HPL21PT CHENMKO ENTERPRISE CO.,LTD THRU SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 2.0 Amperes HPL28PT PROVISIONAL SPEC. FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals SMP 0.081 (2.05) 0.077 (1.95) 0.170 (4.31) 0.163 (4.15) (3) (1) (2) 0.019 (0.50 Min.) 0.077 (1.95) 0.073 (1.85) 0.045 (1.16) 0.042 (1.07) 0.005 (0.15 Min.) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) CIRCUIT 2 0.212 (5.38) 0.208 (5.29) 1 0.055 (1.40) 0.051 (1.30) SMP Dimensions in inches and (millimeters) 3 MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS SYMBOL HPL21PT HPL22PT HPL23PT HPL24PT HPL25PT HPL26PT HPL27PT HPL28PT UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 1000 Volts o Maximum Average Forward Rectified Current TL = 100 C IO 2.0 Amps IFSM 60 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ 30 TJ, TSTG 20 pF o -65 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 2.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC Maximum Full Load Reverse Current Average, Full Cycle at TA = 55oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A VF HPL21PT HPL22PT HPL23PT HPL24PT HPL25PT HPL26PT HPL27PT HPL28PT 1.0 1.3 1.5 1.7 UNITS Volts 5.0 uAmps 100 uAmps IR trr 50 70 nSec 2004-7 FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) D.U.T (+) 0 PULSE GENERATOR (NOTE 2) 25 Vdc (approx) (-) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A 1cm NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. SET TIME BASE FOR 10/20 nS/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 2.0 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) TJ =100oC 1.0 TJ =25oC .1 L2 6P T 8P T 5PT HP T~ 7P L2 HP PT L24 HP L2 PL2 ~H ~H PT L21 HP PL2 Pulse Width = 300uS 1% Duty Cycle 1.0 HP TJ =125oC 10 3PT 10 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 0.1 TJ =25oC .01 .001 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1.8 FIG. 6 - TYPICAL JUNCTION CAPACITANCE 70 200 60 JUNCTION CAPACITANCE, ( pF ) PEAK FORWARD SURGE CURRENT, ( A ) AVERAGE FORWARD CURRENT, ( A ) RATING CHARACTERISTIC CURVES ( HPL21PT THRU HPL28PT ) 8.3ms Single Half Sine-Wave (JEDEC Method) 50 40 30 20 10 0 100 60 HPL2 1PT~ 40 HPL26 20 HPL2 5PT PT~HPL 28PT 10 6 4 TJ =25oC 2 1 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100