MC78L00A Series, NCV78L00A 100 mA Positive Voltage Regulators The MC78L00A Series of positive voltage regulators are inexpensive, easy−to−use devices suitable for a multitude of applications that require a regulated supply of up to 100 mA. Like their higher powered MC7800 and MC78M00 Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the MC78L00 devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode−resistor combination, as output impedance and quiescent current are substantially reduced. Features • • • • • • • • Wide Range of Available, Fixed Output Voltages Low Cost Internal Short Circuit Current Limiting Internal Thermal Overload Protection No External Components Required Complementary Negative Regulators Offered (MC79L00A Series) Pb−Free Packages are Available NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Q3 15k Input Q11 Q5 Q12 Q1 Q10 5.0k 3.8k Q4 1.9k 1.2k Q6 Output 0-25k 19k 2.2k Q8 Q2 2.85k Q7 420 1.0k Ground Figure 1. Representative Schematic Diagram Input MC78LXXA Cin* 0.33 mF TO−92 P SUFFIX CASE 029 2 3 BENT LEAD TAPE & REEL AMMO PACK Pin: 1. Output 2. Ground 3. Input 8 1 SOIC−8* D SUFFIX CASE 751 *SOIC−8 is an internally modified SO−8 package. Pins 2, 3, 6, and 7 are electrically common to the die attach flag. This internal lead frame modification decreases package thermal resistance and increases power dissipation capability when appropriately mounted on a printed circuit board. SOIC−8 conforms to all external dimensions of the standard SO−8 package. VOUT 1 8 VIN GND 2 7 GND GND 3 6 GND NC 4 5 NC (Top View) See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. CO** 0.1 mF DEVICE MARKING INFORMATION A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. * Cin is required if regulator is located an appreciable distance from power supply filter. ** CO is not needed for stability; however, it does improve transient response. January, 2010 − Rev. 15 3 STRAIGHT LEAD BULK PACK ORDERING INFORMATION Output Figure 2. Standard Application © Semiconductor Components Industries, LLC, 2010 1 12 PIN CONNECTIONS Q9 C Z1 3.0 http://onsemi.com 1 See general marking information in the device marking section on page 16 of this data sheet. Publication Order Number: MC78L00A/D MC78L00A Series, NCV78L00A ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage (5.0 V−9.0 V) Input Voltage (12 V−18 V) Input Voltage (24 V) VI 30 35 40 Vdc Storage Temperature Range Tstg −65 to +150 °C Maximum Junction Temperature TJ 150 °C MSL 1 − ESD Capability, Human Body Model (Note 1) ESDHBM 2000 V ESD Capability, Machine Model (Note 1) ESDMM 200 V ESD Capability, Charged Device Model (Note 1) ESDCDM 2000 V Moisture Sensitivity Level Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114) ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115) ESD Charged Device Model tested per EIA/JES D22/C101, Field Induced Charge Model. THERMAL CHARACTERISTICS Rating Symbol Value Unit PD Internally Limited W Thermal Characteristics, TO−92 Thermal Resistance, Junction−to−Ambient RqJA 200 °C/W Thermal Characteristics, SOIC8 Thermal Resistance, Junction−to−Ambient RqJA Refer to Figure 8 °C/W Package Dissipation 2. Thermal Resistance, Junction−to−Ambient depends on P.C.B. Copper area. See details in Figure 8. Thermal Resistance, Junction−to−Case is not defined. SOIC 8 lead and TO-92 packages that do not have a heat sink like other packages may have. This is the reason that a Theta JC is never specified. A little heat transfer will occur through the package but since it is plastic, it is minimal. The majority of the heat that is transferred is through the leads where they connect to the circuit board. http://onsemi.com 2 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 10 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB, NCV78L05A), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L05AC, AB, NCV78L05A Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 