HY51V(S)65163HG/HGL 4M x 16Bit EDO DRAM PRELIMINARY DESCRIPTION This familiy is a 64Mbit dynamic RAM organized 4,194,304 x 16bit configuration with Extended Data Out mode CMOS DRAMs. Extended data out mode is a kind of page mode which is useful for the read operation. The advanced circuit and process allow this device to achieve high performance and low power dissipation. Features are access time(45ns or 50ns) and refresh cycle(4K ref ) and power consumption (Normal or low power with self refresh). Advanced CMOS process as well as circuit techniques for wide operating margins allow this device to achieve high speed access and high reliability FEATURES • • • • • • • Extended data out operation Read-modify-write capability Multi-bit parallel test capability LVTTL(3.3V) compatible inputs and outputs /RAS only, CAS-before-/RAS, Hidden and self refresh(L-version) capability • JEDEC standard pinout 50pin plastic SOJ/TSOP-II(400mil) Single power supply of 3.3V +/- 10% Battery back up operation(L-version) • • Fast access time and cycle time Part No tRAC tAA tCAC tRC tHPC HY51V(S)65163HG/HGL-45 45ns 23ns 12ns 74ns 17ns HY51V(S)65163HG/HGL-5 50ns 25ns 13ns 84ns 20ns HY51V(S)65163HG/HGL-6 60ns 30ns 15ns 104ns 25ns Power dissipation Active Standby • 45ns 50ns 60ns 468mW 432mW 396mW 1.8mW(CMOS level Max) 0.72mW (L-version : Max) Refresh cycle Part No Ref Normal HY51V65163HG* 4K Ref 64ms HY51V65163HGL* 4K Ref L-part 128ms * : /RAS only, CBR and hidden refresh ODERING INFORMATION Part Number Access Time Package HY51V(S)65163HG/HG(L)J-45 HY51V(S)65163HG/HG(L)J-5 HY51V(S)65163HG/HG(L)J-6 45ns 50ns 60ns 400mil 50pin SOJ HY51V(S)65163HG/HG(L)T-45 HY51V(S)65163HG/HG(L)T-5 HY51V(S)65163HG/HG(L)T-6 45ns 50ns 60ns 400mil 50pin TSOP-II (S) : Self refresh, (L) : Low power This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev.0.1/Apr.01 HY51V(S)65163HG/HGL PIN CONFIGURATION VCC 1 50 VSS IO0 2 49 IO1 3 48 IO14 IO2 4 47 IO13 IO12 IO15 IO3 5 46 VCC 6 45 VSS IO4 7 44 IO11 IO5 8 43 IO10 IO6 9 42 IO9 IO7 10 41 IO8 NC 11 40 NC VCC 12 39 VSS /WE 13 38 /LCAS /RAS 14 37 /UCAS NC 15 36 /OE NC 16 35 NC NC 17 34 NC NC 18 33 NC A0 19 32 A11 A1 20 31 A10 A2 21 30 A9 A3 22 29 A8 A4 23 28 A7 A5 24 27 A6 VCC 25 26 VSS 50 Pin Plastic SOJ / TSOP-II PIN DESCRIPTION Pin Function /RAS Row Address Strobe /UCAS, /LCAS Column Address Strobe /WE Write Enable /OE Output Enable A0-A11 Address Inputs A0-A11 Refresh Address Inputs I/O 0- I/O15 Data Input / Output Vcc Power (3.3V) Vss Ground NC No connection Rev.0.1/Apr.01 2 HY51V(S)65163HG/HGL ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Ambient Temperature TA 0 ~ 70 o C Storage Temperature TSTG -55 ~ 125 o C Voltage on Any Pin relative to Vss VT -0.5 ~ Vcc + 0.5 (Max 4.6V) V Voltage on Vcc relative to Vss Vcc -0.5 ~ 4.6 V Short Circuit Output Current IOUT 50 mA Power Dissipation PT 1 W Note : Operation at above absolute maximum rating can adversely affect device reliability. Recommended DC OPERATING CONDITIONS (TA=0 to 70 oC) Parameter Symbol Min Typ. Max Unit Note Power Supply Voltage Vcc 3.0 3.3 3.6 V 1,2 Power Supply Voltage Vss 0 0 0 V 2 Input High Voltage VIH 2.0 - Vcc + 0.3 V 1 Input Low Voltage VIL -0.3 - 0.8 V 1 Note : All voltages are referenced to Vss 1. 