BSI Very Low Power/Voltage CMOS SRAM 128K X 16 bit FEATURES • Wide Vcc operation voltage : 2.4V ~ 5.5V • Very low power consumption : Vcc = 3.0V C-grade: 29mA (@55ns) operating current I -grade: 30mA (@55ns) operating current C-grade: 24mA (@70ns) operating current I -grade: 25mA (@70ns) operating current 0.3uA(Typ.) CMOS standby current Vcc = 5.0V C-grade: 60mA (@55ns) operating current I -grade: 62mA (@55ns) operating current C-grade: 53mA (@70ns) operating current I -grade: 55mA (@70ns) operating current 1.0uA(Typ.) CMOS standby current • High speed access time : -55 55ns -70 70ns • Automatic power down when chip is deselected • Three state outputs and TTL compatible PRODUCT FAMILY PRODUCT FAMILY OPERATING TEMPERATURE BS616LV2016DC BS616LV2016EC BS616LV2016AC BS616LV2016DI BS616LV2016EI BS616LV2016AI Vcc RANGE • Fully static operation • Data retention supply voltage as low as 1.5V • Easy expansion with CE and OE options • I/O Configuration x8/x16 selectable by LB and UB pin DESCRIPTION The BS616LV2016 is a high performance , very low power CMOS Static Random Access Memory organized as 131,072 words by 16 bits and operates from a wide range of 2.4V to 5.5V supply voltage. Advanced CMOS technology and circuit techniques provide both high speed and low power features with a typical CMOS standby current of 0.3uA at 3.0V /25oC and maximum access time of 55ns at 3.0V / 85oC. Easy memory expansion is provided by active LOW chip enable (CE), active LOW output enable(OE) and three-state output drivers. The BS616LV2016 has an automatic power down feature, reducing the power consumption significantly when chip is deselected. The BS616LV2016 is available in DICE form , JEDEC standard 44-pin TSOP Type II package and 48-ball BGA package. SPEED ( ns ) PKG TYPE ( ICC, Max ) 55ns: 3.0~5.5V 70ns: 2.7~5.5V Vcc=3.0V Vcc=5.0V Vcc=3.0V 70ns Vcc=5.0V 70ns +0 O C to +70 O C 2.4V ~5.5V 55/70 3.0uA 10uA 24mA 53mA -40 O C to +85 O C 2.4V ~ 5.5V 55/70 5.0uA 30uA 25mA 55mA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 POWER DISSIPATION STANDBY Operating ( ICCSB1, Max ) PIN CONFIGURATIONS A4 A3 A2 A1 A0 CE DQ0 DQ1 DQ2 DQ3 VCC GND DQ4 DQ5 DQ6 DQ7 WE A16 A15 A14 A13 A12 BS616LV2016 BLOCK DIAGRAM BS616LV2016EC BS616LV2016EI 2 3 DICE TSOP2-44 BGA-48-0608 DICE TSOP2-44 BGA-48-0608 4 5 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB DQ15 DQ14 DQ13 DQ12 GND VCC DQ11 DQ10 DQ9 DQ8 NC A8 A9 A10 A11 NC A8 A13 A15 Address A16 A14 A12 Input Buffer A7 A6 A5 A4 16 DQ0 . . . . . . . . OE A0 A1 A2 N.C. B D8 UB A3 A4 CE D0 Memory Array Decoder 1024 x 2048 Data Input Buffer 16 Column I/O Write Driver Sense Amp 16 Data Output Buffer DQ15 LB 1024 Row 2048 6 A 20 128 16 Column Decoder 14 CE WE C D9 D10 A5 A6 D1 D2 OE UB LB D VSS D11 N.C. A7 D3 VCC E VCC D12 N.C. A16 D4 VSS F D14 D13 A14 A15 D5 D6 G D15 N.C. A12 A13 WE D7 H N.C. A8 A9 A10 A11 N.C. Control Address Input Buffer A11 A9 A3 A2 A1 A0 A10 Vcc Gnd Brilliance Semiconductor, Inc. reserves the right to modify document contents without notice. R0201-BS616LV2016 1 Revision 1.1 Jan. 2004 BSI BS616LV2016 PIN DESCRIPTIONS Name Function A0-A16 Address Input These 17 address inputs select one of the 131,072 x 16-bit words in the RAM. CE Chip Enable Input CE is active LOW. Chip enables must be