 0.2V, except RCLK and WCLK, which toggle at 20 MHz. AC TEST CONDITIONS Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels Output Load GND to 3.0V 5ns 1.5V 1.5V See Figure 1 2679 tbl 08 3 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS(1) (Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C; Industrial: VCC = 5V ± 10%, TA = –40°C to +85°C; Military: VCC = 5V ± 10%, TA = –55°C to +125°C) Com'l & Mil. Com'l & Ind'l(2) Commercial 7200L12 7200L15 7201LA12 7201LA15 7202LA12 7202LA15 Symbol Parameter 7200L20 7201LA20 7202LA20 Min. Max. Min. Max. Min. Max. 7200L25 7201LA25 7202LA25 Military Com'l 7200L30 7200L35 7201LA30 7201LA35 7202LA30 7202LA35 Min. Max. Min. Max. Min. Max. Unit tS Shift Frequency — 50 — 40 — 33.3 — 28.5 — 25 — tRC Read Cycle Time 20 — 25 — 30 — 35 — 40 — 45 — ns tA Access Time — 12 — 15 — 20 — 25 — 30 — 35 ns tRR Read Recovery Time 8 — 10 — 10 — 10 — 10 — 10 — ns tRPW Read Pulse Width(3) 12 — 15 — 20 — 25 — 30 — 35 — ns tRLZ Read Pulse Low to Data Bus at Low Z(4) 3 — 5 — 5 — 5 — 5 — 5 — ns tWLZ Write Pulse High to Data Bus at Low Z(4,5) 3 — 5 — 5 — 5 — 5 — 10 — ns tDV Data Valid from Read Pulse High 5 — 5 — 5 — 5 — 5 — 5 — ns (4) 22.2 MHz tRHZ Read Pulse High to Data Bus at High Z — 12 — 15 — 15 — 18 — 20 — 20 ns tWC Write Cycle Time 20 — 25 — 30 — 35 — 40 — 45 — ns 12 — 15 — 20 — 25 — 30 — 35 — ns (3) tWPW Write Pulse Width tWR Write Recovery Time 8 — 10 — 10 — 10 — 10 — 10 — ns tDS Data Set-up Time 9 — 11 — 12 — 15 — 18 — 18 — ns tDH Data Hold Time 0 — 0 — 0 — 0 — 0 — 0 — ns tRSC Reset Cycle Time 20 — 25 — 30 — 35 — 40 — 45 — ns tRS Reset Pulse Width(3) 12 — 15 — 20 — 25 — 30 — 35 — ns tRSS Reset Set-up Time(4) 12 — 15 — 20 — 25 — 30 — 35 — ns tRSR Reset Recovery Time 8 — 10 — 10 — 10 — 10 — 10 — ns tRTC Retransmit Cycle Time 20 — 25 — 30 — 35 — 40 — 45 — ns tRT (3) Retransmit Pulse Width 12 — 15 — 20 — 25 — 30 — 35 — ns tRTS Retransmit Set-up Time(4) 12 — 15 — 20 — 25 — 30 — 35 — ns tRTR Retransmit Recovery Time 8 — 10 — 10 — 10 — 10 — 10 — ns tEFL Reset to Empty Flag Low — 12 — 25 — 30 — 35 — 40 — 45 ns tHFH,FFH Reset to Half-Full and Full Flag High — 17 — 25 — 30 — 35 — 40 — 45 ns tRTF Retransmit Low to Flags Valid — 20 — 25 — 30 — 35 — 40 — 45 ns tREF Read Low to Empty Flag Low — 12 — 15 — 20 — 25 — 30 — 30 ns tRFF Read High to Full Flag High — 14 — 15 — 20 — 25 — 30 — 30 ns tRPE Read Pulse Width after EF High 12 — 15 — 20 — 25 — 30 — 35 — ns tWEF Write High to Empty Flag High — 12 — 15 — 20 — 25 — 30 — 30 ns tWFF Write Low to Full Flag Low — 14 — 15 — 20 — 25 — 30 — 30 ns tWHF Write Low to Half-Full Flag Low — 17 — 25 — 30 — 35 — 40 — 45 ns tRHF Read High to Half-Full Flag High — 17 — 25 — 30 — 35 — 40 — 45 ns tWPF Write Pulse Width after FF High 12 — 15 — 20 — 25 — 30 — 35 — ns tXOL Read/Write to XO Low — 12 — 15 — 20 — 25 — 30 — 35 ns tXOH Read/Write to XO High — 12 — 15 — 20 — 25 — 30 — 35 ns tXI XI Pulse Width XI Recovery Time XI Set-up Time 12 — 15 — 20 — 25 — 30 — 35 — ns 8 — 10 — 10 — 10 — 10 — 10 — ns 8 — 10 — 10 — 10 — 10 — 10 — tXIR tXIS (3) NOTES: 1. Timings referenced as in AC Test Conditions. 2. Industrial temperature range is available by special order for speed grades faster than 25ns. ns 2679 tbl 06 3. Pulse widths less than minimum value are not allowed. 4. Values guaranteed by design, not currently tested. 