LM78LXX Series 3-Terminal Positive Regulators General Description The LM78LXX series of three terminal positive regulators is available with several fixed output voltages making them useful in a wide range of applications. When used as a zener diode/resistor combination replacement, the LM78LXX usually results in an effective output impedance improvement of two orders of magnitude, and lower quiescent current. These regulators can provide local on card regulation, eliminating the distribution problems associated with single point regulation. The voltages available allow the LM78LXX to be used in logic systems, instrumentation, HiFi, and other solid state electronic equipment. The LM78LXX is available in the plastic TO-92 (Z) package, the plastic SO-8 (M) package and a chip sized package (8-Bump micro SMD) using National’s micro SMD package technology. With adequate heat sinking the regulator can deliver 100mA output current. Current limiting is included to limit the peak output current to a safe value. Safe area protection for the output transistors is provided to limit inter- nal power dissipation. If internal power dissipation becomes too high for the heat sinking provided, the thermal shutdown circuit takes over preventing the IC from overheating. Features n LM78L05 in micro SMD package n Output voltage tolerances of ± 5% over the temperature range n Output current of 100mA n Internal thermal overload protection n Output transistor safe area protection n Internal short circuit current limit n Available in plastic TO-92 and plastic SO-8 low profile packages n No external components n Output voltages of 5.0V, 6.2V, 8.2V, 9.0V, 12V, 15V n See AN-1112 for micro SMD considerations Connection Diagrams (TO-92) Plastic Package (Z) SO-8 Plastic (M) (Narrow Body) 00774403 00774402 Top View 8-Bump micro SMD Bottom View micro SMD Marking Orientation 00774424 Top View (Bump Side Down) 00774433 Top View © 2005 National Semiconductor Corporation DS007744 www.national.com LM78LXX Series 3-Terminal Positive Regulators February 2005 LM78LXX Series Ordering Information Package microSMD SOIC Narrow TO-92 www.national.com Order Number Output Voltage NSC Drawing Supplied As LM78L05IBP 5V BPA08AAB Reel of 250 LM78L05IBPX 5V BPA08AAB Reel of 3000 LM78L09ITP 9V TPA08AAA Reel of 250 LM78L09ITPX 9V TPA08AAA Reel of 3000 LM78L05ACM 5V M08A Rail of 95 LM78L05ACMX 5V M08A Reel of 2500 LM78L12ACM 12V M08A Rail of 95 LM78L12ACMX 12V M08A Reel of 2500 LM78L15ACM 15V M08A Rail of 95 LM78L15ACMX 15V M08A Reel of 2500 LM78L05ACZ 5V Z03A Box of 1800 LM78L62ACZ 6.2V Z03A Box of 1800 LM78L82ACZ 8.2V Z03A Box of 1800 LM78L09ACZ 9V Z03A Box of 1800 LM78L12ACZ 12V Z03A Box of 1800 LM78L15ACZ 15V Z03A Box of 1800 2 Operating Junction Temperature SO-8, TO-92 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Power Dissipation (Note 5) Infrared or Convection (20 sec.) 35V Storage Temperature −40˚C to 85˚C Soldering Information Internally Limited Input Voltage 0˚C to 125˚C micro SMD 235˚C Wave Soldering (10 sec.) 260˚C (lead time) −65˚C to +150˚C ESD Susceptibility (Note 2) 1kV LM78LXX Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, Bold typeface applies over 0˚C to 125˚C for SO-8 and TO-92 packages, and −40˚C to 85˚C for micro SMD package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO = 40mA, CI = 0.33µF, CO = 0.1µF. LM78L05 Unless otherwise specified, VIN = 10V Symbol VO ∆VO Parameter Conditions Output Voltage Line Regulation Min Typ Max 4.8 5 5.2 7V ≤ VIN ≤ 20V 1mA ≤ IO ≤ 40mA (Note 3) 4.75 5.25 1mA ≤ IO ≤ 70mA (Note 3) 4.75 5.25 7V ≤ VIN ≤ 20V 18 8V ≤ VIN ≤ 20V 10 54 1mA ≤ IO ≤ 100mA 20 60 5 30 mV Load Regulation IQ Quiescent Current ∆IQ Quiescent Current Change 8V ≤ VIN ≤ 20V 1.0 1mA ≤ IO ≤ 40mA 0.1 Vn Output Noise