LINER LTM4630-1 Dual 25a or single 50a î¼module regulator with 0.8% dc and 3% transient accuracy Datasheet

LTM4650-1
Dual 25A or Single 50A
µModule Regulator with 0.8% DC
and 3% Transient Accuracy
Description
Features
±0.8% Maximum Total DC Output Error Over Line
and Load (LTM4650-1A)
nn ±3% Transient Output Error with Minimum
Output Capacitance
nn Dual 25A or Single 50A Output
nn 4.5V to 15V Input, 0.6V to 1.8V Output Voltage Range
nn Differential Remote Sense Amplifier
nn Current Mode Control/Fast Transient Response
nn Current Sharing Up to 300A
nn 16mm × 16mm × 5.01mm BGA Package
nn
Applications
nn
nn
FPGA, ASIC, µProcessor Core Voltage Regulation
Information, Communication Systems
The LTM®4650-1A/LTM4650-1B is dual 25A or single 50A
output step-down µModule® (power module) regulator
with ±0.8% (LTM4650-1A) and ±1.5% (LTM4650-1B)
total DC output error with ±3% transient output error.
Included in the package are the switching controller,
power FETs, inductors, and all supporting components.
External compensation allows for fast transient response
to minimize output capacitance when powering FPGAs,
ASICs, and processors. With synchronized multiphase
parallel current sharing, six LTM4650-1 devices can deliver up to 300A. The LTM4650-1 is offered in a 16mm ×
16mm × 5.01 BGA package, with SnPb (BGA) or RoHS
compliant terminal finish.
L, LT, LTC, LTM, Linear Technology, the Linear logo, µModule, Burst Mode, LTpowerCAD and
PolyPhase are registered trademarks of Linear Technology Corporation. All other trademarks are
the property of their respective owners. Protected by U.S. Patents, including 5481178, 5705919,
5929620, 6100678, 6144194, 6177787, 6304066 and 6580258. Other patents pending.
Typical Application
50A, 1.0V Output DC/DC µModule Regulator
VOUT1
VIN
22µF
* 25V
×4
220µF
CERAMIC
4V
×6
120k
TEMP
DIFFOUT
RUN1
VOUTS2
RUN2
TRACK1
0.1µF
4.7µF
VFB2
TRACK2
COMP1
INTVCC
COMP2
10k
121k
90
68pF
VFB1
LTM4650-1
90.9k
3.24k
10nF
PGOOD1
PINS NOT USED
IN THIS CIRCUIT:
CLKOUT
EXTVCC
SW1
SW2
VOUTS1
1.0V Output Efficiency, fSW = 500kHz
95
EFFICIENCY (%)
VIN
4.5V TO
15V
PGOOD2
DIFFP
fSET
VOUT2
85
80
75
70
VOUT2
1.0V
50A
PHASMD SGND GND MODE_PLLIN DIFFN
65
VIN = 12V
VIN = 5V
0
10
20
30
LOAD CURRENT (A)
40
50
46501 TA01b
46501 TA01a
25% Load Step Transient Response, ±3% Output Regulation Window. 12VIN, 1.0VOUT, 50A with 6x 220μF Ceramic Cap
VOUT
20mV/DIV
AC-COUPLED
54mV
LOAD STEP
10A/DIV
12.5A STEP
50µs/DIV
46501 TA01c
*SEE DEMO CIRCUIT DC2479A-B
46501fc
For more information www.linear.com/LTM4650-1
1
LTM4650-1
Absolute Maximum Ratings
Pin Configuration
(Note 1)
TOP VIEW
VIN...............................................................–0.3V to 16V
VSW1, VSW2.....................................................–1V to 16V
PGOOD1, PGOOD2, RUN1, RUN2,
INTVCC , EXTVCC........................................... –0.3V to 6V
MODE_PLLIN, fSET, TRACK1, TRACK2,
DIFFOUT, PHASMD................................ –0.3V to INTVCC
VOUT1, VOUT2, VOUTS1, VOUTS2 (Note 6)......... –0.3V to 6V
DIFFP, DIFFN.......................................... –0.3V to INTVCC
INTVCC Peak Output Current.................................100mA
Internal Operating Temperature Range
(Note 2).............................................. –40°C to 125°C
Storage Temperature Range................... –55°C to 125°C
Peak Package Body Temperature........................... 245°C
TEMP
EXTVCC
M
L
VIN
K
J
CLKOUT
SW1
PHASMD
MODE_PLLIN
TRACK1
VFB1
VOUTS1
INTVCC
SW2
PGOOD1
PGOOD2
RUN2
DIFFOUT
DIFFP
DIFFN
H
G
RUN1
SGND
F
GND
COMP1 COMP2
E
SGND VFB2 TRACK2
D
GND
fSET SGND VOUTS2
C
B
VOUT1
VOUT2
GND
A
1
2
3
4
5
6
7
8
9
10
11
12
BGA PACKAGE
144-LEAD (16mm × 16mm × 5.01mm)
TJMAX = 125°C, θJA = 7°C/W, θJCbottom = 1.5°C/W,
θJCtop = 3.7°C/W, θJB + θJBA ≅ 7°C/W
θ VALUES DEFINED PER JESD 51-12
WEIGHT = 3.5g
Order Information
http://www.linear.com/product/LTM4650-1#orderinfo
PART MARKING*
PART NUMBER
PAD OR BALL FINISH
LTM4650EY-1A#PBF
SAC305 (RoHS)
DEVICE
FINISH CODE
PACKAGE
TYPE
MSL
RATING
TOTAL DC
ACCURACY
TEMPERATURE
RANGE (Note 2)
LTM4650Y-1
e1
BGA
3
±0.8%
–40°C to 125°C
LTM4650IY-1A#PBF
SAC305 (RoHS)
LTM4650Y-1
e1
BGA
3
±0.8%
–40°C to 125°C
LTM4650EY-1B#PBF
SAC305 (RoHS)
LTM4650Y-1
e1
BGA
3
±1.5%
–40°C to 125°C
LTM4650IY-1B#PBF
SAC305 (RoHS)
LTM4650Y-1
e1
BGA
3
±1.5%
–40°C to 125°C
LTM4650IY-1A
SnPb (63/37)
LTM4650Y-1
e0
BGA
3
±0.8%
–40°C to 125°C
LTM4650IY-1B
SnPb (63/37)
LTM4650Y-1
e0
BGA
3
±1.5%
–40°C to 125°C
Consult Marketing for parts specified with wider operating temperature
ranges. *Device temperature grade is indicated by a label on the shipping
container. Pad or ball finish code is per IPC/JEDEC J-STD-609.
• Terminal Finish Part Marking:
www.linear.com/leadfree
2
• Recommended BGA PCB Assembly and Manufacturing Procedures:
www.linear.com/umodule/pcbassembly
• BGA Package and Tray Drawings:
www.linear.com/packaging
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Electrical Characteristics
The l denotes the specifications which apply over the specified internal
operating temperature range. Specified as each individual output channel. TA = 25°C (Note 2), VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 24.
SYMBOL
PARAMETER
CONDITIONS
VIN
Input DC Voltage
l
4.5
15
V
VOUT
Output DC Voltage
l
0.6
1.8
V
VOUT1(DC),
VOUT2(DC)
Output Voltage, Total Variation with
Line and Load
l
l
1.190
1.182
1.210
1.218
V
V
1.40
V
CIN = 22µF × 3, COUT = 100µF × 2 Ceramic,
470µF POSCAP
VIN = 12V, VOUT = 1.2V, IOUT = 0A to 25A
A-Grade (0.8%)
B-Grade (1.5%)
MIN
TYP
MAX
UNITS
Input Specifications
VRUN1, VRUN2
RUN Pin On/Off Threshold
RUN Rising
1.1
VRUN1HYS , VRUN2HYS RUN Pin On Hysteresis
1.25
150
mV
IINRUSH(VIN)
Input Inrush Current at Start-Up
IOUT = 0A, CIN = 22µF × 3, CSS = 0.01µF,
COUT = 100µF × 3, VOUT = 1.2V
IQ(VIN)
Input Supply Bias Current
(Both Channel Running
VIN = 12V, VOUT = 1.2V, Burst Mode Operation
VIN = 12V, VOUT = 1.2V, Pulse-Skipping Mode
VIN = 12V, VOUT= 1.2V, Switching Continuous
Shutdown, RUN = 0, VIN = 12V
4.5
25
240
35
mA
mA
mA
µA
IS(VIN)
Input Supply Current
VIN = 4.5V, VOUT = 1.2V, IOUT = 25A
VIN = 12V, VOUT = 1.2V, IOUT = 25A
8.4
3.2
A
A
IOUT1(DC), IOUT2(DC)
Output Continuous Current Range
VIN = 12V, VOUT = 1.2V (Note 6)
ΔVOUT1(LINE) /VOUT1
ΔVOUT2(LINE) /VOUT2
Line Regulation Accuracy
VOUT = 1.2V, VIN from 4.5V to 15V
IOUT = 0A for Each Output,
ΔVOUT1/VOUT1
ΔVOUT2 /VOUT2
Load Regulation Accuracy
For Each Output, VOUT = 1.2V, 0A to 25A
VIN = 12V (Note 6)
A-Grade
B-Grade
1
A
Output Specifications
0
l
l
l
25
A
0.01
0.1
%/V
0.1
0.2
0.4
0.75
%
%
VOUT1(AC), VOUT2(AC) Output Ripple Voltage
For Each Output, IOUT = 0A, COUT = 100µF × 3
Ceramic, 470µF POSCAP, VIN = 12V,
VOUT = 1.2V, Frequency = 500kHz
fS (Each Channel)
Output Ripple Voltage Frequency
VIN = 12V, VOUT = 1.2V, fSET = 1.25V (Note 4)
fSYNC
(Each Channel)
SYNC Capture Range
∆VOUTSTART
(Each Channel)
Turn-On Overshoot
COUT = 100µF Ceramic, 470µF POSCAP,
VOUT = 1.2V, IOUT = 0A VIN = 12V
10
mV
tSTART
(Each Channel)
Turn-On Time
COUT = 100µF Ceramic, 470µF POSCAP,
No Load, TRACK/SS with 0.01µF to GND,
VIN = 12V
5
ms
∆VOUT(LS)
(Each Channel)
Peak Deviation for Dynamic Load
Load: 0% to 50% to 0% of Full Load
COUT = 22µF × 3 Ceramic, 470µF POSCAP
VIN = 12V, VOUT = 1.2V
30
mV
15
mVP-P
500
400
kHz
780
kHz
46501fc
For more information www.linear.com/LTM4650-1
3
LTM4650-1
Electrical Characteristics
The l denotes the specifications which apply over the specified internal
operating temperature range. Specified as each individual output channel. TA = 25°C (Note 2), VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 24.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
tSETTLE
(Each Channel)
Settling Time for Dynamic Load
Step
Load: 0% to 50% to 0% of Full Load,
VIN = 12V, COUT = 100µF, 470µF POSCAP
20
µs
IOUT(PK)
(Each Channel)
Output Current Limit
VIN = 12V, VOUT = 1.2V
35
A
Voltage at VFB Pins
IOUT = 0A, VOUT = 1.2V
A-Grade
B-Grade
Control Section
VFB1, VFB2
IFB
l
l
0.596
0.594
0.600
0.600
l
0.64
1
1.3
(Note 5)
VOVL
Feedback Overvoltage Lockout
TRACK1 (I),
TRACK2 (I)
Track Pin Soft-Start Pull-Up Current
UVLO
Undervoltage Lockout (Falling)
TRACK1 (I),TRACK2 (I) Start at 0V
0.604
0.606
V
V
–5
–20
nA
0.66
0.68
V
1.5
µA
3.3
UVLO Hysteresis
tON(MIN)
Minimum On-Time
(Note 5)
RFBHI1, RFBHI2
Resistor Between VOUTS1, VOUTS2
and VFB1, VFB2 Pins for Each Output
VPGOOD1, VPGOOD2
Low
PGOOD Voltage Low
IPGOOD = 2mA
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPGOOD
PGOOD Trip Level
VFB with Respect to Set Output Voltage
VFB Ramping Negative
VFB Ramping Positive
60.05
V
0.6
V
90
ns
60.4
60.75
0.1
0.3
V
±5
µA
–10
10
kΩ
%
%
INTVCC Linear Regulator
VINTVCC
Internal VCC Voltage
6V < VIN < 15V
VINTVCC
Load Regulation
INTVCC Load Regulation
ICC = 0mA to 50mA
VEXTVCC
EXTVCC Switchover Voltage
EXTVCC Ramping Positive
VEXTVCC(DROP)
EXTVCC Dropout
ICC = 20mA, VEXTVCC = 5V
VEXTVCC(HYST)
EXTVCC Hysteresis
4.8
4.5
5
5.2
V
0.75
2
%
4.7
50
V
100
220
mV
mV
Oscillator and Phase-Locked Loop
Frequency Nominal
Nominal Frequency
fSET = 1.2V
Frequency Low
Lowest Frequency
fSET = 0.93V
Frequency High
Highest Frequency
fSET > 2.4V, Up to INTVCC
fSET
Frequency Set Current
RMODE_PLLIN
MODE_PLLIN Input Resistance
CLKOUT
Phase (Relative to VOUT1)
CLK High
CLK Low
Clock High Output Voltage
Clock Low Output Voltage
4
450
500
550
400
kHz
780
9
PHASMD = GND
PHASMD = Float
PHASMD = INTVCC
2
10
kHz
kHz
11
µA
250
kΩ
60
90
120
Deg
Deg
Deg
0.2
V
V
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Electrical Characteristics
The l denotes the specifications which apply over the specified internal
operating temperature range. Specified as each individual output channel. TA = 25°C (Note 2), VIN = 12V and VRUN1, VRUN2 at 5V
unless otherwise noted. Per the typical application in Figure 24.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Differential Amplifier
AV Differential
Amplifier
Gain
RIN
Input Resistance
Measured at DIFFP Input
VOS
Input Offset Voltage
VDIFFP = VDIFFOUT = 1.2V, IDIFFOUT = 100µA
PSRR Differential
Amplifier
Power Supply Rejection Ratio
5V < VIN < 15V
ICL
Maximum Output Current
VOUT(MAX)
Maximum Output Voltage
GBW
Gain Bandwidth Product
VTEMP
Diode Connected PNP
TC
Temperature Coefficient
1
V/V
80
kΩ
3
IDIFFOUT = 300µA
mV
90
dB
3
mA
INTVCC – 1.4
V
3
I = 100µA
l
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTM4650-1 is tested under pulsed load conditions such that
TJ ≈ TA. The LTM4650-1E is guaranteed to meet specifications from
0°C to 125°C internal temperature. Specifications over the –40°C to
125°C internal operating temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTM4650-1I is guaranteed over the full –40°C to 125°C internal operating
temperature range. Note that the maximum ambient temperature
consistent with these specifications is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
impedance and other environmental factors.
MHz
0.6
V
–2.2
mV/C
Note 3: Two outputs are tested separately and the same testing condition
is applied to each output.
Note 4: LTM4650-1 device is designed to operate from 400kHz to 750kHz.
Note 5: These parameters are tested at wafer sort.
Note 6: See output current derating curves for different VIN, VOUT and TA.
Typical Performance Characteristics
95
Efficiency vs Output Current,
VIN = 12V
95
90
90
85
85
85
80
75
0.8VOUT, 400kHz
1.0VOUT, 500kHz
1.2VOUT, 500kHz
1.5VOUT, 600kHz
1.8VOUT, 600kHz
70
65
0
5
10
15
LOAD CURRENT (A)
20
80
75
0.8VOUT, 400kHz
1.0VOUT, 500kHz
1.2VOUT, 500kHz
1.5VOUT, 600kHz
1.8VOUT, 600kHz
70
25
46501 G01
EFFICIENCY (%)
90
EFFICIENCY (%)
EFFICIENCY (%)
95
Efficiency vs Output Current,
VIN = 5V
65
0
5
10
15
LOAD CURRENT (A)
20
Dual Phase Single Output Efficiency
vs Output Current, VIN = 12V,
fS = 500kHz
80
75
0.8VOUT, 400kHz
1.0VOUT, 500kHz
1.2VOUT, 500kHz
1.5VOUT, 600kHz
1.8VOUT, 600kHz
70
25
65
0
10
20
30
LOAD CURRENT (A)
40
50
46501 G02
46501 G03
46501fc
For more information www.linear.com/LTM4650-1
5
LTM4650-1
Typical Performance Characteristics
Burst Mode and Pulse-Skip Mode
Efficiency VIN=12V, VOUT = 1.2V,
fS = 500kHz
100
CCM
Burst Mode OPERATION
PULSE-SKIP MODE
90
80
EFFICIENCY (%)
1V Dual Phase Single Output
Load Transient Response
1.2V Dual Phase Single Output
Load Transient Response
VOUT(AC)
20mV/DIV
VOUT(AC)
20mV/DIV
70
60
LOAD
STEP
10A/DIV
LOAD
STEP
10A/DIV
50
40
30
50µs/DIV
12VIN, 1VOUT, 500kHz, 12.5A LOAD STEP,
10A/µs STEP-UP AND STEP-DOWN
COUT = 6× 220µF CERAMIC
CFF = 68pF
20
10
0
0.01
0.1
1
LOAD CURRENT (A)
46501 G05
50µs/DIV
12VIN, 1.2VOUT, 500kHz, 12.5A LOAD STEP,
10A/µs STEP-UP AND STEP-DOWN
COUT = 6× 220µF CERAMIC
CFF = 68pF
46501 G06
10
46501 G04
1.5V Dual Phase Single Output
Load Transient Response
1.8V Dual Phase Single Output
Load Transient Response
Single Phase Start-Up with No load
VSW
10V/Div
VOUT(AC)
20mV/DIV
VOUT(AC)
20mV/DIV
VOUT
0.5V/Div
LOAD
STEP
10A/DIV
LOAD
STEP
10A/DIV
50µs/DIV
12VIN, 1.5VOUT, 600kHz, 12.5A LOAD STEP,
10A/µs STEP-UP AND STEP-DOWN
COUT = 6× 220µF CERAMIC
CFF = 68pF
46501 G07
IIN
0.2A/Div
50µs/DIV
12VIN, 1.8VOUT, 600kHz, 12.5A LOAD STEP,
10A/µs STEP-UP AND STEP-DOWN
COUT = 6× 220µF CERAMIC
CFF = 68pF
46501 G08
20ms/DIV
12VIN, 1.2VOUT, 500kHz
COUT = 1× 470µF POSCAP + 2× 100µF
CERAMIC, CSS = 0.1µF
Single Phase Short Circuit
Protection with 25A
Single Phase Short Circuit
Protection with No load
Single Phase Start-up with 25A
VSW
10V/Div
VSW
10V/Div
VSW
10V/Div
VOUT
0.5V/Div
VOUT
0.5V/Div
VOUT
0.5V/Div
IIN
1A/Div
IIN
2A/Div
IIN
1A/Div
50μs/DIV
12VIN, 1.2VOUT, 500kHz
COUT = 1× 470µF POSCAP + 2× 100µF
CERAMIC, CSS = 0.1µF
6
46501 G10
20ms/DIV
12VIN, 1.2VOUT, 500kHz
COUT = 1× 470µF POSCAP + 2× 100µF
CERAMIC, CSS = 0.1μF
46501 G09
46501 G11
50µs/DIV
12VIN, 1.2VOUT, 500kHz
COUT = 1× 470µF POSCAP + 2× 100µF
CERAMIC
46501 G12
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Pin Functions
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY.
VOUT1 (A1-A5, B1-B5, C1-C4): Power Output Pins. Apply
output load between these pins and GND pins. Recommend
placing output decoupling capacitance directly between
these pins and GND pins. Review Table 4.
GND (A6-A7, B6-B7, D1-D4, D9-D12, E1-E4, E10-E12,
F1-F3, F10-F12, G1, G3, G10, G12, H1-H7, H9-H12, J1,
J5, J8, J12, K1, K5-K8, K12, L1, L12, M1 , M12): Power
Ground Pins for Both Input and Output Returns.
VOUT2 (A8-A12, B8-B12, C9-C12): Power Output Pins.
Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly
between these pins and GND pins. Review Table 4.
VOUTS1, VOUTS2 (C5, C8): This pin is connected to the top
of the internal top feedback resistor for each output. The
pin can be directly connected to its specific output, or
connected to DIFFOUT when the remote sense amplifier
is used. In paralleling modules, one of the VOUTS pins is
connected to the DIFFOUT pin in remote sensing or directly
to VOUT with no remote sensing. It is very important to
connect these pins to either the DIFFOUT or VOUT since
this is the feedback path, and cannot be left open. See the
Applications Information section.
fSET (C6): Frequency Set Pin. A 10µA current is sourced
from this pin. A resistor from this pin to ground sets a
voltage that in turn programs the operating frequency.
Alternatively, this pin can be driven with a DC voltage
that can set the operating frequency. See the Applications
Information section.
SGND (C7, D6, G6-G7, F6-F7): Signal Ground Pin. Return
ground path for all analog and low power circuitry. Tie a
single connection to the output capacitor GND in the application. See layout guidelines in Figure 13.
VFB1, VFB2 (D5, D7): The Negative Input of the Error
Amplifier for Each Channel. Internally, this pin is connected to VOUTS1 or VOUTS2 with a 60.4kΩ precision
resistor. Different output voltages can be programmed
with an additional resistor between VFB and GND pins. In
PolyPhase® operation, tying the VFB pins together allows
for parallel operation. See the Applications Information
section for details.
TRACK1, TRACK2 (E5, D8): Output Voltage Tracking Pin
and Soft-Start Inputs. Each channel has a 1.3µA pull-up
current source. When one channel is configured to be
master of the two channels, then a capacitor from this pin
to ground will set a soft-start ramp rate. The remaining
channel can be set up as the slave, and have the master’s
output applied through a voltage divider to the slave output’s track pin. This voltage divider is equal to the slave
output’s feedback divider for coincidental tracking. See
the Applications Information section.
COMP1, COMP2 (E6, E7): Current control threshold and
error amplifier compensation point for each channel. The
current comparator threshold increases with this control
voltage. COMP pin internal has 10pF filter cap to SGND.
An external RC filter circuit is required for control loop
compensation. See Applications Information section. Tie
the COMP pins together for parallel operation. Do not
drive this pin.
DIFFP (E8): Positive input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output voltage. See the Applications Information section.
DIFFN (E9): Negative input of the remote sense amplifier.
This pin is connected to the remote sense point of the
output GND. See the Applications Information section.
46501fc
For more information www.linear.com/LTM4650-1
7
LTM4650-1
Pin Functions
(Recommended to Use Test Points to Monitor Signal Pin Connections.)
MODE_PLLIN (F4): Force Continuous Mode, Burst Mode
Operation, or Pulse-Skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to SGND to force both channels into
force continuous mode of operation. Connect to INTVCC
to enable pulse-skipping mode of operation. Leaving the
pin floating will enable Burst Mode operation. A clock on
the pin will force both channels into continuous mode of
operation and synchronized to the external clock applied
to this pin.
RUN1, RUN2 (F5, F9): Run Control Pin. A voltage above
1.25V will turn on each channel in the module. A voltage
below 1.25V on the RUN pin will turn off the related channel. Each RUN pin has a 1µA pull-up current, once the
RUN pin reaches 1.2V an additional 4.5µA pull-up current
is added to this pin.
DIFFOUT (F8): Internal Remote Sense Amplifier Output.
Connect this pin to VOUTS1 or VOUTS2 depending on which
output is using remote sense. In parallel operation connect one of the VOUTS pin to DIFFOUT for remote sensing.
SW1, SW2 (G2, G11): Switching node of each channel
that is used for testing purposes. Also an R-C snubber
network can be applied to reduce or eliminate switch node
ringing, or otherwise leave floating. See the Applications
Information section.
PHASMD (G4): Connect this pin to SGND, INTVCC, or floating this pin to select the phase of CLKOUT to 60 degrees,
120 degrees, and 90 degrees respectively.
