Issue 6.2012 THE SERIALS DOTMATRIX DISPLAYS WITH RS-232 s l a i r TheSe EA SER162-92NLED with snap in housing Accessories: cable EA KV24-9B length: 1,50 m FEATURES * * * * * * * * * * * * * 32 DIFFERENT SIZES OF DISPLAYS AVAILABLE (1x8 UP TO 16x40) SUPPLY VOLTAGE +5V OR OPTIONAL 9..35V1) INCL. LED-ILLUMINATION SWITCHABLE BY MEANS OF SOFTWARE 25 DISPLAYS WITH YELLOW/GREEN LED-BACKLIGHT 7 DISPLAYS WITH LOW POWER WHITE LED-BACKLIGHT 3 DISPLAYS WITH SNAP IN HOUSING HIGH CONTRAST SUPERTWIST LCD INCL. FRONTAL BEZEL WITH ANTIGLARE GLASS2) AUTOMATIC LINE MANAGEMENT CR / LF / SCROLL / CURSOR POSITIONING BAUDRATE SETTING BY JUMPER: 300, 1200, 2400 OR 9600 BAUD POTI FOR CONTRAST ADJUSTMENT ON BOARD MULTIPLE DISPLAYS ON SINGLE RS-232C OPTIONS * SUPPLY +9..35V= INSTEAD OF +5V= * RS-422 INTERFACE INSTEAD OF RS-232 (STANDARD) * DIP-SWITCH FOR ADDRESS INSTEAD OF SOLDERBRIDGE EA OPT-9/35V 1) EA OPT-RS4221) EA OPT-DIP61) ACCESSORIES * CABLE WITH 9-PIN D-SUB FEMALE PLUG FOR PC 1) 2) EA KV24-9B not available with SER308, SER408, SER3016 and SER4016 not available with SER082-C, SER204-4, SER242-B, SER3016 and SER4016 Zeppelinstr. 19 · D-82205 Gilching · Phone +49-8105-77 80 90 · Fax +49-8105-77 80 99 · www.lcd-module.de · [email protected] ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 2 General The Serials represents a complete LCD-Dotmatrix familiy with input circuit and frontal bezel. These LCD-modules also includes a RS-232 interface (or optional RS-422). The mounting is done through holes of the LCD-module, the data connection is made to a standard RS-232C/RS-422 interface. Transfer rate can be set by jumper on 300, 1200, 2400 or 9600 Baud. All cursor controls (line feed etc.) are performed automatically. All displays feature LED-backlight illumination. Matching frontal bezel with antiglare glass is included also. scheme Power SUPPLY / CONTRAST ADJUSTMENT Supply voltage is +5V, current consumption depends on type of display and its illumination (100-800 mA, see table on page 20). The Serials can be connected to power either by screw terminals or with RS-232 connector. Display contrast is adjustable by potentiometer. important: It is imperative that the polarity is correct. Even very brief polarity reversal can damage the entire operating unit immediately and irreparably. 9..35V Versorgung bei Displays im Snap-In Multiple Displays on a single RS-232C A single RS-232C can operate a number of displays. For that an individual adress must be assigned to each display. Commands "Select/Deselect" will target each individual display. Adresseinstellung per Lötbrücken 1) 2) Adresseinstellung über DIP-Schalter not available with SER308, SER408, SER3016 and SER4016 not available with SER082-C, SER204-4, SER242-B, SER3016 and SER4016 Adresseinstellung bei Displays im Snap-In ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 3 COMMANDS, DATA TRANSFER All incoming datas will be largely interpretated as ASCII datas. When display fills up, the characters automatically scroll to the top. CR/LF will be recognized and executed. FF (12d/$0C) clears the display. Cursor can be set manually by command i.e. "ESC O" (ESC=27d/$1B). TABLE OF COMMANDS Command Formfeed FF (dec.:12) Carriage Return CR (13) Linefeed LF (dec.:10) Cursor positioning Code ^L ^M ^J ESC O Cursor Form ESC C Display Mode ESC M Select / Deselect ESC S D n1 0 1 2 3 1 2 3 4 n2 adr Remark Clear screen and place cursor to home position (1,1) Set cursor into first column left hand Move cursor down to next line n1=column; n2=line; home-position (1,1) top