IK Semicon IK62783N 8ch darlington source driver Datasheet

TECHNICAL DATA
8CH DARLINGTON SOURCE DRIVER
IK62783/4
IK62783N
IK62784N
The IK62783, IK62784 are eight current drivers with
common power supply and ground.
The IK62783, IK62784 are purposed to use different
devices: relays, lamps, displays (LED & gas discharge
cells), in fluorescent indicators, telecommunication lines
and logic devices.
18
DIP-18
IK62783D
IK62784D
SOP-18
FEATURES
IK62783DH
IK62784DH
• High output voltage up to 50V
• One channel output current up to minus 500 mA
• Output clamp diodes
SOP-20
• Single supply voltage 50V
Ta=-40 ~ 85°C For all package
Permissible value of electrostatic potential 2000V
Table 1 – ELECTRIC CIRCUITRY DIFFERENCE OF ICS
IC Marking
Quantity of Serially
Connected Diodes
Applicable with ICs
IK62783N/D/DH
3
TTL, 5 V CMOS
IK62784N/D/DH
6
6 ~ 15 V P-MOS, CMOS
Mart, 2013, ver. 06
IK62783/4
Table 2 – PIN DESCRIPTION (DIP-18, SOP-18)
Pin Number
Symbol
Description
01
02
03
04
05
06
07
08
09
10
11
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
Vcc
GND
OUT 8
Input
Input
Input
Input
Input
Input
Input
Input
Supply voltage pin
Common pin (ground)
Output
12
OUT 7
Output
13
OUT 6
Output
14
OUT 5
Output
15
OUT 4
Output
16
OUT 3
Output
17
OUT 2
Output
18
OUT 1
Output
Table 3 – PIN DESCRIPTION (SOP-20)
Pin Number
01
02
03
04
05
06
07
08
09
10
11
12
13
Symbol
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
Vcc
NC
NC
GND
OUT 8
Description
Input
Input
Input
Input
Input
Input
Input
Input
Supply voltage pin
NC
NC
Common pin (ground)
Output
14
OUT 7
Output
15
OUT 6
Output
16
OUT 5
Output
17
OUT 4
Output
18
OUT 3
Output
19
OUT 2
Output
20
OUT 1
Output
March, 2013, ver. 06
IK62783/4
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Norm
Unit
Min
Max
VCC
Supply voltage
-
50
V
IOUT
Output current (one channel)
-
-500
mA
Input voltage for IK62783
for IK62784
Clamp diode reverse voltage
-0.5
-0.5
-
15
30
50
V
Clamp diode forward current
Storage temperature
IK62783/4N
Power Dissipation
IK62783/4DW/DH
-60
500
150
mA
o
C
W
W
VIN
VR
IF
Tstg
PD
1.47
0.96
V
* Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at these or any other conditions beyond those
indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATION MODES
Symbol
Parameter
Norm
Unit
Min
-
Max
50
-350
V
mA
VCC
IOUT
Supply voltage
Output current (one channel)
VR
Control pin diode reverse voltage
-
50
V
IF
Control pin diode forward current
-
400
mA
PD
Power Dissipation
IK62783/4N
-
0.52
IK62783/4DW/DH
0.4
W
March, 2013, ver. 06
IK62783/4
ELECTRICAL CHARACTERISTICS
Symbol
Parameter
Measurement mode
VIN(ON)
Input voltage at open (ON)
state of output
IOUT = -350 mA
VCE = 2 V
VIN(OFF)
Icc(ON)
VCE(sat)
Input voltage at close
(OFF) state of output,
Consumption current
Collector-emitter
saturation voltage
ICEX
Output leakage current at
close (OFF) state of output
VF
Forward DC voltage of
clamp diode
IOUT = -500 A
P/N
IK62783
-
IK62784
-
IK62783
IK62784
VIN = 2 V
VCC = 50 V
VIN = 4.5 V
VCC = 50 V
IOUT = -100 mA
VIN = 2 V
IOUT = -225 mA
VIN = 2 V
IOUT = -350 mA
VIN = 2 V
IOUT = -100 mA
VIN = 4.5 V
IOUT = -225 mA
VIN = 4.5 V
IOUT = -350 mA
VIN = 4.5 V
Norm
Min
0.8
0.64
2.0
1.6
IK62783
IK62784
IK62783
-
IK62784
-
Input current
Reverse current of clamp
diode
1.8
2.16
1.9
2.28
2.0
2.4
1.8
2.16
1.9
2.28
2.0
2.4
-
2.0
2.4
-
VIN = 5 V
IK62784
IR
2.5
3.0
IF = 350 mA
VIN = 3.85 V
VIN = 12 V
-
VR = 50 V
-
V
V
100
-
Unit
-
-
IK62783
Ta
(C)
-
VCC = 50 V
VIN = 0.4 V
VIN = 2.4 V
IIN(ON)
Max
2.0
2.4
4.5
5.4
0.052
0.062
0.26
0.31
0.13
0.156
1.13
1.356
50
60
mA
25±10
-40 to 85
V
25±10
A
V
25±10
-40 to 85
mA
A
March, 2013, ver. 06
IK62783/4
TYPICAL ELECTRIC PARAMETERS at Ta = 25 oC
Symbol
Parameter
Measurement
mode
Typical value
Unit
tON
Switch -ON delay
RL = 125 ,
VCC = 50 V
0.15
s
tOFF
Switch-OFF delay
CL = 15 pF
3.0
s
for 18pins
for 20pins
Fig 1 – Electric block diagram
March, 2013, ver. 06
IK62783/4
VCC
R3
20к
VD1
R1
10k
VT2
IN
VT1
VT3
R2
2,6k
VD4
VD2
VD7
VT4
VD3
R4
10k
R5
5k
OUT
VD5
VD6
GND
Fig. 2 – Electrical scheme of one channel of ICs IK62783
VCC
R3
20k
VD1
R1
10k
VT2
IN
VT1
VT3
VT4
VD3
VD2
VD4
R2
2,6k
R4
10k
VD10
R5
5k
OUT
VD5
VD6
VD9
VD7
VD8
GND
Fig. 3 – Electrical scheme of one channel of ICs IK62784
March, 2013, ver. 06
IK62783/4
V
V
10ns
5ns
90%
Input
50%
10%
VIH
90%
50%
50 мкс
tON
10%
0V
tOFF
VOH
Output
50%
50%
VOL
0
t
ns
Pulse width 50 s, ratio (duty cycle) 100%  tW / T = 10% ( tW – pulse width, s; T – period , s)
Fig. 4 – Time diagram of IK62783, IK62784 at measurement of signal delay at
switching -ON tON and switching -OFF tOFF
March, 2013, ver. 06
IK62783/4
PACKAGE DIMENSIONS
DIP-18
Unit: mm
March, 2013, ver. 06
IK62783/4
SOP-18
March, 2013, ver. 06
IK62783/4
SOP-20
March, 2013, ver. 06
Similar pages