8
CLKOUT (G5): Clock output with phase control using the
PHASMD pin to enable multiphase operation between
devices. See the Applications Information section.
PGOOD1, PGOOD2 (G9, G8): Output Voltage Power
Good Indicator. Open drain logic output that is pulled to
ground when the output voltage is not within ±10% of
the regulation point.
INTVCC (H8): Internal 5V Regulator Output. The control
circuits and internal gate drivers are powered from this
voltage. Decouple this pin to PGND with a 4.7µF low ESR
tantalum or ceramic. INTVCC is activated when either RUN1
or RUN2 is activated.
TEMP (J6): Temperature Monitor. An internal diode connected NPN transistor between this pin and SGND with
10nF filtering capacitor. See the Applications Information
section.
EXTVCC (J7): External power input that is enabled through
a switch to INTVCC whenever EXTVCC is greater than 4.7V.
Do not exceed 6V on this input, and connect this pin to
VIN when operating VIN on 5V. An efficiency increase will
occur that is a function of the (VIN – INTVCC) multiplied by
power MOSFET driver current. Typical current requirement
is 30mA. VIN must be applied before EXTVCC , and EXTVCC
must be removed before VIN.
VIN (M2-M11, L2-L11, J2-J4, J9-J11, K2-K4, K9-K11):
Power Input Pins. Apply input voltage between these pins
and GND pins. Recommend placing input decoupling
capacitance directly between VIN pins and GND pins.
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Simplified Block Diagram
PGOOD1
TRACK1
SS CAP
VIN
= 100µA VIN
RT
OR TEMP
MONITORS
VIN
4.5V TO 15V
VIN
CIN1
22µF
25V
×2
1μF
GND
RT
TEMP
MTOP1
SW1
CLKOUT
0.12µH
RUN1
MODE_PLLIN
0.22µF
MBOT1
PHASEMD
VOUT1
1.5V
25A
VOUT1
+
GND
COUT1
VOUTS1
COMP1
RTH1
60.4k
VFB1
10pF
CTH1
SGND
RFB1
40.2k
POWER
CONTROL
PGOOD2
TRACK2
VIN
INTVCC
SS CAP
4.7µF
CIN2
22µF
25V
×2
1μF
0.22µF
GND
EXTVCC
MTOP2
SW2
0.12µH
RUN2
VOUT2
0.22µF
MBOT2
GND
+
VOUT2
1.2V
25A
COUT2
VOUTS2
60.4k
COMP2
VFB2
RFB2
60.4k
10pF
RTH2
CTH2
+ –
fSET
RFSET
SGND
INTERNAL
FILTER
DIFFOUT
DIFFN
DIFFP
46501 F01
Figure 1. Simplified LTM4650-1 Block Diagram
Decoupling Requirements
TA = 25°C. Use Figure 1 configuration.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
CIN1, CIN2
External Input Capacitor Requirement
(VIN1 = 4.5V to 15V, VOUT1 = 1.5V)
(VIN2 = 4.5V to 15V, VOUT2 = 1.0V)
IOUT1 = 25A
IOUT2 = 25A
44
44
66
66
µF
µF
External Output Capacitor Requirement
(VIN1 = 4.5V to 15V, VOUT1 = 1.5V)
(VIN2 = 4.5V to 15V, VOUT2 = 1.0V)
IOUT1 = 25A
IOUT2 = 25A
600
600
800
800
µF
µF
COUT1
COUT2
MAX
UNITS
46501fc
For more information www.linear.com/LTM4650-1
9
LTM4650-1
Operation
Power Module Description
The LTM4650-1 is a dual-output standalone nonisolated
switching mode DC/DC power supply with ±0.8% (A-Grade)
total DC output error over line, load and temperature variation. It can provide two 25A outputs with few external input
and output capacitors and setup components. This module
provides precisely regulated output voltages programmable
via external resistors from 0.6VDC to 1.8VDC over 4.5V to
15V input voltages. The typical application schematic is
shown in Figure 24.
The LTM4650-1 has dual integrated constant-frequency
current mode regulators and built-in power MOSFET
devices with fast switching speed. The typical switching
frequency is from 400kHz to 600kHz depending on output
voltage. For switching-noise sensitive applications, it can
be externally synchronized from 400kHz to 780kHz. A
resistor can be used to program a free run frequency on
the FSET pin. See the Applications Information section.
With current mode control, the LTM4650-1 module has
sufficient stability margins and good transient performance with a wide range of output capacitors, even with
all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limit and foldback current limit in an overcurrent condition.
Internal overvoltage and undervoltage comparators pull
the open-drain PGOOD outputs low if the output feedback
voltage exits a ±10% window around the regulation point.
As the output voltage exceeds 10% above regulation, the
bottom MOSFET will turn on to clamp the output voltage.
The top MOSFET will be turned off. This overvoltage protect
is feedback voltage referred.
Pulling the RUN pins below 1.1V forces the regulators into
a shutdown state, by turning off both MOSFETs. The TRACK
pins are used for programming the output voltage ramp and
voltage tracking during start-up or used for soft-starting
the regulator. See the Applications Information section.
10
The LTM4650-1 has a built-in 10pF high frequency filter
cap from COMP to SGND for each output. An external RC
filtering circuit is required to achieve fast Type II control
loop compensation. Table 4 provides a guide line for input,
output capacitances and RC comp values for several operating conditions. The Linear Technology µModule Power
Design Tool (LTpowerCAD®) will be provided for transient
and stability analysis. The VFB pin is used to program the
output voltage with a single external resistor to ground.
A differential remote sense amplifier is available for sensing the output voltage accurately on one of the outputs at
the load point, or in parallel operation sensing the output
voltage at the load point.
Multiphase operation can be easily employed with the
MODE_PLLIN, PHASMD, and CLKOUT pins. Up to
12 phases can be cascaded to run simultaneously with
respect to each other by programming the PHASMD pin to
different levels. See the Applications Information section.
High efficiency at light loads can be accomplished with
selectable Burst Mode operation or pulse-skipping operation using the MODE_PLLIN pin. These light load features
will accommodate battery operation. Efficiency graphs are
provided for light load operation in the Typical Performance
Characteristics section. See the Applications Information
section for details.
A general purpose temperature diode is included inside
the module to monitor the temperature of the module. See
the Applications Information section for details.
The switch pins are available for functional operation
monitoring and a resistor-capacitor snubber circuit can
be careful placed on the switch pin to ground to dampen
any high frequency ringing on the transition edges. See
the Applications Information section for details.
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
Output Total DC Accuracy and AC Transient
Performance
In modern ASIC and FPGA power supply designs, a tight
total voltage regulation window, ±3% for example, is required of the supply powering the core and periphery. To
meet this requirement, the supply’s DC voltage variance
plus any AC voltage variation which may occur during any
load step transient must fall within this allowed window.
The DC voltage variance is determined by the accuracies
of the supply’s reference voltage, resistor divider, load
regulation and line regulation over the operating temperature range. The AC voltage variance is determined by the
supply’s output voltage overshoot and undershoots in
response to a load transient condition for a given output
capacitor network.
Figure 2 shows a typical load step transient response
waveform together with DC voltage accuracy variance. For
a given allowable voltage regulation window, a tighter DC
voltage accuracy allows more margin for the AC variation
due to a load transient response. This increased margin
for AC variation allows for a reduction in the total output
capacitance required to meet the regulation window requirement. This allows for a reduced total solution cost
and footprint area.
LOAD STEP
For example, in an FPGA core voltage application, for a 12V
input, 0.9V output at 72A design, a total overall ±3% total
voltage regulation window is required in responding to a
25% load step transient. Figure 3 illustrates the benefit of
overall output capacitor reduction versus improved total
DC accuracy by using 100µF ceramic output capacitors.
5000
REQUIRED OUTPUT CAPACITANCE (µF)
The typical LTM4650-1 application circuit is shown in
Figure 24. External component selection is primarily
determined by the maximum load current and output
voltage. Refer to Table 4 for specific external capacitor
requirements for particular applications.
4700
4500
4000
3500
3200
3000
2500
2600
2200
2000
1500
1000
500
0
0.8
1.2
1.5
TOTAL DC ACCURACY (%)
2.0
46501 F03
Figure 3. Overall Output Capacitor vs Total DC Accuracy
VIN to VOUT Step-Down Ratios
There are restrictions in the maximum VIN and VOUT stepdown ratio that can be achieved for a given input voltage.
Each output of the LTM4650-1 is capable of 98% duty
cycle, but the VIN to VOUT minimum dropout is still shown
as a function of its load current and will limit output current capability related to high duty cycle on the top side
switch. Minimum on-time tON(MIN) is another consideration
in operating at a specified duty cycle while operating at
a certain frequency due to the fact that tON(MIN) < D/fSW,
where D is duty cycle and fSW is the switching frequency.
tON(MIN) is specified in the electrical parameters as 90ns.
Output Voltage Programming
AC OVERSHOOT
ALLOWABLE
REGULATION
WINDOW
DC ACCURACY
AC UNDERSHOOT
46501 F02
Figure 2. Typical Load Step Transient Response with DC Voltage
Accuracy Variance
The PWM controller has an internal 0.6V reference voltage.
As shown in the Block Diagram, a 60.4kΩ internal feedback
resistor connects between the VOUTS1 to VFB1 and VOUTS2
to VFB2. It is very important that these pins be connected
to their respective outputs for proper feedback regulation.
Overvoltage can occur if these VOUTS1 and VOUTS2 pins are
left floating when used as individual regulators, or at least
one of them is used in paralleled regulators. The output
voltage will default to 0.6V with no feedback resistor on
46501fc
For more information www.linear.com/LTM4650-1
11
LTM4650-1
Applications Information
either VFB1 or VFB2. Adding a resistor RFB from VFB pin to
GND programs the output voltage:
VOUT = 0.6V •
60.4k +RFB
RFB
Table 1. VFB Resistor Table vs Various Output Voltages
VOUT
0.6V
0.8V
0.9V
1.0V
1.2V
1.5V
1.8V
RFB
Open
182k
121k
90.9k
60.4k
40.2k
30.2k
For parallel operation of multiple channels the same feedback setting resistor can be used for the parallel design.
This is done by connecting the VOUTS1 to the output as
shown in Figure 4, thus tying one of the internal 60.4k
resistors to the output. All of the VFB pins tie together with
one programming resistor as shown in Figure 4.
COMP1 LTM4650-1
VOUT1
COMP2
VOUT2
60.4k
4 PARALLELED OUTPUTS
FOR 1.2V AT 100A
VOUTS1
VOUTS2
OPTIONAL CONNECTION
VFB1
TRACK1
60.4k
VFB2
TRACK2
COMP1 LTM4650-1
VOUT1
COMP2
VOUT2
RTH
60.4k
OPTIONAL
RFB
60.4k
USE TO LOWER
TOTAL EQUIVALENT
RESISTANCE TO LOWER
IFB VOLTAGE ERROR
VOUTS1
VOUTS2
CTH
VFB1
TRACK1
0.1µF
TRACK2
60.4k
VFB2
46501 F04
RFB
60.4k
Input Capacitors
The LTM4650-1 module should be connected to a low ACimpedance DC source. For the regulator input two 22µF
input ceramic capacitors are required for each channel
for RMS ripple current. A 47µF to 100µF surface mount
aluminum electrolytic bulk capacitor can be used for more
input bulk capacitance. This bulk input capacitor is only
needed if the input source impedance is compromised by
long inductive leads, traces or not enough source capacitance. If low impedance power planes are used, then this
bulk capacitor is not needed.
