POWER LDO06C Series 30 Watts Data Sheet Total Power: Input Voltage: # of Outputs: 30 Watts 3 - 13.8 Vdc Single SPECIAL FEATURES 6 A output current rating Input voltage range: 3 - 13.8 Vdc Adjustable output voltage: 0.59 - 5.1 V Optional factory setting with power good Electrical Specifications Excellent transient response Input Power enable Input voltage range Minimum airflow Input current Minimum load Remote OFF 50 mA 5 mA Termination voltage capability Input current (max.) See Note 3 6 A @ lo max. RoHS compliant Start-up time Power up Remote ON/OFF 3 ms 2 ms SAFETY Output UL, cUL 60950-1 Output voltage See Note 5 0.59 - 5.1 V TÜV Product Service (EN60950) Output setpoint accuracy 0.1% trim resistors ±1.0% CE Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% Small package 3 - 13.8 Vdc Min./max. load 0 A/6 A Overshoot At turn-on 0.5% max. Undershoot At turn-off 100 mV max. Ripple and noise 5 Hz to 20 MHz See Note 1 20 mV Vin = 5 V, Vout = 2.5 V Transient response See Note 1, 2 130 mV max. deviation 15 μs recovery to within regulation band Efficiency (high input) Vin = 5 V, Vo = 2.5 V, lo = 6 A 92% Switching frequency Fixed 760 kHz General Material flammability UL94V-0 Weight 1.899 g (0.067 oz.) MTBF 12 V @ 40 °C, 100% load Bellcore 332 8,222,210 hours Coplanarity Surface mount models 150 μm LDO06C Series Data Sheet Environmental Specifications Thermal performance Operating ambient temperature -40 °C to +85 °C See Note 5 Non-operating ambient temperature -40 °C to +125 °C Protection Short-circuit Hiccup, non-latching Overvoltage protection Hiccup, non-latching Recommended System Capacitance Input See Note 6 0 μF Output See Note 7 0 μF Ordering Information Model Number (3,5) Regulation Output Power (Max.) Input Voltage Output Voltage Output Current (Min.) Output Current (Max.) Efficiency (Typical) Line Load LDO06C-005W05-VJ 30 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 6A 92% ±0.2% ±0.5% LDO06C-005W05-HJ 30 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 6A 92% ±0.2% ±0.5% LDO06C-005W05-SJ 30 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 6A 92% ±0.2% ±0.5% Part Number System with Options Product Family LDO Product Family LDO = LDO Series Rated Output Current 06 Rated Output Current 06 = 6 Amp Performance Input Voltage Number of Pins Type of Output C 00 5W Performance C = Cost Optimized Input Voltage 00 = 3 - 13.8 V Type of Output 5 W = 5 Pins and Wide Output Output Voltage Mounting Option 05 Output Voltage 05 = 0.59 - 5.1 V Custom Option V X Mounting Option V = Vertical H = Horizontal S = Horizontal SMT VS = Vertical SMT Custom Option Output Voltage Adjustment of the LDO06C Series Notes: The ultra-wide output voltage trim range offers major advantages to users who select the LDO06C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59 - 5.1 Vdc. When the LDO06C converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. 3. External input fusing is recommended. RoHS Compliance J RoHS Compliance J = Pb free (RoHS 6/6 compliant) 1. Measured as per recommended system capacitance. See Technical Reference Note. 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo to full lo and full lo to 0.50. 4. Additional part numbers may be available with different output voltages. 5. Airflow dependent, 100 LFM minimum required. 6. No capacitors needed for ripple current stability. 7. No capacitors needed for stability. 8. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded Technologies representative or use the on-line model number search tool at http://www.Artesyn.com/power to find a suitable alternative. LDO06C Series Data Sheet Mechanical Drawings Vertical Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 0.371 (9.42) 0.062 (1.547) 0.410 (10.41) 0.055 (1.40) 0.650 (16.51) PIN 5 PIN 1 0.16 ±0.010 (4 ±0.25) 0.050 (1.27) TYP 0.071 (1.80) 0.025 (0.64) ±.001 SQ PINS TYP 4X 0.067 (1.70) Horizontal Mount 0.062 (1.57) REF 0.443 (11.25) 0.025 (0.64) ±.001 SQ PINS TYP 6 0.410 (10.41) 0.650 (16.51) 0.580 (14.73) 0.120 (3.05) TYP 0.125 (3.18) TYP 0.035 (0.89) PIN 1 PIN5 0.000 (0) 0.050 (1.27) 0.071 (1.80) 0.138 (3.51) 0.205 (5.21) 0.272 (6.91) 0.339 (8.61) 0.055 (1.40) REF LDO06C Series Data Sheet Mechanical Drawings Mating Connectors Surface Mount 0.441 (11.20) 0.062 (1.57) REF PIN 7 0.410 (10.41) 0.650 (16.51) PIN 6 LDO06C005W05- 0.580 (14.73) 0.040 (1.02) REF PIN 5 PIN 1 0.055 (1.40) REF 0.035 (0.89) REF 0.025 (0.64) REF 0 (0.00) 0.050 (1.27) 0.071 (1.80) 0.138 (3.51) 0.205 (5.21) 0.272 (6.91) 0.339 (8.61) 0.360 (9.14) 0.125 (3.18) TYP Pin Assignments Single Output 1 2 3 4 5 6 7 Enable Vin Common/RTN Vout PG/Trim Mech Pin (Horz/SMT only) Mech Pin (Horz/SMT only WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] LDO06C DS 27Mar2015