Eutech EUA4890A 1 watt audio power amplifier Datasheet

EUA4890A
1 Watt Audio Power Amplifier
DESCRIPTION
FEATURES
The EUA4890A is an audio power amplifier designed for
portable communication device applications such as
mobile phone applications. The EUA4890A is capable of
delivering 1.0W of continuous average power to an 8Ω
BTL and with less than 1% distortion (THD+N) from a
5.0V power supply, and 350mW to a 8Ω BTL load from a
3V power supply.
The EUA4890A provides high quality audio while
requiring few external components and minimal power
consumption. It features a low-power shutdown mode,
which is achieved by driving the SHUTDOWN pin with
logic low.
The EUA4890A contains circuitry to prevent from ”pop
and click” noise that would otherwise occur during turn-on
and turn-off transitions.
For maximum flexibility, the EUA4890A provides an
externally controlled gain (with resistors), as well as an
externally controlled turn-on and turn-off times (with the
bypass capacitor).
z
z
z
z
z
z
z
z
z
z
z
z
z
Block Diagram
Figure1.
Sep. 2007
RoHS compliant and 100% lead(Pb)-free
APPLICATIONS
The EUA4890A is available in a 1.5mm×1.5mm WCSP
package.
DS4890A Ver 1.2
2.5-5.5V operation
65dB PSRR at 217Hz, VDD=5V
0.1µA ultra low current shutdown mode
Improved pop & click circuitry
No output coupling capacitors, snubber networks or
bootstrap capacitors required
Thermal shutdown protection
Unity-gain stable
External gain configuration capability
BTL output can drive capacitive loads
1
Mobile Phones
PDAs
Portable electronic devices
EUA4890A
Typical Application Circuit
Figure2. Audio Amplifier with Single –Ended Input
Figure3. Audio Amplifier with Differential Input
DS4890A Ver 1.2
Sep. 2007
2
EUA4890A
Pin Configurations
Package Type
Pin Configurations
(Top View)
WCSP-9
Pin Description
PIN
PIN
PIN
I/O
SHUTDOWN
1
C3
I
The device enters in shutdown mode when a low level is applied on this pin
BYPASS
2
C1
I
Bypass capacitor pin which provides the common mode voltage
+IN
3
A3
I
-IN
4
A1
I
VO1
5
A2
O
VDD
6
B3
I
Positive input of the first amplifier, receives the common mode voltage
Negative input of the first amplifier, receives the audio input signal. Connected to
the feedback resistor Rf and to the input resistor Rin.
Negative output of the EUA4890A. Connected to the load and to the feedback
resistor Rf
Analog VDD input supply.
GND
7
B1/B2
VO2
8
C2
DS4890A Ver 1.2
Sep. 2007
DESCRIPTION
Ground connection for circuitry.
O
Positive output of the EUA4890A.
3
EUA4890A
Ordering Information
Order Number
Package Type
Marking
Operating Temperature range
EUA4890AHIR1
WCSP
xxx
WA
-40 °C to 85°C
EUA4890A
□ □ □ □
Lead Free Code
1: Lead Free 0: Lead
Packing
R: Tape & Reel
Operating temperature range
I: Industry Standard
Package Type
H: WCSP
DS4890A Ver 1.2
Sep. 2007
4
EUA4890A
Absolute Maximum Ratings
Supply voltage, VDD
▓
Input voltage, VI ----------------------------------------------------------------------------
▓
ESD Susceptibility
▓
-65°C to 150°C
--------------------------------------------------------------------------------------------
Junction Temperature
▓
6V
-0.3 V to VDD +0.3V
Storage temperature rang, Tstg -------------------------------------------------------------------
▓
▓
--------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------
2kV
150°C
Thermal Resistance
θJA (WCSP) -------------------------------------------------------------------------------------------- 81.4°C/W
Electrical Characteristics VDD = 5V, TA = 25°C
Symbol
Parameter
IDD
Quiescent Power Supply Current
ISD
Shutdown Current
VSDIH
Shutdown Voltage Input High
VSDIL
Shutdown Voltage Input Low
VOS
Conditions
TWU
Wake-up time
TSD
Thermal Shutdown Temperature
THD+N Total Harmonic Distortion + Noise
PSRR
TSDT
Power Supply Rejection Ratio
Shutdown Time
DS4890A Ver 1.2
Sep. 2007
Unit
2.4
5
mA
VIN=0V, IO=0A, 8Ω load
2.5
5
mA
VSHUTDOWN=0V
0.1
2.0
µA
1.2
Output Offset Voltage
Output Power (8Ω)
EUA4890A
Typ
Max.
