Ordering number : ENA2014 LB1973JA Monolithic Digital IC Two-channel H-Bridge Driver http://onsemi.com Overview The LB1973JA is a two-channel H-bridge driver that supports for low saturation draive operation. It is optimal for H-bridge drive of stepping motors (AF and zoom) in portable equipment such as camera cell phones. Features • Two-channel H-bridge driver • 2ch simultaneous connection is possible • Parallel input interface • 2 phase excitation, 1-2 phase excitation drive are possible • The range of the operation voltage is wide.(1.8V to 7.5V) • Built-in thermal protection Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Output voltage Symbol Conditions VCC max VOUT max Ratings Unit -0.3 to +8.0 V - VSF to VCC+VSF V Input voltage VIN max -0.3 to +8.0 Spark killer Di order direction electric ISF max 1000 Ground pin source current Allowable power dissipation IGND Per channel Pd max *Mounted on a bord V mA 1000 mA 800 mW Operating temperature Topr -20 to +85 °C Storage temperature Tstg -40 to +150 °C * Mounted on a Specified board : 114.3mm×76.1mm×1.6mm, glass epoxy Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Allowable Operating Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC High-level input voltage VIH RIN = 1kΩ 1.3 to 7.5 V Low-level input voltage VIL RIN = 1kΩ -0.3 to +0.5 V Semiconductor Components Industries, LLC, 2013 June, 2013 1.8 to 7.5 V 30712 SY 20120117-S00010 No.A2014-1/5 LB1973JA Electrical Characteristics at Ta = 25°C, VCC = 1.9V Parameter Source current Output saturation voltage1 Symbol Conditions Ratings min typ Unit max ICCO1 VCC = 1.9V,IN1 to IN4 = Low level 0.01 1 μA ICCO2 VCC = 3V,IN1 to IN4 = Low level 0.01 1 μA ICC1 IN1 = High level,IN2 to IN4 = Low level 18 25 mA ICC2 IN1 = High level,IN2 to IN4 = Low level, VCC = 3V 19 27.5 mA IOUT = 270mA,VCC = 1.9V to 3.6V, 0.2 0.3 V 0.25 0.4 V 0.12 0.2 V 0.2 0.35 V VOUT11 Ta = -20 to 85°C (single connection) VOUT = Upper Tr and Under Tr IN1 = High level, IN2 to IN4 = Low level Supplementation: Standard similar as for IN2 to IN4 = High level VOUT12 IOUT = 350mA,VCC = 1.9V to 3.6V, Ta = -20 to 85°C VOUT = Upper Tr and Under Tr IN1 = High level, IN2 to IN4 = Low level Supplementation: Standard similar as for IN2 to IN4 = High level Output saturation voltage2 VOUT21 IOUT = 270mA,VCC = 1.9V to 3.6V, Ta = -20 to 85°C (parallel connection) VOUT = Upper Tr and Under Tr OUT1-3,OUT2-4 short. IN1 and IN3 = High level, IN2 and IN4 = Low level Supplementation: Standard similar as for IN2 and IN4 = High level VOUT22 IOUT = 500mA,VCC = 1.9V to 3.6V, Ta = -20 to 85°C VOUT = Upper Tr and Under Tr OUT1-3,OUT2-4 short. IN1 and IN3 = High level,IN2 and IN4 = Low level Supplementation: Standard similar as for IN2 and IN4 = High level Output electric current with the IPA VIN = 1.9 to 3.6V, Ta = -20 to 85°C *1 9 mA 70 μA parasitic element Input current Themal shutdown operation IIN VIN = 1.9V 32 Ttsd *2: Design guarantee 140 °C ∆T *2: Design guarantee 20 °C temperature Temperature hysteresis width Spark killer Diode Reverse current IS(leak) Forword voltage VSF VCC-OUT = 8V, VIN = Low level 10 μA ISF = 400mA, VIN = Low level 1.7 V *1: Output electric current with the parasitic element_IPA: The current value that the off ch(-free) output is pulled at the time of one side ch drive by a parasitic element *2: Design guarantee value and does not measure * VSF: The current order direction voltage true in a time No.A2014-2/5 LB1973JA Package Dimensions unit : mm (typ) 3178B Pd max -- Ta 1.0 0.5 6.4 9 4.4 16 Allowable power dissipation,Pd max - W 5.2 1 8 0.65 0.15 (0.33) 1.5max 0.22 Mounted on a specified board : 114.3mm x 76.1mm x 1.6mm glass epoxy 0.8 0.6 0.4 0.2 0 -20 20 (1.3) 0 40 60 80 85 100 0.1 Ambient temperature, Ta -- C SANYO : SSOP16(225mil) 9 8 NC GND 10 7 IN2 11 6 IN1 NC OUT2 OUT1 5 NC 12 4 IN3 13 NC OUT3 14 3 IN4 OUT4 15 2 NC 16 1 VCC NC Pin Assignment (Top View) Truth Table Input IN1 Output IN2 IN3 IN4 Low Low Low Low High Low Low High - - High - - - High Low Low High High - - - High High OUT1 OUT2 OUT3 OUT4 Off Off - - Off Off High Low Low High - - Mode Standby mode Channel 1, forward Channel 1, reverse High Low Channel 2, forward Low High Channel 2, reverse The logic output for the first high-level input is produced. No.A2014-3/5 LB1973JA Stepping motor control example (1) Timing chart for 2-phase drive IN1 IN2 IN3 IN4 Channel 1 output mode Standby Channel 2 output mode Standby Forward Reverse Forward Forward Reverse Reverse Forward Forward Standby Reverse Forward Standby (2) Timing chart for 1-2 phase drive IN1 IN2 IN3 IN4 Channel 1 output mode Standby Channel 2 output mode Standby Forward OFF Reverse OFF Forward OFF Reverse Forward Standby OFF Forward Standby No.A2014-4/5 LB1973JA Block Diagram VCC 30K OUT2 IN2 100K 30K IN3 100K Control Block Circuit 30K IN1 Thermal shutdown circuit 100K OUT1 OUT3 OUT4 30K IN4 100K GND ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2014-5/5