NTE NTE1890 Integrated circuit ntsc decoder for tv Datasheet

NTE1890
Integrated Circuit
NTSC Decoder for TV
Description:
The NTE1890 is a monolithic integrated decoder for the NTSC color television standards. It combines
all functions required for the demodulation of NTSC signals. Further more it contains a luminance
amplifier, an RGB–matrix and amplifier. These amplifiers supply output signals up to 5V peak–to–
peak (picture information) enabling direct drive of the discrete output stages.
Absolute Maximum Ratings:
Maximum Supply Voltage (Pin1), VP = V1–23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2V
Maximum Total Power Disipation, Ptot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7W
Operating Ambient Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25° to +65°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25° to +150°C
Thermal Resistance, Junction–to–Ambient, RthJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50K/W
Electrical Characteristics: (VP = V1–23 = 12V, TA = +25°C unless otherwise specified)
Parameter
Symbol
Min
Typ
Max
Unit
Supply Voltage
VP = V1–23
8.0
12.0
13.2
V
Supply Current
IP = I1
–
85
–
mA
Ptot
–
1.0
–
W
V9–23(p–p)
–
450
–
mV
V9–23
–
–
2
V
I9
–
0.15
1.0
µA
–17
–
+3
dB
–
1.2
–
V
I7
–
–
15
µA
|Z10–23|
–
200
–
Ω
–
3
–
Supply (Pin1)
Total Power Dissipation
Luminance Amplifier (Pin9)
Input Voltage (Peak–to–Peak Value, Note 1)
Input Level Before Clipping
Input Current
Contrast Control Range
Control Voltage for an Attenuation of 40dB
Input Current Contrast Control
Peaking of Luminance Signal
Output Impedance (Pin10)
Ratio of Internal/External Current when Pin10 is Short–Circuited
Control Voltage for Peaking Adjustment (Pin11)
V11–23
–
2.4
–
V
Input Impedance (Pin11)
|Z11–23|
–
10
–
kΩ
Note 1. Signal with the negative–going sync; amplitude includes sync amplitude.
Electrical Characteristics (Cont’d): (VP = V1–23 = 12V, TA = +25°C unless otherwise specified)
Parameter
Symbol
Min
Typ
Max
Unit
V3–23(p–p)
55
550
1100
mV
Input Impedance
|Z3–23|
–
8
–
kΩ
Input Capacitance
C3–23
–
4
6
pF
ACC Control Range
30
–
–
dB
Change of the Burst Signal at the Output over the Whole Control Range
–
–
1
dB
Gain at Nominal Contrast/Saturation Pin3 to Pin24 (Note 3)
13
–
–
dB
Chrominance Amplifier (Pin3)
Input Voltage (Peak–to–Peak Value, Note 2)
Output Voltge (Peak–to–Peak Value at Burst Signal of 300mV(p–p),
(Note 3)
V24–23(p–p)
–
240
–
mV
Maximum Output Voltage Range (Pin24, Peak–to–Peak Value)
V24–24(p–p)
–
1.7
–
V
d
–
3.0
5.0
%
α24–3
–
–
–2
dB
50
–
–
dB
–
–
20
µA
Tracking Between Luminance and Chrominance Contrast Control
–
–
2
dB
Cross–Coupling Between Luminance and Chrominance Amplifier
(Note 4)
–
–
–46
dB
56
–
–
dB
–
–
±5
deg
|Z24–23|
–
25
–
Ω
I24
–
–
10
mA
∆f
500
700
–
Hz
–
–
5
deg
Distortion of Chrominance Amplifier at V24–23(p–p) = 0.5V (Output)
up to V3–23(p–p) = 1V (Input)
Frequency Response Between 0 and 5MHz
Saturation Control Range
Input Current Saturation Control (Pin6)
Signal–to–Noise Ratio at Nominal Input Signal (Note 5)
I6
S/N
Phase Shift Between Burst and Chrominance at Nominal
Contrast/Saturation
Output Impedance of Chrominance Amplifier
Output Current
Reference Part (Phase–Locked Loop)
Catching Range (Note 6)
Phase Shift for ±400Hz Deviation for fOSC (Note 6)
Reference Part (Oscillator)
Temperature Coefficient of Oscillator Frequency (Note 6)
TCOSC
–
–1.5
–
Hz/K
Frequency Variation when Supply Voltage Increases from
10V to 13.2V (Note 6)
∆fOSC
–
40
–
Hz
Input Resistance (Pin22)
R22–23
–
300
–
Ω
Input Capacitance (Pin22)
C22–23
–
–
10
pF
Note 2. Indicated is a signal for a color bar with 75% saturation; chrominance to burst ratio is 2.2:1.
