Mean Well APC-16 16w single output switching power supply Datasheet

APC-16
16W Single Output Switching Power Supply
series
Features :
Constant current mode design
Universal AC input / Full range
Protections:Short circuit / Over current / Over voltage
Fully isolated plastic case
Small and compact size
Cooling by free air convection
Pass LPS
Suitable for LED lighting and moving sign applications
100% full load burn-in test
Low cost / High reliability
2 years warranty
F
SPECIFICATION
MODEL
APC-16-350
APC-16-700
RATED CURRENT
350mA
700mA
DC VOLTAGE RANGE
RATED POWER
12~48V
16.8W
9~24V
16.8W
RIPPLE & NOISE (max.) Note.2 300mVp-p
OUTPUT
VOLTAGE TOLERANCE Note.3
CURRENT ACCURACY
5.0%
5.0%
LINE REGULATION
1.0%
INPUT
3000ms, 200ms / 230VAC
HOLD UP TIME (Typ.)
20ms/230VAC
Note.4
90 ~ 264VAC
127 ~ 370VDC
47 ~ 63Hz
EFFICIENCY(Typ.)
84%
AC CURRENT
INRUSH CURRENT(max.)
0.3A/230VAC;0.5A/115VAC
Cold start 35A/115VAC,70A/230VAC
83%
0.25mA / 240VAC
50.4~ 60V
Protection type : Shut off o/p voltage, clamping by zener diode
-30 ~ 70
20 ~ 90% RH non-condensing
VIBRATION
SAFETY STANDARDS
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
-40 ~ +80
0.2%/
27.6~ 33.5V
(Refer to "Derating Curve")
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
, 10 ~ 95% RH
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Design refer to TUV EN60950-1, EN61347-2-13, UL8750
I/P-O/P:3.75KVAC
EMC EMISSION
I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55015,EN61000-3-2 Class A,EN61000-3-3
EMC IMMUNITY
Compliance to EN61547,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A
MTBF
1145.7K hrs min.
DIMENSION
77*40*29(L*W*H)
0.1Kg; 120pcs/14Kg/0.93CUFT
PACKING
NOTE
3000ms, 200ms / 115VAC at full load
12ms/115VAC at full load
FREQUENCY RANGE
PROTECTION OVER VOLTAGE
OTHERS
LPS
250mVp-p
SETUP, RISE TIME
LEAKAGE CURRENT
(Note 5)
SELV
3.0%
LOAD REGULATION
VOLTAGE RANGE
110
MIL-HDBK-217F (25 )
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristic for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name: APC-16-SPEC 2011-07-09
APC-16
16W Single Output Switching Power Supply
Mechanical Specification
series
Unit:mm
90
82.5
77
150 10
UL1569 18AWG
AC/N(Blue)
AC/L(Brown)
15.5
40
19
+V(Red)
-V(Black)
31
UL1569 20AWG
T case
150 10
29
T case: Max. Case Temperature
Block Diagram
I/P
fosc : 67KHz
EMI FILTER
POWER
SWITCHING
RECTIFIERS
RECTIFIERS
&
FILTER
+V
-V
DETECTION
CIRCUIT
PWM
CONTROL
Derating Curve
Static Characteristics
100
100
90
80
80
70
50
LOAD (%)
LOAD (%)
60
40
20
-30
0
10
20
30
40
50
AMBIENT TEMPERATURE ( )
60
70
(HORIZONTAL)
60
50
40
90
100
200
210
220
230
240
250
264
INPUT VOLTAGE (VAC) 60Hz
File Name: APC-16-SPEC 2011-07-09
Similar pages