HY5PS561621A(L)FP
256Mb DDR2 SDRAM
HY5PS561621A(L)FP
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 0.4 / Sep. 2006
1
1
1HY5PS561621A(L)FP
Revision History
Rev.
0.1
0.2
History
Initial data sheet release.
Removed all contents on x4/8 Org.
Updated IDD Spec.
Draft Date
June. 2005
Oct. 2005
0.3
Removed improper note in ODT DC spec.
July 2006
0.4
Timing Parameters Table Modified
Sep. 2006
Rev. 0.4 / Sep. 2006
2
1
1HY5PS561621A(L)FP
Contents
1. Description
1.1 Device Features and Ordering Information
1.1.1 Key Feaures
1.1.2 Ordering Information
1.1.3 Ordering Frequency
1.2 Pin configuration
1.3 Pin Description
2. Maximum DC ratings
2.1 Absolute Maximum DC Ratings
2.2 Operating Temperature Condition
3. AC & DC Operating Conditions
3.1 DC Operating Conditions
5.1.1 Recommended DC Operating Conditions(SSTL_1.8)
5.1.2 ODT DC Electrical Characteristics
3.2 DC & AC Logic Input Levels
3.2.1 Input DC Logic Level
3.2.2 Input AC Logic Level
3.2.3 AC Input Test Conditions
3.2.4 Differential Input AC Logic Level
3.2.5 Differential AC output parameters
3.3 Output Buffer Levels
3.3.1 Output AC Test Conditions
3.3.2 Output DC Current Drive
3.3.3 OCD default chracteristics
3.4 IDD Specifications & Measurement Conditions
3.5 Input/Output Capacitance
4. AC Timing Specifications
5. Package Dimensions
Rev. 0.4 / Sep. 2006
3
1
1HY5PS561621A(L)FP
1. Description
1.1 Device Features & Ordering Information
1.1.1 Key Features
• VDD ,VDDQ =1.8 +/- 0.1V
• All inputs and outputs are compatible with SSTL_18 interface
• Fully differential clock inputs (CK, /CK) operation
• Double data rate interface
• Source synchronous-data transaction aligned to bidirectional data strobe (DQS, DQS)
• Differential Data Strobe (DQS, DQS)
• Data outputs on DQS, DQS edges when read (edged DQ)
• Data inputs on DQS centers when write(centered DQ)
• On chip DLL align DQ, DQS and DQS transition with CK transition
• DM mask write data-in at the both rising and falling edges of the data strobe
• All addresses and control inputs except data, data strobes and data masks latched on the rising edges of the
clock
• Programmable CAS latency 3, 4, 5 and 6 supported
• Programmable additive latency 0, 1, 2, 3, 4 and 5 supported
• Programmable burst length 4 / 8 with both nibble sequential and interleave mode
• Internal four bank operations with single pulsed RAS
• Auto refresh and self refresh supported
• tRAS lockout supported
• 8K refresh cycles /64ms
• JEDEC standard 84ball FBGA(x16)
• Full strength driver option controlled by EMRS
• On Die Termination supported
• Off Chip Driver Impedance Adjustment supported
• Self-Refresh High Temperature Entry
• Partial Array Self Refresh support
Ordering Information
Operating Frequency
Part No.
Organization
Package
Speed Bin
tCK(ns)
CL
tRCD
tRP
Unit
HY5PS561621A(L)FP-X*
16Mx16
Lead free**
E3
5
3
3
3
Clk
C4
3.75
4
4
4
Clk
Y5
3
5
5
5
Clk
S5
2.5
5
5
5
Clk
Note:
1. -X* is the speed bin, refer to the Operation Frequency table for
complete Part No.
2. Hynix Lead-free products are compliant to RoHS.
Rev. 0.4 / Sep. 2006
4
1
1HY5PS561621A(L)FP
1.2 Pin Configuration & Address Table
16Mx16 DDR2 PIN CONFIGURATION(Top view: see balls through package)
7
8
9
A
VSSQ
UDQS
VDDQ
UDM
B
UDQS
VSSQ
DQ15
DQ9
VDDQ
C
VDDQ
DQ8
VDDQ
DQ12
VSSQ
DQ11
D
DQ10
VSSQ
DQ13
VDD
NC
VSS
E
VSSQ
LDQS
VDDQ
DQ6
VSSQ
LDM
F
LDQS
VSSQ
DQ7
VDDQ
DQ1
VDDQ
G
VDDQ
DQ0
VDDQ
DQ4
VSSQ
DQ3
H
DQ2
VSSQ
DQ5
VDDL
VREF
VSS
J
VSSDL
CK
VDD
CKE
WE
K
RAS
CK
ODT
BA0
BA1
L
CAS
CS
A10
A1
M
A2
A0
A3
A5
N
A6
A4
A7
A9
P
A11
A8
A12
NC
R
NC
NC
1
2
3
VDD
NC
VSS
DQ14
VSSQ
VDDQ
NC
VSS
VDD
VDD
VSS
ROW AND COLUMN ADDRESS TABLE
Rev. 0.4 / Sep. 2006
ITEMS
16Mx16
# of Bank
4
Bank Address
BA0, BA1
Auto Precharge Flag
A10/AP
Row Address
A0 - A12
Column Address
A0-A8
Page size
1 KB
5
1
1HY5PS561621A(L)FP
1.3 PIN DESCRIPTION
PIN
TYPE
CK, CK
Input
DESCRIPTION
Clock: CK and CK are differential clock inputs. All address and control input signals are sampled
on the crossing of the positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK (both directions of crossing).
Clock Enable: CKE HIGH activates, and CKE LOW deactivates internal clock signals, and device
input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER DOWN and
SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN (row ACTIVE in any bank).
CKE is synchronous for POWER DOWN entry and exit, and for SELF REFRESH entry. CKE is asyn-
CKE
Input
chronous for SELF REFRESH exit. After VREF has become stable during the power on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper
self-refresh entry and exit, VREF must be maintained to this input. CKE must be maintained high
throughout READ and WRITE accesses. Input buffers, excluding CK, CK and CKE are disabled
during POWER DOWN. Input buffers, excluding CKE are disabled during SELF REFRESH.
CS
Input
Chip Select : All commands are masked when CS is registered HIGH. CS provides for external
bank selection on systems with multiple banks. CS is considered part of the command code.
On Die Termination Control : ODT(registered HIGH) enables on die termination resistance internal to the DDR2 SDRAM. When enabled, ODT is only applied to DQ, DQS, DQS, RDQS, RDQS,
ODT
Input
and DM signal for x4,x8 configurations. For x16 configuration ODT is applied to each DQ, UDQS/
UDQS.LDQS/LDQS, UDM and LDM signal. The ODT pin will be ignored if the Extended Mode
Register(EMRS(1)) is programmed to disable ODT.
RAS, CAS, WE
Input
Command Inputs: RAS, CAS and WE (along with CS) define the command being entered.
Input Data Mask : DM is an input mask signal for write data. Input Data is masked when DM is
DM
(LDM, UDM)
Input
sampled High coincident with that input data during a WRITE access. DM is sampled on both
edges of DQS, Although DM pins are input only, the DM loading matches the DQ and DQS loading. For x8 device, the function of DM or RDQS/ RDQS is enabled by EMRS command.
Bank Address Inputs: BA0 - BA2 define to which bank an ACTIVE, Read, Write or PRECHARGE
BA0 - BA2
Input
command is being applied(For 256Mb and 512Mb, BA2 is not applied). Bank address also determines if the mode register or extended mode register is to be accessed during a MRS or EMRS
cycle.
