PRODUCT DATASHEET Leila series last update 2/5/2012 Ordering number CA12816_LXP2-RS2 Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Leila Assembly XT-E Black 21.6 mm 14.6 mm Round PMMA PC Tape Ready FWHM Efficiency cd/lm Gerber File 8 degrees 92 % 15.600 Available FWHM Efficiency cd/lm Gerber File 11 degrees 88 % 8.950 Available FWHM Efficiency cd/lm Gerber File 14+36 degrees 84 % 3.860 Available FWHM Efficiency cd/lm Gerber File 24 degrees 88 % 3.900 Available Ordering number CA11482_LXP2-D Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Leila Assembly XT-E Black 21.6 mm 14.6 mm Round PMMA PC Tape Ready Ordering number CA11484_LXP2-O-90 Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Leila Assembly XT-E Black 21.6 mm 14.5 mm Round PMMA PC Tape Ready Ordering number CA11483_LXP2-M Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Leila Assembly XT-E Black 21.6 mm 14.6 mm Round PMMA PC Tape Ready October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 PRODUCT DATASHEET Leila series last update 2/5/2012 Ordering number CA12392_LXP2-W Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Leila Assembly XT-E Black 21.6 mm 14.6 mm Round PMMA PC Tape Ready FWHM Efficiency cd/lm Gerber File 41 degrees 89 % 1.580 Available NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 PRODUCT DATASHEET Leila series last update 2/5/2012 GENERAL INFORMATION - Product series especially designed & optimized for XT-E series of LEDs. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used material from below: http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdf http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf - Optic holder molded by high quality PC material (120 dergees of Celcius / 248 degrees of Fahrenheit). - Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by clicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. Slanted assembly might cause unbalanced bond to the surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer - this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 A B C D 4 4 Tape 0.4mm Isometric view Scale: 1:1 14.6 3 3 21 2 MATERIALS Lens: PMMA Holder: PC Tape: PU Foam Part no.s: CA11481_LXP2-RS CA11481_LXP2-G-RS CA11482_LXP2-D CA11482_LXP2-G-D CA11483_LXP2-M CA11483_LXP2-G-M CA11484_LXP2-O-90 CA11484_LXP2-G-O-90 1 This drawing is our property. It can't be reproduced or communicated without our written agreement. DRAWN BY DATE CHECKED BY DATE DESIGNED BY DATE .6 2 Oval-version beam direction Led Teh FIN Fin DRAWING TITLE Datasheet Leila LXP2-Series assy pv 02.12.2010 tk 12.04.2010 pv 12.04.2010 D SIZE DRAWING NUMBER REV 1 A4 SCALE 2:1 WEIGHT(g) - SHEET A 1/1 1