active when data read from or write to the device. if chip enable is not active, the device is deselected and is in a standby power mode. The DQ pins will be in the high impedance state when the device is deselected. WE Write Enable Input The write enable input is active LOW and controls read and write operations. With the chip selected, when WE is HIGH and OE is LOW, output data will be present on the DQ pins; when WE is LOW, the data present on the DQ pins will be written into the selected memory location. OE Output Enable Input The output enable input is active LOW. If the output enable is active while the chip is selected and the write enable is inactive, data will be present on the DQ pins and they will be enabled. The DQ pins will be in the high impedance state when OE is inactive. LB and UB Data Byte Control Input Lower byte and upper byte data input/output control pins. DQ0 - DQ15 Data Input/Output Ports These 16 bi-directional ports are used to read data from or write data into the RAM. Vcc Power Supply Gnd Ground TRUTH TABLE MODE Not selected (Power Down) Output Disabled Read Write R0201-BS616LV2016 CE H WE OE LB UB D0~D7 D8~D15 X X X X High Z High Z ICCSB , I CCSB1 X X X H H High Z L L X H X H H X H X High Z High Z High Z High Z ICCSB , I CCSB1 ICC L L Dout H L L H L L L L H L L X Vcc CURRENT High Z ICC Dout ICC High Z Dout ICC Dout High Z ICC Din Din ICC H L X Din ICC L H Din X ICC 2 Revision 1.1 Jan. 2004 BSI BS616LV2016 ABSOLUTE MAXIMUM RATINGS(1) SYMBOL PARAMETER OPERATING RANGE RATING UNITS -0.5 to Vcc+0.5 V V TERM Terminal Voltage with Respect to GND T BIAS Temperature Under Bias -40 to +85 O T STG Storage Temperature -60 to +150 O PT Power Dissipation 1.0 W I OUT DC Output Current 20 mA RANGE AMBIENT TEMPERATURE Vcc Commercial 0 O C to +70 O C 2.4V ~ 5.5V Industrial -40 O C to +85 O C 2.4V ~ 5.5V C C CAPACITANCE (1) (TA = 25oC, f = 1.0 MHz) 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. SYMBOL CIN CDQ PARAMETER Input Capacitance Input/Output Capacitance CONDITIONS MAX. UNIT VIN=0V 6 pF VI/O=0V 8 pF 1. This parameter is guaranteed and not 100% tested. DC ELECTRICAL CHARACTERISTICS ( TA = -40 to + 85oC ) PARAMETER NAME PARAMETER V IL Guaranteed Input Low (3) Voltage Vcc =3.0V V IH Guaranteed Input High (3) Voltage Vcc =3.0V 2.0 Vcc =5.0V 2.2 IIL Input Leakage Current Vcc = Max, V IN = 0V to Vcc ILO Output Leakage Current Vcc = Max,CE = V IH or OE = V IH, V I/O = 0V to Vcc V OL Output Low Voltage Vcc = Max, IOL = 2.0mA V OH Output High Voltage Vcc = Min, IOH = -1.0mA Operating Power Supply Current CE = V IL, (2) IDQ = 0mA, F = Fmax Standby Current-TTL CE=V IH IDQ = 0mA TEST CONDITIONS Vcc =5.0V MIN. TYP. (1) MAX. UNITS -0.5 -- 0.8 V -- V cc+0.3 V -- -- 1 uA -- -- 1 uA -- -- 0.4 V 2.4 -- -- V -- -- -- -- Vcc =3.0V Vcc =5.0V Vcc =3.0V ICC (5) ICCSB ICCSB1 (4) Standby Current-CMOS Vcc =5.0V Vcc =3V 70ns Vcc =5V 70ns Vcc =3.0V mA 0.5 Vcc =5.0V CE ≧ V cc-0.2V, V IN≧V cc-0.2V or V IN≦0.2V 25 55 mA 1.0 Vcc =3.0V -- Vcc =5.0V 0.3 5 1.0 30 uA 1. Typical characteristics are at TA = 25oC. 2. Fmax = 1/tRC. 3. These are absolute values with respect to device ground and all overshoots due to system or tester notice are included. 4.IccsB1_Max. is 3uA / 10uA at Vcc=3V / 5V and TA=70oC. 5. Icc_Max. is 30mA(@3V) / 62mA(@5V) under 55ns operation. DATA RETENTION CHARACTERISTICS ( TA = -40 to + 85oC ) SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNITS Vcc for Data Retention CE ≧ Vcc - 0.2V VIN ≧ Vcc - 0.2V or VIN ≦ 0.2V 1.5 -- -- V ICCDR Data Retention Current CE ≧ Vcc - 0.2V VIN ≧ Vcc - 0.2V or VIN ≦ 0.2V -- 0.1 1.0 uA tCDR Chip Deselect to Data Retention Time -- -- ns -- -- ns VDR (3) tR See Retention Waveform Operation Recovery Time 1. Vcc = 1.5V, TA = + 25 C O R0201-BS616LV2016 0 TRC 2. tRC = Read Cycle Time 3 (2) 3. IccDR_MAX. is 0.7uA at TA=70oC. Revision 1.1 Jan. 2004 BSI BS616LV2016 LOW VCC DATA RETENTION WAVEFORM ( CE Controlled ) Data Retention Mode Vcc VDR ≥ 1.5V Vcc Vcc tR t CDR CE ≥ Vcc - 0.2V VIH CE VIH KEY TO SWITCHING WAVEFORMS AC TEST CONDITIONS (Test Load and Input/Output Reference) Input Pulse Levels Vcc / 0V Input Rise and Fall Times 1V/ns WAVEFORM Input and Output Timing Reference Level 0.5Vcc Output Load CL = 100pF+1TTL CL = 30pF+1TTL INPUTS OUTPUTS MUST BE STEADY MUST BE STEADY MAY CHANGE FROM H TO L WILL BE CHANGE FROM H TO L MAY CHANGE FROM L TO H WILL BE CHANGE FROM L TO H , DON T CARE: ANY CHANGE PERMITTED CHANGE : STATE UNKNOWN DOES NOT APPLY CENTER LINE IS HIGH IMPEDANCE ”OFF ”STATE AC ELECTRICAL CHARACTERISTICS ( TA = -40 to + 85oC ) READ CYCLE JEDEC PARAMETER NAME PARAMETER NAME tAVAX tRC Read Cycle Time 55 -- -- 70 -- -- ns tAVQV tAA Address Access Time -- -- 55 -- -- 70 ns tELQV tACS Chip Select Access Time (CE) -- -- 55 -- -- 70 ns tBA tBA (1) Data Byte Control Access Time (LB,UB) -- -- 30 -- -- 35 ns -- -- 30 -- -- 35 ns DESCRIPTION CYCLE TIME : 55ns CYCLE TIME : 70ns MIN. TYP. MAX. MIN. TYP. MAX. (Vcc = 2.7~5.5V) (Vcc = 3.0~5.5V) UNIT tGLQV tOE Output Enable to Output Valid t E1LQX tCLZ Chip Select to Output Low Z (CE) 10 -- -- 10 -- -- ns tBE tBE Data Byte Control to Output Low Z (LB,UB) 10 -- -- 10 -- -- ns tGLQX tOLZ Output Enable to Output in Low Z 5 -- -- 5 -- -- ns tEHQZ tCHZ Chip Deselect to Output in High Z (CE) -- -- 30 -- -- 35 ns tBDO tBDO Data Byte Control to Output High Z (LB,UB) tGHQZ tOHZ Output Disable to Output in High Z tAXOX tOH Data Hold from Address Change -- -- 30 -- -- 35 ns -- -- 25 -- -- 30 ns 10 -- -- 10 -- -- ns NOTE : 1. tBA is 30ns/35ns (@speed=55ns/70ns) with address toggle. ; tBA is 55ns/70ns (@speed=55ns/70ns) without address toggle. R0201-BS616LV2016 4 Revision 1.1 Jan. 2004 BSI BS616LV2016 SWITCHING WAVEFORMS (READ CYCLE) READ CYCLE1 (1,2,4) t RC ADDRESS t t t OH AA OH D OUT READ CYCLE2 (1,3,4) CE t ACS t BA LB,UB t BE t D OUT READ CYCLE3 t BDO (5) CLZ t (5) CHZ (1,4) t RC ADDRESS t AA OE t OH t OE t OLZ CE (5) t CLZ t t OHZ (5) t CHZ(1,5) ACS t BA LB,UB t BE t BDO D OUT NOTES: 1. WE is high for read Cycle. 2. Device is continuously selected when CE = VIL. 3. Address valid prior to or coincident with CE transition low. 4. OE = VIL . 