HT604L/HT614/HT692 318 Series of Decoders Features · Operating voltage: 2.4V~12V · Built-in oscillator needs only a 5% resistor · Low power and high noise immunity CMOS · Valid transmission indicator technology · Easy interface with an RF or an infrared transmission · Low standby current medium · Capable of decoding 18 bits of information · Minimal external components · 9~10 address pins · Pair with Holtek¢s 318 series of encoders · 2~8 data pins · HT604L/HT614: 20-pin DIP/SOP package · Trinary address setting HT692: 18-pin DIP package · Two times of receiving check Applications · Burglar alarm system · Car alarm system · Smoke and fire alarm system · Security system · Garage door controllers · Cordless telephones · Car door controllers · Other remote control systems General Description The 318 decoders are a series of CMOS LSIs for remote control system applications. They are paired with the 318 series of encoders. For proper operation, a pair of encoder/decoder pair with the same number of address and data format should be selected (refer to the encoder/decoder cross reference tables). are encountered, the input data codes are decoded and then transferred to the output pins. The VT pin also goes high to indicate a valid transmission. The 318 decoders are capable of decoding 18 bits of information that consists of N bits of address and 18-N bits of data. To meet various applications they are arranged to provide a number of data pins whose range is from 0 to 8 and an address pin whose range is from 8 to 18. In addition, the 318 decoders provide various combinations of address/data number in different packages. The 318 series of decoders receive serial address and data from that series of encoders that are transmitted by a carrier using an RF or an IR transmission medium. It then compares the serial input data twice continuously with its local address. If no errors or unmatched codes Selection Table Function Address No. Part No. Data No. Type VT Oscillator Trigger Package HT604L 10 4 L Ö RC oscillator DIN active ²Hi² 20DIP/SOP HT614 10 4 M Ö RC oscillator DIN active ²Hi² 20DIP/SOP HT692 10 2 M Ö RC oscillator DIN active ²Hi² 18DIP Note: Data type: M stands for momentary type data output. L stands for latch type data output. VT can be used as a momentary data output. Rev. 1.10 1 January 24, 2003 HT604L/HT614/HT692 Block Diagram O S C 2 O S C 1 O s c illa to r D IN D iv id e r B u ffe r D a ta S h ift R e g is te r L a tc h C ir c u it C o m p a ra to r C o n tr o l L o g ic D a ta D e te c to r S y n c . D e te c to r C o m p a ra to r T r a n s m is s io n G a te C ir c u it V T B u ffe r A d d re s s Note: D a ta V D D V S S The address/data pins are available in various combinations (refer to the address/data table). Pin Assignment Latch Series Momentary Series 1 0 -A d d re s s 4 -D a ta 1 0 -A d d re s s 2 -D a ta 1 0 -A d d re s s 4 -D a ta A 1 1 1 2 0 V D D A 1 1 1 2 0 V D D D 1 2 2 1 9 A 9 D 1 2 2 1 9 A 9 A 1 1 1 1 8 V D D D 1 3 3 1 8 A 8 D 1 3 3 1 8 A 8 A 1 2 2 1 7 A 9 D 1 4 4 1 7 A 7 D 1 4 4 1 7 A 7 1 6 A 8 5 1 6 A 6 D 1 5 5 1 6 A 6 D 1 4 D 1 5 3 D 1 5 V T 4 1 5 A 7 6 1 5 A 4 V T 6 1 5 A 4 V T 5 1 4 A 6 D IN 7 1 4 A 3 D IN 7 1 4 A 3 D IN 6 1 3 A 3 O S C 2 O S C 1 8 1 3 A 2 8 1 3 A 2 O S C 2 7 1 2 A 2 9 1 2 A 1 O S C 2 O S C 1 9 1 2 A 1 O S C 1 8 1 1 A 1 1 0 1 1 A 0 V S S 1 0 1 1 A 0 V S S 9 1 0 A 0 V S S H T 6 0 4 L 2 0 D IP -A /S O P -A H T 6 1 4 2 0 D IP -A /S O P -A H T 6 9 2 1 8 D IP -A Pin Description I/O Internal Connection A0~A12 I TRANSMISSION GATE D10~D17 O CMOS OUT DIN I CMOS IN VT O CMOS OUT OSC1 I OSCILLATOR Oscillator input pin OSC2 O OSCILLATOR Oscillator output pin VSS ¾ ¾ Negative power supply, ground VDD ¾ ¾ Positive power supply Pin Name Rev. 1.10 Description Input pins for address A0~A12 setting They can be externally set to VDD, VSS or left open. Output data pins Serial data input pin Valid transmission, active high 2 January 24, 2003 HT604L/HT614/HT692 Approximate Internal Connections T R A N S M IS S IO N G A T E C M O S O U T C M O S IN O S C IL L A T O R E N O S C 1 O S C 2 Absolute Maximum Ratings Supply Voltage ............................VSS-0.3V to VSS+13V Storage Temperature ............................