AAC CT051003BYM Chip resistors - tin / gold terminations available Datasheet

THIN FILM PRECISION CHIP RESISTORS
The content of this specification may change without notification 10/12/07
CT Series Chip Resistors – Tin / Gold Terminations Available
Custom solutions are available.
HOW TO ORDER
CT G 10
1003
B X M
Packaging
M = Std. Reel
O = 1K Reel
TCR (PPM/°C)
L = +1
P = +5
M = +2
Q = +10
N = +3
X = +25
Tolerance (%)
U=+.01
A=+.05
P=+.02
B=+.10
Y = +50
Z = +100
FEATURES
„ Nichrome Thin Film Resistor Element
C=+.25
D=+.50
F=+1
„ CTG type constructed with top side terminations,
wire bonded pads, and Au termination material.
„ Anti-Leaching Nickel Barrier Terminations
EIA Resistance Value
Standard decade values
Size
20 = 0201
05 = 0402
16 = 0603
10 = 0805
18 = 1206
14 = 1210
13 = 1217
12 = 2010
Termination Material
Sn = Leave Blank
„ Very Tight Tolerances, as low as ±0.02%
„ Extremely Low TCR, as low as ±1ppm
11 = 2020
09 = 2045
01 = 2512
„ Special Sizes available 1217, 2020, and 2045
„ Either ISO 9001 or ISO/TS 16949:2002
Certified
„ Applicable Specifications: EIA575, IEC 60115-1,
JIS C5201-1, CECC 40401, MIL-R-55342D
Au = G
Series
CT = Thin Film Precision Resistors
SCHEMATIC
DIMENSIONS (mm)
Wraparound Termination
Size
L
W
c
d
t
0201
0.60 + 0.05
0.30 + 0.05
0.13 + 0.05
0.25+0.05
0.25 + 0.05
0402
1.00 + 0.05
0.5+0.1
-0.05
0.20 + 0.10
0.25+0.05
-0.10
0.35 + 0.05
0603
1.60 + 0.10
0.80 + 0.10
0.20 + 0.10
0.30+0.20
-0.10
0.50 + 0.10
0805
2.00 + 0.15
1.25 + 0.15
0.40 + 0.25
0.30+0.20
-0.10
0.50 + 0.15
1206
3.20 + 0.15
1.60 + 0.15
0.45 + 0.25
0.40+0.20
-0.10
0.60 + 0.15
1210
3.20 + 0.15
2.60 + 0.15
0.50 + 0.30
0.40+0.20
-0.10
0.60 + 0.10
1217
3.00 + 0.20
4.20 + 0.20
0.80 + 0.30
2010
5.00 + 0.15
2.60 + 0.15
0.50 + 0.30
2020
5.08 + 0.20
5.08 + 0.20
0.80 + 0.30
2045
5.00 + 0.15
11.5+ 0.30
0.80 + 0.30
0.80 + 0.30
0.9 max
2512
6.30 + 0.15
3.10 + 0.15
0.60 + 0.25
0.50 + 0.25
0.60 + 0.10
Top Side Termination, Bottom Isolated – CTG Type
Wire Bond Pads
Terminal Material: Au
0.80 + 0.25
0.40+0.20
-0.10
0.80 + 0.30
0.9 max
0.70 + 0.10
0.9 max
CONSTRUCTION FIGURE (Wraparound)
CONSTRUCTION MATERIALS
Item
n
o
p
pa
pb
pc
pd
q
r&
s
Part
Material
Resistor
Nichrome Thin Film
Protective Film
Polymide Epoxy Resin
Electrode
Grounding Layer
Nichrome Thin Film
Electrode Layer
Copper Thin Film
Barrier Layer
Nickel Plating
Solder Layer
Solder Plating (Sn)
Substrate
Alumina
Marking
Epoxy Resin
The resistance value is on the front side
The production month is on the backside
American Accurate Components, Inc.