5. The parameter is guaranteed but not 100% tested. R0201-BS616LV2016 5 Revision 1.1 Jan. 2004 BSI BS616LV2016 AC ELECTRICAL CHARACTERISTICS ( TA = -40 to + 85oC ) WRITE CYCLE JEDEC PARAMETER NAME PARAMETER NAME tAVAX tE1LWH tAVWL tAVWH tWLWH tWHAX tBW tWLQZ tDVWH tWHDX tGHQZ t WC t CW t AS t AW t WP t WR t BW (1) t WHZ t DW t DH t OHZ tWHOX t OW CYCLE TIME : 55ns CYCLE TIME : 70ns MIN. TYP. MAX. MIN. TYP. MAX. (Vcc = 2.7~5.5V) (Vcc = 3.0~5.5V) DESCRIPTION UNIT 55 -- -- 70 -- -- ns 55 -- -- 70 -- -- ns 0 -- -- 0 -- -- ns Address Valid to End of Write 55 -- -- 70 -- -- ns Write Pulse Width 30 -- -- 35 -- -- ns (CE,WE) 0 -- -- 0 -- -- ns (LB,UB) 25 -- -- 30 -- -- ns -- -- 25 -- -- 30 ns Data to Write Time Overlap 25 -- -- 30 -- -- ns Data Hold from Write Time 0 -- -- 0 -- -- ns Output Disable to Output in High Z -- -- 25 -- -- 30 ns End of Write to Output Active 5 -- -- 5 -- -- ns Write Cycle Time Chip Select to End of Write (CE) Address Setup Time Write recovery Time Date Byte Control to End of Write Write to Output in High Z NOTE : 1. tBW is 25ns/30ns (@speed=55ns/70ns) with address toggle. ; tBW is 55ns/70ns (@speed=55ns/70ns) without address toggle. SWITCHING WAVEFORMS (WRITE CYCLE) WRITE CYCLE1 (1) t WC ADDRESS (3) t WR OE (11) t CW (5) CE t BW LB,UB t AW WE (3) t WP t AS (2) (4,10) t OHZ D OUT t DH t DW D IN R0201-BS616LV2016 6 Revision 1.1 Jan. 2004 BSI BS616LV2016 WRITE CYCLE2 (1,6) t WC ADDRESS (11) t CW (5) CE t BW LB,UB t AW WE t WR t WP (3) (2) t AS (4,10) t WHZ D OUT t OW t DH (7) (8) t DW (8,9) D IN NOTES: 1. WE must be high during address transitions. 2. The internal write time of the memory is defined by the overlap of CE and WE low. All signals must be active to initiate a write and any one signal can terminate a write by going inactive. The data input setup and hold timing should be referenced to the second transition edge of the signal that terminates the write. 3. TWR is measured from the earlier of CE or WE going high at the end of write cycle. 4. During this period, DQ pins are in the output state so that the input signals of opposite phase to the outputs must not be applied. 5. If the CE low transition occurs simultaneously with the WE low transitions or after the WE transition, output remain in a high impedance state. 6. OE is continuously low (OE = VIL ). 7. DOUT is the same phase of write data of this write cycle. 8. DOUT is the read data of next address. 9. If CE is low during this period, DQ pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 10. The parameter is guaranteed but not 100% tested. 11. TCW is measured from the later of CE going low to the end of write. R0201-BS616LV2016 7 Revision 1.1 Jan. 2004 BSI BS616LV2016 ORDERING INFORMATION BS616LV2016 X X Z YY SPEED 55: 55ns 70: 70ns PKG MATERIAL -: Normal G: Green P: Pb free GRADE C: +0oC ~ +70oC I: -40oC ~ +85oC PACKAGE E: TSOP2-44 A: BGA-48-0608 D: DICE Note: BSI (Brilliance Semiconductor Inc.) assumes no responsibility for the application or use of any product or circuit described herein. BSI does not authorize its products for use as critical components in any application in which the failure of the BSI product may be expected to result in significant injury or death, including life-support systems and critical medical instruments. PACKAGE DIMENSIONS NOTES: 1: CONTROLLING DIMENSIONS ARE IN MILLIMETERS. 2: PIN#1 DOT MARKING BY LASER OR PAD PRINT. 1.4 Max. 3: SYMBOL "N" IS THE NUMBER OF SOLDER BALLS. BALL PITCH e = 0.75 D E N D1 E1 8.0 6.0 48 5.25 3.75 E1 e D1 VIEW A 48 mini-BGA (6 x 8) R0201-BS616LV2016 8 Revision 1.1 Jan. 2004 BSI BS616LV2016 PACKAGE DIMENSIONS TSOP2-44 R0201-BS616LV2016 9 Revision 1.1 Jan. 2004