[ /Title (CD74 HC112 , CD74 HCT11 2) /Subject (Dual J-K FlipFlop with Set and Reset Nega- CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Data sheet acquired from Harris Semiconductor SCHS141H Dual J-K Flip-Flop with Set and Reset Negative-Edge Trigger March 1998 - Revised October 2003 Features Description • Hysteresis on Clock Inputs for Improved Noise Immunity and Increased Input Rise and Fall Times The ’HC112 and ’HCT112 utilize silicon-gate CMOS technology to achieve operating speeds equivalent to LSTTL parts. They exhibit the low power consumption of standard CMOS integrated circuits, together with the ability to drive 10 LSTTL loads. • Asynchronous Set and Reset • Complementary Outputs These flip-flops have independent J, K, Set, Reset, and Clock inputs and Q and Q outputs. They change state on the negative-going transition of the clock pulse. Set and Reset are accomplished asynchronously by low-level inputs. • Buffered Inputs • Typical fMAX = 60MHz at VCC = 5V, CL = 15pF, TA = 25oC • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The HCT logic family is functionally as well as pincompatible with the standard LS logic family. . • Wide Operating Temperature Range . . . -55oC to 125oC Ordering Information • Balanced Propagation Delay and Transition Times PART NUMBER • Significant Power Reduction Compared to LSTTL Logic ICs TEMP. RANGE (oC) PACKAGE CD54HC112F3A -55 to 125 16 Ld CERDIP • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V CD54HCT112F3A -55 to 125 16 Ld CERDIP CD74HC112E -55 to 125 16 Ld PDIP CD74HC112MT -55 to 125 16 Ld SOIC • HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH CD74HC112M96 -55 to 125 16 Ld SOIC CD74HC112NSR -55 to 125 16 Ld SOP CD74HC112PW -55 to 125 16 Ld TSSOP CD74HC112PWR -55 to 125 16 Ld TSSOP CD74HC112PWT -55 to 125 16 Ld TSSOP CD74HCT112E -55 to 125 16 Ld PDIP Pinout NOTE: When ordering, use the entire part number. The suffixes 96 and R denote tape and reel. The suffix T denotes a small-quantity reel of 250. CD54HC112, CD54HCT112 (CERDIP) CD74HC112 (PDIP, SOIC, SOP, TSSOP) CD74HCT112 (PDIP) TOP VIEW 1CP 1 16 VCC 1K 2 15 1R 1J 3 14 2R 1S 4 13 2CP 1Q 5 12 2K 1Q 6 11 2J 2Q 7 10 2S GND 8 9 2Q CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © 2003, Texas Instruments Incorporated 1 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Functional Diagram 1S 1J 1K 1CP 1R 2S 2J 2K 2CP 2R 4 3 5 1Q 2 F/F 1 6 1Q 1 15 10 11 9 2Q 12 F/F 2 7 2Q 13 GND = 8 VCC = 16 14 TRUTH TABLE INPUTS OUTPUTS S R CP J K Q Q L H X X X H L H L X X X L H L L X X X H (Note 1) H (Note 1) H H ↓ L L H H ↓ H L H L H H ↓ L H L H H H ↓ H H Toggle H H H X X No Change No Change H= High Level (Steady State) L= Low Level (Steady State) X= Don’t Care ↓= High-to-Low Transition NOTE: 1. Output states unpredictable if both S and R go High simultaneously after both being low at the same time. 2 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Drain Current, per Output, IO For -0.5V < VO < VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . . . . . .±25mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA Package Thermal Impedance, θJA (see Note 2): E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67oC/W NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W D (SOIC) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73oC/W PW (TSSOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W Maximum Junction Temperature (Hermetic Package or Die) . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time, tr, tf 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0ms (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0ms (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0ms (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 2. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS PARAMETER SYMBOL VI (V) VIH - 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current II VCC or GND - - -0.02 2 1.9 - - 1.9 - 1.9 - V 4.5 4.4 - - 4.4 - 4.4 - V 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 4.5 - - 0.1 - 0.1 - 0.1 V 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V - 6 - - ±0.1 - ±1 - ±1 µA 3 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) ICC VCC or GND 0 High Level Input Voltage VIH - Low Level Input Voltage VIL High Level Output Voltage CMOS Loads VOH PARAMETER Quiescent Device Current 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 6 - - 4 - 40 - 80 µA - 4.5 to 5.5 2 - - 2 - 2 - V - - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V VIH or VIL -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V ±0.1 - ±1 - ±1 µA HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC and GND - 5.5 - ICC VCC or GND 0 5.5 - - 4 - 40 - 80 µA ∆ICC (Note 3) VCC - 2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 µA NOTE: 3. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS 1S, 2S 0.5 1K, 2K 0.6 1R, 2R 0.65 1J, 2J, 1CP, 2CP 1 NOTE: Unit Load is ∆ICC limit specified in DC Electrical Specifications table, e.g., 360µA max at 25oC. Prerequisite For Switching Specifications PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tW - 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns HC TYPES Pulse Width CP 4 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Prerequisite For Switching Specifications PARAMETER Pulse Width R, S Setup Time J, K, to CP Hold Time J, K, to CP Removal Time R to CP, S to CP CP Frequency (Continued) 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tW - 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 0 - - 0 - 0 - ns 4.5 0 - - 0 - 0 - ns 6 0 - - 0 - 0 - ns 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 6 - - 5 - 4 - MHz tSU - tH - tREM - fMAX - 4.5 30 - - 25 - 20 - MHz 6 35 - - 29 - 23 - MHz HCT TYPES Pulse Width CP tSU - 4.5 16 - - 20 - 24 - ns Pulse Width R, S tW - 4.5 18 - - 23 - 27 - ns Setup Time J, K, to CP tH - 4.5 16 - - 20 - 24 - ns Hold Time J, K, to CP tREM - 4.5 3 - - 3 - 3 - ns tW - 4.5 20 - - 25 - 30 - ns fMAX - 4.5 30 - - 25 - 20 - MHz SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPLH, tPHL CL = 50pF 2 - - 175 - 220 - 265 ns CL = 50pF 4.5 - - 35 - 44 - 53 ns CL = 15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 45 ns Removal Time R to CP, S to CP CP Frequency Switching Specifications Input tr, tf = 6ns PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC HC TYPES Propagation Delay, CP to Q, Q Propagation Delay, S to Q, Q Propagation Delay, R to Q, Q tPLH, tPHL tPLH, tPHL CL = 50pF 2 - - 155 - 195 - 235 ns CL = 50pF 4.5 - - 31 - 39 - 47 ns CL = 15pF 5 - 13 - - - - - ns CL = 50pF 6 - - 26 - 33 - 40 ns CL = 50pF 2 - - 180 - 225 - 270 ns CL = 50pF 4.5 - - 36 - 45 - 54 ns CL = 15pF 5 - 15 - - - - - ns CL = 50pF 6 - - 31 - 38 - 46 ns 5 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Switching Specifications Input tr, tf = 6ns (Continued) 25oC -40oC TO 85oC -55oC TO 125oC PARAMETER SYMBOL TEST CONDITIONS Output Transition Time tTLH, tTHL CL = 50pF 2 - - 75 - 95 - 110 ns CL = 50pF 4.5 - - 15 - 19 - 22 ns CL = 50pF 6 - - 13 - 16 - 19 ns - - - 10 - 10 - 10 pF 5 - 60 - - - - - MHz 5 - 12 - - - - - pF CL = 50pF 4.5 - - 35 - 44 - 53 ns CL = 15pF 5 - 14 - - - - - ns CL = 50pF 4.5 - - 32 - 40 - 48 ns CL = 15pF 5 - 13 - - - - - ns CL = 50pF 4.5 - - 37 - 46 - 56 ns CL = 15pF 5 - 14 - - - - - ns CL = 50pF 4.5 - - 15 - 19 - 22 ns Input Capacitance CI VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS - CP Frequency fMAX Power Dissipation Capacitance (Notes 4, 5) CPD CL = 15pF - HCT TYPES Propagation Delay, CP to Q, Q tPLH, tPHL Propagation Delay, S to Q, Q tPLH, tPHL Propagation Delay, R to Q, Q tPLH, tPHL Output Transition Time tTLH, tTHL Input Capacitance CI - - - - 10 - 10 - 10 pF CP Frequency fMAX CL = 15pF 5 - 60 - - - - - MHz Power Dissipation Capacitance (Notes 4, 5) CPD - 5 - 20 - - - - - pF NOTES: 4. CPD is used to determine the dynamic power consumption, per flip-flop. 5. PD = CPD VCC2 fi + Σ CL fo where fi = input frequency, fo = output frequency, CL = output load capacitance, VCC = supply voltage. Test Circuits and Waveforms tfCL trCL CLOCK 90% 10% tWL + tWH = I tWL 50% tfCL = 6ns fCL I fCL 3V VCC 50% 10% tWL + tWH = trCL = 6ns CLOCK 50% 2.7V 0.3V GND 1.3V 0.3V tWL tWH NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. 