Voltage f = 10 Hz to 100 kHz (Note 4) Ripple Rejection f = 120 Hz 8V ≤ VIN ≤ 16V 3 47 Peak Output Current IPK Average Output Voltage Tempco VIN (Min) Minimum Value of Input Voltage Required to Maintain Line Regulation θJA Thermal Resistance (8-Bump micro SMD) IO = 5mA V 75 ∆VO 1mA ≤ IO ≤ 40mA Units 5 mA 40 µV 62 dB 140 mA −0.65 mV/˚C 6.7 7 V 230.9 ˚C/W LM78L62AC Unless otherwise specified, VIN = 12V Symbol VO Parameter Conditions Output Voltage Min Typ Max 5.95 6.2 6.45 8.5V ≤ VIN ≤ 20V 1mA ≤ IO ≤ 40mA (Note 3) 5.9 6.5 1mA ≤ IO ≤ 70mA (Note 3) 5.9 6.5 3 Units V www.national.com LM78LXX Series Absolute Maximum Ratings (Note 1) LM78LXX Series LM78LXX Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, Bold typeface applies over 0˚C to 125˚C for SO-8 and TO-92 packages, and −40˚C to 85˚C for micro SMD package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO = 40mA, CI = 0.33µF, CO = 0.1µF. (Continued) LM78L62AC (Continued) Unless otherwise specified, VIN = 12V Symbol ∆VO Parameter Line Regulation Typ Max 8.5V ≤ VIN ≤ 20V Conditions Min 65 175 9V ≤ VIN ≤ 20V 55 125 1mA ≤ IO ≤ 100mA 13 80 ∆VO Load Regulation IQ Quiescent Current ∆IQ Quiescent Current Change 8V ≤ VIN ≤ 20V 1.5 1mA ≤ IO ≤ 40mA 0.1 Vn Output Noise Voltage f = 10 Hz to 100 kHz (Note 4) Ripple Rejection f = 120 Hz 10V ≤ VIN ≤ 20V 1mA ≤ IO ≤ 40mA 40 Peak Output Current IPK Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation 6 40 2 5.5 Units mV mA 50 µV 46 dB 140 mA −0.75 mV/˚C 7.9 V LM78L82AC Unless otherwise specified, VIN = 14V Symbol VO ∆VO Parameter Conditions Output Voltage Line Regulation Min Typ Max 7.87 8.2 8.53 11V ≤ VIN ≤ 23V 1mA ≤ IO ≤ 40mA (Note 3) 7.8 8.6 1mA ≤ IO ≤ 70mA (Note 3) 7.8 8.6 11V ≤ VIN ≤ 23V 80 175 12V ≤ VIN ≤ 23V 70 125 1mA ≤ IO ≤ 100mA 15 80 ∆VO Load Regulation IQ Quiescent Current ∆IQ Quiescent Current Change 12V ≤ VIN ≤ 23V 1.5 1mA ≤ IO ≤ 40mA 0.1 Vn Output Noise Voltage f = 10 Hz to 100 kHz (Note 4) Ripple Rejection f = 120 Hz 12V ≤ VIN ≤ 22V 1mA ≤ IO ≤ 40mA IPK Peak Output Current Average Output Voltage Tempco VIN (Min) www.national.com IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation 4 39 8 40 2 5.5 Units V mV mA 60 µV 45 dB 140 mA −0.8 mV/˚C 9.9 V LM78L09AC Unless otherwise specified, VIN = 15V Symbol VO Parameter Conditions Output Voltage ∆VO Line Regulation ∆VO Load Regulation IQ Quiescent Current ∆IQ Quiescent Current Change Vn Min Typ Max 8.64 9.0 9.36 11.5V ≤ VIN ≤ 24V 1mA ≤ IO ≤ 40mA (Note 3) 8.55 9.45 1mA ≤ IO ≤ 70mA (Note 3) 8.55 9.45 11.5V ≤ VIN ≤ 24V 100 200 13V ≤ VIN ≤ 24V 90 150 1mA ≤ IO ≤ 100mA 20 90 1mA ≤ IO ≤ 40mA 10 45 2 5.5 11.5V ≤ VIN ≤ 24V 1.5 1mA ≤ IO ≤ 40mA 0.1 Output Noise Voltage Ripple Rejection f = 120 Hz 15V ≤ VIN ≤ 25V 38 Peak Output Current IPK Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation Units V mV mA 70 µV 44 dB 140 mA −0.9 mV/˚C 10.7 V LM78L12AC Unless otherwise specified, VIN = 19V Symbol VO ∆VO Parameter Line Regulation ∆VO Load Regulation IQ Quiescent Current ∆IQ Quiescent Current Change Vn Min Typ Max 11.5 12 12.5 14.5V ≤ VIN ≤ 27V 1mA ≤ IO ≤ 40mA (Note 3) 11.4 12.6 1mA ≤ IO ≤ 70mA (Note 3) 11.4 12.6 14.5V ≤ VIN ≤ 27V 30 180 16V ≤ VIN ≤ 27V 20 110 1mA ≤ IO ≤ 100mA 30 100 1mA ≤ IO ≤ 40mA 10 50 3 5 16V ≤ VIN ≤ 27V 1 1mA ≤ IO ≤ 40mA 0.1 Output Noise Voltage Ripple Rejection IPK Conditions Output Voltage f = 120 Hz 15V ≤ VIN ≤ 25 Peak Output Current Average Output Voltage Tempco IO = 5mA 5 40 Units V mV mA 80 µV 54 dB 140 mA −1.0 mV/˚C www.national.com LM78LXX Series LM78LXX Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, Bold typeface applies over 0˚C to 125˚C for SO-8 and TO-92 packages, and −40˚C to 85˚C for micro SMD package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO = 40mA, CI = 0.33µF, CO = 0.1µF. (Continued) LM78LXX Series