Illumination LUXEON 5050 High efficacy and lumens in a multi-die, high power package, enabling low system costs LUXEON 5050 is a multi-die, high power package that provides high luminance from a single package to enable cost effective, single optic and directional fixture designs. LUXEON 5050 uses an industry standard 5050 surface mount package with the smallest round Light Emitting Surface (LES). LUXEON 5050 comes in 70CRI, 80CRI and 90CRI with a wide range of CCTs, and offers hot-color targeting to ensure that the LEDs are within color target at application conditions of 85°C. Features and Benefits Primary Applications Small LES (4.6mm) enables good optic design for great punch Downlights Enables highest efficacy system design by driving at low current High Bay & Low Bay Hot-color targeting ensures color is within ANSI bin at 85°C Lamps Binned within 3-step and 5-step MacAdam ellipse, ensuring color uniformity Outdoor Compatible with low cost and high efficacy drivers Spotlights DS174 LUXEON 5050 Product Datasheet ©2018 Lumileds Holding B.V. All rights reserved. No. E352519 Table of Contents General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Characteristic Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Spectral Power Distribution Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Radiation Pattern Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Product Bin and Labeling Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Decoding Product Bin Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Color Bin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Reflow Soldering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Pocket Tape Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. i General Product Information Product Test Conditions LUXEON 5050 LEDs are tested with a 20ms monopulse of 160mA for LUXEON 5050 24V and 640mA for LUXEON 5050 6V at a junction temperature, Tj, of 25°C. Forward voltage and luminous flux are binned at a Tj of 25°C, while color is hot targeted at a Tj of 85°C. Part Number Nomenclature Part numbers for LUXEON 5050 follow the convention below: L 1 5 0 – A A B B 5 0 C C 0 0 0 0 0 Where: A A – designates nominal ANSI CCT (27=2700K, 30=3000K, 35=3500K 40=4000K, 50=5000K, 57=5700K, 65=6500K) B B – designates minimum CRI (70=70CRI, 80=80CRI, 90=90CRI) C C – designates voltage (06=6V, 24=24V) Therefore, the following part number is used for a LUXEON 5050, 3000K 80CRI, 24V: L 1 5 0 – 3 0 8 0 5 0 2 4 0 0 0 0 0 Lumen Maintenance Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the longterm performance of this product. Environmental Compliance Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON 5050 is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 2 Performance Characteristics Product Selection Guide Table 1. Product performance of LUXEON 5050 at test current, Tj=25°C. VOLTAGE 24V 6V Nominal CCT [1] Minimum CRI [2, 3] 2700K 3000K Luminous Flux [2, 3] (lm) Typical Luminous Efficacy (lm/W) TEST CURRENT (mA) Part Number Minimum Typical 70 535 600 153 160 L150-2770502400000 70 553 620 158 160 L150-3070502400000 4000K 70 580 650 166 160 L150-4070502400000 5000K 70 580 650 166 160 L150-5070502400000 5700K 70 570 650 166 160 L150-5770502400000 6500K 70 570 650 166 160 L150-6570502400000 2700K 80 500 560 143 160 L150-2780502400000 3000K 80 516 585 149 160 L150-3080502400000 3500K 80 527 595 152 160 L150-3580502400000 4000K 80 539 610 156 160 L150-4080502400000 5000K 80 539 610 156 160 L150-5080502400000 5700K 80 539 610 156 160 L150-5780502400000 6500K 80 539 610 156 160 L150-6580502400000 2700K 90 414 471 120 160 L150-2790502400000 3000K 90 428 486 124 160 L150-3090502400000 3500K 90 445 506 129 160 L150-3590502400000 4000K 90 456 526 134 160 L150-4090502400000 5000K 90 456 526 134 160 L150-5090502400000 5700K 90 456 526 134 160 L150-5790502400000 2700K 70 535 600 153 640 L150-2770500600000 3000K 70 553 620 158 640 L150-3070500600000 4000K 70 580 650 166 640 L150-4070500600000 5000K 70 580 650 166 640 L150-5070500600000 5700K 70 570 650 166 640 L150-5770500600000 6500K 70 570 650 166 640 L150-6570500600000 2700K 80 500 560 143 640 L150-2780500600000 3000K 80 516 585 149 640 L150-3080500600000 3500K 80 527 595 152 640 L150-3580500600000 4000K 80 539 610 156 640 L150-4080500600000 5000K 80 539 610 156 640 L150-5080500600000 5700K 80 539 610 156 640 L150-5780500600000 6500K 80 539 610 156 640 L150-6580500600000 2700K 90 414 471 120 640 L150-2790500600000 3000K 90 428 486 124 640 L150-3090500600000 3500K 90 445 506 129 640 L150-3590500600000 4000K 90 456 526 134 640 L150-4090500600000 5000K 90 456 526 134 640 L150-5090500600000 5700K 90 456 526 134 640 L150-5790500600000 Notes for Table 1: 1. Correlated color temperature is hot targeted at Tj=85°C. 2. Luminous flux and CRI are based upon mounted package on highly reflective surface at Tj=25°C. Typical CRI is approximately 2 points higher than the minimum CRI specified, but this is not guaranteed. 