-50°C to 125°C Input Voltage..............................VSS-0.3V to VDD+0.3V Operating Temperature...........................-20°C to 75°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Electrical Characteristics Symbol Parameter VDD Operating Voltage ISTB Standby Current Ta=25°C Test Conditions Min. Typ. Max. Unit 3 ¾ 12 V ¾ 0.1 1 mA ¾ 2 4 mA ¾ 0.2 1 mA VOH=4.5V -0.5 -1 ¾ mA VOL=0.5V 0.25 1 ¾ mA VOH=4.5V -2 -4 ¾ mA VOL=0.5V 0.25 1 ¾ mA VDD Conditions ¾ ¾ 5V Oscillator stops 12V IDD Operating Current No load, fOSC=100kHz 5V Data Output Source Current (D10~D17) IO 5V Data Output Sink Current (D10~D17) VT Output Source Current IVT 5V VT Output Sink Current VIH ²H² Input Voltage 5V ¾ 3.5 ¾ 5 V VIL ²L² Input Voltage 5V ¾ 0 ¾ 1 V fOSC Oscillator Frequency 10V ¾ 100 ¾ kHz Rev. 1.10 ROSC=330kW 3 January 24, 2003 HT604L/HT614/HT692 Functional Description Flowchart Operation 18 The 3 series of decoders provide various combinations of address and data pins in different packages. It is paired with the 318 series of encoders. The decoders receive data transmitted by the encoders and interpret the first N bits of the code period as address and the last 18-N bits as data (where N is the address code number). A signal on the DIN pin then activates the oscillator which in turns decodes the incoming address and data. The decoders will check the received address twice continuously. If all the received address codes match the contents of the decoder¢s local address, the 18-N bits of data are decoded to activate the output pins, and the VT pin is set high to indicate a valid transmission. That will last until the address code is incorrect or no signal has been received. The output of the VT pin is high only when the transmission is valid. Otherwise it is always low. P o w e r o n S ta n d b y m o d e N o D is a b le V T & ig n o r e th e r e s t o f th is w o r d C o d e in ? Y e s N o A d d r e s s b its m a tc h e d ? Y e s S to re d a ta M a tc h p r e v io u s s to r e d d a ta ? Output Type N o Y e s There are two types of output to select from: · Momentary type 2 tim e s o f c h e c k in g c o m p le te d ? N o The data outputs follow the encoder during a valid transmission and then reset. Y e s · Latch type L a tc h /M o m e n ta ry d a ta to o u tp u t & a c tiv a te V T The data outputs follow the encoder during a valid transmission, and are then latched in this state until the next valid transmission occurs. N o A d d re s s o r d a ta e rro r ? Y e s Note: The oscillator is disabled in the standby state and activated as long as a logic ²high² signal is applied to the DIN pin. i.e., the DIN should be kept ²low² if there is no signal input. Decoder timing E n c o d e r T r a n s m is s io n E n a b le < 1 w o rd E n c o d e r D a ta O u t T r a n s m itte d C o n tin u o u s ly 3 w o rd s D e c o d e r V T 2 w o rd s c h e c k 2 1 4 3 w o rd s 2 c lo c k s 1 4 c lo c k s c h e c k M o m e n ta ry D a ta O u t 1 /2 c lo c k p e r io d 1 /2 c lo c k p e r io d L a tc h e d D a ta O u t Rev. 1.10 4 January 24, 2003 HT604L/HT614/HT692 Encoder/Decoder Selection Tables · Latch type of data output Package Part No. HT604L Data Pins Address Pins 4 VT Pair Encoder Ö 10 Encoder DIP SOP HT600 20 20 HT6207 20 ¾ Decoder SKDIP DIP SOP SKDIP ¾ 20 20 ¾ · Momentary type of data output Package Part No. Data Pins Address Pins VT HT692 2 10 Ö HT614 4 10 Ö Pair Encoder