Note 3. Nominal contrast is specified as the maximum contrast –3dB and nominal saturation as the
maximum saturation –6dB.
Note 4. Cross coupling is measured under the following conditions:
S Input signals nominal.
S Contrast and aturation such that the nominal output signals are obtained.
S The signals at the output at which no signal should be available must be compared
with the nominal output signal at that output.
Note 5. The signal–to–noise ratio is defined as peak–to–peak signal with respect to RMS noise.
Note 6. All frequency variations are referred to 3.58MHz carrier frequency.
Electrical Characteristics (Cont’d): (VP = V1–23 = 12V, TA = +25°C unless otherwise specified)
Parameter
Symbol
Min
Typ
Max
Unit
Control Voltage at Nominal Input Signal
V2–23
–
5.3
–
V
Control Voltage without Chrominance Input
V2–23
–
2.8
–
V
Color–Off Voltage
V2–23
–
3.4
–
V
Color–On Voltage
V2–23
–
3.6
–
V
Reference Part (ACC Generation, Pin22)
Change in Burst Amplitude with Supply Voltage
Voltage at Pin4 at Nominal Input Signal
Independent
V4–23
–
5.2
–
V
±50
–
–
deg
V17–23(p–p)
–
320
–
mV
|Z17–23|
–
2
–
kΩ
Ratio of Demodulated Signals (B–Y)/(R–Y)
V15–23/V13–23
–
1.1
–
Ratio of Demodulated Signals (G–Y)/(R–Y); No (B–Y) Signal
V14–23/V13–23
–
0.26
–
Ratio of Demodulated Signals (G–Y)/(B–Y); No (R–Y) Signal
V14–23/V15–23
–
0.22
–
Frequency Response Between 0 and 1MHz
–
–
–3
dB
Crosstalk Between Color Difference Signals
40
–
–
dB
V13, 14, 15–23(p–p)
–
5
–
V
V13–23(p–p)
–
5.25
–
V
V13, 14, 15–23
9.0
9.3
9.6
V
I13, 14, 15
–
–
10
mA
V13, 14, 15–23
–
2.7
–
V
–
–
40
mV
I12
–
–
5
µA
∆V/∆T
–
0.35
1.0
mV/K
∆V
–
10
100
mV
Relative Spread Between the R, G and B Output Signals
–
–
10
%
Relative Black–Level Varition Between the Three Channels During
Variation of Contrast, Brightness and Supply Voltage
–
0
20
mV
Differential Black–Level Drift Over a Temperature Range of 40°C
–
0
20
mV
Reference Part (Hue Control)
Control Range
Demodulator Part
Input Burst Signal Amplitude (Peak–to–Peak Value, Pin17)
Input Impedance (Pin17, Note 7)
RGB Matrix and Amplifiers
Output Voltage at Nominal Input Signal
(Peak–to–Peak value, Black–to–White, Note 3)
Output Voltage at Pin13 at Nominal Contrast/Saturation and
No Luminance Signal to (R–Y) (Peak–to–Peak Value)
Maximum Peak–White Level (Note 8)
Maximum Output Current (Pin13, Pin14, Pin15)
Output Black Level Voltage for a Brightness Control Voltage
at Pin12 of 2V
Black Level Shift with Vision Contents
Brightness Control Input Current
Variation of Black Level with Temperature
Variation of Black Level with Contrast
Note 3. Nominal contrast is specified as the maximum contrast –3dB and nominal saturation as the
maximum saturation –6dB.
