350 MA CONSTANT-CURRENT LED DRIVER FSP3300 FEATURES z z z z z z z z z z No external component required 350mA constant sink current Output short circuit protection Low dropout voltage Low quiescent current Build-in thermal protection Supply voltage range 2.7V~7V 2KV HBM ESD protection Advanced CMOS process SOT89 and TO252 package The FSP3300 is a low dropout current regulator rated for 350mA constant sink current. The low quiescent current and low dropout voltage is achieved by advanced CMOS process PIN CONFIGURATION (1) SOT89 GENERAL DESCRIPTION APPLICATIONS z Power LED driver (2) TO252 (Top View) (Top View) 3 2 Symbol 1 2 3 1/7 1 2 3 OUT GND VDD Name OUT GND VDD 1 VDD GND OUT Descriptions Output pin, connect to load Ground Power supply BLOCK DIAGRAM 2007-1-25 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Rating Unit VDD Input Voltage 2.7 to 7 V VLEDn Output Voltage 2.7 to 7 V TJ Maximum Junction Temperature 150 ℃ ℃ Tstg Storage Temperature Range -40~+150 Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. ELECTRICAL CHARACTERISTICS (VDD=3.7V, TA=25℃, UNLESS OTHERWISE NOTED) Symbol Parameter Test Conditions ISINK Output Sink Current VOUT=0.2V Load Regulation VOUT=0.2V to 3V Line Regulation VDD=3V to 6V , VOUT=0.2V VOUTL Output Dropout Voltage IDD Supply Current Consumption Note: Output dropout voltage: 90% ×IOUT@ VOUT=200mV Typ. Max. Unit 305 350 390 5 5 mA mA/V mA/V mV µA 120 200 Apply Pin OUT VDD Recommended Operating Conditions Symbol VDD IOUT Ta Min. Parameter Supply Voltage Output Sink Current Operating free-air temperature range Min. 2.7 -40 Typ. Max. 6 400 +85 Unit V mA ℃ Power Dissipation Table θJA Derating factor (mW/℃) Power rating (mW) Power rating (mW) Power rating (mW) TA≤25℃ (℃/W) TA=70℃ TA=85℃ TA≥25℃ PK 71 14.1 1763 1128 916 Note: Junction Temperature Calculation: TJ=TA+(PD×θJA). PD: Power Dissipation, TA: Ambient temperature, θJA: Thermal Resistance-Junction to Ambient. The θJA numbers are guidelines for the thermal performance of the device/PC-board system. All of the above assume no ambient airflow. Package 2/7 2007-1-25 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 TYPICAL APPLICATIONS CIRCUIT (1) Typical Application Circuit Supply Voltage 2.7V to 7.0V 1 3 VDD OUT 2 GND Note: 1. The supply voltage should be larger than the forward voltage of the LED by 0.15V. VDD≥VLEDF+0.15 In the application of VDD= VLEDF+0.15, the chip works in the max efficiency and min power dissipation (2) Typical Application Circuit for Larger Current Supply Voltage 4*Battery ≥6V 1 3 VDD OUT 1 2 GND 3 VDD OUT 2 GND Note: The FSP3300 can be parallel connected to get larger driver current (about 700mA) for 3W LED. At this application, the supply voltage should be 6V at least for 3W LED. To minimize the chip power dissipation, there should be a diode connected between supply to VDD of the chip. The forward voltage of the diode should be less than 3.3V. APPLICATION INFORMATION The maximum power dissipation on regulator: PD(MAX)=VOUT(MAX)×IOUT(NOM)+VIN(MAX) ×IQ VOUT(MAX =the maximum voltage on output pin IOUT(NOM)=the nominal output current IQ =the quiescent current the regulator consumes at VIN(MAX =the maximum input voltage Thermal consideration: The FSP3300 have internal power and thermal limiting circuitry designed to protect the device under overload conditions. However maximum junction temperature ratings should not be exceeded under continuous normal load