VIN=0V, IO=0A, No load
ROUT-GND Resistor Output to GND
PO
Min
7.0
THD=1%; f=1kHz
V
0.4
V
5
25
mV
8.5
9.7
kΩ
1.1
170
150
W
220
ms
170
°C
PO=0.4 Wrms; f=1kHz
0.15
%
Vripple=200mV sine p-p
Input Terminated with 10 ohms
to ground
65(f=217
Hz)
67(f=1kH
z)
dB
1.0
ms
8Ω load
5
55
EUA4890A
Electrical Characteristics VDD = 3V, TA = 25°C
Symbol
Parameter
IDD
Quiescent Power Supply Current
ISD
Shutdown Current
VSDIH
Shutdown Voltage Input High
VSDIL
VOS
Shutdown Voltage Input Low
Output Offset Voltage
Conditions
Output Power (8Ω)
Wake-up time
Thermal Shutdown Temperature
THD+N Total Harmonic Distortion + Noise
PSRR
Power Supply Rejection Ratio
EUA4890A
Max.
Typ
Unit
VIN=0V, IO=0A, No load
1.8
4
mA
VIN=0V, IO=0A, 8Ω load
VSHUTDOWN=0V
1.9
0.1
4
2.0
mA
µA
1.2
ROUT-GND Resistor Output to GND
PO
TWU
TSD
Min
THD=1%; f=1kHz
5
0.4
25
V
mV
7.0
8.5
9.7
kΩ
0.28
0.35
120
170
180
W
ms
°C
150
PO=0.15 Wrms; f=1kHz
Vripple=200mV sine p-p
Input Terminated with 10 ohms
to ground
V
45
0.15
65(f=217
Hz)
66(f=1kH
z)
%
dB
Electrical Characteristics VDD = 2.6V, TA = 25°C
Symbol
Parameter
Conditions
Min
EUA4890A
Typ
Max.
Unit
IDD
Quiescent Power Supply Current
VIN=0V, IO=0A, No load
1.7
mA
ISD
Shutdown Current
Output Power (8Ω)
Output Power (4Ω)
VSHUTDOWN=0V
THD=1%; f=1kHz
THD=1%; f=1kHz
0.1
0.25
0.32
µA
0.15
55(f=217
Hz)
56(f=1kH
z)
%
PO
THD+N Total Harmonic Distortion + Noise
PSRR
Power Supply Rejection Ratio
DS4890A Ver 1.2
Sep. 2007
PO=0.1Wrms; f=1kHz
Vripple=200mV sine p-p
Input Terminated with 10 ohms
to ground
6
W
dB
EUA4890A
Typical Operating Characteristics
Figure3.
DS4890A Ver 1.2
Figure4.
Figure5.
Figure6.
Figure7.
Figure8.
Sep. 2007
7
EUA4890A
Figure9.
Figure10.
Figure11.
Figure12.
Figure14.
Figure13.
DS4890A Ver 1.2
Sep. 2007
8
EUA4890A
Figure15.
Figure16.
Figue18.
Figure17.
Figure20.
Figure19.
DS4890A Ver 1.2
Sep. 2007
9
EUA4890A
Figure21.
Figure22.
Figure23.
Figure24.
Figure26.
Figure25.
DS4890A Ver 1.2
Sep. 2007
10
EUA4890A
Figure27.
Figure28.
Figure30.
Figure29.
Figure31.
DS4890A Ver 1.2
Sep. 2007
11
EUA4890A
Application Information
Bridged Configuration Explanation
The structure of the EUA4890A is basically composed of
two identical internal power amplifiers; the first one si
externally configurable with gain-setting resistors Rin and
Rf (the closed-loop gain is fixed by the ratios of theses
resistors) and the second is internally fixed in an inverting
unity-gain configuration by two resistors of 20kΩ. So the
load is driven differentially through OUTA and OUTB
outputs. This configuration eliminates the need for an
output coupling capacitor.
