ILPA25JUD SERIES 25W Dimmable Water-Proof Constant Current LED Driver – – – – – – – 2 Year Warranty Wide Input Voltage 90 to 305VAC, 47 to 63Hz Constant Output Current Available From 350mA To 2080mA Over Voltage, Short Circuit, Over Load Protection High Efficiency (up to 85%) Active Power Factor Correction (PFC) (92% typical) IP66 Waterproof Rating Comply with UL8750 & EN61347 Safety Regulation (Pending) Approvals: (Pending) Single Output Part Number ILPA25JUD-S208DS ILPA25JUD-S175DS ILPA25JUD-S140DS ILPA25JUD-S105DS ILPA25JUD-S070DS ILPA25JUD-S062DS ILPA25JUD-S045DS ILPA25JUD-S035DS Output Current Range (Min. / Typ. / Max.) 1976 / 2080 / 2184 mA 1663 / 1750 / 1838 mA 1330 / 1400 / 1470 mA 998 / 1050 / 1103 mA 665 / 700 / 735 mA 589 / 620 / 651 mA 428 / 450 / 473 mA 333 / 350 / 368 mA Output Voltage (Min. / Max.) 4 / 12 VDC 5 / 14 VDC 6 / 18 VDC 8 / 24 VDC 12 / 36 VDC 13 / 40 VDC 19 / 56 VDC 24 / 72 VDC Efficiency (220VAC, Full Load) 80% 80% 82% 82% 83% 83% 84% 85% Over Voltage Protection (Min. / Typ. / Max.) 13 / 15 / 17 VDC 16 / 18 / 20 VDC 21 / 23 / 25 VDC 30 / 32 / 34 VDC 46 / 48 / 50 VDC 48 / 50 / 52 VDC 71 / 73 / 75 VDC 92 / 94 / 96 VDC Max. Output Power 25W 25W 25W 25W 25W 25W 25W 25W Electrical Characteristics Parameter Input Voltage Input Frequency Output Power Range Input Current (Low Line) Input Current (High Line) High Line Inrush Current Power Factor Correction Efficiency No Load Power Dissipation Line Regulation Load Regulation Over Voltage Protection Over Load Protection Short Circuit Protection Output Overshoot / Undershoot Start Up Time Ripple & Noise (Peak to Peak) Test Conditions Operating Voltage Min. 90 47 0 Typ. Max. Unit 305 VAC 63 Hz Vin=90 to 305VAC 25 W Io=Full load, Vin=115VAC 0.32 A Io=Full load, Vin=230VAC 0.15 A Io=Full load, 25°C, Cool start, Vin=230VAC 20 A Vin=110VAC 99 % Io=Full Load, Vin=220VAC 85 % 3 W Io=Full Load 2 % Vin=230VAC 5 % Latch mode. The power unit shall return to normal operation only after the power is turn-on again. (Please refer to output table.) Hiccup mode. The power supply shall be self-recovery 1.25 Po when the fault condition is removed. No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. When power on or off 10 % Io=Full Load, Vin=100VAC 1.7 2 S Measured by 20 MHz bandwidth oscilloscope and the output paralleled a 0.1 uF ceramic capacitor and a 10 uF electrolytic capacitor. 5 % Vo Max. 70 85 Unit °C °C Hours Hours Conditions Parameter Test Conditions Operating Temperature Humidity: 10% RH to 100% RH Storage Temperature Humidity: 5% RH to 100% RH MTBF: Operation temperature at 25°C, calculated per MIL-HDBK-217F Life Time at 25°C ambient temperature Min. -20 -40 0.484M 0.079M Typ. Approvals and Compliance Parameter EMI EMS Safety UL/c-UL, CE Waterproof Standards EN55015 EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, , EN61000-4-4, , EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547 (Pending) UL8750 Compliant to UL1310 ClaST 2, UL1012, UL935, CSA-C22.2 No. 0, CSA-C22.2 No. 107.1, CSA-C22.2 No.250.0, EN61347-1,EN61347-2-13 IP66 Rating Mechanical Parameter Dimension, Net Weight Specification 78x80x25mm (3.07x3.15x0.98 inches) 200g Dimming Control Parameter Min. Typ. Max. Unit 10V Output Voltage 9.8 10V 10.2 VDC 10V Output Source Current -10 2 mA Absolute Max. Voltage on the 1~10V Input Pin -2 15 VDC Source Current on 0-10V Input Pin 0 1 mA The dimmer control may be operated from either a potentiometer or from an input signal of 0 – 10 Vdc. Two recommended implementations are provided above Notes: 1. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of t he max. output voltage for any given model). 2. If the output voltage is maintained above 50% of the maximum output voltage, the dimmer control may be operated over the entire 0-10V range with output current varying from 100% down to practically 0%. 3. If the output voltage is maintained between 33-50% of the maximum output voltage, the dimmer control may be operated over 5-10V range with output current