EPCOS B41858C4687M001 Aluminum electrolytic capacitor Datasheet

Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type:
B41858
Date:
November 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Single-ended capacitors
B41858
Low impedance 105 °C
Long-life grade capacitors
for professional applications
Applications
For use in output circuits of switch-mode power supplies of
compact design
For professional industrial electronics, telecommunications
and data processing equipment
Automotive electronics
Features
Low impedance at high frequency
Low ESR
High ripple current capability
High reliability and long useful life
RoHS-compatible
Construction
Radial leads
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut
Kinked
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details and ordering
example.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 33
B41858
Low impedance 105 °C
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
10 ... 100 V DC
1.15 VR
Rated capacitance CR
Capacitance tolerance
22 ... 10000 µF
±20% M
Dissipation factor tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR (V DC)
10
16
25
35
50
63
100
tan δ (max.)
0.19
Diameter (mm)
8 ... 12.5
16
18
ESL (nH)
20
26
34
0.16
0.14
0.12
0.10
0.10
0.08
Leakage current Ileak
(20 °C, 5 min)
Self-inductance ESL
Useful life
105 °C; VR; IAC,R
105 °C; VR; IAC,R
Requirements
Voltage endurance test
105 °C; VR
Post test requirements
Vibration resistance test
> 3000 h for d = 8 mm
> 5000 h for d ≥ 10 mm
∆C/C
tan δ
Ileak
≤ ±40% of initial value
≤ 3 times initial specified limit
≤ initial specified limit
3000 h for d = 8 mm
5000 h for d ≥ 10 mm
∆C/C ≤ ±30% of initial value
tan δ ≤ 2 times initial specified limit
Ileak
≤ initial specified limit
To IEC 60068-2-6, test Fc:
Displacement amplitude 1.5 mm, frequency range 10 ... 2000 Hz,
acceleration max. 20 g, duration 3 × 2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category
To IEC 60068-1:
55/105/56 (55 °C/+105 °C/56 days damp heat test)
Sectional specification
IEC 60384-4, AEC Q200
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 33
B41858
Low impedance 105 °C
Dimensional drawings
With stand-off rubber seal
Diameters (mm): 10, 12.5, 16, 18
With flat rubber seal
Diameter (mm): 8
Dimensions and weights
Dimensions (mm)
d +0.5
8
10
10
10
12.5
12.5
12.5
12.5
16
16
16
18
18
18
18
18
l
11.5 +1.5
12.5 +1.0
16 +1.0
20 +2.0
20 +2.0
25 +2.0
30 +2.0
40 +2.0
20 +2.0
25 +2.0
31.5 +2.0
20 +2.0
25 +2.0
31.5 +2.0
35 +2.0
40 +2.0
Please read Cautions and warnings and
Important notes at the end of this document.
a ±0.5
3.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
Page 4 of 33
b
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
Approx. weight
g
1.0
1.6
1.9
2.6
3.6
4.5
5.3
7.4
5.5
7.5
7.8
8.0
9.0
11.0
13.0
16.0
B41858
Low impedance 105 °C
Overview of available types
VR (V DC)
10
16
25
35
Case dimensions d × l (mm)
CR (µF)
120
8
× 11.5
150
8
× 11.5
180
8
× 11.5
10
× 12.5
220
8
× 11.5
10
× 12.5
270
8
× 11.5
10
× 12.5
8
× 11.5
10
× 12.5
10
× 16
330
8
× 11.5
390
8
× 11.5
470
8
× 11.5
10
× 12.5
10
× 16
10
× 20
560
10
× 12.5
10
× 16
10
× 16
10
× 20
680
10
× 12.5
10
× 16
12.5 × 20
820
10
× 16
10
× 20
10
1000
10
× 16
10
× 20
12.5 × 20
1200
10
× 16
10
× 20
1500
10
× 20
12.5 × 20
12.5 × 25
1800
10
× 20
12.5 × 25
16
× 20
16
18
× 25
× 20
2200
12.5 × 20
12.5 × 25
12.5 × 40
16 × 25
18 × 20
18
× 25
2700
12.5 × 25
16
× 20
16
18
× 31.5
× 20
18
× 31.5
3300
12.5 × 25
16 × 20
12.5 × 40
16 × 25
18
× 25
18
× 31.5
3900
12.5 × 40
16 × 20
16
18
× 31.5
× 20
18
× 31.5
18
× 35
4700
18
× 20
18
× 25
18
× 31.5
18
× 40
5600
12.5 × 40
18
× 35
6800
16
× 31.5
18
× 31.5
18
× 40
8200
18
× 31.5
18
× 35
10000
18
× 35
18
× 40
Please read Cautions and warnings and
Important notes at the end of this document.
