HCC/HCF4067B HCC/HCF4097B ANALOG MULTIPLEXER/DEMULTIPLEXER 4067B–SINGLE 16-CHANNEL 4097B–DIFFERENTIAL 8-CHANNEL . . . . .. . .. .. LOW ON RESISTANCE: 125Ω (typ.) OVER 15 Vp-p SIGNAL INPUT RANGE FOR VDD - VSS = 15V HIGH OFF RESISTANCE: CHANNEL LEAKAGE OF ±10pA (typ.) @ VDD - VSS = 10V MATCHED SWITCH CHARACTERISTICS: ∆RON = 5Ω (typ.) FOR VDD - VSS = 15V VERY LOW QUIESCENT POWER DISSIPATION UNDER A DIGITAL CONTROL INPUT AND SUPPLY CONDITIONS: 0.2µW (typ.) @ VDD -VSS = 10V BINARY ADDRESS DECODING ON CHIP QUIESCENT CURRENT SPECIFIED TO 20V FOR HCC DEVICE STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS 5V, 10V AND 15V PARAMETRIC RATINGS o INPUT CURRENT OF 100nA AT 18V AND 25 C FOR HCC DEVICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TENTATIVE STANDARD No 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF B SERIE CMOS DEVICES” EY (Plastic Package) F (Ceramic Package) M1 (Micro Package) C1 (Chip Carrier) ORDER CODES : HCC40XXBF HCF40XXBM1 HCF40XXBEY HCF40XXBC1 PIN CONNECTIONS 4067B September 1988 4097B 1/16 HCC/HCF4067B HCC/HCF4097B DESCRIPTION The HCC4067B, HCC4097B (extended temperature range) and HCF4067B, HCF4097B (intermediate temperature range) are monolithic integrated circuits available in 24-lead dual in line plastic or ceramic package. The HCC/HCF4067B and HCC/HCF4097B COS/MOS analog multiplexers/demultiplexers are digitally controlled analog switches having low ON impedance, low OFF leakage current and internal address decoding. in addition, the ON resistance is relatively constant over the full input-signal range. The HCC/HCF4067B ia a 16-channel multiplexer with four binary control inputs A, B, C, D, and an inhibit input, arranged so that any combination of the inputs selects one switch. The HCC/HCF4097 is a differential 8-channel multiplexer having three binary control inputs A, B, C, and an inhibit input. The inputs permit selection of one FUNCTIONAL DIAGRAM For 4067B 2/16 For 4097B HCC/HCF4067B HCC/HCF4097B LOGIC DIAGRAM For 4067B 3/16 HCC/HCF4067B HCC/HCF4097B LOGIC DIAGRAM For 4097B 4/16 HCC/HCF4067B HCC/HCF4097B TRUTH TABLES FOR HCC/HCF4067B TRUTH TABLE FOR HCC/HCF4097B A B C D INH SELECTED CHANNEL A B C INH SELECTED CHANNEL X 0 X 0 X 0 X 0 1 0 None 0 X 0 X 0 X 0 1 0 None 0X 0Y 1 0 0 0 0 1 1 0 0 0 1X 1Y 0 1 1 1 0 0 0 0 0 0 2 3 0 1 1 1 0 0 0 0 2X 2Y 3X 3Y 0 0 1 0 0 4 0 0 1 0 4X 4Y 1 0 1 0 0 5 1 0 1 0 5X 5Y 0 1 1 0 0 6 0 1 1 0 6X 6Y 1 1 1 0 0 7 1 1 1 0 7X 7Y 0 1 0 0 0 0 1 1 0 0 8 9 0 1 0 1 0 10 1 0 1 0 0 1 1 1 0 0 11 12 1 0 1 1 0 13 0 1 1 1 1 1 1 1 0 0 14 15 ABSOLUTE MAXIMUM RATING Symbol VDD * Vi II Ptot Top Tstg Parameter Supply Voltage: HCC Types HCF Types Input Voltage Value Unit -0.5 to +20 -0.5 to +18 V V -0.5 to VDD + 0.5 V ± 10 200 mA mW 100 -55 to +125 -40 to +85 mW o C o C DC Input Current (any one input) Total Power Dissipation (per package) Dissipation per Output Transistor for Top = Full Package Temperature Range Operating Temperature: HCC Types HCF Types Storage Temperature -65 to +150 o C Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress ratingonly and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. * All voltage values are referred to VSS pin voltage. RECOMMENDED OPERATING CONDITIONS Symbol VDD Parameter Supply Voltage: HCC Types HCF Types VI Input Voltage Top Operating Temperature: HCC Types HCF Types Value Unit 3 to 18 3 to 15 V V 0 to VDD -55 to +125 -40 to +85 V o o C C 5/16 HCC/HCF4067B HCC/HCF4097B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Symbol IL Parameter Quiescent Supply Current Test Conditios VEE VSS VDD VIS (V) (V) (V) (V) 5 10 15 20 5 10 15 HCC types HCF types