LM78LXX Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, Bold typeface applies over 0˚C to 125˚C for SO-8 and TO-92 packages, and −40˚C to 85˚C for micro SMD package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO = 40mA, CI = 0.33µF, CO = 0.1µF. (Continued) LM78L12AC (Continued) Unless otherwise specified, VIN = 19V Symbol VIN (Min) Parameter Conditions Min Minimum Value of Input Voltage Required to Maintain Line Regulation Typ Max Units 13.7 14.5 V Units LM78L15AC Unless otherwise specified, VIN = 23V Symbol VO Parameter Conditions Output Voltage ∆VO Line Regulation ∆VO Load Regulation IQ Quiescent Current ∆IQ Vn Quiescent Current Change Min Typ Max 14.4 15.0 15.6 17.5V ≤ VIN ≤ 30V 1mA ≤ IO ≤ 40mA (Note 3) 14.25 15.75 1mA ≤ IO ≤ 70mA (Note 3) 14.25 15.75 17.5V ≤ VIN ≤ 30V 37 250 20V ≤ VIN ≤ 30V 25 140 1mA ≤ IO ≤ 100mA 35 150 1mA ≤ IO ≤ 40mA 12 75 3 5 20V ≤ VIN ≤ 30V 1 1mA ≤ IO ≤ 40mA 0.1 Output Noise Voltage Ripple Rejection f = 120 Hz 18.5V ≤ VIN ≤ 28.5V Peak Output Current IPK Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation 37 V mV mA 90 µV 51 dB 140 mA −1.3 mV/˚C 16.7 17.5 V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device outside of its stated operating conditions. Note 2: Human body model, 1.5 kΩ in series with 100pF. Note 3: Power dissipation ≤ 0.75W. Note 4: Recommended minimum load capacitance of 0.01µF to limit high frequency noise. Note 5: Typical thermal resistance values for the packages are: Z Package: θJC = 60 ˚C/W, = θJA = 230 ˚C/W M Package: θJA = 180 ˚C/W micro SMD Package: θJA = 230.9˚C/W www.national.com 6 LM78LXX Series Typical Performance Characteristics Maximum Average Power Dissipation (Z Package) Peak Output Current 00774414 00774416 Dropout Voltage Ripple Rejection 00774417 00774418 Output Impedance Quiescent Current 00774420 00774419 7 www.national.com LM78LXX Series Typical Performance Characteristics (Continued) Quiescent Current 00774421 Equivalent Circuit LM78LXX 00774407 www.national.com 8 LM78LXX Series Typical Applications Fixed Output Regulator 00774408 *Required if the regulator is located more than 3" from the power supply filter. **See (Note 4) in the electrical characteristics table. Adjustable Output Regulator 00774409 VOUT = 5V + (5V/R1 + IQ) R2 5V/R1 > 3 IQ, load regulation (Lr) ≈ [(R1 + R2)/R1] (Lr of LM78L05) Current Regulator 00774410 IOUT = (VOUT/R1) + IQ > IQ = 1.5mA over line and load changes 5V, 500mA Regulator with Short Circuit Protection 00774411 *Solid tantalum. **Heat sink Q1. ***Optional: Improves ripple rejection and transient response. Load Regulation: 0.6% 0 ≤ IL ≤ 250mA pulsed with tON = 50ms. 9 www.national.com LM78LXX Series Typical Applications (Continued) ± 15V, 100mA Dual Power Supply 00774412 *Solid tantalum. Variable Output Regulator 0.5V-18V 00774413 *Solid tantalum. VOUT = VG + 5V, R1 = (−VIN/IQ LM78L05) VOUT = 5V (R2/R4) for (R2 + R3) = (R4 + R5) A 0.5V output will correspond to (R2/R4) = 0.1 (R3/R4) = 0.9 www.national.com 10 LM78LXX Series Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTERCLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC. 8-Bump micro SMD for LM78L05IBP Only NS Package Number BPA08AAB X1 = 1.285mm X2 = 1.285mm X3 = 0.850mm 11 www.national.com LM78LXX Series Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8-Bump micro SMD for LM78L09ITP Only NS Package Number TPA08AAA X1 = 1.285mm X2 = 1.285mm X3 = 0.500mm www.national.com 12 LM78LXX Series Physical Dimensions inches (millimeters) unless otherwise noted (Continued) S.O. Package (M) NS Package Number M08A 13 www.national.com LM78LXX Series 3-Terminal Positive Regulators Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Offset TO-92 (Z) NS Package Number Z03A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560