Pan Jit GBJ8J Glass passivated single-phase bridge rectifier(voltage - 50 to 800 volts current - 8.0 amperes) Datasheet

Approve Sheet Part Number: GBJ8A~GBJ8K
DATA SHEET
GBJ8A~GBJ8K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 8.0 Amperes
GBJ
Unit: inch ( mm )
FEATURES
0.146(3.7)
0.129(3.3)
• High temperature soldering guaranteed:
0.578(14.7)
0.603(15.3)
• Surge overload rating: 200Amperes peak
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
0.115(2.9)
0.098(2.5)
0.669(17.0)
0.709(18.0)
Case: Reliable low cost construction utilizing
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
Mounting position: Any
Mounting torque: 5 in. lb. Max.
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
Weight: 0.15 ounce, 4.0 grams
0.150(3.8)
0.133(3.4)
0.382(9.7)
0.366(9.3)
• Reliable low cost construction utilizing molded plastic technique
0.122(3.1)
0.142(3.6)
• Ideal for printed circuit board
0.189(4.8)
0.173(4.4)
0.996(25.3)
0.972(24.7)
C 0.118 (3.0)
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
0.032(0.8)
0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBJ8A
GBJ8B
GBJ8D
GBJ8G
GBJ8J
GBJ8K
UNIT
Maximum Recurrent Peak Reverse Voltage
50
100
200
400
600
800
V
Maximum RMS Input Voltage
35
70
140
280
420
560
V
Maximum DC Blocking Voltage
50
100
200
400
600
800
V
Maximum Average Forward TC=100°C
8.0
TA= 45°C
6.0
Rectified Output Current
A
I2t Rating for fusing ( t<8.3ms)
166
A2sec
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
200
Apk
Maximum Instantaneous Forward Voltage Drop per element at 8.0A
1.0
Vpk
Maximum Reverse Leakage at rated TA=25°
5
CDc Blocking Voltage per element TC=100°C
500
µA
µA
Typical Thermal Resistance per leg(Note 2) RθJA
18.0
°C / W
Typical Thermal Resistance per leg(Note 3) RθJC
3.0
°C / W
-55 to +150
°C
Operating and Storage Temperature Range, TJ,TSTG
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.
PAGE . 1
Approve Sheet Part Number: GBJ8A~GBJ8K
INSTANTANEOUS FORWARD CURRENT, AMPERES
AVERAGE FORWARD CURRENT
AMPERES
8.0
HEAT-SINK
MOUNTING,TC
(4 4 0.15) INCH
COPPER PLATE
6.0
4.0
2.0
MOUNTED ON PC BOARD.
TA 0.5"(12.7mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
0
0
50
100
100
40
20
10
4.0
1.0
0.4
0.2
0.1
0.7
150
O
TEMPERATURE C
FPRWARD SURGE CURRENT, AMPERES pk
(HALF SINE-WAVE)
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
10
O
T C =100 C
1.0
0.1
O
T A =25 C
0.01
20
40
60
80
100
120
0.8
0.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
ig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT
0
TJ=25OC
Pulse Width=300 S
1% DULY Cycle
2.0
140
PERCENT OF PEAK REVERSE VOLTAGE
Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS
Fig. 2- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISITCS PER ELEMENT
200
160
120
80
O
T A =105 C
40
0
1
2
6
10
20
40
60
100
NO. OF CYCLES AT 60Hz
Fig. 4- MAXIMUM NON-REPETITEVE PEAK
FORWARD SURGE CURRENT
CAPACITANCE, pF
400
100
O
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
50
10
1
5
10
50
100
REVERSE VOLTAGE, VOLTS
Fig 5 TYPICL JUNCTION CAPACITANCE PER ELEMENT
PAGE . 2
Similar pages