MBRF1035 THRU MBRF1060 FEATURES ITO-220AC 0.188 (4.77) 0.172 (4.36) 0.405 (10.27) 0.383 (9.72) 0.110 (2.80) 0.100 (2.54) 0.131 (3.39) DIA. 0.122 (3.08) 0.140 (3.56) DIA. 0.130 (3.30) 0.600 (15.5) 0.580 (14.5) 0.676 (17.2) 0.646 (16.4) PIN 1 0.350 (8.89) 0.330 (8.38) 2 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) ¨ Isolated plastic package has Underwriters Laboratory Flammability Classifications 94V-0 ¨ Metal silicon junction, majority carrier conduction ¨ Low power loss, high efficiency ¨ High current capability, low forward voltage drop ¨ High surge capability ¨ For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications ¨ Guardring for overvoltage protection ¨ High temperature soldering guaranteed: 250¡C/10 seconds, 0.25" (6.35mm) from case 0.110 (2.80) 0.100 (2.54) 0.060 (1.52) 0.037 (0.94) 0.027 (0.69) MECHANICAL DATA Case: JEDEC ITO-220AC fully overmolded plastic body Terminals: Leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounces, 1.81 grams 0.022 (0.55) 0.014 (0.36) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25¡C ambient temperature unless otherwise specified. SYMBOLS MBRF1035 MBRF1045 MBRF1050 MBRF1060 UNITS Maximum repetitive peak reverse voltage VRRM 35 45 50 60 Volts Maximum working peak reverse voltage VRWM 35 45 50 60 Volts VDC 35 45 50 60 Volts Maximum DC blocking voltage Maximum average forward rectified current I(AV) 10.0 Amps Peak repetitive forward current at TC=135¡C (square wave 20 KHZ) IFRM 20.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 150.0 Amps Peak repetitive reverse surge current (NOTE 1) IRRM Voltage rate of change (rated VR) dv/dt (SEE FIG. 1) Maximum instantaneous forward voltage at (NOTE 2) IF=10A, TC=25¡C IF=10A, TC=125¡C IF=20A, TC=25¡C IF=20A, TC=125¡C Maximum instantaneous reverse current at rated DC blocking voltage TC= 25¡C (NOTE 2) TC=125¡C Maximum thermal resistance, junction to case Operating junction temperature range VF 1.0 0.5 10,000 0.57 0.84 0.72 Amps Vms 0.80 0.70 0.95 0.85 Volts IR 0.10 15.0 mA mA RQJC 4.0 ¡C/W TJ -65 to +150 ¡C Storage temperature range TSTG -65 to +175 ¡C RMS Isolation voltage from terminals to heatsink with RH ² 30% VISOL 4500 (NOTE 3) 3500 (NOTE 4) 1500 (NOTE 5) Volts NOTES: (1) 2.0ms pulse width, f=1.0 KHZ (2) Pulse test: 300ms pulse width, 1% duty cycle (3) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset. (4) Clip mounting (on case), where leads do overlap heatsink. (5) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó). 2/18/99 www.kersemi.com RATINGS AND CHARACTERISTIC CURVES MBRF1035 THRU MBRF1060 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 12 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 10 8 6 4 150 125 100 75 50 25 0.1 2 0 PEAK FORWARD SURGE CURRENT, AMPERES 175 150 100 50 0 100 10 1 NUMBER OF CYCLES AT 60 HZ MBRF1035 - MBRF1045 MBRF1050 & MBRF1060 CASE TEMPERATURE, ¡C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 INSTANTANEOUS REVERSE CURRENT, MILLIAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 50 10 PULSE WIDTH=300ms 1% DUTY CYCLE TJ=125¡C MBRF1035 - MBRF1045 MBRF1050 & MBRF1060 10 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ=25¡C 1 0.1 TJ=125¡C 1 0.1 TJ=75¡C 0.01 TJ=25¡C MBRF1035 - MBRF1045 MBRF1050 & MBRF1060 0.01 0.001 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 60 40 100 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE JUNCTION CAPACITANCE, pF FIG. 5 - TYPICAL JUNCTION CAPACITANCE 4,000 TJ=25¡C f=1.0 MHz Vsig=50mVp-p 1,000 MBRF1035 - MBRF1045 MBRF1050 & MBRF1060 100 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, °C/W 100 10.0 1 0.1 0.01 0.1 10 1 100 t, PULSE DURATION, sec. www.kersemi.com