For a buck converter, the switching duty-cycle can be
estimated as:
D=
Figure 4. 4-Phase Parallel Configurations
In parallel operation, the VFB pins have an IFB current of 20nA
maximum each channel. To reduce output voltage error due
to this current, an additional VOUTS pin can be tied to VOUT,
and an additional RFB resistor can be used to lower the total
Thevenin equivalent resistance seen by this current. For
example in Figure 4, the total Thevenin equivalent resistance
of the VFB pin is (60.4k//RFB), which is 30.2k where RFB is
12
equal to 60.4k for a 1.2V output. Four phases connected
in parallel equates to a worse case feedback current of
4 • IFB = 80nA maximum. The voltage error is 80nA • 30.2k
= 2.4mV. If VOUTS2 is connected, as shown in Figure 2, to
VOUT, and another 60.4k resistor is connected from VFB2 to
ground, then the voltage error is reduced to 1.2mV. If the
voltage error is acceptable then no additional connections
are necessary. The onboard 60.4k resistor is 0.5% accurate
and the VFB resistor can be chosen by the user to be as
accurate as needed. All COMP pins are tied together for
current sharing between the phases. The TRACK/SS pins
can be tied together and a single soft-start capacitor can
be used to soft-start the regulator. The soft-start equation
will need to have the soft-start current parameter increased
by the number of paralleled channels. See Output Voltage
Tracking section.
VOUT
VIN
Without considering the inductor current ripple, for each
output, the RMS current of the input capacitor can be
estimated as:
IOUT(MAX)
ICIN(RMS) =
• D • (1−D)
η%
In the above equation, η% is the estimated efficiency of
the power module. The bulk capacitor can be a switcherrated electrolytic aluminum capacitor, Polymer capacitor.
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
Output Capacitors
Burst Mode Operation
The LTM4650-1 is designed for low output voltage ripple
noise and good transient response. The bulk output
capacitors defined as COUT are chosen with low enough
effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low
ESR tantalum capacitor, the low ESR polymer capacitor
or ceramic capacitor. The typical output capacitance
range for each output is from 400µF to 600µF. Additional
output filtering may be required by the system designer,
if further reduction of output ripples or dynamic transient
spikes is required. Table 4 shows a matrix of different
output voltages and output capacitors to minimize the
voltage droop and overshoot during a 12.5A (25%) and
25A (50%) load step transient. The table optimizes total
equivalent ESR and total bulk capacitance to optimize the
transient performance. Stability criteria are considered in
the Table 4 matrix, and the Linear Technology LTpowerCAD Design Tool will be provided for stability analysis.
In multi LTM4650-1 paralleling applications, Table 4 RC
compensation value is still valid in terms of having one
set of RC filters on each of the paralleling modules while
connecting all the COMP, FB and VOUT pins together. See
Figure 29 and Multiphase Operation section. Multiphase
operation will reduce effective output ripple as a function of
the number of phases. Application Note 77 discusses this
noise reduction versus output ripple current cancellation,
but the output capacitance should be considered carefully
as a function of stability and transient response. The Linear
Technology LTpowerCAD Design Tool can calculate the
output ripple reduction as the number of implemented
phases increases by N times. A small value 10Ω to 50Ω
resistor can be place in series from VOUT to the VOUTS pin
to allow for a bode plot analyzer to inject a signal into the
control loop and validate the regulator stability. The same
resistor could be place in series from VOUT to DIFFP and
a bode plot analyzer could inject a signal into the control
loop and validate the regulator stability.
The LTM4650-1 is capable of Burst Mode operation on
each regulator in which the power MOSFETs operate intermittently based on load demand, thus saving quiescent
current. For applications where maximizing the efficiency
at very light loads is a high priority, Burst Mode operation
should be applied. Burst Mode operation is enabled with
the MODE_PLLIN pin floating. During this operation, the
peak current of the inductor is set to approximately one
third of the maximum peak current value in normal operation even though the voltage at the COMP pin indicates
a lower value. The voltage at the COMP pin drops when
the inductor’s average current is greater than the load
requirement. As the COMP voltage drops below 0.5V, the
BURST comparator trips, causing the internal sleep line
to go high and turn off both power MOSFETs.
In sleep mode, the internal circuitry is partially turned off,
reducing the quiescent current to about 450µA for each
output. The load current is now being supplied from the
output capacitors. When the output voltage drops, causing COMP to rise above 0.5V, the internal sleep line goes
low, and the LTM4650-1 resumes normal operation. The
next oscillator cycle will turn on the top power MOSFET
and the switching cycle repeats. Either regulator can be
configured for Burst Mode operation.
Pulse-Skipping Mode Operation
In applications where low output ripple and high efficiency at intermediate currents are desired, pulse-skipping
mode should be used. Pulse-skipping operation allows
the LTM4650-1 to skip cycles at low output loads, thus
increasing efficiency by reducing switching loss. Tying
the MODE_PLLIN pin to INTVCC enables pulse-skipping
operation. At light loads the internal current comparator
may remain tripped for several cycles and force the top
MOSFET to stay off for several cycles, thus skipping cycles.
The inductor current does not reverse in this mode. This
mode will maintain higher effective frequencies thus lower
output ripple and lower noise than Burst Mode operation.
Either regulator can be configured for pulse-skipping mode.
46501fc
For more information www.linear.com/LTM4650-1
13
LTM4650-1
Applications Information
2-PHASE DESIGN
PHASMD
FLOAT
CLKOUT
0 PHASE
MODE_PLLIN
VOUT1
VOUT2
SGND
FLOAT
CONTROLLER1
0
0
0
CONTROLLER2
180
180
240
CLKOUT
60
90
120
180 PHASE
INTVCC
PHASMD
4-PHASE DESIGN
90 DEGREE
CLKOUT
0 PHASE
FLOAT
CLKOUT
MODE_PLLIN
VOUT1
VOUT2
180 PHASE
90 PHASE
FLOAT
PHASMD
MODE_PLLIN
VOUT1
VOUT2
270 PHASE
PHASMD
6-PHASE DESIGN
60 DEGREE
60 DEGREE
CLKOUT
0 PHASE
SGND
CLKOUT
MODE_PLLIN
VOUT1
VOUT2
PHASMD
180 PHASE
60 PHASE
SGND
CLKOUT
MODE_PLLIN
VOUT1
VOUT2
240 PHASE
PHASMD
120 PHASE
FLOAT
MODE_PLLIN
VOUT1
VOUT2
300 PHASE
PHASMD
46501 F05
Figure 5. Examples of 2-Phase, 4-Phase, and 6-Phase Operation with PHASMD Table
Forced Continuous Operation
Multiphase Operation
In applications where fixed frequency operation is more
critical than low current efficiency, and where the lowest
output ripple is desired, forced continuous operation should
be used. Forced continuous operation can be enabled by
tying the MODE_PLLIN pin to GND. In this mode, inductor current is allowed to reverse during low output loads,
the COMP voltage is in control of the current comparator
threshold throughout, and the top MOSFET always turns on
with each oscillator pulse. During start-up, forced continuous mode is disabled and inductor current is prevented
from reversing until the LTM4650-1’s output voltage is
in regulation. Either regulator can be configured for force
continuous mode.
For output loads that demand more than 25A of current, two
outputs in LTM4650-1 or even multiple LTM4650-1s can be
paralleled to run out of phase to provide more output current
without increasing input and output voltage ripples. The
MODE_PLLIN pin allows the LTM4650-1 to synchronize
to an external clock (between 400kHz and 780kHz) and the
internal phase-locked-loop allows the LTM4650-1 to lock
onto incoming clock phase as well. The CLKOUT signal
can be connected to the MODE_PLLIN pin of the following
stage to line up both the frequency and the phase of the
entire system. Tying the PHASMD pin to INTVCC, SGND, or
floating generates a phase difference (between
MODE_PLLIN and CLKOUT) of 120 degrees, 60 degrees,
or 90 degrees respectively. A total of 12 phases can be
cascaded to run simultaneously with respect to each other
by programming the PHASMD pin of each LTM4650-1
channel to different levels. Figure 5 shows a 2-phase
design, 4-phase design and a 6-phase design example
for clock phasing with the PHASMD table.
14
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
A multiphase power supply significantly reduces the
amount of ripple current in both the input and output capacitors. The RMS input ripple current is reduced by, and
the effective ripple frequency is multiplied by, the number
of phases used (assuming that the input voltage is greater
than the number of phases used times the output voltage).
The output ripple amplitude is also reduced by the number
of phases used when all of the outputs are tied together
to achieve a single high output current design.
In multi LTM4650-1s parallel applications, CTH and RTH
values in Table 4 are still valid to achieve a ±3% transient
response in a 25% load step. Connect one set of RC (RTH and
CTH) network to the COMP pin of each paralleling module
like a dual phase single output setup. Then connect the
COMP pins, FB pins, TRACK/SS pin and VOUT pins from
different modules together. See Figure 29 for an example
of parallel operation. LTpowerCAD Power Design Tool can
also be used to optimize loop compensation and transient
performance if only one set of RC (RTH and CTH) network
is to be added to the common COMP pins.
The LTM4650-1 device is an inherently current mode
controlled device, so parallel modules will have very good
current sharing. This will balance the thermals on the
design. Figure 29 shows an example of parallel operation
and pin connection.
Input RMS Ripple Current Cancellation
Application Note 77 provides a detailed explanation of
multiphase operation. The input RMS ripple current cancellation mathematical derivations are presented, and a graph
is displayed representing the RMS ripple current reduction
as a function of the number of interleaved phases. Figure 6
shows this graph.
Frequency Selection and Phase-Lock Loop
(MODE_PLLIN and fSET Pins)
The LTM4650-1 device is operated over a range of frequencies to improve power conversion efficiency. It is
recommended to operate the module at 400kHz for output
voltage below 1.0V, 500kHz for output voltage between
1.0V to 1.5V and 600kHz for output voltage above 1.5V,
for the best efficiency and inductor current ripple.
The LTM4650-1 switching frequency can be set with an
external resistor from the fSET pin to SGND. An accurate
10µA current source into the resistor will set a voltage
that programs the frequency or a DC voltage can be
applied. Figure 7 shows a graph of frequency setting
verses programming voltage. An external clock can be
applied to the MODE_PLLIN pin from 0V to INTVCC over
a frequency range of 400kHz to 780kHz. The clock input
high threshold is 1.6V and the clock input low threshold
is 1V. The LTM4650-1 has the PLL loop filter components
on board. The frequency setting resistor should always
be present to set the initial switching frequency before
locking to an external clock. Both regulators will operate
in continuous mode while being externally clock.
The output of the PLL phase detector has a pair of complementary current sources that charge and discharge the
internal filter network. When the external clock is applied
then the fSET frequency resistor is disconnected with
an internal switch, and the current sources control the
frequency adjustment to lock to the incoming external
clock. When no external clock is applied, then the internal
switch is on, thus connecting the external fSET frequency
set resistor for free run operation.
46501fc
For more information www.linear.com/LTM4650-1
15
LTM4650-1
Applications Information
0.60
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
0.55
0.50
RMS INPUT RIPPLE CURRENT
DC LOAD CURRENT
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
0.1 0.15
0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9
DUTY FACTOR (VOUT/VIN)
46501 F06
Figure 6. Input RMS Current Ratios to DC Load Current as a Function of Duty Cycle
900
800
FREQUENCY (kHz)
700
600
500
400
300
200
100
0
0
0.5
1
1.5
fSET PIN VOLTAGE (V)
2
2.5
46501 F07
Figure 7. Operating Frequency vs fSET Pin Voltage
16
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
Minimum On-Time
Output Voltage Tracking
Minimum on-time tON is the smallest time duration that the
LTM4650-1 is capable of turning on the top MOSFET on
either channel. It is determined by internal timing delays,
and the gate charge required turning on the top MOSFET.
Low duty cycle applications may approach this minimum
on-time limit and care should be taken to ensure that:
Output voltage tracking can be programmed externally
using the TRACK pins. The output can be tracked up
and down with another regulator. The master regulator’s
output is divided down with an external resistor divider
that is the same as the slave regulator’s feedback divider
to implement coincident tracking. The LTM4650-1 uses
an accurate 60.4k resistor internally for the top feedback
resistor for each channel. Figure 8 shows an example of
coincident tracking. Equations:
VOUT
> tON(MIN)
VIN • FREQ
If the duty cycle falls below what can be accommodated
by the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the output ripple and current will increase. The on-time
can be increased by lowering the switching frequency. A
good rule of thumb is to keep on-time longer than 110ns.
⎛ 60.4k ⎞
SLAVE = ⎜1+
⎟ • VTRACK
RTA ⎠
⎝
VTRACK is the track ramp applied to the slave’s track pin.