left hand Hidden cursor Cursor in form of a flashing block Cursor as an underscore Cursor in form of a flashing block with an underscore Clear-mode; autoflow OFF Clear-mode; autoflow ON Scroll-mode; autoflow OFF Scroll-mode; autoflow ON Select interface adress adr=0..254; (adr 255=all) Deselect interface adress adr=0..254; (adr 255=all) after Reset 1,1 3 4 selected The 1-line, 2-line and 4-line displays offer beside standard-commands additional options: additional commands for 1..4 line displays Command Display Mode ESC M Convert Character Code ESC U Define character LED backlit on/off ESC ESC Z L Code 5 6 0 1 n1 8 x data... n1 Write output port ESC Y n1 Version Number ESC V Reset ESC R n2 Remark Overwrite-mode; autoflow OFF Overwrite-mode; autoflow ON no character code conversion convert character code to IBM-Code (for englisch/japanisch character set) n1=character no. (0..7); data = 8x bytes for new character LED backlit n1=0: off, n1=1: on; n1=2: invert; n1=3..255 n1/10 sec. on n1=0: Set all 6 output ports in accordance with n2 (=6-bit binary value) n1=1..8: Reset output port n1 (n2=0); set (n2=1); invert (n2=2) Shows the version number on the display Resets and re-initializes the display and controller. Before sending new data over the RS-232/RS-422 wait 500. after Reset 4 1 on all 1 The 8-line and 16-line displays offer beside standard-commands additional options: additional commands for 8- and 16-line displays Command Display Mode ESC Set letter type ESC Save actual settings Select / Deselect ESC ESC M N I B L P A Code 5 6 7 8 adr Remark Clear-mode; autoflow OFF Clear-mode; autoflow ON Scroll-mode; autoflow OFF Scroll-mode; autoflow ON Set standard type; black letters; bright background Set inverse letters; bright letters; black background Flashing letters; black letters flash on bright background Invers+flashing; bright letters flash on black background Saves cursorform, display-mode and font-type in EEPROM Assignes a new select/deselect adress (8 bit) to the interface after Reset 4 N ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 4 RS-232C Connection / Baud rates Connection to RS-232C or RS-422 interface is made on a 2x5 pin type socket. With cable EA KV24-9B (accessories not for RS-422) The Serials are ready to be connected directly to a PC. Transfer rate can be set by jumper on 300, 1200, 2400 or 9600 Baud. RS-232C socket (2x5 pins) Pin 1 Symbol Function Pin Symbol Function DCD connection to DSR and DTR 4 NC not connected 6 RXD data input 8 DTR connection to DSR and DCD 10 GND 0V VDD +5V 2 3 DSR connection to DCD and DTR 5 CTS 7 RTS 9 RXD5 CMOS CTS and RTS bridged close LB10+LB17 RS-422 socket (2x5 pins) Data format: Pin 1 3 If no jumper is set during power on, the display switches into self test mode and shows its character set. 5 7 9 Symbol Function VDD Pin Symbol Function +5V 2 Data In+ Receive Data 4 NC not connected HS In+ and HS Out+ HS Out+ bridged HS In+ 6 8 Data In- Receive Data NC not connected HS In- and HS OutHS Out- bridged 10 HS In- GND 0V If the operating unit is ordered together with the EA OPT-RS422 option, special RS-422 drivers are fitted. The pin assignment in the table on the right then applies. Incidentally, the same serial data with 5V level and CMOS logic is available at Pin 9. These level are suitable for direct connection to a µC. If these signal is used, the solder straps LB 10 + LB 17 must be closed! Connection for SER308,SER408,SER3016,SER4016 Connection for displays with snap-in Connection for 1- to 4-line diplays Connection for 1- to 4-line diplays with EA OPT-RS422 Connection for displays with snap-in with EA OPT-RS422 ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 5 Digital output 1) There are up to 6 digital outputs OUT1..OUT6. They share with the solder link for address setting (cannot be used with EA OPT-DIP6). When one or more outputs are used, the possibility for address set is limited automatically. All versions except EA S ERxxx-92 Displays with Snap-In case (EA SERxx-92) After Power-On all output are set to HIGH. Setting an output will be done by following command: 'ESC Y n1 n2' n1: Output no. 1, 2, 3, 4, 5 or 6 n2=0: Output set to LOW (0V); n2=1: Output set to HIGH (5V); n2=2: Invert output Application example1) Each output line provides a NPN transistor with about 50kOhm pull-up resistor; i.e. only LO level is able to supply about 10mA. In summary current for OUT1..OUT6 may not exceed 15mA. HIGH level is able to source up to 100µA only. Driving a higher load signal must be amplified by an external transistor or MOSFET. 1) not for SER308, SER408, SER3016 and SER4016 Self defined character 1) 8 character (ASCII codes $00..$07) are presetted with " ", "±", "²", "³", "ß", "Ä", "Ö", "Ü" and can be redefined with the command "ESC Z n1 data...". After re-definition the presetted codes are no longer available. It makes sense to switch off the relocation of ASCII codes via command 'ESC U 0'. After power-on or reset the predefined codes are avaiable again. Example: ESC Z $00 $04 $04 $04 $04 $15 $0E $04 $00 After that, character code $00 is defined as an downside arrow. Note: For definition 8 data bytes are necesary. 1) character data bit value hex (dez) 16 8 4 2 1 0 0 1 0 0 $04 (4) 0 0 1 0 0 $04 (4) 0 0 1 0 0 $04 (4) 0 0 1 0 0 $04 (4) 1 0 1 0 1 $15 (21) 0 1 1 1 0 $0E (14) 0 0 1 0 0 $04 (4) 0 0 0 0 0 $00 (0) not for SER308, SER408, SER3016 and SER4016: only the complete character set can be exchanged ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 6 Character set: 1- to 4-line displays All character listed beside are built-in for the 1- to 4-line displays. Character set: EA SER204-92HNLED The EA SER204-92HNLED do have a different character set. Character set: 8- and 16-line displays All 8- and 16-line displays EA SER308, SER408, SER3016 und SER4016 do provide the extended IBM character set (codes 32..255) incl. frame symbols. It is also possible to excange the character set totally (e.g. for cyrillic or special codes).This can be done together with the tools on EA DISK9708*). + Lower $0 $1 $2 $3 $4 $5 $6 $7 $8 $9 $A $B $C $D $E $F (0) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)(12)(13)(14)(15) Upper $20 (dez: 32) $30 (dez: 48) $40 (dez: 64) $50 (dez: 80) $60 (dez: 96) $70 (dez: 112) $80 (dez: 128) $90 (dez: 144) $A0 (dez: 160) $B0 (dez: 176) $C0 (dez: 192) $D0 (dez: 208) $E0 (dez: 224) $F0 (dez: 240) *) also in internet at http://www.lcd-module.de/deu/disk/disk9708.zip ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 7 EA SER081-92NLED incl. snap in housing EA 0092-KE 1x8,ZH 11.48mm in snap Panel cut out: 70,5+0,5 x 48,5+0,5 mm EA SER081-CNLED incl. frontal bezel EA 017-2UKE 1x8,ZH 10.8mm EA SER161-DNLED incl. frontal bezel EA 017-1UKE 1x16,ZH 6.6mm THE SERIALS Page 8 ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER161-ENLED incl. frontal bezel EA 017-6UKE 1x16,ZH 9.66mm EA SER082-CNLED incl. frontal bezel EA 017-8UKE 1x8,ZH 11.44mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER162-N3LW THE SERIALS Page 9 hite w / e u bl incl. frontal bezel EA 017-2UKE 2x16,ZH 5.55mm EA