6.0V at pulse width 10ns which is measured at Vcc 2. -0.1V at pulse width 10ns which is measured at Vss Rev.0.1/Apr.01 3 HY51V(S)65163HG/HGL DC CHARACTERISTICS (Vcc = 3.3V +/- 10%, TA=0 to 70°C) Symbol Parameter Min Max Unit 2.4 Vcc V 0 0.4 V 45ns - 130 50ns - 120 60ns - 110 - 1 45ns - 130 50ns - 120 60ns - 110 45ns - 100 50ns - 90 60ns - 80 CMOS interface ( /RAS, /UCAS, /LCAS >= Vcc-0.2V, Dout = High-Z) - 0.5 mA Standby current ( L-version) - 200 uA 45ns - 130 50ns - 120 60ns - 110 VOH Output Level Output Level voltage(Iout= -2mA) VOL Output Level Output Level voltage(Iout=2mA) ICC1 ICC2 ICC3 ICC4 Operating current ( tRC = tRC min) Standby current (TTL interface) Power supply standby current (/RAS, /UCAS,/LCAS=VIH, Dout = High-Z) /RAS only refresh current (tRC= tRC min) Extended data out page mode current (/RAS=VIL, /CAS, Address cycling : tHPC=tHPC min) mA Note 1, 2 mA mA 2 mA 1, 3 ICC5 ICC6 /CAS-before-/RAS refresh current (tRC=tRC min) 4 mA ICC7 Battery back up operating current (standby with CBR) (tRC=31.25us, tRAS=300ns, Dout=High-Z) - 350 uA 4, 5 ICC8 Standby current (CMOS) Power supply standby current /RAS=VIH, /UCAS./LCAS=VIL, Dout=Enable) - 5 mA 1 ICC9 Self refresh current (/RAS, /UCAS, /LCAS <=0.2V, Dout=High-Z) - 350 uA 5 II(L) Input leakage current, Any input (0V<= Vin<=Vcc) -5 5 uA IO(L) Output leakage current, (Dout is disabled, 0V<= Vout<=Vcc) -5 5 uA Note : 1. Icc depends on output load condition when the device is selected, Icc(max) is specified at the output open condition 2. Address can be changed once or less while RAS=VIL 3. Measured with one sequential address change per EDO cycle, tHPC 4. VIH>=Vcc-0.2V, 0V<=VIL<=0.2V 5. L-Version Rev.0.1/Apr.01 4 HY51V(S)65163HG/HGL CAPACITANCE (Vcc=3.3V +/-10%, TA=25°C) Parameter Symbol Min. Max Unit Note Input capacitance (Address) CI1 - 5 pF 1 Input capacitance (Clocks) CI2 - 5 pF 1 Output capacitance (Data-in, Data-out) CI/O - 7 pF 1, 2 Note : 1. Capacitance measured with Boonton Meter or effective capacitance measuring method. 2. /RAS, /UCAS and /LCAS = VIH to disable Dout AC CHARACTERISTICS (Vcc=3.3V +/-10%, TA=0~70C, Note 1, 2, 19,20) Test Condition • • • Input rise and fall times = 2ns Input level : VIL/VIH = 0.0 / 0.3V Input timing reference level : VIL/VIH = 0.8/2.0V • Output timing reference level : VOL/VOH=0.8/0.2V Output load : 1 TTL gate + CL (100pF) including scope and jig • Read, Write, Read-modify-Write and Refresh Cycles -45 Parameter -50 -60 Symbol Unit Min Max Min Max Min Max Note Random read or write cycle time tRC 74 - 84 - 104 - ns /RAS precharge time tRP 25 - 30 - 40 - ns /CAS precharge time tCP 7 - 8 - 10 - ns /RAS pulse width tRAS 45 10,000 50 10,000 60 10,000 ns /CAS pulse width tCAS 7 10,000 8 10,000 10 10,000 ns Row address set-up time tASR 0 - 0 - 0 - ns Row address hold time tRAH 7 - 8 - 10 - ns Column address set-up time tASC 0 - 0 - 0 - ns 21 Column address hold time tCAH 7 - 8 - 10 - ns 21 /RAS to /CAS delay time tRCD 11 33 12 37 14 45 ns 3 /RAS to Column address delay time tRAD 9 22 10 25 12 30 ns 4 /RAS hold time tRSH 12 - 13 - 15 - ns /CAS hold time tCSH 38 - 40 - 42 - ns /CAS to /RAS precharge time tCRP 5 - 5 - 5 - ns Rev.0.1/Apr.01 24 22 5 