White Electronic Designs Display Systems Division ENH104V1-350/450 ENH104V1-350/450 Color TFT-LCD Module Features GENERAL DESCRIPTION White Electronic Designs Display Systems Division provides optically enhanced solutions to the standard Sharp LQ104V1DG21 color active matrix LCD module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion).The second enhancement is the incorporation of an enhanced light guide (ELG) providing for up to 30% increase in brightness. This module is composed of a color TFT-LCD panel, driver ICs, and a backlight unit. Graphics and text can be displayed on a 640 X 3 X 480 dot panel with 262, 144 color by supplying 18-bit data signal (6bit/color), four timing signals, +3.3V/+5V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for multimedia use. Optimum viewing direction is 6 o'clock. Backlight-driving DC/AC inverter is not built in this module. White assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. White does assume the responsibility for the warranty of the enhanced product. SPECIFICATIONS Parameter Display size (cm) Active area (mm) Pixel format Pixel pitch (mm) Pixel configuration Display mode Unit outline dimensions (1) (mm) Mass (g) Surface treatment Specifications 26 (10.4") Diagonal 211.2 (H) x 158.4 (V) 640 (H) x 480 (V) (1 =R+G+B dots) 0.330 (H) x 0.330 (V) R,G,B vertical stripe Normally white 265.0 (W) x 195.0 (H) x 11.5max(D) 700 (max) IM/Clear (glossy) or IM/110 and hardcoat 3H Note: 1. Excluding backlight cables. Outline dimensions shown in Fig.1 Note: This measurement is typical, and see Fig. 3 for details. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 1 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division INPUT TERMINALS TTL-LCD Panel Driving CN1 Used connector: Corresponding connector: 1 31 2 30 ENH104V1-350/450 DF9BA-31P-1V (Hirose Electric Co., Ltd.) DF9 -31S-1V (Hirose Electric Co., Ltd.) DF9A-31S-1V (Hirose Electric Co., Ltd.) DF9B-31S-1V(Hirose Electric Co., Ltd.) DF9M-31S-1V(Hirose Electric Co., Ltd.) CN1 pin arrangement from module surface (Transparent view) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND CK HSYNC VSYNC GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND ENAB VCC VCC R/L U/D Function Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal RED data signal (LSB) RED data signal RED data signal RED data signal RED data signal RED data signal (MSB) GREEN data signal (LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (MSB) BLUE data signal (LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (MSB) Signal to settle the horizontal display position +3.3/5.0V power supply +3.3/5.0V power supply Horizontal display mode select signal Vertical display mode select signal Remarks (1) (1) (2) (3) (4) The shielding case is not connected with GND. Note: 1. 480 line, 400 line or 350 line mode is selected by the polarity combination of both synchronous signals. 2. The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is determined as described in Horizontal Display Position, p.6. Don't keep ENAB "High" during operation. Mode HSYNC VSYNC 480 lines negative negative 400 lines negative positive 350 lines positive negative White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 2 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division 3. ENH104V1-350/450 R/L = High, U/D = Low R/L = Low, U/D = Low CDEW WEDC 4. R/L = High, U/D = High R/L = Low, U/D = High WEDC Pin No. 1 2 3 Symbol VHIGH NC VLOW WEDC BACKLIGHT DRIVING CN2, CN3 Used connector: Corresponding connector: BHR-03VS-1(JST) SM02(8.0)B-BHS(JST) Function Power supply for lamp (High voltage side) This is electrically opened Power supply for lamp (Low voltage side) ABSOLUTE MAXIMUM RATINGS Parameter Input voltage +5V Supply voltage Storage temperature Operating temperature (Ambient) Symbol VI VCC tSTG Topa Condition tA=25°C tA=25°C - Ratings -0.3~ VCC + 0.3 0~ + 6 -30~ + 70 0~ + 65 Unit V V °C °C Remark (1) (2) Notes: 1. CK, RO~R5, G0~G5, B0`B5, HSYNC, VSYNC, ENAB, R/L, U/L 2. Humidity: 95%RH Max. at tA < 40°C Maximum wet-bulb temperature at 39°C or less at tA < 40°C No condensation. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 3 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 ELECTRICAL CHARACTERISTICS TFT-LCD PANEL DRIVING, tA=25°C Power Supply Parameter Supply voltage Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (Low) Input current (High) Symbol VCC MIN +3.0 TYP +3.3 -5.0 MAX +5.5 Unit V Remarks (1) ICC ICC VRF VIL VIH IOL1 IOL2 IOH1 IOH2 0.7VCC - (180) (150) - tBD tBD 100 0.3VCC 1.0 60.0 1.0 60.0 V mA mVp-p V V µA µA µA µA VCC = 3.3V (2) VCC = 3.3V (2) Vcc Notes: 1. VCC-turn-on conditions t1 < 15ms 0 < t2 < 100ms 0 < t3 < 1s t4 > 200ms VCC-dip conditions 1. 2.5V < VCC < 3.0V td < 10ms 2. VCC < 2.5V VCC-dip conditions should also follow the VCC-turn-on conditions 2. Typical current situation: 16-gray-bar pattern 480 line mode/Vcc=+3.3V 3. CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC,ENAB,R/L,U/D 4. CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC,ENAB 5. R/L 6. CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC 7. ENAB,U/D (3) VI=0V (4) VI=0V (5) VI=VCC(6) VI=VCC(7) 2.8V 2.8V data data 0.3V t4 0.3V t3 Vcc t1 t2 3.0V 2.4V t RGB RGB RGB RGB RGB GS0 GS3 GS7 GS59 GS63 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 4 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 BACKLIGHT DRIVING SECTION The backlight system is an edge-lighting type with single CCFT (Cold Cathode Fluorescent Tube). The characteristics of a single lamp are shown in the folliowing table.. Parameter Lamp current Lamp power consumption Lamp frequency Kickoff voltage Symbol IL PL FL VS Lamp life time MIN 2.0 20 50000 LL Module 1 3 1 3 TYP 6.0 3.0 35 - A ~ tA=25°C MAX 6.5 60 (950) (1250) (1500) - Unit mArms W KHz Vrms Vrms Vrms hour Remark (1) (2) (3) tA=25°C tA=0°C (4) tA=-10°C (4) (5) Inverter A ~ * 3pin is VLOW Notes: 1. Lamp current is measured with current meter for high frequency as shown above. 2. At the condition of IL= 6.0mArms 3. Lamp frequency may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display. Therefore, lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference. 4. The open output voltage of the inverter shall be maintained for more than 1 sec; otherwise the lamp may not be turned on. 5. Since lamp is consumables, the life time written above is referential value and it is not guaranteed in this specification sheet by White. Lamp life time is defined that it applied either (1) or (2) under this condition (Continuous turning on at tA=25°C, IL=6.0mArms) 1. Brightness becomes 50% of the original value under standard condition. 2. Kick-off voltage at tA=10°C exceeds maximum value,1500 Vrms. In case of operating under lower temp environment, the lamp degradation is accelerated and the brightness becomes lower. (Continuous operating for a minimum of one month under lower temp condition may reduce the brightness to 50% of the original brightness.) In case of such usage under lower temp environment, periodical lamp exchange by White is recommended 6. The performance of the backlight, for example life time; or brightness, is extremely infuenced by the characteristics of the DC-AC inverter, make certain that poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, ect.) do not occur. Once this is verified, the module should be operating in the same condition as it is installed in the instrument. 7. It is required to have the inverter designed to allow the impedance deviation of the two CCFT lamps and the capacity deviation of barast capacitor. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 5 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 TIMING CHARACTERISTICS OF INPUT SIGNALS Timing diagrams of input signal are shown in Fig.2 - (1)~(3). TIMING CHARACTERISTICS Parameter Clock Frequency High Time Low Time Data Set up time Hold time Horizontal sync. Cycle signal Clock Symbol 1/Tc Tch Tcl Tds Tdh TH Pulse width Cycle THp TV Pulse width Horizontal display period HSYNC-Clock phase difference HSYNC.