CHENMKO ENTERPRISE CO.,LTD CHUMH42PT SURFACE MOUNT NPN Digital Silicon Transistor VOLTAGE 50 Volts CURRENT 30 mAmpere APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. FEATURE * Small surface mounting type. (SC-88/SOT-363) * High current gain. * Suitable for high packing density. * * * * SC-88/SOT-363 Low colloector-emitter saturation. High saturation current capability. Two CHDTC144W transistors in one package. Built in bias resistor(R1=47kΩ, R2=22k ,Typ. ) (1) (6) 0.65 1.2~1.4 2.0~2.2 0.65 (4) 0.15~0.35 (3) 1.15~1.35 0.8~1.1 0.08~0.15 CIRCUIT 3 R1 R2 0~0.1 0.1 Min. 1 2.15~2.45 R2 R1 4 6 SC-88/SOT-363 Dimensions in millimeters LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC Supply voltage − 50 V VIN Input voltage -10 +40 V − 30 − 100 − 200 mW O C IO DC Output current IC(Max.) Tamb ≤ 25 OC, Note 1 mA PTOT Total power dissipation TSTG Storage temperature −55 +150 TJ Junction temperature − 150 O C Thermal resistance − 140 O C/W RθJ-S Note 1. Transistor mounted on an FR4 printed-circuit board. junction - soldering point 2006-07 RATING CHARACTERISTIC ( CHUMH42PT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIoff) Input off voltage IO=100uA; VCC=5.0V 0.8 − − V VI(on) Input on voltage IO=2mA; VO=0.3V − − 3.0 V VO(on) Output voltage IO=10mA; II=0.5mA − 0.1 0.3 V II Input current VI=5V − − 0.16 mA IC(off) Output current VI=0V; VCC=50V − − 0.5 uA hFE DC current gain IO=5mA; VO=5.0V 56 − − R1 Input resistor 61.1 KΩ Resistor ratio Transition frequency 32.9 0.37 − 47 R2/R1 fT 0.47 250 0.57 − MHz Note 1.Pulse test: tp≤300uS; δ≤0.02. IE=-5mA, VCE=10.0V f=100MHz = RATING CHARACTERISTIC CURVES ( CHUMH42PT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) 100 Fig.2 Output current vs. input voltage (OFF characteristics) 10m 50 5m 20 2m 1m 10 5 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) VO= 0.3V Ta=100OC 25OC -40 OC 2 1 500m VCC= 5V Ta=100OC 100u -40 OC 10u 200m 100m 100u 25OC 1m 1u 100m 10m 0 OUTPUT CURRENT : IO (A) Fig.3 DC current gain vs. output current 1k 1 VO = 5V Ta=100OC 25OC -40OC 50 20 10 5 2 1 100u 3.0 lO/lI=20 500m OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI 100 2.0 Fig.4 Output voltage vs. output current 500 200 1.0 INPUT VOLTAGE : VI(off) (V) 200m 100m 50m Ta=100OC 25OC -40 OC 20m 10m 5m 2m 1m 10m OUTPUT CURRENT : IO (A) 100m 1m 100u 1m 10m OUTPUT CURRENT : IO (A) 100m