Toggles Series LP01 Short Body Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Power Level (silver): Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Materials & Finishes Actuator: Housing: Base: Movable Contact: Stationary Contacts: Lamp Terminals: Tilt Tactiles Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Standards & Certifications Flammability Standards: UL: 50 milliohms maximum 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum 500,000 operations minimum 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC 1.5N for Single Pole; 3.0N for Double Pole Nonshorting (break-before-make) Total Travel .118” (3.0mm) Polycarbonate Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polyphenylene ether (UL94V-0) Diallyl phthalate (UL94V-0) Phosphor bronze & silver with silver plating Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin & copper plating Phospher bronze with tin and copper plating –10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (+13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 0.8Nm (7.08 lb • in) Manual Soldering: See Profile A in Supplement section. Hand clean locally with alcohol based solution UL94V-0 housing & base File No. E44145 All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. Supplement Accessories Indicators Touch Mounting Torque: Soldering Time & Temperature: Cleaning: 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC D66 www.nkk.com Toggles Series LP01 Rockers Distinctive Characteristics Pushbuttons Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials. Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering. D Keylocks Bright LED illumination in choice of red, green, or amber through translucent white cap. Programmable Illuminated PB Short Body Pushbuttons Rotaries Short body of .551” (14.0mm) conserves behind-panel space. Slides Combination solder lug and .110” quick connect terminals. Touch Tilt Tactiles Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover. Supplement Accessories Indicators Actual Size www.nkk.com D67 Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 1 5 Poles C SPDT C Bushing 2 DPDT M Snap-in Circuit ON Housing (ON) K LEDs Black ( ) = Momentary Red Slides B 5D Amber 5F Green Cap Color B White Nonilluminated Cap Colors No Nonilluminated Code Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Rotaries 5C Nonilluminated IMPORTANT: A Black C Red F Green * Wire harness & cable assemblies offered only in Americas DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Tactiles LP0115CCKW015CB White Cap Red LED SPDT ON-(ON) Circuit Bushing Mount Black Housing Tilt Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals POLES & CIRCUIT Touch Indicators Accessories 5C Contacts & Terminals D 5 W01 K Silver Rated 3A @ 125V AC/250V AC W01 Solder Lug/ Quick Connect Terminals* Plunger Position ( ) = Momentary Supplement C Mounting Types 1 Keylocks Programmable Illuminated PB Pushbuttons Rockers LP01 Connected Terminals Throw & Power/Lamp Schematics Normal Down Normal Down 1-3 1-2 Pole Model SP LP0115 ON (ON) DP LP0125 ON (ON) Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch. 1 (COM) 1-3 4-6 1-2 4-5 SPDT 3 1 (COM) DPDT 3 D68 www.nkk.com L (+) (-) L L (+) (-) L 2 2 4 6 5 Series LP01 Toggles Short Body Pushbuttons MOUNTING TYPES M Snap-in .630” (16.0mm) Diameter Rockers Bushing .669” (17.0mm) Diameter Recommended Panel Thickness: 0.2 (18.1) +– 0.0 .713 (1.7) +– 0.0 0.1 .067 0.2 (16.0) +– 0.0 Dia .630 Pushbuttons This mounting option is supplied with a brass hexagon nut with nickel plating. Recommended Panel Thickness: 0.1 (7.5) –+ 0.0 .295 .079” ~ .256” (2.0mm ~ 6.5mm) .039” ~ .126” (1.0mm ~ 3.2mm) (25.0) Min .984 (17.3) .681 (21.0) Min .827 Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side. D 0.2 (1.1) +– 0.0 R .043 + 0.2 – 0.0 Dia Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side. K Black Keylocks HOUSING Housing available in black only. The one-piece body and bezel have a matte finish. Solder Lug/ .110” (2.8mm) Quick Connect Power Level Epoxy Seal 3A @ 125V AC/250V AC; 3A @ 30V DC (7.3) .287 (2.0) .079 (2.8) .110 (0.6) R .024 Slides Silver Rotaries CONTACT MATERIALS, RATINGS, & TERMINALS W01 (1.2) .047 Thk = (0.5) .020 Tactiles Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum. LED COLORS & SPECIFICATIONS 5D 5F Red Amber Green Forward Peak Current I FM 30mA 30mA 30mA Continuous Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.95V 2.0V 2.1V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆I F 0.41mA/°C 0.29mA/°C 0.39mA/°C No Code –10°C ~ +50°C Supplement Ambient Temperature Range Touch Colors 5C Indicators LEDs are an integral part of the switch and are not available separately. (-) Accessories (+) Tilt The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color LED with 1 Element Programmable Illuminated PB C No Lamp www.nkk.com D69 Series LP01 Toggles Short Body Pushbuttons CAP COLORS Illuminated Cap Rockers Cap Color Available: B The translucent cap is an integral part of the switch and is not available separately. White Finish: Matte Nonilluminated Caps Cap Colors Available: D A Black C Red F Green The cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte TYPICAL SWITCH DIMENSIONS Bushing Mount • Single Pole Rotaries Keylocks Programmable Illuminated PB Pushbuttons Material: Polycarbonate (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 (0.5) Typ .020 NO Slides Tactiles (2.5) .098 (7.3) .287 1 COM (3.0) .118 (5.55) .219 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 (13.6) Dia .535 (20.0) Dia .787 NC 3 NO (9.7) .382 Tilt LP0115CCKW015CB Touch Bushing Mount • Double Pole (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 NO (2.8) Typ .110 Accessories Supplement 3 (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 (5.5) .217 LP0125CCKW015CB D70 www.nkk.com (7.3) .287 (21.3) .838 NC 6 L –+ 2 1 5 4 COM (6.0) .236 (11.1) .437 NO Indicators (0.5) Typ .020 (9.7) .382 Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH DIMENSIONS Snap-in • Single Pole Rockers (3.7) .146 NO (2.5) .098 1 COM (3.0) .118 (5.55) .219 (7.3) .287 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 (13.6) Dia .535 (20.0) Dia .787 NC 3 NO (9.7) .382 Pushbuttons (0.5) Typ .020 D LP0115CMKW015CB Snap-in • Double Pole Keylocks (3.7) .146 (1.2) x (2.0) Typ .047 x .079 Programmable Illuminated PB (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NO (2.8) Typ .110 (9.7) .382 4 COM (7.3) .287 (6.0) .236 (11.1) .437 (21.3) .838 Slides (5.5) .217 5 LP0125CMKW015DB Tactiles (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 1 NO 6 L –+ 2 Rotaries NC 3 Tilt LEGENDS NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Methods: Epoxy based ink is recommended. (12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030 Accessories Pad Print or Laser Etch on cap. Shaded area is printable area Supplement R PW Indicators Touch Suggested Printable Area for LP01 Cap www.nkk.com D71