4.8 5.0 5.2 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 7.0 Vdc ≤ VI ≤ 20 Vdc 8.0 Vdc ≤ VI ≤ 20 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (7.0 Vdc ≤ VI ≤ 20 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 10 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (8.0 Vdc ≤ VI ≤ 20 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − 55 45 150 100 − − 11 5.0 60 30 4.75 4.75 − − 5.25 5.25 − − 3.8 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 40 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 8.0 Vdc ≤ VI ≤ 18 V, TJ = +25°C) RR 41 49 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) NOTE: NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 3 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 14 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L08AC, AB Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 7.7 8.0 8.3 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 10.5 Vdc ≤ VI ≤ 23 Vdc 11 Vdc ≤ VI ≤ 23 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (10.5 Vdc ≤ VI ≤ 23 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 14 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (11 Vdc ≤ VI ≤ 23 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − 20 12 175 125 − − 15 8.0 80 40 7.6 7.6 − − 8.4 8.4 − − 3.0 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 60 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 12 V ≤ VI ≤ 23 V, TJ = +25°C) RR 37 57 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) ELECTRICAL CHARACTERISTICS (VI = 15 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L09AC, AB Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 8.6 9.0 9.4 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 11.5 Vdc ≤ VI ≤ 24 Vdc 12 Vdc ≤ VI ≤ 24 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (11.5 Vdc ≤ VI ≤ 24 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 15 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (11 Vdc ≤ VI ≤ 23 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − 20 12 175 125 − − 15 8.0 90 40 8.5 8.5 − − 9.5 9.5 − − 3.0 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 60 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 13 V ≤ VI ≤ 24 V, TJ = +25°C) RR 37 57 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 4 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 19 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L12AC, AB Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 11.5 12 12.5 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 14.5 Vdc ≤ VI ≤ 27 Vdc 16 Vdc ≤ VI ≤ 27 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (14.5 Vdc ≤ VI ≤ 27 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 19 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (16 Vdc ≤ VI ≤ 27 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − 120 100 250 200 − − 20 10 100 50 11.4 11.4 − − 12.6 12.6 − − 4.2 − 6.5 6.0 − − − − 1.5 0.1 mV Vdc mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 80 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 15 V ≤ VI ≤ 25 V, TJ = +25°C) RR 37 42 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) ELECTRICAL CHARACTERISTICS (VI = 23 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, − 40°C < TJ < +125°C (for MC78LXXAB), S 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L15AC, AB / NCV78L15A Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 14.4 15 15.6 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 17.5 Vdc ≤ VI ≤ 30 Vdc 20 Vdc ≤ VI ≤ 30 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (17.5 Vdc ≤ VI ≤ 30 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 23 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (20 Vdc ≤ VI ≤ 30 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − 130 110 300 250 − − 25 12 150 75 14.25 14.25 − − 15.75 15.75 − − 4.4 − 6.5 6.0 − − − − 1.5 0.1 mV Vdc mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 90 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 18.5 V ≤ VI ≤ 28.5 V, TJ = +25°C) RR 34 39 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 5 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 27 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0°C < TJ < +125°C, unless otherwise noted.) MC78L18AC Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 17.3 18 18.7 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 21.4 Vdc ≤ VI ≤ 33 Vdc 20.7 Vdc ≤ VI ≤ 33 Vdc 22 Vdc ≤ VI ≤ 33 Vdc 21 Vdc ≤ VI ≤ 33 Vdc Regline − 45 325 − 35 275 − − 30 15 170 85 Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (21.4 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (20.7 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA) (VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (22 Vdc ≤ VI ≤ 33 Vdc) (21 Vdc ≤ VI ≤ 33 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mV mV Vdc 17.1 − 18.9 17.1 − 18.9 − − 3.1 − 6.5 6.0 mA mA DIIB − − − − 1.5 0.1 Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 150 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 23 V ≤ VI ≤ 33 V, TJ = +25°C) RR 33 48 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 6 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 33 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0°C < TJ < +125°C, unless otherwise noted.) MC78L24AC Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 23 24 25 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 27.5 Vdc ≤ VI ≤ 38 Vdc 28 Vdc ≤ VI ≤ 80 Vdc 27 Vdc ≤ VI ≤ 38 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (28 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (27 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (28 Vdc ≤ VI = 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA) (27 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change (28 Vdc ≤ VI ≤ 38 Vdc) (1.0 mA ≤ IO ≤ 40 mA) DIIB mV − − − − 50 60 − 300 350 − − 40 20 200 100 mV Vdc 22.8 − 25.2 22.8 − 25.2 − − 3.1 − 6.5 6.0 − − − − 1.5 0.1 mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 200 − mV Ripple Rejection (IO = 40 mA, f = 120 Hz, 29 V ≤ VI ≤ 35 V, TJ = +25°C) RR 31 45 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 7 V I -V O , INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V) MC78L00A Series, NCV78L00A MC78L05AC Vout = 5.0 V TJ = 25°C 6.0 IO = 1.0 mA 4.0 IO = 40 mA IO = 100 mA 2.0 0 0 2.0 4.0 6.0 VI, INPUT VOLTAGE (V) 8.0 10 Figure 3. Dropout Characteristics IO = 70 mA 2.0 1.5 IO = 40 mA 1.0 IO = 1.0 mA Dropout of Regulation is defined as when VO = 2% of VO 0.5 0 0 25 4.0 3.8 3.6 3.4 3.2 MC78L05AC VI = 10 V VO= 5.0 V IO = 40 mA 3.0 125 Figure 4. Dropout Voltage versus Junction Temperature 4.0 MC78L05AC Vout = 5.0 V IO = 40 mA TJ = 25°C 3.0 2.0 1.0 0 0 0 25 50 75 100 TA, AMBIENT TEMPERATURE (°C) 125 0 5.0 10 15 20 25 VI, INPUT VOLTAGE (V) 35 170 10,000 No Heatsink ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ 110 100 RqJA = 200°C/W PD(max) to 25°C = 625 mW 75 100 125 TA, AMBIENT TEMPERATURE (°C) 150 Figure 7. Maximum Average Power Dissipation versus Ambient Temperature − TO−92 Type Package Graph represents symmetrical layout 90 L 70 2.0 oz. Copper L 2.4 2.0 1.6 1.2 3.0 mm 50 0.8 RqJA 30 0 10 20 30 40 0.4 50 L, LENGTH OF COPPER (mm) Figure 8. SOIC−8 Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length http://onsemi.com 8 2.8 PD(max) for TA = 50°C 130 1000 50 40 3.2 150 10 25 30 Figure 6. Input Bias Current versus Input Voltage R θ JA, THERMAL RESISTANCE JUNCTION‐TO‐AIR (° C/W) Figure 5. Input Bias Current versus Ambient Temperature PD , POWER DISSIPATION (mW) 50 75 100 TJ, JUNCTION TEMPERATURE (°C) 5.0 I IB , INPUT BIAS CURRENT (mA) I IB , INPUT BIAS CURRENT (mA) 4.2 2.5 PD, MAXIMUM POWER DISSIPATION (W) VO, OUTPUT VOLTAGE (V) 8.0 MC78L00A Series, NCV78L00A APPLICATIONS INFORMATION Design Considerations input bypass capacitor should be selected to provide good high−frequency characteristics to insure stable operation under all load conditions. A 0.33 mF or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended. The MC78L00A Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition. Internal Short Circuit Protection limits the maximum current the circuit will pass. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. The +20V MC78L15A 0.33mF Input 6 R IO Constant Current to Grounded Load 2 MC1741 3 + 4 0.33mF 6.5 20V The MC78L00 regulators can also be used as a current source when connected as above. In order to minimize dissipation the MC78L05C is chosen in this application. Resistor R determines the current as follows: 5.0 V IO = + IB R 10k 7 MC78L05A 0.33mF +VO 10k MPS A70 -VO MPS U55 Figure 10. ± 15 V Tracking Voltage Regulator +VI MC78LXXA 0.33mF IIB = 3.8 mA over line and load changes -VI For example, a 100 mA current source would require R to be a 50W, 1/2 W resistor and the output voltage compliance would be the input voltage less 7 V. 0.33mF +VO 0.1mF MC79LXXA 0.1mF -VO Figure 9. Current Regulator Figure 11. Positive and Negative Regulator http://onsemi.com 9 MC78L00A Series, NCV78L00A ORDERING INFORMATION Device Output Voltage Operating Temperature Range MC78L05ABD Package Shipping† SOIC−8 98 Units/Rail MC78L05ABDG SOIC−8 (Pb−Free) 98 Units/Rail NCV78L05ABDG* SOIC−8 (Pb−Free) 98 Units/Rail MC78L05ABDR2 MC78L05ABDR2G NCV78L05ABDR2* SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag MC78L05ABPG TO−92 (Pb−Free) 2000 Units/Bag NCV78L05ABPG* TO−92 (Pb−Free) 2000 Units/Bag NCV78L05ABDR2G* MC78L05ABP MC78L05ABPRA 5.0 V TJ = −40° to +125°C TO−92 2000 Tape & Reel MC78L05ABPRAG TO−92 (Pb−Free) 2000 Tape & Reel NCV78L05ABPRAG* TO−92 (Pb−Free) 2000 Tape & Reel MC78L05ABPRE TO−92 2000 Tape & Reel MC78L05ABPREG TO−92 (Pb−Free) 2000 Tape & Reel NCV78L05ABPREG* TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack MC78L05ABPRMG TO−92 (Pb−Free) 2000 Ammo Pack NCV78L05ABPRMG* TO−92 (Pb−Free) 2000 Ammo Pack NCV78L05ABPRPG* TO−92 (Pb−Free) 2000 Ammo Pack MC78L05ABPRM MC78L05ACD SOIC−8 98 Units/Rail MC78L05ACDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L05ACDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag MC78L05ACDR2G MC78L05ACP MC78L05ACPG MC78L05ACPRA MC78L05ACPRAG 5.0 V TJ = 0° to +125°C MC78L05ACPRE MC78L05ACPREG MC78L05ACPRM MC78L05ACPRMG MC78L05ACPRP MC78L05ACPRPG TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack *NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 MC78L00A Series, NCV78L00A ORDERING INFORMATION (continued) Operating Temperature Range Package Shipping† SOIC−8 98 Units/Rail MC78L08ABDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L08ABDR2 Device Output Voltage MC78L08ABD SOIC−8 2500 Tape & Reel MC78L08ABDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel NCV78L08ABDR2* SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack SOIC−8 98 Units/Rail MC78L08ACDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L08ACDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack NCV78L08ABDR2G* TJ = −40° to +125°C MC78L08ABP MC78L08ABPG MC78L08ABPRA MC78L08ABPRAG MC78L08ABPRP MC78L08ABPRPG MC78L08ACD 8.0 V MC78L08ACDR2G MC78L08ACP MC78L08ACPG MC78L08ACPRA TJ = 0° to +125°C MC78L08ACPRAG MC78L08ACPRE MC78L08ACPREG MC78L08ACPRP MC78L08ACPRPG http://onsemi.com 11 MC78L00A Series, NCV78L00A ORDERING INFORMATION (continued)(continued) Operating Temperature Range Package Shipping† SOIC−8 98 Units/Rail MC78L09ABDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L09ABDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack SOIC−8 98 Units/Rail MC78L09ACDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L09ACDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag Device Output Voltage MC78L09ABD MC78L09ABDR2G MC78L09ABPRA 9.0 V TJ = −40° to +125°C MC78L09ABPRAG MC78L09ABPRP MC78L09ABPRPG MC78L09ACD MC78L09ACDR2G 9.0 V TJ = 0° to +125°C MC78L09ACP MC78L09ACPG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 