VTRACK has a control range of 0V to 0.6V, or the internal
reference voltage. When the master’s output is divided
down with the same resistor values used to set the slave’s
INTVCC
C10
4.7µF
R2
10k
PGOOD
MODE_PLLIN CLKOUT INTVCC EXTVCC PGOOD1
4V TO 15V INTERMEDIATE BUS
C4
22µF
25V
C3
22µF
25V
C2
22µF
25V
C1
22µF
25V
R6
100k
VIN
VOUT1
VOUTS1
SW1
TEMP
RUN1
LTM4650-1
TRACK1
VFB2
4.02k
RTA
60.4k
2200pF
VOUTS2
1.5V
VOUT2
f SET
R4
121k
RFB
60.4k
COMP1
COMP2
TRACK2
RTB
60.4k
PGOOD2
GND
DIFFP
DIFFN DIFFOUT
40.2k
4.02k
2200pF
SLAVE
SW2 PGOOD
PHASMD
SGND
VOUT1
(MASTER)
1.5V AT 25A
VFB1
RUN2
MASTER
CSS
0.1µF
C8
470µF
6.3V
C6
100µF
6.3V
C5
100µF
6.3V
C7
470µF
6.3V
VOUT2
(SLAVE)
1.2V AT 25A
INTVCC
R9
10k
RAMP TIME
tSOFTSTART = (CSS /1.3µA) • 0.6
46501 F08
Figure 8. Example of Output Tracking Application Circuit
46501fc
For more information www.linear.com/LTM4650-1
17
LTM4650-1
Applications Information
output, then the slave will coincident track with the master
until it reaches its final value. The master will continue to
its final value from the slave’s regulation point. Voltage
tracking is disabled when VTRACK is more than 0.6V. RTA
in Figure 8 will be equal to the RFB for coincident tracking.
Figure 9 shows the coincident tracking waveforms.
OUTPUT VOLTAGE
MASTER OUTPUT
SLAVE OUTPUT
46501 F09
Figure 9. Output Coincident Tracking Waveform
The TRACK pin of the master can be controlled by a
capacitor placed on the master regulator TRACK pin to
ground. A 1.3µA current source will charge the TRACK
pin up to the reference voltage and then proceed up
to INTVCC. After the 0.6V ramp, the TRACK pin will no
longer be in control, and the internal voltage reference
will control output regulation from the feedback divider.
Foldback current limit is disabled during this sequence
of turn-on during tracking or soft-starting. The TRACK
pins are pulled low when the RUN pin is below 1.2V. The
total soft-start time can be calculated as:
⎛ C ⎞
= ⎜ SS ⎟ • 0.6
⎝ 1.3µA ⎠
Regardless of the mode selected by the MODE_PLLIN pin,
the regulator channels will always start in pulse-skipping
mode up to TRACK = 0.5V. Between TRACK = 0.5V and
0.54V, it will operate in forced continuous mode and revert
to the selected mode once TRACK > 0.54V. In order to
track with another channel once in steady state operation,
the LTM4650-1 is forced into continuous mode operation
18
Ratiometric tracking can be achieved by a few simple calculations and the slew rate value applied to the master’s
TRACK pin. As mentioned above, the TRACK pin has a
control range from 0 to 0.6V. The master’s TRACK pin
slew rate is directly equal to the master’s output slew rate
in Volts/Time. The equation:
MR
• 60.4k = RTB
SR
where MR is the master’s output slew rate and SR is the
slave’s output slew rate in Volts/Time. When coincident
tracking is desired, then MR and SR are equal, thus RTB
is equal the 60.4k. RTA is derived from equation:
RTA =
TIME
tSOFT-START
as soon as VFB is below 0.54V regardless of the setting
on the MODE_PLLIN pin.
0.6V
V
V
VFB
+ FB − TRACK
60.4k RFB
RTB
where VFB is the feedback voltage reference of the regulator, and VTRACK is 0.6V. Since RTB is equal to the 60.4k
top feedback resistor of the slave regulator in equal slew
rate or coincident tracking, then RTA is equal to RFB with
VFB = VTRACK. Therefore RTB = 60.4k, and RTA = 60.4k in
Figure 8.
In ratiometric tracking, a different slew rate maybe desired
for the slave regulator. RTB can be solved for when SR
is slower than MR. Make sure that the slave supply slew
rate is chosen to be fast enough so that the slave output
voltage will reach it final value before the master output.
For example, MR = 1.5V/1ms, and SR = 1.2V/1ms. Then
RTB = 76.8k. Solve for RTA to equal to 49.9k.
Each of the TRACK pins will have the 1.3µA current source
on when a resistive divider is used to implement tracking
on that specific channel. This will impose an offset on the
TRACK pin input. Smaller values resistors with the same
ratios as the resistor values calculated from the above
equation can be used. For example, where the 60.4k is
used then a 6.04k can be used to reduce the TRACK pin
offset to a negligible value.
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
Power Good
The PGOOD pins are open drain pins that can be used to
monitor valid output voltage regulation. This pin monitors
a 10% window around the regulation point. A resistor can
be pulled up to a particular supply voltage no greater than
6V maximum for monitoring.
Stability Compensation
The LTM4650-1 has a built-in 10pF high frequency filter
capacitor from COMP to SGND on each output channel. An
external RC filtering circuit is required to add from COMP
to SGND to achieve fast Type II control loop compensation.
Table 4 is provided for most application requirements. The
Linear Technology µModule Power Design Tool (LTpowerCAD) will be provided for other control loop optimization.
Run Enable
The RUN pins have an enable threshold of 1.4V maximum,
typically 1.25V with 150mV of hysteresis. They control the
turn on each of the channels and INTVCC. These pins can be
pulled up to VIN for 5V operation, or a 5V Zener diode can be
placed on the pins and a 10k to 100k resistor can be placed
up to higher than 5V input for enabling the channels. The
RUN pins can also be used for output voltage sequencing.
In parallel operation the RUN pins can be tie together and
controlled from a single control. See the Typical Application circuits in Figure 24.
INTVCC and EXTVCC
The LTM4650-1 module has an internal 5V low dropout
regulator that is derived from the input voltage. This regulator is used to power the control circuitry and the power
MOSFET drivers. This regulator can source up to 70mA,
and typically uses ~30mA for powering the device at the
maximum frequency. This internal 5V supply is enabled
by either RUN1 or RUN2.
EXTVCC allows an external 5V supply to power the
LTM4650-1 and reduce power dissipation from the internal
low dropout 5V regulator. The power loss savings can be
calculated by:
(VIN – 5V) • 30mA = PLOSS
EXTVCC has a threshold of 4.7V for activation, and a
maximum rating of 6V. When using a 5V input, connect
this 5V input to EXTVCC also to maintain a 5V gate drive
level. EXTVCC must sequence on after VIN, and EXTVCC
must sequence off before VIN.
Differential Remote Sense Amplifier
An accurate differential remote sense amplifier is provided
to sense low output voltages accurately at the remote
load points. This is especially true for high current loads.
The amplifier can be used on one of the two channels, or
on a single parallel output. It is very important that the
DIFFP and DIFFN are connected properly at the output,
and DIFFOUT is connected to either VOUTS1 or VOUTS2.
In parallel operation, the DIFFP and DIFFN are connected
properly at the output, and DIFFOUT is connected to
one of the VOUTS pins. Review the parallel schematics in
Figure 25 and review Figure 4.
SW Pins
The SW pins are generally for testing purposes by monitoring these pins. These pins can also be used to dampen
out switch node ringing caused by LC parasitic in the
switched current paths. Usually a series R-C combination is used called a snubber circuit. The resistor will
dampen the resonance and the capacitor is chosen to
only affect the high frequency ringing across the resistor.
If the stray inductance or capacitance can be measured or
approximated then a somewhat analytical technique can
be used to select the snubber values. The inductance is
usually easier to predict. It combines the power path board
inductance in combination with the MOSFET interconnect
bond wire inductance.
First the SW pin can be monitored with a wide bandwidth
scope with a high frequency scope probe. The ring frequency can be measured for its value. The impedance Z
can be calculated:
ZL = 2πfL,
where f is the resonant frequency of the ring, and L is the
total parasitic inductance in the switch path. If a resistor
is selected that is equal to Z, then the ringing should be
dampened. The snubber capacitor value is chosen so that
46501fc
For more information www.linear.com/LTM4650-1
19
LTM4650-1
Applications Information
Temperature Monitoring
Measuring the absolute temperature of a diode is possible due to the relationship between current, voltage
and temperature described by the classic diode equation:
⎛ V ⎞
ID =IS • e ⎜ D ⎟
⎝ η• VT ⎠
or
I
VD = η• VT •In D
IS
where ID is the diode current, VD is the diode voltage, η
is the ideality factor (typically close to 1.0) and IS (saturation current) is a process dependent parameter. VT can
be broken out to:
VT =
k•T
q
where T is the diode junction temperature in Kelvin, q is
the electron charge and k is Boltzmann’s constant. VT is
approximately 26mV at room temperature (298K) and
scales linearly with Kelvin temperature. It is this linear
temperature relationship that makes diodes suitable temperature sensors. The IS term in the previous equation is
the extrapolated current through a diode junction when
the diode has zero volts across the terminals. The IS term
varies from process to process, varies with temperature,
20
and by definition must always be less than ID. Combining
all of the constants into one term:
KD =
η•k
q
where KD = 8.62 • 10−5, and knowing ln(ID/IS) is always
positive because ID is always greater than IS, leaves us
with the equation that:
I
VD = T (KELVIN) •KD •In D
IS
where VD appears to increase with temperature. It is common knowledge that a silicon diode biased with a current
source has an approximate –2mV/°C temperature relationship (Figure 10), which is at odds with the equation. In
fact, the IS term increases with temperature, reducing the
ln(ID/IS) absolute value yielding an approximate –2mV/°C
composite diode voltage slope.
0.8
0.7
DIODE VOLTAGE (V)
its impedance is equal to the resistor at the ring frequency.
Calculated by: ZC = 1/(2πfC). These values are a good place
to start with. Modification to these components should
be made to attenuate the ringing with the least amount
of power loss.
0.6
0.5
0.4
0.3
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
125
46501 F10
Figure 10. Diode Voltage VD vs Temperature T(°C)
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
To obtain a linear voltage proportional to temperature
we cancel the IS variable in the natural logarithm term to
remove the IS dependency from the equation 1. This is
accomplished by measuring the diode voltage at two currents I1, and I2, where I1 = 10 • I2) and subtracting we get:
I
I
ΔVD = T(KELVIN)•KD •IN 1 – T(KELVIN)•KD •IN 2
IS
IS
Combining like terms, then simplifying the natural log
terms yields:
∆VD = T(KELVIN) • KD • lN(10)
and redefining constant
K'D =KD •IN(10) =
198µV
K
yields
∆VD = K'D • T(KELVIN)
Solving for temperature:
T(KELVIN)=
ΔVD
(°CELSIUS)= T(KELVIN)– 273.15
K'D
where
300°K = 27°C
means that is we take the difference in voltage across the
diode measured at two currents with a ratio of 10, the
resulting voltage is 198μV per Kelvin of the junction with
a zero intercept at 0 Kelvin.
The diode connected PNP transistor at the TEMP pin
can be used to monitor the internal temperature of the
LTM4650-1. See Figure 25 for an example.
Thermal Considerations and Output Current Derating
The thermal resistances reported in the Pin Configuration
section of the data sheet are consistent with those parameters defined by JESD51-9 and are intended for use with
finite element analysis (FEA) software modeling tools that
leverage the outcome of thermal modeling, simulation,
and correlation to hardware evaluation performed on a
µModule package mounted to a hardware test board—also
defined by JESD51-9 (“Test Boards for Area Array Surface
Mount Package Thermal Measurements”). The motivation
for providing these thermal coefficients is found in JESD
51-12 (“Guidelines for Reporting and Using Electronic
Package Thermal Information”).
