ETC AH118-89PCB2140 1/4 watt, high linearity ingap hbt amplifier Datasheet

AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Features
Product Description
• 60 – 2500 MHz
• +24.7 dBm P1dB
• +40.5 dBm Output IP3
• 20.4 dB Gain @ 900 MHz
• 16.5 dB Gain @ 1900 MHz
• +5V Single Positive Supply
• SOT-89 SMT Package
Applications
•
•
•
•
Final stage amplifiers for Repeaters
Mobile Infrastructure
CATV / DBS
Defense / Homeland Security
Functional Diagram
The AH118 is a high dynamic range driver amplifier in a
low-cost surface mount package. The InGaP/GaAs HBT
is able to achieve high performance across a broad range
with +40.5 dBm OIP3 and +24.7 dBm of compressed
1dB power. It is housed in an industry standard SOT-89
SMT package. All devices are 100% RF and DC tested.
4
2
1
The AH118 is targeted for use as a driver amplifier in
wireless infrastructure where high linearity and medium
power is required. Internal biasing allows the AH118 to
maintain high linearity over temperature and operate
directly off a single +5V supply. This combination
makes the device an excellent candidate for transceiver
line cards in current and next generation multi-carrier 3G
base stations.
Specifications
Parameter
Product Information
3
Function
Input / Base
Output / Collector
Ground
Pin No.
1
3
2, 4
Typical Performance
Units
Frequency
S21 - Gain
S11 - Input R.L.
S22 - Output R.L.
Output P1dB
Output IP3
IS-95A Channel Power
@ -45 dBc ACPR
W-CDMA Channel Power
@ -45 dBc ACLR, 2140 MHz
Noise Figure
Operating Current Range
Device Voltage
MHz
dB
dB
dB
dBm
dBm
Min
Typ
Max
+18
dBm
+16.7
W-CDMA Channel Power
dB
mA
V
140
4.3
160
+5
Absolute Maximum Rating
Operating Case Temperature
Storage Temperature
RF Input Power (continuous)
Device Voltage
Device Current
Units
dBm
+23
+39.5
@ -45 dBc ACPR,
@ -45 dBc ACLR
175
Test conditions unless otherwise noted.
1. T = 25ºC, Vsupply = +5 V, Frequency = 1900 MHz, in tuned application circuit.
2. 3OIP measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Parameter
Parameter
Frequency
S21 - Gain
S11 - Input R.L.
S22 - Output R.L.
Output P1dB
Output IP3
IS-95A Channel Power
13.5
1900
16.5
-12
-18
+24.7
+40.5
Rating
-40 to +85 °C
-65 to +150 °C
+15 dBm
+6 V
220 mA
Noise Figure
Supply Bias
Typical
MHz
dB
dB
dB
dBm
dBm
900
20.4
-15
-12
+24.2
+40
1900
16.5
-12
-18
+24.7
+40.5
dBm
+18.2
+18
dBm
dB
2140
16.3
-15
-16
+24.7
+40.5
+16.7
4.0
4.3
4.8
+5 V @ 160 mA
Typical parameters reflect performance in a tuned application circuit:
Supply Voltage = +5 V, I = 160 mA, +25° C
Ordering Information
Part No.
Description
AH118-89
AH118-89PCB900
AH118-89PCB1900
AH118-89PCB2140
¼ Watt, High Linearity InGaP HBT Amplifier
900 MHz Evaluation Board
1900 MHz Evaluation Board
2140 MHz Evaluation Board
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Information
Typical Device Data
S-Parameters (VDevice = +5 V, ICC = 160 mA, 25° C, unmatched 50 ohm system)
S11
0.
4
30
0.8
0
3.
2.
0
0
3.
0
4.
25
0
4.
5.0
0. 2
20
5.0
0. 2
10.0
5.0
4.0
3.0
2.0
1.0
0.8
0.6
0.4
0.2
10.0
0
10.0
5.0
4.0
3.0
2.0
1.0
0.8
0.6
0
0.2
15
0.4
10.0
10
5
-10.0
2
-0 .
-5.
0
2
-0 .
-5.