SWITCH On RON Resistance ∆ON CI 18 0 0 0 0 100 ±0.1 100 1000 18 100 ±0.1 100 1000 0 15 300 ±0.1 300 1000 0 15 300 ±0.1 300 1000 -5 5 0 ≤ VI ≤ VDD 0 0 0 0 0 HCC types HCF types Input Capacitance THIGH * Min. Max. 150 300 600 3000 150 300 600 1050 400 240 1050 400 240 HCF types Input High Voltage Input Leackage Current 0 Value 25 oC Min. Typ. Max. 0.04 5 0.04 10 0.04 20 0.08 100 0.04 20 0.04 40 0.04 80 470 180 125 470 180 125 10 10 5 0 Any HCC Channel OFF types All Channel OFF HCC (common types OUT/IN) Any HCF Channel OFF types All Channel OFF HCF (common types OUT/IN) C Capacitance Input Output for 4067 Output for 4097 Feedthrough CONTROL Input Low V IL Voltage IIH IIL 800 310 200 850 330 210 0 ≤ VI ≤ VDD OFF (•) Channel Leakage Current VIH 5 10 15 5 10 15 5 10 15 HCC types Resistance ∆RON (Between any two channels) TLOW * Min. Max. 5 10 20 100 20 40 80 0 1300 580 320 1200 520 300 µA Ω Ω µA = VDD thru 1KΩ V EE=VSS RL =1KΩ to VSS IIS < 2µA (on all OFF channels) 5 10 15 5 10 15 5 55 35 0.2 1.5 3 4 3.5 7 11 pF 1.5 3 4 3.5 7 11 1.5 3 4 3.5 7 11 18 ±0.1 ±10-3 ±0.1 ±1 VI = 0/15V 15 ±0.3 ±10-3 ±0.3 ±1 5 7.5 Any Address or Inhibit Input V V VI = 0/18V • Determined by minimum feasible leakage measurement for automatic testing * TLOW = -55 oC for HCC device: -40 oC for HCF device. * THIGH = +125 oC for HCC device: +85 oC for HCF device. The Noise Margin for both ”1” and ”0” level is: 1V min. with VDD = 5 V, 2 V min. with VDD = 10 V, 2.5 V min. with VDD = 15 V 6/16 Unit µA pF HCC/HCF4067B HCC/HCF4097B DYNAMIC ELECTRICAL CHARACTERISTICS (Tamb = 25 o C, C L = 50 pF, RL = 200 KΩ, o typical temperature coefficent for all VDD values is 03 %/ C, all input rise and fall times= 20 ns) Symbol Parameter VC (V) SWITCH Propagation Delay tpd Time (Signal Input to Output) = VDD Frequency Response Channel ”ON” (Sine Wave Input) at VO 20 Log = − 3 dB VI = VDD Feedthrough (All Channels OFF) at VO 20 Log = − 40 dB VI Frequency Signal Crosstalk at VO(B) 20Log = −40dB VI(A) = VSS Sine Wave Distortion (fis = 1KHz sine wave) 5 10 15 CONTROL (address or Inhibit) Propagation Delay tPLH tPHL Time: Address or Inhibit to Signal OUT (Channel Turning ON) tPLH tPHL 200 0 1 5 (•) 1 5 (•) 0 0 1 10 10 10 1 5 (•) 1 1 1 2 (•) 3 (•) 5 (•) 0 Typ. Max. 10 10 10 V O at Common OUT/IN 4067B 4097B 30 15 11 14 20 60 30 20 V O at Any Channel 60 V O at Common OUT/IN 20 12 4067B 4097B 8 Between Any two (A and B) Channels Between Measured Sections on (A and B) common 4097B Measured only on Any Channel 1 10 MHz 18 0.3 0.2 0.12 0 0 0 5 10 15 325 135 95 650 270 190 5 10 15 220 90 65 440 180 130 10 0.3 Address or Inhibit to Signal Crosstalk 10* 0 ns MHz V O at Any Channel 5 10 15 0 0 0 Unit ns 0 0 0 Propagation Delay Time: Address or Inhibit to Signal OUT (Channel Turning OFF) (•) Peak to peak voltage symmetrical about Value 5 10 15 VC(A)=VDD VC(B)=VSS tW Test Conditions RL fi VI VSS VDD (KΩ) (KHz) (V) (V) (V) 75 % ns ns mV peak VDD − VSS 2 (*) Both ends of channel 7/16 HCC/HCF4067B HCC/HCF4097B Typical ON Resistance vs Input Signal Voltage (All Types) Typical ON Resistance vs Input Signal Voltage (All Types) Typical ON Resistance vs Input Signal Voltage (All Types) Typical ON Resistance vs Input Signal Voltage (All Types) TEST CIRCUITS OFF Channel Leakage Current Any Channel OFF For 4067B 8/16 For 4097B HCC/HCF4067B HCC/HCF4097B OFF Channel Leakage Current All Channels OFF For 4067B For 4097B Input Voltage Measure < 2 µA an All OFF Channels (e.g. Channel 12) For 4067B For 4097B Quiescent Device Current For 4067B For 4097B 9/16 HCC/HCF4067B HCC/HCF4097B Turn-on and Turn-off Propagation Delay Address Select