Anachip AP1184S725 4a ultra low dropout positive adjustable or fixed-mode regulator Datasheet

AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Feature
„ General Description
0.7V maximum dropout voltage at 4A load current
Built-in Thermal shutdown
• Output current limiting
• Adjustable or fixed output voltage
1.5V, 1.8V, 2.5V, 3.3V, 5.0V
• Fast transient response
• Good noise rejection
• Packages: SOP-7L, TO220-5L and TO263-5L
AP1184 is a 4A regulator with extremely low
dropout voltage. This product is specifically
designed to provide well regulated supply for
applications requiring 2.8V or lower voltages from
3.3V ATX power supplies where high efficiency of
the switch can be achieved without the cost and
complexity associated with switching regulator. One
such application is the new graphic chipsets that
requires anywhere from 2.4V to 2.7V supply.
•
•
„ Ordering Information
AP1184 X X X X
Low Dropout Regulator
Package
Vout
Lead Free
Packing
S7:SOP-7L
K5:TO263-5L
T5:TO220-5L
Blank : Adj
15 = 1.5V
18 = 1.8V
25 = 2.5V
33 = 3.3V
50 = 5.0V
Blank : Normal
L : Lead Free Package
Blank : Tube
A : Taping
„ Typical Application
3.3V
+
470uF
GND
NC
Vsense
Vout
Vctrl
Vout
2.5V/4A
5V
+
470uF
Vin
Vin
+
470uF
AP1184-2.5V
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev.1.1 Sep 7, 2004
1/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Block Diagram
Vin
Vout
Vsense
Vctrl
+
+
1.25V
-
CURRENT
LIMIT
+
+
-
THERMAL
SHUTDOWN
Adj
„ Pin Configuration
FRONT VIEW
FRONT VIEW
5
4
3
2
1
Vin
Vctrl
Vout
Adj(GND)
Vsense
Adj(GND)
1
8
Vsense
2
7
Vctrl
3
6
Vin
4
5
NC
Vin
Vctrl
Vout
Adj(GND)
Vsense
5
Vout
4
3
Vin
2
1
Tab is Vout
Tab is Vout
( AP1184S7 )
(AP1184K5)
(AP1184T5)
„ Pin Descriptions
Pin Numbers with standard type are for TO220-5L, TO263-5L packages, and those with boldface type are for SOP-7L
Name
Adj
(GND)
I/O
Vsense
I
Vin
I
Vctrl
I
NC
Vout
O
Description
A resistor divider from this pin to the Vout pin and ground sets the output voltage.
(GND only for fixed mode)
This pin is the positive side of the reference that allows remote load sensing to
achieve excellent load regulation. A minimum of 10uF capacitor must be connected
from this pin to ground to insure stability.
The input of the regulator. Typically a large storage capacitor is connected from this
pin to ground to insure that the input voltage does not sag below the minimum
dropout voltage during the load transient response. This pin must always be higher
than Vout in order for the device to regulate.
This pin is the supply pin for the internal control circuit as well as the base drive for
the pass transistor. This pin must always by higher than the Vout pin in order the
device to regulate. A minimum of 100uF capacitor must be connected from this pin to
ground to insure stability.
No connection
The output of the regulator. A minimum of 100uF capacitor must be connected from
this pin to ground to insure stability.
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
2/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Absolute Maximum Ratings
Symbol
Parameter
Rating
Unit
VIN
Input Voltage
16
V
Vctrl
Control Input voltage
18
V
PD
Power dissipation
TST
Storage temperature Range
TOP
Internally limited
Operation Junction Temperature Range
-65 to +150
o
C
0 to +150
o
C
„ Electrical Characteristics
o
o
Unless otherwise specified, these specifications apply over, Cin=1uF, Cout=10uF, and Tj=0 to 150 C. Typical value refer to Tj=25 C.
Vout=Vsense.
Sym.