HY51V(S)65163HG/HGL - continued -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Unit Note /OE to Din delay time tODD 12 - 13 - 15 - ns 5 /OE delay time from Din tDZO 0 - 0 - 0 - ns 6 /CAS delay time from Din tDZC 0 - 0 - 0 - ns 6 Transition time ( Rise and Fall) tT 2 50 2 50 2 50 ns 7 - 64 - 64 - 64 ms 4K Ref. - 128 - 128 - 128 ms 4K Ref. Unit Note Refresh period tREF Refresh period (L-version) Read Cycles -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Access time from /RAS tRAC - 45 - 50 - 60 ns 8, 9 Access time from /CAS tCAC - 12 - 13 - 15 ns 9,10,17 Access time from column address tAA - 23 - 25 - 30 ns 9,11,17 Access time from /OE tOAC - 12 - 13 - 15 ns 9 Read command set-up time tRCS 0 - 0 - 0 - ns 21 Read command hold time to /CAS tRCH 0 - 0 - 0 - ns 12,22 Read command hold time to /RAS tRRH 0 - 0 - 0 - ns 12 Column address to /RAS lead time tRAL 23 - 25 - 30 - ns Column address to /CAS lead time tCAL 15 - 15 - 18 - ns Output buffer turn off delay time from /CAS tOFF - 12 - 13 - 15 ns 13,26 Output buffer turn off delay time from /OE tOEZ - 12 - 13 - 15 ns 13 /CAS to Din delay time tCDD 12 - 13 - 15 - ns 5 /RAS to Din delay time tRDD 12 - 13 - 15 - ns /WE to Din delay time tWDD 12 - 13 - 15 - ns Output buffer turn off delay time from /RAS tOFR - 12 - 13 - 15 ns 13,26 Output buffer turn off delay time from /WE tWEZ - 12 - 13 - 15 ns 13 Output data hold time tOH 3 - 3 - 3 - ns 26 Output data hold time from /RAS tOHR 3 - 3 - 3 - ns 26 Read command hold time from /RAS tRCHR 45 - 50 - 60 - ns Output data hold time from /OE tOHO 3 - 3 - 3 - ns /CAS to output in low-Z tCLZ 0 - 0 - 0 - ns Rev.0.1/Apr.01 6 HY51V(S)65163HG/HGL Write Cycles -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Unit Note Write command set-up time tWCS 0 - 0 - 0 - ns 14,21 Write command hold time tWCH 7 - 8 - 10 - ns 21 Write command pulse width tWP 7 - 8 - 10 - ns Write command to /RAS lead time tRWL 12 - 13 - 15 - ns Write command to /CAS lead time tCWL 7 - 8 - 10 - ns 23 Data-in set-up time tDS 0 - 0 - 0 - ns 15, 23 Data-in hold time tDH 7 - 8 - 10 - ns 15, 23 Unit Note Read-Modify-Write Cycles -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Read-modify-write cycle time tRWC 101 - 116 - 140 - ns /RAS to /WE delay time tRWD 63 - 67 - 79 - ns 14 /CAS to /WE delay time tCWD 30 - 30 - 34 - ns 14 Column address to /WE delay time tAWD 40 - 42 - 49 - ns 14 /OE hold time from /WE tOEH 12 - 13 - 15 - ns Refresh cycles -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Unit Note /CAS set-up time ( /CAS-before-/RAS Refresh Cycle) tCSR 5 - 5 - 5 - ns 21 /CAS hold time ( /CAS-before-/RAS Refresh Cycle) tCHR 7 - 8 - 10 - ns 22 /WE set-up time ( /CAS-before-/RAS Refresh Cycle) tWRP 0 - 0 - 0 - ns /WE hold time ( /CAS-before-/RAS Refresh Cycle) tWRH 7 - 8 - 10 - ns /RAS precharge to /CAS hold time ( /CAS-before-/RAS Refresh Cycle) tRPC 5 - 5 - 5 - ns Rev.0.1/Apr.01 21 7 HY51V(S)65163HG/HGL Extended Data Out Mode Cycles -45 Parameter -50 -60 Symbol Min Max Min Max Min Max Unit Note 25 EDO page mode cyle time tHPC 17 - 20 - 25 - ns Write pulse width during /CAS precharge tWPE 7 - 8 - 10 - ns EDO mode /RAS pulse width tRASP - 100K - 100K - 100K ns 16 Access time from /CAS precharge