3. Lumileds maintains a tolerance of ±2 on CRI and ±7% on luminous flux measurements. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 3 Optical Characteristics Table 2. Optical characteristics for LUXEON 5050 at test current, Tj=25°C. Part Number Typical Total Included Angle [1] Typical Viewing Angle [2] L150-xxxx50xx00000 138° 116° Notes for Table 2: 1. Total angle at which 90% of total luminous flux is captured. 2. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is ½ of the peak value. Electrical and Thermal Characteristics Table 3. Electrical and thermal characteristics for LUXEON 5050 at test current, Tj=25°C. Forward Voltage [1] (Vf) Typical Thermal Resistance—Junction to Solder Pad (°C/W) Minimum Typical MAXIMUM Typical Temperature Coefficient of Forward Voltage [2] (mV/°C) L150-xxxx502400000 23.5 24.5 26.5 -12 2 L150-xxxx500600000 5.8 6.1 6.6 -3 2 Part Number Notes for Table 3: 1. Lumileds maintains a tolerance of ±1% on forward voltage measurements. 2. Measured between 25°C and 85°C. Absolute Maximum Ratings Table 4. Absolute maximum ratings for LUXEON 5050. Parameter Maximum Performance DC Forward Current [1, 2] 240mA for 24V 800mA for 6V Peak Pulsed Forward Current [1, 3] 300mA for 24V 1000mA for 6V LED Junction Temperature [1] (DC & Pulse) 125°C ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 2 Operating Case Temperature [1] 105°C LED Storage Temperature -40°C to 105°C Reverse Voltage (Vreverse) LUXEON LEDs are not designed to be driven in reverse bias Notes for Table 4: 1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met: – The frequency of the ripple current is 100Hz or higher – The average current for each cycle does not exceed the maximum allowable DC forward current – The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current 3. At 10% duty cycle with pulse width of 10ms. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 4 Characteristic Curves Spectral Power Distribution Characteristics Figure 1a. Typical normalized power vs. wavelength for L150-xx7050xx00000 at test current, Tj=25°C. Figure 1b. Typical normalized power vs. wavelength for L150-xx8050xx00000 at test current, Tj=25°C. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 5 Figure 1c. Typical normalized power vs. wavelength for L150-xx9050xx00000 at test current, Tj=25°C. Light Output Characteristics Figure 2. Typical normalized light output vs. junction temperature for L150-xxxx50xx00000 at test current. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 6 Figure 3a. Typical normalized light output vs. forward current for L150-xxxx502400000, Tj=25°C. Figure 3b. Typical normalized light output vs. forward current for L150-xxxx500600000, Tj=25°C. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 7 Forward Current Characteristics Figure 4a. Typical forward current vs. forward voltage for L150-xxxx502400000, Tj=25°C. Figure 4b. Typical forward current vs. forward voltage for L150-xxxx500600000, Tj=25°C. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 8 Radiation Pattern Characteristics Figure 5. Typical radiation pattern for L150-xxxx50xx00000 at test current, Tj=25°C. Figure 6. Typical polar radiation pattern for L150-xxxx50xx00000 at test current, Tj=25°C. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 9 Product Bin and Labeling Definitions Decoding Product Bin Labeling In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical datasheet. For this reason, Lumileds bins LED components for luminous flux or radiometric power, color point, peak or dominant wavelength and forward voltage. LUXEON 5050 LEDs are labeled using a 4-digit alphanumeric CAT code following the format below: A B C C Where: A – designates luminous flux bin (example: H=450 to 500 lumens, L=600 to 650 lumens) B – designates color bin (example: (example: 3=3 SDCM, 5=5 SDCM parts) C C – designates forward voltage bin (example: A1, A2, B1, B2) Therefore, a LUXEON 5050 with a lumen range of 600 to 650, color bin of 3 and forward voltage range of 23.5 to 24.2V has the following CAT code: L3A1 Luminous Flux Bins Table 5 lists the standard luminous flux bins for LUXEON 5050 LEDs. Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs. Table 5. Luminous flux bin definitions for LUXEON 5050, Tj=25°C. Bin Luminous Flux [1] (lm) Minimum Maximum G 400 450 H 450 500 J 500 550 K 550 600 L 600 650 M 650 700 N 700 750 Notes for Table 5: 1. Lumileds maintains a tolerance of ±7% on luminous flux measurements. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 10 Color Bin Definitions Figure 7. 3- and 5-step MacAdam ellipse illustration for hot-color targeting expected at 85°C. Table 6. 