SER162-CNLED incl. frontal bezel EA 017-1UKE 2x16,ZH 4.35mm EA SER162-NLED incl. frontal bezel EA 017-2UKE 2x16,ZH 5.55mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 10 EA SER162-NLW hite w / e u bl incl. frontal bezel EA 017-2UKE 2x16,ZH 5.55mm EA SER162-BNLED incl. frontal bezel EA 017-12UKE 2x16,ZH 9.66mm EA SER162-BNLW incl. frontal bezel EA 017-12UKE 2x16,ZH 9.66mm white / e u l b ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER162-92NLED THE SERIALS Page 11 incl. snap in housing EA 0092-KE 2x16,ZH 6.68mm in snap Panel cut out: 70,5+0,5 x 48,5+0,5 mm EA SER202-NLED incl. frontal bezel EA 017-7UKE 2x20, ZH 5.55mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 12 EA SER202-NLW white / e u l b EA SER202-BHNLED EA SER202-CNLW incl. frontal bezel EA 017-7UKE 2x20, ZH 5.55mm without frontal bezel 2x20,ZH 9.2mm 2x20,ZH 12.7mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER242-NLED EA SER242-BNLED EA SER402-NLED THE SERIALS Page 13 incl. frontal bezel EA 017-14UKE 2x24,ZH 5.55mm without frontal bezel 2x24,ZH 9.66mm incl. frontal bezel EA 017-4UKE 2x40,ZH 5.55mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 14 EA SER402-NLW hite w / e u bl EA SER164-NLED EA SER204-92HNLED in snap Panel cut out: 70,5+0,5 x 48,5+0,5 mm incl. frontal bezel EA 017-4UKE 2x40,ZH 5.55mm incl. frontal bezel EA 017-8UKE 4x16,ZH 4.75mm incl. snap in housing EA 0092-KE 4x20,ZH 3.73mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 15 EA SER204-4NLED without frontal bezel 4x20,ZH 4.03mm EA SER204-NLED incl. frontal bezel EA 017-9UKE 4x20,ZH 4.75mm EA SER204-NLW incl. frontal bezel EA 017-9UKE 4x20,ZH 4.75mm hite w / e u bl THE SERIALS Page 16 ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER204-BNLED incl. frontal bezel EA 017-25KE 4x20,ZH 9.2mm EA SER404-HNLED incl. frontal bezel EA 017-13UKE 4x40,ZH 4.89mm EA SER404-NLW incl. frontal bezel EA 017-13UKE 4x40,ZH 4.89mm hite w / e blu ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. EA SER308-NLED / SER408-NLED THE SERIALS Page 17 incl. frontal bezel EA 017-10UKE 8x30 bold / 8x40,ZH 4.2mm THE SERIALS Page 18 EA SER3016-NLED / SER4016-NLED ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. without frontal bezel 16x30 bold / 16x40,ZH 3.55mm ATTENTION CAUTION! Use ESD precautionary procedures Electrostatic sensitive components handling precautions! ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 19 FRONTAL BEZEL / DIMENSIONS Drawing shows the nose piece for frontal bezels EA 017-xxUKE; EA 017-xxKE have a rim on full circumference. Display type Viewing area Outside dim. A B EA SER081-CNLED EA SER161-DNLED EA SER161-ENLED 60,0 63,5 98,5 14,8 12,8 12,8 EA SER162-N3LW EA SER162-CNLED 60,0 63,5 14,8 12,8 C D 1 line displays 76,0 27,0 79,5 25,0 114,5 25,0 2 line displays 76,0 27,0 79,5 25,0 EA SER162-NLED EA SER162-NLW 60,0 14,8 76,0 97,4 22,4 81,5 EA SER162-BNLED EA SER162-BNLW EA SER202-NLED EA SER202-NLW EA SER242-NLED EA SER402-NLED EA SER402-NLW EA SER164-NLED EA SER204-NLED EA SER204-NLW EA SER204-BNLED EA SER404-NLED EA SER404-NLW Mounting size Frontal Bezel E F G 66,2 69,7 104,7 21,2 19,2 19,2 71,0 74,5 109,5 EA 017-2U EA 017-1U EA 017-6U 66,2 69,7 21,2 19,2 71,0 74,5 EA 017-2U EA 017-1U 27,0 66,2 21,2 71,0 EA 017-2U 113,4 34,6 103,6 28,8 108,4 EA 017-12U 17,2 97,5 29,4 87,7 23,6 92,5 EA 017-7U 92,0 14,8 108,0 27,0 98,4 21,2 103,0 EA 017-14U 153,0 14,8 169,0 27,0 159,2 21,2 164,0 EA 017-4U 60,8 24,2 4 line displays 76,8 36,4 67,0 30,6 71,8 EA 017-8U 75,0 24,2 91,0 36,4 81,2 30,6 86,0 EA 017-9U 121,0 41,5 137,0 53,7 