Address Inputs: Provide the row address for ACTIVE commands, and the column address and
AUTO PRECHARGE bit for READ/WRITE commands to select one location out of the memory
A0 -A15
Input
array in the respective bank. A10 is sampled during a precharge command to determine
whether the PRECHARGE applies to one bank (A10 LOW) or all banks (A10 HIGH). If only one
bank is to be precharged, the bank is selected by BA0-BA2. The address inputs also provide the
op code during MODE REGISTER SET commands.
DQ
Rev. 0.4 / Sep. 2006
Input/
Output
Data input / output : Bi-directional data bus
6
1
1HY5PS561621A(L)FP
PIN
TYPE
DESCRIPTION
Data Strobe : Output with read data, input with write data. Edge aligned with read data, centered in write data. For the x16, LDQS correspond to the data on DQ0~DQ7; UDQS corresponds
to the data on DQ8~DQ15. For the x8, an RDQS option using DM pin can be enabled via the
EMRS(1) to simplify read timing. The data strobes DQS, LDQS, UDQS, and RDQS may be used in
single ended mode or paired with optional complementary signals DQS, LDQS,UDQS and RDQS
to provide differential pair signaling to the system during both reads and wirtes. An EMRS(1)
DQS, (DQS)
(UDQS),(UDQS)
Input/
(LDQS),(LDQS)
Output
(RDQS),(RDQS)
control bit enables or disables all complementary data strobe signals.
In this data sheet, "differential DQS signals" refers to any of the following with A10 = 0 of
EMRS(1)
x16 LDQS/LDQS and UDQS/UDQS
"single-ended DQS signals" refers to any of the following with A10 = 1 of
EMRS(1)
x16 LDQS and UDQS
No Connect : No internal electrical connection is present.
NC
VDDQ
Supply
DQ Power Supply: 1.8V +/- 0.1V
VSSQ
Supply
DQ Ground
VDDL
Supply
DLL Power Supply : 1.8V +/- 0.1V
VSSDL
Supply
DLL Ground
VDD
Supply
Power Supply : 1.8V +/- 0.1V
VSS
Supply
Ground
VREF
Supply
Reference voltage for inputs for SSTL interface.
Rev. 0.4 / Sep. 2006
7
1
1HY5PS561621A(L)FP
2. Maximum DC Ratings
2.1 Absolute Maximum DC Ratings
Symbol
Rating
Units
Notes
Voltage on VDD pin relative to Vss
- 1.0 V ~ 2.3 V
V
1
VDDQ
Voltage on VDDQ pin relative to Vss
- 0.5 V ~ 2.3 V
V
1
VDDL
Voltage on VDDL pin relative to Vss
- 0.5 V ~ 2.3 V
V
1
Voltage on any pin relative to Vss
- 0.5 V ~ 2.3 V
V
1
-55 to +100
°C
1, 2
VDD
VIN, VOUT
TSTG
Parameter
Storage Temperature
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may
affect reliability.
2. Storage Temperature is the case surface temperature on the denter/top side of the DRAM. For the measurement conditions.
Please refer to JESD51-2 standard.
2.2 Operating Temperature Condition
Symbol
Parameter
Rating
Units
Notes
tOPER
Operating Temperature
0 to 95
°C
1,2
1. Operating Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions,
please refer to JESD51-2 standard.
2. At tOPER 85~95℃, Double refresh rate(tREFI: 3.9us) is required, and to enter the self refresh mode at this temperature range
it must be reguired an EMRS command to change iself refresh rate.
Rev. 0.4 / Sep. 2006
8
1
1HY5PS561621A(L)FP
3. AC & DC Operating Conditons
3.1 DC Operating Conditions
3.1.1 Recommended DC Operating Conditions (SSTL_1.8)
Rating
Symbol
Parameter
Min.
Typ.
Max.
Units
Notes
VDD
Supply Voltage
1.7
1.8
1.9
V
1
VDDL
Supply Voltage for DLL
1.7
1.8
1.9
V
1,2
VDDQ
Supply Voltage for Output
1.7
1.8
1.9
V
1,2
VREF
Input Reference Voltage
0.49*VDDQ
0.50*VDDQ
0.51*VDDQ
mV
3,4
Termination Voltage
VREF-0.04
VREF
VREF+0.04
V
5
VTT
1. Min. Typ. and Max. values increase by 100mV for C3(DDR2-533 3-3-3) speed option.
2. VDDQ tracks with VDD,VDDL tracks with VDD. AC parameters are measured with VDD,VDDQ and VDD.
3. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is
expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ
4. Peak to peak ac noise on VREF may not exceed +/-2% VREF (dc).
5. VTT of transmitting device must track VREF of receiving device.
3.1.2 ODT DC electrical characteristics
PARAMETER/CONDITION
SYMBOL
MIN
NOM
MAX
UNITS
NOTES
Rtt effective impedance value for EMRS(A6,A2)=0,1; 75 ohm
Rtt1(eff)
60
75
90
ohm
1
Rtt effective impedance value for EMRS(A6,A2)=1,0; 150 ohm
Rtt2(eff)
120
150
180
ohm
1
Rtt effective impedance value for EMRS(A6,A2)=1,1; 50 ohm
Rtt3(eff)
40
50
60
ohm
1
Deviation of VM with respect to VDDQ/2
delta VM
-6
+6
%
1
Note
1. Test condition for Rtt measurements
Measurement Definition for Rtt(eff): Apply VIH (ac) and VIL (ac) to test pin separately, then measure current I(VIH (ac)) and
I(VIL(ac)) respectively. VIH (ac), VIL (ac), and VDDQ values defined in SSTL_18
Rtt(eff) =
VIH (ac) - VIL (ac)
I(VIH (ac)) - I(VIL (ac))
Measurement Definition for VM : Measurement Voltage at test pin(mid point) with no load.
2 x Vm
delta VM =
Rev. 0.4 / Sep. 2006
VDDQ
-1
x 100%
9
1
1HY5PS561621A(L)FP
3.2 DC & AC Logic Input Levels
3.2.1 Input DC Logic Level
Symbol
Parameter
Min.
Max.
Units
VIH(dc)
dc input logic high
VREF + 0.125
VDDQ + 0.3
V
VIL(dc)
dc input logic low
- 0.3
VREF - 0.125
V
Notes
3.2.2 Input AC Logic Level
DDR2 400,533
Symbol
DDR2 667,800
Parameter
Units
Min.
Max.
Min.
Max.
VIH (ac)
ac input logic high
VREF + 0.250
-
VREF + 0.200
-
V
VIL (ac)
ac input logic low
-
VREF - 0.250
-
VREF - 0.200
V
Notes
3.2.3 AC Input Test Conditions
Symbol
Condition
Value
Units
Notes
VREF
Input reference voltage
0.5 * VDDQ
V
1
VSWING(MAX)
Input signal maximum peak to peak swing
1.0
V
1
SLEW
Input signal minimum slew rate
1.0
V/ns
2, 3
Note:
1. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the device
under test.
2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(ac) min for rising
edges and the range from VREF to VIL(ac) max for falling edges as shown in the below figure.
3. AC timings are referenced with input waveforms switching from VIL(ac) to VIH(ac) on the positive transitions
and VIH(ac) to VIL(ac) on the negative transitions.
VDDQ
VIH(ac) min
VIH(dc) min
VREF
VSWING(MAX)
VIL(dc) max
delta TF
Falling Slew = VREF - VIL(ac) max
delta TF
delta TR
VIL(ac) max
VSS
Rising Slew = VIH(ac) min - VREF
delta TR
< Figure : AC Input Test Signal Waveform>
Rev. 0.4 / Sep. 2006
10
1
1HY5PS561621A(L)FP
3.2.4 Differential Input AC logic Level
Symbol
Parameter
VID (ac)
ac differential input voltage
VIX (ac)
ac differential cross point voltage
Min.