188 Technology Drive, Unit H, Irvine, CA 92618
TEL: 949-453-9888 Š FAX: 949-453-8889
1
THIN FILM PRECISION CHIP RESISTORS
The content of this specification may change without notification 10/12/07
ELECTRICAL CHARACTERISTICS
Size
Power Rating
at 70° (W)
0201
0.05
0402
0603
0805
1206
1210
1217
2010
0.031
0.063
0.063
0.100
0.100
0.125
0.250
0.250
0.250
Resistance Range
±% Tolerance
TCR (10-6/°C)
10.0 ~ 30.0
1
±100
33.0 ~ 22.0K
0.5
±25
10.0 ~ 46.4
0.1, 0.5, 1
±10, ±25, ±50
47.0 ~ 97.6
0.05, 0.1, 0.25, 0.5, 1
±10, ±25, ±50
100 ~ 2.94K
0.02, 0.05, 0.1, 0.25, 0.5, 1
±5, ±10, ±25, ±50
3.00K ~ 100K
0.05, 0.1, 0.25, 0.5, 1
±10, ±25, ±50
10.0 ~ 100K
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
1,2,3,5,10,25,50
102K ~ 270K
0.05, 0.1, 0.25, 0.5, 1
10, 25, 50
274K ~ 360K
0.1, 0.25, 0.5, 1
10, 25, 50
10.0 ~ 200K
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
1, 2, 3, 5, 10, 25, 50
205K ~ 360K
0.05, 0.1, 0.25, 0.5
10, 25, 50
365K ~ 487K
0.05, 0.1, 0.25, 0.5
10, 25
499K ~ 1.00M
0.1, 0.5
25
5.01 ~ 560K
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
1, 2, 3, 5, 10, 25, 50
562K ~ 1.00M
0.05, 0.1, 0.25, 0.5
10, 25
100 ~ 330K
0.1
±5, ±10
51.0 ~ 2.00M
0.1, 0.5
±25
10.0 ~ 49.9
0.5
±50
5.10 ~ 1.00M
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
±1, 2, 3, 5, 10, 25
100 ~ 20.0K
0.01, 0.05, 0.1, 0.25, 0.5
±5
50.0 ~ 40.0K
0.01, 0.05, 0.1, 0.25, 0.5
±10
10.0 ~500K
0.01, 0.05
4.70 -1.00M
0.1, 0.25, 0.5, 1
10.0 ~500K
0.01, 0.05
1.00 ~ 1.00M
0.1, 0.25, 0.5, 1
Working
Voltage
Overload
Voltage
Operating
Temp Range
15V
30V
-55°C ~ +125°C
50V
100V
-55°C ~ +125°C
-55°C ~ +125°C
-55°C ~ +155°C
75V
150V
-55°C ~ +125°C
±25
100V
200V
-55°C ~ +125°C
150V
300V
-55°C ~ +125°C
200V
400V
-55°C ~ +125°C
200V
400V
-55°C ~ +155°C
150V
300V
-55°C ~ +125°C
±50
2020
0.500
5.10 ~ 2.00M
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
±1, 2, 3, 5, 10, 25
350V
700V
-55°C ~ +155°C
2045
1.000
20.0 ~ 4.99M
0.01, 0.02, 0.05, 0.1, 0.25, 0.5, 1
±1, 2, 3, 5, 10, 25
500V
1000V
-55°C ~ +155°C
100 ~ 20.0K
0.01, 0.05, 0.1, 0.25, 0.5
±5
50.0 ~ 40.0K
0.01, 0.05, 0.1, 0.25, 0.5
±10
10.0R ~ 500K
0.01, 0.05
150V
300V
4.70 -1.00M
0.1, 0.25, 0.5, 1
-55°C ~ +125°C
10.0R ~ 500K
0.01, 0.05
1.00 1.00M
0.1, 0.25, 0.5, 1
2512
0.500
* Rated Voltage: √PxR
American Accurate Components, Inc.
±25
±50
** 0.01% may be available under special request
188 Technology Drive, Unit H, Irvine, CA 92618
TEL: 949-453-9888 Š FAX: 949-453-8889
2
THIN FILM PRECISION CHIP RESISTORS
The content of this specification may change without notification 10/12/07
PERFORMANCE & ENVIRONMENTAL SPECIFICATIONS
Maximum ∆ Ω +0.05Ω (Tolerance)
A
B, C
D, F
± 0.1%
± 0.1%
± 0.5%
Test Item
Short Time Overload
Load Life
± 0.1%
± 0.25%
± 0.5%
Moisture Load Life
± 0.1%
± 0.25%
± 0.5%
Temperature Cycle
± 0.1%
± 0.1%
± 0.5%
Resistance to Solder Heat
± 0.05%
± 0.1%
± 0.5%
Terminal Strength
± 0.1%
± 0.1%
± 0.5%
A new uniform coating of solder
shall cover minimum of 95% of
surface being immersed
DC 500V for 1 minute
Solderability
Insulation Resistance
Condition
2.5 times of the rated voltage shall be applied for 5 seconds
The resistor shall be subjected to rated voltage for 90 min. followed by a pause of
30 min. at a temperature of 70±3ºC. This constitutes 1 cycle. Cycles shall be
repeated for 1000 hours.
The resistor subjected to rated voltage for 90 min followed by a pause for 30 min
at a temperature of 60±2ºC with relative humidity of 90% to 95%. This constitutes
1 cycles. Cycles shall be repeated for 1000 hours.