0
0
-10.0
-4
.0
-3
.0
.0
-2
.4
-0
-0.8
Swp Min
0.01GHz
Swp Min
0.01GHz
-1.0
2.5
-0
.6
2
-0.8
1
1.5
Frequency (GHz)
-1.0
0.5
-0
.6
0
.0
-2
.4
-0
-10
-3
.0
-5
-4
.0
Gain (dB)
Swp Max
6GHz
6
0.
2.
0
DB(GMax)
1.0
1.0
0.8
6
0.
DB(|S[2,1]|)
35
S22
Swp Max
6GHz
0.
4
Gain / Maximum Stable Gain
40
Notes:
The gain for the unmatched device in 50 ohm system is shown as the trace in black color. For a tuned circuit for a particular frequency,
it is expected that actual gain will be higher, up to the maximum stable gain. The maximum stable gain is shown in the dashed red line.
The impedance plots are shown from 50 – 6000 MHz, with markers placed at 0.5 – 6.0 GHz in 0.5 GHz increments.
S-Parameters (VDevice = +5 V, ICC = 160 mA, 25°C, unmatched 50 ohm system, calibrated to device leads)
Freq (MHz)
50
100
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
-2.69
-2.16
-1.91
-1.77
-1.60
-1.45
-1.40
-1.25
-1.20
-1.17
-1.13
-1.11
-1.05
-0.99
-0.93
-0.95
-0.92
-173.38
-177.19
178.30
172.47
166.83
161.09
155.39
149.59
143.79
137.57
132.05
126.72
121.50
115.58
110.41
105.30
100.11
21.74
19.63
18.22
17.13
15.99
14.97
13.84
12.76
11.71
10.63
9.75
8.88
8.00
7.31
6.52
5.73
5.05
153.70
150.82
148.19
135.41
121.91
109.02
97.28
86.83
76.95
68.15
59.55
52.22
45.09
37.40
30.66
23.51
17.07
-31.02
-30.31
-29.87
-29.83
-29.49
-29.18
-28.70
-28.63
-28.30
-27.94
-27.63
-27.51
-27.06
-27.02
-26.78
-26.66
-26.61
11.24
7.90
5.01
4.07
2.79
2.11
1.64
-0.09
-1.34
-4.47
-7.00
-8.43
-11.00
-14.19
-18.24
-20.10
-23.28
-7.02
-5.57
-5.06
-4.77
-4.60
-4.44
-4.26
-4.14
-3.97
-4.00
-3.86
-3.84
-3.62
-3.55
-3.46
-3.34
-3.30
-148.17
-162.45
-173.51
177.87
171.65
166.08
160.40
155.01
149.63
144.03
139.02
134.24
129.30
124.42
119.42
114.26
109.29
Application Circuit PC Board Layout
Circuit Board Material: .062” total thickness with a .014” Getek top RF layer, 4 layers (other layers added for rigidity),
1 oz copper, Microstrip line details: width = .026”, spacing = .026”
The silk screen markers ‘A’, ‘B’, ‘C’, etc. and ‘1’, ‘2’, ‘3’, etc. are used as placemarkers for the input and output tuning.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Information
900 MHz Application Circuit (AH118-89PCB900)
Vcc = +5 V
Typical RF Performance at 25°C
Frequency
S21 – Gain
S11 – Input Return Loss
S22 – Output Return Loss
Output P1dB
Output IP3
(+17 dBm / tone, 1 MHz spacing)
Channel Power
(@-45 dBc ACPR, IS-95 9 channels fwd)
Noise Figure
Device / Supply Voltage
Quiescent Current
900 MHz
20.4 dB
-15 dB
-12 dB
+24.2 dB
+40 dB
CAP
ID=C1
C=1e5 pF
size 1206
All passive components are of size 0603 unless otherwise noted.
CAP
ID=C2
C=1000 pF
The diode D1 is used as over-voltage protection on the evaluation
boards. It is not specifically required in the final circuit layout in
a system using a DC regulator.
DIODE1
ID=D1
5.6 V
Component R1 is shown in the silkscreen but is not used for this
configuration.