-VSYNC. phase difference TVp THd THc TVh Vertical sync. signal Mode all all all all all all all all 480 400 350 all all all all Min. 5 10 5 10 30.00 750 2 515 446 447 1 640 10 0 Typ. 25.18 31.78 800 96 525 449 449 640 - Max. 28.33 900 200 560 480 510 34 640 Tc-10 TH-THp Unit MHz ns ns ns ns µs clock clock line line line line clock ns clock Notes: 1. In case of lower frequency, deterioration of the display quality, flicker, etc. may occur. HORIZONTAL DISPLAY POSITION The horizontal display position is determined by ENAB signal and the input data corresponding to the rising edge ENAB signal is displayed at the left end of the active area. Parameter Set-up time Pulse width HSYNC-enable signal phase difference Enable signal Symbol Tes Tep THe MIN 5 2 44 TYP 640 - MAX Tc-10 640 TH-664 Unit ns clock clock Notes: 1. When ENAB is fixed at "Low", the display starts from the data of C104 (clock) as shown in Fig.2 - (1)~(3). Be careful the module does not work when ENAB is fixed "High". When the phase difference is below 104 clock, keep the High level of ENAB signal longer than 104-The. If it is not kept, the display starts from the data of C104 (clock). White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 6 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division VERTICAL DISPLAY POSITION The vertical display position is automatically centered in the active area at each mode of VGA,480-,400-,and 350-line mode. Each mode is selected depending on the polarity of the synchronous signals described in on page 2 Input Terminals, Note 1. In each mode, the data of TVn is displayed at the top line of the active area. The display position will be centered Mode V-data start (TVs) V-data Perioc (TVd) 480 34 400 34 350 61 ENH104V1-350/450 on the screen like the following figure when the period of vertical synchronous signal, TV, is typical value. In 400-,and 350-line mode, the data in the vertical data invalid period is also displayed. So, inputting all data “0” is recommended during vertical data invalid period. ENAB signal has no relation to the vertical display position. V-display Start (TVn) V-display Period Unit 480 34 480 line 400 443-TV 480 line 350 445-TV 480 lute data invalid period data period data invalid period 4 0 lines 6 5 lines data invalid period data period 3 5 0 lines 4 0 0 lines 6 5 lines data invalid period 4 0 lines 350 lines mode (TV=449) 400 lines mode (TV=449) INPUT DATA SIGNALS AND DISPLAY POSITION ON THE SCREEN Display position of input data (480 lines mode) (H, V) UP D1, DH1 D2, DH1 D1, DH2 D2, DH2 D3, DH1 D640, DH1 D1, DH3 R D1, DH480 G B D640, DH480 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 7 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Data signal (R0~R5, G0~G5, B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) Data enable signal (ENAB) Data signal (R0~R5, G0~G5, B0~B5) Clock signal (CK) Horizontal sync. signal (Hsync) 0.3Vcc 0.7Vcc TVh 1 2 TVp 0.7Vcc D2 0.3Vcc 0.7Vcc 0.7Vcc Tep THd D3 0.3Vcc TH 34 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd Horizontal invalid data period Number of H-data Fig 2-1 Input signal waveforms (480 line mode) TVs Tes D1 Tds Tdh 0.7Vcc Number of clock C104* 0.3Vcc Vertical invalid data period 0.7Vcc 0.3Vcc THe Horizontal invalid data period C2* 0.3Vcc Tc Tch Tcl *Only when enable terminal is fixed "low" C1* 0.3Vcc THc 0.3Vcc 0.3Vcc THp TV DH479 DH480 0.3Vcc Number of V-data line Vertical invalid data period 0.3Vcc White Electronic Designs Display Systems Division ENH104V1-350/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 8 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Data signal (R0~R5, G0~G5, B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) THp C1* C2* 0.3Vcc 0.7Vcc TVh 1 2 TVp 0.7Vcc Tes TVs D2 0.3Vcc D3 Tds Tdh Tep THd 0.3Vcc 0.7Vcc 0.3Vcc 34 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd Horizontal invalid data period Number of H-data Fig 2-2 Input signal waveforms (400 line mode) Vertical invalid data period 0.7Vcc THe D1 Tc Tch Tcl 0.7Vcc Number of clock C104* 0.3Vcc *Only when enable terminal (ENAB) is fixed "low" 0.3Vcc THc 0.7Vcc Horizontal invalid data period 0.3Vcc 0.3Vcc Data enable signal (ENAB) Data signal (R0~R5, G0~G5, B0~B5) Clock signal (CK) Horizontal sync. signal (Hsync) TH TV DH399 White Electronic Designs Display Systems Division ENH104V1-350/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 9 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 0.7Vcc Data signal (R0~R5, G0~G5, B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) Data enable signal (ENAB) Data signal (R0~R5, G0~G5, B0~B5) Clock signal (CK) Horizontal sync. signal (Hsync) THc TVh 1 2 TVp 0.7Vcc D1 TVs Tes D2 0.3Vcc Tep THd 0.7Vcc D3 0.7Vcc 0.3Vcc Tds Tdh 0.7Vcc Tc Tch Tcl 61 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd TV Horizontal invalid data