MIC HERF1601 High efficiency glass passivated rectifier Datasheet

HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER
HERF1601 THRU HERF1607
VOLTAGE RANGE
50 to 1000 Volts
CURRENT
16.0 Ampere
FEATURES
•
•
•
•
•
•
•
•
•
ITO-220AC
High speed switching
Glass passivated chip junction
Low power loss for high efficiency
Low leakage
High surge capacity
High temperature soldering guaranteed
250℃/10 second, 0.16”(4.06mm) lead length
Also available in reverse polarity, add the “R” Suffix,
i.e. HERF1601R
Also available in the single chip version, HER1601
MECHANICAL DATA
•
•
•
•
•
•
Case: Transfer molded plastic
Epoxy: UL94V-0 rate flame retardant
Lead: solderable per MIL-STD-202E method 208C
Polarity: as marked
Mounting position: Any, 5 in-lbs Torque Max
Weight: 0.08 ounce, 2.24 gram
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
HERF HERF
SYMBOLS
1601
1602
Maximum Repetitive Peak Reverse Voltage
VRRM
50
100
Maximum RMS Voltage
VRMS
35
70
Maximum DC Blocking Voltage
VDC
50
100
•
•
Maximum Average Forward Rectified Current
At Tc=100℃
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC method)
Maximum Instantaneous Forward Voltage per at 16.0A
Maximum DC Reverse Current at rated TA = 25℃
DC Blocking Voltage at
T = 125℃
HERF
1603
200
140
200
Typical Thermal Resistance (Note 1)
Operating Junction Temperature
Storage Temperature Range
HERF
1605
400
280
400
HERF
1606
600
420
600
HERF
1607
800
560
800
UNIT
Volts
Volts
Volts
I(AV)
16.0
Amps
IFSM
225
Amps
VF
1.0
1.3
IR
trr
1.5
1.7
10
500
A
Maximum Reverse Recovery Time
Test conditions lF=0.5A, lR=1.0A, lRR=0.25A
Typical Junction Capacitance
(Measured at 1.0MHz and applied reverse voltage of 4.0V)
HERF
1604
300
210
300
70
Volts
µA
100
nS
CJ
40
pF
RθJC
TJ
TSTG
3.0
(-55 to +150)
(-55 to +150)
℃/W
NOTES:
1. Unit mounted on heatsink
E-mail: [email protected]
Web Site: www.cnmic.com
℃
℃
HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER
HERF1601 THRU HERF1607
VOLTAGE RANGE
50 to 1000 Volts
CURRENT
16.0 Ampere
RATING AND CHRACTERISTIC CURVES HERF1601 THRU HERF1607
FIG.2-MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
20
16
12
8.0
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.375″(9.5mm) Lead Length
4.0
300
CURRENT, (A)
PEAK FORWARD SURGE
24
(A)
AVERAGE FORWARD CURRENT,
FIG.1-TYPICAL FORWARD CURRENT
DERATING CURVE
8.3ms Single Half Sine-Wave
(JEDEC Method) T= Tjmax
200
100
1 Cycle
0
0
25
50
100
75
125
175
150
0
1
2
AMBIENT TEMPERATURE, (° C)
4
6
8
10
40
20
60
100
NUMBER OF CYCLES AT 60 Hz
FIG.4-TYPICAL REVERSE
CHARACTERISTICS PER LEG
100
FIG.3-TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS PER LEG
INSTANTANEOUS REVERSE CURRENT,
(μA)
V
/4
00
0
60
0
/8
0V
50
/ 10
0/2
30
0
00
V
10
(A)
INSTANTANEOUS FORWARD CURRENT,
TJ =125° C
100
1.0
TJ =25° C
Pulse Width=300us
1% Duty Cycle
0.1
0.4
0.8
10
1.0
TJ=25° C
0.1
1.6
1.2
INSTANTANEOUS FORWARD VOLTAGE,(V)
0.01
0
20
FIG.5-TYPICAL JUNCTION CAPACITANCE
40
60
100
80
120
140
PERCENT OF RATED PEAK
PER LEG
REVERSE VOLTAGE,(%)
JUNCTION CAPACITANCE,(pF)
100
F1G.6-TEST CIRCUIT DIAGRAM AND
REVERSE RECOVERY TIME CHARACTERISTIC
Trr
50Ω
10Ω
NONINDUCTIVE NONINDUCTIVE
+0.5A
(-)
10
(+)
25 Vdc
(approx.)
(-)
TJ =25° C
f=1MHz
Vsig=50mVp-p
1.0
1Ω
NON
INDUCTIVE
PULSE
GENERATIOR
(NOTE 2)
0
-0.25A
(+)
OSCILLOSCOPE
(NOTE 1)
-1.0A
1
0.1
D.U.T.
10
100
REVERSE VOLTAGE,(V)
E-mail: [email protected]
NOTES : 1.Rise Time=7ns mas. Input Impedance=
1 magohm. 22pF
2.Rise time=10ns max. Source Impedance=
50 ohms
Web Site: www.cnmic.com
1cm
SET TIME BASE FOR
50/100ns/cm
Similar pages