× 20
12.5 × 25
16 × 20
16
Page 5 of 33
× 20
12.5 × 40
16 × 25
B41858
Low impedance 105 °C
VR (V DC)
50
63
100
Case dimensions d × l (mm)
CR (µF)
22
8
× 11.5
27
10
× 12.5
33
10
× 16
56
10
× 20
68
82
8
× 11.5
10
× 12.5
100
8
× 11.5
10
× 12.5
12.5 × 20
120
10
× 12.5
10
× 16
12.5 × 25
150
10
× 12.5
10
× 16
180
10
× 16
10
× 20
12.5 × 30
16 × 20
220
10
× 16
10
× 20
16
270
330
10
× 20
390
12.5 × 40
18 × 20
12.5 × 20
18
× 25
12.5 × 25
18
× 31.5
12.5 × 25
16 × 20
18
× 35
18
× 35
18
× 40
470
12.5 × 20
560
12.5 × 25
680
12.5 × 30
12.5 × 40
16 × 25
18 × 20
820
12.5 × 40
16 × 20
16
18
× 31.5
× 25
1000
16
18
× 31.5
× 20
16
× 31.5
1200
18
× 20
18
× 31.5
1500
18
× 25
18
× 35
1800
18
× 31.5
18
× 40
2200
18
× 35
2700
18
× 40
Other voltage and capacitance ratings are available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
× 25
12.5 × 20
Page 6 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 10 V DC
330
8 × 11.5
390
8 × 11.5
470
8 × 11.5
560 10 × 12.5
680 10 × 12.5
820 10 × 16
1000 10 × 16
1200 10 × 16
1500 10 × 20
1800 10 × 20
2200 12.5 × 20
2700 12.5 × 25
3300 12.5 × 25
3300 16 × 20
3900 12.5 × 40
3900 16 × 20
4700 18 × 20
5600 12.5 × 40
6800 16 × 31.5
8200 18 × 31.5
10000 18 × 35
2.195
2.195
2.195
1.035
1.035
0.946
0.946
0.944
0.584
0.584
0.496
0.327
0.327
0.307
0.240
0.307
0.271
0.243
0.192
0.165
0.160
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
0.727
0.615
0.511
0.429
0.353
0.293
0.240
0.199
0.159
0.133
0.121
0.098
0.088
0.088
0.074
0.074
0.067
0.061
0.054
0.051
0.047
0.274
0.274
0.274
0.129
0.129
0.118
0.118
0.118
0.073
0.073
0.062
0.041
0.041
0.038
0.030
0.038
0.034
0.030
0.024
0.021
0.020
0.246
0.246
0.246
0.113
0.113
0.105
0.105
0.105
0.062
0.062
0.060
0.034
0.034
0.033
0.025
0.033
0.031
0.025
0.022
0.020
0.018
436
436
436
746
746
846
846
846
1202
1202
1396
2028
2028
2146
2858
2146
2381
2858
3122
3539
3864
654
654
654
1118
1118
1269
1269
1269
1803
1803
2094
3043
3043
3219
4287
3219
3571
4286
4683
5308
5796
B41858C3337M***
B41858C3397M***
B41858C3477M***
B41858C3567M***
B41858C3687M***
B41858C3827M***
B41858C3108M***
B41858C3128M***
B41858C3158M***
B41858C3188M***
B41858C3228M***
B41858C3278M***
B41858C3338M***
B41858D3338M***
B41858C3398M***
B41858D3398M***
B41858C3478M***
B41858C3568M***
B41858C3688M***
B41858C3828M***
B41858C3109M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 16 V DC
270
8 × 11.5
330
8 × 11.5
470 10 × 12.5
560 10 × 16
680 10 × 16
820 10 × 20
1000 10 × 20
1200 10 × 20
1500 12.5 × 20
1800 12.5 × 25
2200 12.5 × 25
2700 16 × 20
3300 12.5 × 40
3300 16 × 25
3900 16 × 31.5
3900 18 × 20
4700 18 × 25
6800 18 × 31.5
8200 18 × 35
10000 18 × 40