Parameter
VREF Reference Voltage
Line Regulation
Vout
Output Voltage
Load
Regulation
Dropout Voltage
(Vctrl –Vout)
Dropout Voltage
(Vin -Vout)
Current Limit
Minimum Load
Current
Test Condition
o
Io=10mA, Tj=25 C, (Vin-Vout)=0.7V,
AP1184-Adj
Vctrl=VIN+1V
o
IO=10mA, VOUT+0.7V<VIN<12V, TJ =25 C
AP1184-XXX
Vctrl=VIN+1V
IOUT = 10mA, TJ = 25oC, 2.2V≦VIN≦12V
AP1184-1.5
Vctrl=VIN+1V
IOUT = 10mA, TJ = 25oC, 2.5V≦VIN≦12V
AP1184-1.8
Vctrl=VIN+1V
o
IOUT = 10mA, TJ = 25 C, 3.2V≦VIN≦12V
AP1184-2.5
Vctrl=VIN+1V
IOUT = 10mA, TJ = 25oC, 4.0V≦VIN≦12V
AP1184-3.3
Vctrl=VIN+1V
o
IOUT = 10mA, TJ = 25 C, 5.7V≦VIN≦12V
AP1184-5.0
Vctrl=VIN+1V
0mA<Io<4A, TJ =25oC
AP1184-Adj
(VIN- VOUT)=2V ,Vctrl =VIN + 1V
o
VIN=3V, 0mA<Io<4A, TJ =25 C
AP1184-1.5
Vctrl=4V
o
VIN=3.3V, 0mA<Io<4A, TJ =25 C
AP1184-1.8
Vctrl=4.3V
o
VIN=4V, 0mA<Io<4A, TJ =25 C
AP1184-2.5
Vctrl=5V
VIN = 5V, 0mA<Io<4A, TJ=25oC
AP1184-3.3
Vctrl=6V
VIN = 8V, 0mA<Io<4A, TJ=25oC
AP1184-5.0
Vctrl=9V
Vadj=0V for all conditions below.
Vin=2.05V, Io=1.5A
Vin=2.05V, Io=3A
Vin=2.05V, Io=4A
Vadj=0V for all conditions below.
Vctrl =2.75V, Io=1.5A
Vctrl =2.75V, Io=3A
Vctrl =2.75V, Io=4A
Vctrl =2.75V, Vin=2.05V,∆Vo=100mV, Vadj=0V
Vctrl =5V, Vin=3.3V, Vadj=0V
Min. Typ.
Max. Unit
1.225 1.250
1.275
V
0.2
%
1.470 1.500
1.530
V
1.764 1.800
1.836
V
2.450 2.500
2.550
V
3.235 3.300
3.365
V
4.900 5.000
5.100
V
1
%
12
15
mV
15
18
mV
20
25
mV
26
33
mV
40
50
mV
1.10
1.15
1.18
1.25
0.26
0.50
0.70
0.38
0.60
0.85
4.2
V
A
5
Anachip Corp.
www.anachip.com.tw
V
10
mA
Rev.1.1 Sep 7, 2004
3/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Electrical Characteristics(Continued)
o
o
Unless otherwise specified, these specifications apply over, Cin=1uF, Cout=10uF, and Tj=0 to 150 C. Typical value refer to Tj=25 C.
Vout=Vsense.
Sym.
Iadj
θ JC
Parameter
Test Condition
Thermal Regulation 30mS Pulse
Vctrl =5V, Vin=5V, Io=4A, Vadj=0V, Tj=25, Vripple=1Vpp at
Ripple Rejection
120Hz
Vadj=0V for all conditions below.
V =2.75V, Vin=2.05V, Io=1.5A
Control Pin Current ctrl
Vctrl =2.75V, Vin=2.05V, Io=3A
Vctrl=2.75V, Vin=2.05V, Io=4A
Adjust Pin Current Vctrl=2.75V, Vin=2.05,Vadj=0
TO-263: Control Circuitry/Power Transistor
Thermal Resistance
TO-220: Control Circuitry/Power Transistor
Junction-to-Case
SOP-7: Control Circuitry/Power Transistor
Min. Typ.
0.01
60
Max. Unit
0.02
%/W
70
6
30
33
50
3.5
2.5
20
dB
25
60
70
150
mA
µA
C/W
O
C/W
O
C/W
O
NOTE:
AP1184-ADJ incorporates an internal thermal shutdown that protects the device when the junction temperature exceeds the allowable
maximum junction temperature.
Package
TO263/TO220
SOP7
Max Pd.
2.4W~4.4W
1W~2W
Remarks
With heat sink or amount of copper board needed.
With heat sink or amount of copper board needed.
„ Functional Descriptions
current from zero to several amps in tens of
nanoseconds at the processor pins, which
translates to an approximately 300 to 500ns of
current step at the regulator. In addition, the output
voltage tolerances are also extremely tight and they
include the transient response as part of the
specification.
The AP1184 is specifically designed to meet the
fast current transient needs as well as providing an
accurate initial voltage, reducing the overall system
cost with the need for fewer number of output
capacitors. Another feature of the device is its true
remote sensing capability that allows accurate
voltage setting at the load rather than at the device.
Introduction
The AP1184 regulator is 5 terminal device designed
specifically to provide extremely low dropout
voltages comparable to the PNP type without the
disadvantage of the extra power dissipation due to
the base current associated with PNP regulators.