1.3V 1.3V GND tWH NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH FIGURE 2. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH 6 CD54HC112, CD74HC112, CD54HCT112, CD74HCT112 Test Circuits and Waveforms tr = 6ns (Continued) tf = 6ns 90% 50% 10% INPUT GND tTLH 90% INVERTING OUTPUT tPHL FIGURE 3. HC AND HCU TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC trCL VCC 90% GND tH(H) 3V 2.7V 1.3V 0.3V GND tH(H) tH(L) VCC DATA INPUT DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 5. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET tfCL CLOCK INPUT 50% 10% tPLH FIGURE 4. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tfCL trCL tTLH 1.3V 10% tPLH tPHL GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL CLOCK INPUT tf = 6ns tr = 6ns VCC CL 50pF FIGURE 6. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 7 PACKAGE OPTION ADDENDUM www.ti.com 9-May-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking TBD Call TI Call TI -55 to 125 5962-8970201EA CD54HCT112F3A (4/5) 5962-8970201EA ACTIVE CDIP J 16 CD54HC112F3A ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 8408801EA CD54HC112F3A CD54HCT112F3A ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8970201EA CD54HCT112F3A CD74HC112E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC112E CD74HC112EE4 ACTIVE PDIP N 16 TBD Call TI Call TI -55 to 125 CD74HC112E CD74HC112M96 ACTIVE SOIC D 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC112M CD74HC112M96E4 ACTIVE SOIC D 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112M96G4 ACTIVE SOIC D 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112MT ACTIVE SOIC D 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC112M CD74HC112MTE4 ACTIVE SOIC D 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112MTG4 ACTIVE SOIC D 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112NSR ACTIVE SO NS 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC112M CD74HC112NSRE4 ACTIVE SO NS 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112NSRG4 ACTIVE SO NS 16 TBD Call TI Call TI -55 to 125 HC112M CD74HC112PW ACTIVE TSSOP PW 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HJ112 CD74HC112PWE4 ACTIVE TSSOP PW 16 TBD Call TI Call TI -55 to 125 HJ112 CD74HC112PWG4 ACTIVE TSSOP PW 16 TBD Call TI Call TI -55 to 125 HJ112 CD74HC112PWR ACTIVE TSSOP PW 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HJ112 2500 250 2000 90 2000 Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 9-May-2014 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) CD74HC112PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HJ112 CD74HC112PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HJ112 CD74HC112PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HJ112 CD74HC112PWTE4 ACTIVE TSSOP PW 16 TBD Call TI Call TI -55 to 125 HJ112 CD74HC112PWTG4 ACTIVE TSSOP PW 16 TBD Call TI Call TI -55 to 125 HJ112 CD74HCT112E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT112E CD74HCT112EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT112E (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 9-May-2014 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF CD54HC112, CD54HCT112, CD74HC112, CD74HCT112 : • Catalog: CD74HC112, CD74HCT112 • Military: CD54HC112, CD54HCT112 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device CD74HC112M96 Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 CD74HC112NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 CD74HC112PWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 CD74HC112PWT TSSOP PW 16 250 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74HC112M96 SOIC D 16 2500 333.2 345.9 28.6 CD74HC112NSR SO NS 16 2000 367.0 367.0 38.0 CD74HC112PWR TSSOP PW 16 2000 367.0 367.0 35.0 CD74HC112PWT TSSOP PW 16 250 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated