ON MC74HC245ADWG Octal 3-state noninverting bus transceiver Datasheet

MC74HC245A
Octal 3-State Noninverting
Bus Transceiver
High−Performance Silicon−Gate CMOS
The MC74HC245A is identical in pinout to the LS245. The device
inputs are compatible with standard CMOS outputs; with pull−up
resistors, they are compatible with LSTTL outputs.
The HC245A is a 3−state noninverting transceiver that is used for
2−way asynchronous communication between data buses. The device
has an active−low Output Enable pin, which is used to place the I/O
ports into high−impedance states. The Direction control determines
whether data flows from A to B or from B to A.
http://onsemi.com
SOIC−20
DW SUFFIX
CASE 751D
Features
•
•
•
•
•
•
•
•
•
Output Drive Capability: 15 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1 mA
High Noise Immunity Characteristic of CMOS Devices
In Compliance with the Requirements Defined by JEDEC Standard
No. 7 A
Chip Complexity: 308 FETs or 77 Equivalent Gates
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free and are RoHS Compliant
LOGIC DIAGRAM
A1
A2
A3
A
DATA
PORT
A4
A5
A6
A7
A8
DIRECTION
OUTPUT
ENABLE
PIN ASSIGNMENT
DIRECTION
1
20
VCC
A1
2
19
OUTPUT
ENABLE
A2
3
18
B1
A3
4
17
B2
A4
5
16
B3
A5
6
15
B4
A6
7
14
B5
A7
8
13
B6
A8
9
12
B7
10
11
B8
GND
2
18
3
17
4
16
5
15
6
14
7
13
8
12
9
11
TSSOP−20
DT SUFFIX
CASE 948E
B1
MARKING DIAGRAMS
B2
B3
20
B4
B
DATA
PORT
B5
B6
20
HC
245A
ALYWG
G
HC245A
AWLYYWWG
B7
1
B8
1
SOIC−20
1
A
WL, L
YY, Y
WW, W
G or G
19
PIN 10 = GND
PIN 20 = VCC
TSSOP−20
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
© Semiconductor Components Industries, LLC, 2014
November, 2014 − Rev. 16
1
Publication Order Number:
MC74HC245A/D
MC74HC245A
FUNCTION TABLE
Control Inputs
Output
Enable
Direction
L
L
Data Transmitted from Bus B to Bus A
L
H
Data Transmitted from Bus A to Bus B
H
X
Buses Isolated (High−Impedance State)
Operation
X = don’t care
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
VCC
DC Supply Voltage
VIN
DC Input Voltage
VOUT
DC Output Voltage
(Note 2)
Value
Unit
−0.5 to +7.0
V
−0.5 to VCC + 0.5
V
−0.5 to VCC + 0.5
V
IIK
DC Input Diode Current
±20
mA
IOK
DC Output Diode Current
±35
mA
IOUT
DC Output Sink Current
±35
mA
ICC
DC Supply Current per Supply Pin
±75
mA
IGND
DC Ground Current per Ground Pin
±75
mA
TSTG
Storage Temperature Range
−65 to +150
_C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
260
_C
TJ
Junction Temperature Under Bias
+150
_C
qJA
Thermal Resistance
SOIC
TSSOP
96
128
_C/W
PD
Power Dissipation in Still Air at 85_C
SOIC
TSSOP
500
450
mW
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ILATCHUP
Level 1
Oxygen Index: 30% to 35%
ESD Withstand Voltage
Latchup Performance
UL 94 V−0 @ 0.125 in
Human Body Model (Note 3)
Machine Model (Note 4)
Charged Device Model (Note 5)
Above VCC and Below GND at 85_C (Note 6)
u2000
u200
u1000
V
±300
mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 20 ounce copper trace with no air flow.
2. IO absolute maximum rating must observed.
3. Tested to EIA/JESD22−A114−A.
4. Tested to EIA/JESD22−A115−A.
5. Tested to JESD22−C101−A.
6. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Vin, Vout
Parameter
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature, All Package Types
tr, tf
Input Rise and Fall Time
(Figure 1)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
Min
Max
Unit
2.0
6.0
V
0
VCC
V
–55
+125
_C
0
0
0
1000
500
400
ns
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
http://onsemi.com
2
MC74HC245A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
Guaranteed Limit
VCC
V
–55 to
25_C
Symbol
Parameter
v 85_C
v 125_C
Unit
VIH
Minimum High−Level Input Voltage
Vout = VCC – 0.1 V
|Iout| v 20 mA
2.0
3.0
4.5
6.0
1.5
2.1
3.15
4.2
1.5
2.1
3.15
4.2
1.5
2.1
3.15
4.2
V
VIL
Maximum Low−Level Input Voltage
Vout = 0.1 V
|Iout| v 20 mA
2.0
3.0
4.5
6.0
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
V
VOH
Minimum High−Level Output
Voltage
Vin = VIH
|Iout| v 20 mA
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
Vin = VIH |Iout| v 2.4 mA
|Iout| v 6.0 mA
|Iout| v 7.8 mA
3.0
4.5
6.0
2.48
3.98
5.48
2.34
3.84
5.34
2.2
3.7
5.2
Vin = VIL
|Iout| v 20 mA