5. Only applies to read data flow-through mode. 4 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS(1) (Continued) (Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C; Industrial: VCC = 5V ± 10%, TA = –40°C to +85°C; Military: VCC = 5V ± 10%, TA = –55°C to +125°C) Symbol Com'l & Mil. 7200 L40 7201LA40 7202LA40 7200L50 7201LA50 7202LA50 Min. 7200L65 7201LA65 7202LA65 7200L80 7201LA80 7202LA80 7200L120 7201LA120 7202LA120 Max. Min. Max. Min. Max. Min. Max. Unit Shift Frequency — 20 — 15 — 12.5 — 10 — 7 MHz tRC Read Cycle Time 50 — 65 — 80 — 100 — 140 — ns tA Access Time — 40 — 50 — 65 — 80 — 120 ns tRR Read Recovery Time 10 — 15 — 15 — 20 — 20 — ns 40 — 50 — 65 — 80 — 120 — ns (3) Read Pulse Width (4) Max. Min. Military(2) tS tRPW Parameter Military tRLZ Read Pulse Low to Data Bus at Low Z 5 — 10 — 10 — 10 — 10 — ns tWLZ Write Pulse High to Data Bus at Low Z(4, 5) 10 — 15 — 15 — 20 — 20 — ns tDV Data Valid from Read Pulse High 5 — 5 — 5 — 5 — 5 — ns (4) tRHZ Read Pulse High to Data Bus at High Z — 25 — 30 — 30 — 30 — 35 ns tWC Write Cycle Time 50 — 65 — 80 — 100 — 140 — ns (3) tWPW Write Pulse Width 40 — 50 — 65 — 80 — 120 — ns tWR Write Recovery Time 10 — 15 — 15 — 20 — 20 — ns tDS Data Set-up Time 20 — 30 — 30 — 40 — 40 — ns tDH Data Hold Time 0 — 5 — 10 — 10 — 10 — ns tRSC Reset Cycle Time 50 — 65 — 80 — 100 — 140 — ns tRS Reset Pulse Width(3) 40 — 50 — 65 — 80 — 120 — ns (4) tRSS Reset Set-up Time 40 — 50 — 65 — 80 — 120 — ns tRSR Reset Recovery Time 10 — 15 — 15 — 20 — 20 — ns tRTC Retransmit Cycle Time 50 — 65 — 80 — 100 — 140 — ns tRT (3) Retransmit Pulse Width 40 — 50 — 65 — 80 — 120 — ns tRTS Retransmit Set-up Time(4) 40 — 50 — 65 — 80 — 120 — ns tRTR Retransmit Recovery Time 10 — 15 — 15 — 20 — 20 — ns tEFL Reset to Empty Flag Low — 50 — 65 — 80 — 100 — 140 ns tHFH,FFH Reset to Half-Full and Full Flag High — 50 — 65 — 80 — 100 — 140 ns tRTF Retransmit Low to Flags Valid — 50 — 65 — 80 — 100 — 140 ns tREF Read Low to Empty Flag Low — 30 — 45 — 60 — 60 — 60 ns tRFF Read High to Full Flag High — 35 — 45 — 60 — 60 — 60 ns tRPE Read Pulse Width after EF High 40 — 50 — 65 — 80 — 120 — ns tWEF Write High to Empty Flag High — 35 — 45 — 60 — 60 — 60 ns tWFF Write Low to Full Flag Low — 35 — 45 — 60 — 60 — 60 ns tWHF Write Low to Half-Full Flag Low — 50 — 65 — 80 — 100 — 140 ns tRHF Read High to Half-Full Flag High — 50 — 65 — 80 — 100 — 140 ns tWPF Write Pulse Width after FF High 40 — 50 — 65 — 80 — 120 — ns tXOL Read/Write to XO Low — 40 — 50 — 65 — 80 — 120 ns tXOH Read/Write to XO High — 40 — 50 — 65 — 80 — 120 ns tXI XI Pulse Width XI Recovery Time XI Set-up Time 40 — 50 — 65 — 80 — 120 — ns tXIR tXIS (3) 10 — 10 — 10 — 10 — 10 — ns 10 — 15 — 15 — 15 — 15 — ns NOTES: 1. Timings referenced as in AC Test Conditions 2. Speed grades 65, 80 and 120 not available in the CERPACK 3. Pulse widths less than minimum value are not allowed. 2679 tbl 07 4. Values guaranteed by design, not currently tested. 5. Only applies to read data flow-through mode. 5 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 5V 1.1K TO OUTPUT PIN 680Ω 30pF* 2679 drw 03 or equivalent circuit Figure 1. Output Load * Includes scope and jig capacitances. SIGNAL DESCRIPTIONS INPUTS: DATA IN (D0 – D8) Data inputs for 9-bit wide data. CONTROLS: RESET (RS) Reset is accomplished whenever the Reset (RS) input is taken to a low state. During reset, both internal read and write pointers are set to the first location. A reset is required after power up before a write operation can take place. Both the Read Enable (R) and Write Enable (W) inputs must be in the high state