November 3, 2011 SMD INDUCTOR DR333-1 SERIES Features Low Profile Surface Mount Design Inductance Range from 1.0µH to 330µH Operating Temp. -20°C to +80°C Tinned Leads with Leaded Solder is Available (note 7) ELECTRICAL SPECIFICATIONS AT 25ºC Part No. DR333-1-102 DR333-1-122 DR333-1-152 DR333-1-182 DR333-1-222 DR333-1-272 DR333-1-332 DR333-1-392 DR333-1-472 DR333-1-562 DR333-1-682 DR333-1-822 DR333-1-103 DR333-1-123 DR333-1-153 DR333-1-183 DR333-1-223 DR333-1-273 DR333-1-333 DR333-1-393 DR333-1-473 DR333-1-563 DR333-1-683 DR333-1-823 DR333-1-104 DR333-1-124 DR333-1-154 DR333-1-184 DR333-1-224 DR333-1-274 DR333-1-334 Inductance (H) 1.0 20% 1.2 20% 1.5 20% 1.8 20% 2.2 20% 2.7 20% 3.3 20% 3.9 20% 4.7 20% 5.6 20% 6.8 20% 8.2 20% 10.0 20% 12.0 20% 15.0 20% 18.0 20% 22.0 10% 27.0 10% 33.0 10% 39.0 10% 47.0 10% 56.0 10% 68.0 10% 82.0 10% 100.0 10% 120.0 10% 150.0 10% 180.0 10% 220.0 10% 270.0 10% 330.0 10% @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 7.96MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 2.52MHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V @ 1kHz, 0.25V DCR () Max. 0.045 0.050 0.055 0.070 0.085 0.100 0.120 0.125 0.135 0.145 0.20 0.25 0.32 0.35 0.46 0.52 0.65 0.75 0.92 1.12 1.27 1.50 2.00 2.15 2.80 3.40 4.20 4.50 5.70 8.50 9.50 I rated (A) Max. 2.20 2.10 1.70 1.65 1.60 1.40 1.04 1.00 1.00 0.95 0.95 0.92 0.90 0.85 0.75 0.70 0.60 0.55 0.50 0.48 0.45 0.30 0.26 0.23 0.20 0.18 0.16 0.15 0.14 0.10 0.09 MECHANICAL OUTLINES 3.0 ± 0.3 XXX Notes: 1. 2. 3. 4. 5. 6. 7. All dimensions are shown in millimeters “mm” [inches “in”]. General tolerance 0.25mm [0.010 in.], unless otherwise specified. Irated for an approximate 40°C temperature rise for 20% drop maximum of the nominal value. Tape and reel quantity, 2000 pcs/reel Terminal finish is compliant to RoHS requirements Solder in accordance with J-STD-002 Rev. D Non-RoHS series parts 42-333-1-XXX are finished with leaded solder Sn60Pb40 or equivalent 3.5 ± 0.3 2.0 ± 0.3 TOP VIEW SIDE VIEW 3.5 1.6 0.8 1.6 BOTTOM VIEW DATATRONIC: 28151Highway 74, Romoland, CA 92585 PCB PAD LAYOUT (REF.) Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice.