SIDACtor ® Protection Thyristors SLIC Protection Battrax® Series - Dual Port Negative - MS-013 Description The Dual Port Negative Battrax® Series are programmable SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. Dual port protection is provided by a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits t Dual-port protection t Low on-state voltage t Gate trigger tracking device t Does not degrade with use Agency Approvals Agency t Low voltage overshoot t Fails short circuit when surged in excess of ratings Agency File Number E133083 t Integrated diode for positive voltage surges Applicable Global Standards Pinout Designation t TIA-968-A t GR 1089 Intra-building 1 6 t TIA-968-B t IEC 61000-4-5 2 5 t ITU K.20/21 Enhanced Level t YD/T 1082 3 4 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Schematic Symbol 6 (T2) (T1) 1 5 Ground (-VREF) 2 4 (R2) (R1) 3 Electrical Characteristics Part Number Marking VDRM @lDRM=5μA VS @100V/μs V min V max IH IS mA min mA max IT VT @IT=2.2 Amps VF Capacitance* A max V max V max pF min pF max B1101UC4Lxx B1101UC4 I-VREF* *7* I-VREF* *7* 100 100 2.2 4 5 30 200 B1161UC4Lxx B1161UC4 I-VREF* *7* I-VREF* *7* 160 100 2.2 4 5 30 200 B1201UC4Lxx B1201UC4 I-VREF* *7* I-VREF* *7* 200 100 2.2 4 5 30 200 - VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1 & 6) to Ground (pin 5) and Ring (pin 3 & 4) to Ground (pin 5) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. * Off-state capacitance (CO) is measured across pins 1 & 5, 3 & 5, 4 & 5, and 6 & 5 at 1 MHz with a 2V bias. 126 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM di/dt 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 50/60 Hz A min A min A min A min A min A min A min A min A min A min A/μs max 50 500 400 200 150 200 175 100 200 50 500 1 C 1 1 1 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ *PP rating assumes VREFFRVBMT 7 - The device must initially be in thermal equilibrium with -40°C < TJ < ¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Modified MS-013 Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W 6 5 4 1 2 3 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I V VREF VS VDRM IF VT -V +V IDRM IH IS IT IPP Waveform = tr x td 50 Half Value 0 1.8 10 IH 8 25 °C Ratio of IH (TC = 25ºC) 2.0 12 4 t – Time (μs) Normalized DC Holding Current vs. Case Temperature 14 6 td tr PIN 3 CONNECTED TO VREF Normalized VS Change vs. Junction Temperature Percent of VS Change – % 100 0 PIN CONNECTED TO GROUND Pin 51-2: PIN TOGROUND VREF PIN22CONNECTED CONNECTED TO -I tr = rise time to peak value td = decay time to half value Peak Value 2 0 -4 -6 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 127 Revised: February 22, 2011 160 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) Pre Heat - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. - Temperature (TL) (Liquidus) Reflow Figure 1 TP TL ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition tL TS(max) Ramp-down Preheat TS(min) tS ¡$ 25 Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed time to peak temperature (t 25ºC to peak) Time ¡$ Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VDC Peak ¡$PS ¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP ¡$ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC ¡$ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP ¡$ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$ TFDT.*-45% .FUIPE Body Material UL recognized epoxy meeting flammability classification 94V-0 Moisture Sensitivity Level 3) ¡$ IST SFnPXDZDMFT ¡$1FBL +&%&$+45% -FWFM Part Marking Part Numbering B1 xx 1 U C 4 L xx TYPE B1: Negative Battrax SIDACtor HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXXX RoHS COMPLIANT DUAL PORT IPP RATING Date Code XXXXX PACKAGE TYPE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code (Refer to Electrical Characteristics Table) 128 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C A B C D E F G H J K BSC* 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7º TYP J 7º TYP A G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F MIN Length of Flat 7º TYP K Detail A B Inches Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 --0.143 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 --3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) 129 Revised: February 22, 2011 20.000 ± .030 (508.00 ± 0.76) Millimeters