Data Sheet No. PD60285 IR3315(S)PbF LOW EMI CURRENT SENSE HIGH SIDE SWITCH Features • • • • • • • • Product Summary Rds(on) 20 mΩ max. Vcc op. 6 to 32V Current Ratio 2800 Prog. Ishutdown 3 to 30A Vclamp 40V Load current feedback Programmable over current shutdown Active clamp ESD protection Input referenced to Vcc Over temperature shutdown Reverse battery protection Lead-Free Packages Description The IR3315(S)PbF is a fully protected 4 terminals high side switch. The input signal is referenced to Vcc. When the input voltage Vcc - Vin is higher than the specified threshold, the output power Mosfet is turned on. When the Vcc - Vin is lower than the specified Vil threshold, the output Mosfet is turned off. A current proportional to the power Mosfet current is sourced to the Ifb pin. Over current shutdown occurs when Vst-Vin > 4.5V. The current shutdown threshold is adjusted by selecting the proper RIfb. Either over current and over temperature latches off the switch. The device is reset by pulling the input pin high. Other integrated protections (ESD, reverse battery, active clamp) make the switch very rugged in automotive environment. TO-220 IR3315PbF D²Pak Pin 4 and 5 fused IR3315SPbF Typical Connection Vcc IR3315 IN Battery Current feeback Input On Off www.irf.com 10k Ifb Out Load Rifb Logic Ground Power Ground 1 IR3315(S)PbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Vcc lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Vcc-Vin Maximum Vcc voltage Vcc-Vin cont. Maximum continuous Vcc voltage Vcc-Vfb Maximum Ifb voltage Vcc-Vout Maximum output voltage Ids cont. Maximum body diode continuous current Rth=60°C/W (1) Ids pulsed Maximum body diode pulsed current (1) Pd Maximum power dissipation Rth=60°C/W ESD1 Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω ESD2 Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω Tj max. Max. storage & operating temperature junction temperature Min Rfb Minimum on the resistor on Ifb pin Ifb max. Max. Ifb current (1) Limited by junction temperature. Pulsed is also limited by wiring Min. Max. -16 -16 -16 -0.3 37 32 33 37 2.8 100 2 4 0.5 150 ⎯ ⎯ ⎯ ⎯ ⎯ -40 0.3 -50 Units V A W kV 50 °C kΩ mA Typ. Max. Units 60 1.6 1.6 ⎯ ⎯ ⎯ °C/W ⎯ Thermal Characteristics Symbol Parameter Rth1 Rth2 Rth3 Thermal resistance junction to ambient D²-Pak Std footprint Thermal resistance junction to case D²-Pak Thermal resistance junction to case TO-220 Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Parameter Continuous output current Tambient=85°C, Rth=5°C/W, Tj=125°C Tambient=85°C, Rth=60°C/W, Tj=125°C Rifb Recommended Ifb resistor (2)(3) Pulse min. Minimum turn-on pulse width Fmax. Maximum operating frequency 2) If Rifb is too low, the device can be damaged. 3) If Rifb is too high, the device may not switch on. Min. Max. Units ⎯ ⎯ 14 3.9 3.5 A Iout www.irf.com 0.5 1 ⎯ kΩ ms Hz ⎯ 200 2 IR3315(S)PbF Protection Characteristics Tj=25°C, Rifb=500 to 5kΩ Symbol Parameter Vifb-Vin@Isd Tsd OV Isdf Isd_1k Treset Min. pulse WAIT Rds(on) rev. Over-current shutdown threshold Over temperature threshold Over voltage protection (not latched) Fixed over current shutdown Programmable over current shutdown 1k Time to reset protection Min. pulse width (no WAIT state) WAIT function timer Reverse battery On state resistance Min. Typ. Max. Units 4 5.6 39 47 16 500 1200 2 28 V °C V 200 0.4 10 4.7 165 35 38 12 50 400 1 16 ms mΩ Min. Typ. Max. Units 6 ⎯ V ⎯ 1.5 32 5 1.5 6 6.2 5.8 1 5 mA ⎯ 3 5.4 4.9 0.4 1.2 Min. Typ. Max. Units 3 1 2 11 4 8 0.2 40 8 0.1 27 10 20 µs ⎯ mJ ⎯ 33 30 9 ⎯ ⎯ A µs Test Conditions See fig. 5 Vifb<Vifb-Vin@Isd Rifb=1kΩ See fig. 5 See fig. 4 and 5 Vcc-Vin=-14V, Iout=10A Static Electrical Characteristics Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Parameter Vcc op. Icc off Operating Voltage range Supply leakage current Iin, on Vih Vil Vhyst Iout On state IN positive current High level Input threshold voltage (4) Low level Input threshold voltage (4) Input hysteresis Vih-Vil Drain to source leakage current ⎯ 4 0.2 µA Test Conditions Vin=Vcc, Vcc-Vout=14V, Vcc-Vifb=14V Vcc-Vin=14V V Vin=Vcc, Vcc-Vifb=0V, Vcc-Vout=14V Rds(on) On state resistance (5) Tj=25°C 10 15 20 Iout=10A, Vcc-Vin=14V On state resistance (5) Tj=25°C 10 16 28 Iout=7A, Vcc-Vin=6V mΩ On state resistance (5) Tj=150°C 20 28.5 38 Iout=10A, Vcc-Vin=14V ⎯ Iout=50mA V clamp1 Vcc