2.192
2.192
1.035
0.944
0.946
0.584
0.584
0.584
0.496
0.327
0.327
0.307
0.243
0.251
0.192
0.271
0.217
0.165
0.160
0.125
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
0.748
0.612
0.430
0.360
0.297
0.243
0.202
0.168
0.135
0.112
0.103
0.084
0.077
0.077
0.065
0.065
0.059
0.048
0.046
0.043
0.274
0.274
0.129
0.118
0.118
0.073
0.073
0.073
0.062
0.041
0.041
0.038
0.030
0.031
0.024
0.034
0.027
0.021
0.020
0.016
0.246
0.246
0.113
0.105
0.105
0.062
0.062
0.062
0.060
0.034
0.034
0.033
0.025
0.029
0.022
0.031
0.024
0.020
0.018
0.015
436
436
746
846
846
1202
1202
1202
1396
2028
2028
2146
2858
2483
3122
2381
2941
3539
3864
4467
654
654
1118
1269
1269
1803
1803
1803
2094
3043
3043
3219
4286
3724
4683
3571
4412
5308
5796
6700
B41858D4277M***
B41858D4337M***
B41858C4477M***
B41858C4567M***
B41858C4687M***
B41858C4827M***
B41858C4108M***
B41858C4128M***
B41858C4158M***
B41858C4188M***
B41858C4228M***
B41858C4278M***
B41858D4338M***
B41858C4338M***
B41858D4398M***
B41858C4398M***
B41858C4478M***
B41858C4688M***
B41858C4828M***
B41858C4109M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 25 V DC
180
8 × 11.5
220
8 × 11.5
270 10 × 12.5
330 10 × 12.5
470 10 × 16
560 10 × 16
680 10 × 20
820 10 × 20
1000 12.5 × 20
1500 12.5 × 25
1800 16 × 20
2200 12.5 × 40
2200 16 × 25
2200 18 × 20
2700 16 × 31.5
2700 18 × 20
3300 18 × 25
3900 18 × 31.5
4700 18 × 31.5
5600 18 × 35
6800 18 × 40
2.192
2.192
1.032
1.035
0.946
0.944
0.584
0.584
0.496
0.327
0.307
0.243
0.251
0.248
0.192
0.271
0.217
0.165
0.168
0.160
0.128
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
0.982
0.803
0.654
0.536
0.376
0.315
0.260
0.216
0.177
0.118
0.098
0.092
0.092
0.091
0.075
0.075
0.069
0.058
0.053
0.049
0.044
0.274
0.274
0.129
0.129
0.118
0.118
0.073
0.073
0.062
0.041
0.038
0.030
0.031
0.031
0.024
0.034
0.027
0.021
0.021
0.020
0.016
0.246
0.246
0.113
0.113
0.105
0.105
0.062
0.062
0.060
0.034
0.033
0.025
0.029
0.031
0.022
0.031
0.024
0.020
0.020
0.018
0.015
436
436
746
746
846
846
1202
1202
1396
2028
2146
2858
2483
2381
3122
2381
2941
3539
3539
3864
4467
654
654
1119
1118
1269
1269
1803
1803
2094
3043
3219
4286
3724
3572
4683
3571
4412
5308
5309
5796
6701
B41858D5187M***
B41858D5227M***
B41858C5277M***
B41858C5337M***
B41858C5477M***
B41858C5567M***
B41858C5687M***
B41858C5827M***
B41858C5108M***
B41858C5158M***
B41858C5188M***
B41858D5228M***
B41858C5228M***
B41858E5228M***
B41858D5278M***
B41858C5278M***
B41858C5338M***
B41858C5398M***
B41858D5478M***
B41858D5568M***
B41858C5688M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 35 V DC
120
8 × 11.5
150
8 × 11.5
180 10 × 12.5
220 10 × 12.5
330 10 × 16
470 10 × 20