Many designers may opt to use laboratory equipment
and a test vehicle such as the demo board to anticipate
the µModule regulator’s thermal performance in their application at various electrical and environmental operating
conditions to compliment any FEA activities. Without FEA
software, the thermal resistances reported in the Pin Configuration section are in-and-of themselves not relevant to
providing guidance of thermal performance; instead, the
derating curves provided in the data sheet can be used in
a manner that yields insight and guidance pertaining to
one’s application-usage, and can be adapted to correlate
thermal performance to one’s own application.
The Pin Configuration section typically gives four thermal
coefficients explicitly defined in JESD 51-12; these coefficients are quoted or paraphrased below:
1. θJA, the thermal resistance from junction to ambient, is
the natural convection junction-to-ambient air thermal
resistance measured in a one cubic foot sealed enclosure. This environment is sometimes referred to as “still
air” although natural convection causes the air to move.
This value is determined with the part mounted to a
JESD 51-9 defined test board, which does not reflect
an actual application or viable operating condition.
2. θJCbottom, the thermal resistance from junction to the
bottom of the product case, is the junction-to-board
thermal resistance with all of the component power
dissipation flowing through the bottom of the package.
In the typical µModule, the bulk of the heat flows out
the bottom of the package, but there is always heat
flow out into the ambient environment. As a result, this
thermal resistance value may be useful for comparing
packages but the test conditions don’t generally match
the user’s application.
46501fc
For more information www.linear.com/LTM4650-1
21
LTM4650-1
Applications Information
3. θJCTOP, the thermal resistance from junction to top of
the product case, is determined with nearly all of the
component power dissipation flowing through the top
of the package. As the electrical connections of the
typical µModule are on the bottom of the package, it
is rare for an application to operate such that most of
the heat flows from the junction to the top of the part.
As in the case of θJCBOTTOM, this value may be useful
for comparing packages but the test conditions don’t
generally match the user’s application.
4. θJB, the thermal resistance from junction to the printed
circuit board, is the junction-to-board thermal resistance
where almost all of the heat flows through the bottom of
the µModule and into the board, and is really the sum of
the θJCbottom and the thermal resistance of the bottom
of the part through the solder joints and through a portion of the board. The board temperature is measured a
specified distance from the package, using a two sided,
two layer board. This board is described in JESD 51-9.
A graphical representation of the aforementioned thermal
resistances is given in Figure 11; blue resistances are
contained within the µModule regulator, whereas green
resistances are external to the µModule.
As a practical matter, it should be clear to the reader that
no individual or sub-group of the four thermal resistance
parameters defined by JESD 51-12 or provided in the
Pin Configuration section replicates or conveys normal
operating conditions of a µModule. For example, in normal
board-mounted applications, never does 100% of the
device’s total power loss (heat) thermally conduct exclusively through the top or exclusively through bottom of the
µModule—as the standard defines for θJCtop and θJCbottom,
respectively. In practice, power loss is thermally dissipated
in both directions away from the package—granted, in the
absence of a heat sink and airflow, a majority of the heat
flow is into the board.
Within a SIP (system-in-package) module, be aware there
are multiple power devices and components dissipating
power, with a consequence that the thermal resistances
relative to different junctions of components or die are not
exactly linear with respect to total package power loss. To
reconcile this complication without sacrificing modeling
simplicity—but also, not ignoring practical realities—an
approach has been taken using FEA software modeling
along with laboratory testing in a controlled-environment
chamber to reasonably define and correlate the thermal
resistance values supplied in this data sheet: (1) Initially,
FEA software is used to accurately build the mechanical
geometry of the µModule and the specified PCB with all
of the correct material coefficients along with accurate
power loss source definitions; (2) this model simulates
a software-defined JEDEC environment consistent with
JSED51-9 to predict power loss heat flow and temperature
readings at different interfaces that enable the calculation of
the JEDEC-defined thermal resistance values; (3) the model
JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD)
JUNCTION-TO-CASE (TOP)
RESISTANCE
CASE (TOP)-TO-AMBIENT
RESISTANCE
JUNCTION-TO-BOARD RESISTANCE
JUNCTION
JUNCTION-TO-CASE
CASE (BOTTOM)-TO-BOARD
(BOTTOM) RESISTANCE
RESISTANCE
AMBIENT
BOARD-TO-AMBIENT
RESISTANCE
46501 F11
µMODULE DEVICE
Figure 11. Graphical Representation of JESD51-12 Thermal Coefficients
22
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
and FEA software is used to evaluate the µModule with
heat sink and airflow; (4) having solved for and analyzed
these thermal resistance values and simulated various
operating conditions in the software model, a thorough
laboratory evaluation replicates the simulated conditions
with thermocouples within a controlled-environment
chamber while operating the device at the same power loss
as that which was simulated. An outcome of this process
and due-diligence yields a set of derating curves provided
in other sections of this data sheet. After these laboratory
test have been performed and correlated to the µModule
model, then the θJB and θBA are summed together to correlate quite well with the µModule model with no airflow or
heat sinking in a properly define chamber. This θJB + θBA
value is shown in the Pin Configuration section and should
accurately equal the θJA value because approximately
100% of power loss flows from the junction through the
board into ambient with no airflow or top mounted heat
sink. Each system has its own thermal characteristics,
therefore thermal analysis must be performed by the user
in a particular system.
The LTM4650-1 module has been designed to effectively
remove heat from both the top and bottom of the package. The bottom substrate material has very low thermal
resistance to the printed circuit board. An external heat
sink can be applied to the top of the device for excellent
heat sinking with airflow.
Figure 12 shows a temperature plot of the LTM4650-1
with 12V input, 1.0V output at 50A without heat sink and
a no airflow condition.
Safety Considerations
The LTM4650-1 modules do not provide isolation from
VIN to VOUT. There is no internal fuse. If required, a slow
blow fuse with a rating twice the maximum input current
needs to be provided to protect each unit from catastrophic
failure. The device does support over current protection.
A temperature diode is provided for monitoring internal
temperature, and can be used to detect the need for thermal
shutdown that can be done by controlling the RUN pin.
Figure 12. Thermal Image 12V to 1V, 50A with No Air Flow and No Heat Sink (Based on 4-Layer
101mm × 114mm PCB Board Containing 2oz Copper on the Top, Bottom and All Internal Layers)
46501fc
For more information www.linear.com/LTM4650-1
23
LTM4650-1
Applications Information
Power Derating
The 0.9V and 1.5V power loss curves in Figure 14 and
Figure 15 can be used in coordination with the load current
derating curves in Figure 16 to Figure 23 for calculating
an approximate θJA thermal resistance for the LTM46501 with various heat sinking and airflow conditions. The
power loss curves are taken at room temperature, and
are increased with a 1.2 multiplicative factor at 120°C.
The derating curves are plotted with CH1 and CH2 in
parallel single output operation starting at 50A of load
with low ambient temperature. The output voltages are
0.9V and 1.5V. These are chosen to include the lower and
higher output voltage ranges for correlating the thermal
resistance. Thermal models are derived from several
temperature measurements in a controlled temperature
chamber along with thermal modeling analysis.
The junction temperatures are monitored while ambient
temperature is increased with and without airflow. The
power loss increase with ambient temperature change
is factored into the derating curves. The junctions are
maintained at ~120°C maximum while lowering output
current or power while increasing ambient temperature.
The decreased output current will decrease the internal
module loss as ambient temperature is increased.
24
The monitored junction temperature of 120°C minus
the ambient operating temperature specifies how much
module temperature rise can be allowed. As an example in
Figure 17, the load current is derated to ~35A at ~90°C
with 200LFM air but not heat sink and the power loss for
the 12V to 0.9V at 35A output is a ~5.6W loss. The 5.6W
loss is calculated with the ~4.7W room temperature loss
from the 12V to 0.9V power loss curve at 35A, and the 1.20
multiplying factor at 120°C junction temperature. If the
90°C ambient temperature is subtracted from the 120°C
junction temperature, then the difference of 30°C divided
5.5W equals a 5.4°C/W θJA thermal resistance. Table 2
specifies a 5.5°C/W value which is pretty close. Tables 2
and 3 provide equivalent thermal resistances for 0.9V and
1.5V outputs with and without airflow and heat sinking.
The derived thermal resistances in Tables 2 and 3 for the
various conditions can be multiplied by the calculated
power loss as a function of ambient temperature to derive
temperature rise above ambient, thus maximum junction
temperature. Room temperature power loss can be derived
from the efficiency curves and adjusted with the above
ambient temperature multiplicative factors. The printed
circuit board is a 1.6mm thick 4-layer board with 2oz copper
on each layer. The PCB dimensions are 101mm × 114mm.
The BGA heat sinks are listed in Table 3.
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
Layout Checklist/Example
• Do not put via directly on the pad, unless they are
capped or plated over.
The high integration of LTM4650-1 makes the PCB board
layout very simple and easy. However, to optimize its
electrical and thermal performance, some layout considerations are still necessary.
• Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND
to GND underneath the unit.
• For parallel modules, tie the VOUT, VFB, and COMP pins
together. Use an internal layer to closely connect these
pins together. The TRACK pin can be tied a common
capacitor for regulator soft-start.
• Use large PCB copper areas for high current paths,
including VIN, GND, VOUT1 and VOUT2. It helps to minimize the PCB conduction loss and thermal stress.
• Place high frequency ceramic input and output capacitors next to the VIN, PGND and VOUT pins to minimize
high frequency noise.
• Bring out test points on the signal pins for monitoring.
Figure 13 gives a good example of the recommended
layout. LGA and BGA PCB layouts are identical with the
exception of circle pads for BGA (see Package Description).
• Place a dedicated power ground layer underneath
the unit.
• To minimize the via conduction loss and reduce module
thermal stress, use multiple vias for interconnection
between top layer and other power layers.
CIN1
CIN2
VIN
M
L
K
GND
GND
J
H
G
COUT1
SGND
F
COUT2
E
D
C
B
A
1
2
3
4
5
VOUT1
6
7
8
9
10
11
12
GND
VOUT2
46501 F13
CNTRL
CNTRL
Figure 13. Recommended PCB Layout
46501fc
For more information www.linear.com/LTM4650-1
25
LTM4650-1
Applications Information
Table 2. 0.9V Output
DERATING CURVE
Figures 16, 17
Figures 16, 17
Figures 16, 17
Figures 18, 19
Figures 18, 19
Figures 18, 19
VIN (V)
5, 12
5, 12
5, 12
5, 12
5, 12
5, 12
POWER LOSS CURVE
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
AIRFLOW (LFM)
0
200
400
0
200
400
HEAT SINK
None
None
None
BGA Heat Sink
BGA Heat Sink
BGA Heat Sink
θJA (°C/W)
7.5
5.5
5
7
4.5
4
VIN (V)
5, 12
5, 12
5, 12
5, 12
5, 12
5, 12
POWER LOSS CURVE
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
AIRFLOW (LFM)
0
200
400
0
200
400
HEAT SINK
None
None
None
BGA Heat Sink
BGA Heat Sink
BGA Heat Sink
θJA (°C/W)
7.5
5.5
5
7
4.5
4
Table 3. 1.5V Output
DERATING CURVE
Figures 20, 21
Figures 20, 21
Figures 20, 21
Figures 22, 23
Figures 22, 23
Figures 22, 23
HEAT SINK MANUFACTURER
PART NUMBER
WEBSITE
Wakefield
LTN20069-T5
wakefield-vette.com
Table 4. Output Voltage Response vs Component Matrix (Refer to Figure 23) Load Step Typical Measured Values
2-Phase Single Output Solution
CIN (CERAMIC)
COUT (CERAMIC)
VENDORS
VALUE
VENDORS
VALUE
PART NUMBER
Murata
22µF, 16V,
X5R, 1210
GRM32ER61C226KE20L Murata
100µF, 6.3V, GRM32ER60J107ME20L
X5R, 1210
Panasonic 680µF,
2R5TPF680M6L
2.5V, 6mΩ
Murata
22µF, 16V,
X5R, 1206
GRM31CR61C226KE15K Murata
220µF, 4V,
X5R, 1206
Panasonic 470µF
EEFGX0E471R
2.5V, 3mΩ
TDK
22µF, 16V,
X5R, 1210
C3225X5R1C226M250AA Taiyo Yuden 100µF, 6.3V, JMK325BJ107MM-T
X5R, 1210
Taiyo Yuden 220µF, 4V,
X5R, 1210
26
PART NUMBER
COUT (BULK)
GRM31CR60G227M
VENDORS VALUE
PART NUMBER
AMK325ABJ227MM-T
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Applications Information
25% Load Step (0A to 12.5A) Ceramic Output Capacitor Only Solutions
CTRL
CTRL
FEEDPEAKLOAD
COMP PIN
LOOP LOOP
PEAK
SETTLING BAND- PHASE LOAD STEP
PARALLEL COMP PIN COMP PIN FORWARD
COUT
CAPACITOR RESISTOR CAPACITOR CAPACITOR DEVIATION TIME
WIDTH MARGIN STEP SLEW RFB FREQ
(CTH)
(CFF)
(VPK-PK) (tSETTLE) (BW)
(A)
RATE (kΩ) (kHz)
(CERAMIC) (CTHP)
(RTH)
(PM)
PEAK-PEAK
DEVIATION
PERCENTAGE
CIN*
CIN
VIN VOUT (BULK) (CERAMIC)
±3% (<60mV)
12V
150µF
22µF x 2
None
220µF x 6
33pF
3.24kΩ
10nF
68pF
53mV
80µs
88kHz
47 Deg
12.5 10A/µs 90.9
500
±3% (<72mV)
12V 1.2V 150µF
22µF x 2
None
220µF x 5
33pF
3.24kΩ
10nF
68pF
56mV
80µs
89kHz
49 Deg
12.5 10A/µs 60.4
500
±3% (<90mV)
12V 1.5V 150µF
22µF x 2
None
220µF x 4
33pF
3.24kΩ
10nF
68pF
58mV
80µs
91kHz
58 Deg
12.5 10A/µs 40.2
600
±3% (<108mV) 12V 1.8V 150µF
22µF x 2
None
220µF x 4
33pF
3.24kΩ
10nF
68pF
64mV
90µs
98kHz
65 Deg
12.5 10A/µs 30.2
600
1V
COUT
(BULK)
25% Load Step (0A to 9A) Bulk + Ceramic Output Capacitor Solutions
CTRL
CTRL
FEEDPEAKLOAD
COMP PIN
COMP
LOOP LOOP
COMP PIN FORWARD
PEAK
SETTLING BAND- PHASE LOAD STEP
PARALLEL
PIN
COUT
CAPACITOR RESISTOR CAPACITOR CAPACITOR DEVIATION TIME
WIDTH MARGIN STEP SLEW RFB FREQ
(CTH)
(CFF)
(VPK-PK) (tSETTLE) (BW)
(A)
RATE (kΩ) (kHz)
(CERAMIC) (CTHP)
(RTH)
(PM)
PEAK-PEAK
DEVIATION
PERCENTAGE
CIN*
CIN
VIN VOUT (BULK) (CERAMIC)
±3% (<60mV)
12V
150µF
22µF × 2
470µF × 2 100µF × 4
33pF
3.16kΩ
3300pF
68pF
55mV
30µs
82kHz
68 Deg
12.5 10A/µs 90.9
500
±3% (<72mV)
12V 1.2V 150µF
22µF × 2
470µF × 2 100µF × 4
33pF
3.16kΩ
3300pF
68pF
55mV
30µs
82kHz
73 Deg
12.5 10A/µs 60.4
500
±3% (<90mV)
12V 1.5V 150µF
22µF × 2
470µF × 2 100µF × 4
82pF
4.12kΩ
3300pF
None
64mV
30µs
59kHz
53 Deg
12.5 10A/µs 40.2
600
±3% (<108mV) 12V 1.8V 150µF
22µF × 2
470µF × 2 100µF × 4
82pF
4.12kΩ
3300pF
None
75mV
30µs
51kHz
58 Deg
12.5 10A/µs 30.2
600
1V
COUT
(BULK)
50% Load Step (0A to 25A) Ceramic Output Capacitor Only Solutions
CTRL
CTRL
FEEDPEAKLOAD
COMP PIN
LOOP LOOP
PEAK
SETTLING BAND- PHASE LOAD STEP
PARALLEL COMP PIN COMP PIN FORWARD
COUT
CAPACITOR RESISTOR CAPACITOR CAPACITOR DEVIATION TIME
WIDTH MARGIN STEP SLEW RFB FREQ
(CTH)
(CFF)
(VPK-PK) (tSETTLE) (BW)
(A)
RATE (kΩ) (kHz)
(CERAMIC) (CTHP)
(RTH)
(PM)
PEAK-PEAK
DEVIATION
PERCENTAGE
CIN*
CIN
VIN VOUT (BULK) (CERAMIC)
±3% (<60mV)
12V
150µF
22µF × 2
None
220µF × 12
33pF
6.81kΩ
4.7nF
100pF
58mV
80µs
76kHz
45 Deg
25
10A/µs 90.9
500
±3% (<72mV)
12V 1.2V 150µF
22µF × 2
None
220µF × 12
33pF
6.81kΩ
4.7nF
100pF
61mV
80µs
77kHz
50 Deg
25
10A/µs 60.4
500
±3% (<90mV)
12V 1.5V 150µF
22µF × 2
None
220µF × 14
33pF
5.90kΩ
4.7nF
None
90mV
80µs
47kHz
45 Deg
25
10A/µs 40.2
600
±3% (<108mV) 12V 1.8V 150µF
22µF × 2
None
220µF × 14
33pF
5.90kΩ
4.7nF
None
105mV
90µs
43kHz
50 Deg
25
10A/µs 30.2
600
1V
COUT
(BULK)
50% Load Step (0A to 25A) Bulk + Ceramic Output Capacitor Solutions
CTRL
CTRL
FEEDPEAKLOAD
COMP PIN
COMP
LOOP LOOP
COMP PIN FORWARD
PEAK
SETTLING BAND- PHASE LOAD STEP
PARALLEL
PIN
COUT
CAPACITOR RESISTOR CAPACITOR CAPACITOR DEVIATION TIME
WIDTH MARGIN STEP SLEW RFB FREQ
(CTH)
(CFF)
(VPK-PK) (tSETTLE) (BW)
(A)
RATE (kΩ) (kHz)
(CERAMIC) (CTHP)
(RTH)
(PM)
PEAK-PEAK
DEVIATION
PERCENTAGE
CIN*
CIN
VIN VOUT (BULK) (CERAMIC)
±3% (<60mV)
12V
150µF
22µF × 2
470µF × 6 100µF × 4
33pF
12.0kΩ
3300pF
47pF
47mV
30µs
70kHz
57 Deg
25
10A/µs 90.9
500
±3% (<72mV)
12V 1.2V 150µF
22µF × 2
470µF × 6 100µF × 4
33pF
12.0kΩ
3300pF
47pF
48mV
30µs
67kHz
65 Deg
25
10A/µs 60.4
500
±3% (<90mV)
12V 1.5V 150µF
22µF × 2
470µF × 6 100µF × 4
68pF
10.2kΩ
3300pF
None
56mV
40µs
50kHz
49 Deg
25
10A/µs 40.2
600
±3% (<108mV) 12V 1.8V 150µF
22µF × 2
470µF × 6 100µF × 4
82pF
14.5kΩ
3300pF
None
58mV
50µs
51kHz
46 Deg
25
10A/µs 30.2
600
1V
COUT
(BULK)
*Bulk input capacitor is only needed if the input source impedance is compromised by long inductive leads.
46501fc
For more information www.linear.com/LTM4650-1
27
LTM4650-1
Applications Information
8
8
7
7
6
5
4
3
5
4
3
2
1
1
0
10
30
20
LOAD CURRENT (A)
40
0
50
50
6
2
0
60
VIN = 12V
VIN = 5V
9
POWE LOSS (W)
POWE LOSS (W)
10
VIN = 12V
VIN = 5V
9
OUTPUT CURRENT (A)
10
30
20
0LFM
200LFM
400LFM
10
0
10
30
20
LOAD CURRENT (A)
40
0
50
46501 F14
25
Figure 16. 5V to 0.9V
Derating Curve, No Heat Sink
60
50
50
50
20
0LFM
200LFM
400LFM
10
0
25
35
OUTPUT CURRENT (A)
60
OUTPUT CURRENT (A)
60
30
40
30
20
0LFM
200LFM
400LFM
10
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
0
25
35
50
50
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
0
0LFM
200LFM
400LFM
25
35
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
46501 F19
Figure 19. 12V to 0.9V Derating
Curve, BGA Heat Sink
Figure 18. 5V to 0.9V Derating
Curve, BGA Heat Sink
60
40
30
20
0LFM
200LFM
400LFM
35
20
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
60
25
30
46501 F18
Figure 17. 12V to 0.9V
Derating Curve, No Heat Sink
0
40
10
46501 F17
10
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
46501 F16
Figure 15. 1.5V Output Power
Loss Curve
40
35
46501 F15
Figure 14. 0.9V Output Power
Loss Curve
OUTPUT CURRENT (A)
40
40
30
20
0LFM
200LFM
400LFM
10
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
0
25
35
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
46501 F20
Figure 20. 5V to 1.5V Derating
Curve, No Heat Sink
28
46501 F21
Figure 21. 12V to 1.5V
Derating Curve, No Heat Sink
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
60
60
50
50
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Applications Information
40
30
20
0LFM
200LFM
400LFM
10
0
25
35
40
30
20
0LFM
200LFM
400LFM
10
0
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
25
35
45 55 65 75 85 95 105 115
AMBIENT TEMPERATURE (°C)
46501 F22
46501 F23
Figure 22. 5V to 1.5V Derating
Curve, BGA Heat Sink
Figure 23. 12V to 1.5V
Derating Curve, BGA Heat Sink
INTVCC
INTVCC
C10
4.7µF
R2
10k
PGOOD1
VIN
4.5V TO 15V
MODE_PLLIN CLKOUT INTVCC
+
CIN
(OPT)
C1
22µF
25V
×4
R7
100k
VOUT1
VOUTS1
TEMP
RUN1
6.49k
4700pF
4700pF
R4
121k
COMP1
COMP2
fSET
PHASMD
SGND
COUT1
100µF
6.3V
SW1
VFB1
RUN2
TRACK1
TRACK1
C5
0.1µF TRACK2 TRACK2
C9
0.1µF
6.49k
EXTVCC PGOOD1
VIN
VFB2
RFB2
60.4k
LTM4650-1
VOUT2
SW2
PGOOD2
VOUTS2
GND
DIFFN
DIFFP
INTVCC
R3
10k
VOUT1
1.5V AT 25A
+
COUT2
470µF
6.3V
RFB1
40.2k
PGOOD2
COUT3
100µF
6.3V
VOUT2
1.2V AT 25A
+
COUT4
470µF
6.3V
DIFFOUT
46501 F24
Figure 24. Typical 4.5VIN to 15VIN, 1.5V and 1.2V at 25A Outputs
46501fc
For more information www.linear.com/LTM4650-1
29
LTM4650-1
Typical Applications
INTVCC
INTVCC
C10
4.7µF
R2
10k
PGOOD
MODE_PLLIN
VIN
4.5V TO 15V
CIN
22µF
25V
×4
TRACK
RUN
