NSC LM2419T Triple 65 mhz crt driver Datasheet

LM2419
Triple 65 MHz CRT Driver
General Description
Features
The LM2419 contains three wide bandwidth, large signal
amplifiers designed for large voltage swings. The amplifiers
have a gain of b15. The device is intended for use in color
CRT monitors and is a low cost solution to designs conforming to 1024 x 768 display resolution.
The device is mounted in the industry standard 11-lead
TO-220 molded power package. The heat sink is electrically
isolated and may be grounded for ease of manufacturing
and EMI/RFI shielding.
Y
Y
Y
Y
Y
50 VPP output swing at 65 MHz
Rise/Fall time 5 ns with 12 pF load
60 VPP output swing capability
Pin and function compatible with LM2416
No low frequency tilt compensation required
Applications
Y
CRT driver for SVGA, IBM 8514 and 1024 x 768
display resolution RGB monitors
Schematic and Connection Diagrams
One Channel
TL/H/11442 – 1
TL/H/11442 – 2
Order Number LM2419T
See NS Package Number TA11B
C1995 National Semiconductor Corporation
TL/H/11442
RRD-B30M115/Printed in U. S. A.
LM2419 Triple 65 MHz CRT Driver
December 1994
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
a 85V
Supply Voltage (V a )
b 25§ C to a 100§ C
Storage Temperature (TSTG)
b 20§ C to a 90§ C
Operating Case Temperature, TCase
Lead Temperature (soldering k10 sec.)
300§ C
ESD Tolerance
2 kV
Electrical Characteristics
Unless otherwise specified, the following specifications apply for V a e 80V, DC input bias, VIN DC e 3.9V; 50 VPP output
swing; frequency e 1 MHz; VBias e 12V; CL e 12 pF; TA e 25§ C; see test circuit, Figure 1 .
Symbol
Min
(Note 3)
Typ
(Note 2)
Max
(Note 3)
Units
(Limit)
27
40
mA
Parameter
Conditions
ICC
Supply Current (per Amplifier)
Input/Output Open Circuit
IB
Bias Current (Pins 2 or 7 or 9)
VOUT
Output Offset Voltage
tr
Rise Time
10% to 90%
5
tf
Fall Time
90% to 10%
5
AV
Voltage Gain
OS
Overshoot
VIN: tr, tf k 2 ns
LE
Linearlty Error
VOUT e 25V to 75V
DAV match
Gain Matching
11
40
b 13
50
b 15
8
mA
60
V
ns
ns
b 18
V/V
%
8
%
0.3
dB
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. The guaranteed specifications apply only for the test conditions
listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
Note 2: Typical specifications are at 25§ C and represent the most likely parametric norm.
Note 3: Min/Max limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Typical Performance
Characteristics
TA e 25§ C, Test CircuitÐFigure 1
Frequency Response
TL/H/11442–3
*12 pF is the total load capacitance and includes the test fixture capacitance.
FIGURE 1. Test Circuit (One Section)
TL/H/11442 – 4
2
small signal cross over distortion. Resistor R3 is used to
prevent Q2 from oscillating at high frequencies.
Typical Performance
Characteristics (Continued)
TA e 25§ C, Test CircuitÐFigure 1
Pulse Response
TL/H/11442 – 5
TL/H/11442 – 7
FIGURE 2. Schematic Diagram of
One Section of LM2419
Test Circuit
Figure 1 shows a typical test circuit for evaluation of the
LM2419. The input signal is AC coupled into the input of
LM2419 and is referenced to 3.9V DC using an external
3.9V DC bias through a 390X resistor. The test circuit is
designed to allow testing of the LM2419 in a 50X environment such as a 50X oscilloscope or network analyzer. The
4950X resistor in series with the output of the LM2419
forms a 100:1 voltage divider when connected to a 50X
oscilloscope or network analyzer.
Application Hints
POWER SUPPLY BYPASS
Since the LM2419 is a wide-bandwidth amplifier with greater
than 10,000 V/ms slew rate, proper power supply bypassing
is critical for optimum performance. Improper power supply
bypassing can result in large overshoot, ringing and oscillation. A 0.01 mF ceramic capacitor should be connected as
close to the supply pin as is practical (preferably less than
(/4× from the supply pin). The lead length of the 0.01 mF
ceramic capacitor should be as small as is practical. In addition, 10 mF – 100 mF electrolytic capacitor should be connected from the supply pin to ground. The electrolytic capacitor should be placed reasonably close to the LM2419’s
supply pin.