L2 - the 0 ohm resistor - can be removed (with a thru line) in the
final circuit layout.
PORT
P=1
Z=50 Ohm
CAP
ID=C4
C=100 pF
CAP
ID=C3
C=56 pF
size 0805
IND
ID=L1
L=33 nH
size 0805
RES
ID=L2
R=0 Ohm
CAP
ID=C5
C=100 pF
PORT
P=2
Z=50 Ohm
+18.2 dB
4 dB
+5 V
160 mA
IND
ID=L3
L=2.7 nH
SUBCKT
ID=U1
NET="AH118"
CAP
ID=C7
C=8.2 pF
CAP
ID=C9
C=2 pF
C7 should be placed at the silk screen
marker 'C' on the WJ evaluation board.
The capacitor should be placed
19.5° @ 0.9GHz from pin 3
of the AH118.
The capacitor should be placed
6.1° @ 0.9GHz from pin 1 of the AH118
Gain
Return Loss
22
0
21
-5
20
-10
19
-15
18
-20
C9 should be placed between
silk screen markers '8' and '9'
on the WJ evaluation board.
ACPR vs. Channel Power
S11
-40
S22
IS-95, 9 Ch. Fwd, ±885 kHz offset, 30 kHz Meas BW, 900 MHz
-50
-60
17
800
-25
850
900
Frequency (MHz)
950
1000
800
-70
850
900
950
1000
Frequency (MHz)
12
13
14
15
16
17
18
19
Output Channel Power (dBm)
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Information
1900 MHz Application Circuit (AH118-89PCB1900)
Vcc = +5 V
Typical RF Performance at 25°C
Frequency
S21 – Gain
S11 – Input Return Loss
S22 – Output Return Loss
Output P1dB
Output IP3
(+17 dBm / tone, 1 MHz spacing)
Channel Power
(@-45 dBc ACPR, IS-95 9 channels fwd)
Noise Figure
Device / Supply Voltage
Quiescent Current
1900 MHz
16.5 dB
-12 dB
-18 dB
+24.7 dBm
All passive components are of size 0603 unless otherwise noted.
+40.5 dBm
PORT
P=1
Z=50 Ohm
CAP
ID=C1
C=1e5 pF
size 1206
CAP
ID=C2
C=1000 pF
The diode D1 is used as over-voltage protection on the evaluation
boards. It is not specifically required in the final circuit layout in
a system using a DC regulator.
DIODE1
ID=D1
5.6 V
Component R1 is shown in the silkscreen but is not used for this
configuration.
L3 - the 0 ohm resistor - can be removed (with a thru line) in the
final circuit layout.
CAP
ID=C4
C=100 pF
CAP
ID=C3
C=56 pF
size 0805
IND
ID=L1
L=18 nH
size 0805
IND
ID=L2
L=4.7 nH
CAP
ID=C5
C=100 pF
PORT
P=2
Z=50 Ohm
+18 dBm
4.3 dB
+5 V
160 mA
RES
ID=L3
R=0 Ohm
SUBCKT
ID=U1
NET="AH118"
CAP
ID=C7
C=2.4 pF
CAP
ID=C9
C=1.2 pF
C7 should be placed at the silk screen
marker "A" on the WJ evaluation board.
The capacitor should be placed
20.7° @ 1.9GHz from pin 3
of the AH118.
The capacitor should be placed
2.6° @ 1.9GHz from pin 1 of the AH118
Gain
Return Loss
18
0
17
-5
16
-10
15
-15
14
-20
C9 should be placed between
silk screen markers '4' and '5'
on the WJ evaluation board.
ACPR vs. Channel Power
S11
-40
S22
IS-95, 9 Ch. Fwd, ±885 kHz offset, 30 kHz Meas BW, 1900 MHz
-50
-60
13
1800
-70
-25
1850
1900
Frequency (MHz)
1950
2000
1800
1850
1900
1950
2000
Frequency (MHz)
12
13
14
15
16
17
18
19
Output Channel Power (dBm)
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Information
2140 MHz Application Circuit (AH118-89PCB2140)
Vcc = +5 V
Typical RF Performance at 25°C
Frequency
S21 – Gain
S11 – Input Return Loss
S22 – Output Return Loss
Output P1dB
Output IP3
(+17 dBm / tone, 1 MHz spacing)
Channel Power
2140 MHz
16.3 dB
-15 dB
-16 dB
+24.7 dBm
All passive components are of size 0603 unless otherwise noted.