during the window shown in Figure 2, (i.e., tRSS before the rising edge of RS) and should not change until tRSR after the rising edge of RS. Half-Full Flag (HF) will be reset to high after Reset (RS). WRITE ENABLE (W) A write cycle is initiated on the falling edge of this input if the Full Flag (FF) is not set. Data set-up and hold times must be adhered to with respect to the rising edge of the Write Enable (W). Data is stored in the RAM array sequentially and independently of any on-going read operation. After half of the memory is filled and at the falling edge of the next write operation, the Half-Full Flag (HF) will be set to low and will remain set until the difference between the write pointer and read pointer is less than or equal to one half of the total memory of the device. The Half-Full Flag (HF) is then reset by the rising edge of the read operation. To prevent data overflow, the Full Flag (FF) will go low, inhibiting further write operations. Upon the completion of a valid read operation, the Full Flag (FF) will go high after tRFF, allowing a valid write to begin. When the FIFO is full, the internal write pointer is blocked from W, so external changes in W will not affect the FIFO when it is full. READ ENABLE (R) A read cycle is initiated on the falling edge of the Read Enable (R) provided the Empty Flag (EF) is not set. The data is accessed on a First-In/First-Out basis, independent of any MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES ongoing write operations. After Read Enable (R) goes high, the Data Outputs (Q0 – Q8) will return to a high impedance condition until the next Read operation. When all data has been read from the FIFO, the Empty Flag (EF) will go low, allowing the “final” read cycle but inhibiting further read operations with the data outputs remaining in a high impedance state. Once a valid write operation has been accomplished, the Empty Flag (EF) will go high after tWEF and a valid Read can then begin. When the FIFO is empty, the internal read pointer is blocked from R so external changes in R will not affect the FIFO when it is empty. FIRST LOAD/RETRANSMIT (FL/RT) This is a dual-purpose input. In the Depth Expansion Mode, this pin is grounded to indicate that it is the first loaded (see Operating Modes). In the Single Device Mode, this pin acts as the restransmit input. The Single Device Mode is initiated by grounding the Expansion In (XI). The IDT7200/7201A/7202A can be made to retransmit data when the Retransmit Enable control (RT) input is pulsed low. A retransmit operation will set the internal read pointer to the first location and will not affect the write pointer. Read Enable (R) and Write Enable (W) must be in the high state during retransmit. This feature is useful when less than 256/ 512/1,024 writes are performed between resets. The retransmit feature is not compatible with the Depth Expansion Mode and will affect the Half-Full Flag (HF), depending on the relative locations of the read and write pointers. EXPANSION IN (XI) This input is a dual-purpose pin. Expansion In (XI) is grounded to indicate an operation in the single device mode. Expansion In (XI) is connected to Expansion Out (XO) of the previous device in the Depth Expansion or Daisy Chain Mode. OUTPUTS: FULL FLAG (FF) The Full Flag (FF) will go low, inhibiting further write operation, when the write pointer is one location less than the read pointer, indicating that the device is full. If