This is done by bringing out the control pin of the
regulator that provides the base current to the
power NPN and connecting it to a voltage that is
greater than the voltage present at the Vin pin. This
flexibility makes the AP1184 ideal for applications
where dual inputs are available such as a computer
motherboard with an ATX style power supply that
provides 5V and 3.3V to the board. One such
application is the new graphic chip sets that require
anywhere from 2.4V to 2.7V supply. The AP1184
can easily be programmed with the addition of two
external resistors to any voltages within the range
of 1.25V to 15.5V. Another major requirement of
these graphic chips is the need to switch the load
Output Voltage Setting
The AP1184-ADJ can be programmed to any
voltages in the range of 1.25V to 15.5V with the
addition of R1 and R2 external resistors according
to the following formula:
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
4/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Functional Descriptions(Continued)
Vout = Vref (1+R2/R1) + Iadj * R2 where : Vref = 1.25V & Iadj=50uA Typically
Vin
Vout
AP1184-ADJ
Vctrl
Vsense
Vref
Adj
Iadj=50uA
The AP1184-ADJ keeps a constant 1.25V between
the Vsense pin and the Adj pin. By placing a
resistor R1 across these two pins and connecting
the Vsense ans Vout pin together, a constant
current flows through R1, adding to the Iadj current
and into the R2 resistor producing a voltage equal
to the (1.25/R1)*R2 + Iadj*R2. This voltage is then
added to the 1.25V to set the output voltage. This is
summarized in the above equation. Since the
minimum load current requirement of the
AP1184-ADJ is 10mA, R1 is typically selected to be
a 121 Ω resistor so that it automatically satisfies
this condition. Notice that since the Iadj is typically
in the range of 50uA it only adds a small error to the
Vin
R1+
R2+
output voltage and should be considered when very
precise output voltage setting is required.
Load Regulation
Since the AP1184 has separate pins for the output
(Vout) and the sense (Vsense), it is ideal for
providing true remote sensing of the output voltage
at the load. This means that the voltage drops due
to parasitic resistance such as PCB traces between
the regulator and the load are compensated for
using remote sensing. Figure following shows a
typical application of the AP1184-ADJ with remote
sensing.
Vin
Vout
AP1184-ADJ
Vsense
Vctrl
Vctrl
Adj
R1
RL
R2
100uF to 1000uF. Fortunately as the capacitance
increases, the ESR decreases resulting in a fixed
RC time constant. The AP1184-XXX takes
advantage of the phenomena in making the overall
regulator loop stable. For most applications a
minimum of 100uF aluminum electrolytic capacitor
insures both stability and good transient response.
Stability
The AP1184-XXX requires the use of an output
capacitor as part of the frequency compensation in
order to make the regulator stable. Typical designs
for the microprocessor applications use standard
electrolytic capacitors with typical ESR in the range
of 50 to 100m Ω and an output capacitance of
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
5/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Functional Descriptions(Continued)
Thermal Design
The AP1184-XXX incorporates an internal thermal
shutdown that protects the device when the junction
temperature exceeds the allowable maximum
junction temperature. Although this device can
operate with junction temperatures in the range of
150oC, it is recommended that the selected heat
sink be chosen such that during maximum
continuous load operation, the junction temperature
is kept below this number. The example below
shows the steps in selecting the proper surface
mount package.
Package
SOP7
TO263
Copper Area
1.0” X 1.0”
Pad Size-1.4”X1.4”
Assuming, the following conditions:
Vout=2.5V
Vin=3.3V
Vctrl=5V
Iout=2A DC Avg.
Calculate the maximum power dissipation using
the following equation:
Pd=Iout*(Vin-Vout)+(Iout/60)*(Vctrl-Vout)
Pd=2*(3.3-2.5)+(2/60)*(5-2.5)=1.68W
Using table below select the proper package
and the amount of copper board needed.
o
Max Pd (Ta=25oC)
1.7W
2.4W-4.4W
θJA ( C/W)
65
25-45
Max Pd (Ta=45oC)
1.4W
2.0W-3.6W
o
Note: Above table is based on the maximum junction temperature of 135 C.
As shown in the above table, any of the two packages will do the job. For low cost applications the SOP7 package is
recommended.