tACP - 28 - 28 - 35 ns 9,17,22 /RAS hold time from /CAS precharge tRHCP 26 - 28 - 35 - ns /CAS hold time referred /OE tCOL 7 - 8 - 10 - ns /CAS to /OE set-up time tCOP 5 - 5 - 5 - ns Read command hold time from /CAS precharge tRCHP 26 - 28 - 35 - ns Output data hold time from /CAS low tDOH 3 - 3 - 3 - ns /OE precharge time tOEP 7 - 8 - 10 - ns 9,27 EDO Page Mode Read-Modify-Write Cycle -45 Parameter -50 -60 Symbol Unit Min Max Min Max Min Max Note EDO read-modify-write cycle time tHPRWC 57 - 57 - 68 - ns EDO page mode read-modify-write cycle /CAS precharge to /WE delay time tCPW 45 - 45 - 54 - ns 14,22 Unit Note Self Refresh Cycle (L-Version) -45 Parameter -50 -60 Symbol Min Max Min Max Min Max /RAS pulse width ( self refresh) tRASS 100 - 100 - 100 - us 31 /RAS precharge time ( self refresh) tRPS 90 - 90 - 110 - ns 31 /CAS hold time ( self refresh) tCHS -50 - -50 - -50 - ns 23 Rev 0.1 / Apr. 01 HY51V(S)65163HG/HGL Notes : 1. AC measurements assume t T = 2ns 2. AC initial pause of 200us is required after power up followed by a minimum of eight initialization cycles ( any combination of cycles containing /RAS-only refresh or /CAS-before-/RAS refresh) 3. Operation with the tRCD(max) limit insures that tRAC(max) can be met, t RCD(max) is specified as a reference point only : if tRCD is greater than the specified tRCD(max) limit, then access time is controlled exclusively by tCAC. 4. Operation with the tRAD(max) limit insures that tRAC(max) can be met, tRAD(max) is specified as a reference point only : if tRAD is greater than the specified tRAD(max) limit, then access time is controlled exclusively by tAA. 5. Either tODD or tCDD must be satisfied. 6. Either tDZO or tDZC must be satisfied. 7. VIH(min) and VIL(max) are reference levels for measuring timing of input signals, also transition times are measured between V IH(min) and VIL(max) 8. Assumes that tRCD<=tRCD(max) and tRAD<=tRAD(max). If tRCD or tRAD is greater than the maximum recommended value shown in this table, tRAC exceeds the value shown 9. Measured with a load circuit equivalent to 1 TTL loads and 100pF. 10. Assumes that tRCD>=tRCD(max) and tRCD + tCAC(max) >= tRAD + tAA(max) 11. Assumes that tRAD>=tRAD(max) and tRCD + tCAC(max) <= tRAD + tAA(max) 12. Either tRCH of tRRH must be satified for a read cycles 13. tOFF(max), tOEZ(max), tOFR(max) and tWEZ(max) define the time at which the outputs achieve the open circuit condition and is not referenced to output voltage levels 14 tWCS, tRWD, tCWD, tAWD and tCPW are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only : If tWCS >=tWCS(min), the cycle is an early write cycle and the data out pin will remain open circuit(high impedance) throughout the entire cycle : If tRWD>=tRWD(min), tCWD>=tCWD(min), tAWD>=tAWD(min), the cycle is a read-modify-write and the data output will contain data read from the selected cell : if neither of the above sets of conditions is satified, the condition of the data out (at access time) is indeterminate. 