Encoder Decoder DIP SOP SKDIP DIP SOP SKDIP HT680 18 ¾ ¾ 18 ¾ ¾ HT600 20 20 HT6207 20 ¾ ¾ 20 20 ¾ Address/Data Sequence The following provides a table of address/data sequence for various models of the 318 series decoders. Part No. Address/Data Bits 0~3 4 5 6~9 10 11 12 13 14 15 16 17 HT604L A0~A3 A4 ¾ A6~A9 ¾ A11 D12 D13 D14 D15 ¾ ¾ HT614 A0~A3 A4 ¾ A6~A9 ¾ A11 D12 D13 D14 D15 ¾ ¾ HT692 A0~A3 ¾ ¾ A6~A9 ¾ A11 A12 ¾ D14 D15 ¾ ¾ Note: ²¾² is a dummy code which is left ²open² and not bonded out. Oscillator Frequency vs. Supply Voltage fo s c (S c a le ) R o s c (9 ) 3 .0 0 2 .7 5 1 2 0 k 2 .5 0 2 .2 5 2 .0 0 1 5 0 k 1 .7 5 1 8 0 k 1 .5 0 2 2 0 k 1 .2 5 2 7 0 k (1 0 0 k H z ) 1 .0 0 3 3 0 k 3 9 0 k 4 7 0 k 5 6 0 k 6 8 0 k 8 2 0 k 1 M 1 .5 M 2 M 0 .7 5 0 .5 0 0 .2 5 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 2 .5 V D D (V D C ) The recommended oscillator frequency is fOSCD (decoder) @ fOSCE (encoder) Rev. 1.10 5 January 24, 2003 HT604L/HT614/HT692 Application Circuits R e c e iv e r C ir c u it R e c e iv e r C ir c u it V 3 4 5 6 7 R o s c 9 8 1 A 1 1 2 A 1 2 A 9 D 1 4 A 8 D 1 5 A 7 V T A 6 D IN A 3 O S C 2 A 2 O S C 1 A 1 V S S A 0 V D D 1 1 8 2 1 7 3 1 6 4 1 5 5 1 4 6 1 3 7 1 2 8 1 1 R o s c 1 0 9 1 0 H T 6 9 2 Rev. 1.10 V D D A 1 1 V D D D 1 2 A 9 D 1 3 A 8 D 1 4 A 7 D 1 5 A 6 V T A 4 D IN A 3 O S C 2 A 2 O S C 1 A 1 V S S A 0 D D 2 0 1 9 1 8 1 7 1 6 1 5 1 4 1 3 1 2 1 1 H T 6 1 4 /H T 6 0 4 L 6 January 24, 2003 HT604L/HT614/HT692 Package Information 18-pin DIP (300mil) Outline Dimensions A B 1 8 1 0 1 9 H C D E = G I F Symbol A Rev. 1.10 Dimensions in mil Min. Nom. Max. 895 ¾ 915 B 240 ¾ 260 C 125 ¾ 135 D 125 ¾ 145 E 16 ¾ 20 F 50 ¾ 70 G ¾ 100 ¾ H 295 ¾ 315 I 335 ¾ 375 a 0° ¾ 15° 7 January 24, 2003 HT604L/HT614/HT692 20-pin DIP (300mil) Outline Dimensions A B 2 0 1 1 1 1 0 H C D E Symbol Rev. 1.10 F = G I Dimensions in mil Min. Nom. Max. A 1020 ¾ 1045 B 240 ¾ 260 C 125 ¾ 135 D 125 ¾ 145 E 16 ¾ 20 F 50 ¾ 70 G ¾ 100 ¾ H 295 ¾ 315 I 335 ¾ 375 a 0° ¾ 15° 8 January 24, 2003 HT604L/HT614/HT692 20-pin SOP (300mil) Outline Dimensions 1 1 2 0 A B 1 1 0 C C ' G H D E Symbol Rev. 1.10 = F Dimensions in mil Min. Nom. Max. A 394 ¾ 419 B 290 ¾ 300 C 14 ¾ 20 C¢ 490 ¾ 510 D 92 ¾ 104 E ¾ 50 ¾ F 4 ¾ ¾ G 32 ¾ 38 H 4 ¾ 12 a 0° ¾ 10° 9 January 24, 2003 HT604L/HT614/HT692 Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SOP 20W Symbol Description Dimensions in mm A Reel Outer Diameter 330±1.0 B Reel Inner Diameter 62±1.5 C Spindle Hole Diameter 13.0+0.5 -0.2 D Key Slit Width 2.0±0.5 T1 Space Between Flange 24.8+0.3 -0.2 T2 Reel Thickness 30.2±0.2 Rev. 1.10 10 January 24, 2003 HT604L/HT614/HT692 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SOP 20W Symbol Description Dimensions in mm W Carrier Tape Width 24.0+0.3 -0.1 P Cavity Pitch 12.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 11.5±0.1 D Perforation Diameter 1.5+0.1 D1 Cavity Hole Diameter 1.5+0.25 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 10.8±0.1 B0 Cavity Width 13.3±0.1 K0 Cavity Depth 3.2±0.1 t Carrier Tape Thickness 0.3±0.05 C Cover Tape Width Rev. 1.10 21.3 11 January 24, 2003 HT604L/HT614/HT692 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 5/F, Unit A, Productivity Building, Cross of Science M 3rd Road and Gaoxin M 2nd Road, Science Park, Nanshan District, Shenzhen, China 518057 Tel: 0755-8616-9908, 8616-9308 Fax: 0755-8616-9533 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holtek Semiconductor Inc. (Chengdu Sales Office) 709, Building 3, Champagne Plaza, No.97 Dongda Street, Chengdu, Sichuan, China 610016 Tel: 028-6653-6590 Fax: 028-6653-6591 Holmate Semiconductor, Inc. (North America Sales Office) 46729 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright Ó 2003 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.10 12 January 24, 2003