to Vout clamp voltage 1 36 39 V ⎯ 40 43 Iout=10A V clamp2 Vcc to Vout clamp voltage 2 (4) Input thresholds are measured directly between the input pin and the tab. Any parasitic resistance in common between the load current path and the input signal path can significantly affect the thresholds. (5) Rdson is measured between the tab and the Out pin, 5mm away from the package. µA Switching Electrical Characteristics Vcc=14V, Resistive load=4Ω, Tj=25°C Symbol Parameter Tdon Tr1 Tr2 Eon Tdoff Tf Eoff Turn on delay time to 10% Vcc Rise time to Vcc-Vout=5V Rise time to Vcc-Vout=0.1Vcc Turn on energy Turn off delay time Fall time to Vout=10% of Vcc Turn off energy www.irf.com ⎯ 10 2 ⎯ 100 20 µs ⎯ mJ Test Conditions See figure 2 3 IR3315(S)PbF Current Sense Characteristics Symbol Parameter Min. Typ. Max. Ratio I Load/Iifb current ratio 2,400 2,800 3,200 Ratio_TC Offset Trst I Load/Iifb variation aver temperature Load current diagnostic offset Ifb response time (low signal) -5 -0.08 ⎯ +5 +0.07 0 1 ⎯ Units ⎯ % A µs ⎯ Test Conditions Tj=25°C, Rfb=500Ω, Iout=20A Tj=-40°C to 150°C Iout=1A 90% of the Iout step Functional Block Diagram All values are typical VCC Driver Charge Pump 43V On/Off Fast turn-off 3mA 43V 38V + + 35V 43V Reset Set Latch Q Wait timer 1 ms - timer 4.7V 80Ω 400µs + Iout > 38A Tj > 165°C IN www.irf.com + Min. Pulse reverse battery protection IFB OUT 4 IR3315(S)PbF Lead Assignments 3- Vcc 3- Vcc 1- In 2- Ifb 3- Vcc (tab) 4- Out 5- Out 12 45 D²Pak 1 2 3 4 5 TO220 90% Vcc-Vin Vih Vil Vhyst Icc Vcc IN Iin Ifb Ifb Vcc-Vout Vclamp1 Vclamp2 IR3315 10% Tr-in 90% Vcc-5V Vout Out 10% Iout Isd Figure 1 – Voltages and current definitions www.irf.com Vcc-Vin Td on Td off Tf Tr1 Tr2 Figure 2 – Switching time definitions 5 IR3315(S)PbF T clamp Vin Vcc-Vin Iout T min. pulse Vcc T min. pulse Wait Iout Vout Vcc - V clamp See Application Notes to evaluate power dissipation Figure 3 – Active clamp waveforms Figure 4 – Min. pulse and Wait function Vcc-Vin t < T reset t > T reset t < T reset Wait t > T reset Wait Over-current shutdown Iout Over-temperature shutdown Tj Figure 5 – Protection Timing Diagrams www.irf.com 6 IR3315(S)PbF All curves are typical characteristics. Operation in hatched areas is not recommended. Tj=25°C, Rifb=500ohm, Vcc=14V (unless otherwise specified). 10 Icc off, supply leakage current (µA) 6 Icc, supply current (mA) 8 6 4 2 0 0 10 20 30 40 50 5 4 3 2 1 0 -50 0 Vcc-Vin, supply voltage (V) 100 150 Tj, junction temperature (°C) Figure 6 – Icc (mA) Vs Vcc-Vin (V) Figure 7 – Icc off (µA) Vs Tj (°C) 200% 6 5 Vih, Vil and Vifb-Vin@Isd (V) Rds(on), Drain-to-Source On Resistance (Normalized) 50 150% 100% 4 Vifb-Vin@Isd VIH 3 VIL 2 1 0 50% -50 0 50 100 Tj, junction temperature (°C) Figure 8 - Normalized Rds(on) (%) Vs Tj (°C) www.irf.com 150 -50 -25 0 25 50 75 100 125 150 Tj, junction temperature (°C) Figure 9 – Vih, Vil and Vifb-Vin@Isd (V) Vs Tj (°C) 7 IR3315(S)PbF 100 6 Isd, over current shutdown (A) With calibration Spec. Max. Error (+/-A) 4 2 0 10 1 0 5 10 15 20 25 30 100 1000 10000 Rifb, feedback resistor (Ω) I load, load current (A) Figure 11 – Ids (A) Vs Rifb (Ω) Figure 10 – Error (+/- A) Vs I load (A) 15 100 60°C/W Max. output current (A) Max. output current (A) 35°C/W 10 5 0 10 1 -50 0 50 100 Tamb., ambient temperature (°C) Figure 12 – Max. Iout (A) Vs Tamb. (°C) www.irf.com 150 10 100 Inductance (µH) Figure 13 – Max. Iout (A) Vs inductance (µH) 8 IR3315(S)PbF 100 Tamb=25°C Ids, output current (A) Tamb=100°C 10 1 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 Protection response time (s) Figure 14 – Ids (A) Vs over temperature protection response time (s) www.irf.com Zth, transient thermal impedance (°C/W) 100 50°C/W free air 10 5°C/W 1 0.1 0.01 1E-4 1E-3 1E-2 1E-1 1E+0 1E+1 1E+2 Time (s) Figure 15 – Transient thermal impedance (°C/W) Vs time (s) 9 IR3315(S)PbF Case Outline – TO220 5 leads - Automotive Q100 PbF qualified www.irf.com 10 IR3315(S)PbF Case Outline 5 Lead - D2PAK - Automotive Q100 PbF MSL1 qualified www.irf.com 11 IR3315(S)PbF Tape & Reel 5 Lead - D2PAK D2Pak is MSL1 qualified. This product has been designed and qualified for the Automotive [Q100] market. Qualification standards can be found at www.irf.com IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. 9/6/2006 www.irf.com 12 Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/