LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Long life, Overvoltage-proof design, 105C LXH @No sparks against DC over-voltage @Same case sizes of KMH @Endurance with ripple current : 105C 5000 hours @Non solvent-proof type @Pb-free design downsized longer life KLG CHA downsized ?SPECIFICATIONS Items Characteristics Category Temperature Range -25 to +105C 200 & 400Vdc P20% (M) I=0.02CV or 3mA, whichever is smaller. Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V) Rated Voltage Capacitance Tolerance Leakage Current Dissipation Factor (tane) 0.15 max. Low Temperature Characteristics Z(-25C) /Z(+20C)[4 (at 20C, 120Hz) Shelf Life ?DIMENSIONS [mm] @105c Endurance with Rated Ripple Current @Terminal Code : VS (F22 to F35) 10 FD+1max. PC board pin-out * 4.0P0.5 LP2 2-F2 *FD=35mm : 3.5P0.5mm No plastic disk is the standard design 4 5 6 7 8 9 10 11 12 13 14 15 16 17 tanE 3 18 E L XH AAA VS N AAA M AAA S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 68MF:680,1500MF:152) Dummy terminal code Terminal code Voltage code (ex. 200V:201,400V:401) Series code Category ?RATED RIPPLE CURRENT MULTIPLIERS @Frequency Multipliers 50 0.81 0.77 120 1.00 1.00 300 1.17 1.16 0 -10 -20 -30 1k 1.32 1.30 10k 1.45 1.41 50k 1.50 1.43 0.1 0.01 (MA) 1,000 100 Leakage Current Please refer to "A guide to global code (snap-in type)" Frequency (Hz) 200Vdc 400Vdc +10 1 ?PART NUMBERING SYSTEM 2 200V1000MFF30B45L 400V330MFF30B45L (%) +20 Negative mark Sleeve (PET) Capacitance Change Endurance 1 (at 20C after 5 minutes) (at 120Hz) (at 20C, 1MHz) 50nH max. When an excessive DC voltage is applied to the capacitors under the test conditions on next page, the vent shall operate and then the capacitors shall become open-circuit without burning materials. The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated ripple current is applied for 3000 or 5000 hours at 105C. Capacitance change [P20% of the initial value D.F. (tanE) [200% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C without voltage applied. Capacitance change [P15% of the initial value D.F. (tanE) [150% of the initial specified value Leakage current [The initial specified value ESL DC Overvoltage Test Vent (at 20C, 120Hz) 10 1 0 2,000 4,000 6,000 8,000 (hours) Time (1/2) CAT. No. E1001E LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Long life, Overvoltage-proof design, 105C ?STANDARD RATINGS WV (Vdc) 200 400 Cap (mF) 270 330 330 390 390 470 470 470 560 560 560 680 680 680 680 820 820 820 1000 1000 1200 1200 1500 68 68 82 82 100 100 120 120 120 150 150 150 180 180 180 180 220 220 220 270 270 270 330 330 390 390 470 Case size fDbL(mm) tane 22 B 25 22 B 30 25.4 B 25 22 B 35 25.4 B 30 22 B 40 25.4 B 30 30 B 25 22 B 45 25.4 B 35 30 B 30 22 B 50 25.4 B 40 30 B 30 35 B 25 25.4 B 50 30 B 35 35 B 30 30 B 45 35 B 35 30 B 50 35 B 40 35 B 45 22 B 25 25.4 B 20 22 B 30 25.4 B 25 22 B 35 25.4 B 30 22 B 40 25.4 B 30 30 B 25 22 B 45 25.4 B 35 30 B 30 22 B 50 25.4 B 40 30 B 30 35 B 25 25.4 B 45 30 B 35 35 B 30 25.4 B 50 30 B 40 35 B 30 30 B 45 35 B 35 30 B 50 35 B 40 35 B 45 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 Rated ripple current (Arms/105c,120Hz) Part No. 5000 hours 3000 hours 0.45 0.62 0.62 0.67 0.66 0.72 0.72 0.77 0.80 0.78 0.81 0.89 0.89 0.89 0.88 1.05 1.03 1.05 1.18 1.18 1.33 1.36 1.57 0.26 0.24 0.30 0.30 0.34 0.34 0.37 0.37 0.39 0.42 0.43 0.43 0.49 0.48 0.47 0.48 0.55 0.54 0.55 0.62 0.62 0.59 0.71 0.69 0.80 0.79 0.89 0.87 1.20 1.21 1.31 1.28 1.40 1.41 1.50 1.56 1.53 1.57 1.74 1.74 1.74 1.72 2.04 2.00 2.04 2.30 2.30 2.60 2.65 3.08 0.51 0.46 0.58 0.58 0.66 0.66 0.72 0.72 0.76 0.82 0.84 0.84 0.95 0.94 0.92 0.94 1.07 1.06 1.08 1.21 1.21 1.15 1.39 1.35 1.55 1.54 1.74 ELXH201VSN271MP25S ELXH201VSN331MP30S ELXH201VSN331MQ25S ELXH201VSN391MP35S ELXH201VSN391MQ30S ELXH201VSN471MP40S ELXH201VSN471MQ30S ELXH201VSN471MR25S ELXH201VSN561MP45S ELXH201VSN561MQ35S ELXH201VSN561MR30S ELXH201VSN681MP50S ELXH201VSN681MQ40S ELXH201VSN681MR30S ELXH201VSN681MA25S ELXH201VSN821MQ50S ELXH201VSN821MR35S ELXH201VSN821MA30S ELXH201VSN102MR45S ELXH201VSN102MA35S ELXH201VSN122MR50S ELXH201VSN122MA40S ELXH201VSN152MA45S ELXH401VSN680MP25S ELXH401VSN680MQ20S ELXH401VSN820MP30S ELXH401VSN820MQ25S ELXH401VSN101MP35S ELXH401VSN101MQ30S ELXH401VSN121MP40S ELXH401VSN121MQ30S ELXH401VSN121MR25S ELXH401VSN151MP45S ELXH401VSN151MQ35S ELXH401VSN151MR30S ELXH401VSN181MP50S ELXH401VSN181MQ40S ELXH401VSN181MR30S ELXH401VSN181MA25S ELXH401VSN221MQ45S ELXH401VSN221MR35S ELXH401VSN221MA30S ELXH401VSN271MQ50S ELXH401VSN271MR40S ELXH401VSN271MA30S ELXH401VSN331MR45S ELXH401VSN331MA35S ELXH401VSN391MR50S ELXH401VSN391MA40S ELXH401VSN471MA45S ?DC OVERVOLTAGE TEST CONDITIONS The vent will operate and the capacitor shall become an open circuit without burning materials when the following excess DC voltage is applied. @Test DC voltage Rated Voltage 200Vdc 400Vdc Capacitance Current limit Test DC voltage <330MF 4A 330[C<470MF 5A 300/375Vdc 7A ]470MF <100MF 2A 4A 100[C<220MF 500/600Vdc 7A ]220MF @Test Circuit + AC input SW CX - Constant DC voltage/current power supply (2/2) CAT. No. E1001E