[-55ºC 30 min → +125ºC 30 min → R.T. 3 min] The resistor shall be subjected to
5 continuous cycles
The resistor shall withstand dipped into solder for 10±1 sec. At 260±5ºC
Distance between fulcrums: 90mm; Bending width: 3 mm
The resistor shall be dipped into the solder of 235±5ºC for 3±0.5 seconds
1000 Meg Ω or over
VALUE MARKING
REEL SCHEMATIC & DIMENSIONS (mm)
For those parts ordered with an E-24 value, the product will be
marked with a 3 digit code. For those products ordered with an
E-96 value, the product will be marked with a 4 digit code. For
those parts which fall under E-96 and E-24 values (e.g. 1K ohm
is both an E-96 and E-24 value), the part will be marked with a 3
digit code; 4 digit markings for this type is available upon special
request.
O & M Type
7” Reel
C
∅13± 0.2
E
60±0.5
F
11.4±1.0
G
9.0±0.3
H
1.5±0.3
M ∅180±2.0
0201, and 0402 Size
No marking
E-24 & E-96 Values
Custom Value Any Size
Reel size is dependent upon the package
quantity& resistor size. Call for more info.
TAPE SCHEMATIC
0603 Size
EIA 96 Digit Code of 3.32K ohm
E-96 Values
51B
103
1213
0603 ~ 2512 Sizes
EIA 3 Digit Code of 10K ohm resistor
E-24 Values, E-96 Values
0805 ~ 2512 Sizes
EIA 4 Digit Code of 121K ohm resistor
E-96 Values
TAPE DIMENSIONS (mm)
LABEL DESCRIPTION
One side surface of a reel is marked with a label with the
following items of information.
1. Chip Resistor
2. Part Number
3. Tolerance
4. Quantity
5. Lot number for production month/year*
6. Manufacturer’s name or symbol
* The suffix “L” indicates that this item is lead free. As of September 2004, all new
production items of the series CR and CJ are no longer containing tin/lead (SnPb)
terminals; they are lead free and in compliance with Lead Free/RoHS.
PACKAGE QUANTITY
Type
M
O
Type
B
O
0201
5,000
1,000
1210
5,000
1,000
M Type
13” Reel
∅13±0.2
100±0.2
13.5±1.0
9.5±0.5
2.0±0.5
∅330±2.0
0402
10,000
1,000
1217
2,000
1,000
American Accurate Components, Inc.
0603
5,000
1,000
2010
4,000
1,000
0805
5,000
1,000
2020
2,000
1,000
2045
3,000
1,000
1206
5,000
1,000
2512
4,000
1,000
A
B
W
E
F
P1
T
Tp
0201
0.41±0.1
0.71±0.1
8.0±0.2
1.75±0.10
3.5±0.05
2.0±0.05
0.5max
0.4+0.05
A
B
W
E
F
P1
T
Tp
1210
2.9±0.1
3.5±0.1
8.0±0.2
1.75±0.1
3.5±0.05
4.0±0.1
0.90±0.1
0.75±0.1
0402
0.65±0.1
1.15±0.1
8.0±0.2
1.75±0.10
3.5±0.05
2.0±0.05
0.55±0.1
0.40±0.05
1217
3.5±0.1
4.9±0.1
12.0±0.2
1.75±0.1
5.5±0.1
8.0±0.1
0.90±0.1
0603
1.1±0.2
1.9±0.2
8.0±0.2
1.75±0.1
3.5±0.05
4.0±0.1
0.70±0.1
0.60±0.1
2010
2.9±0.1
5.3±0.1
12.0±0.2
1.75±0.1
5.5±0.1
4.0±0.1
1.0±0.1
0.25±0.1
2020
5.5±0.1
5.5±0.1
12.0±0.2
1.75±0.1
5.5±0.1
8.0±0.1
1.0±0.1
0805
1.65±0.2
2.4±0.2
8.0±0.2
1.75±0.1
3.5±0.05
4.0±0.1
0.90±0.1
0.75±0.1
2045
5.4±0.1
11.9±0.1
24.0±0.2
1.75±0.1
11.5±0.1
8.0±0.1
1.0±0.1
1206
2.0±0.15
3.6±0.15
8.0±0.2
1.75±0.1
3.5±0.05
4.0±0.1
0.90±0.1
0.75±0.1
2512
2.9±0.1
5.3±0.1
12.0±0.2
1.75±0.1
5.5±0.05
4.0±0.1
1.0±0.1
0.25±0.1
Call to find out if the tape material is paper or plastic
188 Technology Drive, Unit H, Irvine, CA 92618
TEL: 949-453-9888 Š FAX: 949-453-8889
3
Similar pages