Max.
Units
Notes
0.5
VDDQ + 0.6
V
1
0.5 * VDDQ - 0.175
0.5 * VDDQ + 0.175
V
2
1. VIN(DC) specifies the allowable DC execution of each input of differential pair such as CK, CK, DQS, DQS, LDQS, LDQS, UDQS
and UDQS.
2. VID(DC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input (such as CK,
DQS, LDQS or UDQS) level and VCP is the complementary input (such as CK, DQS, LDQS or UDQS) level. The minimum value
is equal to VIH(DC) - V IL(DC).
VDDQ
VTR
Crossing point
VID
VIX or VOX
VCP
VSSQ
< Differential signal levels >
Note:
1. VID(AC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input signal (such as
CK, DQS, LDQS or UDQS) and VCP is the complementary input signal (such as CK, DQS, LDQS or UDQS). The minimum value
is equal to V IH(AC) - V IL(AC).
2. The typical value of VIX(AC) is expected to be about 0.5 * VDDQ of the transmitting device and VIX(AC) is expected to track
variations in VDDQ . VIX(AC) indicates the voltage at which differential input signals must cross.
3.2.5 Differential AC output parameters
Symbol
Parameter
Min.
Max.
Units
Notes
VOX (ac)
ac differential cross point voltage
0.5 * VDDQ - 0.125
0.5 * VDDQ + 0.125
V
1
Note:
1. The typical value of VOX(AC) is expected to be about 0.5 * V DDQ of the transmitting device and VOX(AC) is expected to track
variations in VDDQ . VOX(AC) indicates the voltage at whitch differential output signals must cross.
Rev. 0.4 / Sep. 2006
11
1
1HY5PS561621A(L)FP
3.3 Output Buffer Characteristics
3.3.1 Output AC Test Conditions
Symbol
VOTR
Parameter
Output Timing Measurement Reference Level
SSTL_18 Class II
Units
Notes
0.5 * VDDQ
V
1
SSTl_18
Units
Notes
- 13.4
mA
1, 3, 4
13.4
mA
2, 3, 4
1. The VDDQ of the device under test is referenced.
3.3.2 Output DC Current Drive
Symbol
1.
Parameter
IOH(dc)
Output Minimum Source DC Current
IOL(dc)
Output Minimum Sink DC Current
VDDQ = 1.7 V; VOUT = 1420 mV. (VOUT - VDDQ)/IOH must be less than 21 ohm for values of VOUT between VDDQ and VDDQ 280 mV.
2.
VDDQ = 1.7 V; VOUT = 280 mV. VOUT/IOL must be less than 21 ohm for values of VOUT between 0 V and 280 mV.
3.
The dc value of VREF applied to the receiving device is set to VTT
4.
The values of IOH(dc) and IOL(dc) are based on the conditions given in Notes 1 and 2. They are used to test device drive
current capability to ensure VIH min plus a noise margin and VIL max minus a noise margin are delivered to an SSTL_18
receiver. The actual current values are derived by shifting the desired driver operating point (see Section 3.3) along a 21 ohm
load line to define a convenient driver current for measurement.
3.3.3 OCD defalut characteristics
Description
Parameter
Min
Output impedance
-
Output impedance step size for OCD calibration
Pull-up and pull-down mismatch
Output slew rate
Rev. 0.4 / Sep. 2006
Sout
Nom
Unit
Notes
-
ohms
1
0
1.5
ohms
6
0
4
ohms
1,2,3
5
V/ns
1,4,5,6,7,8
1.5
-
Max
-
12
1
1HY5PS561621A(L)FP
Note
1. Absolute Specifications ( Toper; VDD = +1.8V ±0.1V, VDDQ = +1.8V ±0.1V)
2. Impedance measurement condition for output source dc current: VDDQ=1.7V; VOUT=1420mV; (VOUT-VDDQ)/Ioh must be
less than 23.4 ohms for values of VOUT between VDDQ and VDDQ-280mV. Impedance measurement condition for output sink
dc current: VDDQ = 1.7V; VOUT = 280mV; VOUT/Iol must be less than 23.4 ohms for values of VOUT between 0V and 280mV.
3. Mismatch is absolute value between pull-up and pull-dn, both are measured at same temperature and voltage.
4. Slew rate measured from vil(ac) to vih(ac).
5. The absolute value of the slew rate as measured from DC to DC is equal to or greater than the slew rate as measured from AC
to AC. This is guaranteed by design and characterization.
6. This represents the step size when the OCD is near 18 ohms at nominal conditions across all process corners/variations and
represents only the DRAM uncertainty. A 0 ohm value(no calibration) can only be achieved if the OCD impedance is 18 ohms
+/- 0.75 ohms under nominal conditions.
Output Slew rate load:
VTT
25 ohms
Output
(Vout)
Reference
point
7. DRAM output slew rate specification applies to 400 , 533 and 667 MT/s speed bins.
8. Timing skew due to DRAM output slew rate mis-match between DQS / DQS and associated DQs is included in tDQSQ and
tQHS specification.
Rev. 0.4 / Sep. 2006
13
1
1HY5PS561621A(L)FP
3.4 IDD Specifications & Test Conditions
IDD Specifications(x16) (TCASE : 0 to 95oC)
Symbol
DDR2 800
@CL5
DDR2 667
@CL5
DDR2 533
@CL4
DDR2 400
@CL3
Units
IDD0
85
80
75
70
mA
IDD1
105
100
90
80
mA
IDD2P
8
8
7
6
mA
IDD2Q
40
35
30
25
mA
IDD2N
45
40
35
30
mA
IDD3P(F)
35
35
30
30
mA
IDD3P(S)
35
35
30
30
mA
IDD3N
60
55
50
45
mA
IDD4W
200
180
160
140
mA
IDD4R
190
150
130
120
mA
IDD5B
120
120
115
110
mA
IDD6(Normal)
4
4
4
4
mA
1
IDD6(Low)
2
2
2
2
mA
1
IDD7
230
220
210
200
mA
Note
Notes :
