ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Optocoupler, Phototransistor Output (Dual, Quad Channel) Features • • • • Dual Channel Current Transfer Ratio at IF = 10 mA Isolation Test Voltage, 5300 VRMS Lead-free component Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC A 1 8 E C 2 7 C C 3 6 C A 5 E 4 Agency Approvals • UL1577, File No. E52744 System Code H or J, Double Protection • CSA 93751 • BSI IEC60950 IEC60065 • DIN EN 60747-5-2 (VDE0884) DIN EN 60747-5-5 pending Available with Option 1 • FIMKO Quad Channel A 1 16 E C 2 15 C C 3 14 C A 4 13 E A 5 12 E C 6 11 C Description C 7 10 C The ILD1/ 2/ 5/ ILQ1/ 2/ 5 are optically coupled isolated pairs employing GaAs infrared LEDs and silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the drive while maintaining a high degree of electrical isolation between input and output. The ILD1/ 2/ 5/ ILQ1/ 2/ 5 are espe- A 8 9 E cially designed for driving medium-speed logic and can be used to eliminate troublesome ground loop and noise problems. Also these couplers can be used to replace relays and transformers in many digital interface applications such as CTR modulation. The ILD1/ 2/ 5 has two isolated channels in a single DIP package and the ILQ1/ 2/ 5 has four isolated channels per package. e3 i179012 Pb Pb-free Order Information Part Remarks ILD1 CTR > 20 %, DIP-8 ILQ1 CTR > 20 %, DIP-16 ILD2 CTR > 100 %, DIP-8 ILQ2 CTR > 100 %, DIP-16 ILD5 CTR > 50 %, DIP-8 ILQ5 CTR > 50 %, DIP-16 ILD1-X007 CTR > 20 %, SMD-8 (option 7) ILD1-X009 CTR > 20 %, SMD-8 (option 9) ILD2-X006 CTR > 100 %, DIP-8 400 mil (option 6) ILD2-X007 CTR > 100 %, SMD-8 (option 7) ILD2-X009 CTR > 100 %, SMD-8 (option 9) ILD5-X009 CTR > 50 %, SMD-8 (option 9) ILQ1-X009 CTR > 20 %, SMD-16 (option 9) ILQ2-X009 CTR > 100 %, SMD-16 (option 9) For additional information on the available options refer to Option Information. Document Number 83646 Rev. 1.4, 05-Nov-04 www.vishay.com 1 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Absolute Maximum Ratings Tamb = 25 °C, unless otherwise specified Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability. Input Symbol Value Reverse voltage Parameter Test condition VR 6.0 V Forward current IF 60 mA Surge current IFSM 2.5 A Power dissipation Pdiss 100 mW 1.3 mW/°C Derate linearly from 25 °C Unit Output Parameter Test condition Collector-emitter reverse voltage Part Symbol Value Unit ILD1 VCER 50 V ILQ1 VCER 50 V ILD2 VCER 70 V ILQ2 VCER 70 V ILD5 VCER 70 V ILQ5 VCER 70 V IC 50 mA IC 400 mA Pdiss 200 mW 2.6 mW/°C Collector current t < 1.0 ms Power dissipation Derate linearly from 25 °C Coupler Parameter Test condition Symbol Value Unit VISO 5300 VRMS Creepage ≥ 7.0 mm Clearance ≥ 7.0 mm Isolation test voltage (between emitter and detector referred to standard climate 25 °C/ 50 % RH, DIN 50014) Isolation resistance VIO = 500 V, Tamb = 25 °C RIO 1012 Ω VIO = 500 V, Tamb = 100 °C RIO 10 11 Ω Ptot 250 mW 3.3 mW/°C °C Package power dissipation Derate linearly from 25 °C Storage temperature Tstg - 40 to + 150 Operating temperature Tamb - 40 to + 100 °C Tj 100 °C Tsld 260 °C Junction temperature Soldering temperature www.vishay.com 2 2.0 mm from case bottom Document Number 83646 Rev. 1.4, 05-Nov-04 