+40.5 dBm
PORT
P=1
Z=50 Ohm
CAP
ID=C1
C=1e5 pF
size 1206
CAP
ID=C2
C=1000 pF
The diode D1 is used as over-voltage protection on the evaluation
boards. It is not specifically required in the final circuit layout in
a system using a DC regulator.
DIODE1
ID=D1
5.6 V
Component R1 is shown in the silkscreen but is not used for this
configuration.
CAP
ID=C4
C=100 pF
CAP
ID=C3
C=56 pF
size 0805
IND
ID=L1
L=18 nH
size 0805
CAP
ID=L2
C=1.5 pF
CAP
ID=C5
C=100 pF
+16.7 dBm
(@-45 dBc ACPR, IS-95 9 channels fwd)
Noise Figure
Device / Supply Voltage
Quiescent Current
4.8 dB
+5 V
160 mA
RES
ID=L3
R=0 Ohm
SUBCKT
ID=U1
NET="AH118"
CAP
ID=C6
C=1.8 pF
C9 should be placed at the
silk screen marker '5' on the
WJ evaluation board.
CAP
ID=C9
C=1 pF
C6 should be placed at the silk screen
marker "F" on the WJ evaluation board.
The capacitor should be placed
26.2° @ 2.14GHz from pin 3
of the AH118.
The capacitor should be placed
32° @ 2.14GHz from pin 1 of the AH118
Gain
Return Loss
ACLR vs. Channel Power
18
0
17
-5
-40
16
-10
-45
15
-15
-50
14
-20
-55
S11
13
2110
-35
S22
-25
2130
PORT
P=2
Z=50 Ohm
2150
Frequency (MHz)
2170
2110
3GPP W-CDMA, Test Model 1+64 DPCH, ±5 MHz offset, 2140 MHz
-60
2130
2150
2170
Frequency (MHz)
12
13
14
15
16
17
18
Output Channel Power (dBm)
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
AH118
The Communications Edge TM
¼ Watt, High Linearity InGaP HBT Amplifier
Product Information
Outline Drawing
Product Marking
The component will be marked with an
“AH118” designator with an a numeric lot
code on the top surface of the package. Tape
and reel specification for this part is located on
the website in the “Application Notes” section.
ESD / MSL Information
ESD Rating:
Value:
Test:
Standard:
Land Pattern
Class 1A
Passes between 250 and 500V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
MSL Rating: Level 3 at +235° C convection reflow
Standard:
JEDEC Standard J-STD-020A
Mounting Config. Notes
Thermal Specifications
Parameter
Rating
Operating Case Temperature
Thermal Resistance1
Junction Temperature2
-40 to +85° C
92° C / W
159° C
Notes:
1. The thermal resistance is referenced from the hottest
part of the junction to the ground tab (pin 4).
2. This corresponds to the typical biasing condition of
+5V, 160 mA at an 85° C ground tab temperature. A
minimum MTTF of 1 million hours is achieved for
junction temperatures below 247° C.
1. Ground / thermal vias are critical for the
proper performance of this device. Vias
should use a .35mm (#80 / .0135”) diameter
drill and have a final plated thru diameter
of .25 mm (.010”).
2. Add as much copper as possible to inner and
outer layers near the part to ensure optimal
thermal performance.
3. Mounting screws can be added near the part
to fasten the board to a heatsink. Ensure that
the ground / thermal via region contacts the
heatsink.
4. Do not put solder mask on the backside of the
PC board in the region where the board
contacts the heatsink.
5. RF trace width depends upon the PC board
material and construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches).
Angles are in degrees.
AH118 MTTF vs. GND Tab Temperature
100000
10000
1000
100
60
70
80
90
100
110
120
Tab Temperature (°C)
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: [email protected] • Web site: www.wj.com
May 2004
Similar pages