FRF1001G - FRF1007G Isolated 10 AMPS. Glass Passivated Fast Recovery Rectifiers ITO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss Mechanical Data Cases: ITO-220AB molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Pure tin plated, Lead free. Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260 oC /10 seconds 0.25”,(6.35mm) from case. Mounting position: Any Weight: 2.24 grams Mounting torque: 5 in – 1bs. max. Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FRF FRF FRF FRF FRF FRF FRF 1001G 1002G 1003G 1004G 1005G 1006G 1007G Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A V RRM V RMS V DC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V I(AV) 10 A IFSM 125 A VF 1.3 V Maximum DC Reverse Current @ T C =25 C o at Rated DC Blocking Voltage @ T C =125 C IR 5.0 100 Maximum Reverse Recovery Time ( Note 1) Trr uA uA nS pF o C/W o C o Typical Junction Capacitance (Note 3) Typical Thermal Resistance RθJC (Note 2) Cj R θJC 150 250 40 5.0 -65 to +150 Operating and Storage Temperature Range T J ,T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink. 3. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C. 500 Version: A06 RATINGS AND CHARACTERISTIC CURVES (FRF1001G THRU FRF1007G) 1000 10 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 12 8 6 4 2 0 50 100 150 o CASE TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 Tj=125 0C 10 1 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 150 TJ=125 0C 125 0.1 8.3ms Single Half Sine Wave JEDEC Method 100 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 75 50 80 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 25 40 0 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 150 125 CAPACITANCE.(pF) 20 INSTANTANEOUS FORWARD CURRENT. (A) 1 100 75 50 10 4 2 1 0.4 0 25 0 0.1 Tj=25 C f=1.0MHz Vsig=50mVp-p 0.5 1 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.2 5 10 50 100 0.1 0.8 500 1000 0.9 1.0 1.1 1.2 1.3 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06