3- and 5-step MacAdam ellipse color bin definitions for LUXEON 5050 at test current, hot-color targeted at Tj=85°C. Nominal CCT Color Space Center Point [1] (cx, cy) Major Axis, a Minor Axis, b Ellipse Rotation Angle, θ 2700K Single 3-step MacAdam ellipse (0.4578, 0.4101) 0.00810 0.00420 53.70° 3000K Single 3-step MacAdam ellipse (0.4338, 0.4030) 0.00834 0.00408 53.22° 3500K Single 3-step MacAdam ellipse (0.4073, 0.3917) 0.00927 0.00414 54.00° 4000K Single 3-step MacAdam ellipse (0.3818, 0.3797) 0.00939 0.00402 53.72° 5000K Single 3-step MacAdam ellipse (0.3447, 0.3558) 0.00822 0.00354 59.62° 5700K Single 3-step MacAdam ellipse (0.3287, 0.3417) 0.00745 0.00320 59.09° 6500K Single 3-step MacAdam ellipse (0.3123, 0.3282) 0.00669 0.00285 58.57° 2700K Single 5-step MacAdam ellipse (0.4578, 0.4101) 0.01350 0.00700 53.70° 3000K Single 5-step MacAdam ellipse (0.4338, 0.4030) 0.01390 0.00680 53.22° 3500K Single 5-step MacAdam ellipse (0.4073, 0.3917) 0.01545 0.00690 54.00° 4000K Single 5-step MacAdam ellipse (0.3818, 0.3797) 0.01565 0.00670 53.72° 5000K Single 5-step MacAdam ellipse (0.3447, 0.3558) 0.01370 0.00590 59.62° 5700K Single 5-step MacAdam ellipse (0.3287, 0.3417) 0.01243 0.00533 59.09° 6500K Single 5-step MacAdam ellipse (0.3123, 0.3282) 0.01115 0.00475 58.57° Notes for Table 6: 1. Lumileds maintains a tolerance of ±0.01 on x and y coordinates in the CIE 1931 color space. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 11 Forward Voltage Bins Table 7. Forward voltage bin definitions for LUXEON 5050, Tj=25°C. PART NUMBER L150-xxxx502400000 L150-xxxx500600000 Forward Voltage [1] (Vf) Bin Minimum Maximum A1 23.5 24.2 A2 24.2 25.0 B1 25.0 25.8 B2 25.8 26.5 A1 5.8 6.0 A2 6.0 6.2 B1 6.2 6.4 B2 6.4 6.6 Notes for Table 7: 1. Lumileds maintains a tolerance of ±1% on forward voltage measurements. Mechanical Dimensions Figure 8. Mechanical dimensions for LUXEON 5050. Notes for Figure 8: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 12 Reflow Soldering Guidelines tp Tp Critical Zone TL to Tp Ramp-up TL Temperature tL Tsmax Tsmin Ramp-down ts Preheat Area 25 Time 25ºC to Peak JEDEC J-STD-020D Time Figure 9. Visualization of the acceptable reflow temperature profile as specified in Table 8. Table 8. Reflow profile characteristics for LUXEON 5050. PROFILE FEATURE Lead-Free Assembly Preheat Minimum Temperature (Tsmin) 150°C Preheat Maximum Temperature (Tsmax) 200°C Preheat Time (tsmin to tsmax) 60 to 180 seconds Ramp-Up Rate (TL to Tp) 3°C / second maximum Liquidus Temperature (TL) 217°C Time Maintained Above Temperature TL (tL) 60 to 150 seconds Peak / Classification Temperature (Tp) 260°C Time Within 5°C of Actual Temperature (tp) 20 to 40 seconds Ramp-Down Rate (Tp to TL) 6°C / second maximum Time 25°C to Peak Temperature 8 minutes maximum JEDEC Moisture Sensitivity Table 9. Moisture sensitivity levels for LUXEON 5050. level 3 Floor Life Soak Requirements Standard TIme Conditions Time Conditions 168 Hours ≤30°C / 60% RH 192 Hours +5 / -0 30°C / 60% RH DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 13 Solder Pad Design Figure 10. Recommended PCB solder pad layout for LUXEON 5050. Notes for Figure 10: 1. Drawings are not to scale. 2. All dimensions are in millimeters. Packaging Information Pocket Tape Dimensions Figure 11. Pocket tape dimensions for LUXEON 5050. Notes for Figure 11: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 14 0.3 10 Front 0 51 Back 0. 3 Reel Dimensions 10 Back View 3 Front View Figure 12. Reel dimensions for LUXEON 5050. Notes for Figure 12: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS174 LUXEON 5050 Product Datasheet 20180207 ©2018 Lumileds Holding B.V. All rights reserved. 15 About Lumileds Companies developing automotive, mobile, IoT and illumination lighting applications need a partner who can collaborate with them to push the boundaries of light. With over 100 years of inventions and industry firsts, Lumileds is a global lighting solutions company that helps customers around the world deliver differentiated solutions to gain and maintain a competitive edge. As the inventor of Xenon technology, a pioneer in halogen lighting and the leader in high performance LEDs, Lumileds builds innovation, quality and reliability into its technology, products and every customer engagement. Together with its customers, Lumileds is making the world safer, better and more beautiful—with light. To learn more about our lighting solutions, visit lumileds.com. ©2018 Lumileds Holding B.V. All rights reserved. LUXEON is a registered trademark of the Lumileds Holding B.V. in the United States and other countries. lumileds.com DS174 LUXEON 5050 Product Datasheet 20180207 Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials and services information and data are provided “as is,” and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data. A listing of Lumileds product/patent coverage may be accessed at lumileds.com/patents.