MB3000ERW Low Cost, 1 x 2 Inch 30W, 2:1 Input Range DC/DC Converters Electrical Specifications Key Features: Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. • 30W Output Power Input Parameter • 2:1 Input Voltage Range Input Voltage Range Conditions Min. 24 VDC Input 18.0 48 VDC Input 36.0 24 VDC Input 48 VDC Input (Pi) Filter See Note 1 • 1,500 VDC Isolation • 11 Single Output Models Input Start Voltage • Efficiency to 89% Input Filter Start-Up Time • Compact 1 x 2 Inch Case Output • -40°C to +85°C Operation Parameter Output Voltage Accuracy Output Trim Range Line Regulation Load Regulation Ripple & Noise (20 MHz) Transient Recovery Time, See Note 3 Transient Response Deviation Output Power Protection Temperature Coefficient Output Short Circuit, See Note 4 • Industry Standard Pin-Out • Low Cost Conditions Typ. 24.0 48.0 17.8 35.8 Max. 36.0 75.0 18.0 36.0 10 Min. Units VDC VDC mS Typ. ±1.0 ±10 ±0.2 VIN = Min to Max IOUT = 10% to 100% ±0.5 See Note 2 50 300 25% Load Step Change ±3.0 120 130 ±0.02 Continuous (Autorecovery) Max. ±3.0 Conditions Max. Units VDC M pF kHz Max. +85 +105 +125 Units °C °C °C 95 % ±0.5 ±1.0 120 500 ±5.0 150 Units % % % % mV P - P µS % % %/°C General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency 60 Seconds 500 VDC 100 kHz/0.1V Min. 1,500 1,000 Typ. 1,000 300 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Ambient Case Min. -40 Typ. +25 -55 Free Air Convection RH, Non-condensing See Mechanical Diagram (Page 4)) Aluminum Alloy With Non-Conductive Base (UL94-V0) 0.78 Oz (22g) Remote On/Off MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Unit On Unit Off Off Idle Current Conditions See Note 5 See Note 5 Min. 3.0 0 Typ. Max. 40.0 1.2 1.0 Units VDC VDC mA Reliability Specifications Parameter MTBF Vibration Conditions Min. Typ. Max. MIL HDBK 217F, 25°C, Gnd Benign 1.0 10 - 55 Hz, 10G, 30 Min, on X, Y & Z Axis Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Conditions 24 VDC Input 48 VDC Input 1.5 mm From Case for 10 Sec Min. -0.7 -0.7 Typ. Max. 50.0 100.0 300 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Units VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Output Current (mA) Voltage Current Full-Load No-Load (VDC) (mA, Max) Current (mA, Min) Efficiency (%, Typ) Over Fuse Voltage Capacitive Rating Load Protection Slow-Blow (VDC Typ) (µF, Max) (mA) Nominal Range MB3024S-03ERW 24 18.0 - 36.0 960 120 3.3 6,000 600 87 3.96 6,800 2,000 MB3024S-05ERW 24 18.0 - 36.0 1,460 120 5.0 6,000 600 88 6.00 6,800 3,000 MB3024S-09ERW 24 18.0 - 36.0 1,440 20 9.0 3,333 333 88 10.8 680 3,000 MB3024S-12ERW 24 18.0 - 36.0 1,440 20 12.0 2,500 250 88 15.0 680 3,000 MB3024S-15ERW 24 18.0 - 36.0 1,440 20 15.0 2,000 200 89 18.0 680 3,000 MB3024S-24ERW 24 18.0 - 36.0 1,440 20 24.0 1,250 125 89 28.0 470 3,000 MB3048S-03ERW 48 36.0 - 75.0 500 80 3.3 6,000 600 87 3.96 6,800 1,000 MB3048S-05ERW 48 36.0 - 75.0 730 80 5.0 6,000 600 88 6.00 6,800 1,500 MB3048S-12ERW 48 36.0 - 75.0 720 20 12.0 2,500 250 89 15.0 680 1,500 MB3048S-15ERW 48 36.0 - 75.0 720 20 15.0 2,000 200 89 18.0 680 1,500 MB3048S-24ERW 48 36.0 - 75.0 720 20 24.0 1,250 125 88 28.0 470 1,500 Notes: 1. Start up time is measured at nominal input and with a constant resistive load. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 1 µF to 10 µF) be placed from the +VOUT to the -VOUT pins. 3. Transient recovery is measured to within a 1% error band for a load step change of 25%. 4. Short circuit protection is provided by a “hiccup mode” circuit. 5. If the on/off pin is left open, the unit operates. If it is grounded, the unit will shut off. 6. These units should not be operated with a load under 10% of full load. Operation at no-load will not damage the unit, but they may not meet all specifications. 7. These units should not be operated over +85°C. Exceeding +85°C may damage the unit. 8. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve, Output Voltage <5V External Trim Derating Curve, Output Voltage >5V External Trim Notes: On single output units, an external resistor can be used to adjust the converter output up/down by about 10%. The connection is shown in the diagram at left. The required resistor value is calculated by the formulas: Trim UP = RTRIM = A $-R2 - R3 R2 A Trim Down = RTRIM = A $-R1 - R3 R1 A Where A = VREF $ R1 VTRIM - VREF Where A = VTRIM VREF $ R2 VREF Where RTRIM = The value of the external trim resistor VTRIM = The amount of voltage adjustment required The value of R1, R2, R3 and VREF are given in the table below. 