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
Vin = VIL |Iout| v 2.4 mA
|Iout| v 6.0 mA
|Iout| v 7.8 mA
3.0
4.5
6.0
0.26
0.26
0.26
0.33
0.33
0.33
0.4
0.4
0.4
VOL
Test Conditions
Maximum Low−Level Output
Voltage
V
Iin
Maximum Input Leakage Current
Vin = VCC or GND
6.0
±0.1
±1.0
±1.0
mA
IOZ
Maximum Three−State Leakage
Current
Output in High−Impedance State
Vin = VIL or VIH
Vout = VCC or GND
6.0
±0.5
±5.0
±10
mA
ICC
Maximum Quiescent Supply Current (per Package)
Vin = VCC or GND
Iout = 0 mA
6.0
4.0
40
160
mA
VCC
V
–55 to
25_C
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Guaranteed Limit
v 85_C
v 125_C
Unit
tPLH,
tPHL
Maximum Propagation Delay,
A to B, B to A
(Figures 1 and 3)
2.0
3.0
4.5
6.0
75
55
15
13
95
70
19
16
110
80
22
19
ns
tPLZ,
tPHZ
Maximum Propagation Delay,
Direction or Output Enable to A or B
(Figures 2 and 4)
2.0
3.0
4.5
6.0
110
90
22
19
140
110
28
24
165
130
33
28
ns
tPZL,
tPZH
Maximum Propagation Delay,
Output Enable to A or B
(Figures 2 and 4)
2.0
3.0
4.5
6.0
110
90
22
19
140
110
28
24
165
130
33
28
ns
tTLH,
tTHL
Maximum Output Transition Time,
Any Output
(Figures 1 and 3)
2.0
3.0
4.5
6.0
60
23
12
10
75
27
15
13
90
32
18
15
ns
Symbol
Parameter
Cin
Maximum Input Capacitance (Pin 1 or Pin 19)
−
10
10
10
pF
Cout
Maximum Three−State I/O Capacitance
(I/O in High−Impedance State)
−
15
15
15
pF
Typical @ 25°C, VCC = 5.0 V
CPD
Power Dissipation Capacitance (Per Transceiver Channel) (Note 7)
7. Used to determine the no−load dynamic power consumption: PD = CPD VCC2 f + ICC VCC .
http://onsemi.com
3
40
pF
MC74HC245A
ORDERING INFORMATION
Package
Shipping†
MC74HC245ADWG
SOIC−20 WIDE
(Pb−Free)
38 Units / Rail
NLV74HC245ADWG*
SOIC−20 WIDE
(Pb−Free)
38 Units / Rail
MC74HC245ADWR2G
SOIC−20 WIDE
(Pb−Free)
1000 Tape & Reel
NLV74HC245ADWR2G*
SOIC−20 WIDE
(Pb−Free)
1000 Tape & Reel
MC74HC245ADTG
TSSOP−20
(Pb−Free)
75 Units / Rail
NLV74HC245ADTG*
TSSOP−20
(Pb−Free)
75 Units / Rail
MC74HC245ADTR2G
TSSOP−20
(Pb−Free)
2500 Tape & Reel
NLV74HC245ADTR2G*
TSSOP−20
(Pb−Free)
2500 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
VCC
DIRECTION
50%
GND
VCC
tr
tf
INPUT
A OR B
VCC
90%
50%
10%
tPHL
A OR B
90%
50%
10%
GND
tPLZ
A OR B
HIGH
IMPEDANCE
50%
tPZH
tPHZ
10%
VOL
90%
VOH
50%
HIGH
IMPEDANCE
tTHL
tTLH
Figure 1. Switching Waveform
Figure 2. Switching Waveform
TEST POINT
TEST POINT
OUTPUT
DEVICE
UNDER
TEST
50%
tPZL
GND
tPLH
OUTPUT
B OR A
OUTPUT
ENABLE
OUTPUT
CL *
DEVICE
UNDER
TEST
1 kW
CL *
CONNECT TO VCC WHEN
TESTING tPLZ AND tPZL.
CONNECT TO GND WHEN
TESTING tPHZ AND tPZH.
*Includes all probe and jig capacitance
*Includes all probe and jig capacitance
Figure 3. Test Circuit
Figure 4. Test Circuit
http://onsemi.com
4
MC74HC245A
A1
2
18
A2
3
17
A3
A5
OUTPUT ENABLE
B7
9
11
DIRECTION
B6
8
12
A8
B5
7
13
A7
B4
6
14
A6
B3
5
15
A
DATA
PORT
B2
4
16
A4
B1
1
19
Figure 5. Expanded Logic Diagram
http://onsemi.com
5
B8
B
DATA
PORT
MC74HC245A
PACKAGE DIMENSIONS
TSSOP−20
DT SUFFIX
CASE 948E−02
ISSUE C
20X
0.15 (0.006) T U
2X
K REF
0.10 (0.004)
S
L/2
20
M
T U
S
V
K
K1
ÍÍÍÍ
ÍÍÍÍ
ÍÍÍÍ
S
J J1
11
B
−U−
L
PIN 1
IDENT
SECTION N−N
0.25 (0.010)
N
1
10
M
0.15 (0.006) T U
S
N
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION:
MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
F
DETAIL E
−W−
C
G
D
H
DETAIL E
0.100 (0.004)
−T− SEATING
PLANE
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
6
MILLIMETERS
MIN
MAX
6.40
6.60
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.27
0.37
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.252
0.260
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.011
0.015
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0_
8_
MC74HC245A
PACKAGE DIMENSIONS
SOIC−20
DW SUFFIX
CASE 751D−05
ISSUE G
20
11
X 45 _
h
H
M
E
0.25
10X
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF B
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
q
A
B
M
D
1
10
20X
B
B
0.25
M
T A
S
B
S
L
A
18X
e
A1
DIM
A
A1
B
C
D
E
e
H
h
L
q
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
12.65
12.95
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0_
7_
SEATING
PLANE
C
T
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HC245A/D
Similar pages