Note 7. These signal amplitudes are determined by th ACC circuit of the reference part.
Note 8. If the typical voltage for this white level is exceeded, the output voltage is reduced by discharging the capacitor at Pin7 (contrast control); discharge current is 1.5mA.
Electrical Characteristics (Cont’d): (VP = V1–23 = 12V, TA = +25°C unless otherwise specified)
Parameter
Symbol
Min
Typ
Max
Unit
1.9
2.1
2.3
V
Difference in Blanking Level of the Three Channels
–
0
–
mV
Differential Drift of the Blanking Levels over a
Temperatue Range of 40°C
–
0
–
mA
Tracking of Output Black Level with Supply Voltage
–
1.1
–
62
–
–
dB
–
75
150
mV
–
50
–
Ω
–
–
–3
dB
RGB Matrix and Amplifiers (Cont’d)
Blanking Level at the RGB Outputs
Signal–to–Noise Ratio of Output Signals (Note 5)
S/N
Residual 7.1MHz Signal and Higher Harmonics at the RGB Outputs
(Peak–to–Peak Value)
Output Impedance of RGB Outputs
|Z13, 14, 15–23|
Frequency Response of Total Luminance and RGB Amplifier Circuits
for f = 0 to 5MHz
Sandcastle Input (PIn8)
Level at which the RGB Blanking is Activated
V8–23
1.0
1.5
2.0
V
Level at which Burst Gate and Clamping Pulse are Separated
V8–23
6.5
7.0
7.5
V
Delay Bteween Black Level Clamping and Burst Gate Pulse
td
–
0.4
–
µs
Input Current at V8–23 = 0 to 1V
–I8
–
–
1
mA
Input Current at V8–23 = 1V to 8.5V
I8
–
20
–
µA
Input Current at V8–23 = 8.5V to 12V
I8
–
–
2
mA
Note 5. The signal–to–noise ratio is defined as peak–to–peak signal with respect to RMS noise.
Functional Description:
Luminance Amplifier
The luminance amplifier is voltage driven and requires an input signal of 450mV peak–to–peak (positive video). The luminance delay line must be connected between the IF amplifier and the decoder.
The input signal must be AC coupled to the input Pin9.
The black level at the output of the preamplifier is clamped to a fixed DC level by the black level clamping circuit. The high input impedance of the luminance amplifier minimizes disturbance of the input
signal black level by the source impedance (delay line matching resistors).
During clamping the low input impedance reduces noise and residual signals. After clamping the signal is fed to a peaking stage. The overshoot is defined by the capacitor connected to Pin10 and the
peaking is adjusted by the control voltage at Pin11.
The peaking stage is followed by a contrast control stage. The contrast control voltage range (Pin7)
is nominally –17 to +3dB.
Chrominance Amplifier
The chrominance amplifier has an asymmetrical input. The input signal must be AC coupled (Pin3)
and have a minimum amplitude of 55mV peak–to–peak. The gain control stage has a control range
in excess of 30dB, the maximum input signal should not exceed 1.1V peak–to–peak, otherwise clipping of the input signal will occur. From the gain control stage the chrominance signal is fed to the
saturation and contrast control stages. Chrominance and luminance control stages are directly
coupled to obtain good tracking. Saturation is linearly controlled via Pin6. The control voltage range
is 2V to 4V, the input impedance is high and the saturation control range is in excess of 50dB. The
burst signal is not affected by saturation control. The output signal at Pin24 is AC coupled to the demodulators via Pin17.