conditions. The thermal protection circuit of FSP3300 prevents the device from damage due to excessive power dissipation. When the device temperature rises to approximately 120℃, the regulator will be turned off. When power consumption is over about 700mW (SOT89-3L package at TA=70℃), additional heat sink is required to control the junction temperature below 120℃. The junction temperature is: TJ=PD(θJT+θCS +θSA)+TA PD: Dissipation power θJT: Thermal resistance from the junction to the mounting tab of the package θCS: Thermal resistance through the interface between the IC and the surface on which it is mounted. (typically, θCS≤1.0℃/W) 3/7 2007-1-25 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 θSA: Thermal resistance from the mounting surface to ambient (thermal resistance of the heat sink) If PC Board copper is going to be used as a heat sink, below table can be used to determine the appropriate size of copper foil required. For multi-layered PCB, these layers can also be used as a heat sink, They can be connected with several through hole vias. PCB θSA (℃/W) PCB heat sink size (mm2) 45 1000 38 1500 33 2000 27 3000 24 4000 21 5000 0.17 0.16 0.15 0.14 0.13 0.12 0.11 0.10 Quiescent Current vs Supply Voltage IQ(mA) IQ(mA) TYPICAL PERFORMANCE CHARACTERISTICS OUT(mA) 4/7 59 500 2 2.5 3 VIN(V) 3.5 4 0.22 0.20 0.18 0.16 0.14 0.12 0.10 20 Quiescent Current vs Temperature 30 40 50 60 70 80 Temperature(℃) Output Current vs Out-dropout Voltage 140 120 100 80 60 40 20 0 0.01 0.1 1 10 OUT-DROPOUT(V) 2007-1-25 90 100 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 ORDERING INFORMATION FSP3300X X X Package: Y: SOT89 D: TO252 Packing: Blank: Tube or Bulk A: Tape & Reel Temperature Grade: D: -40~85℃ MARKING INFORMATION (1) SOT89 (2) TO252 Logo Logo LAYMX FSP3300 Internal Code Date Code: Y: Year (1=2001) M: Month (1~9, O,N, D) Part Number: FSP3300 5/7 Part Number YYWWXX Internal Code Date Code: YY: Year (01=2001) WW: Nth week (01~52) 2007-1-25 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 PACKAGE INFORMATION (1) SOT89 D1 HE E 2.7 1.7 e1 1.3 L 1.9 0.4 1.5 0.9 e Land Patten Recommendation (Unit :mm) 5°(2х) 8°(2х) C A D b Symbol A b b1 C D D1 e e1 E HE L 6/7 b1 Min. 1.40 0.36 0.41 0.35 4.40 1.40 2.90 1.45 2.35 3.94 0.80 b Dimensions In Millimeters Nom. 1.50 0.42 0.47 0.39 4.50 1.60 3.00 1.50 2.48 Max. 1.60 0.48 0.53 0.43 4.60 1.75 3.10 1.55 2.60 4.25 1.20 Min. 0.055 0.014 0.016 0.014 0.173 0.055 0.114 0.057 0.093 0.155 0.031 Dimensions In Inches Nom. 0.059 0.016 0.043 0.015 0.177 0.062 0.118 0.059 0.098 2007-1-25 Max. 0.063 0.018 0.051 0.017 0.181 0.069 0.122 0.061 0.102 0.167 0.047 350 MA CONSTANT-CURRENT LED DRIVER FSP3300 (2) TO252 5.6 E 7.2 2.25 L1 2.0 D 11.0 5.6 L2 b2 1.2 b e Land Pattern Recommendation (Unit : mm) e1 C A1 C1 L A H SEATING PLANE SEE NOTE2 Notes: 1. JEDEC Outline:TO-252 AB 2. Mils suggested for positive contact at mounting Symbol A A1 b b2 C C1 D E e e1 H L L1 L2 7/7 Min. 2.18 1.02 5.20 0.46 0.46 5.33 6.35 9.00 0.51 0.64 1.52 Dimensions In Millimeters Nom. Max. 2.29 2.39 1.15 1.27 0.61TYP. 5.35 5.50 0.52 0.58 0.52 0.58 5.57 5.80 6.58 6.80 2.25BSC. 4.50BSC. 9.70 10.40 0.83 1.78 1.02 2.03 Min. 0.086 0.040 0.205 0.018 0.018 0.210 0.250 0.354 0.020 0.025 0.060 Dimensions In Inches Nom. 0.090 0.045 0.024TYP. 0.211 0.020 0.020 0.219 0.259 0.089BSC. 0.177BSC. 0.382 0.033 0.070 2007-1-25 Max. 0.094 0.050 0.217 0.023 0.023 0.228 0.268 0.409 0.040 0.080