560 10 × 20
680 12.5 × 20
1000 12.5 × 25
1000 16 × 20
1200 16 × 20
1500 12.5 × 40
1500 16 × 25
1800 16 × 25
1800 18 × 20
2200 18 × 25
2700 18 × 31.5
3300 18 × 31.5
3900 18 × 35
4700 18 × 40
2.192
2.192
1.035
1.035
0.946
0.584
0.584
0.496
0.327
0.304
0.307
0.243
0.251
0.248
0.271
0.217
0.165
0.168
0.160
0.125
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
1.263
1.010
0.842
0.689
0.459
0.323
0.271
0.223
0.152
0.151
0.126
0.101
0.101
0.084
0.084
0.080
0.065
0.061
0.051
0.048
0.274
0.274
0.129
0.129
0.118
0.073
0.073
0.062
0.041
0.038
0.038
0.030
0.031
0.031
0.034
0.027
0.021
0.021
0.020
0.016
0.246
0.246
0.113
0.113
0.105
0.062
0.062
0.060
0.034
0.033
0.033
0.025
0.029
0.029
0.031
0.024
0.020
0.020
0.018
0.015
436
436
746
746
846
1202
1202
1396
2028
2146
2146
2858
2483
2483
2381
2941
3539
3539
3864
4467
654
654
1118
1118
1269
1803
1803
2094
3043
3219
3219
4286
3724
3725
3571
4412
5308
5309
5796
6700
B41858D7127M***
B41858C7157M***
B41858C7187M***
B41858C7227M***
B41858C7337M***
B41858C7477M***
B41858C7567M***
B41858C7687M***
B41858C7108M***
B41858D7108M***
B41858C7128M***
B41858D7158M***
B41858C7158M***
B41858E7188M***
B41858C7188M***
B41858C7228M***
B41858C7278M***
B41858D7338M***
B41858C7398M***
B41858C7478M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 50 V DC
82
8 × 11.5
100
8 × 11.5
120 10 × 12.5
150 10 × 12.5
180 10 × 16
220 10 × 16
330 10 × 20
470 12.5 × 20
560 12.5 × 25
680 12.5 × 30
820 12.5 × 40
820 16 × 20
1000 16 × 31.5
1000 18 × 20
1200 18 × 20
1500 18 × 25
1800 18 × 31.5
2200 18 × 35
2700 18 × 40
5.168
5.168
2.984
2.984
1.400
1.400
1.000
0.880
0.712
0.360
0.269
0.401
0.260
0.477
0.384
0.382
0.300
0.268
0.210
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
1.540
1.263
1.053
0.842
0.702
0.574
0.383
0.269
0.226
0.186
0.154
0.154
0.126
0.126
0.105
0.084
0.070
0.069
0.065
0.646
0.646
0.373
0.373
0.175
0.175
0.125
0.110
0.089
0.045
0.034
0.050
0.032
0.048
0.048
0.038
0.030
0.027
0.021
0.573
0.573
0.336
0.336
0.160
0.160
0.118
0.104
0.082
0.043
0.032
0.046
0.030
0.044
0.044
0.036
0.028
0.024
0.020
340
340
555
555
778
778
1030
1300
1490
2140
2799
1820
2653
1997
1997
2417
2989
3320
3871
510
510
833
833
1167
1167
1545
1950
2235
3210
4199
2730
3980
2995
2996
3626
4483
4980
5807
B41858C6826M***
B41858C6107M***
B41858C6127M***
B41858C6157M***
B41858C6187M***
B41858C6227M***
B41858C6337M***
B41858C6477M***
B41858C6567M***
B41858C6687M***
B41858C6827M***
B41858D6827M***
B41858C6108M***
B41858D6108M***
B41858C6128M***
B41858C6158M***
B41858C6188M***
B41858C6228M***
B41858C6278M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
VR = 63 V DC
56
8 × 11.5