292 Page Street Ste D Stoughton, MA 02072 Output Trim Resistor Values Parameter R1 (k) R2 (k) R3 (k) VREF (V) 3.3 4.801 2.863 15.00 1.24 5.0 2.883 2.864 10.00 2.50 Output Voltage (VDC) 9.0 12 15 7.500 10.971 14.497 2.864 2.864 2.864 15.00 17.80 17.80 2.50 2.50 2.50 24 24.872 2.864 20.00 2.50 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com EMC Specifications Parameter Radiated Emissions Conducted Emissions ESD RS EFT Surge CS Voltage Dips Standard See Note 1 EN 55022 See Note 1 EN 55022 EN 61000-4-2 EN 61000-4-3 See Note 2 EN 61000-4-4 See Note 3 EN 61000-4-5 EN 61000-4-6 EN 61000-4-29 Class A Class A Criteria B; ±4 kV Contact Criteria A; 10V/m Criteria B; ±2 kV Criteria B; ±2 kV Criteria A; 3 Vrms Criteria B; 0% - 70% Notes: 1. All units are rated for EN 55022 (CE/RE) class A without external components. They will meet class B with the addition of the MDCFM-xxW (or a similar discrete filter circuit). Contact the factory for more information. 2. To meet the requirements of EN 61000-4-4 (±2 kV), external components are needed. This can be done discretely, or with the addition of the MDCFM-xxW. Contact the factory for more information. 3. To meet the requirements of EN 61000-4-5 (±2 kV), external components are needed. This can be done discretely, or with the addition of the MDCFM-xxW. Contact the factory for more information. Typical Connection The diagram above illustrates a typical connection of the MB3000ERW 5. Recommended values for components are: series for applications that require meeting EMC standards. The units do not Component 48 VIN 24 VIN require external components to operate as specified. Some notes on this MOV S14K35 S14K60 diagram (starting with the input circuit) are: L1 56 µH 56 µH 1. It is recommended that an external fuse be used. The recommended fuse is shown in the model chart on page 2. TVS SMCJ48A SMCJ90A 2. An external MOV is recommended on the input to protect the unit in the C1 330 µF/50V 330 µF/100V event of a surge. A recommended value is given in the table at right. C2, C3 4.7 µF/50V 2.2 µF/100V 3. An external TVS is recommended on the input to protect the unit in the L2 1.0 mH 1.0 mH event of a voltage spike. A recommended value is given in the table at CY1, CY2 1nF/2 kV 1nF/2 kV right. 4. The output filtering capacitor (C4) is a high frequency, low resistance C0 400 uF/200V 400 uF/200V electrolytic capacitor. Care must be taken in choosing this capacitor not to exceed the capacitive load specification for the unit. Voltage derating 6. Input noise and surge suppression modules are available for a number of MPD DC/DC power supplies. A connection for one of of capacitors should be 80% or above. these modules is illustrated in the typical board layout shown at the bottom of this page For pricing or full technical information, please contact the factory. Input Vout Output 7. In many applications simply Vin adding input/output capaci- (VDC) Capacitor (VDC) Capacitor tors will enhance the input 3.3 220 µF 24 100 µF surge protection and reduce 5.0 220 µF output ripple sufficiently. The 9.0 100 µF 100 µF input capacitor C1 and output 48 12 100 µF capacitor C4 shown in the 100 µF typical connection diagram above (& board layout 15 24 47 µF drawing below) illustrate their connection. Recommended capacitor values are given in the table. Typical Board Layout: With External Filter/Surge Components Typical Connection: With External Filter ModuleUnit MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 6 Function +Vin -Vin Remote On/Off +Vout -Vout Trim Adapter Plate Mechanical Dimensions: With Optional Heatsink All models of the MB3000x-xxERW series are available mounted on an adapter plate similar to the one pictured at left. The adapter plate makes it easier to mount the unit to a chassis or to a standard DIN rail. Please contact the factory for more information. For the heatsink option, add suffix “H” to the model number (i.e. MB3024S-05ERW-H) MicroPower Direct Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]