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Electrical Characteristics Tamb = 25 °C, unless otherwise specified Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Input Typ. Max Forward voltage Parameter IF = 60 mA Test condition VF 1.25 1.65 V Reverse current VR = 6.0 V IR 0.01 10 µA Capacitance VR = 0 V, f = 1.0 MHz Thermal resistance, junction to lead Symbol Min Unit CO 25 pF TthJL 750 K/W Output Parameter Test condition Symbol Min Typ. Max Unit 5.0 50 nA 0.25 0.4 V Collector-emitter capacitance VCE = 5.0 V, f = 1.0 MHz CCE 6.8 Collector-emitter leakage current VVCE = 10 V ICEO Saturation voltage, collectoremitter ICE = 1.0 mA, IB = 20 µA VCESAT pF DC forward current gain VCE = 10 V, IB = 20 µA HFE 200 650 1800 DC forward current gain saturated VCE = 0.4 V, IB = 20 µA HFEsat 120 400 600 Thermal resistance, junction to lead Rthjl 500 K/W Coupler Parameter Capacitance (input-output) Test condition VIO = 0 V, f = 1.0 MHz Symbol Min CIO Typ. Max Unit 0.8 pF Current Transfer Ratio Parameter Current Transfer Ratio (collector-emitter saturated) Current Transfer Ratio (collector-emitter) Document Number 83646 Rev. 1.4, 05-Nov-04 Test condition IF = 10 mA, VCE = 0.4 V IF = 10 mA, VCE = 10 V Part Symbol ILD1 ILQ1 CTRCEsat Min Typ. 75 Max Unit % ILD2 ILQ2 CTRCEsat 170 % ILD5 ILQ5 CTRCEsat 100 % ILD1 ILQ1 CTRCE 20 80 300 % ILD2 ILQ2 CTRCE 100 200 500 % ILD5 ILQ5 CTRCE 50 130 400 % www.vishay.com 3 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Typical Switching Times Non-saturated Switching Timing Parameter Current Delay Symbol IF tD Rise time Storage Fall time Propagation H-L Propagation L-H tPHL tPLH VCE = 5.0 V, RL = 75 Ω, 50 % of VPP Test condition tr tS tf Unit mA µs µs µs µs µs µs ILD1 ILQ1 20 0.8 1.9 0.2 1.4 0.7 1.4 ILD2 ILQ2 5.0 1.7 2.6 0.4 2.2 1.2 2.3 ILD5 ILQ5 10 1.7 2.6 0.4 2.2 1.1 2.5 Rise time Storage Fall time Propagation H-L Propagation L-H tPHL tPLH Saturated Switching Timing Parameter Current Delay Symbol IF tD Test condition VCE = 0.4 V, RL = 1.0 kΩ, VCC = 5.0 V, VTH = 1.5 V tr tS tf Unit mA µs µs µs µs µs µs ILD1 ILQ1 20 0.8 1.2 7.4 7.6 1.6 8.6 ILD2 ILQ2 5.0 1.0 2.0 5.4 13.5 5.4 7.4 ILD5 ILQ5 10 1.7 7.0 4.6 20 2.6 7.2 Common Mode Transient Immunity Parameter Test condition Symbol Min Typ. Max Unit Common mode rejection, output high VCM = 50 VP-P, RL = 1.0 kΩ, IF = 0 mA CMH 5000 V/µs Common mode rejection, output low VCM = 50 VP-P, RL = 1.0 kΩ, IF = 10 mA CML 5000 V/µs CCM 0.01 pF Common mode coupling capacitance www.vishay.com 4 Document Number 83646 Rev. 1.4, 05-Nov-04 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Typical Characteristics (Tamb = 25 °C unless otherwise specified) IF VCC=5 V IF=10 mA VO R L=75 Ω F=10 KHz, DF=50% VO tD tR tPLH VTH=1.5 V tF tS tPHL iild1_01 iild1_04 Figure 1. Non-saturated Switching Schematic Figure 4. Saturated Switching Timing 1.4 t PHL VO tPLH tS 50% V F - Forward Voltage - V IF 1.3 TA = -55°C 1.2 TA = 25°C 1.1 1.0 0.9 TA = 100°C 0.8 0.7 .1 iild1_02 tD tF tR 1 10 I F - Forward Current - mA 100 iild1_05 F=10 KHz, DF=50% VCC=5 V RL IF=10 mA VO Figure 5. Normalized Non-Saturated and Saturated CTR vs. LED Current CTRNF - Normalized CTR Factor Figure 2. Non-saturated Switching Timing iild1_03 1.5 Normalized to: VCE = 10 V, IF = 10 mA TA= 25°C CTRce(sat) VCE = 