68
8 × 11.5
82 10 × 12.5
100 10 × 12.5
120 10 × 16
150 10 × 16
180 10 × 20
220 10 × 20
270 12.5 × 20
330 12.5 × 20
390 12.5 × 25
470 12.5 × 25
470 16 × 20
680 12.5 × 40
680 16 × 25
680 18 × 20
820 16 × 31.5
820 18 × 25
1000 16 × 31.5
1200 18 × 31.5
1500 18 × 35
1800 18 × 40
5.413
4.328
5.766
4.616
3.075
2.464
1.986
1.592
1.688
1.688
1.236
0.992
1.037
0.717
0.772
0.960
0.541
0.761
0.432
0.518
0.441
0.375
ESRmax
120 Hz
20 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
2.256
1.857
1.540
1.263
1.053
0.842
0.702
0.574
0.468
0.383
0.324
0.268
0.269
0.186
0.186
0.186
0.154
0.154
0.126
0.105
0.084
0.070
0.541
0.541
0.577
0.577
0.308
0.308
0.199
0.199
0.169
0.169
0.124
0.124
0.104
0.072
0.077
0.096
0.054
0.076
0.054
0.052
0.044
0.038
0.488
0.488
0.500
0.500
0.279
0.279
0.180
0.180
0.153
0.153
0.112
0.112
0.094
0.065
0.070
0.087
0.049
0.069
0.049
0.047
0.040
0.034
310
310
354
354
519
519
705
705
876
876
1118
1118
1272
1785
1600
1427
2092
1735
2092
2294
2592
2967
464
465
531
531
779
779
1058
1058
1315
1315
1676
1677
1907
2677
2400
2140
3138
2602
3138
3441
3888
4450
B41858C8566M***
B41858C8686M***
B41858C8826M***
B41858C8107M***
B41858C8127M***
B41858C8157M***
B41858C8187M***
B41858C8227M***
B41858C8277M***
B41858C8337M***
B41858C8397M***
B41858E8477M***
B41858C8477M***
B41858C8687M***
B41858D8687M***
B41858E8687M***
B41858C8827M***
B41858D8827M***
B41858C8108M***
B41858C8128M***
B41858C8158M***
B41858C8188M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 33
B41858
Low impedance 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
120 Hz
20 °C
Ω
VR = 100 V DC
22
8 × 11.5 12.219 4.593
27 10 × 12.5 9.813 3.743
33 10 × 16
6.542 3.062
56 10 × 20
4.606 1.804
100 12.5 × 20
3.048 1.011
120 12.5 × 25
2.038 0.842
180 12.5 × 30
1.732 0.561
180 16 × 20
1.313 0.561
220 16 × 25
0.985 0.459
270 12.5 × 40
1.314 0.374
270 18 × 20
1.260 0.374
330 16 × 31.5 0.973 0.306
330 18 × 25
1.008 0.306
390 18 × 31.5 0.720 0.259
470 18 × 35
0.679 0.215
560 18 × 35
0.679 0.180
680 18 × 40
0.438 0.149
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
IAC,max
Ordering code
100 kHz (composition see
85 °C
below)
mA
1.222
0.981
0.654
0.461
0.305
0.204
0.173
0.131
0.099
0.131
0.126
0.097
0.101
0.072
0.068
0.068
0.044
1.114
0.883
0.589
0.423
0.281
0.188
0.159
0.122
0.091
0.121
0.119
0.090
0.095
0.068
0.063
0.063
0.042
205
266
357
460
647
864
1009
1119
1402
1309
1220
1546
1477
1907
2061
2061
2683
307
400
536
691
971
1296
1514
1678
2103
1963
1830
2319
2215
2861
3092
3092
4025
B41858C9226M***
B41858C9276M***
B41858C9336M***
B41858C9566M***
B41858C9107M***
B41858C9127M***
B41858C9187M***
B41858D9187M***