Input to Signal Output (e. g. Channel 0) For 4067B For 4097B Turn-on and Turn-off Propagation Delay-Inhibit Input to Signal Output (e. g. Channel 1) For 4067B Channel ON Resistance Measurement Circuit 10/16 For 4097B HCC/HCF4067B HCC/HCF4097B Propagation Delay Waveform Channel Being Turned ON (RL = 10 KΩ, CL = 50 pF) Propagation Delay Waveform Channel Being Turned OFF (RL = 300 Ω, CL = 50 pF) APPLICATIONS INFORMATION In applications where separate power sources are used to drive VDD and the signal inputs, the VDD current capability should exceed VDD/RL (RL = effective external load). This provision avoids permanent current flow or clamp action on the VDD supply when power is applied or removed from the HCC/HCF4067B or HCC/HCF4097B. When switching from one address to another, some of the ON periods of the channels of the multiplexers will overlap momentarily, which may be objectionable in certain applications. Also when a channel is turned ON or OFF by an address input, there is a momentary conductive path from the channel to VSS, which will drump some charge from any capacitor connected to the input or output of the channel. The inhibit input turning on a channel will similarly drump some charge to VSS. The amount of charge dumped is mostly a function of the signal level above VSS. Typically, ay VDD - VSS = 10V, a 100 pF capacitor connected to the input or output of the channel will lose 3-4% of its voltage at the moment the channel turns ON or OFF. This loss of voltage is essentially independent of the address or inhibit signal trnasition time, if the transition time is less than 1- 2 µs. When the inhibit signal turns a channel off, there is no change dumping of VSS. Rather, there is a slight rise in the channel voltage level (65 mV typ.) due to the capacitance coupling from inhibit input to channel input or output. Address input also couple some voltage steps onto the channel signal levels. In certain applications, the external load-resistor current may include both VDD and signal line components. To avoid drawing VDD current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0.8 V (calculated from RON values shown in ELECTRICAL CHARACTERISTICS CHART). No VDD current will flow through RL if the switch current flows into terminal 1 on the HCC/HCF4067B, terminals 1 and 17 on the HCC/HCF4097B. 11/16 HCC/HCF4067B HCC/HCF4097B Plastic DIP24 (0.25) MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. a1 0.63 0.025 b 0.45 0.018 b1 0.23 b2 0.31 1.27 D E 0.009 0.012 0.050 32.2 15.2 16.68 1.268 0.598 0.657 e 2.54 0.100 e3 27.94 1.100 F MAX. 14.1 0.555 I 4.445 0.175 L 3.3 0.130 P043A 12/16 HCC/HCF4067B HCC/HCF4097B Ceramic DIP24 MECHANICAL DATA mm DIM. MIN. TYP. A inch MAX. MIN. TYP. 32.3 MAX. 1.272 B 13.05 13.36 0.514 0.526 C 3.9 5.08 0.154 0.200 D 3 E 0.5 e3 0.118 1.78 0.020 27.94 0.070 1.100 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 I 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 1.52 2.49 0.060 0.098 15.8 0.606 0.622 N1 P Q 4° (min.), 15° (max.) 15.4 5.71 0.225 P058C 13/16 HCC/HCF4067B HCC/HCF4097B SO24 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. A a1 MIN. TYP. MAX. 2.65 0.10 0.104 0.20 a2 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45° (typ.) D 15.20 15.60 0.598 0.614 E 10.00 10.65 0.393 0.420 e 1.27 0.05 e3 13.97 0.55 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 S 8° (max.) L s e3 E D 13 1 12 F 24 14/16 b1 e a1 b A a2 C c1 HCC/HCF4067B HCC/HCF4097B PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 15/16 HCC/HCF4067B HCC/HCF4097B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 16/16