period Number of H-data Fig 2-3 Input signal waveforms (350 line mode) Vertical invalid data period 0.3Vcc 0.3Vcc THe 0.3Vcc C2* C104* Number of clock Horizontal invalid data period C1* 0.3Vcc *Only when enable terminal (ENAB) is fixed to "Low" 0.3Vcc 0.3Vcc 0.3Vcc THp 0.7Vcc TH DH349 White Electronic Designs Display Systems Division ENH104V1-350/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 10 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 INPUT SIGNALS, BASIC DISPLAY COLORS AND GRAY SCALE OF EACH COLOR Gray Scale of Red Basic Color Colors & Grayscale Black Blue Green Cyan Red Magenta Yellow White Black Darker Brighter Gray Scale of Green Red Black Darker Brighter Gray Scale of Blue Green Black Darker Brighter Blue Data signal Gray Scale GS0 GS1 GS2 R0 0 0 0 0 1 1 1 1 0 1 0 R1 0 0 0 0 1 1 1 1 0 0 1 R2 0 0 0 0 1 1 1 1 0 0 0 R3 0 0 0 0 1 1 1 1 0 0 0 R4 0 0 0 0 1 1 1 1 0 0 0 R5 0 0 0 0 1 1 1 1 0 0 0 G0 0 0 1 1 0 0 1 1 0 0 0 G1 0 0 1 1 0 0 1 1 0 0 0 G2 0 0 1 1 0 0 1 1 0 0 0 G3 0 0 1 1 0 0 1 1 0 0 0 G4 0 0 1 1 0 0 1 1 0 0 0 G5 0 0 1 1 0 0 1 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 B2 0 1 0 1 0 1 0 1 0 0 0 B3 0 1 0 1 0 1 0 1 0 0 0 B4 0 1 0 1 0 1 0 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0 GS61 GS62 GS63 GS0 GS1 GS2 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS61 GS62 GS63 GS0 GS1 GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS61 GS62 GS63 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes: 1. 0: Low level voltage 1: High level voltage. 2. Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262, 144-color display can be achieved on the screen. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 11 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 OPTICAL CHARACTERISTICS tA=25°C, VCC=+5V Parameter Symbol Horizontal Viewing Angle Range Vertical Contrast Ratio θ11 Rise Decay Luminance of White θ = 0° Best Viewing Angle tr td YL Chromaticity of White White Uniformity Viewing Angle Range as a Brightness Definition (CR>10) θ12 CR Response Time Condition θ21, θ22 Horizontal Vertical x y δw θ21, θ22 θ11 θ12 θ = 0° 50% of the maximum brightness Min 60 35 55 150 280 360 - Typ 70 40 70 250 20 40 350 450 0.313 0.329 50 40 35 Max 1.45 - Unit Deg. Deg. Deg. ms ms cd/m2 cd/m2 Deg. Deg. Deg. Remarks (1, 4) (2, 4) (2, 4) (3, 4) (4) IL=6.0mArms f=35kHz (5) (1) The measurements shall be executed 30 minutes after lighting at rating. (typical condition: IL=6mArms) The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig. 3 below. Photodetector (BM-5A: TOPCON) Parameter Luminance of White IM Film IM, ELG Min. Typ. Max. Unit 280 350 350 450 - cd/m2 - Field=2° 400mm TFT-LCD Module LCD Panel Center of the screen Fig. 3 Optical characteristics measurement method White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 12 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH104V1-350/450 Notes: 1. Definition of viewing angle range: 2. Definition of contrast ratio The contrast ratio is defined as follows: Contrast Ratio (CR)= 3. 4. 5. Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black Normal line θ 22 θ 12 θ 11 θ 21 Definition of response time The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". This shall be measured at the center of the screen. Definition of white uniformity: White uniformity is defined as the following with five measurements. (A~E). 6 o'clock direction Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness) black white Photodetector output (Relative Value) δw= white 100% 90% 10% 0% τd τr time 160 320 A 480 pixel D C B 120 240 E 360 pixel White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 13 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division DISPLAY QUALITY The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. HANDLING PRECAUTIONS 1. Be sure to turn off the power supply when inserting or disconnecting the cable. 2. Design the cabinet so that the module can be installed without any extra stress such as warp or twist. 3. Since the front polarizer is easily damaged, pay attention not to scratch it 4. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 5. When the panel surface is soiled, use an absorbent cotton or other soft cloth to wipe it off. 6. Since the panel is made of glass and refined wires and components, it may break,crack or internal wire breaking if dropped or bumped on hard surface. Handle with care. ENH104V1-350/450 10. Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment. 11. Connect GND to 4 place of mounting holes to stabilize against EMI and external noise 12. The high voltage portions on the backlight are very dangerous. Careless handling may lead to electrical shock. When exchanging lamps or service, turn off the power without fail. 13. When handling LCD modules and assembling then into cabinets, be aware that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules. 14. Cold cathode flourescent lamp in LCD panel contains a small amount of mercury, follow local ordinances or regulations for disposal. PACKING FORM 7. Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling. 1. Piling number of cartons : MAX 7 2. Package quantity in one carton: 20 8. Laminated film is attached to the front and back of the module surface to prevent it from being scratched. Peel the film off slowly, just before use, with strict attention to electrostatic charges, Ionized air should be blown over during the action. Blow off 'dust' on the polarizer by using an ionized nitrogen gun, etc. 4. Total mass of 1 carton filled with full modules : 17.5kg 9. The polarizer surface on the panel is treated with AntiGlare for low reflection. 3. Carton size: 525(W) X 309(D) X 377(H) OTHERS 1. Disassembling the module can cause permanent damage and should be avoided. 2. Be adviced that image retention may occur when a fixed pattern is displayed for a long period of time. RELIABILITY TEST ITEMS No. 1 2 3 4 5 6 7 Test items High temperature storage test Low temperature storage test High temperature and high humidity operating test High temperature operating test Low temperature operating test Vibration Test (Non-operating) Shock test (non-operating) Conditions tA=70°C tA=-30°C tA=40°C, 95%RH (No condensation) tA=65°C tA=-10°C Frequency Sweep time Test Period Max gravity Pulse width Direction 240h 240h 240h 240h 240h :10~57Hz/Vibration width (one side): 0.075mm :58~500Hz/Gravity: 9.8m/s2 :11 minutes :3 hours (1 hour for each direction of X, Y, Z) :490m/s2 :11 minutes, half sine wave :±X, ±Y, ±Z (once for each direction.) (Result Evaluation Criteria) Under the display quality test conditions with normal operation state, there shall be no change which may affect practical display function. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 14 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 +0.5 2.4 -0.5 6.7 5.7 195 182 SEE DETAIL A (99.05) 5mm MAX 3-4.3mm (138.4) 5mm MAX HEIGHT STANDARD (H=0) IS PRINTED WIRING BOARD 2mm MAX 4 10 CONNECTOR OF I/F AND CIRCUMFERENCE DIAGRAM ARROW SHOWS 6 O'CLOCK VIEWING ANGLE 25 25 11.5 MAX (91) 5.5 2.5 13.5 FOR M2 TAPPING SCREW 3-Ø1.7 DEPTH 3.5mm 3-4.3mm CN1 NO.2 NO.30 21.6 NO. 31 NO. 1 256 105.6 (Active Area) 107.3 (Bezel Opening) 105.6 (Active Area) 107.3 (Bezel Opening) Active Area Center Active Area (211.2 x 158.4) Bezel Opening (214.6 x 162.4) 265 81.2 (Bezel Opening) LOT NUMBER LABEL (124.9) (66.3) 3. GND CN2 1. HOT +10 90 -5 +10 90 -5 3. GND CN3 1. HOT SEE DETAIL B SEE DETAIL B ENVIRONMENT LABEL REAR VIEW (116.6) (138.4) 79.2 (Active Area) 81.2 (Bezel Opening) 79.2 (Active Area) SEE DETAIL A (40) (74) 132.6 (143.9) 2.5 5.5 4.5 7 1. R R3 FIG. 1 OUTLINE DIMENSIONS 3.4 4.5 (256) CN2, 3: BHR-03VS-1 VHIGH 1 NC 2 VLOW 3 CN1:DF9MA-31P-1V 1 GND 2 CK Hsync 3 4 Vsync GND 5 R0 6 7 R1 8 R2 R3 9 10 R4 R5 11 GND 12 13 G0 14 G1 G2 15 16 G3 17 G4 G5 18 19 GND B0 20 B1 21 22 B2 23 B3 B4 24 25 B5 GND 26 ENAB 27 28 Vcc 29 Vcc R/L 30 U/D 31 ACTIVE AREA BEZEL OPENING B A: 1.7 ± 0.8 B: 1.7 ± 0.8 C: 2.0 ± 0.8 D: 2.0 ± 0.8 |E-F| < 0.8 NOTES 1. UNSPECIFIED TOLERANCE TO BE ± 0.5 2. PLEASE DESIGN USER'S CABINET BOSSES WITH 6mm TO 8mm IN DIAMETER. (1) TOLERANCE X-DIRECTION (2) TOLERANCE X-DIRECTION (3) TOLERANCE Y-DIRECTION (4) TOLERANCE Y-DIRECTION (5) OBLIQUITY OF DISPLAY AREA A BEZEL/DISPLAY POSITION ENLARGED DETAIL B 4.5 ENLARGED DETAIL A 1 E (I/F PRINTED WIRING BOARD) 16 16 20 20 40 30 4.5 4.5 FRONT VIEW 6 6 ∅ 3. 4 C D Original specifications created by Sharp. F White Electronic Designs Display Systems Division ENH104V1-350/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 15 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0