B41858C9227M***
B41858C9277M***
B41858D9277M***
B41858C9337M***
B41858D9337M***
B41858C9397M***
B41858C9477M***
B41858C9567M***
B41858C9687M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d × l = 10 × 20 mm to 18 × 40 mm, excluding 12.5 × 30/40 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm, excluding d × l = 12.5 × 30/40 mm)
003 = for crimped leads, blister (from d × l = 16 × 20 mm to 18 × 40 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm, excluding 12.5 × 30/40 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 33
B41858
Low impedance 105 °C
Useful life
depending on ambient temperature TA under ripple current operating conditions1)
d = 8 mm
d ≥ 10 mm
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 33
B41858
Low impedance 105 °C
Frequency factor of permissible ripple current IAC versus frequency f
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 33
B41858
Low impedance 105 °C
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows:
Lead spacing F = 2.5 mm (∅ d = 5 … 6.3 mm)
Lead spacing F = 3.5 mm (∅ d = 8 mm)
Lead spacing F = 5.0 mm (from d × l = 10 × 12.5 mm to 12.5 × 30 mm)
Lead spacing F = 7.5 mm (∅ d = 16 ... 18 mm).
Lead spacing 2.5 mm (∅ d = 5 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
∅d
5
F
H
W
W0
W1
W2
H0
P
P0
P1
I1
t
∆h
D0
2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
6.3
Toler- +0.8
±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
ance 0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 33
B41858
Low impedance 105 °C
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅d
8
Tolerance
F
H
W
W0
W1
W2
P
P0
P1
I1
t
∆h
3.5
18.5
18.0
12.5
9.0
1.5
12.7
12.7
4.6
1.0
0.7
1.0
+0.8
±1.0
0.2
±0.5
min.
±0.5
max. ±1.0
±0.2
±0.5
max. ±0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 33
D0
4.0
max. ±0.2
B41858
Low impedance 105 °C
Lead spacing 5.0 mm (∅ d = 5 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (from d × l = 10 × 12.5 mm to 12.5 × 30 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
∅d
5
6.3
F
H
W
W0
W1
W2
H0
P
P0
P1
I1
t
∆h
D0
5.0
18.5
18.0 5.5
9.0
1.5
16.0
12.7
12.7
3.85
1.0
0.7
1.0
4.0
16.0
12.7
12.7
3.85
18.0 12.5 9.0
1.5
12.7
12.7
3.85
1.0
0.7
1.0
4.0
15.0
15.0
5.0
±1.0
±0.2
±0.5
8
10
20.0
5.0
19.0
12.5
19.0
Toler- +0.8
±0.75 ±0.5 min. ±0.5 max. ±0.5
ance 0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 33
max. ±0.2 max. ±0.2
B41858
Low impedance 105 °C
Lead spacing 7.5 mm (∅ d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
∅d
16
F
H
W
7.5 18.5 18.0
18 *)
Toler0.5
±0.8
±0.5
ance
+0.75
W0
W1
W2
P
P0
P1
I1
t
∆P
∆h
D0
12.5
9.0
1.5
30.0
15.0
3.75
1.0
0.7
0
0
4.0
min.