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
6/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Performance Characteristic
800
750
700
1200
Vpower = 2.05 V
Vpower Dropout Voltage (mV)
Vcontrol Dropout Voltage (mV)
1100
1000
Tj = 20 oC
900
Tj = 120 oC
800
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Vcontrol = 2.75 V
650
600
550
500
Tj = 120 oC
450
400
350
300
Tj = 20 oC
250
200
150
100
50
0
Output Current (A)
0.5
0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Output Current (A)
Vcontrol Dropout Voltage vs Output Current
Vpower Dropout Voltage vs Output Current
1. 253
0. 15
0. 14
1. 252
0. 12
1. 251
Load Regulation (%)
Reference Voltage (V)
0. 10
1. 250
1. 249
1. 248
1. 247
0
Tj = 120 oC
0. 08
0. 06
0. 04
Tj = 20 oC
0. 02
20
40
60
80
Junction Temperature ( oC)
100
0
120
Reference Voltage vs Junction Temperature
0
0.5
1.0 1.5 2.0 2.5
Output Current (A)
3.0
3.5
4.0
Load Regulation vs Output Current
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
7/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Performance Characteristic (continued )
VCONTROL = 5.0V
VPOWER = 3.3V
VOUT = 2.5V
CCONTRROL=10uF
CPOWER = 100uF
CADJ = 0.1uF
COUT = 470uF
ILOAD
10mA to 4A
Transient Response
„ Marking Information
XX:
Blank=adj,15= 1.5V,
18= 1.8V, 25=2.5V
33= 3.3V, 50= 5.0V
( Top View)
Logo
Part Number
1184-XX
YY WW X X
Blank: normal
L: Lead Free Package
~
X : Internal code ( Optional)
WW : Nth week : 01~52
YY : Year : "01"=2001
"02"=2002
( SOP-7L / TO220-5L / TO263-5L )
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Sep 7, 2004
8/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
„ Package Outline
(1). Package Type: TO220-5L
E
A
F
L
D
H1
Q
ΦP
b
e
C
J1
e1
Symbol
A
b
C
D
E
e
e1
F
H1
J1
L
Øp
Q
Dimensions In Millimeters
Min.
Nom.
Max.
4.07
4.45
4.82
0.76
0.89
1.02
0.36
0.50
0.64
14.22
14.86
15.50
9.78
10.16
10.54
1.57
1.71
1.85
6.68
6.81
6.93
1.14
1.27
1.40
5.46
6.16
6.86
2.29
2.74
3.18
13.21
13.97
14.73
3.68
3.81
3.94
2.54
2.73
2.92
Anachip Corp.
www.anachip.com.tw
Dimensions In Inches
Min.
Nom.
Max.
0.160
0.175
0.190
0.030
0.035
0.040
0.014
0.020
0.025
0.560
0.585
0.610
0.385
0.400
0.415
0.062
0.067
0.073
0.263
0.268
0.273
0.045
0.050
0.055
0.215
0.243
0.270
0.090
0.108
0.125
0.520
0.550
0.580
0.145
0.150
0.155
0.100
0.107
0.115
Rev.1.1 Sep 7, 2004
9/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
(2). Package Type: TO263-5L
E
2.5
L
D
15.7
9.1
L2
10.9
1.0
1.7
C2
A
Land Pattern Recommendation (Unit: mm)
B
C
e
L1
Symbol
A
B
C
C2
D
E
e
L
L1
L2
Dimensions In Millimeters
Min.
Nom.
Max.
4.07
4.46
4.85
0.66
0.84
1.02
0.36
0.50
0.64
1.14
1.27
1.40
8.65
9.15
9.65
9.78
10.16
10.54
1.57
1.71
1.85
14.61
15.24
15.88
2.29
2.54
2.79
2.92
Anachip Corp.
www.anachip.com.tw
Dimensions In Inches
Min.
Nom.
Max.
0.160
0.176
0.191
0.026
0.033
0.040
0.014
0.020
0.025
0.045
0.050
0.055
0.341
0.360
0.380
0.385
0.400
0.415
0.062
0.068
0.073
0.575
0.600
0.625
0.090
0.100
0.110
0.115
Rev.1.1 Sep 7, 2004
10/11
AP1184
4A Ultra Low Dropout Positive Adjustable or Fixed-mode Regulator
(3). Package Type: SOP-7L
C2
C3
B1 B2
A
E
C1
C
e
D
β
F
Symbol
A
B1
B2
C
C1
C2
C3
D
E
e
F
β
Dimensions In Millimeters
Min.
5.79
3.83
3.78
4.80
1.57
0.32
1.17
0.19
0.48
1.35
Nom.
5.99
3.91
3.86
4.87
1.67
0.4
1.27
0.22
1.04REF
0.68
1.45
7o
Dimensions In Inches
Max.
6.19
3.99
3.94
4.94
1.77
0.48
1.37
0.25
Min.
0.228
0.151
0.149
0.189
0.062
0.013
0.046
0.007
0.88
1.55
0.019
0.053
Anachip Corp.
www.anachip.com.tw
Nom.
0.236
0.154
0.152
0.192
0.066
0.016
0.050
0.009
0.041REF
0.027
0.057
7o
Max.
0.244
0.157
0.155
0.194
0.070
0.019
0.054
0.010
0.035
0.061
Rev.1.1 Sep 7, 2004
11/11
Similar pages