Ordering number : ENA2118A LC898212XA CMOS LSI AF Control LSI Overview The AF control device, LC898212XA (LC898212XA-MH), provides an ideal way to implement the reduced power consumption and the improved autofocus precision and speed (reduced convergence time) required in high-pixelcount camera modules for use in smartphones. The LC898212XA integrates on a single chip an equalizer circuit employing digital calculation, and it can be combined with position sensors to build a closed-loop actuator control system. Since closed-loop control provides better ability to maintain the control object than conventional open-loop systems and is not affected by position differences, the LC898212XA is ideal for use in AF systems used in a wide variety of cameras. A closed-loop system uses position sensors for position control, and power consumption is lower than with conventional open-loop control, which uses current values for position control. In addition, a new PWM drive system employed suppresses noise that could affect image quality while achieving reduced power consumption, making this IC ideal for use in mobile devices such as smartphones. The filter coefficients of the equalizer circuit can be adjusted to any values desired by making register settings via I2C communication. This makes it possible to build a control circuit optimized to the various types of actuators and thereby achieve faster autofocus (reduced convergence time) performance. The integrated ADC provides up to 10-bit precision for highly accurate AF position control. Also integrated on-chip are a constant current supply DAC for drive and an op-amp with adjustable gain for use with the position sensors indispensable for building a closed-loop control system. * I2C Bus is a trademark of Philips Corporation. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. 91212HK/82912HKPC 20111107-S00001 No.A2118-1/5 LC898212XA Features Built-in equalizer circuit using digital operation AF control equalize circuit Any coefficient can be specified by I2C I/F I2C Interface Built-in A/D converter Maximum 10-bit Input 2 channel Built-in D/A converter 8-bit Output 2-channel (Hall offset, Constant current Bias) Built-in OP Amp 1 channel Hall Amp Built-in OSC 48MHz (Frequency adjustment function) Built-in PWM pulse generator circuit PWM circuit for AF control 1-chip motor driver Saturation drive H bridge 1 channel Package WL-CSP 12-pin Lead-free, halogen-free Supply voltage Logic unit: Internal core typ 1.2V (1.08V to 1.32V), AVDD (2.6V to 3.6V) Driver unit: VM (2.6V to 3.6V) Package Dimensions unit : mm (typ) 3440 TOP VIEW BOTTOM VIEW 0.4 0.285 SIDE VIEW 0.285 1 2 0.4 1.77 3 4 1.37 (0.43) B A 0.21 SIDE VIEW C 0.69 MAX 0.26 SANYO : WLP12(1.77x1.37) No.A2118-2/5 LC898212XA Block Diagram I2CDT I2CCK I2C I/F AVDD DA VM PGND BIASO H Bridge Driver OUT1 OUT2 OPINP Hall OPINM AD EQ PWM Modulation Output Control logic AVDD VDD OSC POR REG VDDO VSS No.A2118-3/5 LC898212XA Pin Description TYPE I INPUT P O OUTPUT B BIDIRECTION Power supply, GND NC I2C interface I2CCK I2CDT B B I2C Clock pin I2C Data pin D/A interface BIASO O D/A output (Hall bias input) Op-Amp interface OPINP OPINM I I Op-Amp input Op-Amp input Driver interface OUT1 OUT2 O O Actuator output pin Actuator output pin Power supply pin VDD VSS VDDO VM PGND P P P P P Digital power supply Digital GND LDO power supply out Motor power supply Power GND NOT CONNECT PIN TYPE “O” – Ensure that it is set to OPEN. PIN TYPE “I” – OPEN is inhibited. Ensure that it is connected to the VDD or VSS even when it is unused. (Please contact SANYO Electric Co., Ltd. for more information about selection of VDD or VSS.) PIN TYPE “B” – If you are unsure about processing method on the pin description of pin layout table, please contact us. Note that incorrect processing of unused pins may result in defects. If you have any question, please feel free to contact us. Pin Layout Circuit Name Number of Pins Circuit Name Number of Pins Analog 4 Driver 4 Logic 4 Backside pin layout diagram (Top View from the mold side) 4 VDDO VM PGND 3 AVDD I2CDT OUT1 2 OPINP I2CCK OUT2 1 VSS OPINM BIASO A B C No.A2118-4/5 LC898212XA SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of September, 2012. Specifications and information herein are subject to change without notice. PS No.A2118-5/5