12 MC78L00A Series, NCV78L00A ORDERING INFORMATION (continued) Operating Temperature Range Package Shipping† SOIC−8 98 Units/Rail MC78L12ABDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L12ABDR2 Device Output Voltage MC78L12ABD SOIC−8 2500 Tape & Reel MC78L12ABDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel NCV78L12ABDG* SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag NCV78L12ABDR2* TJ = −40° to +125°C NCV78L12ABDR2G* MC78L12ABP MC78L12ABPG TO−92 2000 Ammo Pack MC78L12ABPRPG TO−92 (Pb−Free) 2000 Ammo Pack NCV78L12ABPG* TO−92 (Pb−Free) 2000 Units/Bag SOIC−8 98 Units/Rail SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack MC78L12ABPRP MC78L12ACD MC78L12ACDG 12 V MC78L12ACDR2 MC78L12ACDR2G MC78L12ACP MC78L12ACPG MC78L12ACPRA MC78L12ACPRAG TJ = 0° to +125°C MC78L12ACPRE MC78L12ACPREG MC78L12ACPRM MC78L12ACPRMG MC78L12ACPRP MC78L12ACPRPG *NCV78L12A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 13 MC78L00A Series, NCV78L00A ORDERING INFORMATION (continued) Operating Temperature Range Package Shipping† SOIC−8 98 Units/Rail MC78L15ABDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L15ABDR2 SOIC−8 2500 Tape & Reel MC78L15ABDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel NCV78L15ABDR2G* SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack SOIC−8 98 Units/Rail MC78L15ACDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L15ACDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack Device Output Voltage MC78L15ABD MC78L15ABP TJ = −40° to +125°C MC78L15ABPG MC78L15ABPRA MC78L15ABPRAG MC78L15ABPRP MC78L15ABPRPG 15 V MC78L15ACD MC78L15ACDR2G MC78L15ACP MC78L15ACPG TJ = 0° to +125°C MC78L15ACPRA MC78L15ACPRAG MC78L15ACPRP MC78L15ACPRPG *NCV78L15A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 14 MC78L00A Series, NCV78L00A ORDERING INFORMATION (continued) Device Output Voltage Operating Temperature Range MC78L18ABP TJ = −40° to +125°C MC78L18ABPG MC78L18ACP MC78L18ACPG MC78L18ACPRA MC78L18ACPRAG 18 V TJ = 0° to +125°C MC78L18ACPRM MC78L18ACPRMG MC78L18ACPRP MC78L18ACPRPG MC78L24ABP MC78L24ABPG TJ = −40° to +125°C NCV78L24ABPRPG* MC78L24ACP MC78L24ACPG 24 V MC78L24ACPRA MC78L24ACPRAG TJ = 0° to +125°C MC78L24ACPRP MC78L24ACPRPG Package Shipping† TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 15 MC78L00A Series, NCV78L00A MARKING DIAGRAMS SOIC−8 D SUFFIX CASE 751 8 1 8 8LxxA ALYWB G xx A L Y W B, C G 1 8LxxA ALYWC G = 05, 08, 09, 12, or 15 = Assembly Location = Wafer Lot = Year = Work Week = Temperature Range = Pb−Free Package TO−92 P SUFFIX CASE 029 MC78L zzABP ALYWWG G MC78L zzACP ALYWWG G 1 2 3 1 2 3 zz = 05, 08, 09, 12, 15, 18 or 24 A = Assembly Location L = Wafer Lot Y = Year WW = Work Week G = Pb−Free Package (Note: Microdot may be in either location) http://onsemi.com 16 MC78L00A Series, NCV78L00A PACKAGE DIMENSIONS SOIC−8 NB D SUFFIX CASE 751−07 ISSUE AJ −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 17 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 _ 8 _ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC78L00A Series, NCV78L00A PACKAGE DIMENSIONS TO−92 (TO−226) P SUFFIX CASE 29−11 ISSUE AM A B STRAIGHT LEAD BULK PACK R P L SEATING PLANE K D X X G J H V C SECTION X−X N 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. DIM A B C D G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --0.250 --0.080 0.105 --0.100 0.115 --0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --6.35 --2.04 2.66 --2.54 2.93 --3.43 --- N A R BENT LEAD TAPE & REEL AMMO PACK B P T SEATING PLANE G K D X X J V 1 C N SECTION X−X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. MILLIMETERS DIM MIN MAX A 4.45 5.20 B 4.32 5.33 C 3.18 4.19 D 0.40 0.54 G 2.40 2.80 J 0.39 0.50 K 12.70 --N 2.04 2.66 P 1.50 4.00 R 2.93 --V 3.43 --- ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 18 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your loca Sales Representative MC78L00A/D