1. IDD6 current alues are guaranted up to Tcase of 85oC max.
Rev. 0.4 / Sep. 2006
14
1
1HY5PS561621A(L)FP
IDD Test Conditions
(IDD values are for full operating range of Voltage and Temperature, Notes 1-5)
Symbol
Conditions
Units
IDD0
Operating one bank active-precharge current; tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRAS min(IDD)
; CKE is HIGH, CS is HIGH between valid commands;Address bus inputs are SWITCHING;Data bus
inputs are SWITCHING
mA
IDD1
Operating one bank active-read-precharge curren ; IOUT = 0mA;BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD = tRCD(IDD) ; CKE is HIGH, CS is HIGH
between valid commands ; Address bus inputs are SWITCHING ; Data pattern is same as IDD4W
mA
IDD2P
Precharge power-down current ; All banks idle ; tCK = tCK(IDD) ; CKE is LOW ; Other control and
address bus inputs are STABLE; Data bus inputs are FLOATING
mA
IDD2Q
Precharge quiet standby current;All banks idle; tCK = tCK(IDD);CKE is HIGH, CS is HIGH; Other control
and address bus inputs are STABLE; Data bus inputs are FLOATING
mA
IDD2N
Precharge standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH, CS is HIGH; Other control and
address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD3P
Active power-down current; All banks open; tCK = tCK(IDD); CKE is
LOW; Other control and address bus inputs are STABLE; Data bus
inputs are FLOATING
Fast PDN Exit MRS(12) = 0
mA
Slow PDN Exit MRS(12) = 1
mA
IDD3N
Active standby current; All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP =tRP(IDD); CKE is
HIGH, CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data
bus inputs are SWITCHING
mA
IDD4W
Operating burst write current; All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING
mA
IDD4R
Operating burst read current; All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL =
CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH
between valid commands; Address bus inputs are SWITCHING;; Data pattern is same as IDD4W
mA
IDD5B
Burst refresh current; tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS
is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs
are SWITCHING
mA
IDD6
Self refresh current; CK and CK at 0V; CKE ≤ 0.2V; Other control and address bus inputs are FLOATING;
Data bus inputs are FLOATING
mA
IDD7
Operating bank interleave read current; All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD),
AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC = tRC(IDD), tRRD = tRRD(IDD), tRCD = 1*tCK(IDD);
CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are STABLE during DESELECTs;
Data pattern is same as IDD4R; - Refer to the following page for detailed timing conditions
mA
Note:
1. VDDQ = 1.8 +/- 0.1V ; VDD = 1.8 +/- 0.1V (exclusively VDDQ = 1.9 +/- 0.1V ; VDD = 1.9 +/- 0.1V for C3 speed grade)
2. IDD specifications are tested after the device is properly initialized
3. Input slew rate is specified by AC Parametric Test Condition
4. IDD parameters are specified with ODT disabled.
5. Data bus consists of DQ, DM, DQS, DQS, RDQS, RDQS, LDQS, LDQS, UDQS, and UDQS. IDD values must be met with all
combinations of EMRS bits 10 and 11.
6. Definitions for IDD
LOW is defined as Vin ≤ VILAC(max)
HIGH is defined as Vin ≥ VIHAC(min)
STABLE is defined as inputs stable at a HIGH or LOW level
FLOATING is defined as inputs at VREF = VDDQ/2
SWITCHING is defined as: inputs changing between HIGH and LOW every other clock cycle (once per two clocks) for
address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per clock) for DQ
signals not including masks or strobes.
Rev. 0.4 / Sep. 2006
15
1
1HY5PS561621A(L)FP
For purposes of IDD testing, the following parameters are to be utilized
Speed
Bin
(CL-tRCD-tRP)
5-5-5
6-6-6
4-4-4
5-5-5
3-3-3
4-4-4
3-3-3
CL(IDD)
5
6
4
5
3
4
3
tCK
tRCD(IDD)
12.5
15
12
15
11.25
15
15
ns
tRC(IDD)
57.25
60
57
60
56.25
60
55
ns
tRRD(IDD)-x4/x8
7.5
7.5
7.5
7.5
7.5
7.5
7.5
ns
tRRD(IDD)-x16
10
10
10
10
10
10
10
ns
tCK(IDD)
2.5
2.5
3
3
3.75
3.75
5
ns
tRASmin(IDD)
45
45
45
45
45
45
40
ns
tRASmax(IDD)
70000
70000
70000
70000
70000
70000
70000
ns
tRP(IDD)
12.5
15
12
15
11.25
15
15
ns
tRFC(IDD)-256Mb
75
75
75
75
75
75
75
ns
tRFC(IDD)-512Mb
105
105
105
105
105
105
105
ns
tRFC(IDD)-1Gb
127.5
127.5
127.5
127.5
127.5
127.5
127.5
ns
DDR2-800
DDR2-667
DDR2-533
DDR2-400
Units
Detailed IDD7
The detailed timings are shown below for IDD7. Changes will be required if timing parameter changes are made to the specification.
Legend: A = Active; RA = Read with Autoprecharge; D = Deselect
IDD7: Operating Current: All Bank Interleave Read operation
All banks are being interleaved at minimum tRC(IDD) without violating tRRD(IDD) using a burst length of 4. Control and address bus
inputs are STABLE during DESELECTs. IOUT = 0mA
Timing Patterns for 4 bank devices x4/ x8/ x16
-DDR2-400 3/3/3: A0 RA0 A1 RA1 A2 RA2 A3 RA3 D D D (11 clocks)
-DDR2-533 3/3/3: A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D D (15 clocks)
-DDR2-533 4/4/4: A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D D D (16 clocks)
-DDR2-667 4/4/4: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D (19 clocks)
-DDR2-667 5/5/5: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D D (20 clocks)
Rev. 0.4 / Sep. 2006
16
1
1HY5PS561621A(L)FP
3.5. Input/Output Capacitance
Parameter
Symbol
DDR2- 400
DDR2- 533
DDR2 667
DDR2 800
Units
Min
Max
Min
Max
Min
Max
CCK
1.0
2.0
1.0
2.0
1.0
2.0
pF
CDCK
x
0.25
x
0.25
x
0.25
pF
CI
1.0
2.0
1.0
2.0
1.0
1.75
pF
Input capacitance delta, all other input-only pins
CDI
x
0.25
x
0.25
x
0.25
pF
Input/output capacitance, DQ, DM, DQS, DQS
CIO
2.5
4.0
2.5
3.5
2.5
3.5
pF
CDIO
x
0.5
x
0.5
x
0.5
pF
Input capacitance, CK and CK
Input capacitance delta, CK and CK
Input capacitance, all other input-only pins
Input/output capacitance delta, DQ, DM, DQS, DQS
4. Electrical Characteristics & AC Timing Specification
( 0 ℃ ≤ TCASE ≤ 95℃; VDDQ = 1.8 V +/- 0.1V; VDD = 1.8V +/- 0.1V)
Refresh Parameters
Parameter
Refresh to Active/Refresh command time
Symbol
Spec
Units
tRFC
75
ns
0 ℃≤ TCASE ≤ 85℃
7.8
ns
85℃ < TCASE ≤ 95℃
3.9
ns
tREFI
Average periodic refresh interval
DDR2 SDRAM speed bins and tRCD, tRP and tRC for corresponding bin
Speed
DDR2-800
DDR2-667
DDR2-533
DDR2-400
Bin(CL-tRCD-tRP)
5-5-5
5-5-5
4-4-4
3-3-3
Parameter
min
min
min
min
CAS Latency
5
5
4
5
tCK
tRCD
12.5
15
15
15
ns
tRP
12.5
15
15
15
ns
tRAS
45
45
45
40
ns
tRC
57.25
60
60
55
ns
Rev. 0.4 / Sep. 2006
Units
17
1
1HY5PS561621A(L)FP
Timing Parameters by Speed Grade
(Refer to notes for information related to this table at the following pages of this table)
Parameter
DDR2-400
Symbol
DDR2-533
Unit
min
max
min
max
Note
DQ output access time from CK/CK
tAC
-600
+600
-500
+500
ps
DQS output access time from CK/CK
tDQSCK
-500
+500
-450
+450
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min(tCL,tCH)
-
min(tCL,tCH)