Theory of Operation
The LM2419 is a high voltage triple CRT driver suitable for
SVGA, IBM 8514 and 1024 x 768 display resolution monitors. The device is packaged in the industry standard
11 lead TO-220 molded power package. The heat sink is
electrically isolated and may be grounded for ease of manufacturing and RFl/EMl shielding.
The schematic diagram of LM2419 is shown in Figure 2 . Q1
and R2 provide a conversion of the input voltage to current
while Q2 acts as a common base amplifier to drive the load
resistor, R1. Resistor R4 along with R2 sets up the DC bias
at the base of Q1. Emitter followers Q3 and Q4 isolate R1
from the capacitive load at the output, thus making the rise
and fall times relatively insensitive to the load capacitance.
The gain of the amplifier is bR1/(R2 ll R4) and is fixed at
approximately b15. The bandwidth of LM2419 is primarily
limited by the time constant due to R1 and the capacitances
associated with D1, Q2, Q3 and Q4. Diode D1 is used to
provide some bias voltage for Q3 and Q4 so as to reduce
ARC PROTECTION
The LM2419 must be protected from arcing within the CRT.
To limit the arcover voltage, a 200V spark gap is recommended at the cathode. Clamp diodes D1 and D2 (as
shown in Figure 3 ) are used to clamp the voltage at the
output of LM2419 to a safe level. The clamp diodes used
should have high current rating, low series impedance and
low shunt capacitance. Resistor R2 in Figure 3 limits the
arcover current while R1 limits the current into LM2419 and
reduces the power dissipation of the output transistors
when the output is stressed beyond the supply voltage.
Having large value resistors for R1 and R2 would be desirable but this has the effect of reducing rise and fall times.
3
Application Hints (Continued)
TL/H/11442 – 8
FIGURE 3. Typical Application Circuit (One Channel)
Table I. LM2419 Output Overshoot
vs Capacitive Loading for a Typical Device
IMPROVING RISE AND FALL TIMES
Because of an emitter follower output stage, the rise and fall
times of the LM2419 are relatively unaffected by capacitive
loading. However, the series resistors R1 and R2 (see Figure 3 ) will reduce the rise and fall times when driving the
CRT’s cathode which appears as a capacitive load. The capacitance at the cathode typically ranges from 8 pF to
12 pF.
To improve the rise and fall times at the cathode, a small
inductor is often used in series with the output of the amplifier. The inductor L1 in Figure 3 peaks the amplifier’s frequency response at the cathode, thus improving rise and fall
times. The inductor value is empirically determined and is
dependent on the load. An inductor value of 0.1 mH is a
good starting value. Note that peaking the amplifier’s frequency response will increase the overshoot.
Input Signal
tr/tf
CL
5 pF
8 pF
11 pF
1.2 ns
4%
6%
7%
8%
7 ns
4%
5%
6%
7%
15 pF
GAIN VS OUTPUT DC LEVEL
Figure 4 shows LM2419’s gain versus output DC level. A
100 mVPP AC signal is applied at the LM2419’s input and
the input signal’s DC level is swept. As can be seen from
Figure 4 , the amplifier’s gain is constant at approximately
15.4 (VOUT e 1.54 VPP) for output DC level between 35V
and 65V. Thus the amplifier’s output response is linear for
output voltage between 35V and 65V. If the output voltage
is less than 35V or more than 70V, the amplifier’s output
response becomes non-linear (note the change in gain, Figure 4 ). For optimum performance, it is recommended that
LM2419’s output low voltage be at 25V or above. For a
50 VPP swing, the output high voltage is 75V. With an output
signal swing from 25V to 75V, LM2419’s linearity error is
measured at 8%.
REDUCING OVERSHOOT
LM2419’s overshoot is a function of both the input signal
rise and fall times and the capacitive loading. The overshoot
is increased by either more capacitive loading or faster rise
and fall times of the input signal.
Table I shows the overshoot for a typical device with different capacitive loads and different input signal rise and fall
times. As can be observed from Table I, overshoot is large
for large capacitive loads and faster input signal rise and fall
times. In an actual application, the LM2419 is driven from a
preamplifier with rise and fall times of 3 ns to 7 ns. When
driven from LM1203 preamplifier (see application circuit,
Figure 6 ) the overshoot is 10% with 12 pF capacitive load.
The overshoot can be reduced by including a resistor in
series with LM2419’s output as in Figure 3 . Larger value
resistors for R1 and R2 would reduce overshoot but this
also increases the rise and fall times at the output. Frequency peaking using an inductor in series with the output may
restore the bandwidth.
TL/H/11442 – 9
FIGURE 4. Gain vs VOUT (DC), VIN e 100 mVPP
4
Application Hints (Continued)
The LM2419 requires that the package be properly heat
sunk under all operating conditions. Maximum ratings require that the device case temperature be limited to 90§ C
maximum. Thus for 50§ C maximum ambient temperature
and 13W maximum power dissipation, the thermal resistance of the heat sink should be:
isa s (90 – 50)§ C/13W e 3§ C/W
THERMAL CONSIDERATIONS
LM2419’s transfer characteristic and power dissipation versus DC input voltage is shown in Figure 5 . Power supply
current increases as the input voltage increases, consequently power dissipation increases. For the LM2419, the
worst case power dissipation occurs when a white screen is
displayed on the CRT. Considering a 20% black retrace
time in a 1024 x 768 display resolution application, the average power dissipation for continuous white screen is less
than 4W per channel with 50 VPP output signal (black level
at 75V and white level at 25V). Although the total power
dissipation is less than 12W for a continuous white screen,
the heat sink should be selected for 13W power dissipation
because of the variation in power dissipation from part to
part.
For thermal and gain linearity considerations, the output low
voltage (white level) should be maintained above 20V. If the
device is operated at an output low voltage below 20V, the
power dissipation might exceed 4.7W per channel (i.e., 14W
power dissipation for the device). Note that the device can
be operated at lower power by reducing the peak to peak
video output voltage to less than 50V and clamping the video black level close to the supply voltage.
SHORT CIRCUIT PROTECTION
The output of LM2419 is not short circuit protected. Shorting the output to either ground or to V a will destroy the
device. The minimum DC load resistance the LM2419 can
drive without damage is 1.6 kX to ground or V a . However,
driving a 1.6 kX load for an extended period of time is not
recommended because of power dissipation considerations. If the LM2419 is used to drive a resistive load then the
load should be 10 kX or greater.
RGB Video Application
A complete video section for an RGB CRT monitor is shown
in Figure 6 . The LM1203 video preamplifier and the LM2419
include almost all the circuitry required between the video
input connection and the CRT’s cathodes. However, an externally generated back porch clamp signal is required to
accomplish DC restoration of the video signal.
Figure 6 ’s circuit is excellent choice for a non-interlaced
1024 x 768 display resolution application. With 50 VPP output swing and 12 pF load, the rise/fall time for Figure 6 ’s
circuit was measured at 7.5 ns. In this application, feedback
is local to the LM1203. For detailed information on the
LM1203, please refer to the LM1203 data sheet.
PC BOARD LAYOUT CONSIDERATIONS
For optimum performance, adequate ground plane, isolation
between channels, good supply bypassing and minimizing
unwanted feedback are necessary. Moreover, the length of
the signal trace from the preamplifier to the LM2419 and
from the LM2419 to the cathode should be as short as is
practical. The following book is highly recommended:
Ott, Henry W, Noise Reduction Techniques in Electronic
Systems , John Wiley & Sons, New York, 1976.
TL/H/11442 – 10
FIGURE 5. VOUT and Power Dissipation vs VIN
5
Application Hints (Continued)
TL/H/11442 – 11
FIGURE 6. Typical VGA/SVGA Application
6
7
Unmarked capacitors 0.1 mF
Diodes FDH400
FIGURE 7. Typical SVGA/XGA Application
TL/H/11442 – 12
Application Hints (Continued)
LM2419 Triple 65 MHz CRT Driver
Physical Dimensions inches (millimeters)
Lit. Ý 107763
Order Number LM2419T
NS Package Number TA11B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages