Pan Jit ER2E Surface mount rectifier Datasheet

DATA SHEET
ER2A~ER2J
SURFACE MOUNT RECTIFIER
VOLTAGE
50 to 600 Volts
2.0 Amperes
CURRENT
SMB/DO-214AA
Unit: inch (mm)
FEATURES
• For surface mounted applications
.155(3.94)
.130(3.30)
• High temperature metallurgically bonded-no compression
contacts as found in other diode-constructed rectifiers
.083(2.11)
• Built-in strain relief
• Easy pick and place
.075(1.91)
• Glass passivated junction
.185(4.70)
.160(4.06)
• Plastic package has Underwriters Laboratory Flammability
Classification 94V-O
.012(.305)
.006(.152)
environment substance directive request
.083(2.13)
.096(2.44)
• Pb free product are available : 99% Sn above can meet Rohs
.050(1.27)
.030(0.76)
MECHANICALDATA
.008(.203)
.002(.051)
Case: JEDEC DO-214AA molded plastic
.220(5.59)
.200(5.08)
Terminals: Solder plated, solderable per MIL-STD-202G,
Method 208
Polarity: Indicated by cathode band
Standard packaging: 16mm tape (EIA-481)
Weight: 0.003 ounce, 0.093 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
PA R A M E TE R
S YM B O L
E R 2A
E R 2B
E R 2C
E R 2D
E R 2E
E R 2G
E R 2J
U N ITS
M axim um R ecurrentP eak R everse Voltage
V RRM
50
100
150
200
300
400
600
V
M axim um R M S Voltage
V RM S
35
70
105
140
210
280
420
V
M axim um D C B locking Voltage
VDC
50
100
150
200
300
400
600
V
M axim um A verage Forw ard C urrent.375"(9.5m m )
lead length atTL=110O C
P eak Forw ard S urge C urrent:8.3m s single halfsine-w ave
superim posed on rated load(JE D E C m ethod)
IAV
2.0
A
IFSM
50
A
M axim um Forw ard Voltage at2.0A
VF
M axim um D C R everse C urrentTA =25 O C
atR ated D C B locking VoltageTA =100 O C
IR
5.0
150
uA
M axim um R everse R ecovery Tim e (N ote 1)
TRR
35
ns
TypicalJunction capacitance (N ote 2)
CJ
25
pF
M axim um therm alR esistance (N ote 3)
RθJL
20
TJ,TSTG
-50 TO +150
O perating Junction and S torage Tem perature R ange
0.95
1.25
1.7
V
O
C /W
O
C
NOTES:1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A
2. Measured at 1 MHz and applied Vr = 4.0 volts.
3. 8.0 mm2 ( .013mm thick ) land areas.
STAD-DEC.13.2004
PAGE . 1
RATING AND CHARACTERISTIC CURVES
70
AVERAGE FORWARD RECIFIED
CURRENT AMPERES
2.8
60
2.4
1.6
1 .2
.8
SINGLE PHASE, HALF-WAVE, 60Hz RESISTIVE
OR INDUCTIVE LOAD P.C.B MOUNTED
ON 0.3 x 0.3" (8.0 x 8.0 mm)COPPER PAD AREAS
.4
0
0
20
40
60
50
CAPACITANCE, pF
2 .0
40
30
20
TJ = 25 C
f = 1.0MHZ
Vsig = 50mVp-p
O
10
80
100
120
140
160
180
0
O
LEAD TEMPERATURE, C
0.1
1
10
100
1000
REVERSE VOLTAGE, VOLTS
FIG.2 TYPICAL JUNCTION CAPACITANCE
FIG.1 MAXIMUM AVERAGE FORWARD CURRENT RATING
INSTANTANEOUS FORWARD CURRENT AMPERES
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
100
TJ=100 C
O
100
10
TJ=75 C
O
TJ=25 C
O
1.0
0.1
0.01
2
40
60
80
60
80
100 120 140
PERCENT OF RATED PEAK REVERSE VOLTGE, VOLTS
FIG.3 TYPICAL REVERSE CHARACTERISTICS
300-400V
10
50-200V
600V
1.0
0.1
O
T J = 25 C
.01
0
0.4
0.8
1.2
1.6
2.0
2.4
2.8
INSTANTANEOUS FORWARD VOLTAGE VOLTS
FIG.4 TYPICAL FORWARD CHARACTERISTICS
FORWARD SURGE CURRENT, AMPERES
(HALF-SING WAVE)
60
50
40
30
20
10
0
8.3ms SINGLE HALF SINE-WAVE
JEDC METHOD
1
5
10
50
100
NUMBER OF CYCLES AT 60Hz
FIG.5 MAXIMUM NON-REPEITIVE SURGE CURRENT
STAD-DEC.13.2004
PAGE . 2
Similar pages