-
ps
Clock cycle time, CL=x
tCK
5000
8000
3750
8000
ps
15
DQ and DM input setup time(differential strobe)
tDS(base)
150
-
100
-
ps
6,7,8,20
DQ and DM input hold time(differential strobe)
tDH(base)
275
-
225
-
ps
6,7,8,21
DQ and DM input setup time(single ended strobe)
tDS
25
-
-25
-
ps
6,7,8,20
DQ and DM input hold time(single ended strobe)
tDH
25
-
-25
-
ps
6,7,8,21
Control & Address input pulse width for each input
tIPW
0.6
-
0.6
-
tCK
DQ and DM input pulse width for each input
tDIPW
0.35
-
0.35
-
tCK
Data-out high-impedance time from CK/CK
tHZ
-
tAC max
-
tAC max
ps
18
DQS low-impedance time from CK/CK
tLZ(DQS)
tAC min
tAC max
tAC min
tAC max
ps
18
DQ low-impedance time from CK/CK
tLZ(DQ)
2*tAC min
tAC max
2*tAC min
tAC max
ps
18
DQS-DQ skew for DQS and associated DQ signals
tDQSQ
-
350
-
300
ps
13
DQ hold skew factor
tQHS
-
450
-
400
ps
12
DQ/DQS output hold time from DQS
tQH
tHP - tQHS
-
tHP - tQHS
-
ps
First DQS latching transition to associated clock
edge
tDQSS
-0.25
+ 0.25
-0.25
+ 0.25
tCK
DQS input high pulse width
tDQSH
0.35
-
0.35
-
tCK
DQS input low pulse width
tDQSL
0.35
-
0.35
-
tCK
DQS falling edge to CK setup time
tDSS
0.2
-
0.2
-
tCK
DQS falling edge hold time from CK
tDSH
0.2
-
0.2
-
tCK
Mode register set command cycle time
tMRD
2
-
2
-
tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35
-
0.35
-
tCK
Address and control input setup time
tIS(base)
350
-
250
-
ps
5,7,9,23
Address and control input hold time
tIH(base)
475
-
375
-
ps
5,7,9,23
Read preamble
tRPRE
0.9
1.1
0.9
1.1
tCK
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
Active to active command period
tRRD
7.5
-
7.5
-
ns
Four Activate Window
tFAW
37.5
-
37.5
-
ns
CAS to CAS command delay
tCCD
2
Write recovery time
tWR
15
-
15
-
ns
Auto precharge write recovery + precharge time
tDAL
WR+tRP
-
WR+tRP
-
tCK
14
Internal write to read command delay
tWTR
10
-
7.5
-
ns
24
Internal read to precharge command delay
tRTP
7.5
ns
3
Rev. 0.4 / Sep. 2006
2
7.5
11,12
10
4
tCK
18
1
1HY5PS561621A(L)FP
-ContinueParameter
DDR2-400
Symbol
min
DDR2-533
max
min
Unit
Note
max
Exit self refresh to a non-read command
tXSNR
tRFC + 10
Exit self refresh to a read command
tXSRD
200
-
200
-
tCK
Exit precharge power down to any non-read
command
tXP
2
-
2
-
tCK
Exit active power down to read command
tXARD
2
2
tCK
1
Exit active power down to read command
(Slow exit, Lower power)
tXARDS
6 - AL
6 - AL
tCK
1, 2
CKE minimum pulse width
(high and low pulse width)
t
3
3
ODT turn-on delay
t
2
2
2
2
tCK
ODT turn-on
tAON
tAC(min)
tAC(max)+
1
tAC(min)
tAC(max)+
1
ns
ODT turn-on(Power-Down mode)
t
tAC(min)+2
2tCK+
tAC(max)+
1
tAC(min)+2
2tCK+
tAC(max)+
1
ns
ODT turn-off delay
t
2.5
2.5
2.5
2.5
tCK
tAC(min)
tAC(max)+
0.6
tAC(min)
tAC(max)+
0.6
ns
tAC(min)+2
2.5tCK+
tAC(max)+
1
tAC(min)+2
2.5tCK+
tAC(max)+
1
ns
CKE
AOND
AONPD
AOFD
ODT turn-off
tAOF
ODT turn-off (Power-Down mode)
t
AOFPD
tRFC + 10
ns
tCK
ODT to power down entry latency
tANPD
3
3
tCK
ODT power down exit latency
tAXPD
8
8
tCK
OCD drive mode output delay
tOIT
0
Minimum time clocks remains ON after CKE
asynchronously drops LOW
tDelay
Rev. 0.4 / Sep. 2006
tIS+tCK+tIH
12
0
tIS+tCK+tIH
12
27
16
17
ns
ns
15
19
1
1HY5PS561621A(L)FP
Parameter
DDR2-667
Symbol
DDR2-800
Unit
min
max
min
max
DQ output access time from CK/CK
tAC
-450
+450
-400
+400
DQS output access time from CK/CK
tDQSCK
-400
+400
-350
+350
ps
CK high-level width
tCH
0.45
0.55
0.45
0.55
tCK
CK low-level width
tCL
0.45
0.55
0.45
0.55
tCK
CK half period
tHP
min(tCL,
tCH)
-
min(tCL,
tCH)
-
ps
Clock cycle time, CL=x
tCK
3000
8000
2500
DQ and DM input setup time
tDS(base)
100
-
50
-
DQ and DM input hold time
tDH(base)
175
-
125
Control & Address input pulse width for each input
tIPW
0.6
-
0.6
DQ and DM input pulse width for each input
tDIPW
0.35
-
Data-out high-impedance time from CK/CK
tHZ
-
tAC max
DQS low-impedance time from CK/CK
tLZ(DQS)
tAC min
tAC max
tAC min
DQ low-impedance time from CK/CK
tLZ(DQ)
2*tAC min
tAC max
DQS-DQ skew for DQS and associated DQ signals
tDQSQ
-
240
DQ hold skew factor
tQHS
-
DQ/DQS output hold time from DQS
tQH
First DQS latching transition to associated clock edge
tDQSS
DQS input high pulse width
DQS input low pulse width
Note
ps
11,12
ps
15
ps
6,7,8,20
-
ps
6,7,8,21
-
tCK
0.35
-
tCK
-
tAC max
ps
18
tAC max
ps
18
2*tAC min
tAC max
ps
18
-
200
ps
13
340
-
300
ps
12
tHP - tQHS
-
tHP - tQHS
-
ps
- 0.25
+ 0.25
- 0.25
+ 0.25
tCK
tDQSH
0.35
-
0.35
-
tCK
tDQSL
0.35
-
0.35
-
tCK
DQS falling edge to CK setup time
tDSS
0.2
-
0.2
-
tCK
DQS falling edge hold time from CK
tDSH
0.2
-
0.2
-
tCK
Mode register set command cycle time
tMRD
2
-
2
-
tCK
Write postamble
tWPST
0.4
0.6
0.4
0.6
tCK
Write preamble
tWPRE
0.35
-
0.35
-
tCK
Address and control input setup time
tIS(base)
200
-
175
-
ps
5,7,9,22
Address and control input hold time
tIH(base)
275
-
250
-
ps
5,7,9,23
Read preamble
tRPRE
0.9
1.1
0.9
1.1
tCK
19
Read postamble
tRPST
0.4
0.6
0.4
0.6
tCK
19
Activate to precharge command
tRAS
45
70000
45
70000
ns
3
Active to active command period for 1KB page size
products
tRRD
7.5
-
7.5
-
ns
4
Four Activate Window
tFAW
37.5
-
37.5
-
ns
CAS to CAS command delay
tCCD
2
Write recovery time
tWR
15
-
15
-
ns
Auto precharge write recovery + precharge time
tDAL
WR+tRP
-
WR+tRP
-
tCK
Internal write to read command delay
tWTR
7.5
-
7.5
-
ns
Internal read to precharge command delay
tRTP
7.5
Exit self refresh to a non-read command
tXSNR
tRFC + 10
Exit self refresh to a read command
tXSRD
200
-
200
-
tCK
2
-
2
-
tCK
Exit precharge power down to any non-read command tXP
Rev. 0.4 / Sep. 2006
2
10
tCK
7.5
ns
tRFC + 10
14
3
ns
20
1
1HY5PS561621A(L)FP
-ContinueSymbol
Parameter
Exit active power down to read command
Exit active power down to read command
(Slow exit, Lower power)
CKE minimum pulse width
(high and low pulse width)
ODT turn-on delay
DDR2-667
min
DDR2-800
max
min
max
Unit
Note
tXARD
2
2
tCK
1
tXARDS
7 - AL
8 - AL
tCK
1, 2
t
3
3
tCK
t
2
2
2
2
tCK
tAC(min)
tAC(max)
+0.7
ns
2tCK+
tAC(max)+1
ns
CKE
AOND
ODT turn-on
t
tAC(min)
tAC(max)
+0.7
ODT turn-on(Power-Down mode)
t
tAC(min)+2
2tCK+
tAC(max)+1
tAC(min)
+2
ODT turn-off delay
t
2.5
2.5
2.5
2.5
tCK
tAC(min)
tAC(max)
+0.6
ns
tAC(min)
+2
2.5tCK+
tAC(max)+1
ns
AON
AONPD
AOFD
ODT turn-off
tAOF
tAC(min)
tAC(max)+
0.6
ODT turn-off (Power-Down mode)
tAOFPD
tAC(min)
+2
2.5tCK+
tAC(max)+1
ODT to power down entry latency
tANPD
3
3
tCK
ODT power down exit latency
tAXPD
8
8
tCK
OCD drive mode output delay
tOIT
0
Minimum time clocks remains ON after CKE
asynchronously drops LOW
Rev. 0.4 / Sep. 2006
tDelay
tIS+tCK+tIH
12
0
tIS+tCK
+tIH
12
6,16
17
ns
ns
15
21
1
1HY5PS561621A(L)FP
General notes, which may apply for all AC parameters
1. Slew Rate Measurement Levels
a. Output slew rate for falling and rising edges is measured between VTT - 250 mV and VTT + 250 mV for single ended signals.