15. tDS and tDH are refered to /UCAS and /LCAS leading edge in early write cycles and to /WE leading edge in delayed write or read-modify-write cycles 16. tRASP defineds /RAS pulse width in extended data out mode cycles 17. Access time is determined by the longest among tAA, tCAC and tACP 18 In delaying write or read-modify-write cycles, /OE must disable output buffer prior to applying data to the device. Rev 0.1 / Apr. 01 HY51V(S)65163HG/HGL 19. When output buffers are enabled once, sustain the low impedence state until valid data is obtained. when output buffer is turned on and off within a very short time, generally it causes large Vcc/Vss line noise, which causes to degrade V IH min / VIL max level 20. When both /UCAS and /LCAS go low at the same time, all 16 bit data are written into the device. /UCAS and /LCAS cannot be staggered within the same write / read cycles 21. tASC, tCAH, tRCS, tWCS, tWCH, tCSR and tRPC are determined by the earlier falling edge of /UCAS or /LCAS 22. tCRP, tCHR, tRCH,tACP and tCPW are determined by the later rising edge of /UCAS or /LCAS 23. tCWL, tDH, tDS and tCHS should be satified by the both /UCAS and /LCAS 24. tCP is determined by the time that both /UCAS and /LCAS are high 25. tHPC(min) can be achieved during a series of EDO mode early write cycles or EDO mode read cycels If both write and read operation are mixed in a EDO mode, /RAS cycle[EDO mode mix cycle (1)(2)] minimum value of /CAS cycle t HPC[tCAS + tCP + 2tT] become greater than the specified tHPC(min) value. The value of CAS cycle time of mixed EDO page mode is shown in EDO page mode mix cycle (1) and (2) 26. Data output turns off and becomes high impedance from later rising edge of /RAS and /CAS. Hold time and turn off time are specified by the timing specifications of later rising edge of /RAS and /CAS between tOHR and tOH and between tOFR and tOFF 27. tDOH defines the time at which the output level go cross, VOL=0.8V, VOH=2.0V of output timing reference level. 28. Before and after self refresh mode, execute CBR refresh to all refresh addresses in or within 64ms period on the condition a) and b) below a) Enter self refresh mode within 15.6us after either burst refresh or distributed refresh at equal interval to all refresh addresses are completed. b) Start burst refresh or distributed refresh at equal interval to all refresh addresses within 15.6us after exiting from self refresh mode 29. In case of entering from /RAS-only-refresh, It is necessary to execute CBR refresh before and after self refresh mode according as note 28 30. For L-version, It is available to apply each 128ms and 31.2us instead of 64ms and 15.6us at note 28 31. At tRASS > 100us, self refresh mode is activated, and not active at tRASS < 10us, It is undefined within the range of 10us < tRASS < 100us. For tRASS > 10us, It is necessary to satify tRPS 32. XXX : H or L [ H : VIH(min) <= VIN <=VIH(max), L : VIH(min) <=VIN <=VIH(max)] ///// : Invalid Dout When the address, clock and input pins are not described on timing waveforms, their pins must be applied VIH or VIL Rev 0.1 / Apr. 01 HY51V(S)65163HG/HGL PACKAGE INFORMATION 400mil 50pin TSOP- II Dimension Unit: mm 10.16 1.20 MAX 1.15 MAX 0.30 0.10 0.28 0.08 0.80 0.80 11.96 MAX 0.40 MIN 0.60 MAX 11.56 MIN 0 ~ 5 deg. 0.145 0.05 0.125 0.04 0.68 20.95 MIN 21.35 MAX 0.08 MIN 0.18 MAX 0.10 Dimension including the plating thickness Base material dimension Rev.0.1/Apr.01 11