Standard ICs Dual ground sense operational amplifier BA10358 / BA10358F / BA10358FV / BA10358N The BA10358, BA10358F, BA10358FV, and BA10358N are monolithic ICs with two independent built-in operational amplifiers featuring high gain and frequency compensation. These products offer a particularly wide range of operating voltages, from 3 to 32V (when using a single power supply). Current dissipation is low and remains constant regardless of the power supply voltage. Available packages include an 8-pin DIP (BA10358), an 8-pin SOP (BA10358F), an 8-pin SSOP-B (BA10358FV), and an 8-pin SIP (BA10358N). •1)Features Can be driven with a single power supply. 2) Extremely low current dissipation. 3) Level is compatible with any kind of logic circuit. 4) Operating voltage range is 3 to 32V for single power supply, ±1.5 to ±16V for dual power supply. 5) High DC voltage gain. 6) Wide frequency response. 7) Pin assignments is the same as the general-purpose 4558 model. 8) Compatible with model 358 operation amplifiers of other manufacturers. •Absolute maximum ratings Parameter Symbol Limits BA10358 BA10358F BA10358FV BA10358N Unit Power supply voltage VCC 32 (± 16) 32 (± 16) 32 (± 16) 32 (± 16) V Power dissipation Pd 800∗ 550∗ 350∗ 900∗ mW Differential input voltage VID ± VCC ± VCC ± VCC ± VCC V Common-mode input voltage Vl – 0.3 ~ VCC – 0.3 ~ VCC – 0.3 ~ VCC – 0.3 ~ VCC V Operating temperature Topr – 40 ~ +85 – 40 ~ +85 – 40 ~ +85 – 40 ~ +85 °C Storage temperature Tstg – 55 ~ +125 – 55 ~ +125 – 55 ~ +125 – 55 ~ +125 °C ∗ Refer to the Pd characteristic diagram. The values for the BA10358F are those when it is mounted on a glass epoxy board (50mm × 50mm × 1.6mm). The values for the BA10358FV are those when it is mounted on a glass epoxy board (70mm × 70mm × 1.6mm). 1 Standard ICs BA10358 / BA10358F / BA10358FV / BA10358N •Block diagram BA10358 / BA10358F / BA10358FV BA10358N OUT 1 8 VCC – 1N1 2 7 OUT2 6 – 1N2 5 + IN2 + + – 2ch – 1ch 1ch – + 2 3 4 5 6 7 8 + IN1 VEE + IN2 – IN2 OUT2 VCC 4 – – IN1 VEE + 1 3 OUT1 2ch + IN1 •Internal circuit configuration (diagram shows only one channel) VCC – IN OUT + IN VEE 2 Standard ICs BA10358 / BA10358F / BA10358FV / BA10358N •Electrical characteristics (unless otherwise noted, Ta = 25°C, V Parameter CC = +5 V) Symbol Min. Typ. Max. Unit Input offset voltage VIO — 2 7 mV Conditions Input offset current IIO — 5 50 nA — Input bias current IB — 45 250 nA — High-amplitude voltage gain AV 25 100 — V / mV Common-mode input voltage VICM 0 — VCC – 1.5 V Output voltage VO 0 — VCC – 1.5 V RS = 50Ω RL ⭌ 2kΩ, VCC = 15V — RL = 2kΩ Common-mode rejection ratio CMRR 65 80 — dB Power supply voltage rejection ratio PSRR 65 100 — dB RS = 50Ω Quiescent current IQ — 0.7 1.2 mA RL = ∞, on All Op - Amps Channel separation CS — 120 — dB f = 1 kHz input conversion Isource 10 20 — mA VIN + = 1V, VIN – = 0V, VO = 0V Isink 10 20 — mA VIN – = 1V, VIN+ = 0V, VO = VCC source sink •Electrical characteristic curves 1200 140 3 OPEN LOOP VOLTAGE GAIN: Av (dB) Maximum output current — 1000 A SUPPLY CURRENT: IQ (mA) BA10358N 800 BA10358 600 BA10358F 400 BA10358FV – 2 + 1 200 0 0 10M 120 0.1µ VIN 100 – VCC 2 + V0 80 60 40 20 0 25 50 75 85 100 125 150 0 10 20 30 1 40 + Fig. 1 Power dissipation vs. ambient temperature Fig. 2 Quiescent current vs. power supply voltage 20 10 100 1k 10k 100k 1M 10M FREQUENCY: f (Hz) POWER SUPPLY VOLTAGE: V (V) AMBIENT TEMPERATURE: Ta (°C) Fig. 3 Open loop voltage gain vs. frequency 100 100 100k 1k 15V – + 7V VIN 15 INPUT BIAS CURRENT: IR (nA) MAXIMUM OUTPUT VOLTAGE: VOM (V) IQ Vo 2k 10 0 100 1k 10k 100k FREQUENCY: f (Hz) Fig. 4 Maximum output voltage vs.frequency 1M INPUT BIAS CURRENT: I a (nA) POWER DISSIPATION: Pd (mW) VCC 80 60 40 20 0 – 20 0 20 40 60 80 AMBIENT TEMPERATURE: Ta (°C) Fig. 5 Input bias current vs. ambient temperature 75 50 25 0 0 10 20 30 40 + POWER SUPPLY VOLTAGE: V (V) Fig. 6 Input bias current vs. power supply voltage 3 BA10358 / BA10358F / BA10358FV / BA10358N 3 2 1 0 0.001 0.01 0.1 1.0 10 100 OUTPUT SOURCE CURRENT (mA) Fig. 7 Voltage difference during power supply output vs. output source current 1.0 4 RL ⭌ 2kΩ VCC = 15V 3 2 1 0.1 0.01 0.001 0.01 0.1 1.0 10 100 1000 INPUT VOLTAGE VIN (V) 4 OUTPUT VOLTAGE VOUT (V) 10 5 OUTPUT VOLTAGE: VO (V) OUTPUT VOLTAGE REFERENCED TO V+: ∆V (V) Standard ICs 0 3 2 1 0 0 20 OUTPUT SINK CURRENT: IO (mA) Fig. 8 Output voltage vs. output sink current VCC – + To potential in VICM VEE Fig. 10 Handling unused circuits 4 60 80 Fig. 9 Output response characteristics • Operation notes (1) Handling unused circuits If there are any circuits which are not being used, we recommend making connections as shown in Figure 10, with the non-inverted input pin connected to the potential within the in-phase input voltage range (VICM). 40 TIME (µs) Standard ICs BA10358 / BA10358F / BA10358FV / BA10358N •External dimensions (Units: mm) BA10358 BA10358F 5.0 ± 0.2 8 5 1 4 0.11 1.5 ± 0.1 7.62 0.3 ± 0.1 0.15 ± 0.1 4.4 ± 0.2 4 6.2 ± 0.3 1 6.5 ± 0.3 5 0.51Min. 3.2 ± 0.2 3.4 ± 0.3 9.3 ± 0.3 8 0.4 ± 0.1 1.27 0.3Min. 0.5 ± 0.1 0° ~ 15° 2.54 0.15 DIP8 SOP8 BA10358FV BA10358N (0.52) 0.15 ± 0.1 0.65 0.22 ± 0.1 2.8 ± 0.2 1.2 4 5.8 ± 0.2 1 19.3 ± 0.2 10.5 ± 0.5 5 8 1 3.5 ± 0.5 8 4.4 ± 0.2 0.1 1.15 ± 0.1 6.4 ± 0.3 3.0 ± 0.2 2.54 0.6 0.3 ± 0.1 0.8 0.3Min. 1.3 0.1 SSOP-B8 SIP8 5