±0.5
max. ±1.0
±0.2
±0.5
max. ±0.2 ±1.0 ±1.0 ±0.2
*) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 33
B41858
Low impedance 105 °C
Packing units and box dimensions
Ammo pack
Please read Cautions and warnings and
Important notes at the end of this document.
Case size
d×l
mm
Dimensions (mm)
Amax
Bmax
Cmax
5 × 11
345
55
240
2000
6.3 × 11
345
55
290
2000
8 × 11.5
345
55
240
1000
10 × 12.5
345
55
280
750
10 × 16
345
60
200
500
10 × 20
345
60
200
500
12.5 × 20
345
65
280
500
12.5 × 25
345
65
280
500
16 × 20
315
65
275
300
16 × 25
315
65
275
300
16 × 31.5
315
65
275
300
18 × 20
315
65
275
250
18 × 25
315
65
275
250
18 × 31.5
315
65
275
250
Page 20 of 33
Packing
units
pcs.
B41858
Low impedance 105 °C
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also
available upon request.
Kinked leads
Last 3 digits of ordering code: 001
With stand-off rubber seal
Case size
d × l (mm)
With flat rubber seal
Please read Cautions and warnings and
Important notes at the end of this document.
Page 21 of 33
Dimensions (mm)
a ±0.5
10 × 20
5.0
12.5 × 20
5.0
12.5 × 25
5.0
16 × 20
7.5
16 × 25
7.5
16 × 31.5
7.5
18 × 20
7.5
18 × 25
7.5
18 × 31.5
7.5
18 × 35
7.5
18 × 40
7.5
B41858
Low impedance 105 °C
Cut leads
Last 3 digits of ordering code: 002
With stand-off rubber seal
Case size
d × l (mm)
With flat rubber seal
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 33
Dimensions (mm)
a ±0.5
10 × 12.5
5.0
10 × 16
5.0
10 × 20
5.0
12.5 × 20
5.0
12.5 × 25
5.0
16 × 20
7.5
16 × 25
7.5
16 × 31.5
7.5
18 × 20
7.5
18 × 25
7.5
18 × 31.5
7.5
18 × 35
7.5
18 × 40
7.5
20 × 20
10.0
20 × 25
10.0
20 × 30
10.0
20 × 35
10.0
20 × 40
10.0
22 × 30
10.0
22 × 35
10.0
22 × 40
10.0
B41858
Low impedance 105 °C
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 20 mm.
There are three configurations available: Crimped leads, J leads, bent 90° leads
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal
With flat rubber seal
Suggestion for PCB hole diameter
Case size
d × l (mm)
Dimensions (mm)
B ±0.2
C ±0.5
D ±0.1
E ±0.1
16 × 20
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
16 × 25
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
16 × 31.5
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
18 × 20
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 25
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 31.5
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 35
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 40
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
20 × 20
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 25
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 30
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 35
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 40
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 33
a ±0.5
∅b
B41858
Low impedance 105 °C
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size
d × l (mm)
Dimensions (mm)
C ±0.5
E ±0.5
J ±0.2
10 × 12.5
3.2
0.7
1.2
5.0
0.6 ±0.05
10 × 16
3.2
0.7
1.2
5.0
0.6 ±0.05
10 × 20
3.2
0.7
1.2
5.0
0.6 ±0.05
12.5 × 20
3.2
0.7
1.2
5.0
0.6 ±0.05
12.5 × 25
3.2
0.7
1.2
5.0
0.6 ±0.05
16 × 20
3.5
0.7
1.6
7.5
0.8 ±0.05
16 × 25
3.5
0.7
1.6
7.5
0.8 ±0.05
16 × 31.5
3.5
0.7
1.6
7.5
0.8 ±0.05
18 × 20
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 25
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 31.5
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 35
3.5
0.7
1.6
7.5
0.8 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 33
a ±0.5
∅b
B41858
Low impedance 105 °C
Bent 90° leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size
d × l (mm)
Dimensions (mm)
C ±0.5
E ±0.5
F ±0.5
a ±0.5
∅b
16 × 20
4.0
4.0
12.0
7.5
0.8 ±0.05
16 × 25
4.0
4.0
12.0
7.5
0.8 ±0.05
16 × 31.5
4.0
4.0
12.0
7.5
0.8 ±0.05
18 × 20
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 25
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 31.5
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 35
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 40
4.0
4.0
13.0
7.5
0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 33
B41858
Low impedance 105 °C
Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5
PAPR
Case size
d×l
Taped,
Ammo pack
mm
Standard,
bulk
pcs.