127,2 47,9 132,0 EA 017-25 145,0 28,0 161,0 40,2 151,2 34,4 156,0 EA 017-13U 137,2 44,4 142,0 EA 017-10U 8 line displays EA SER308-NLED EA SER408-NLED 131,0 38,0 147,0 50,2 Dimensions in mm ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice. Printing and typographical errors reserved. THE SERIALS Page 20 All Serials Overview Serial displays with RS-232 and LED backlight Ordering information Lines x Char. Char. height Module dimension Viewing area W H Bezel D W H 1 line displays Cutout bezel W H Keypad EA OPTCurrent NeW ! TAST5x5 typ. EA SER081-92NLED 1 x8 11.48 77.0 54.0 26.0 56.5 22.0 0092-KE 70.5 48.5 100 EA SER081-CNLED 1 x8 10.8 84.0 44.0 26.0 61.0 15.8 017-2UKE 66.2 21.2 30 optional EA SER161-DNLED 1 x 16 6.56 80.0 36.0 27.0 64.5 16.0 017-1UKE 69.7 19.2 100 optional EA SER161-ENLED 1 x 16 9.66 122.0 33.0 27.0 99.0 13.0 2 line displays 017-6UKE 104.7 19.2 170 optional EA SER082-CNLED 2 x8 11.44 84.0 44.0 27.5 63.0 25.0 017-8UKE 67.0 30.6 90 optional EA SER162-N3LW 2 x 16 5.55 80.0 36.0 27.0 64.5 16.0 017-2UKE 66.2 21.2 40 EA SER162-CNLED 2 x 16 4.35 80.0 36.0 27.0 64.5 13.8 017-1UKE 69.7 19.2 90 optional EA SER162-NLED 2 x 16 5.55 84.0 44.0 29.0 61.0 15.8 017-2UKE 66.2 21.2 120 optional EA SER162-NLW 2 x 16 5.55 84.0 44.0 27.0 64.5 16.0 017-2UKE 66.2 21.2 40 blue EA SER162-92NLED 2 x 16 6.68 77.0 54.0 26.0 56.5 22.0 0092-KE 70.5 48.5 100 Snap-In EA SER162-BNLED 2 x 16 9.66 122.0 44.0 29.0 99.0 24.0 017-12UKE 103.6 28.8 360 EA SER162-BNLW 2 x 16 9.66 122.0 44.0 29.0 99.0 24.0 017-12UKE 103.6 28.8 65 EA SER202-NLED 2 x 20 5.55 116.5 39.0 29.0 85.0 18.6 017-7UKE 87.7 23.6 210 EA SER202-NLW 2 x 20 5.55 116.5 39.0 26.0 85.0 18.6 017-7UKE 87.7 23.6 40 EA SER202-BHNLED 2 x 20 9.2 146.0 43.0 29.0 123.0 23.0 - 127.2 28.4 270 EA SER202-CNLW 2 x 20 12.7 190.0 54.0 29.0 149.0 31.0 - - - 100 EA SER242-NLED 2 x 24 5.55 118.0 36.0 29.0 93.5 15.8 017-14UKE 98.4 21.2 150 optional EA SER242-BNLED 2 x 24 9.66 208.0 40.0 29.0 178.0 23.0 - - - 190 optional EA SER402-NLED 2 x 40 5.55 182.0 33.5 29.0 154.1 15.3 017-4UKE 159.2 21.2 150 EA SER402-NLW 2 x 40 5.55 182.0 33.5 27.0 154.1 15.3 4 line displays 017-4UKE 159.2 21.2 40 EA SER164-NLED 4 x 16 4.75 87.0 60.0 29.0 61.8 25.4 017-8UKE 67.0 30.6 220 EA SER204-92HNLED 4 x 20 3.73 77.0 54.0 26.0 56.5 22.0 0092-KE 70.5 48.5 100 EA SER204-4NLED 4 x 20 4.03 80.8 47.0 29.0 60.0 22.0 - - - 90 EA SER204-NLED 4 x 20 4.75 98.0 60.0 29.0 76.0 25.2 017-9UKE 81.2 30.6 260 EA SER204-NLW 4 x 20 4.75 98.0 60.0 29.0 76.0 25.2 017-9UKE 81.2 30.6 45 EA SER204-BNLED 4 x 20 9.2 146.0 62.5 29.0 123.0 42.5 017-25KE 127.2 47.9 810 EA SER404-HNLED 4 x 40 4.89 190.0 54.0 29.0 147.0 29.5 017-13UKE 151.2 34.4 440 EA SER404-NLW 4 x 40 4.89 190.0 54.0 29.0 147.0 29.5 8 line displays 017-13UKE 151.2 34.4 75 EA SER308-NLED 8 x 30 29.0 40.2 017-10UKE 137.2 44.4 300 EA SER408-NLED 8 x 40 29.0 134.0 40.2 16 line displays 017-10UKE 137.2 44.4 300 EA SER3016-NLED 16 x 30 EA SER4016-NLED 16 x 40 4.2 bold 180.0 65.0 4.2 180.0 65.0 3.6 bold 144.0 104.0 29.0 3.6 144.0 104.0 29.0 134.0 114.0 64.0 --- - - 700 114.0 64.0 --- - - 700 Snap-In blue optional optional optional blue optional optional blue optional optional blue optional optional blue optional optional Snap-In optional optional blue optional optional optional blue optional Dimensions in mm Current in mA ATTENTION CAUTION! Use ESD precautionary procedures Electrostatic sensitive components handling precautions! Zeppelinstr. 19 · D-82205 Gilching · Phone +49-8105-77 8090 · Fax +49-8105-77 80 99 · www.lcd-module.de · [email protected]