For differential signals (e.g. DQS - DQS) output slew rate is measured between DQS - DQS = -500 mV and DQS - DQS = +500mV.
Output slew rate is guaranteed by design, but is not necessarily tested on each device.
b. Input slew rate for single ended signals is measured from dc-level to ac-level: from VIL(dc) to VIH(ac) for rising edges and from
VIH(dc) and VIL(ac) for falling edges.
For differential signals (e.g. CK - CK) slew rate for rising edges is measured from CK - CK = -250 mV to CK - CK = +500 mV(250mV
to -500 mV for falling egdes).
c. VID is the magnitude of the difference between the input voltage on CK and the input voltage on CK, or between DQS and DQS for
differential strobe.
2. DDR2 SDRAM AC timing reference load
The following figure represents the timing reference load used in defining the relevant timing parameters of the part. It is not
intended to be either a precise representation of the typical system environment nor a depiction of the actual load presented by a
production tester. System designers will use IBIS or other simulation tools to correlate the timing reference load to a system environment. Manufacturers will correlate to their production test conditions (generally a coaxial transmission line terminated at the tester
electronics).
VDDQ
DUT
DQ
DQS
DQS
RDQS
RDQS
Output
VTT = VDDQ/2
Timing
reference
point
25Ω
AC Timing Reference Load
The output timing reference voltage level for single ended signals is the crosspoint with VTT. The output timing reference voltage
level for differential signals is the crosspoint of the true (e.g. DQS) and the complement (e.g. DQS) signal.
3. DDR2 SDRAM output slew rate test load
Output slew rate is characterized under the test conditions as shown below.
VDDQ
DUT
DQ
DQS, DQS
RDQS, RDQS
Output
Test point
VTT = VDDQ/2
25Ω
Slew Rate Test Load
4. Differential data strobe
DDR2 SDRAM pin timings are specified for either single ended mode or differential mode depending on the setting of the EMRS
“Enable DQS” mode bit; timing advantages of differential mode are realized in system design. The method by which the DDR2
SDRAM pin timings are measured is mode dependent. In single
Rev. 0.4 / Sep. 2006
22
1
1HY5PS561621A(L)FP
VREF. In differential mode, these timing relationships are measured relative to the crosspoint of DQS and its complement, DQS. This
distinction in timing methods is guaranteed by design and characterization. Note that when differential data strobe mode is disabled
via the EMRS, the complementary pin, DQS, must be tied externally to VSS through a 20 ohm to 10 K ohm resistor to insure proper
operation.
tDQSH
DQS
DQS/
DQS
tDQSL
DQS
tWPRE
tWPST
VIH(dc)
VIH(ac)
DQ
D
D
VIL(dc)
tDS
VIH(ac)
tDS
DM
D
D
VIL(ac)
DMin
DMin
tDH
DMin
tDH
VIH(dc)
DMin
VIL(ac)
VIL(dc)
Figure -- Data input (write) timing
tCH
tCL
CK
CK/CK
CK
DQS
DQS/DQS
DQS
tRPST
tRPRE
DQ
Q
Q
tDQSQmax
Q
Q
tDQSQmax
tQH
tQH
Figure -- Data output (read) timing
5. AC timings are for linear signal transitions. See System Derating for other signal transitions.
6. These parameters guarantee device behavior, but they are not necessarily tested on each device.
They may be guaranteed by device design or tester correlation.
7. All voltages referenced to VSS.
8. Tests for AC timing, IDD, and electrical (AC and DC) characteristics, may be conducted at nominal reference/
supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage
range specified.
Rev. 0.4 / Sep. 2006
23
1
1HY5PS561621A(L)FP
Specific Notes for dedicated AC parameters
1. User can choose which active power down exit timing to use via MRS(bit 12). tXARD is expected to be used for fast active
power down exit timing. tXARDS is expected to be used for slow active power down exit timing where a lower power value is
defined by each vendor data sheet.
2. AL = Additive Latency
3. This is a minimum requirement. Minimum read to precharge timing is AL + BL/2 providing the tRTP and tRAS(min) have been
satisfied.
4. A minimum of two clocks (2 * tCK) is required irrespective of operating frequency
5. Timings are guaranteed with command/address input slew rate of 1.0 V/ns. See System Derating for other slew rate values.
6. Timings are guaranteed with data, mask, and (DQS/RDQS in singled ended mode) input slew rate of 1.0 V/ns. See System
Derating for other slew rate values.
7. Timings are guaranteed with CK/CK differential slew rate of 2.0 V/ns. Timings are guaranteed for DQS signals with a
differen tial slew rate of 2.0 V/ns in differential strobe mode and a slew rate of 1V/ns in single ended mode. See System
Derating for other slew rate values.
8. tDS and tDH derating
table
DDR2- 400
/ 533)
tDS,
tDH(for
Derating
Values(ALL
units in 'ps', Note 1 applies to entire Table)
DQS, DQS Differential Slew Rate
4.0 V/ns
2.0
DQ
Slew
rate
V/ns
3.0 V/ns
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
1.2 V/ns
1.0 V/ns
0.8 V/ns
△ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD △ tD
S
H
S
H
S
H
S
H
S
H
S
H
S
H
S
H
S
H
125 45 125 45 +125 +45
-
1.5
1.0
83
21
83
21
+83
+21
95
33
0
0
0
0
0.9
-
-
-11
-14
0.8
0.7
-
-
-
-
-
-
-
-
0.6
-
-
-
-
0.5
0.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0
0
12
12
24
24
-
-
-
-
-
-
-
-
-11
-14
1
-2
13
10
25
22
-
-
-
-
-
-
-25
-31
-13
-19
-1
-7
11
5
23
17
-
-
-
-
-
-
-31
-42
-42
-19
-7
-8
5
-6
17
6
-
-
-
-
-
-
-43
-59
-31
-47
-19
-35
-7
-23
5
-11
-
-
-74
-89
-62
-77
-50
-65
-38
-53
-
-
-
-
-127 -140 -115 -128 -103 -116
1) For all input signals the total tDS(setup time) and tDH(hold time) required is calculated by adding the datasheet value to the derating
value listed in above Table.
Setup(tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing
of Vih(ac)min. Setup(tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(dc) and
the first crossing of Vil(ac)max. If the actual signal is always earlier than the nominal slew rate line between shaded ‘ VREF(dc) to ac
region’, use nominal slew rate for derating value(see Fig a.) If the actual signal is later than the nominal slew rate line anywhere
between shaded ‘VREF(dc) to ac region’, the slew rate of a tangent line to the actual signal from the ac level to dc level is used for
derating value(see Fig b.)
Hold(tDH) nominal slew rate for a rising signal is defined as the slew rate rate between the last crossing of Vil(dc) max and the first
crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of Vih(dc)
min and the first crossing of VREF(dc). If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘dc to
VREF(dc) region’, the slew rate of a tangent line to the actual signal from the dc level to VREF(dc) level is used for derating value(see
Fig d.)
Although for slow slew rates the total setup time might be negative(i.e. a valid input signal will not have reached VIH/IL(ac) at the
Rev. 0.4 / Sep. 2006
24
1
1HY5PS561621A(L)FP
time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
For slew rate in between the values listed in table x, the derating valued may obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
Hold(tDH) nominal slew rate for a rising signal is defined as the slew rate rate between the last crossing of Vil(dc) max and the first
crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of Vih(dc)
min and the first crossing of VREF(dc). If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘dc to
VREF(dc) region’, the slew rate of a tangent line to the actual signal from the dc level to VREF(dc) level is used for derating value(see
Fig d.)
Although for slow slew rates the total setup time might be negative(i.e. a valid input signal will not have reached VIH/IL(ac) at the
time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
For slew rate in between the values listed in table x, the derating valued may obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
Rev. 0.4 / Sep. 2006
25
1
1HY5PS561621A(L)FP
Fig. a Illustration of nominal slew rate for tIS,tDS
CK,DQS
CK, DQS
tIS,
tDS
tIH,
tDH
tIS,
tDS
tIH,
tDH
VDDQ
VIH(ac)min
VIH(dc)min
nominal
slew rate
VREF(dc)
nominal
slew rate
VIL(dc)max
VREF to ac
region
VIL(ac)max
Vss
Delta TF
Setup Slew Rate
=
Falling Signal
Rev. 0.4 / Sep. 2006
VREF(dc)-VIL(ac)max
Delta TF
Delta TR
Setup Slew Rate
=
Rising Signal
VIH(ac)min-VREF(dc)
Delta TR
26
1
1HY5PS561621A(L)FP
Fig. -b Illustration of tangent line for tIS,tDS
CK, DQS
CK, DQS
tIS,
tDS
tIH,
tDH
tIS,
tDS
tIH,
tDH
VDDQ
nominal
line
VIH(ac)min
VIH(dc)min
tangent
line
VREF(dc)
Tangent
line
VIL(dc)max
VREF to ac
region
VIL(ac)max
Nomial
line
Vss
Delta TR
Delta TF
Setup Slew Rate Tangent line[VIH(ac)min-VREF(dc)]
=
Rising Signal
Delta TR
Setup Slew Rate Tangent line[VREF(dc)-VIL(ac)max]
=
Falling Signal
Delta TF
Rev. 0.4 / Sep. 2006
27
1
1HY5PS561621A(L)FP
Fig. -c Illustration of nominal line for tIH, tDH
CK, DQS
CK, DQS
tIS,
tDS
tIH,
tDH
tIS,
tDS
tIH,
tDH
VDDQ
VIH(ac)min
VIH(dc)min
dc to VREF
region
VREF(dc)
nominal
slew rate
nominal
slew rate
VIL(dc)max
VIL(ac)max
Vss
Delta TR
Hold Slew Rate
=
Rising Signal
Rev. 0.4 / Sep. 2006
VREF(dc)-VIL(dc)max
Delta TR
Delta TF
VIH(dc)min - VREF(dc)
Hold Slew Rate
=
Falling Signal
Delta TF
28
1
1HY5PS561621A(L)FP
Fig. -d Illustration of tangent line for tIH , tDH
CK, DQS
CK, DQS
tIS,
tDS
tIH,
tDH
tIS,
tDS
tIH,
tDH
VDDQ
VIH(ac)min
nominal
line
VIH(dc)min
tangent
line
VREF(dc)
dc to VREF
region
Tangent
line
nominal
line
VIL(dc)max
VIL(ac)max
Vss
Delta TR
Delta TF
Hold Slew Rate Tangent line[VREF(dc)-VIL(ac)max]
=
Rising Signal
Delta TR
Tangent line[VIH(ac)min-VREF(dc)]
Hold Slew Rate
=
Falling Signal
Delta TF
Rev. 0.4 / Sep. 2006
29
1
1HY5PS561621A(L)FP
9. tIS and tIH (input setup and hold) derating
tIS, tIH Derating Values for DDR2 400, DDR2 533
CK, CK Differential Slew Rate
2.0 V/ns
Command /
Address Slew
rate(V/ns)
1.5 V/ns
1.0 V/ns
△tIS
△tIH
△tIS
△tIH
△tIS
△tIH
4.0
+187
+94
+217
+124
+247
+124
ps
1
3.5
+179
+89
+209
+119
+239
+149
ps
1
3.0
+167
+83
+197
+113
+227
+143
ps
1
2.5
+150
+75
+180
+105
+210
+135
ps
1
2.0
+125
+45
+155
+75
+185
+105
ps
1
1.5
+83
+21
+113
+51
+143
+81
ps
1
1.0
+0
0
+30
+30
+60
60
ps
1
0.9
-11
-14
+19
+16
+49
+46
ps
1
Units Notes
0.8
-25
-31
+5
-1
+35
+29
ps
1
0.7
-43
-54
-37
-53
-7
+6
ps
1
0.6
-67
-83
-37
-53
-7
-23
ps
1
0.5
-100
-125
-80
-95
-50
-65
ps
1
0.4
-150
-188
-145
-158
-115
-128
ps
1
0.3
-223
-292
-255
-262
-225
-232
ps
1
0.25
-250
-375
-320
-345
-290
-315
ps
1
0.2
-500
-500
-495
-470
-465
-440
ps
1
0.15
-750
-708
-770
-678
-740
-648
ps
1
0.1
-1250
-1125
-1420
-1095
-1065
TBD
ps
1
tIS, tIH Derating Values for DDR2 667, DDR2 800
CK, CK Differential Slew Rate
2.0 V/ns
Command /
Address Slew
rate(V/ns)
Rev. 0.4 / Sep. 2006
1.5 V/ns
1.0 V/ns
△tIS
△tIH
△tIS
△tIH
△tIS
△tIH
4.0
+150
+94
+180
+124
+210
+154
ps
1
3.5
+143
+89
+173
+119
+203
+149
ps
1
3.0
+133
+83
+163
+113
+193
+143
ps
1
2.5
+120
+75
+150
+105
+180
+135
ps
1
2.0
+100
+45
+130
+75
+160
+105
ps
1
1.5
+67
+21
+97
+51
+127
+81
ps
1
1.0
0
0
+30
+30
+60
60
ps
1
Units Notes
0.9
-5
-14
+25
+16
+55
+46
ps
1
0.8
-13
-31
+17
-1
+47
+29
ps
1
0.7
-22
-54
+8
-24
+38
+6
ps
1
0.6
-34
-83
-4
-53
-26
-23
ps
1
0.5
-60
-125
-30
-95
0
-65
ps
1
0.4
-100
-188
-70
-158
-40
-128
ps
1
0.3
-168
-292
-138
-262
-108
-232
ps
1
0.25
-200
-375
-170
-345
-140
-315
ps
1
0.2
-325
-500
-295
-470
-265
-440
ps
1
0.15
-517
-708
-487
-678
-457
-648
ps
1
0.1
-1000
-1125
-970
-1095
-940
-1065
ps
1
30
1
1HY5PS561621A(L)FP
1) For all input signals the total tIS(setup time) and tIH(hold) time) required is calculated by adding the datasheet value to the derating
value listed in above Table.
Setup(tIS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing
of VIH(ac)min. Setup(tIS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(dc) and
the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate for line between shaded ‘VREF(dc) to
ac region’, use nominal slew rate for derating value(see fig a.) If the actual signal is later than the nominal slew rate line anywhere
between shaded ‘VREF(dc) to ac region’, the slew rate of a tangent line to the actual signal from the ac level to dc level is used for derating value(see Fig b.)
Hold(tIH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first crossing of VREF(dc). Hold(tIH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(dc). If the
actual signal signal is always later than the nominal slew rate line between shaded ‘dc to VREF(dc) region’, use nominal slew rate for
derating value(see Fig.c) If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘dc to VREF(dc)
region’, the slew rate of a tangent line to the actual signal from the dc level to VREF(dc) level is used for derating value(see Fig d.)
Although for slow rates the total setup time might be negative(i.e. a valid input signal will not have reached VIH/IL(ac) at the time of
the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
For slew rates in between the values listed in table, the derating values may obtained by linear interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
10. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but
system performance (bus turnaround) will degrade accordingly.
11. MIN ( t CL, t CH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device
(i.e. this value can be greater than the minimum specification limits for t CL and t CH). For example, t CL and t CH are = 50%
of the period, less the half period jitter ( t JIT(HP)) of the clock source, and less the half period jitter due to crosstalk ( t
JIT(crosstalk)) into the clock traces.
12. t QH = t HP – t QHS, where:
tHP = minimum half clock period for any given cycle and is defined by clock high or clock low ( tCH, tCL).
tQHS accounts for:
1) The pulse duration distortion of on-chip clock circuits; and
2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition, both
of which are, separately, due to data pin skew and output pattern effects, and p-channel to n-channel variation of the
output drivers.
13. tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as
well as output slew rate mismatch between DQS/ DQS and associated DQ in any given cycle.
14. DAL = WR + RU{tRP(ns)/tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For
tRP, if the result of the division is not already an integer, round up to the next highest integer. tCK refers to the application
clock period.
Example: For DDR533 at tCK = 3.75ns with tWR programmed to 4 clocks.
tDAL = 4 + (15ns/3.75ns) clocks = 4+(4) clocks = 8 clocks.
15. The clock frequency is allowed to change during self–refresh mode or precharge power-down mode. In case of clock
frequency change during precharge power-down, a specific procedure is required as described in section 2.9.
16. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on.
ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND.
17. ODT turn off time min is when the device starts to turn off ODT resistance.
ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
18. tHZ and tLZ transitions occur in the same access time as valid data transitions. Thesed parameters are referenced to a
specific voltage level which specifies when the device output is no longer driving(tHZ), or begins driving (tLZ). Below figure
Rev. 0.4 / Sep. 2006
31
1
1HY5PS561621A(L)FP
shows a method to calculate the point when device is no longer driving (tHZ), or begins driving (tLZ) by measuring the signal
at two different voltages. The actual voltage measurement points are not critical as long as the calculation is consistenet.
19. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no
longer driving (tRPST), or begins driving (tRPRE). Below figure shows a method to calculate these points when the device is
no longer driving (tRPST), or begins driving (tRPRE). Below Figure shows a method to calculate these points when the device
is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage
measurement points are not critical as long as the calculation is consistent.
VOH + xmV
VTT + 2xmV
VOH + 2xmV
VTT + xmV
tHZ
tRPST end point
tHZ
tRPRE begin point
VOL + 1xmV
VTT -xmV
VOL + 2xmV
VTT - 2xmV
tHZ , tRPST end point = 2*T1-T2
tLZ , tRPRE begin point = 2*T1-T2
20. Input waveform timing with differential data strobe enabled MR[bit10] =0, is referenced from the input signal crossing at the
VIH(ac) level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL(ac) level
to the differential data strobe crosspoint for a falling signal applied to the device under test.
21. Input waveform timing with differential data strobe enabled MR[bit10]=0, is referenced from the input signal crossing at the
VIH(dc) level to the differential data strobe crosspoint for a rising signal and VIL(dc) to the differential data strobe crosspoint
for a falling signal applied to the device under test.
Differential Input waveform timing
DQS
DQS
tDS
tDH
tDS
tDH
VDDQ
VIH(ac)min
VIH(dc)min
VREF(dc)
VIL(dc)max
VIL(ac)max
VSS
22. Input waveform timing is referenced from the input signal crossing at the VIH(ac) level for a rising signal and VIL(ac) for a falling
signal applied to the device under test.
23. Input waveform timing is referenced from the input signal crossing at the VIL(dc) level for a rising signal and VIH(dc) for a falling
signal applied to the device under test.
Rev. 0.4 / Sep. 2006
32
1
1HY5PS561621A(L)FP
DQS
DQS
tIS
tIH
tIS
tIH
VDDQ
VIH(ac) min
VIH(dc) min
VREF(dc)
VIL(dc) max
VIL(ac) max
VSS
24. tWTR is at least two clocks (2*tCK) independent of operation frequency.
25. Input waveform timing with single-ended data strobe enabled MR[bit10] = 1, is referenced from the input signal crossing at the
VIH(ac) level to the single-ended data strobe crossing VIH/L(dc) at the start of its transition for a rising signal, and from the input signal crossing at the VIL(ac) level to the single-ended data strobe crossing VIH/L(dc) at the start of its transition for a falling signal
applied to the device under test. The DQS signal must be monotonic between VIL(dc)max and VIH(dc) min.
26. Input waveform timing with single-ended data strobe enabled MR[bit10] = 1, is referenced from the input signal crossing at the
VIH(dc) level to the single-ended data strobe crossing VIH/L(ac) at the end of its transition for a rising signal, and from the input signal crossing at the VIL(dc) level to the single-ended data strobe crossing VIH/L(ac) at the end of its transition for a falling signal
applied to the device under test. The DQS signal must be monotonic between VIL(dc) max and VIH(dc) min.
27. tCKE min of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input
level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its
valid level during the time period of tIS + 2*tCK + tIH.
Rev. 0.4 / Sep. 2006
33
1
1HY5PS561621A(L)FP
5. Package Dimensions
Package Dimension(x16)
84 Ball Fine Pitch Ball Grid Array Outline
8.00 +/- 0.10
13.00 +/- 0.10
A1 Ball Mark
1.20 Max.
L M N P
K
A B C D
E F G
H
J
0.80
0.8 x 14 = 11.2
<Top View>
R
0.34 +/- 0.05
A1 Ball Mark
0.80
1
2
3
7
8
9
84 - φ0.45 ± 0.05
0.80 x 8 = 6.40
<Bottom View>
note: all dimension units are Millimeters.
Rev. 0.4 / Sep. 2006
34