the read pointer is not moved after Reset (RS), the Full-Flag (FF) will go low after 256 writes for IDT7200, 512 writes for the IDT7201A and 1,024 writes for the IDT7202A. EMPTY FLAG (EF) The Empty Flag (EF) will go low, inhibiting further read operations, when the read pointer is equal to the write pointer, indicating that the device is empty. EXPANSION OUT/HALF-FULL FLAG (XO/HF) This is a dual-purpose output. In the single device mode, when Expansion In (XI) is grounded, this output acts as an indication of a half-full memory. After half of the memory is filled and at the falling edge of the next write operation, the Half-Full Flag (HF) will be set low and will remain set until the difference between the write 6 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES pointer and read pointer is less than or equal to one half of the total memory of the device. The Half-Full Flag (HF) is then reset by using rising edge of the read operation. In the Depth Expansion Mode, Expansion In (XI) is connected to Expansion Out (XO) of the previous device. This output acts as a signal to the next device in the Daisy Chain by providing a pulse to the next device when the previous device reaches the last location of memory. DATA OUTPUTS (Q0 – Q8) Data outputs for 9-bit wide data. This data is in a high impedance condition whenever Read (R) is in a high state. t RSC t RS RS t RSS t RSR W t RSS R t EFL EF t HFH , t FFH HF, FF 2679 drw 04 NOTES: 1. EF, FF, HF may change status during Reset, but flags will be valid at tRSC. 2. W and R = VIH around the rising edge of RS. Figure 2. Reset t t RPW RC t RR tA tA R t RLZ t DV Q0 – Q8 t RHZ DATA OUT VALID t WPW t WC DATA OUT VALID t WR W t DS D0 – D8 t DH DATA IN VALID DATA IN VALID 2679 drw 05 Figure 3. Asynchronous Write and Read Operation LAST WRITE IGNORED WRITE FIRST READ ADDITIONAL READS FIRST WRITE R W t WFF t RFF FF 2679 drw 06 Figure 4. Full Flag From Last Write to First Read 7 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 LAST READ IGNORED READ MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES FIRST WRITE ADDITIONAL WRITES FIRST READ W R t WEF t REF EF tA DATA OUT VALID VALID 2679 drw 07 Figure 5. Empty Flag From Last Read to First Write t RTC t RT RT t RTR t RTS W,R t RTF HF, EF, FF FLAG VALID 2679 drw 08 Figure 6. Retransmit W t WEF EF t RPE R 2679 drw 09 Figure 7. Minimum Timing for an Empty Flag Coincident Read Pulse R t RFF FF t WPF W 2679 drw 10 Figure 8. Minimum Timing for an Full Flag Coincident Write Pulse 8 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES W t RHF R t WHF HF HALF-FULL OR LESS HALF-FULL OR LESS MORE THAN HALF-FULL 2679 drw 11 Figure 9. Half-Full Flag Timing WRITE TO LAST PHYSICAL LOCATION READ FROM LAST PHYSICAL LOCATION W R t XOL t XOH t XOL t XOH 2679 drw 12 XO Figure 10. Expansion Out t XI t XIR XI W t XIS WRITE TO FIRST PHYSICAL LOCATION t XIS READ FROM FIRST PHYSICAL LOCATION R 2679 drw 13 Figure 11. Expansion In OPERATING MODES: Care must be taken to assure that the appropriate flag is monitored by each system (i.e. FF is monitored on the device where W is used; EF is monitored on the device where R is used). For additional information, refer to Tech Note 8: Operating FIFOs on Full and Empty Boundary Conditions and Tech Note 6: Designing with FIFOs. Single Device Mode A single IDT7200/7201A/7202A may be used when the application requirements are for 256/512/1,024 words or less. These devices are in a Single