Nel HK-A290A-FREQ Differential positive ecl (dpecl) Datasheet

CRYSTAL CLOCK OSCILLATORS
Data Sheet 9235A
Rev. N
Differential Positive ECL (DPECL)
HK-2900 Series
Description
The HK-2900 Series of quartz crystal oscillators provide DPECL Fast Edge compatible signals. This
device is to operate using positive voltage and uses multiple ground pins for improved signal integrity. This
device is intended to operate on positive voltage for PECL applications.
Features
• Wide frequency range–250.0MHz to 500.0MHz
• User specified tolerance available
• Case at electrical ground
• Will withstand vapor phase temperatures of 253°C
for 4 minutes maximum
• All metal, resistance weld, hermetically sealed
package
• High shock resistance, to 1500g
• Low Jitter
• Overtone technology
• High Q Crystal actively tuned oscillator circuit
• Power supply decoupling internal
• Dual ground plane for added stability
• No internal PLL avoids cascading PLL problems
• High frequencies due to proprietary design
• RoHS Compliant, Lead Free Construction
Electrical Connection
Pin
Connection
1
2
6
7
8
9
13
14
VCC
VEE Case
VEE Case
Output
/Output
VEE Case
VEE Case
Enable/Disable
All dimensions expressed in Inches/MM
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Data Sheet 9235A
CRYSTAL CLOCK OSCILLATORS
Rev. N
HK-2900 Series Continued
Differential Positive ECL (DPECL)
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Frequency
Duty Cycle
Logic 0 (2)
Logic 1(2)
Rise & Fall Time
Jitter, RMS(3)
Enable Voltage(4)
Disable Voltage
Frequency Stability (1)
Symbol
Conditions
Min
--------250.0MHz
----@ 50% points
45/55%
VOL
----VCC-1.95V
VOH
----VCC-1.02V
tr,tf 20-80%VO with 50 ohm load to VCC-2V -------------------with VEE=0V
0V
3.0V
----with VEE=0V
dF/F
Overall conditions including:
-100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
Typical
----------------350 psec
-----------------
Max
500.0MHz
55/45%
VCC-1.60V
VCC-0.74V
600 psec
5 psec
1.0V
VCC
+100ppm
Typical
5.0V
-----
Max
5.25V
120 mA
-------------
±50.0 mA
70°C
125°C
-----
300°C
2 ms
10 ms
General Characteristics
Parameter
Supply Voltage
Supply Current
Symbol
VCC
ICC
Conditions
----50 ohm termination
To 2.00V below VCC
Low level Output Current
----------
Min
4.75V
0.0 mA
Output current
IO
0.0 mA
0°C
Operating temperature
TA
-55°C
Storage temperature
TS
Input: Logic High (ECL) - Disables
VEE or Open - Enables
Soldering, 10 sec.
----Lead temperature
TL
Load
50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required
--------Start-up time
tS
Environmental and Mechanical Characteristics
Mechanical Shock
Thermal Shock
Vibration
Soldering Condition
Hermetic Seal
Per MIL-STD-202, Method 213, Condition E
Per MIL-STD-833, Method 1011, Condition A
0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
300°C for 10 seconds
Leak rate less than 1 x 10 -8 atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) VOL, VOH, referenced to ground
3) Jitter performance is frequency dependent. Please contact factory for full characterization.
RMS jitter bandwidth of 12kHz to 20MHz.
4) Open to Enable pin also enables to output.
Creating a Part Number
HK - A290X - FREQ
Package Code
HK Leaded 8 pin (14pin)
SK 8 pin (14 pin) SMD Gull
Wing
Input Voltage
Code Specification
A
3.3V
5V
Tolerance/Performance
0 ±100ppm 0-70°C
1 ±50ppm 0-70°C
7 ±25ppm 0-70°C
9 Customer Specific
A ±20ppm 0-70°C
B ±50ppm -40 to +85°C
C ±100ppm -40 to +85°C
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Similar pages