Standard ICs Dual high slew rate operational amplifier BA4560 / BA4560F / BA4560N The BA4560, BA4560F, and BA4560N are dual operational amplifiers which achieve approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. The following packages are available: 8-pin DIP (BA4560), 8-pin SOP (BA4560F), and 8-pin SIP (BA4560N). Applications •Active filters Audio amplifiers VCOs Other electronic circuits •1)Features Built-in output short-circuit protection circuit. 2) Internal phase correction. 3) No latch-up. 4) Wide range of common-mode modes and differential voltage. 5) High gain and low noise. •Block diagram BA4560N BA4560 / BA4560F OUT1 1 8 VCC – IN1 2 7 OUT2 6 – IN2 5 + IN2 3 4 5 6 7 8 + IN1 VEE + IN2 – IN2 OUT2 VCC – 2 2ch + – IN1 VEE 4 + 1 + IN1 3 + 2ch – OUT1 1ch – + 1ch – 1 Standard ICs BA4560 / BA4560F / BA4560N •Internal circuit configuration VCC R1 Q7 Q5 Q13 Q11 Q8 – IN Q1 R6 Q2 Q15 Q9 R7 R5 + IN R8 Q12 Q14 Q6 Q3 OUT Q10 Q4 R3 R2 R9 R4 D VEE •Absolute maximum ratings (Ta = 25°C) Parameter Symbol Power supply voltage Limits BA4560 BA4560F ± 18 VCC ± 18 800∗ ± 18 550∗ Power dissipation Pd Differential input voltage VID ± VCC VI – VCC ~ VCC Common-mode input voltage Unit BA4560N V 900∗ mW V V Operating temperature Topr – 40 ~ + 85 °C Storage temperature Tstg – 55 ~ + 125 °C ∗ Refer to the Pd characteristics diagram. The values for the BA4560F are those when it is mounted on a glass epoxy PCB (50mm × 50mm × 1.6mm). •Electrical characteristics (unless otherwise noted, Ta = 25°C, V CC Parameter Symbol Min. Typ. Input offset voltage VIO — Input offset current IIO — Max. Unit 0.5 6.0 mV 5 200 nA Conditions RS ⬉ 10kΩ Input bias current IB — 50 500 nA High-amplitude voltage gain AV 86 100 — dB Common-mode input voltage VICM ± 12 ± 14 — V Maximum output voltage 1 VOM1 ± 12 ± 14 — V RL ⭌ 10kΩ Maximum output voltage 2 VOM2 ± 10 ± 13 — V RL ⭌ 2kΩ RL ⭌ 2kΩ, VO = ± 10V Common-mode rejection ratio CMRR 70 90 — dB RS ⬉ 10kΩ Power supply voltage rejection ratio PSRR — 30 150 µV / V RS ⬉ 10kΩ Slew rate S. R. — 4.0 — V / µs AV = 1, RL = 2kΩ Vn — — 2.2 µV GBW — 10 — MHz Input conversion noise voltage Gain band width product 2 = +15 V, VEE = -15 V) f = 10kHz Standard ICs BA4560 / BA4560F / BA4560N •Electrical characteristic curves 800 BA4560 600 BA4560F 400 200 0 0 25 50 7585 100 125 3 80 60 40 20 0 ± 20 1 10 100 1k 10k 100k 1M 10M FREQUENCY: f (Hz) Fig.1 Power dissipation vs. ambient temperature Fig.2 Quiescent current vs. power supply voltage Fig.3 Open loop voltage gain vs. frequency 75 80 INPUT BIAS CURRENT: IR (nA) 28 24 20 16 12 8 60 40 50 4 1k 10k 100k 20 1M – 20 0 –5 5 0 –5 20 30 40 TIME (µs) Fig.7 Output response characteristics INPUT COMMON MODE VOLTAGE RANGE: VICM (V) 5 10 20 40 60 80 25 0 10 20 30 40 + POWER SUPPLY VOLTAGE: V (V) Fig.6 Input bias current vs. power supply voltage Fig.5 Input bias current vs. ambient temperature Fig.4 Maximum output voltage vs. frequency 0 0 AMBIENT TEMPERATURE: Ta (°C) FREQUENCY: f (Hz) OUTPUT VOLTAGE VOUT (V) 100 POWER SUPPLY VOLTAGE: VCC (V) 0 100 INPUT VOLTAGE VIN (V) ± 10 0 120 AMBIENT TEMPERATURE: Ta (°C) 32 MAXIMUM OUTPUT VOLTAGE: VOM (V) 4 2 150 OPEN LOOP VOLTAGE GAIN: AV (dB) BA4560N INPUT BIAS CURRENT: IB (nA) 1000 140 5 QUIESCENT CURRENT: IQ (mA) POWER DISSIPATION: Pd (mW) 1200 20 10 0 – 10 – 20 0 ± 10 ± 20 ± POWER SUPPLY VOLTAGE: V (V) Fig.8 Common mode input voltage vs. power supply voltage 3 Standard ICs BA4560 / BA4560F / BA4560N notes •(1)Operation Handling unused circuits VCC If there are any circuits which are not being used, we recommend making connections as shown in Figure 9, with the non-inverted input pin connected to the potential within the in-phase input voltage range (VICM). – To potential in VICM + VEE Fig.9 Unused circuit connections •Exteral dimensions (Units: mm) BA4560 BA4560F 0.3 ± 0.1 0.5 ± 0.1 0° ~ 15° 2.54 1 4 1.27 0.15 ± 0.1 7.62 5 4.4 ± 0.2 6.2 ± 0.3 4 8 1.5 ± 0.1 1 5.0 ± 0.2 0.11 5 6.5 ± 0.3 8 0.51Min. 3.2 ± 0.2 3.4 ± 0.3 9.3 ± 0.3 0.4 ± 0.1 0.3Min. 0.15 DIP8 SOP8 BA4560N 1.2 5.8 ± 0.2 2.8 ± 0.2 8 1 3.5 ± 0.5 10.5 ± 0.5 19.3 ± 0.2 2.54 0.6 0.8 1.3 SIP8 4 0.3 ± 0.1