pcs.
Kinked
leads,
bulk
pcs.
Cut
leads,
bulk
pcs.
Crimped J leads,
leads,
blister
blister
pcs.
pcs.
2000
5 × 11
2000
6.3 × 11
2500
2000
8 × 11.5
1000
1000
10 × 12.5
1000
750
10 × 16
1000
500
1000
10 × 20
500
500
500
500
12.5 × 20
350
500
350
350
12.5 × 25
250
500
500
500
12.5 × 30
200
12.5 × 35
175
12.5 × 40
175
16 × 20
250
300
200
200
200
200
120
16 × 25
250
300
200
200
200
200
120
16 × 31.5
200
300
250
250
344
344
120
The last three
digits of the
complete
ordering code
state the lead
configuration
000
Code
006
007
008
009
001
002
003
004
012
F (mm) d (mm)
3.5
2.5
5
7.5
8
5...6.3
5...12.5
16...18
1) Available upon request
Please read Cautions and warnings and
Important notes at the end of this document.
Page 26 of 33
1000
Bent 90°
leads,
blister
pcs.
675
675
500
300
1)
225
1)
B41858
Low impedance 105 °C
Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40
PAPR
Case size
d×l
Taped,
Ammo pack
mm
Standard,
bulk
pcs.
pcs.
Kinked
leads,
bulk
pcs.
Cut
leads,
bulk
pcs.
Crimped J leads,
leads,
blister
blister
pcs.
pcs.
Bent 90°
leads,
blister
pcs.
18 × 20
175
18 × 25
150
250
175
175
200
200
120
250
150
150
200
200
18 × 31.5
120
100
250
100
100
150
150
120
18 × 35
100
100
100
150
150
150
18 × 40
125
100
100
120
72
20 × 20
125
125
200
20 × 25
125
125
200
20 × 30
100
100
120
20 × 35
100
100
120
20 × 40
100
100
120
22 × 30
80
100
22 × 35
80
22 × 40
80
25 × 40
40
The last three
digits of the
complete
ordering code
state the lead
configuration
000
Code
007
008
009
Please read Cautions and warnings and
Important notes at the end of this document.
F (mm) d (mm)
2.5
5
7.5
100
100
001
002
4...6.3
6.3...12.5
16...18
Page 27 of 33
003
004
012
B41858
Low impedance 105 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 33
B41858
Low impedance 105 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 29 of 33
B41858
Low impedance 105 °C
Topic
Soldering,
cleaning agents
Passive
flammability
Active
flammability
Safety information
Reference
Chapter "General
technical information"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Avoid external energy, such as fire or electricity.
8.1
"Passive flammability"
Avoid overload of the capacitors.
8.2
"Active flammability"
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Please read Cautions and warnings and
Important notes at the end of this document.
Page 30 of 33
Reference
Chapter "Capacitors
with screw terminals"
"Screw terminals accessories"
B41858
Low impedance 105 °C
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Rated ripple current for base cooling
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,rms
IAC,f
IAC,max
IAC,R
IAC,R (B)
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
∆T
TA
TC
TB
t
∆t
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Nennwechselstromstrom für Bodenkühlung
Ableitstrom
Ableitstrom bei Betrieb
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Becherbodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 31 of 33
B41858
Low impedance 105 °C
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Notes
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 32 of 33
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
Page 33 of 33
Similar pages