CLKOUT INTVCC
EXTVCC PGOOD1
VIN
VOUT1
RUN1
VOUT2
RUN2
VOUTS1
TRACK1
SW1
TRACK2
C9
0.1µF
R5
90.9k
VFB2
LTM4650-1
COMP2
TEMP
68pF
VOUT2
VOUTS2
3.24k
10nF
VOUT
1V
50A
VFB1
COMP1
TEMP
MONITOR
33pF
COUT1
220µF
4V
×6
fSET
R4
121k
SW2
PGOOD2
PHASMD
SGND
GND
DIFFN
DIFFP
PGOOD
DIFFOUT
46501 F25
*SEE TABLE 4
Figure 25. LTM4650-1 2-Phase, 1V at 50A Design
VOUT(AC)
20mV/DIV
PHASE
GAIN (dB)
54mV
LOAD STEP
10A/DIV
50µs/DIV
46501 F26
46501 F27
Figure 26. 25%, 12.5A Load Step Transient
Waveform of Figure 23 Circuit
30
Figure 27. Bode Plot of Figure 23 Circuit
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
typical Applications
INTVCC
INTVCC
C10
4.7µF
R2
10k
PGOOD1
MODE_PLLIN CLKOUT INTVCC EXTVCC PGOOD1
VIN
4.5V TO 15V
CIN
22µF
25V
×4
VOUT1
R9
60.4k
VOUT1
1.2V
6.34k
1500pF
SW1
RUN1
VFB1
1500pF
VFB2
LTM4650-1
TRACK2
R7
90.9k
R8
90.9k
+
VOUT2
PHASMD
SGND
SW2
PGOOD2
GND
DIFFP
DIFFN
VOUT1
1.2V
COUT2 25A
470µF
6.3V
R5
60.4k
VOUTS2
COMP1
COMP2
fSET
R4
121k
COUT1
100µF
6.3V
×2
VOUTS1
TEMP
RUN2
TRACK1
C5
0.1µF
6.34k
R6
100k
VIN
INTVCC
R3
10k
PGOOD2
COUT1
100µF
6.3V
×2
+
VOUT2
1V AT 25A
COUT2
470µF
6.3V
DIFFOUT
46501 F28
Figure 28. LTM4650-1 1.2V and 1V Output Tracking
46501fc
For more information www.linear.com/LTM4650-1
31
LTM4650-1
typical applications
INTVCC
CLK1
CIN1
22µF
25V
×3
EXTVCC PGOOD1
VOUT1
VIN
R6
100k
VOUTS1
TEMP
SW1
VFB1
RUN1
RUN
RUN2
VFB2
LTM4650-1
TRACK1
TRACK
R2
5k
PGOOD
MODE_PLLIN CLKOUT INTVCC
VIN
4.5V TO 15V
INTVCC
C10
4.7µF
VFB
33pF
COMP1
VOUT2
COMP2
VOUTS2
SW2
PHASMD
3300pF
R4
121k
SGND
COUT2
470µF
6.3V
COUT1
100µF
6.3V
×2
+
COUT2
470µF
6.3V
68pF
fSET
3.16k
+
R5
60.4k
TRACK2
COMP
COUT1
100µF
6.3V
×2
PGOOD2
GND
DIFFP
DIFFN
PGOOD
DIFFOUT
VOUT
1.2V
100A
C16
4.7µF
CLK1
MODE_PLLIN CLKOUT INTVCC
CIN2
22µF
25V
×3
VOUT1
VOUTS1
TEMP
RUN
SW1
RUN1
VFB1
RUN2
TRACK
VFB
COUT1
100µF
6.3V
×2
+
COUT2
470µF
6.3V
COUT1
100µF
6.3V
×2
+
COUT2
470µF
6.3V
VFB2
LTM4650-1
TRACK1
TRACK2
C19
0.22µF
33pF
EXTVCC PGOOD1
VIN
R9
100k
PGOOD
VOUTS2
COMP2
VOUT2
SW2
fSET
3.16k
3300pF
COMP1
PHASMD
R10
121k
SGND
PGOOD2
GND
DIFFP
DIFFN
DIFFOUT
INTVCC
PGOOD
46501 F29
Figure 29. LTM4650-1 4-Phase, 1.2V at 100A
32
46501fc
For more information www.linear.com/LTM4650-1
LTM4650-1
Package Description
LTM4650-1 Component BGA Pinout
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
A1
VOUT1
B1
VOUT1
C1
VOUT1
D1
GND
E1
GND
F1
GND
A2
VOUT1
B2
VOUT1
C2
VOUT1
D2
GND
E2
GND
F2
GND
A3
VOUT1
B3
VOUT1
C3
VOUT1
D3
GND
E3
GND
F3
GND
A4
VOUT1
B4
VOUT1
C4
VOUT1
D4
GND
E4
GND
F4
MODE_PLLIN
A5
VOUT1
B5
VOUT1
C5
VOUT1S
D5
VFB1
E5
TRACK1
F5
RUN1
A6
GND
B6
GND
C6
fSET
D6
SGND
E6
COMP1
F6
SGND
A7
GND
B7
GND
C7
SGND
D7
VFB2
E7
COMP2
F7
SGND
A8
VOUT2
B8
VOUT2
C8
VOUT2S
D8
TRACK2
E8
DIFFP
F8
DIFFOUT
A9
VOUT2
B9
VOUT2
C9
VOUT2
D9
GND
E9
DIFFN
F9
RUN2
A10
VOUT2
B10
VOUT2
C10
VOUT2
D10
GND
E10
GND
F10
GND
A11
VOUT2
B11
VOUT2
C11
VOUT2
D11
GND
E11
GND
F11
GND
A12
VOUT2
B12
VOUT2
C12
VOUT2
D12
GND
E12
GND
F12
GND
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
G1
GND
H1
GND
J1
GND
K1
GND
L1
GND
M1
GND
G2
SW1
H2
GND
J2
VIN
K2
VIN
L2
VIN
M2
VIN
G3
GND
H3
GND
J3
VIN
K3
VIN
L3
VIN
M3
VIN
G4
PHASEMD
H4
GND
J4
VIN
K4
VIN
L4
VIN
M4
VIN
G5
CLKOUT
H5
GND
J5
GND
K5
GND
L5
VIN
M5
VIN
G6
SGND
H6
GND
J6
TEMP
K6
GND
L6
VIN
M6
VIN
G7
SGND
H7
GND
J7
EXTVCC
K7
GND
L7
VIN
M7
VIN
G8
PGOOD2
H8
INTVCC
J8
GND
K8
GND
L8
VIN
M8
VIN
G9
PGOOD1
H9
GND
J9
VIN
K9
VIN
L9
VIN
M9
VIN
G10
GND
H10
GND
J10
VIN
K10
VIN
L10
VIN
M10
VIN
G11
SW2
H11
GND
J11
VIN
K11
VIN
L11
VIN
M11
VIN
G12
GND
H12
GND
J12
GND
K12
GND
L12
GND
M12
GND
46501fc
For more information www.linear.com/LTM4650-1
33
aaa Z
0.630 ±0.025 Ø 144x
E
PACKAGE TOP VIEW
3.1750
3.1750
SUGGESTED PCB LAYOUT
TOP VIEW
1.9050
4
0.6350
0.0000
0.6350
PIN “A1”
CORNER
1.9050
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
www.linear.com/LTM4650-1
tion that the interconnection
of itsinformation
circuits as described
herein will not infringe on existing patent rights.
6.9850
5.7150
4.4450
3.1750
1.9050
0.6350
0.0000
0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
Y
X
D
DETAIL B
H2
MOLD
CAP
ccc Z
SYMBOL
A
A1
A2
b
b1
D
E
e
F
G
H1
H2
aaa
bbb
ccc
ddd
eee
H1
SUBSTRATE
A1
NOM
5.01
0.60
4.41
0.75
0.63
16.00
16.00
1.27
13.97
13.97
0.41
4.00
MAX
5.21
0.70
4.51
0.90
0.66
Z
NOTES
DETAIL B
PACKAGE SIDE VIEW
0.46
4.05
0.15
0.10
0.20
0.30
0.15
TOTAL NUMBER OF BALLS: 144
0.36
3.95
MIN
4.81
0.50
4.31
0.60
0.60
b1
DIMENSIONS
ddd M Z X Y
eee M Z
DETAIL A
Øb (144 PLACES)
aaa Z
A2
A
(Reference LTC DWG # 05-08-1523 Rev Ø)
// bbb Z
34
Z
BGA Package
144-Lead (16mm × 16mm × 5.01mm)
e
L
b
K
J
G
G
F
E
e
PACKAGE BOTTOM VIEW
H
D
C
B
DETAIL A
A
DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
BALL DESIGNATION PER JESD MS-028 AND JEP95
7
TRAY PIN 1
BEVEL
!
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
12
11
10
9
8
7
6
5
4
3
2
1
3
SEE NOTES
PIN 1
7
SEE NOTES
BGA 144 1215 REV Ø
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY
6. SOLDER BALL COMPOSITION IS 96.5% Sn/3.0% Ag/0.5% Cu
5. PRIMARY DATUM -Z- IS SEATING PLANE
4
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
COMPONENT
PIN “A1”
F
b
M
LTM4650-1
Package Description
Please refer to http://www.linear.com/product/LTM4650-1#packaging for the most recent package drawings.
46501fc
6.9850
5.7150
4.4450
4.4450
5.7150
6.9850
LTM4650-1
Revision History
REV
DATE
DESCRIPTION
A
05/16
Added SnPb Ball Finish
B
07/16
Added LTM4650-1A
C
12/16
PAGE NUMBER
1, 2
1, 2, 3, 4, 10
Connected COMP pin of Master and Slave devices
30
Corrected Part Marking and Finished Code
2
46501fc
For more information www.linear.com/LTM4650-1
35
LTM4650-1
Package Photo
BGA
Design Resources
SUBJECT
DESCRIPTION
µModule Design and Manufacturing Resources
Design:
• Selector Guides
• Demo Boards and Gerber Files
• Free Simulation Tools
µModule Regulator Products Search
1. Sort table of products by parameters and download the result as a spread sheet.
Manufacturing:
• Quick Start Guide
• PCB Design, Assembly and Manufacturing Guidelines
• Package and Board Level Reliability
2. Search using the Quick Power Search parametric table.
TechClip Videos
Quick videos detailing how to bench test electrical and thermal performance of µModule products.
Digital Power System Management
Linear Technology’s family of digital power supply management ICs are highly integrated solutions that
offer essential functions, including power supply monitoring, supervision, margining and sequencing,
and feature EEPROM for storing user configurations and fault logging.
Related Parts
PART NUMBER DESCRIPTION
COMMENTS
LTM4650
LTM4650-1 with Internal Compensation
4.5V ≤ VIN ≤ 15V, Dual 25A or Single 50A
LTM4630
Lower Current than LTM4650; Dual 18A or Single 36A
Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 15V, 0.6V ≤ VOUT ≤ 1.8V,
15mm × 15mm × 4.41mm LGA and 15mm × 15mm × 5.01mm BGA Packages
LTM4630A
Lower Current and Higher VOUT than LTM4650; Up to
5.3VOUT, Dual 18A or Single 26A
Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 15V, 0.6V ≤ VOUT ≤ 5.3V,
15mm × 15mm × 4.41mm LGA Package
LTM4630-1
Lower Current than LTM4650 with External Compensation Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 15V, 0.6V ≤ VOUT ≤ 1.8V,
15mm × 15mm × 5.01mm BGA Package
and ±0.8% (–1A) or ±1.5% (–1B) VOUT Accuracy
LTM4620
Lower Current than LTM4650; Dual 13A or Single 26A.
Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 16V, 0.6V ≤ VOUT ≤ 2.5V,
15mm 15mm × 4.41mm LGA and 15mm × 15mm × 5.01mm BGA Packages
LTM4620A
Lower Current and Higher VOUT than LTM4650; Up to
5.3VOUT, Dual 13A or Single 26A.
Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 16V, 0.6V ≤ VOUT ≤ 2.5V,
15mm 15mm × 4.41mm LGA and 15mm × 15mm × 5.01mm BGA Packages
LTM4628
Lower Current, Higher VIN and VOUT than LTM4650; Dual
8A or Single 16A
Pin Compatible with LTM4650; 4.5V ≤ VIN ≤ 26.5V, 0.6V ≤ VOUT ≤ 5.5V,
15mm 15mm × 4.32mm LGA and 15mm × 15mm × 4.92mm BGA Packages
LTM4677
Dual 18A or Single 36A with PSM
4.5V ≤ VIN ≤ 16V, 0.5V ≤ VOUT ≤ 1.8V. 16mm × 16mm × 5.01mm BGA Package
LTM4639
Lower VIN (2.375V ≤ VIN ≤ 7V), 20A
0.6V ≤ VOUT ≤ 5.5V. 15mm × 15mm × 4.92mm BGA Package
36 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTM4650-1
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTM4650-1
46501fc
LT 1216 REV C • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2016
Similar pages