Device Configuration when the Expansion In (XI) control input is grounded (see Figure 12). Depth Expansion The IDT7200/7201A/7202A can easily be adapted to applications when the requirements are for greater than 256/512/ 1,024 words. Figure 14 demonstrates Depth Expansion using three IDT7200/7201A/7202As. Any depth can be attained by adding additional IDT7200/7201A/7202As. These FIFOs operate in the Depth Expansion mode when the following conditions are met: 1. The first device must be designated by grounding the First Load (FL) control input. 2. All other devices must have FL in the high state. 3. The Expansion Out (XO) pin of each device must be tied to the Expansion In (XI) pin of the next device. See Figure 14. 4. External logic is needed to generate a composite Full Flag (FF) and Empty Flag (EF). This requires the ORing of all EFs and ORing of all FFs (i.e. all must be set to generate the correct composite FF or EF). See Figure 14. 5. The Retransmit (RT) function and Half-Full Flag (HF) are not available in the Depth Expansion Mode. For additional information, refer to Tech Note 9: Cascading FIFOs or FIFO Modules. 9 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES USAGE MODES: Width Expansion Word width may be increased simply by connecting the corresponding input control signals of multiple devices. Status flags (EF, FF and HF) can be detected from any one device. Figure 13 demonstrates an 18-bit word width by using two IDT7200/7201A/7202As. Any word width can be attained by adding additional IDT7200/7201A/7202As (Figure 13). Bidirectional Operation Applications which require data buffering between two systems (each system capable of Read and Write operations) can be achieved by pairing IDT7200/7201A/7202As as shown in Figure 16. Both Depth Expansion and Width Expansion may be used in this mode. Data Flow-Through Two types of flow-through modes are permitted, a read flow-through and write flow-through mode. For the read flowthrough mode (Figure 17), the FIFO permits a reading of a single word after writing one word of data into an empty FIFO. The data is enabled on the bus in (tWEF + tA) ns after the rising edge of W, called the first write edge, and it remains on the bus until the R line is raised from low-to-high, after which the bus would go into a three-state mode after tRHZ ns. The EF line would have a pulse showing temporary deassertion and then would be asserted. In the write flow-through mode (Figure 18), the FIFO permits the writing of a single word of data immediately after reading one word of data from a full FIFO. The R line causes the FF to be deasserted but the W line being low causes it to be asserted again in anticipation of a new data word. On the rising edge of W, the new word is loaded in the FIFO. The W line must be toggled when FF is not asserted to write new data in the FIFO and to increment the write pointer. Compound Expansion The two expansion techniques described above can be applied together in a straightforward manner to achieve large FIFO arrays (see Figure 15). (HF) (HALF–FULL FLAG) WRITE (W) READ (R) 9 9 IDT 7200/ 7201A/ 7202A DATA IN (D) FULL FLAG (FF) RESET (RS) DATA OUT (Q) EMPTY FLAG (EF) RETRANSMIT (RT) EXPANSION IN (XI) 2679 drw 14 Figure 12. Block Diagram of Single 256 x 9, 512 x 9, 1,024 x 9 FIFO HF 18 HF 9 9 DATA IN (D) WRITE (W) FULL FLAG (FF) RESET (RS) IDT 7200/ 7201A/ 7202A 9 XI READ (R) IDT 7200/ 7201A/ 7202A EMPTY FLAG (EF) RETRANSMIT (RT) 9 XI 18 DATA OUT (Q) 2679 drw 15 Figure 13. Block Diagram of 256 x 18, 512 x 18, 1,024 x 18 FIFO Memory Used in Width Expansion Mode 10 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES TABLE I—RESET AND RETRANSMIT Single Device Configuration/Width Expansion Mode Inputs Mode Reset Retransmit Read/Write RS RT XI 0 1 X 0 0 0 Internal Status Read Pointer Write Pointer Location Zero Location Zero Location Zero Unchanged 1 1 0 Increment(1) Increment(1) Outputs EF FF HF 0 X 1 X 1 X X X X NOTE: 1. Pointer will increment if flag is High. 2679 tbl 09 TABLE II—RESET AND FIRST LOAD TRUTH TABLE Depth Expansion/Compound Expansion Mode Inputs Mode Reset First Device Reset All Other Devices Read/Write RS FL XI 0 0 0 1 (1) (1) 1 X (1) NOTE: 1. XI is connected to XO of previous device. See Figure 14. XI = Expansion Input, HF = Half-Full Flag Output Internal Status Read Pointer Write Pointer Location Zero Location Zero Location Zero Location Zero X X Outputs EF FF 0 0 1 1 X X 2679 tbl 10 RS = Reset Input, FL/RT = First Load/Retransmit, EF = Empty Flag Output, FF = Flag Full Output, XO W D FF 9 9 IDT 7200/ 7201A/ 7202A R EF 9 FL XI Q VCC XO FF FULL 9 IDT 7200/ 7201A/ 7202A EF EMPTY FL XI XO FF 9 RS IDT 7200/ 7201A/ 7202A XI EF FL 2679 drw 16 Figure 14. Block Diagram of 768 x 9, 1,536 x 9, 3,072 x 9 FIFO Memory (Depth Expansion) 11 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES Q 0 –Q 8 Q 9 –Q 17 Q (N-8) -Q N ••• Q 0 –Q 8 R, W, RS Q 9 –Q 17 IDT7200/ IDT7201A/ IDT7202A DEPTH EXPANSION BLOCK Q (N-8) -Q N IDT7200/ IDT7201A/ IDT7202A DEPTH EXPANSION BLOCK D 0 -D 8 IDT7200/ IDT7201A/ IDT7202A DEPTH EXPANSION BLOCK ••• D 9 -D 17 D (N-8) -D N D 0 –D N ••• D 9 -D N D 18 -D N D (N-8) -D N 2679 drw 17 NOTES: 1. For depth expsansion block see section on Depth Expansion and Figure 14. 2. For Flag detection see section on Width Expansion and Figure 13. Figure 15. Compound FIFO Expansion WA FFA RB EF B HF B IDT 7200/ IDT 7201A/ 7201A 7202A DA 0-8 Q B 0-8 SYSTEM A SYSTEM B Q A 0-8 RA HF A EF A D B 0-8 IDT 7200/ 7201A/ 7202A WB FFB 2679 drw 18 Figure 16. Bidirectional FIFO Mode DATA IN W t RPE R EF t WLZ t WEF tA t REF DATA OUT DATA OUT VALID 2679 drw 19 Figure 17. Read Data Flow-Through Mode 12 IDT7200/7201A/7202A CMOS ASYNCHRONOUS FIFO 256 x 9, 512 x 9 and 1,024 x 9 MILITARY, INDUSTRIAL AND COMMERCIAL TEMPERATURE RANGES R t W WPF t RFF FF t DH t WFF DATA DATA IN t IN VALID t DS A DATA OUT DATA OUT VALID 2679 drw 20 Figure 18. Write Data Flow-Through Mode ORDERING INFORMATION IDT XXXX X XXX X X Device Type Power Speed Package Process/ Temperature Range Blank I (1) B Commercial (0°C to +70°C) Industrial (–40°C to +85°C) Military (–55°C to +125°C) Compliant to MIL-STD-883, Class B P TP D TD J SO L XE Plastic DIP Plastic Thin DIP CERDIP Thin CERDIP Plastic Leaded Chip Carrier PLCC SOIC LCC Leadless Chip Carrier CERPACK 12 15 20 25 30 35 40 50 65 80 120 Commercial Only Commercial Only (2) Commercial and Industrial Military Only Commercial Only Military Only P28-1 P28-2 D28-1 D28-3 J32-1 SO28-3 L32-1 E28-2 (7201 & 7202 Only) (7201 & 7202 Only) (7201 & 7202 Only) (7201 & 7202 Only) Access Time (t A) Speed in Nanoseconds Military only-except XE package LA Low Power 7200 7201 7202 256 x 9-Bit FIFO 512 x 9-Bit FIFO 1,024 x 9-Bit FIFO 2679 drw 21 NOTES: 1. Industrial temperature range is available for plastic packages by special order for speed grades faster than 25 ns. 2. "A" to be included for 7201 and 7202 ordering part number. 13