0.4 V 1.0 NCTR 0.5 NCTR(SAT) 0.0 .1 1 10 100 I F - LED Current - mA iild1_06 Figure 3. Saturated Switching Schematic Document Number 83646 Rev. 1.4, 05-Nov-04 Figure 6. Normalized Non-Saturated and Saturated CTR vs. LED Current www.vishay.com 5 ILD1/ 2/ 5 / ILQ1/ 2/ 5 1.5 35 Normalized to: VCE = 10 V, IF = 10 mA, TA= 25°C ˇ CTRce(sat) VCE = 0.4 V 1.0 ICE - Collector Current - mA TA= 50°C NCTR 0.5 NCTR(SAT) 30 25 50°C 20 15 5 0 .1 1 10 100 0 10 I F - LED Current - mA iild1_07 20 40 30 50 60 IF - LED Current - mA iild1_10 Figure 7. Normalized Non-Saturated and Saturated CTR vs. LED Current Figure 10. Collector-Emitter Current vs. Temperature and LED Current 1.5 10 5 ICEO - Collector-Emitter - nA CTR - Normalized CTR Factor 85°C 10 0.0 Normalized to: VCE = 10 V, IF = 10 mA TA= 25°C 1.0 CTRce(sat) VCE = 0.4 V TA= 70°C NCTR 0.5 NCTR(SAT) .1 1 10 10 4 10 3 10 2 Vce = 10 V 10 1 Typical 10 0 10 -1 10 -2 -20 0.0 100 0 20 40 60 80 100 TA - Ambient Temperature - °C I F - LED Current - mA iild1_08 iild1_11 Figure 8. Normalized Non-Saturated and Saturated CTR vs. LED Current Figure 11. Collector-Emitter Leakage Current vs.Temp. 1000 1.5 Normalized to: V CE = 10 V, I F = 10 mA, TA = 25°C CTRce(sat) VCE = 0.4 V 1.0 tpLH - Propagation Low-High µs NCTR - Normalized CTR 70°C 25°C TA = 85°C NCTR 0.5 NCTR(SAT) 0.0 .1 1 10 IF - LED Current - mA 2.5 Ta = 25°C, IF = 10 mA Vcc = 5 V, Vth = 1.5 V tpHL 100 2.0 10 1.5 tpLH 1 100 tpHL - Propagation High-Low µs CTRNF - Normalized CTR Factor Vishay Semiconductors 1.0 .1 1 10 100 RL - Collector Load Resistor - kΩ iild1_09 Figure 9. Normalized Non-Saturated and Saturated CTR vs. LED Current www.vishay.com 6 iild1_12 Figure 12. Propagation Delay vs. Collector Load Resistor Document Number 83646 Rev. 1.4, 05-Nov-04 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Package Dimensions in Inches (mm) pin one ID 4 3 2 1 5 6 7 8 .255 (6.48) .268 (6.81) ISO Method A .379 (9.63) .390 (9.91) .030 (0.76) .045 (1.14) 4° typ. .300 (7.62) typ. .031 (0.79) .130 (3.30) .150 (3.81) .050 (1.27) .230(5.84) .110 (2.79) .250(6.35) .130 (3.30) 10° .020 (.51 ) .035 (.89 ) .100 (2.54) typ. .018 (.46) .022 (.56) 3°–9° .008 (.20) .012 (.30) i178006 Package Dimensions in Inches (mm) pin one ID 8 7 6 5 4 3 2 1 .255 (6.48) .265 (6.81) 9 10 11 12 13 14 15 16 ISO Method A .779 (19.77 ) .790 (20.07) .030 (.76) .045 (1.14) .300 (7.62) typ. .031(.79) .130 (3.30) .150 (3.81) 4° .018 (.46) .022 (.56) .020(.51) .035 (.89) .100 (2.54)typ. .050 (1.27) 10° typ. 3°–9° .008 (.20) .012 (.30) .110 (2.79) .130 (3.30) .230 (5.84) .250 (6.35) i178007 Document Number 83646 Rev. 1.4, 05-Nov-04 www.vishay.com 7 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Option 6 Option 7 .407 (10.36) .391 (9.96) .307 (7.8) .291 (7.4) .300 (7.62) TYP. Option 9 .375 (9.53) .395 (10.03) .300 (7.62) ref. .028 (0.7) MIN. .180 (4.6) .160 (4.1) .0040 (.102) .0098 (.249) .315 (8.0) MIN. .014 (0.35) .010 (0.25) .400 (10.16) .430 (10.92) www.vishay.com 8 .331 (8.4) MIN. .406 (10.3) MAX. .012 (.30) typ. .020 (.51) .040 (1.02) .315 (8.00) min. 15° max. 18450 Document Number 83646 Rev. 1.4, 05-Nov-04 ILD1/ 2/ 5 / ILQ1/ 2/ 5 Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423 Document Number 83646 Rev. 1.4, 05-Nov-04 www.vishay.com 9