Functional Description (Cont’d):
Oscillator and ACC Detector
The 7.16MHZ reference oscillator operates at twice the subcarrier frequency. The reference signals
for the (R–Y) and (B–Y) demodulators, the burst phase detector, and ACC detector are obtained via
the divide–by–2 circuit, which provides a 90° phase shift. The oscillator is controlled by the burst
phase detector, which is gated with the narrow part of the sandcastle pulse (Pin8). As the burst phase
detector has an asymmetrical output the oscillator can be adjusted by changing the voltage of the output (Pin21) via a high–ohmic resistor. The capacitor in series with the oscillator crystal must then have
a fixed value. When Pin6 (saturation control) is connected to the positive supply line the burst signal
is suppressed and the color killer is overruled. This position can therefore be used for adjustment of
the oscillator. The adjustment is visible on the screen.
The hue control is obtained by changing the phase of the input signal of the burst phase detector with
respect to the chrominance signal applied to the demodulators. This phase shift is obtained by generating a 90° shift sine–wave via a Miller integrator (biased via Pin19) which is mixed with the original
burst signal. A control circuit is required in the 90° phase shift circuit to make the chrominance voltage
independent of the hue setting. This control circuit is decoupled by a capacitor connected to Pin5.
As the shifted burst signal is synchronously demodulated in a separate ACC detector to generate the
ACC voltage, it is not affected by the hue control. The output pulses of this detector are peak detected
(Pin4) to control the gain of the chrominance amplifier, thus preventing blooming–up of the color during weak signal reception. This ensures reliable operation of the color killer. During color killing the
color channel is blocked by switching–off saturation control and the demodulators.
Demodulators
The (R–Y) and (B–Y) demodulators are driven by the chrominance signal (Pin24) and the reference
signals from the 7.16MHZ divider circuit. The phase angle between the two reference carriers is 115°.
This is achieved by the (R–Y) demodulator receiving an additional phase shift by mixing the two signals from the divider circuit. The phase shift of 115° can be varied between 90° and 140° by changing
the bias voltage at Pin18. The demodulator output signals are fed to R and B matrix circuits and to
the (G–Y) matrix to provide the (G–Y) signal which is applied to the G matrix. The demodulator circuits
are killed and blanked by bypassing the input signals.
RGB Matrix and Amplifiers
The three matrix and amplifier circuits are identical and only one circuit will be described. The luminance and the color difference signals are added in the matrix circuit to obtain the color signal. Output
signals are 5V (p–p) (black–white) for the following nominal input signals and control settings.
D Luminance 450mV(p–p)
D Chrominance 550mV(p–p) (burst–to–chrominance ratio of the input 1: 2.2)
D Contrast–3dB max
D Saturation–6dB max
The maximum output voltage is approximately 7V(p–p). The black level of the blue channel is compared with a variable external reference level (Pin12), which provides the brightness control. The
brightness control range is 1V to 3.2V. The control voltage is stored in a capacitor (connected to
Pin16) and controls the black level at the output (Pin15) between 2V and 4V, via a change of the level
of the luminance signal before matrixing.
Note
Black levels of up to approximately 6V are possible, but amplitude of the output signal is reduced to
3V(p–p).
If the output signal surpasses the level of 9V the peak–white limiter circuit becomes active and reduces the output signal via the contrast control.
Functional Description (Cont’d):
Blanking of RGB Signals
The RGB signals can be blanked via the sandcastle input (Pin8). A slicing level of 1.5V is used for
this blanking function, so that the wide part of the sandcastle pulse is separated from the remainder
of the pulse. During blanking a level of +2V is available at the output.
Pin Connection Diagram
24 Chroma Output
VCC 1
ACC Detector 2
23 GND
22 OSC
Chroma Input 3
Peak Detector 4
21 OSC Adjust
20 Hue Control
Decoup Cap 5
19 Hue Control
Signal
18 Reference
Phase Adjust
17 Chroma Demod
Input
16 Black Level Clamp
Output
15 Blue Output
14 Green Output
Saturation Control 6
Contrast Control 7
Sandcastle Pulse 8
Luminance Input 9
Peaking Cap 10
Peaking Control 11
Brightness Control 12
13 Red Output
24
13
1
12
1.300 (33.02)
Max
.520
(13.2)
.225
(5.73)
Max
.100 (2.54)
1.100 (27.94)
.126
(3.22)
Min
.600
(15.24)