The differential-ended amplifier presents two major
advantages:
- The possible output power is four times larger (the
output swing is doubled) as compared to single-ended
amplifier under the same conditions.
- Output pins (OUTA and OUTB) are biased at the
same potential VDD/2, this eliminates the need for an
output coupling capacitor required with a
single-ended amplifier configuration.
The differential closed loop-gain of the amplifier is
given by Avd=
2×
R
f = Vorms
R
Vinrms
in
Power Dissipation
Power dissipation is a major concern when designing a
successful amplifier, whether the amplifier is bridged or
single-ended. A direct consequence of the increased
power delivered to the load by a bridge amplifier is an
increase in internal power dissipation. Since the
EUA4890A has two operational amplifiers in one package,
the maximum internal power dissipation is 4 times that of
a single-ended amplifier. The maximum power dissipation
for a given application can be derived from the power
dissipation graphs of from equation1.
PDMAX = 4 * (VDD ) 2 /(2π 2 R L ) ------------(1)
It is critical that the maximum junction temperature TJMAX
of 150°C is not exceeded. TJMAX can be determine from
the power derating curves by using PDMAX and the PC
board foil area. By adding additional copper foil, the
thermal resistance of the application can be reduced,
resulting in higher PDMAX. Additional copper foil can be
added to any of the leads connected to the EUA4890A.If
TJMAX still exceeds 150°C, then additional changes must
be made. These changes can include reduced supply
voltage, higher load impedance, or reduced ambient
temperature. Internal power dissipation is a function of
output power.
DS4890A Ver 1.2
Sep. 2007
Proper Selection of External Components
The EUA4890A is unity-gain stable and requires no
external components besides gain-setting resistors, and
input coupling capacitor and proper bypassing capacitor
in the typical application.
Gain-Setting Resistor Selection (Rin and Rf)
Rin and Rf set the closed-loop gain of the amplifier.
In order to optimize device and system performance, the
EUA4890A should be used in low gain configurations.
The low gain configuration minimizes THD + noise
values and maximizes the signal to noise ratio, and the
amplifier can still be used without running into the
bandwidth limitations. Low gain configurations require
large input signals to obtain a given output power. Input
signals equal to or greater than 1Vrms are available from
sources such as audio codecs.
A closed loop gain in the range from 2 to 5 is
recommended to optimize overall system performance.
An input resistor (Rin) value of 20kΩ is realistic in most
of applications, and does not require the use of a too large
capacitor Cin.
Input Capacitor Selection (Cin)
The input coupling capacitor blocks the DC voltage at the
amplifier input terminal. This capacitor creates a
high-pass filter with Rin, the cut-off frequency is given by
fc =
1
2 * ∏ *R
in
*C
in
The size of the capacitor must be large enough to couple
in low frequencies without severe attenuation. However a
large input coupling capacitor requires more time to reach
its quiescent DC voltage (VDD/2) and can increase the
turn-on pops.
An input capacitor value between 0.1µ and 0.39µF
performs well in many applications (with Rin=22kΩ).
Bypass Capacitor Selection (Cby)
The bypass capacitor Cby provides half-supply filtering
and determines how fast the EUA4890A turns on.
This capacitor is critical component to minimize the
turn-on pop. A 1.0µF bypass capacitor value (Cin= <
0.39µF) should produce clickless and popless shutdown
transitions. The amplifier is still functional with a 0.1µF
capacitor value but is more susceptible to pop and click
noise. Thus, a 1.0µF bypassing capacitor is recommended.
Power Supply Bypassing (CS)
As with any amplifier, proper supply bypassing is critical
for low noise performance and high power supply
rejection. The capacitor location on both the bypass and
power supply pins should be as close to the device is
possible.
12
EUA4890A
Packaging Information
WCSP-9
SYMBOLS
A
A1
D
D1
E
E1
DS4890A Ver 1.2
Sep. 2007
MILLIMETERS
MIN.
MAX.
0.675
0.15
0.35
1.45
1.55
0.50
1.45
1.55
0.50
13
INCHES
MIN.
0.006
0.057
MAX.
0.027
0.014
0.061
0.020
0.057
0.061
0.020
Similar pages